Safety Before using your Foredom® power tool with any of the accessories shown in this catalog, please read all of the supplied safety instructions. They are for your protection and should always be followed to reduce the risk of personal injury or damage to the tool. Safety products, including glasses, ear plugs and respirator, are shown below. It is Extremely Important to Follow these Instructions:
Always wear proper eye and face protection. Wear safety glasses or face shields whenever you operate a Foredom or any power tool to prevent serious eye or face injuries.
•
• Always use a proper dust collection system or wear a respirator to prevent the inhalation of dust particles, polishing compounds, or other debris into the lungs.
Do not wear loose fitting clothing or jewelry. Loose clothing or jewelry can become entangled in the rotating accessory. Be sure to tie back or secure long hair.
•
Accessories in this catalog are rated for use at speeds indicated with a 1″ (25mm) overhang or less. Overhang is the distance from the front of collet or chuck jaw to the tip or point of the bur, mounted abrasive, or other rotary accessory.
•
• Never operate any accessory at speeds above its maximum rated speed. Rotary accessories last longer and provide their best performance by applying gentle but firm pressure to the work piece and letting the speed of the motor do the work. Pay close attention to the Maximum Speed listed for an accessory and never exceed this rating. Maximum Speed is the highest speed at which an accessory can safely be run. If used at higher speeds, an accessory can fly apart, bend, or self destruct, resulting in possible serious injury to the operator or a bystander. • Extra care should be used with an accessory that has a lower max speed rating than the speed of the motor. When properly used, all of Foredom's accessories can be operated at the speed ratings listed in this Catalog or on packaging. Always find out the manufacturer's speed rating before using accessories other than those from Foredom.
Part Numbers and Prices are shown in red on each page.
NEW
Safety Products
AK6100 $20.50
Made in USA.
Safety Kit Use this collection of safety products while running your Foredom or other power tool. Items come packed in plastic storage case.
A-SG3 $16.20 Safety Glasses Clear polycarbonate glasses with a contemporary style and unitary lens design. Temples are length adjustable with slotted ends. Comes with black neck cord.
A-6103-10 $5.00/10 pk 3M Soft Foam Ear Plugs
A-6106-6 $13.20/6 pk 3M Particulate Respirator
These are soft foam ear plugs with a patented articulated shape for improved fit and comfort. Made of hypo-allergenic materials, they roll down for easier insertion and fit for small ear canals.
A 3-panel respirator with low profile design that folds flat and fits a wide range of face sizes. Comfortable, lightweight and convenient. Has Cool FlowTM Exhalation Valve for working in heat and humidity.
Includes A-SG3 Safety Glasses and these 3M products: A-6106-3 Respirators (3), A-6102 Roll of Vetrap tape, and A-6103-3 Soft Foam Ear Plugs (3).
A-6102 $3.40/roll
3M Vetrap Tape
Self-adhering tape is easy to apply and requires no pins, clips or adhesive to keep secure. Tape won’t loosen over time and stays in place until removed. Doesn’t stick to hair, skin, or anything else. Use to protect fingers during close work with sharp instruments. 2″ wide x 15′ long.
We owe special thanks for the cover photos to Quality Gem, Jewelry Designs, and Wagner Dental Labs of Danbury, CT; Stelray Plastic Products of Ansonia, CT, and Chris Howard of TN.
2
V Stones
TM
Made in USA. 45,000 RPM Maximum Speed
V Stones last 4 to 8 times longer and are considered a great improvement over standard aluminum oxide and silicon carbide mounted abrasives. Made with a vitrified, self-sharpening, special aluminum oxide grain with a super hard porous bond, V Stones are the coolest running and longest lasting abrasive stones. They easily cut hard metals like titanium, chrome-cobalt, nickel-cobalt, tool steel, and stainless steel, and softer metals such as lead, pewter, brass and aluminum with minimal smearing and loading. V Stones also work on ceramic tile, porcelain, wood, acrylic, glass, and marble. They can be used to shape, texture, and provide detail to carvings. Their larger head sizes and coarser grits make them more aggressive than our CeramCut Blue Stones. They are the perfect complement to these smaller and finer grit stones, and an economical alternative to plated and sintered diamond points.
3/32″ (2.35mm) Shank $3.20 Ea.
Bud
1/8″ (3.18mm) Shank $3.20 Ea.
Part Numbers for 40/60 and 80 Grit Shapes shown in Red on Separate Lines Ball Cylinder Tapered Flat Top Tree Ball Cylinder Cylinder Wheel Taper Cup
V Stones come packed in clamshells
A-V886 and A-V887 have 1/16″ (1.6mm) arbor holes for use with mandrels A-M1, A-M6, A-M13, A-M15, A-M19. See Page 21 for specs. 30,000-40,000 RPM Max Speed.
Wheel
Unmounted Wheel
A-V326 A-V336
A-V356
N/A
N/A
A-V826
A-V836
A-V846
A-V856
A-V876
A-V886
A-V327 A-V337
A-V357
A-V367
A-V397
A-V827
A-V837
N/A
A-V857
N/A
A-V887
40/60 Grit Part Nos. 80 Grit Part Nos.
Dimensions for Both 40/60 and 80 Grit Shapes 1/4 (7)
3/8 (9.5)
1/4 (7)
1/2 (13)
1/4 (7)
3/8 (9.5)
3/8 (9.5)
3/8 (9.5)
3/8 (9.5)
1/2 (13)
7/8 (22)
Head Dia″ (mm)
3/8 (9.5)
3/8 (9.5)
1/2 (13)
3/16 (5)
1/2 (13)
3/4 (20)
3/8 (9.5)
1/2 (13)
3/8 (9.5)
1/8 (3.2)
1/8 (3.2)
Head Lgth″ (mm)
Part Numbers and Prices are shown in red on each page. Dimensions Are Nominal and Slight Variations May Exist
Diamond Hones and Dressing Stones
Made in USA.
Diamond Hones Dress or reshape mounted abrasive points by lightly touching a rotating point to the diamond surface. Also for hand smoothing and shaping glass, metal, stone, bone, and plastic, and for sharpening chisels and steel instruments. 3⁄4″ x 2″ diamond pad on 6″ plastic color coded handle.
Superfine (blue) Fine (red) Medium (purple) Coarse (black)
Grit 1200 600 400 250
Price Ea. Part No. A-10342 $8.40 A-10343 8.40 A-10344 8.40 A-10345 15.80
A-10335 $1.60 Mini Dressing Stone
A-10333 $7.40 Dressing Stone
This silicon carbide block can also be used for dressing and cleaning mounted abrasive points. The flat surfaces of this block are good for reshaping the tops of abrasive points or sides into domes or cone shapes. 13⁄4″ wide x 3/4″ deep x 3/8″ high. 30 grit.
This silicon carbide block allows you to reshape mounted abrasives back to perfect concentricity by running the point in the groove comparable in size. This cleans and exposes fresh abrasive particles. 33⁄8″ wide x 11⁄4″ deep x 1⁄2″ high. 60 grit.
Use Foredom Hones and Stones to Dress & Clean these Mounted Stones– V Stones, CeramCut Blue Stones, Aluminum Oxide and Silicon Carbide Points, CW Wheels, Rubber Bonded Wheels and Rods.
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
3
CeramCut Blue® Stones Made in USA. 45,000 RPM Maximum Speed CeramCut Blue Stones have a unique ceramic and aluminum oxide abrasive grain structure that is superior in performance and life to standard aluminum oxide or silicon carbide stones. They are widely used on hard metals, including hardened and mild steel, steel alloys, chrome cobalt, titanium, platinum, and other ferrous metals. They are also suitable for use on porcelain materials and wood. CeramCut Blue Stones maintain their shape and hold their cutting edge longer than any standard abrasive stones. They are non-impregnating and non-contaminating. They remove material faster, run cooler and last 3 to 5 times longer than standard abrasives. CeramCut Stones vs. V Stones: It’s not one or the other... these two superior products are complementary and effective when used together. CeramCut Blue Stones would follow the use of V Stones as their finer grits and smaller heads help in achieving detail and a smoother finish.
3/32″ (2.35mm) Shank Individual Mounted Stones $2.40 Each
A-CK300 Large Ball Nose 80 med 1/4 (6.4) 1/2 (13)
A-CK352 Small Cylinder 120 Fine 3/32 (2.35) 1/4 (6.4)
A-CK301 Medium Ball Nose 120 fine 3/16 (4.7) 1/2 (13)
A-CK360 Tapered Wheel 120 fine 1/2 (13) 1/8 (3.2)
A-CK302 Small Ball Nose 120 fine 1/8 (3.2) 1/2 (13)
A-CK364 Tapered Wheel 80 med 1/2 (13) 1/8 (3.2)
A-CK318 Flame 80 med 5/32 (3.9) 3/8 (9.5)
A-CK322 Inverted Cone 120 fine 1/8 (3.2) 1/8 (3.2)
A-CK362 Small Tapered Wheel 120 fine 5/16 (7.9) 1/32 (.79)
A-CK375 Inverted Cone 120 fine 1/4 (6.4) 1/4 (6.4)
A-CK332 Ball 120 fine 1/8 (3.2) 1/8 (3.2)
A-CK380
A-CK384
Wheel 120 fine 1/2 (13) 1/16 (1.6)
Wheel 80 med 1/2 (13) 1/16 (1.6)
A-CK342 Tapered Cone 120 fine 1/8 (3.2) 1/4 (6.4)
A-CK390 Large Flat Taper 120 fine 1/8 (3.2) 1/2 (13)
A-CK350 A-CK354 Large Large Cylinder Cylinder 120 fine 80 med 1/4 (6.4) 1/4 (6.4) 1/2 (13) 1/2 (13)
A-CK394 Large Flat Taper 80 med 1/8 (3.2) 1/2 (13)
A-CK392 Small Flat Taper 120 fine 3/32 (2.35) 3/16 (3.7)
A-CK356 Large Cylinder 60 coarse 1/4 (6.4) 1/2 (13)
Part No. Shape Grit Head Dia″ (mm) Head Lgth″ (mm)
Part No. Shape Grit Head Dia″ (mm) Head Lgth″ (mm)
Part Numbers and Prices are shown in red on each page. Dimensions Are Nominal and Slight Variations May Exist
3/32″ (2.35mm) Shank Kits 9-Pc. $20.50 Each Kits come packed in handy hanging storage boxes. Individual CeramCut Stones come packed in clamshells
AKHK24
AKHK29
Part No.
Shape
A-CK302 A-CK342 A-CK350 A-CK360 A-CK362 A-CK364 A-CK380 A-CK384 A-CK390
Small Ball Nose Tapered Cone Large Cylinder Tapered Wheel Sm Tap’d Wheel Tapered Wheel Wheel Wheel Large Flat Taper
Grit
F F F F F M F M F
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
4
Part No.
Shape
A-CK300 A-CK301 A-CK302 A-CK318 A-CK322 A-CK332 A-CK342 A-CK352 A-CK392
Large Ball Nose Medium Ball Nose Small Ball Nose Flame Inverted Cone Ball Tapered Cone Small Cylinder Small Flat Taper
Grit
M F F M F F F F F
CeramCut Blue® Stones Made in USA. 45,000 RPM Maximum Speed
1/8″ (3.18mm) Shank Individual Mounted Stones $2.40 Each
A-CK8300
A-CK8301
A-CK8302
A-CK8318 A-CK8342 A-CK8322
A-CK8332
A-CK897
Large Ball Nose
Medium Ball Nose
Small Ball Nose
Flame
Tapered Cone
Inverted Cone
Small Ball
Flat Taper
80 med 1/4 (6.4) 1/2 (13)
120 fine 3/16 (4.7) 1/2 (13)
120 fine 1/8 (3.2) 1/2 (13)
80 med 5/32 (3.9) 3/8 (9.5)
120 fine 1/8 (3.2) 1/4 (6.4)
120 fine 1/8 (3.2) 1/8 (3.2)
120 fine 1/8 (3.2) 1/8 (3.2)
A-CK8392 A-CK8144 A-CK8352 Part No. Small Flat Taper
Small Cylinder
120 fine 120 fine 3/32 (2.35) 3/32 (2.35) 3/8 (9.5) 3/16 (4.8)
120 fine 1/8 (3.2) 1/4 (6.4)
Small Shape Cylinder 120 fine Grit 3/32 (2.35) Head Dia″ (mm) 1/4 (6.4) Head Lgth″ (mm)
1/8″ (3.18mm) Shank Individual Mounted Stones $2.70 Each
A-CK8112
A-CK890
A-CK852
A-CK846
Pear 120 fine 3/8 (9.5) 1/2 (13)
Ball Nose 80 med 1/2 (13) 1/2 (13)
Tree 120 fine 3/8 (9.5) 3/4 (19)
Flame 120 fine 1/8 (3.2) 5/16 (8.0)
A-CK8122 Large Ball 120 fine 3/8 (9.5) 3/8 (9.5)
A-CK863
A-CK844
A-CK8200
A-CK8182
Barrel 120 fine 1/4 (6.4) 3/16 (4.8)
Taper 120 fine 7/32 (5.5) 3/8 (9.5)
Wheel 120 fine 3/4 (19) 1/8 (3.2)
Wheel 120 fine 1/2 (13) 1/8 (3.2)
Part No. Shape Grit Head Dia″ (mm) Head Lgth″ (mm)
Part Numbers and Prices are shown in red on each page. Dimensions Are Nominal and Slight Variations May Exist
Unmounted Wheel A-CK480 has a 1/16″ (1.6mm) center arbor hole for use with mandrels A-M1, A-M6, A-M13, A-M15, A-M19. See Page 21. 20,000 RPM Max Speed.
1/8″ (3.18mm) Shank Kit 8-Pc. AKHK28 $18.50 Each
1/8″ (3.18mm) Shank Individual Mounted Stones $2.70 Each
1.90 ea
A-CK480 Unmounted Wheel 120 fine 1/2 (13) 1/16 (1.6)
A-CK8154 A-CK8175 Long Medium Cylinder Cylinder 80 med 80 med 3/16 (4.7) 3/8 (9.5) 3/8 (9.5) 1/2 (13)
A-CK8132 Cylinder Cup 80 med 3/8 (9.5) 1/2 (13)
A-CK872 Tapered Wheel 120 fine 1/2 (13) 1/8 (3.2)
A-CK882
Part No.
Shape
A-CK8122 A-CK8132 A-CK8144 A-CK8182 A-CK844 A-CK852 A-CK890 A-CK897
Large Ball Cylinder Cup Small Cylinder Wheel Taper Tree Ball Nose Flat Taper
Grit
F M F F F F M F
Part No.
Shape Cup 120 fine Grit Head Dia″ (mm) 1/2 (13) 1/16 (1.6) edge Head Lgth″ (mm)
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
5
Aluminum Oxide Mounted Points 35,000 RPM Maximum Speed
Made in USA.
AK150
Red Individual Points Red Aluminum Oxide mounted points are used for fast cutting on high tensile, tough materials such as steel and malleable iron. Also used on porcelain and glass. For medium to fine finishing work. Be sure to specify “Red” Part Nos. when ordering. See next page for selection of 1/8″ shank red aluminum oxides.
24-Pc Kit Red Mounted Points 3/32″ shanks $45.00
KITS
White Individual Points White Aluminum Oxide mounted points of extremely fine grit (400) for a high finish on high tensile, tough materials including gemstone, stainless steel and glass. Extremely fine cutting. Points hold their geometry well. Be sure to specify “White” Part Nos. when ordering.
AK160 24-Pc Kit White Mounted Points 3/32″ shanks $45.00
3/32″ (2.35mm) Shank Individual Points $2.10 Each
Red Aluminum Oxide Part Nos. and Grits A-1
A-2
A-3
A-4
A-5
A-6
A-7
A-8
A-9
A-10
A-11
A-12
120
120
120
100
80
80
80
80
120
120
120
100
Red Part No. Grit
A-71
A-72
A-73
A-74
A-75
A-76
A-77
A-78
A-79
A-80
A-81
A-82
White Part No.
400
400
400
400
400
400
400
400
400
400
400
400
1/8 7/32
5/16 1/32
1/4 11/32
1/4 1/4
3/8 3/64
5/32 5/32
1/4 5/64
13/64 13/64
Head Dia″ Head Lgth″
Red Part No. Grit
White Aluminum Oxide Part Nos. and Grits
Grit
Dimensions for Red and White Points 1/4 1/2
3/16 17/32
3/8 5/64
1/2 1/16
Red Aluminum Oxide Part Nos. and Grits A-13
A-14
A-15
A-16
100
120
120
100
A-17
A-18
A-19
A-20
A-21
A-22
A-23
A-24
120
80
120
150
100
100
100
100
White Aluminum Oxide Part Nos. and Grits A-83
A-84
A-85
A-86
A-87
A-88
A-89
A-90
A-91
A-92
A-93
A-94
400
400
400
400
400
400
400
400
400
400
400
400
5/32 1/4
3/16 3/64
3/32 3/32
5/64 17/64
1/4 1/4
11/64 3/16
1/4 11/64
33/64 1/16
White Part No. Grit
Dimensions for Red and White Points 1/8 9/32
1/4 9/32
1/8 13/32
3/16 5/32
Part Numbers and Prices are shown in red on each page. Dimensions Are Nominal and Slight Variations May Exist
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
6
Head Dia″ Head Lgth″
Aluminum Oxide Mounted Points Made in USA. 35,000 RPM Maximum Speed
1/8″ (3.18mm) Shank Individual Points Red Only $2.10 Each
A-61
A-62
A-63
A-64
A-65
A-66
Red
A-68
A-69 A-120 A-124 A-125 A-126 A-128 A-132 A-133 A-146 Part No.
1/2
3/8
1/2
13/32
15/32
3/8
1/2
1/2
1/4
3/8
3/16
1/8
1/8
3/16
3/4
3/32
Head Dia″
17/32
1/2
13/32
3/4
3/4
1/2
1/2
41/64
5/8
3/8
3/16
1/8
19/64
49/64
1/8
13/32
Head Lgth″
60
60
60
60
60
60
60
60
60
60
120
120
120
60
80
80
Grit
Aluminum Oxide Grinding Stones with 1/16″ (1.6mm) Center Arbor Hole Made in USA. 21,000 RPM Maximum Speed Aluminum Oxide stones used for grinding, cleaning, and smoothing very hard materials such as steel and malleable iron. Use with 3/32″ and 1/8″ shank Screw-Type Mandrels A-M1, A-M6, A-M13, A-M15, and A-M19.
Individual Unmounted Stones $1.00 Each
A-G21
A-G22
A-G23
1/2″ 120
5/8″ 120
3/4″ 100
knife-edge
knife-edge
knife-edge
Come with 3/32″ and 1/8″ shanks for mounting stones with 1/16″ holes. A-M14 is used for wheels (below) with 1/8″ holes.
Part No. Dia. Grit Thickness
A-G33
A-G34
A-G35
A-G27
A-G28
1/2″ 80 13/64″
1/2″ 80 9/64″
1/2″ 80 5/64″
3/4″ 80 13/64″
3/4″ 80 9/64″
Part No. Dia. Grit Thickness
A-M1 3/32″
A-M6 A-M13 A-M15 A-M19 A-M14 1/8″ 3/32″ 1/8″ 1/8″ 1/8″ Shank Sizes
Part Numbers and Prices are shown in red on each page. Dimensions Are Nominal and Slight Variations May Exist
Abrasive Discs and Cut-Off Wheels Made in USA. Rubber Bonded Discs A-D1 and A-D2 are suitable for grinding, smoothing, and cleaning glass, high speed steel, and other tough materials. Discs have 1/16″ (1.6mm) arbor holes. 30,000 RPM Maximum Speed Fiberglass Reinforced Cut-Off Wheels A-D6, A-D8, and A-D9 are used to cut-off, groove, and trim metal, wood, and ceramics. A-D6 has a 1/16″ (1.6mm) arbor hole, A-D8 and A-D9 have 1/8″ (3.2mm) arbor holes (see details below). 40,000 RPM Maximum Speed–A-D6, A-D8, and A-D9 Fiberglass Cut-Off Wheels Rubber Bonded Discs
A-D2
A-D1 Part No.
A-D1-5 A-D2-5 A-D6 A-D8 A-D9
A-D6 Arbor Hole
A-D8 Price
A-D9 Recommended Mandrels*
Dia
Thick
Grit
7/8″
.023″
90
1/16″
$ 1.10/5pk
11⁄4″
.062″
90
1/16″
2.10/5pk
A-M6 and A-M15
11⁄4″
.050″
60
1/16″
1.40 Each
A-M15 and A-M19
11⁄2″
.050″
60
1/8″
1.40 Each
A-M14
2″
.050″
60
1/8″
1.50 Each
A-M14
A-M1 and A-M6
* See Mandrels above and Pages 21-23 for complete specifications
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
7
Silicon Carbide Mounted Points
Made in USA.
Green Silicon Carbide mounted points for low-tensile, brittle or “smeary” type materials such as aluminum or brass. Also for stainless steel, glass, gemstones, and other non-metals. Use for a broad range of work including grinding, deburring, smoothing, and cleaning. Also for rough finishing work.
3/32″ (2.35mm) Shank Individual Points $2.10 Each 35,000 RPM Maximum Speed
A-31
A-33
A-34
A-36
A-37
A-42
A-43
A-44
A-45
A-46
A-47
A-48
A-50
1/8 7/32 150
1/4 11/32 120
1/4 1/4 120
3/16 17/32 100
3/8 5/64 150
13/64 13/64 120
5/32 1/4 150
3/16 3/64 150
3/32 3/32 180
5/64 17/64 180
1/8 9/32 150
1/4 9/32 150
3/16 5/32 150
A-51 Part No. 1/4 Head Dia″ 1/4 Head Lgth″ 120 Grit
1/8″ (3.18mm) Shank Individual Points $2.10 Each 30,000 RPM Maximum Speed Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories A-134 17/64 21/64 100
A-135 A-136 7/16 49/64 100
1/4 5/8 120
A-137 A-138 A-139 A-140 3/4 1/16 100
1/8 13/32 120
3/8 3/8 100
3/8 3/8 100
A-141 A-142 A-143 1/4 31/64 100
1/4 5/16 120
Rubber Bonded Abrasives $6.00/10Pk
A-144 Part No.
1/8 17/64 150
1/8 3/8 100
Head Dia″ Head Lgth″ Grit
Part Numbers and Prices are shown in red on each page. Dimensions Are Nominal and Slight Variations May Exist
Made in USA. 25,000 RPM Max Speed
Rubber Bonded Abrasive (silicon carbide) unmounted wheels and rod for light deburring, cleaning, smoothing, and polishing. Ideal for hard to reach areas on ferrous and non-ferrous alloys, as well as other materials. Cushioned action performance. Color coded by grit.
$6.00 per 10 Pack A-A1-10 7/8 1/8 1/16
A-A2-10 5/8 3/32 1/16
A-A3-10 5/8 1/8 1/16
A-A6-10 1/4 7/8 3/32
Part No.*
A-M1 A-M6
A-M1 A-M6
A-M1 A-M6
A-M3 A-M9
Preferred Mandrels
CW Polishing Wheels $10.50/10Pk
Head Dia.″ Head Lgth (thick)″ Center Hole
25,000 RPM Max Speed
AK120 76-Pc Kit $39.90 72 unmounted rubber bonded abrasive wheels and cylinders. 6 each of A-A1, A-A2, A-A3, and A-A6 in three grits-coarse, medium & fine, plus 3/32″ shank mandrels A-M1and A-M3 and 1/8″ shank mandrels A-M6 and A-M9.
CW Ceramic Impregnated Polishing Wheels in 6 different grits for smoothing and polishing precious metals including platinum, gold, silver, titanium, chrome cobalt, and all hard alloys. CW non-contaminating wheels work faster and last longer than other polishers.
$10.50 per 10 Pack 7/8″ dia. x 1/8″ thick (22 x 3.2mm) CW Polishing Wheels with 1/16″ center holes.
8
Color
Grit
Part No/10 Pack
White Gray Orange Violet Green Blue Assortment Set of 10 $10.50 per set
Super fine (1500 grit) Extra fine (1000 grit) Fine (500 grit) Medium (320 grit) Med/Coarse (180 grit) Coarse (120 grit) 2 Ea. Blue, Green, Violet, Orange 1 Ea. Gray and White.
A-CW55810 A-CW55710 A-CW55610 A-CW55410 A-CW55210 A-CW55110 A-CW55010
Plated Diamond Points and Discs Made in UK. 120,000 RPM Maximum Speed Plated diamond blanks are precision turned from stainless steel to ensure proper concentricity and balance for high speed use. All corners are rounded and the plating cycle is specifically tuned for the point shape to ensure even diamond coverage and a strong bond. Features sharp, natural diamond grit that conforms to ISO specs for medium diamond grade–120-200 grit/100-60 micron. Diamond points are for use on hardened steel, glass, precious metals, ceramics, stone, and composite materials in industrial, jewelry, and laboratory applications, and on hard and soft woods for carving, fine detailing, and texturing.
2.35mm (3/32″) Shank Individual Points. Priced below. Smooth Top Smooth Top
AAPD3 PD4 1.0 1.4 .8 1.1 $6.30 6.30
APD24 1.6 1.4 6.30
AAAAAPD5 PD30 PD25 PD6 PD26 1.8 2.1 2.6 3.3 4.3 1.6 1.6 2.0 2.7 3.8 6.30 6.30 6.30 11.30 14.50
APD2 1.2 5.0 7.60
AAAAAAAPD9 PD10 PD92 PD14 PD15 PD61 PD62 2.3 4.0 7.0 1.9 2.6 3.0 4.0 7.0 8.0 14.0 7.0 7.0 10.0 10.0 6.30 8.80 17.60 6.30 6.30 7.60 8.80
AAPD1 PD11 Part No. 1.6 2.1 Head Dia mm 3.0 10.5 Head Lgth mm 6.30 11.30 Price Each
Plated Diamond Discs for Cutting and Finishing Made in Belgium. 20,000 RPM Max Speed Discs are 22mm (7/8″) in dia., with 1.6mm (1/16″) arbor holes. Recommended for use with A-M13 or A-M-19 mandrels. APD12 1.6 9.0 $6.30
AAAAAPD22 PD17 PD20 PD13 PD8
AAA- Part No. PD7 PD29 PD27 Head Dia 2.6 6.3 5.8 2.4 6.5 6.0 9.5 2.6 mm Head Lgth 8.0 8.0 2.0 10.0 2.0 4.8 6.0 2.0 mm 6.30 18.90 14.50 8.80 17.00 17.00 18.90 6.30 Price Each
Dia. mm
Total Disc Thickness
Type
Part Microns No.
Price Each
Cutting Disc (both sides plated)
22mm .45mm
NonFlex
100
A-DD1 $18.70 Each
Finishing Discs (both sides plated)
22mm .18mm
SuperFlex
50
A-DD4
23.50 Each
For smoothing, finishing, and cutting. Use top and bottom surface for smoothing and finishing, use edge for cutting.
Wet Stick A-4005 $2.60 2″ x 1/2″ x 3/4″
Finishing Discs (one side plated)
22mm .15mm
Use wet for unloading plated and sintered diamond points
SuperFlex
70
A-DD8
22.40 Each
Use for finishing only one side of a groove or other tight spot without affecting the adjoining surface.
Dumont® Sintered Diamond Points and Discs
Made in Belgium.
Sintered Diamonds last 5 to 10 times longer than plated diamonds and up to 100 times longer than various types of silicon carbide or aluminum oxide mounted abrasive points. They work with far less grinding dust and can be “re-sharpened” to expose new diamond particles as often as desired by slowly turning (@4,000 rpm/15 sec.) against a wet dressing stone (A-10333, pg. 3). Plated diamonds typically have only a single layer of diamond on a metal surface. Even new sintered points should be dressed for best results. Dumont® sintered points come in a Hard Binder of 100 Micron/120 Grit for hard precious stones and metal finishing work (especially gold) when contamination of the surface prior to application of porcelain is a potential problem.
2.35mm (3/32″) Shank Individual Points. Priced below.
25,000 RPM Max Speed
Dumont sintered diamonds have controlled man-made GE diamond crystals that are molded into a metallic binder with extreme heat and pressure in a special atmosphere. This produces a uniform matrix of more consistent diamond crystals than natural industrial diamonds embedded in a strong, durable binder. AAAAAADS712A DS753 DS756A DS758A DS742A DS746A 3.1
3.1
3.1
2.7
1.6
5.0
3.1
9.0
12.0
8.5
6.5
13.0
$30.50
36.80
36.80
30.50
30.50
44.10
A- Part No. DS22 Head Dia 22 mm Head Lgth .5 mm 47.30 Price Each
Sintered Diamond Disc A-DS22 has a solid matrix of diamonds in a binder from edge to center– the cutting edge is always exposing new diamonds. 165 micron/80 grit A-DS22 comes balanced and mounted on a 2.35mm (3/32″) shank.
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
9
3M Flexible Diamond Sanding Bands & Discs Made in USA. 3M Flexible Diamond bands and discs are made from a two-ply polyester backing film evenly coated with diamond filled nickel plated dots. Clean and unload them with the A-AC1 Abrasive Cleaner or A-HB58 Brass Brush on pgs 26 and 27. Use wet or dry.
1/4″ x 1/2″ band
1/2″ x 1″ band
1/2″ x 1/2″ band
Grind, Sand, and Smooth with Flexible Diamond Bands & Discs! glass stone • wood
carbide steel • bone
composites exotic alloys • chrome cobalt
plastic • enamels gypsum • ceramics • painted or plated surfaces
•
•
•
•
•
•
•
•
Bands in 1/4″, 3/8″, 1/2″, and 3/4″ (6, 9.5, 13 & 19mm) diameters for use with rubber drum mandrels with 3/32″ (2.35mm), 1/8″, 1/4″ and 6mm shanks. See pages 21-23 for complete mandrel listing. Discs with PSA (pressure sensitive adhesive) backs for use on disc mandrels in 3/4″ and 2″ (19 & 51mm) diameters. See pages 21-23 for complete mandrel listing.
Flexible Diamond Sanding Bands Priced Each Micron Grade
Grit
Individual Part No.
Price Each
Mandrels
Max Speed (RPM’s)
2″ disc with PSA back
discs with PSA back
Flexible Diamond PSA Sanding Discs Priced Each Micron Grade
Grit
Individual Part No.
1/4″ D x 1/2″ L (6 x 13mm)
3/4″ (19mm) PSA Discs
250 125 74 40 20 Assortment
250 125 74 40 20 Assortment
60 A-4812 $8.60 120 A-4813 5.40 220 A-4814 5.40 400 A-4817 5.40 800 A-4818 5.40 AK4810 $26.50 (1 each of five grits)
A-SD324 A-SD184
40,000
60 120 220 400 800 AK5740
A-5742 $1.90 A-5743 1.60 A-5744 1.30 A-5746 1.10 A-5748 1.10 $6.10 (1 each of five grits)
3/8″ D x 1/2″ L (9.5 x 13mm)
2″ (51mm) PSA Discs
125 120 A-4853 $5.90 74 220 A-4854 5.90 40 400 A-4857 5.90 20 800 A-4858 5.90 Assortment AK4850 $21.00 (1 each of four grits)
250 125 20
A-SD326 A-SD186
40,000
60 120 800
Price Each
A-5752 A-5753 A-5758
$21.00 17.90 15.20
Mandrels
Max Speed (RPM’s)
A-M4
15,000
A-M33 A-M338
10,000
Packaging 1/2″ D x 1/2″ L (13 x 13mm) 250 125 74 40 20 Assortment
60 A-4822 $8.10 120 A-4823 7.00 220 A-4824 6.50 400 A-4827 6.50 800 A-4828 6.50 AK4820 $29.40 (1 each of five grits)
A-SD328 A-SD188
Flex Diamond, Ceramic Purple and Aluminum Oxide, come packed in clear plastic bags with header cards. 40,000
Cerium Oxide Sanding Bands and PSA Disc Priced Each
1/2″ D x 1″ L (13 x 25mm) 250 125 74 40 20
60 120 220 400 800
A-4832 A-4833 A-4834 A-4837 A-4838
$9.70 8.60 7.50 7.50 7.50
A-SD141 A-SD661
20,000
60 120 800
A-4872 A-4873 A-4878
$11.80 11.30 8.10
60 120 800
A-4862 A-4863 A-4868
50,000
15,000
10
A-4842 A-4843
A-4402
50,000
$12.90 12.40 9.70
A-SD144 A-SD662
$14.50 12.90
A-SD145 A-SD345
Mandrels
Max Speed (RPM’s)
A-SD324 A-SD184
40,000
$2.20
A-SD328 A-SD188
40,000
$1.00
A-M4
15,000
$1.70
A-4404
3/4″ (19mm) PSA Disc A-4406
10,000
Part Numbers and Prices are shown in red on each page. Dimensions are nominal and measured in inches. Slight variations may exist.
3/4″ D x 1 ⁄ ″ L (19 x 38mm) 60 120
Price Each
1/2″ D x 1/2″ L (13 x 13mm) Band 50,000
12
250 125
Individual Part No.
1/4″ D x 1/2″ L (6 x 13mm) Band A-SD143 A-SD189
3/4″ D x 1″ L (19 x 25mm) 250 125 20
Use 3M’s Cerium Oxide Abrasives for achieving a final, high shine polish on gemstone, rock and glass. Bands and discs last longer when used wet. Results are also best when used following a 1,200 to 3,000 grit abrasive. Micron Grade
3/4″ D x 1/2″ L (19 x 13mm) 250 125 20
NEW
10,000
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
3M Film Bands & Discs
Made in USA.
2″ ImperialTM Microfinishing Film Discs Imperial Microfinishing film psa discs from 3M can be used wet or dry on metal or stone. High strength polyester film backing is coated with premium, micron graded aluminum oxide particles for greater cutting efficiency and resin bonded for increased durability. This fast-cutting abrasive provides gentle, contoured polishing. Part No.
Micron Grade Grit
2″ (51mm) PSA Discs 9 15 30 40 60 80
Part No.
$2.70/10-Pack
1200 600 400 320 220 180
$11.80/50-Pack
5
A-4591-10 A-4592-10 A-4593-10 A-4594-10 $2.70 A-4596-10 A-4598-10
6
5
A-4591-50 A-4592-50 A-4593-50 A-4594-50 $11.80 A-4596-50 A-4598-50
6
Mandrels
Max (RPM’s)
A-M33 10,000 A-M338
2″ ImperialTM Diamond Lapping Film Discs Micron Grade
Individual Part No.
Grit
Price Each
Max (RPM’s)
Mandrels
2″ (51mm) PSA Discs 3
A-4583
4000
$5.80 Ea.
A-M33, A-M338
10,000
Use Imperial Diamond Lapping Film Discs (Pink A-4583) wet to reduce heat buildup and loading. The strong, flexible 3-mil backing adheres to a flat surface such as a 2″ disc mandrel. For lapidary and metalworking.
NEW Diamond Micro Finishing Film Sanding Bands and PSA Discs Priced Each Micron Grade
Individual Part No.
Grit
Price Each
Max (RPM’s)
Mandrels
1/4″ D x 1/2″ L (6 x 13mm) Bands 125 74 45 30 20 9
120 220 320 400 600 1200
A-4412 A-4413 A-4414 A-4415 A-4416 A-4417
$3.90 3.20 3.00 2.50 2.30 2.30
A-SD324 A-SD184
40,000
A-SD328 A-SD188
40,000
A-M4
15,000
3M’s Diamond Micro Finishing abrasives have flexible film backing suitable for metal working and lapidary applications. They work great on all materials including stone, glass and hard to work on stainless steel and titanium. When working with gemstone, rock and glass they should be used wet.
1/2″ D x 1/2″ L (13 x 13mm) Bands 125 74 45 30 20 9
120 220 320 400 600 1200
A-4422 A-4423 A-4424 A-4425 A-4426 A-4427
$5.20 4.40 3.90 3.20 2.90 2.90
3/4″ (19mm) PSA Discs 125 74 45 30 20 9
120 220 320 400 600 1200
A-4432 A-4433 A-4434 A-4435 A-4436 A-4437
$4.70 3.70 3.50 2.70 1.60 1.60
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
3M Wet/Dry Micron Graded Polishing Papers $17.20 per 10-Pack of 81⁄2″ x 11″ Sheets Part No.
Price
Grade
A-5968-10 A-5967-10 A-5966-10 A-5964-10 A-5963-10 A-5962-10 AK5960
$17.20 17.20 17.20 17.20 17.20 17.20 $10.20
1 micron 10,000 white 2 micron 6,000 aqua 3 micron 4,000 pink 9 micron 1,200 lt. blue 15 micron 800 gray green 400 30 micron 6-pc Assortment Pack of 81⁄2″ x 11″ sheets–1 of each grade 6-pc Assortment Pack of 41⁄4″ x 11″ sheets–1 of each grade Super Bond Film Tape 1″ x 36 yards use for making belts for hand sanders.
AK5961
$5.20
Z-37-959
$10.00
Grit
Color
3M’s polishing paper is a soft cloth-like material for use on any contoured surface with or without water. Working in sequence from the most coarse to the finest sheet brings the best results. 81⁄2″ x 11″ sheets come in six micron grades in packs of 10 per grit. Papers can be cut lengthwise into 11⁄2″, 1″, 3/4″ or 1/2″ wide strips, taped, and made into rolls for use on Finger Sanders and Sanding Sticks. Papers can also be cut into much smaller pieces, wrapped and glued for use on split mandrels, see page 21.
11
3M Ceramic Purple Sanding Bands and Discs Made in USA. 3M’s Ceramic Purple Abrasives are excellent for sanding and finishing wood, metals, fiberglass, diestone, plastics, and other materials! 3M’s Cubitron ceramic aluminum oxide mineral sharpens itself with use. Once initial grinding wears the grain flat, it fractures along micro cracks creating new cutting edges. This process repeats itself throughout the entire grinding process. TM
2 to 4 times longer abrasive life than traditional aluminum oxide bands and discs • Faster stock removal with less heat and loading • Available in 60, 80, 120, and 220 grit •
Use Sanding Bands with 3/32″ (2.35mm), 1/8″, 1/4″ & 6mm shank rubber drum mandrels. • Use PSA Sanding Discs (pressure sensitive adhesive) on disc mandrels in 3/4″, 2″ and 3″ (19, 51, & 76mm) diameters. • Use Sanding Discs with 1/16″ arbor holes on 1/8″ & 3/32″ (2.35mm) shank mandrels. See Mandrels on pages 21-23. *Optimum Operating Speeds are much lower (between 25%–50% of maximum speeds) and also depend on the type of workpiece. •
1/2″ x 1/2″ band
7/8″ disc 3/4″ x 11⁄2″ band
3/4″ PSA disc
Ceramic Purple Sanding Bands Priced/10Pk Grit
Part No. Priced/10-Pack
6
Mandrels
1/2″ x 1″ band
2″ PSA disc
Max Speed (RPM’s)
1/4″ D x 1/2″ L (6 x 13mm) 60 80 120 220
A-4912-10 $3.30 A-SD324 A-4913-10 A-SD184 40,000 A-4914-10 A-4916-10 Assortment AK4910 $3.90 (3 ea. of 4 grits)
6
1/2″ D x 1/2″ L (13 x 13mm) 60 80 120 220
A-4922-10 $4.60 A-SD328 A-4923-10 40,000 A-SD188 A-4924-10 A-4926-10 Assortment AK4920 $5.60 (3 ea. of 4 grits)
6
1/2″ D x 1″ L (13 x 25mm) 60 80 120 220
A-4932-10 $6.80 A-4933-10 A-SD141 20,000 A-4934-10 A-SD661 A-4936-10 Assortment AK4930 $8.20 (3 ea. of 4 grits)
6
Packaging
Ceramic Purple Sanding Discs Part No.
Grit
Ceramic Purple Bands and Discs, along with Flex Diamond and Aluminum Oxide, come packed in clear plastic bags with printed header cards.
Ceramic Purple Band and Disc Assortment Kits
Priced/50-Pack
Mandrels/ Max Speed (RPM’s)
7/8″ (22mm) Discs with 1/16″ arbor hole 60 A-5672-50 $16.30 A-M1, A-M6 80 A-5673-50 7.80 120 A-5674-50 7.80 40,000 220 A-5675-50 7.80 Assortment AK5670 $9.50 (10 ea. of 60, 80, 220 grit & 20 of 120 grit)
3/4″ (19mm) PSA Discs Priced/50Pk 60 80 120 220
A-5662-50 $14.10 A-M4 A-5663-50 7.60 15,000 A-5664-50 7.60 A-5665-50 7.60 Assortment AK5660 $8.40 (10 ea. of 60, 80, 220 grit
6
6
& 20 of 120 grit)
3/4″ D x 1/2″ L (19 x 13mm)
2″ (51mm) PSA Discs Priced Each & 10Pks
A-4962-10 $6.30 A-4963-10 A-SD189 15,000 A-4964-10 A-SD143 A-4966-10 Assortment AK4960 $7.60 (3 ea. of 4 grits)
60 80 120 220
60 80 120 220
6
3/4″ D x 11⁄2″ L (19 x 38mm) 60 80 120 220
A-4942-10 $13.70 A-4943-10 A-SD145 10,000 A-4944-10 A-SD345 A-4946-10 Assortment AK4940 $16.40 (3 ea. of 4 grits)
AK2417 $47.80 141-Pc Includes 36 Bands in 60, 80, 120, and 220 grits; 100 Discs in 60, 80, 120, and 220 grits; 5 Mandrels with 1/8″ Shanks: A-SD184, A-SD188, and A-SD189 for bands, A-M4 disc mandrel and A-M6 mandrel with arbor screw.
6
A-5682 $1.10 A-5683 A-5684 A-5685 Assortment AK5680
6
A-5682-10 $10.20 A-M338, A-5683-10 A-M33 A-5684-10 10,000 A-5685-10 $3.70 (1 of each grit)
6
3″ (76mm) PSA Discs Priced Each & 10Pks A-5692 $2.50 A-5693 A-5694 A-5695 Assortment AK5690 60 80 120 220
A-5692-10 $21.00 A-M34 A-5693-10 A-5694-10 10,000 A-5695-10 $7.40 (1 of each of grit)
1″ D x 1″ L (25 x 25mm) A-4952-10 $10.60 A-4953-10 A-SD147 10,000 A-4954-10 A-4956-10 Assortment AK4950 $12.60 (3 ea. of 4 grits) 60 80 120 220
6
AK2431 $24.70 77-Pc
1″ D x 2″ L (25 x 51mm) 60 80 120 220
A-4972-10 $20.00 A-4973-10 A-SD148 A-4974-10 A-4976-10 Assortment AK4970 $23.90 (3 ea. of 4 grits)
12
10,000
Includes 24 Bands in 60, 80, 120, and 220 grits; 50 Discs in 60, 80, 120, and 220 grits; 3 Mandrels with 3/32″ Shanks: A-SD324 and A-SD328 for bands, A-M1 mandrel with arbor screw for discs.
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
3/4″ x 11⁄2″ band
3M Aluminum Oxide Sanding Bands and Discs Made in USA.
1/2″ x 1/2″ band with A-SD188 mandrel
Aluminum oxide sanding bands and discs are made of high-grade mineral and a bonding system which reduces shelling of the mineral. These economical abrasives are excellent for fast clean-up and pre-polishing work.
Aluminum Oxide Sanding Bands Part No. Grit
Price/10-Pack
6
Part No.
1/4″ D x 1/2″ L (6 x 13mm) 60 80
A-4612-10 $1.70 A-4613-10
120 A-4614-10 220 A-4616-10
6
6
60
A-5622-50
A-4613-50
80
A-5623-50
120
A-5624-50
220
A-5625-50
A-4616-50
1/2″ D x 1/2″ L (13 x 13mm)
6
60
A-4622-10 $2.20
A-4622-50 $10.50
80
A-4623-10
A-4623-50
220 A-4626-10
40,000 A-SD324 A-SD184
6
A-4624-50 A-4626-50
1/2″ D x 1″ L (13 x 25mm)
6
60
A-4632-10 $2.60
A-4632-50 $12.20
80
A-4633-10
A-4633-50
220 A-4636-10
6
A-4634-50 A-4636-50
40,000 A-SD328 A-SD188
6
60
A-4642-10 $1.80
A-4642-50 $8.50
80
A-4643-10
A-4643-50
120 A-4644-10 220 A-4646-10
6
A-4644-50 A-4646-50
20,000 A-SD141 A-SD661
6
60
A-4652-10 $2.40
A-4652-50 $11.50
80
A-4653-10
A-4653-50
120 A-4654-10 220 A-4656-10
6
A-4654-50 A-4656-50
6
40,000 A-M1 A-M6
60
A-5612-50
80
A-5613-50
3/4″ disc 1/2″ x 1″ band
120
A-5614-50
220
A-5615-50
6
$5.30 15,000 A-M4 2″ PSA disc
50pc Assortment AK5610 $5.30 (10 ea. of 60, 80, 220 grit & 20 of 120 grit)
6
Part No.
40,000 A-SD326 A-SD186
15,000 A-SD189 A-SD143
Packaging Aluminum Oxide Bands and Discs, along with Flex Diamond and Ceramic Purple, come packed in clear plastic bags with printed header cards.
6
Mandrels/ Max Speed
Price/5-Pack Price/10-Pack 2″ (51mm) PSA Discs 10,000, A-M33, A-M338
Grit
60
A-5632-5 $2.60 A-5632-10 $4.70
80
A-5633-5
220
A-5635-5
A-5633-10 A-5635-10
6pc Assortment AK5630 $2.00 (2 of each grit)
12pc Assortment AK4640 $2.10 (3 ea. of 4 grits)
3/4″ D x 1/2″ L (19 x 13mm)
$5.30
50pc Assortment AK5620 $5.30 (10 ea. of 60, 80, 220 grit & 20 of 120 grit)
Part No.
12pc Assortment AK4630 $3.10 (3 ea. of 4 grits)
3/8″ D x 1/2″ L (9.5 x 13mm)
Mandrels/ Max Speed (RPM’s)
3/4″ (19mm) PSA Discs
12pc Assortment AK4620 $2.60 (3 ea. of 4 grits)
120 A-4634-10
Price/50-Pack
A-4612-50 $8.00 A-4614-50
6
Part No. Grit
7/8″ (22mm) Discs with 1/16″ arbor hole
12pc Assortment AK4610 $2.00 (3 ea. of 4 grits)
120 A-4624-10
Aluminum Oxide Sanding Discs
Max Speed
Price/50-Pack Mandrels(RPM’s)
7/8″ disc
Cartridge Rolls and Flap Wheels Flap Wheels 1/8″ Shank $7.00 Each 35,000 RPM Max Speed Part No.
Dia.″
A-FW-1* A-FW-2*
3/4 3/4″
Width″ 3/16 3/8″
Shank″ 1/8 1/8″
Grit C-M-F C-M-F
*Specify Grit when Ordering by adding C, M, or F to Part No. C-Coarse (60 grit), M-Medium (80 grit), or F-Fine (120 grit).
12pc Assortment AK4650 $2.80 (3 ea. of 4 grits)
3/4″ D x 11⁄2″ L (19 x 38mm) 60
A-4662-10 $3.60
A-4662-50 $17.20
80
A-4663-10
A-4663-50
120 A-4664-10 220 A-4666-10
6
A-4664-50 A-4666-40
6
CRL1 10,000 A-SD145 A-SD345
12pc Assortment AK4660 $4.30 (3 ea. of 4 grits)
1″ D x 1″ L (25 x 25mm) 60
A-4672-10 $4.20
A-4672-50 $15.80
80
A-4673-10
A-4673-50
120 A-4674-10 220 A-4676-10
A-4674-50 A-4676-50
10,000 A-SD147
12pc Assortment AK4670 $5.00 (3 ea. of 4 grits)
Made in USA.
CRL2
CRL3
CRL4
CRL7
1″ Cartridge Rolls Priced/10Pk *Specify Grit when Ordering by adding C, M, or F to Part No. C-Coarse (60 grit), M-Medium (80 grit), or F-Fine (120 grit). Part No.
Roll Dia.″
Arbor Hole Dia.″
A-CRL1PK*
1/4
1/8
Price/ Shape Straight
10-Pack
Max. Speed (RPMs)
Mandrels
$3.80
15,000
A-M16
4.70
15,000
A-M16
8.50
10,000
A-M17, A-M78
A-CRL2PK*
1/2
1/8
A-CRL3PK*
3/4
3/16
A-CRL4PK*
3/8
1/8
Full Taper
9.00
15,000
A-M16
A-CRL7PK*
3/8
1/8
Half Taper
9.00
15,000
A-M16
Part Numbers and Prices are shown in red on each page. Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
13
EXL Unitized Wheels
3M Made in USA.
3M’s EXL Unitized Wheels in 1/2″, 1″ and 3″ are ideal for light deburring, oxide and fire-scale removal, cleaning, blending, and decorative finishing. They are made of non-woven fiber, coated with aluminum oxide or silicon carbide abrasive in fine, medium, or coarse grades. They run cool and should only be used dry. EXL wheels are defined by abrasive material, grade, and density or hardness. Softer densities are best for decorative finishing as they conform more readily to contour surfaces and create a more uniform finish. Harder wheels are better for more difficult blending, surface cleaning, and deburring. Recommended working speeds vary depending on the desired finish and type of metal. Slow speeds of 500 – 3,000 sfpm* are best for softer metals and composites while higher speeds of 3,700 – 8,500 sfpm* work better for harder metals. Certain speeds produce better results for specific types of operations such as high speed for blending surface imperfections. The 3″ wheels can be used on the BL Lathe with tapered spindles or the A-WM-5 and A-WM-6 wheel mandrels.
Recommended Speeds SFPM*
RPM’s for 1⁄2″ Wheel
RPM’s for 1″ Wheel
RPM’s 3″ Wheel
Decorative Finishing
500–3,000
4,000–24,000
2,000–12,000
650–4,000
Recommended Mandrels
Composites/Soft Materials
1,200–2,700
9,600–21,500
4,800–10,800
1,800–3,600
Cleaning & Conditioning
2,000–5,000
16,000–40,000
8,000–18,000
2,500–6,500
Pre-polishing
2,000–7,000
16,000–45,000
8,000–18,000
2,500–7,000
For Use with 1/2″ Wheels P/N A-M1 A-M6 Shank 3/32″ 1/8″ Arbor Screw 1/16″ 1/16″
Oxide Removal & Deburring
5,000–7,000
30,000–45,000
15,000–18,000
3,700–6,500
Blending/Polishing
3,700–8,000
30,000–45,000
15,000–18,000
5,000–7,000
Cut down prior to buffing
3,700–8,500
30,000–45,000
15,000–18,000
5,000–7,000
45,000
18,000
7,500
Maximum Speed
*Sfpm: Surface Feet Per Minute Higher speeds for 1/2″ wheels make them suitable for use with micro motors. Mid-range speeds for 1″ wheels make them suitable for use with flex shafts. Slower speeds for 3″ wheels make them suitable for use with bench lathes.
A-M13 3/32″ 1/16″
A-M15 1/8″ 1/16″
For Use with 1″ Wheels P/N A-M2 A-M14 A-M20 Shank 3/32″ 1/8″ 1/8″ Arbor Screw 1/8″ 1/8″ 1/8″ For Use with 3″ Wheels Use tapered spindle or wheel mandrel on bench lathe
Density/Hardness Abrasive Grade
Size Dia. Thick Arbor Hole
Soft ßHard 2
6
1/2″ 1/4″ 1/16″ X 1/2″ 1/8″ 1/16″
X
8
Alum. Silicon Oxide Carbide Coarse Med Fine
A/O S/C
X X X X
X X X X
F
Part No. Price Ea.
X A-5562 $2.20 X
X X X
3″ 1/2″ 1/4″
M
X X
X
1″ 1/4″ 1/8″
C
A-5567 $2.20
X A-5572 $4.20 X A-5574 $4.20 X X
A-5577 $4.20 A-5578 $4.70
X X
A-5587 $19.40 A-5588 $21.50
Mounted Polishing Buffs, Satin Finishers Made in USA. 25,000 RPM Max Speed Mounted polishing wheels and buffs provide a variety of finishes depending on compound applied (see page 18). Fine and coarse satin finishers have nylon heads impregnated with abrasive grit. Use to clean and obtain matte finishes on metal or plastic surfaces.
3/32″ (2.35mm) Shank $2.20 Each Part Numbers and Prices are shown in red on each page. A-5520 Muslin Loose 1 1/4
14
A-5533 Chamois 6 Ply 1 5/16
A-5523 Satin Finish Extra Fine 7/8 1/4
A-5517 Satin Finish Fine 7/8 1/4
A-5524 Satin Finish Coarse 7/8 1/4
Part No. Type Style Head Dia″ Head Lgth″
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
Brushes– Mounted and Unmounted Unmounted Brushes
Mounted Brush Shapes Cup
Wheel
End
Mounted Bristle Brushes 25,000 RPM Max Speed Bristle Brushes are used to clean and prepare surfaces for buffing and polishing. They are made with natural animal hair–horsehair for stiff and goat hair for soft bristles. Bristles are securely held in steel rings, evenly distributed and trimmed. The wheel, cup and end shapes will work on flat, curved, hard-to-reach surfaces. Head Dia.″
Trim Length″ Hardness
Part No.
Price Each
cup
9⁄16
5⁄32
Stiff
A-MB1
$1.60
wheel
9⁄16
1⁄8
Stiff
A-MB25
1.10
wheel
3⁄4
3⁄16
Stiff
A-MB2
1.40
end
3⁄16
1⁄4
Stiff
A-MB3
1.40
end
1/4
3/8
Stiff
A-MB35
1.30
1/8″ Shank cup
9⁄16
1⁄4
Stiff
A-MB18
$1.40
wheel
3⁄4
3⁄16
Stiff
A-MB28
1.40
wheel
3⁄4
3⁄16
Soft
A-MB238
1.60
Shape 3/32″ Shank
Mounted Steel Brushes 25,000 RPM Max Speed Steel Brushes are suitable for use on all metal surfaces for removing rust and corrosion, deburring, cleaning, edge blending, and other surface texturing and preparation. Made with .003″ and .005″ wire. Shape
Made in USA.
Head Dia.″
Trim Wire Length″ Size
Part No.
Price Each
3/32″ Shank
18,000 RPM Max Speed A-UB33 Part No.
Dia.″ Material
A-W302 Wire Size″
Hole Size″
Use with Mandrel
Price Each
A-UB33
13⁄8
Wire
.008
1/4
A-M8, A-M85
$6.50
A-W302
2
Wire
.008
1/4
A-M8, A-M85
8.00
A-W301
2
Soft Nylon N/A
3/16
A-M78,
5.90
Tapered Spindles
A-UB33 and A-W302 Steel wire brushes are used for texturing, removing rust and corrosion, edge blending and polishing of cast or machined metal surfaces or hard-to-reach areas. Soft nylon Brush A-W301 is great at very low speeds for cleaning up the “fuzzies” left over on delicate carvings without removing any of the fine detail. These unmounted accessories are used with mandrels in flex shaft handpieces or wheel mandrels on the Foredom BL Bench Lathe. The A-301 can be mounted directly onto the tapered spindle of the BL Lathe. Brushes can also be used on the discontinued Foredom High Speed Bench Grinders.
Unmounted Buffs and Abrasive Stone 18,000 RPM Max Speed A-CB1 Part No.
Material
Dia.″
A-W305 Hole Size″
A-CB1
Cotton Buff 21⁄2
Pin 1/4
end
3⁄16
1⁄4
.003
A-MB5
$1.70
A-W305
Felt Buff
wheel
3⁄4
3⁄16
.003
A-MB73
2.70
A-10072
wheel
3⁄4
3⁄16
.005
A-MB7
2.20
Aluminum 13⁄4 1/4 Oxide Grinding Stone
1/8″ Shank cup
5⁄8
1⁄4
.005
A-MB128
$2.90
end
3⁄16
1⁄4
.003
A-MB58
1.90
end
5⁄16
9⁄16
.005
A-MB538
4.80
wheel
3⁄4
3⁄16
.003
A-MB738
4.70
wheel
3⁄4
3⁄16
.005
A-MB78
3.10
wheel
1
5⁄16
.003
A-MB838
3.10
Mounted Brass Brushes 25,000 RPM Max Speed
A-301
2
A-10072
Use with Mandrel
Price Each
A-M78,Tapered Spindles $2.40 A-M8, A-M85
3.20
A-WM-3 or A-WM-4 A-WM-5 or A-WM-6 Wheel Mandrels
1.50
A-CB1 Cotton Buff can be mounted on an A-78 mandrel for use in a flex shaft handpiece. It can also mount directly onto the tapered spindle of the Foredom BL Lathe (as shown), or the spindle of discontinued B&G1 and B&G5 High Speed Bench Grinders.
Brass Brushes are suitable for use on all metal surfaces for removing rust and corrosion, deburring, cleaning, edge blending, and other surface texturing and preparation. Made with .003″ and .005″ wire. Head Dia.″
Trim Wire Length″ Size
Part No.
Price Each
end
1⁄8
1⁄4
.003
A-MB4
$1.70
wheel
3⁄4
3⁄16
.005
A-MB6
2.20
1/8″ Shank wheel
1
5⁄16
.005
A-MB68
2.80
Shape
Part Numbers and Prices are shown in red on each page.
3/32″ Shank
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
15
9/16″, 3/4″, 1″ Radial Bristle Discs
3M 9/16″ diameter with 1/16″ arbor hole 6-pack
1″ diameter with 1/8″ arbor hole
12-pack 48-pack
Price
Price
Price
$8.20
$16.30
$65.10
120 grit/white A-4522-6
A-4522-12
6-pack
12-pack
24-pack
Price
Price
Price
$9.90
$17.90
$35.20
36 grit/brown
A-4522-48
A-4532-6
A-4532-12 A-4532-24
220 grit/red A-4523-6
A-4523-12
For 9/16″, 3/4″, or 1″ discs 30,000 RPM Max Speed
A-4523-48
400 grit/blue
50 grit/green
A-4524-6
A-4533-6
A-4524-12 A-4524-48
Recommended Operating Speed for most applications is 3,000– 18,000 RPM (5,000 RPM for woodcarving)
A-4533-12 A-4533-24
Pumice (1,200 grit) pink A-4526-6
A-4526-12
A-4526-48
80 grit/yellow
6 micron (3,000 grit) peach A-4527-6
A-4527-12
A-4534-6
A-4534-12 A-4534-24
A-4527-48
1 micron (14,000 grit) light green A-4528-6
A-4528-12
A-4528-48
120 grit/white A-4535-6
3/4″ diameter 1/16″ arbor hole 6-pack
12-pack 48-pack Price
Price
$8.20
$16.30
$65.10
Price
Made in USA. Stack 6 or more discs onto a mandrel for making a sturdy brush. Discs are not used individually except when working in the most narrow of channels.
80 grit/yellow A-4511-6
A-4511-12
A-4511-48
120 grit/white A-4512-6
A-4512-12
A-4512-48
220 grit/red A-4513-6
A-4513-12 A-4513-48
A-4535-12 A-4535-24
Mandrels for use with Radial Bristle Discs Part No.
Shank
Arbor
A-M1
3/32″
1/16″
A-M2
3/32″
1/8″
A-M6
1/8″
1/16″
A-M20
1/8″
1/8″
A-M14
1/8″
1/8″
A-M15
1/8″
1/16″
9/16″
ã
Diameters 3/4″ 1″
ã
ã
ã
ã
ã
ã ã ã
400 grit/blue A-4514-6
A-4514-12
A-4514-48
Assortment Kits with Mandrels 9/16″–37-pc kit
Pumice (1,200 grit) pink A-4516-6
A-4516-12
A-4516-48
Part No. AK4520
Price $47.30
6 discs ea. of 120, 220, 400, Pumice, 6 micron, & 1 micron plus A-M1 mandrel (3/32″)
3/4″–38-pc kit
AK4510
$48.30
6 discs ea. of 80, 220, 400, Pumice, 6 micron, & 1 micron plus A-M1 (3/32″) and A-M6 (1/8″) mandrels
6 micron (3,000 grit) peach A-4517-6
A-4517-12
A-4517-48
3/4″–10-pc kit
AK4519
$14.20
3 discs ea. of 80, 400, & 6 micron plus A-M6 (1/8″) mandrel
1″– 25-pc kit
AK4530
$36.80
6 discs ea. of 36, 50, 80, & 120 grit, plus A-M20 (1/8″) mandrel
1 micron (14,000 grit) light green A-4518-6
A-4518-12
A-4518-48
1″–10-pc kit
AK4539
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
16
$19.20
3 discs ea. of 36, 80, and 120 grit, plus A-M20 (1/8″) mandrel
Scotch-Brite Radial Bristle Discs’ thin flexible bristles get into hard to reach areas without removing detail or making flat spots. 3M Cubitron™ and aluminum oxide grain embedded throughout the bristles enable them to work faster and last far longer than rubber wheels, regular brushes, buffs or conventional sanders. They generate little or no dust nor the heat associated with wheels and buffs.
For Dental Labs and Jewelers These non-contaminating discs are ideal for cleaning metal surfaces, removing light fire scale and oxide, finishing, blending, texturing, prepolishing and polishing all precious and non-precious metals, dental acrylics, flexite, and ceramics. For Woodcarvers Scotch-Brite Radial Bristle Discs are a new type of abrasive that is superior to sandpaper, flap wheels, or other types of sanders, brushes or abrasive wheels for many woodcarving and woodworking applications. Their flexible bristles can sand areas with detail, irregular, curved, or flat surfaces on soft or hard woods. Carvers can remove the “fuzzies” without harming any of the underlying detail. The coarser grits can be used to carve and texture, while the finer grits will smooth, burnish, and polish. Slower speeds allow greater flexibility & a softer touch with the bristles. Use the tips of the bristles with light pressure to extend the life of the accessory and achieve more subtle results. Higher speeds provide more aggressive material removal.
2″ and 3″ Radial Bristle Discs
3M
with 3/8″ arbor hole. Made in USA.
2″dia
3″dia
For 2″ discs 30,000 RPM Max Operating Speed
6-Pack
6-Pack
Recommended Speed for most applications is 5,000–18,000 RPM
Price
$17.30
Price
$23.60
80 grit/ yellow
For 3″ discs 20,000 RPM Max Operating Speed Recommended Speed for most applications is 5,000–18,000 RPM
80 grit/ yellow
A-4542-6
A-4552-6
2″ and 3″ Scotch-Brite Radial Bristle Discs share the same excellent properties as the smaller diameter sizes shown on the opposite page. These larger sizes get stacked onto a mandrel for use in a flex shaft handpiece or onto a special adapter for use on our BL bench lathe. When using on the lathe, Radial Bristle Discs are most effective at speeds of 5,000 to 7,000 RPM.
120 grit/ white A-4543-6
120 grit/ white A-4553-6
220 grit/ red A-4544-6
220 grit/ red
400 grit/ blue
A-4554-6
A-4545-6
Pumice 1,200 grit/ pink 400 grit/ blue
A-4546-6
A-4555-6
6 Micron 3,000 grit/ peach
3M Heavy Duty 1″ End Brushes
A-4547-6
Pumice 1,200 grit/ pink
1 Micron 14,000 grit/ light green 50 grit/ green
Mandrels & Adapters for use with 2″ & 3″ Radial Bristle Discs, End Brushes
30,000 RPM Max Speed
Part No. A-4561 (Right)
3,000– 18,000 RPM Recommended Speed Scotch-Brite Heavy Duty End Brushes are designed for finishing very hard wood, and sanding and smoothing metal. Their thicker bristles are tougher and more aggressive than the thinner and more flexible type on the other size discs. This added rigidity provides the extra industrial strength required by hard woods and metals. Use with A-4565 Roloc Mandrel.
A-4548-6
A-4501
Price Each $6.80
A-4556-6
80 grit/ yellow
A-4502
Taper Hole 3/8″
2″ ã
3″ ã
3/8″
ã
ã
A-M30 Flat Head
1/4″
ã
ã
A-M31 Screw
1/4″
A-4565 Roloc™
1/4″
Black Tapered Spindle Adapter
A-4562 (Left)
1″
6 Micron 3,000 grit/ peach A-4557-6
Grey Tapered Spindle Adapter
Shank
A-4503 120 grit/ white
Discs
ã
ã
See pgs 21-23 for complete mandrels listing & specs.
ã
1 Micron 14,000 grit/ light green A-4558-6
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
17
Ruby Carvers
Made in Switzerland. 35,000 RPM Maximum Speed
Long lasting Fine Grit Ruby Carvers, with ruby crystals firmly bonded to metal frame, provide a smooth finish on hard materials such as steel, porcelain, glass, acrylic, soft and precious metals, and wood. Standard (Coarser) Grit Ruby Carvers provide faster material removal but leave a slightly rougher finish. These are well suited for woodcarving.
2.35mm (3/32″) Shank Fine Grit A-RC15, A-RC-19, A-RC20 $10.90 Standard Grit A-RC11C – A-RC36C $13.30 Part Numbers and Prices are shown in red on each page. Dimensions Are Nominal and Slight Variations May Exist ARC15 4.5
ARC19 3.3
ARC20 4.0
4.5
8.0
10.0
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories.
AAAAAAAARC11C RC13C RC14C RC15C RC16C RC32C RC34C RC36C Part No. 8.5 6.5 7.5 7.5 6.5 5.5 5.5 5.5 Head Dia mm 16.0 19.0 7.5 12.0 12.0 10.0 10.0 13.0 Head Lgth mm
Always use a proper dust collection system or wear a respirator to prevent the inhalation of dust particles, polishing compounds, or other debris into the lungs.
Polishing Compounds Made in USA.
1
All of our polishing compounds come in standard size bars. We also offer Platinum Blue, Platinum White, and Red Rouge in small tubes that are sized and priced right for getting started with a new compound. Platinum BlueTM and Platinum WhiteTM are unique formulations that are only available from Foredom. Compound
Weight
Part No.
Price Each
AK4000 4 Bar Kit – Includes A-4001Emery, A-4002 Tripoli, A-4003 White Diamond, A-4004 Red Rouge
2 3 4 5
1 Emery (Black) Contains coarse grit to remove surface imperfections, scratches, rust, and burrs from iron, steel and other hard metals.
2 Tripoli (Brown) The most popular compound for general cutting down, scratch removal, buffing, and coloring on non-ferrous metals such as zinc die castings, brass, copper, aluminum castings and sheets.
Kit
22.25 oz.
AK4000 $11.10
Emery
6.5 oz. bar
A-4001
$2.70
Tripoli Tripoli
4.5 oz. bar 14 oz. bar
A-4002 A-5002
2.70 9.20
White Diamond Rouge 5.5 oz. bar
A-4003
2.70
White Diamond Rouge 17 oz. bar
A-5003
9.20
A-4004 A-5004 A-40041
2.70
A-4007 A-40071
6.50 2.50
5 Platinum Blue
Platinum White 5.75 oz. bar Platinum White 1 oz. tube
A-4006 A-40061
9.20 2.50
For pre-polishing and cutting down of platinum and other metals. Also for final polishing on acrylics.
Carnauba
A-4008
9.20
Red Rouge Red Rouge Red Rouge
5.75 oz. bar
Platinum Blue Platinum Blue
5 oz. bar
18
17 oz. bar 1 oz. tube
1 oz. tube
2 oz. bar
9.20 2.00
3 White Diamond Rouge Fast cutting on hard metals. Made with fine abrasive powder that produces a final satin finish on chrome, stainless steel, carbon steel, brass, and aluminum. Also use to remove rust, scale and carbon deposits on metal surfaces.
4 Red Rouge Produces a high luster on gold, silver, pewter, nickel plating and plastics for final polishing.
6 7 6 Platinum White Use for final polishing. Produces a deep luster high color final polish on platinum, gold, silver, and all metals. Also for final polishing on flexible partial material and acrylic.
7 Carnauba The hardest natural wax available. Non-tacky and highly regarded for its tough and wear resistant qualities. It is especially good for producing a high luster on wood & painted surfaces.
Felt Buffing and Polishing Accessories
Made in USA.
20,000 RPM Maximum Speed Felt Buffing and Polishing Accessories are used with compounds on hard and soft metals, metal plate, precious metals, plastics, wood, acrylic, and painted surfaces. Select the appropriate compound (see page 18) for the material being worked to produce desired finish. More About Felt: Felt is a compound carrier and the abrasives in compounds perform the actual polishing function. However, surface speed, felt hardness, applied pressure, and frictional contact determine the amount of surface removal, or polishing desired. “Cutting down” refers to a greater amount of surface removal than does “coloring”. Whether someone uses the term buffing, polishing or finishing, they typically mean a 2-step process of cutting and then coloring by which the luster or reflectiveness of a product is enhanced.
1/8″ (3.18mm) Shank Mounted Felt Bobs Priced Ea. *Please specify density when ordering by adding M, H or RH to part number.
Unmounted Felt Bobs with 1/8″ and 3/32″ arbor holes. A- C1 comes in Medium and Rock Hard densities (A-C1M or A-C1RH). A-C2M and A-C3M are ONLY available in Medium. Priced/10Pk
A-MS1* 1/2 1 $2.30
A-MS3* 1/2 1 $2.30
A-MS4* 1/2 3/4 $2.30
A-MS6* 1/2 1/2 $2.30
A-MP1* 1/4 1/4 $1.20
A-MP4* 3/8 1/2 $1.30
A-MP5* 1/2 1/2 $1.40
A-MP8* 3/4 3/4 $2.30
A-C1M (or RH) A-C2M 1/4 3/8 1/2 3/4 11.00/10 13.30/10 A-M3 (3/32) A-M7 (1/8)
A-C3M 1/2 1 19.10/10 A-M7 (1/8)
Part No. Dia″ Lgth/Thick″ Price Mandrel (Shank Size″
AKFK3 24-Pc Kit Mounted Felt Bobs 1/8″ shanks $42.00 Contains: A-MS1, A-MS3, A-MS4, A-MS6, A-MP1, A-MP4, A-MP5 and A-MP8. Each shape in Medium, Hard, and Rock Hard
Step Drills 3/32″ (2.35mm) Shank Made in Switzerland. 30,000 RPM Max Speed Individual Drills $2.20 Each Made from hardened tool steel with 3/32″ (2.35mm) shanks and an overall length of 1.8″ (45mm). Use for drilling all types of wood, precious metal, mild steel, bone, and mother of pearl. Head Dia. (D) mm in. .5 .6 .7 .9 1.0 1.1 1.4 1.5 2.0 2.2
.0197 .0236 .0276 .0354 .0394 .0433 .0551 .0591 .0787 .0866
Head Lgth (L) 8.5 8.5 8.5 8.5 8.5 10.5 10.5 11.0 11.0 11.0
Approx. Wire Size
Part No.
#76 #73 #70 #65 #61 #57 #54 #53 #47 #44
A-58005P A-58006P A-58007P A-58009P A-58010P A-58011P A-58014P A-58015P A-58020P A-58022P
NEW Diamond Twist Drill Set AK2061 20-Pc Kit $15.50
20-pc diamond coated, wire gauge twist drill set comes in plastic dispenser. These straight shank twist drills are made of high quality steel with diamond coating. Set contains one each of drills #6 to #80 (.025″ – .053″).
“D” defines head diameter. n
“L” defines head length (drilling depth).
3/32″ (2.35mm) shank
g L f
D
Part Numbers and Prices are shown in red on each page.
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
19
Cotton, Felt, Chamois Polishing Buffs
Yellow Treated Cotton Buffs
Buffs 3″ and larger are for use on tapered spindles at 5,000 RPM Max Speed. Use 1″ and 2″ buffs with an A-M78 mandrel at 20,000 RPM Maximum Speed.
Loose White Muslin Buffs
White Muslin Buffs
Made in USA.
These buffs have only one row of stitching around the arbor hole which is reinforced with leather and shellac (L/S). Made of Finex (80 x 80 weave) muslin with combed edges. The open layers provide a softer polishing action and conform to contours and curves. Use with rouge for coloring or final polishing operations.
Made with chemically treated extra fine (86 x 80) weave fabric, these buffs are stiffer than untreated ones. They will cut faster and last 2 to 3 times longer than white muslin buffs. Combed edges hold compounds without break in or combing. Center pin holes are reinforced with shellac (S) or leather and shellac (L/S).
Coarse Weave (60 x 60) Muslin have a more open weave to hold more compound. Used as a general purpose buff with cutting and polishing compounds. Combed edges do not need breaking in or combing to hold compound. The center pin holes are reinforced with shellac (S) for a tight fit on tapered mandrels and greater durability. Rows of Center Dia. Ply Stitching Hole
1″ 2″ 3″ 4″ 6″ 7″
40 40 40 40 50 50
1 1 3 3 4 4
S S S S S* S*
Part No.
Price Each
A-CBC1 A-CBC2 A-CBC3 A-CBC4 A-CBC65 A-CBC75
$1.80 1.90 2.80 3.80 6.70 8.20
*Extra thickness eliminates need for leather reinforcements.
Fine Weave (80 x 80) Finex Muslin hold compounds well but the tighter weave results in longer life. The center pin holes are reinforced with shellac (S) for a tight fit on tapered mandrels and greater durability. Combed edges do not require break in or combing to hold compound. The fine weave and stitching make them durable and especially suitable for polishing with rouge. Rows of Center Dia. Ply Stitching Hole
1″ 2″ 3″ 4″ 4″
40 40 40 40 50
1 1 3
S S S
3 3
S S
Part No.
A-CBF1 A-CBF2 A-CBF3 A-CBF4 A-CBF45
Rows of Center Dia. Ply Stitching Hole Dia.
Ply
Part No.
Price Each
3″ 3″ 4″ 5″
35 40 40 50
A-LCB35 A-LCB3 A-LCB4 A-LCB5
$2.80 3.10 4.10 6.10
30
3
S
4″ 5″ 6″ 6″
40 40 40 50
3 3 4 4
S L/S L/S S
4.00 4.80
Made in USA. 25,000 RPM Max Speed Small diameter buffs mount on mandrels for use in Foredom Handpieces. A-CBF1 has a larger arbor hole for use with the A-M16 or A-M78. The other buffs work with A-M1, A-M6, A-M7, A-M13, and A-M15 mandrels. Muslin buffs are made from fine (80 x 80) weave muslin for use with all types of compounds. Felt buffs are made from wool felt. Chamois buffs are made from the finest soft pliant chamois leather. Square Edge Solid Felt Buffs A-SE4M and A-SE4H (listed far right) are made from tightly compressed, top quality wool felt. Use for polishing and lapping flat surfaces. They will hold an edge for working in angles and corners. Knife Edge Felt A-KE4 is used for polishing in grooves.
A-CBY43
$4.70
A-CBY4 A-CBY5 A-CBY6 A-CBY65-S
5.60 6.40 7.60 9.50
Cotton Buffs made with thicker, softer fabric. Excellent for final polishing with rouge on precious metals (especially good on high karat gold and silver). Center pin holes are reinforced with shellac (S) for a tight fit on tapered mandrels.
are made with chemically treated (86 x 80 weave) muslin for added stiffness and longer life. The additional stitching and leather and shellac (L/S) centers keep wheels stiff while in use. Used for cutting and polishing in grooves, crevices, and inside curves. * Number of layers at center. All buffs are 12 ply at outside edge.
Price Each
$2.00 2.00 3.10
Price Each
Razor Edge Yellow Treated Buffs (Soft)
Flannel (Canton) Buffs
Rows of Center Dia. Ply Stitching Hole
3″ 3″ 4″ 6″
20 30 30 30
2 2
S S
3 4
S S
Part No.
Price Each
A-CFB32 A-CFB3 A-CFB4 A-CFB6
$3.90 3.80 4.70 6.70
Small Diameter Buffs for Use in Handpieces Cotton
Chamois
Felt
Knife Edge
Part No.
Price Each
2
A-CB2
$1.10
2
A-CBF1
2.00
Dia. Thick
Rows of Ply Stitching
1″
3/16″
16
1″
3/8″
40
1″
1/2″
40
2
A-CBC1 1.80
1″
1/4″
5
1(chamois) A-CLB1
3.10
16
3
2.00
1 / ″ 3/16″ 1 2
A-CB12
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
20
4″
Part No.
Dia.
Ply*
Center Hole
3″ 4″ 6″
28 28 36
L/S L/S L/S
Part No.
A-CYR3 A-CYR4 A-CYR6
Price Each
$4.70 4.50 7.90
Small Diameter Square Edge Felt Buffs– Priced/10Pk Dia.
Thick
Hardness
Part No.
1/2″ 1/8″ Medium A-SE1M 1/2″ 1/8″ Hard A-SE1H 1/2″ 1/8″ Rock Hard A-SE1RH 5/8″ 3/16″ Medium A-FB4 3/4″ 1/8″ Medium A-SE2M 3/4″ 1/8″ Hard A-SE2H 3/4″ 1/8″ Rock Hard A-SE2RH 3/4″ 1/4″ Medium A-FB3 1″ 1/8″ Medium A-SE3M 1″ 1/8″ Hard A-SE3H 1″ 1/8″ Rock Hard A-SE3RH These 3 buffs are sold individually 2″ 3/8″ Medium A-SE4M 2″ 3/8″ Hard A-SE4H 1″ knife Edge Rock Hard A-KE4RH
Price/ 10-Pk
$4.20 4.20 4.20 4.40 5.90 5.90 5.90 5.90 7.80 7.80 7.80 3.70 3.70 18.90
Screw and Tapered Mandrels, Special Adapters Made in USA and Germany. Screw-Type Mandrels Part Arbor Hole/ Overall Price No. Shank″ Capacity″ Length″ Each
A-M1
3/32
Max Speed
Maximum and Recommended Speeds vary depending on the type and size of the accessory as well as the mandrel in use. Maximum speeds shown are based on a 1″ overhang with an accessory that weighs under 1 gram and is smaller than 1/2″ in diameter. As a general rule, smaller accessories and mandrels can be used at higher speeds than larger accessories and mandrels. It is a good idea to follow the recommendations that come with both the accessory and mandrel you are using.
1/16 1-3/4 $1.10
40,000
A-M10 3/32
1/16 7/8
1.60
40,000
A-M13 3/32
1/16 1-7/8
2.10
30,000
A-M14 1/8
1/8
2.10
30,000
A-M8
1/4 1-11/16 5.20
20,000
Tapered Mandrels
A-M15 1/8
1/16 1-3/4
1.60
40,000
Part Arbor Hole/ No. Shank″ Capacity″
A-M19 1/8
1/16 1-7/8
2.10
30,000
A-M12 1/8
1/8
A-M2
3/32
1/8
1-7/8
2.70
20,000
A-M3
3/32
3/32 1-3/4
1.60
40,000
A-M6
1/8
1/16 1-3/4
1.60
40,000
A-M9
1/8
3/32 1-3/4
1.60
40,000
A-M20 1/8
1/8
1-3/4
1.60
20,000
A-M7
1/8
1/8
1-3/4
1.60
40,000
A-M83 1/8
1/8
2-1/8
2.10
20,000
A-M78 1/8
3/16 2-3/8
3.50
20,000
A-M16 1/8 1/8 2-3/4 The A-M16 and A-M17 are for use with cartridge rolls.
2.30
18,000
3.50
18,000
1/8
A-M84 1/4
1/8
1-7/8
2-1/8
2.10
20,000
A-PS83 Screwdriver $3.70
5″ long, double ended screwdriver fits many of the small size screws we use on mandrels, flex shaft motor connectors and other products. Has both flat blade and phillips tip and pocket clip.
A-M17 1/8 A-M85 1/4
A-M30 1/4
1/4
3/8
2-1/8
2.10
1-5/8
2.10
20,000
25,000
Overall Price Max Length″ Each Speed
1-3/4 $1.60
3/16 2-3/4
40,000
Tapered Spindle and FX Wheel Adapters These three adapters are used to mount accessories onto the tapered spindles of Foredom’s BL lathe. Use the A-4561 and A-4562 for 3M ScotchBrite Radial Bristle Discs and the A-4568 for mounting FX and other wheels with a 1″ hole.
10,000 RPM Max Speed Part No.
Side of Lathe
Arbor Hole″
Price Each
A-4561 Right Hand 3/8 $2.00 Side A-M31 1/4
3/8
2
3.80
25,000 A-4562 Left Hand Side
Sandpaper Split Mandrels
3/8
2.00
These mandrels have slots for inserting and wrapping small pieces of sandpaper.
20,000 RPM Max Speed Part Head No. Shank″ Dia″
Slot Lgth″ x Width″
Overall Length″
A-4568 Both Sides 1 Price Each
A-M21 3/32 1/8 3/4 x 1/32 2-3/8 $1.60 A-M22 3/32 5/32 3/4 x 1/32 2-3/8
1.60
A-M23 3/32 5/32 3/4 x 1/32 2-3/8
1.60
A-M24 3/32 3/32 3/4 x 1/64 1-3/4
1.10
A-M24LG3/32 3/32 1/2 x 1/64 2-3/16 1.10
A-M26 1/8
3/16 3/4 x 1/32 2-3/8
5.00
1.80
3M Heavy Duty End Brush Adapters The A-4565 RolocTM Adapter holds ScotchBrite Heavy Duty 1″ End Brushes.
30,000 RPM Max Speed
A-4565 1/4″ shank, 1/4″ threaded hole, 1-15/16″ overall length
$15.00
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
21
Rubber Drum Mandrels 3/32″ and 1/8″ Shank
Made in USA.
Head Dia.″
Head Length″
Total Length″
Max Speed RPM
3/32″ shank Part No.
Price Each
1/8″ shank Part No.
Price Each
1/4
1/2
1-7/8
40,000
A-SD324
$3.30
A-SD184
$3.30
1/4
1/2
2-1/4
15,000
A-SD40
3.30
–
–
3/8
1/2
1-7/8
40,000
A-SD326
3.60
A-SD186
3.60
1/2
1/2
1-7/8
40,000
A-SD328
4.00
A-SD188
4.20
3/4
1/2
1-7/8
20,000
–
–
A-SD189
3.70
1/2 1-7/8 40,000 $4.30 1/2 A-SD628 – A-SD628 is a hard plastic drum mandrel. It leaves sharp, crisp edges when used with psa polishing papers.
1/4″ Shank
Part No.
Head Dia″ x Length″
Price Each
–
Max Speed RPM
A-SD141 1/2 x 1 $5.30 20,000 2-5/8 overall length
A-SD143 3/4 x 1/2 4.20 2 overall length
20,000
A-SD144 3/4 x 1 4.30 15,000 2-1/4 overall length
A-SD145 3/4 x 1-1/2 9.00 10,000 Includes wrench. 2-3/4 overall length
6mm Shank
Part No.
Head Dia″ x Length″
Price Each
Max Speed RPM
A-SD345 3/4 x 1-1/2 $9.00 10,000 Includes wrench. 2-3/4 overall length A-SD147 1 x 1 5.80 15,000 2-3/4 overall length A-SD661 1/2 x 1
8.20 20,000
2-5/8 overall length
A-SD148 1 x 2 4.30 10,000 3-1/2 overall length
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
22
A-SD662 3/4 x 1 8.20 15,000 2-1/4 overall length
Hard Plastic Sanding Disc Mandrels Made in USA.
A-M4
A-M328
A-M338
A-M32
A-M33
A-M34
1/8 3/4 1-1/2 15,000 $4.60
1/8 1 1-5/8 15,000 5.60
1/8 2 2 10,000 8.00
1/4 1 1-3/4 15,000 5.60
1/4 2 2 10,000 7.50
1/4 3 2 10,000 8.00
Part No. Shank Dia″ Overall Length″ Max Speed RPM Price Each
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
Left Hand Threaded Mandrels 3/32″ Shank
Collet Adapters
40,000 RPM Max Speed The left handed threads on these mandrels hold accessories securely and self tighten while running in reverse operation in flex shafts and micro motors. Arbor Hole/ Capacity″
Part No.
A-M1L A-M7L
1/16 1/8
Overall Length″
1-3/4 1-3/4
Price Each
$2.10 1.60
Part No.
Shank″
Use with
Price Each
A-M50
3/32
drills 70-80
$5.80
A-M52
3/32
A-MC2
1/8
10,000 RPM Max Speed
20,000 RPM Max Speed
1/16″ shank friction grip burs 8.20 in 3/32″ (2.35mm) collet handpieces
drills 60-80
These mandrels have notches on their shanks for easy identification. A-SD324L, A-SD326L and A-SD328L also have black left hand threaded screw tops.
HPL4-3233 3/32
1/16″ shank accessories
Part No.
HPL4-3234 1/8
1/16″ shank accessories
Head Dia x Length″
16.30
10,000 RPM Max Speed
Overall Price Length″ Each
A-SD324L 1/4 x 1/2
1-3/4
6.80
HPL4-3235 3mm
3/32″ shank accessories
A-SD326L 3/8 x 1/2
1-3/4
6.80
HPL4-3236 1/8
3/32″ shank accessories
A-SD328L 1/2 x 1/2
1-3/4
6.80
HPL4-3237 3mm
1.6mm shank accessories
$16.30
NEW
Accessories for Hammer Handpieces
AK101 $75
Made in USA. 0-5,000 Strokes per Minute Max Speed.
Includes: Ball Nose, Fine Point, Square, Cylinder, Rectangle, and Bezel Rocker shown below.
6-Pc Anvil Point Kit
The six new threaded anvil points fit Foredom Flex Shaft Hammer Handpieces, Foredom Micromotor Hammer Handpiece and the Swiss made Badeco Hammer Handpiece. They are heat treated steel made to the finest specifications and finished with black oxide.
NEW Threaded Anvil Points for Hammer Flex Shaft and Micromotor Handpieces Ball Nose 3/32″ (2.35mm) dia.
HP10171
$9.00
Fine Point .015″ (.4mm) dia.
HP10172
9.00
Square 3/32″ (2.35mm)
HP10173
Cylinder 7/32″ (6mm) dia.
HP10175
12.00
Rectangle 3/32″ x 3/16″ (2.35mm x 4.8mm)
HP10176
12.00
Other Foredom Hammer Tips
Carbide Stylus HP10212 $30.50 4-48UNF-2A thread
Diamond Tip Pavé Point
Bezel Rocker 3/4″ x 3/32″ HP10179 (18mm x 2.25mm)
12.00
29.00
Flat Top Taper
H.15, H.15D, H.15SJ
HP10215 30.50 Non-threaded
H.9D PowerGraver
A-R15PT $29.00 4-48UNF-2A thread
H.15, H.15D, H.15SJ
A-R15PG 29.00 Non-threaded
H.9D PowerGraver
HP10177 $4.00 4-48UNF-2A thread
H.15, H.15D, H.15SJ
HP10177K 4.00 M3 X 0.5 thread
Micromotor Hammer MPMH-011
HP10177P 4.00 Non-threaded
H.9D PowerGraver
23
Vanadium Steel Cutters
Made in USA. 45,000 RPM Maximum Speed
These are superior quality high speed, vanadium steel cutters for shaping, grooving, slotting, and cutting in wood, plastics, & soft metals.
1/8″ (3.18mm) Shank Priced below.
Part Numbers and Prices are shown in red on each page. Dimensions are nominal and measured in inches. Slight variations may exist.
A-7101 A-7102 A-7103 A-7104 A-7105 A-7106 A-7111 A-7112 A-7113 Part No. 1/16 3/32 1/8 3/16 1/4 5/16 5/64 1/8 5/16 Head Dia″ 1/16 3/32 1/8 3/16 1/4 5/16 1/4 1/4 3/8 Head Lgth″ $7.00 7.00 7.00 8.00 9.00 9.00 7.00 7.00 9.00 Price Each
Steel Engraving Burs 2.35mm (3/32″) Shank Individual Burs $1.20 Each For etching, engraving and other fine detailing work on metal, wood, glass, ceramics and more. Made in Switzerland. 100,000 RPM Max Speed
A-7121 1/4 5/16 $9.00
A-7122 A-7131 5/16 1/4 13/32 3/8 9.00 9.00
A-7134 A-7141 1/4 1/8 3/8 3/16 9.00 7.00
A-7143 1/4 15/32 9.00
A-7145 3/8 9/16 9.00
A-7153 3/8 1/16 9.00
Part No. Head Dia″ Head Lgth″ Price Each
A-R2 1/32 1/32
A-R5 1/16 1/16
A-R7 3/32 3/32
A-P3 3/64 3/64
A-P7 3/32 5/64
Part No. Head Dia″ Head Lgth″
AK65 5-Pc Kit 3/32″ shanks $4.70 1 of each steel engraving bur
Vanadium Steel Cutters
Made in Switzerland.
35,000 RPM Max Speed Steel Cutters are suitable for all materials except hardened steel and glass. They are used for cutting grooves and countersinking in soft materials; carving and hollowing woods; slotting and grooving woods, plastics, etc.
2.35mm (3/32″) Shank Individual Cutters $10.40
A-VE2 13/64 5/16
A-VE4 9/32 7/16
A-VF2 7/32 7/16
A-VF4 1/4 17/32
A-VR2 3/16 3/16
A-VR4 9/32 9/32
A-VT2 3/16 3/8
A-VT4 Part No. 9/32 Head Dia″ 17/32 Head Lgth″
1/8″ (3.18mm) Shank Individual Cutters $6.50 Made in Germany. 35,000 RPM Max Speed
Steel Carving Drills Individual Drills $7.50 Each Tapered carving drills made of high tempered steel with three flutes. Designed for internal carving and shaping of acrylic, plastic and wood.
Made in USA. 25,000 RPM Max Speed
A-CD1 1/16
A-CD3 Part No 1/8 Dia.″
A-CD2 3/32
2.35mm Special Shape Vanadium Steel Burs $7.50 Each Head Dia mm Inch
4 5 7
A-102 3/8 3/16
A-103 5/16 3/8
A-104 5/16 7/16
A-111 Part No. 3/16 Head Dia″ Head Lgth″ 1/4
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
24
.16 .20 .28
Head Length mm Inch
9 9.5 11
.35 .37 .44
Part No. A-F040P A-F050P A-F070P
Cone–Round Fine Cut suitable for cutting and shaping on wood, plastic and non-ferrous metal. 60,000 RPM max speed.
Carbide Burs 2.35mm & 1/8″ Shanks Made in USA. 35,000 RPM Maximum Speed Typhoons have unique structurally aligned tungsten carbide points that last long and do not load quickly. Use the fine grits for general shaping and sanding. The coarse grit is for rapid and aggressive shaping and roughing out work. Typhoons are ideal for use on hard and soft woods, acrylic, die stone, plaster, hard rubber and fiberglass.
AKHK83
2.35mm (3/32″) Shank Coarse (Red) and Fine (Blue) Grit Individual Burs $16.00 Each
Ball
Long Taper
Taper
Cylinder
Ball Nose
Rotor Saw
5/16 3/16 7/16 5/16 5/16 5/16 3/4 5/8 1/2 1/2 A-KB32314 A-KB32118 A-KB32914 A-KB32518 A-KB32718 A-KB32315 A-KB32119 A-KB32915 A-KB32519 A-KB32719
3-Pc Typhoon Kit $40.00 2.35mm (3/32″) shanks Contains: A-KB32119, A-KB32719, and A-KB32913
Flame
Bud
7/16 5/16 5/16 3/16 1/2 3/4 A-KB32812 A-KB32912 A-KB32414 A-KB32813 A-KB32913 A-KB32415
Shape Head Dia.″ Head Length″
Coarse P/N Fine P/N
Part Numbers and Prices are shown in red on each page. Dimensions are nominal and shown for Fine grit burs. Coarse grit burs are slightly larger.
1/8″ (3.18mm) Shank Coarse (Red) and Fine (Blue) Grit Individual Burs $16.00 Each
AKHK84 4-Pc Typhoon Kit $55.00 1/8″ (3.18mm) shanks Contains: A-KB18119, A-KB18834, A-KB18414, and A-KB18715
Ball 5/16 5/16 A-KB18314 A-KB18315
Ball 7/16 7/16 A-KB18338 A-KB18339
Long Taper 3/16 3/4 A-KB18118 A-KB18119
Taper 5/16 1/2 A-KB18114 A-KB18115
Bud 5/16 3/4 A-KB18414 A-KB18415
Ball Nose 3/16 7/8 A-KB18718 A-KB18719
Ball Nose 5/16 1/2 A-KB18714 A-KB18715
Shape Head Dia.″ Head Length″
Coarse P/N Fine P/N
Smooth End
Rotor Saw 11/16 3/16
Flame 7/16 5/8
Dove Tail 7/16 1/2
Cylinder 5/16 1/2
Cylinder 5/16 1/2
A-KB18834 A-KB18835
A-KB18914 A-KB18915
A-KB18638 A-KB18639
A-KB18514 A-KB18515
A-KB18524 A-KB18525
Shape Head Dia.″ Head Length″
Coarse P/N Fine P/N
Typhoon burs come packed in clamshells
A-HB58 $3.90 Brass Brush (Overall–5/8″ wide x 53⁄4″ long. Bristles–3/8″ wide x 13⁄4″ long x 5/8″ high )
Typhoon Burs, Sanding Sleeves and Discs are easy to clean with the A-HB58 Brass Brush. It removes dust or chips from between rows of carbide points. Caution–Do not use a file card or steel brush to clean Typhoon burs and sleeves.
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
26
Carbide Burs 1/4″ and 6mm Shanks Made in USA. 25,000 RPM Max Speed for burs with head dias. less than 13/16″ (21mm) 10,000 RPM Max Speed for burs with head diameters 13/16″ (21mm) or larger.
1/4″ (6.4mm) Shank Coarse (Red) and Fine (Blue) Grit
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
Priced below.
Ball Nose 5/16 13⁄4 A-KB14714 A-KB14715 $18.50
Ball Nose 13/16 11⁄4 A-KB14734 A-KB14735 $20.00
Ball Nose 9/16 3/4 A-KB14712 A-KB14713 $18.50
Flame 7/8 13⁄8 A-KB14978 A-KB14979 $21.00
Flame 5/8 11⁄16 A-KB14958 A-KB14959 $20.00
Flame 3/8 3/4 A-KB14912 A-KB14913 $17.50
Shape Head Dia.″ Head Length″
Coarse P/N Fine P/N Price Each
Smooth End
Ball
Ball
Taper 15º
Taper 15º
Taper 15º
Taper 5º
7/8 7/8 A-KB14395 A-KB14396 $25.00
9/16 9/16 A-KB14312 A-KB14313 $18.50
5/16 11⁄2 A-KB14114 A-KB14115 $18.50
13/16 13⁄8 A-KB14178 A-KB14179 $20.00
9/16 1 A-KB14158 A-KB14159 $18.50
13/16 (9/16) 11⁄4 A-KB14198 N/A $20.00
Shape Head Dia.″ Head Length″
Coarse P/N Fine P/N Price Each
Smooth Ends
Cylinder 5/16 13⁄4 A-KB14514 A-KB14515 $18.50
Cylinder 13/16 11⁄4 A-KB14534 A-KB14535 $20.00
Cylinder 9/16 11⁄4 N/A A-KB14533 $18.50
Cylinder 13/16 11⁄4 A-KB14544 N/A $20.00
Cylinder 9/16 3/4 A-KB14522 N/A $18.50
Shape Head Dia.″ Head Length″
Smooth End Typhoons allow you to shape side to side without cutting into the area above the bur.
Coarse P/N Fine P/N Price Each
6.0mm Shank Coarse (Red) and Fine (Blue) Grit Priced below. Smooth Ends
Smooth Ends
A-AC1 Abrasive Cleaner $7.50 3″ x 3″ x 11/2″ Cylinder 16mm 32mm A-KB66532 A-KB66533 $20.00
Taper 15º 14mm 25mm A-KB66158 A-KB66159 $18.50
Taper 5º 21mm (15mm) 32mm A-KB66198 N/A $20.00
Taper 5º 17mm (11mm) 32mm A-KB66148 N/A $18.50
Ball Nose 21mm 32mm A-KB66734 A-KB66735 $20.00
Removes material from around the points of Typhoon burs. Also restores clogged Flex Diamond Sanding Head Dia. mm bands and discs, cartridge rolls, and Head Length mm other abrasives. Use it like a giant eraser by holding the accessory Coarse P/N against the block while running to Fine P/N remove embedded grinding debris. Price Each
Shape
27
Carbide Sanding Sleeves 1/4″ and 6mm Shanks Made in USA. 10,000 RPM Max Speed for use on Foredom’s BL and other bench lathes. Coarse Grit Shank Size
Outer Dia.″
Inside Dia.″
Length″
Mounted Part No.
Price Each
Sleeve Only Part No.
Price Each
Use on Mandrel
1/4
15/16
3/4
1/2
A-KB43525
$18.00
A-KB43524
$16.00
A-SD143
1/4
15/16
3/4
1
A-KB43545
26.50
A-KB43544
23.50
A-SD144
6mm
24mm
19mm
25mm
A-KB43546
31.00
A-KB43544
23.50
A-SD662
1/2″ and 1″ long Sanding Sleeves on Rubber Drum Mandrels.
See Pages 21-23 for complete mandrel specifications.
Fine Grit Shank Size
Outer Dia.″
Inside Dia.″
Mounted Part No.
1/4
15/16
3/4
1/2
A-KB43522
$18.00
1/4
15/16
3/4
1
A-KB43542
26.50
6mm
24mm
19mm
25mm
A-KB43543
31.00
Length″
Price Each
Price Each
Use on Mandrel
A-KB43521
$16.00
A-SD143
A-KB43541
23.50
A-SD144
A-KB43541
23.50
A-SD662
Professional Jewelers Burs
Latch Type Accessories
Made in Switzerland. 2.35mm (3/32″) Shank
Made in USA. 35,000 RPM Max Speed for Aluminum Oxide, Silicon Carbide and Vanadium Steel. 120,000 RPM Max Speed for Diamond Points
Priced per 6-Pack
Latch Type Accessories for Angle Handpieces H.55A, H.55D, H.56A, and H.56D. Aluminum Oxide (Red) $2.60 Each
Sleeve Only Part No.
Silicon Carbide (Green) $2.60 Each
Round
Inverted Cone
Size–ISO–MM Part No.–Price/6Pk
Size–ISO–MM Part No.–Price/6-Pk
5/0 005 0.50 A-23005 $6.80
5 016 1.60 A-24016 $6.80
3/0 007 0.70 A-23007 $6.80
6 018 1.80 A-24018 $6.80
2/0 008 0.80 A-23008 $6.80
ARA1 1/8 1/4 120
ARA3 5/32 9/32 120
ARA11 1/4 7/64 120
ARA12 3/16 3/16 100
ARA21 1/4 5/16 120
AAARA31 RA33 RA41 1/8 5/32 1/4 1/4 9/32 7/64 150 150 150
ARA42 3/16 3/16 120
ARA51 1/4 5/16 150
Part No.
2 012 1.20 A-23012 $6.80
Head Dia″ Head Lgth″ Grit
4 015 1.50 A-23015 $6.80
Diamond Points $3.60 Each Made in UK.
Vanadium Steel $1.30 Each
Diamonds are Medium Grit (125-180 Micron) except Extra Fine Grit A-RA76
016 1.60 5 A-23016 $6.80 020 2.00 A-23020 $6.80 8-1/2 024 2.40 A-23024 $10.10 10 027 2.70 A-23027 $10.10
A-
A-
A-
RA11R RA44 RA62
7/64 7/64
28
3/64 5/64 13/64 15/64
A-
A-
A-
RA88 RA563
RA850
3/32 7/64
3/32 15/64
5/64 15/64
A-
A-
A-
A-
RA71 RA72 RA74 RA75
2.1 1.6
2.6 2.0
2.6 7.0
1.8 4.0
ARA76
2.5 7.0
ARA77 Part No.
2.6 8.0
Head Dia″ /mm Head Lgth″/mm
11 029 2.90 A-23029 $10.10
60,000 RPM Max Speed. 3,500 - 25,000 Recommended Operating Speed Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
Bur Holders Store and organize burs, drill bits, and other accessories with various size shanks. Burs NOT included.
Bur Holder A-10082 comes in printed box.
Bur Holder A-10080 comes in printed box.
A-10082 $15.90 Rotating Bur and Tool Holder– For 1/8″ and
A-10080 $15.90 Rotating Bur Holder– Universal For All Size
1/4″ Shank Burs, Drill Bits 1/16″–5/32″. This rotating bur holder organizes up to 112 accessories. Stores: 92– 1/8″ shank and 13–1/4″ shank burs. Has 7 marked holes for drill bits 1/16″ to 5/32″. Its 3″ deep x 23/4″ dia. center cup holds small tools such as files and screwdrivers. Measures 7″ wide x 4″ high (178 x 102mm).
Shanks. This rotating bur holder stores and organizes 126 accessories including 1/16″, 3/32″, 1/8″, and 1/4″ shanks. Measures 7″ wide by 4″ high (178 x 102mm) and holds 69– 3/32″ or 1/8″ burs (in 2-step holes), 12–1/4″ burs, and 45–1/16″ burs.
A-10081 $15.90 Rotating Bur Holder– For 3/32″ (2.35mm) Burs and Small Tools. Rotating bur holder stores and organizes 114–3/32″ burs. Measures 7″ wide by 4″ high (178 x 102mm) and has a center cup (3″ deep x 23/4″ dia.) to hold small tools such as files, scribes and screwdrivers.
A-10087 $10.50 Rotating Bur Holder– For 1/16″ Friction Grip & 3/32″ (2.35mm) Burs Small in size, yet has a large storage capacity. This new rotating holder stores up to 168 accessories in two shank sizes: 90–1/16″ shank friction grip burs and 78–3/32″ shank burs. Measures 4″ wide x 2″ high (102 x 51mm).
A-10088 $3.50
A-10089 $3.50
Small Round Bur Holder– For 3/32″ (2.35mm) & 1/8″ Burs. Holds up to 48 burs with 24 holes for each size shank. Measures 21⁄8″ in dia. by 21⁄2″ high (54 x 64mm). Holds burs up to 2″ long. Includes clear cover.
Small Square Bur Holder– For 3/32″ (2.35mm) & 1/8″ Burs. Holds up to 52 burs: 34–3/32″ and 18– 1/8″ shank accessories. Measures 21⁄2″ (64mm) sq. by 21⁄4″ (54mm) high. Holds burs up to 2″ long. Includes clear cover.
Woodcarving DVD Fur, Feathers & Fins A-DVD131 3-Disc Set $31.00
Fur, Feathers & Fins is a 3 hour long, 3 project, 3-disc set with detailed instruction for novice and more experienced carvers. Master carver and teacher, Frank Russell, offers in-depth discussions of his tools, workspace, and the many steps involved in carving a Cotton Tail Rabbit, Mallard Drake Duck, and Small Mouth Bass. A rabbit pattern and sandpaper template for a split mandrel are included. A 25-min. bonus video chapter called “Foredom Basics” covers all the basics of using our tools - flex shaft set-up, operation and maintenance. Available separately and included in our K.5200, K.5400, and K.5240 Power Tool Kits for Woodcarving.
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
29
Assortment Kits We reserve the right to substitute comparable accessories when necessary. Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
37-Pc Kit $41.00
3/32″ and 1/8″ shanks 20,000 RPM Max Speed
Total Value Over $53
General Use
37-pc assortment contains steel cutters and burs, mounted points, wire and bristle brushes, rubber bonded abrasives, sanding drums and felt bobs. 20,000 RPM Max Speed
AK2446
88-Pc Kit $134.40 Total Value Over $143
AK20
3/32″ & 1/8″ shanks
General Use
AK21
General Use
34-Pc Kit $119.70
88-pc. assortment comes packed in our General Applications Kit K.2272. AK21 contains some of our most unique rotary accessories: Ceramic Purple Abrasive Bands and Discs, V StoneTM Mounted Abrasives, and CeramCut Blue® Stones. Also plated diamond points, steel cutters, aluminum oxide points, rubber bonded abrasive wheels and rods, wire and bristle brushes, felt buffs and bobs, tube of red polishing rouge, various mandrels.
AKHK10
General Use
10-Pc Kit $30.00
Total Value Over $132
10-pc assortment includes mounted abrasive aluminum oxide and silicon carbide points, carbide burs, felt bobs, sanding drum and band, 2 mandrels. 20,000 RPM Max Speed
1/8″ shanks Total Value Over $35
1/4″ shanks
2,500–10,000 RPM Recommended Speeds 34-pc assortment contains accessories for smoothing and polishing metal, wood, plastic, and acrylic. Includes a coarse grit Typhoon bur for fast stock removal, 6 each of 3M’s Scotch-Brite Radial Bristle 3″ Discs in 80, 220, 400, and 8,000 grit for smoothing, 2– 2″ cotton buffs and tubes of Platinum White and Platinum Blue compound for polishing. Also, 4 flat head and a screw mandrel with 1/4″ shanks for mounting the discs and buffs.
Total Value Over $94 1/8″ shanks
2,500– 18,000 RPM Recommended Operating Speeds Metal Only 71-pc assortment contains accessories for cutting, grinding and polishing metals. Included are 2 fiberglass reinforced cut-off wheels, 4 V Stone abrasive points for coarse grinding, 6 Ceramcut Blue Stones for fine shaping, 30 Rubber bonded rods and wheels in 3 grits, 3 each of 1/2″x1/2″ Ceramic Purple sanding bands in 60, 80, 120, and 220 grits, 9 brushes in cup, end and wheel shapes made of brass, steel and horse hair, and 2–1″ cotton buffs. Also, 5 mandrels with 1/8″ shanks and a tube of Platinum White compound.
Dental Lab
Total Value Over $114
30-pc. kit is used for polishing Valplast®, Flexite®,and other nylon denture materials. The larger diameter accessories are for mounting onto the tapered spindle of Foredom’s BL Lathe. Kit includes: 6-packs of 3″ Scotch-Brite Radial Bristle Discs in 80, 220, 400 and 8,000 grit. Also 3″ cotton buff, 2 right side and 2 left side spindle adapters and bar of platinum white polishing compound. 7,000 RPM Max Speed
30
Total Value Over $102
2,500–18,000 RPM Recommended Operating Speeds
71-Pc Kit $90.00
30-Pc Kit $104.00
50-Pc Kit $92.40
1/8″ shanks
AK2448
AK3361
Non-Metal
AK2442
50-pc assortment contains accessories for use on wood, rubber, acrylic and other non-metal materials. Included are 2 coarse grit Typhoon burs for rapid stock removal, an EXL wheel for coarse shaping, 3 each of 1/2″x 1/2″ Ceramic Purple sanding bands in 60, 80, 120, and 220 grits, 6 each of 3M’s ScotchBrite Radial Bristle 1″ Discs in 36, 50, 80, and 120 grit for final shaping, and a 1″ cotton buff and mounted felt bob for final polish. Also, 6 mandrels with 1/8″ shanks and tube of Platinum Blue compound.
Frank Russell Carving Kit AK22
Woodcarving
33-Pc Kit $299.00 Total Value Over $361 3/32″,1/8″ and 1/4″ shanks
33-pc Kit contains the burs used by Frank Russell in his 3-disc dvd set, “Fur, Feathers and Fins” (see opposite pg). According to Frank, these accessories are the ones needed to undertake any carving you can hold in your hand. Dominated by our exclusive Typhoon® carbide burs in coarse and fine grit, the kit includes 5–1/4″ shank, 8 –1/8″ shank, and 1–3/32″ shank Typhoons. The following 3/32″ shank burs are also included: 6 Ceramcut Blue Stones, 3 plated diamond points, 3 vanadium steel cutters, 1 carbide bur, 3 ruby carvers, and a sandpaper split mandrel. Also, 2″ fine bristle nylon brush with tapered mandrel and rotating bur and tool holder. 25,000 RPM Max Speed, 10,000 RPM on 1/4″ Typhoons.
Chisels for Reciprocating Power Chisels These pre-sharpened, quality made steel chisels are for use in Foredom’s H.50 reciprocating chisel handpiece, at right, and other power chisel tools, including those from Proxxon and WeCheer. The cutters have 18mm long tangs and 55mm and 75mm overall lengths–from cutting edge to end of tang. Cutters in the A-KC500 Series are 55mm and those in the A-KC700 series are 75mm long. Priced below.
#1 Chisels Single Bevel
#2 Right Skews Single Bevel
#1 x 9mm #1 x 14.5mm A-KC511 Price Each $6.95 $8.95 Length (mm) 55 55 Comes in Sets 1, 3 2, 3 Part No. A-KC509
#2 x 9mm #2 x 14mm A-KC510 A-KC512 $6.95 $8.95 55 55 1, 3 4
Fluteroni
8mm A-KC515 $8.95 55 3, 4
#8, 9, and 11 Sweeps
#9 x 9mm
#9 x 6mm
#9 x 14mm
A-KC508 Price Each $8.95 Length (mm) 55 Comes in Sets 2, 3
A-KC514 $8.95 55 4
A-KC517 $6.95 55 4
A-KC723 $9.95 75 5
A-KC505 $6.95 55 1, 3
Sets 1, 2, 4, and 5 come packed in hanging plastic case. Set 3 comes in canvas pouch
AKHK550 6-pc.
$39
A-KC503, A-KC504, A-KC505, A-KC506, A-KC509, A-KC510
Set 2
AKHK560 5-pc.
$39
A-KC501, A-KC502, A-KC507, A-KC508, A-KC511
Set 3
AK510 12-pc.
$79
A-KC501, A-KC502, A-KC503, A-KC504, A-KC505, A-KC506, A-KC507, A-KC508, A-KC509, A-KC510, A-KC511, A-KC515 in A-KC500 Canvas Pouch
Set 4
AKHK570 6-pc. $45
A-KC512, A-KC513, A-KC514, A-KC515, A-KC516, A-KC517
Set 5
#3 x 9mm A-KC503 $6.95 55 1, 3
#11 x 3.5mm 70º x 5.5mm 70º x 8mm
Chisel Sets
Set 1
12mm A-KC721 $9.95 75 5
#3 x 14mm A-KC501 $8.95 55 2, 3
#7 x 8mm A-KC504 $6.95 55 1, 3
#7 x 13mm A-KC502 $8.95 55 2, 3
#7 x 17mm A-KC718 $9.95 75 5
75º x 12mm
110º x 7mm
110º x 11mm
110º x 16mm
A-KC717 $9.95 75 5
A-KC516 $6.95 55 4
A-KC513 $8.95 55 4
A-KC722 $9.95 75 5
70º, 75º, and 110º Parting Tools
#8 x 10mm Part No.
#3 and #7 Sweeps
AKHK580 5-pc. $45
A-KC506 $6.95 55 1, 3
A-KC507 $8.95 55 2, 3
Replacement Sandpaper Belts for Belt Sander Attachment Foredom’s new Belt Sander Attachment mounts easily over the top of the H. 30 handpiece and is used to power sand and smooth metal, wood, acrylic and composite materials. The attachment includes a set of 10 belts that are also available separately as detailed below:
9/32″ x 10-1/8″ Replacement Sandpaper Belts Coarse Grits A-797415 A-797425 A-797435 AK797409
A-KC717, A-KC718, A-KC721, A-KC722, A-KC723
5 Belts 100 grit 5 Belts 180 grit 5 Belts 240 grit Coarse Assortment 9 Belts 3 ea. of 100, 180 and 240 grit
$3.50 3.50 3.50 5.00
Fine Grits
12-Pc Chisel Set (AK510) comes packed in canvas pouch. Includes chisels in Set 3. Open Canvas Pouch measures 9-3⁄4″ x 7″. Folds to 4-3⁄4″ x 3-1⁄2″. A-KC500 $15 Pouch sold separately.
A-797445 A-797455 A-797465 AK797429
5 Belts 320 grit $3.50 5 Belts 600 grit 3.50 5 Belts 1,000 grit 3.50 Fine Assortment 9 Belts 5.00 3 ea. of 320, 600 and 1,000 grit
AK797439
Coarse and Fine 18 Belts $10.00 Assortment with 3 ea. of all grits 100, 180, 240, 320, 600 and 1,000 grit
Always Wear Proper Eye Protection While Using Rotary Power Tool Accessories
31
O
ur mission is to offer the best quality and selection of rotary accessories for accomplishing what you do best— whether you’re a jeweler, woodcarver, machine shop operator, custom manufacturer, fabricator, research scientist,
lab technician, conservator, display designer, sculptor, artisan, or home shop enthusiast.
Our catalog features what you’ve come to expect from Foredom– a vast selection of items in different sizes, shapes and grits. Since quality is key, the majority of our accessories are made in the USA, and the rest come from Switzerland, Germany, Belgium, and the UK. This new edition introduces some new sanding and drilling accessories that we hope will be of interest– some less popular items have been eliminated.
Product Index
New Items Shown in Red
Page
Abrasive Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Abrasive Discs and Cut-Off Wheels . . . . . . . . . . . . . . . . . . . 7 Accessories for Hammer-Type Handpieces . . . . . . . . . . . . . 23 Aluminum Oxide Grinding Stones . . . . . . . . . . . . . . . . . . . . 7 Aluminum Oxide Points . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Aluminum Oxide Sanding Bands and Discs– 3M . . . . . . . . 13 Assortment Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Brass Cleaning Brush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Brushes– Bristle, Steel, Brass, Wire, Nylon, Tampico . . . . . . 15 Buffs– Muslin, Cotton, Felt, and Chamois . . . . . . . . . . 15, 20 Bur Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Carbide Burs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Cartridge Rolls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Carving Drills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 CeramCut Blue® Stones . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Ceramic Purple Sanding Bands and Discs– 3M . . . . . . . . . 12 Cerium Oxide Polishing Bands and Discs– 3M . . . . . . . . . . 10 Chisels (Cutters–non rotary) . . . . . . . . . . . . . . . . . . . . . . . . 31 Compounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Cut-Off Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 CW Polishing Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Diamond Hones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Diamond Points– Plated & Sintered . . . . . . . . . . . . . . . . . . . 9 Diamond Micro Finishing Film Bands and Discs– 3M . . . . 11 Diamond Twist Drills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Dressing Stones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Drills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 24 Dust Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 DVD– Fur, Feathers & Fins . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Ear Plugs– 3M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Engraving Burs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 EXL Unitized Wheels– 3M . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Felt Bobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Flap Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Flexible Diamond Sanding Bands and Discs– 3M . . . . . . . 10
Friction Grip Carbide Burs and Diamond Points . . . . . . . . . 25 ImperialTM Diamond Lapping Film Discs– 3M . . . . . . . . . . . 11 ImperialTM Diamond Microfinishing Film Discs– 3M . . . . . 11 Jewelers Burs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Latch Type Abrasive Points . . . . . . . . . . . . . . . . . . . . . . . . . 28 Mandrels, Arbors, Chucks, Adapters . . . . . . . . . . . . . . . 21-23 Plated Diamond Points and Discs . . . . . . . . . . . . . . . . . . . . . 9 Polishing Buffs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14, 20 Polishing Compounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Radial Bristle Discs– 3M . . . . . . . . . . . . . . . . . . . . . . . . 16-17 Respirator– 3M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Rubber Bonded Abrasive Wheels and Rods . . . . . . . . . . . . . 8 Ruby Carvers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Safety Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Glasses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Sandpaper Replacement Belts for Belt Sander Attachment 31 Satin Finishers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Scotch-BriteTM EXL Unitized Wheels– 3M . . . . . . . . . . . . . . 14 Scotch-BriteTM Radial Bristle Discs– 3M . . . . . . . . . . . . 16-17 Screwdriver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Silicon Carbide Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Sintered Diamond Points and Discs . . . . . . . . . . . . . . . . . . . 9 Spindle Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Steel Carving Drills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Steel Cutters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Steel Engraving Burs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Step Drills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Tape– 3M Super Bond . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Typhoon® Carbide Burs . . . . . . . . . . . . . . . . . . . . . . . . . 26-28 Typhoon® Carbide Sanding Sleeves . . . . . . . . . . . . . . . . . . 28 Vetrap Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 V StonesTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Vanadium Steel Cutters . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Wet/Dry Polishing Papers– 3M . . . . . . . . . . . . . . . . . . . . . . 11 Wet Stick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
The Foredom Electric Company
www.foredom.com
16 Stony Hill Road, Bethel, CT 06801 Tel: 203-792-8622 Fax: 203-796-7861 Email: customerservice@blackstoneind.com Accessory Catalog 350C Prices effective 11/1/09 and subject to change without notice.