1998 FORD EXPLORER Service Repair Manual

Page 1

1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

DESCRIPTION WARNING: On vehicles with air suspension, power to air suspension must be shut off before hoisting, jacking or towing. Failure to do so can result in unexpected inflation or deflation of air suspension, which can result in shifting of vehicle during servicing. Dana model 35 front axle is an integral carrier housing. See Fig. 2 . Axle housing is made of aluminum and is mounted to subframe assembly. Drive pinion depth and differential side bearing preload are set by use of shims. Pinion bearing preload is set by use of collapsible pinion spacer.

AXLE RATIO & IDENTIFICATION Axle can be identified by axle code on Safety Certification Label on left door pillar. Also, a metal identification tag, stamped with gear ratio and diameter, is attached to axle housing. See Fig. 1 . Limited-slip differential is identified by "L" on tag.

Fig. 1: Identifying Axle Tag Information Courtesy of FORD MOTOR CO. Helpmelearn November-17-07 10:45:34 10:45:31 AM

Page 1

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

Fig. 2: Exploded View Of Front Axle Housing Assembly (Typical) Courtesy of FORD MOTOR CO.

LUBRICATION Capacity is 3.25 Pts. (1.54L) of Motorcraft SAE 80W90 Thermally Stable 4X4 Axle Lubricant (XL-80W90QL). Capacities listed are approximate. Fill differential until fluid level is about 1/4" below bottom of filler plug hole.

TROUBLE SHOOTING NOTE:

See appropriate table in TROUBLE SHOOTING article in GENERAL INFORMATION.

REMOVAL & INSTALLATION WARNING: On vehicles with air suspension, power to air suspension must be shut off before hoisting, jacking or towing. Failure to do so can result in unexpected inflation or deflation of air suspension, which can result in shifting of vehicle during servicing. Helpmelearn November-17-07 10:45:31 AM

Page 2

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

AXLE SHAFT, BEARING & OIL SEAL Removal

Remove right axle shaft. See 4WD AXLE SHAFTS - FRONT - EXPLORER, MOUNTAINEER & RANGER article. Remove axle from axle housing. Using Converter Seal Remover (T94P-77001-BH) and slide hammer, remove axle tube seal. Using Bearing Remover (T94P-77001-KH) and slide hammer, remove axle tube bearing. Installation

1. Ensure bearing bore is clean and undamaged. Using Bearing Installer (T95T-1175-D) and Driver Handle (T80T-4000-W), install bearing in axle tube, .88" (44.5 mm) below outer lip of axle tube. Coat lip of seal with multipurpose grease. Using Seal Installer (T95T-3010-A) and Driver Handle (T80T-4000-W), install axle tube seal. 2. To complete installation, reverse removal procedure. Tighten all nuts and bolts or specification. See TORQUE SPECIFICATIONS . Fill differential with proper lubricant until fluid level is about 1/4" below bottom of filler plug hole. See LUBRICATION . AXLE HOUSING ASSEMBLY Removal & Installation

1. Raise and support vehicle. Remove both front axle shafts. See 4WD AXLE SHAFTS - FRONT EXPLORER, MOUNTAINEER & RANGER article. Scribe alignment marks on drive shaft and pinion flange for installation reference. Remove driveshaft-to-pinion flange bolts, and wire drive shaft aside. 2. Disconnect axle housing vent hose. Using a suitable jack, support axle housing, and secure axle housing to jack. Remove 3 front axle housing-to-frame nuts and bolts. Lower floor jack, and remove axle housing assembly. 3. To install, reverse removal procedure. Tighten all nuts and bolts to specification. See TORQUE SPECIFICATIONS . Fill differential with proper lubricant until fluid level is about 1/4" below bottom of filler plug hole. See LUBRICATION . PINION FLANGE & OIL SEAL NOTE:

Pinion flange and oil seal replacement affects bearing preload. Preload must be carefully reset during reassembly.

Removal

1. Raise and support vehicle. Scribe alignment marks on drive shaft and pinion flange for installation reference. Remove driveshaft-to-pinion flange bolts, and wire drive shaft aside. Using an INCH-lb. torque wrench, measure and record torque required to rotate pinion through several revolutions. 2. Hold pinion flange and remove pinion nut. Scribe index marks on pinion flange and pinion stem for installation reference. Remove pinion flange. Using Converter Seal Remover (T94P-77001-BH) and slide hammer, remove pinion seal. Helpmelearn November-17-07 10:45:31 AM

Page 3

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

Installation

NOTE:

If oil seal becomes cocked during installation, remove seal and install NEW oil seal.

1. Ensure pinion shaft splines are free of burrs. Remove burrs with fine crocus cloth if necessary. Lubricate area between oil seal lip. Using Pinion Oil Seal Replacer (T79P-4676-A), install oil seal into axle housing. 2. Align marks on pinion flange and pinion stem. Apply a small amount of lubricant to pinion flange splines. Install pinion flange and NEW pinion nut. Hold pinion flange, and gradually tighten nut while rotating pinion. NOTE:

If desired preload is exceeded, a NEW collapsible spacer must be installed. Tighten nut to obtain proper preload.

3. Check pinion bearing preload often, until correct preload is obtained. DO NOT back off pinion nut to reduce preload. See DIFFERENTIAL SPECIFICATIONS . Connect rear end of drive shaft to pinion flange, aligning scribed marks. 4. Apply locking compound to drive shaft bolt threads and tighten bolts to specification. See TORQUE SPECIFICATIONS . Fill differential with proper lubricant until fluid level is about 1/4" below bottom of filler plug hole. See LUBRICATION .

OVERHAUL DISASSEMBLY 1. Remove axle housing. See AXLE HOUSING ASSEMBLY under REMOVAL & INSTALLATION. Mount axle housing in Holding Fixture (T57L-500-B) using Adapters (T90T-4000-A) and Spacer (T80T4000-B2). Remove housing cover, and drain differential fluid. 2. Remove axle shaft from axle housing. Using Converter Seal Remover (T94P-77001-BH) and slide hammer, remove right and left axle tube seal. Using Bearing Remover (T94P-77001-KH) and slide hammer, remove right and left axle tube bearings (if necessary). 3. Note matched numbers or letters on differential bearing caps and carrier for reassembly reference. Remove bearing caps. Install Housing Spreader Adapter Set (T90T-4000-A) and Differential Housing Spreader (TOOL-4000-E). See Fig. 3 . Mount dial indicator onto axle housing to measure amount of spread. CAUTION: DO NOT spread carrier housing more than .030" (.76 mm), since permanent damage to housing could result. 4. Spread axle housing to .020" (.51 mm). Remove dial indicator. Carefully pry differential assembly out of housing. Remove spreader immediately so housing does not permanently distort. Remove and tag side bearing races to indicate from which side of carrier they were removed. 5. Turn nose of axle housing up. Using an INCH lbs. torque wrench, measure and record pinion bearing Helpmelearn November-17-07 10:45:31 AM

Page 4

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

preload. Hold pinion flange and remove pinion nut. Scribe index marks on pinion flange and pinion stem for installation reference. Remove pinion flange. Using Converter Seal Remover (T94P-77001-BH) and slide hammer, remove pinion seal. 6. Remove drive pinion by tapping with soft-face mallet. Remove outer pinion bearing and oil slinger. Drive out inner and outer drive pinion bearing race using Pinion Bearing Race Remover (T86T-4628-BH) and Driver Handle (T80T-4000-W). Press pinion bearing off pinion. Measure and record inner pinion bearing shim thickness. 7. Place differential case into vise, with rags underneath to protect ring gear. Remove and discard ring gear bolts. Tap ring gear with soft-face mallet to remove ring gear from case. Using drift and hammer, drive out pinion shaft lock pin. Remove pinion shaft. 8. Rotate side gears until pinion gears are aligned with case opening. Remove pinion gears and thrust washers. Remove side gears with thrust washers. Using universal bearing remover, remove inner pinion bearing and oil slinger from drive pinion.

Fig. 3: Spreading Axle Housing Courtesy of FORD MOTOR CO. CLEANING & INSPECTION Helpmelearn November-17-07 10:45:31 AM

Page 5

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

1. Clean all components in solvent. Allow bearings to air dry. Inspect all machined surfaces for smoothness or raised edges. Inspect all gear teeth for wear or chipping, and replace as necessary. 2. Check all bearings and races for nicks, roller end wear, grooves or damage. Replace as needed. Check pinion flange for wear in sealing area and replace as necessary. 3. Check differential pinion shaft, pinion gears, side gears and thrust washers for wear or damage. Replace all defective parts. Replace pinion gear and ring gear as a set. REASSEMBLY 1. Install thurst washers onto differential side gears. Install differential side greas into differential housing. Install trurst washer and pinion gear into differential case. Install pinion shaft. Install pinion shaft roll pin. 2. Using Pinion Bearing Cup Replacer (T67P-4616-A), install pinion bearing cups. If using old ring and pinion gear set, go to next step. If using new ring and pinion gear set, go to step 8 . 3. Apply a light film of oil to pinion bearing. Assemble Pinion Depth Gauge (T79P-4020-A). Install aligning adapter, gauge disc and screw. Place rear pinion bearing over aligning adapter and into bearing cup of carrier housing. See Fig. 4 . 4. Install front pinion bearing into front bearing cup. Place handle onto screw and tighten to 20 INCH lbs. (2.25 N.m). See Fig. 5 . Ensure pinion depth measuring tool is properly installed and tightened. 5. Rotate gauge block several times to seat bearings. Rotational torque on gauge block assembly should be 20 INCH lbs. (2.25 N.m) with new bearings. Final position of gauge block should be 45 degrees above axle shaft center line. See Fig. 6 . 6. Clean differential bearing bores thoroughly, and install gauge tube. Tighten differential bearing cap bolts to specification. See TORQUE SPECIFICATIONS . Use flat pinion shims as a gauge for shim selection. Hold gauge block in proper position, and measure clearance between gauge block and tube. 7. Correct shim selection is accomplished when a slight drag is felt as shim is drawn between gauge block and tube. Shims are available in various thicknesses. Install correct shim on pinion for reassembly. Pinion bearings must be installed in the same location as during pinion depth measurement. Remove measuring equipment and go to step 9 . 8. Notice the plus (+), minus (-) or zero (0) etching on both old and new pinion and adjust thickness of new shim according to charts in illustration. See Fig. 7 . Go to next step. NOTE:

If oil seal becomes cocked during installation, remove seal and install NEW oil seal.

9. Place pinion shim previously determine on pinion shaft and press on inner pinion bearing. Place NEW collapsible spacer on pinion shaft. Install outer pinion bearing and oil slinger in axle housing. Using Pinion Oil Seal Replacer (T79P-4676-A), install oil seal into axle housing. 10. Position pinion gear in axle housing. Align marks on pinion flange and pinion stem. Apply a small amount of lubricant to pinion flange splines. Install pinion flange and NEW pinion nut. Hold pinion flange, and gradually tighten nut while rotating pinion. NOTE:

If desired preload is exceeded, a NEW collapsible spacer must be installed. Tighten nut to obtain proper preload.

Helpmelearn November-17-07 10:45:31 AM

Page 6

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

11. Check pinion bearing preload often, until correct preload is obtained. DO NOT back off pinion nut to reduce preload. See DIFFERENTIAL SPECIFICATIONS . Remove differential bearing and install Right Master Bearing (T93P-4222-B) and Left Master Bearing (T93P-4222-A) on differential housing. 12. Insert differential and master bearings into axle housing. Position dial indicator to outside mounting hole. Position indicator tip on machined surface of differential case flange. Adjust dial indicator to measure full travel. Push differential case left and right as far as possible. Measure total end play and record on Line-A of differential bearing shim selection procedure work sheet. See Fig. 9 . 13. Remove differential case from carrier to install ring gear. Ensure ring is free of any nicks or burrs. Press ring gear onto case, and tighten bolts to correct torque. See TORQUE SPECIFICATIONS . Install differential case with master bearings into axle housing. 14. With dial indicator in place, push ring gear to mesh with pinion gear. Rock ring gear to allow full mesh with pinion gear. Zero dial indicator. Move ring gear away from pinion gear as much as possible. Record measurement on Line-B of differential bearing shim selection procedure work sheet. Remove differential from housing, and remove master bearing from carrier assembly. 15. Identify and mark right and left bearing for installation reference. Clamp Bearing Preload Tool (T93P4220-AR) base in a soft-jaw vise. Keep bearing mounting surface above vise jaws. Position bearing assembly on bearing preload tool base, and tighten tool bolt to 20 INCH lbs. (2.3 N.m). See Fig. 8 . 16. Invert preload tool and clamp bolt head in vise. Position depth micrometer over top of bearing. With depth micrometer positioned on bearing cone, measure height of each individual bearing assembly. Measure distance from bearing cone to bearing preload tool disc. Record both bearing measurements on Line-D on differential bearing shim selection procedure work sheet. 17. Select appropriate bearing shims using differential bearing shim selection procedure work sheet. See Fig. 9 . For correct shim, see DIFFERENTIAL SHIM SIZE table. 18. Remove master bearing from carrier, and press appropriate differential bearing on appropriate side of differential case. Tighten housing spreader so dial indicator reads .030" (.762 mm). Install selected shims. 19. Install differential assembly in axle housing. Install and tighten bearing caps to specification with housing spreader still installed. See TORQUE SPECIFICATIONS . Loosen and remove spreader. Move dial indicator base and mount in line with ring gear. 20. Mount dial indicator, and zero indicator on any ring gear drive tooth. See Fig. 10 . Turn ring gear without turning pinion gear to measure backlash. Preferred backlash is .005-008" (.127-.203 mm). 21. If backlash is not to specification, adjust backlash by increasing thickness of one shim and decreasing thickness of other shim by same amount. See RING GEAR BACKLASH-TO-SHIM THICKNESS CONVERSION table. See Fig. 11 . 22. To complete assembly, reverse disassembly procedure. Tighten all nuts and bolts to specification. See TORQUE SPECIFICATIONS . Fill differential with proper lubricant until fluid level is about 1/4" below bottom of filler plug hole. See LUBRICATION . DIFFERENTIAL SHIM SIZE Color No. Of Stripes Red 1 Red 2 Orange 1 Orange 2

Shim Thickness - In. (mm) .2410-.2415 (6.121-6.134) .2430-.2435 (6.172-6.185) .2450-.2455 (6.223-6.236) .2470-.2475 (6.274-6.287)

Helpmelearn November-17-07 10:45:31 AM

Page 7

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

Orange Orange Orange Yellow Yellow Yellow Yellow Yellow White White White White White Green Green Green Green Green Pink Pink Pink Pink Pink Blue Blue Blue Blue Gray Gray

3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 2 3 4 5 1 2

.2490-.2495 (6.325-6.337) .2510-.2515 (6.375-6.388) .2530-.2535 (6.426-6.439) .2550-.2555 (6.477-6.490) .2570-.2575 (6.528-6.541) .2590-.2595 (6.579-6.591) .2610-.2615 (6.629-6.642) .2630-.2635 (6.680-6.693) .2650-.2655 (6.731-6.744) .2670-.2675 (6.782-6.795) .2690-.2695 (6.833-6.845) .2710-.2715 (6.883-6.896) .2730-.2735 (6.934-6.947) .2750-.2755 (6.985-6.998) .2770-.2775 (7.036-7.049) .2790-.2795 (7.087-7.099) .2810-.2815 (7.137-7.150) .2830-.2835 (7.188-7.201) .2850-.2855 (7.239-7.252) .2870-.2875 (7.290-7.303) .2890-.2895 (7.341-7.353) .2910-.2915 (7.391-7.404) .2930-.2935 (7.442-7.455) .2970-.2975 (7.544-7.557) .2990-.2995 (7.595-7.607) .3010-.3015 (7.645-7.658) .3030-.3035 (7.696-7.709) .3050-.3055 (7.747-7.760) .3070-.3075 (7.798-7.811)

RING GEAR BACKLASH-TO-SHIM THICKNESS CONVERSION Required Change In Backlash - In. (mm) Required Change In Shim Thickness - In. (mm) .001 (.03) .002 (.05) .002 (.05) .002 (.05) .003 (.08) .004 (.10) .004 (.10) .006 (.15) .005 (.13) .006 (.15) .006 (.15) .008 (.20) .007 (.18) .010 (.25) .008 (.20) .010 (.25) .009 (.23) .012 (.30) Helpmelearn November-17-07 10:45:31 AM

Page 8

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

.010 (.25) .011 (.28) .012 (.30) .013 (.33) .014 (.36) .015 (.38)

.014 (.36) .014 (.36) .016 (.41) .018 (.46) .018 (.46) .020 (.51)

Fig. 4: Assembling Pinion Depth Gauge Courtesy of FORD MOTOR CO.

Helpmelearn November-17-07 10:45:31 AM

Page 9

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

Fig. 5: Installing Pinion Depth Gauge Courtesy of FORD MOTOR CO.

Helpmelearn November-17-07 10:45:31 AM

Page 10

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

Fig. 6: Final Position Of Pinion Depth Gauge Courtesy of FORD MOTOR CO.

Helpmelearn November-17-07 10:45:31 AM

Page 11

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

Fig. 7: Pinion Depth Shim Adjustment Charts Courtesy of FORD MOTOR CO.

Helpmelearn November-17-07 10:45:31 AM

Page 12

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

Fig. 8: Positioning Bearing Preload Tool Courtesy of FORD MOTOR CO.

Helpmelearn November-17-07 10:45:31 AM

Page 13

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

Fig. 9: Differential Bearing Shim Selection Procedure Work Sheet Courtesy of FORD MOTOR CO.

Helpmelearn November-17-07 10:45:31 AM

Page 14

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

Fig. 10: Checking Ring Gear Backlash Courtesy of FORD MOTOR CO.

Helpmelearn November-17-07 10:45:31 AM

Page 15

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

Fig. 11: Adjusting Ring Gear Backlash Courtesy of FORD MOTOR CO.

DIFFERENTIAL SPECIFICATIONS AXLE ASSEMBLY SPECIFICATIONS Application Ring Gear-To-Pinion Backlash

In. (mm) .005-.008 (.13-.20)

(1)

INCH Lbs. (N.m) Drive Pinion Bearing Preload New Bearings 15-35 (1.7-4.0) Used Bearings 8-14 (.9-1.6) (1) Maximum backlash variation between 3 equally spaced check points is .003" (.08 mm).

TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Drive Shaft Bolt

Ft. Lbs. (N.m) 11-15 (15-20)

Helpmelearn November-17-07 10:45:31 AM

Page 16

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Front - Dana 35 - Explorer, Mountaineer & Ranger

Front Axle Housing-To-Frame Bolt Housing Cover Bolt Ring Gear Bolt Side Bearing Cap Bolt Wheel Lug Nuts

45-59 (61-80) 20-25 (27-34) 70-89 (95-121) 47-67 (64-91) 100 (136)

Helpmelearn November-17-07 10:45:32 AM

Page 17

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

DESCRIPTION & OPERATION A half-shaft type front axle is used. Axle is of integral carrier housing, hypoid gear type. Drive pinion and ring gear bearing adjustments are all accomplished with shims. Power is transmitted through transfer case driveshaft to the drive pinion located in the axle housing. Drive pinion shaft is supported by 2 opposed tapered roller bearings. Power is transmitted from pinion gear through ring gear and differential pinion gears to axle shafts and wheels. On all models except 1999 Expedition and Navigator, a vacuum operated clutch engages front axle. 1999 Expedition and Navigator is an all wheel drive vehicle. Front axle is engaged at all time. See Fig. 1 or Fig. 2 .

Fig. 1: Exploded View Of Front Axle Housing Assembly (Except 1999 Expedition & Navigator) Courtesy of FORD MOTOR CO.

Helpmelearn November-17-07 10:46:12 10:46:09 AM

Page 1

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

Fig. 2: Exploded View Of Front Axle Housing Assembly (1999 Expedition & Navigator) Courtesy of FORD MOTOR CO.

AXLE RATIO & IDENTIFICATION Axle application can be determined through the axle code on the Safety Certification Label on left door pillar. Additionally, a metal identification tag stamped with gear ratio and diameter is secured to axle housing. See Fig. 3 .

Helpmelearn November-17-07 10:46:09 AM

Page 2

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

Fig. 3: Identifying Axle Identification Tag Courtesy of FORD MOTOR CO.

LUBRICATION Capacity is 3.5-3.7 Pts. (1.8-2.0L) of Motorcraft SAE 75W90 Thermally Stable 4X4 Axle Lubricant (XY75W90-QL). Capacities listed are approximate. Fill differential until fluid level is about 1/4" below bottom of filler plug hole.

TROUBLE SHOOTING NOTE:

See appropriate table in TROUBLE SHOOTING article in GENERAL INFORMATION.

REMOVAL & INSTALLATION WARNING: On vehicles with air suspension, power to air suspension must be shut off before hoisting, jacking or towing. Failure to do so can result in unexpected inflation or deflation of air suspension, which can result in shifting of vehicle during servicing. AXLE HOUSING ASSEMBLY Removal & Installation

NOTE:

DO NOT allow drive shaft to hang unsupported.

Helpmelearn November-17-07 10:46:09 AM

Page 3

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

1. Raise and support vehicle. Mark pinion yoke and drive shaft alignment for reassembly reference. Disconnect drive shaft from yoke, and wire aside. Remove axle shaft-to-stub axle retaining bolts and wire aside (both sides). Disconnect vent tube. Disconnect front axle actuator motor vacuum line (if equipped). 2. Using a suitable jack, support axle housing assembly and secure axle housing to jack. Remove axle housing support bracket. Remove axle housing retaining bolts. To install, reverse removal procedure. Tighten bolts to specification. See TORQUE SPECIFICATIONS table.

OVERHAUL (EXCEPT 1999 EXPEDITION & NAVIGATOR) WARNING: On vehicles with air suspension, power to air suspension must be shut off before hoisting, jacking or towing. Failure to do so can result in unexpected inflation or deflation of air suspension, which can result in shifting of vehicle during servicing. DISASSEMBLY 1. Remove axle housing. See AXLE HOUSING ASSEMBLY under REMOVAL & INSTALLATION. Drain differential fluid. Remove housing cover. Mount axle housing in Holding Fixture (T57L-500-B) using Adapters (T90T-4000-A) and Spacer (T80T-4000-B2). 2. Pull back clutch boot and remove snap ring. Remove front axle actuator motor. Remove axle housing retaining bolts and remove assembly. Remove cluster gear thrust washer. Remove front axle cluster gear. Lift front axle shift lever and remove gear selector. Remove shift lever and shift fork by removing roll pin. 3. Remove left stub axle retaining clip (inside differential assembly). Remove left stub axle. Install Housing Spreader Adapter Set (T90T-4000-A) and Differential Housing Spreader (TOOL-4000-E). See Fig. 4 . Mount dial indicator on axle housing to measure amount of spread. CAUTION: DO NOT spread axle housing more than .030" (.76 mm); permanent damage to housing could result. 4. Spread axle housing to .030" (.76 mm). Remove dial indicator. Mark bearing cap for installation reference. Remove bearing cap retaining bolts and remove bearing caps. Carefully pry differential assembly out of housing. Remove spreader immediately so housing does not permanently distort. Remove and tag side bearing races to indicate from which side of carrier they were removed. 5. Turn nose of axle housing up. Using an INCH lbs. torque wrench, measure and record pinion bearing preload. Hold pinion flange and remove pinion nut. Scribe index marks on pinion flange and pinion stem for installation reference. Remove pinion flange. Using Converter Seal Remover (T94P-77001-BH) and slide hammer, remove pinion seal. 6. Remove drive pinion by tapping with soft-faced mallet. Remove outer pinion bearing and oil slinger. Using Puller Tool (T77F-1102-A) and Slide Hammer (T50T-100-A), remove inner bearing race. If necessary, remove oil baffle. Remove pinion outer bearing race. Press pinion bearing off pinion. Measure and record inner pinion bearing shim thickness. 7. Place differential case in vise, with rags underneath to protect ring gear. Remove ring gear bolts. Tap ring gear with soft-face mallet to remove ring gear from case. Remove pinion shaft lock bolt. Remove pinion Helpmelearn November-17-07 10:46:09 AM

Page 4

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

shaft. 8. Rotate side gears until pinion gears are aligned with case opening. Remove pinion gears and thrust washers. Remove side gears with thrust washers. Remove differential case side bearings.

Fig. 4: Spreading Axle Housing Courtesy of FORD MOTOR CO. CLEANING & INSPECTION 1. Clean all components in solvent. Allow bearings to air dry. Inspect all machined surfaces for smoothness or raised edges. Inspect all gear teeth for wear or chipping and replace as necessary. 2. Check all bearings and races for nicks, roller end wear, grooves or damage. Replace as needed. Check pinion flange for wear in sealing area and replace as necessary. 3. Check differential pinion shaft, pinion gears, side gears and thrust washers for wear or damage. Replace all defective parts. Replace pinion gear and ring gear as a set. REASSEMBLY 1. Install thrust washers on differential side gears. Install differential side gears in differential housing. Helpmelearn November-17-07 10:46:09 AM

Page 5

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

2. 3. 4. 5.

6.

7.

Install thrust washer and pinion gear in differential case. Install pinion shaft. Install pinion shaft lock bolt. Install oil baffle. Using Pinion Bearing Cup Replacer (T53T-4621-C), install pinion bearing races. Apply a light film of oil on pinion bearings. Assemble Pinion Depth Gauge (T79P-4020-A). Install aligning adapter, gauge disc and screw. Place rear pinion bearing over aligning adapter and in to bearing cup of carrier housing. See Fig. 5 . Install front pinion bearing into front bearing cup. Place handle onto screw and tighten to 20 INCH lbs. (2.25 N.m). See Fig. 6 . Ensure pinion depth measuring tool is properly installed and tightened. Rotate gauge block several times to seat bearings. Rotational torque on gauge block assembly should be 20 INCH lbs. (2.25 N.m) with new bearings. Final position of gauge block should be 45 degrees above axle shaft center line. See Fig. 7 . Clean differential bearing bores thoroughly, and install gauge tube. Tighten differential bearing cap bolts to specification. See TORQUE SPECIFICATIONS . Use flat pinion shims as a gauge for shim selection. Hold gauge block in proper position, and measure clearance between gauge block and tube. Correct shim selection is accomplished when a slight drag is felt as shim is drawn between gauge block and tube. Shims are available in various thicknesses. Install correct shim on pinion for reassembly. Pinion bearings must be installed in the same location as during pinion depth measurement. Remove measuring equipment. NOTE:

If oil seal becomes cocked during installation, remove seal and install NEW oil seal.

8. Place pinion shim previously determine on pinion shaft and press on inner pinion bearing. Place NEW collapsible spacer on pinion shaft. Install outer pinion bearing and oil slinger in axle housing. Using Pinion Oil Seal Replacer (T79P-4676-A), install oil seal into axle housing. 9. Position pinion gear in axle housing. Align marks on pinion flange and pinion stem. Apply a small amount of lubricant to pinion flange splines. Install pinion flange and NEW pinion nut. Hold pinion flange, and gradually tighten nut while rotating pinion. NOTE:

If desired preload is exceeded, a NEW collapsible spacer must be installed. Tighten nut to obtain proper preload.

10. Check pinion bearing preload often, until correct preload is obtained. DO NOT back off pinion nut to reduce preload. See DIFFERENTIAL SPECIFICATIONS . Install Right Master Bearing (T93P-4222B) and Left Master Bearing (T93P-4222-A) on differential housing. 11. Insert differential and master bearings into axle housing. Position dial indicator to outside mounting hole. Position indicator tip on machined surface of differential case flange. Adjust dial indicator to measure full travel. Push differential case left and right as far as possible. Measure total end play and record on Line-A of differential bearing shim selection procedure work sheet. See Fig. 9 . 12. Remove differential case from carrier to install ring gear. Ensure ring is free of any nicks or burrs. Press ring gear onto case, and tighten bolts to correct torque. See TORQUE SPECIFICATIONS . Install differential case with master bearings into axle housing. 13. With dial indicator in place, push ring gear to mesh with pinion gear. Rock ring gear to allow full mesh with pinion gear. Zero dial indicator. Move ring gear away from pinion gear as much as possible. Record measurement on Line-B of differential bearing shim selection procedure work sheet. Remove differential Helpmelearn November-17-07 10:46:09 AM

Page 6

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

14.

15.

16. 17. 18.

19. 20.

21.

22. 23.

24.

from housing, and remove master bearing from carrier assembly. Identify and mark right and left bearing for installation reference. Clamp Bearing Preload Tool (T93P4220-AR) base in a soft-jaw vise. Keep bearing mounting surface above vise jaws. Position bearing assembly on bearing preload tool base, and tighten tool bolt to 20 INCH lbs. (2.3 N.m). See Fig. 8 . Invert preload tool and clamp bolt head in vise. Position depth micrometer over top of bearing. With depth micrometer positioned on bearing cone, measure height of each individual bearing assembly. Measure distance from bearing cone to bearing preload tool disc. Record both bearing measurements on Line-D on differential bearing shim selection procedure work sheet. Select appropriate bearing shims using differential bearing shim selection procedure work sheet. See Fig. 9 . For correct shim, see DIFFERENTIAL SHIM SIZE table. Remove master bearing from carrier, and press appropriate differential bearing on appropriate side of differential case. Tighten housing spreader so dial indicator reads .030" (.76 mm). Install selected shims. Install differential assembly in axle housing. Install and tighten bearing caps to correct torque with housing spreader still installed. See TORQUE SPECIFICATIONS . Loosen and remove spreader. Move dial indicator base and mount in line with ring gear. Mount dial indicator, and zero on any ring gear drive tooth. See Fig. 10 . Turn ring gear without turning pinion gear to measure backlash. Preferred backlash is .008-.013" (.203-.330 mm). If backlash is not to specification, adjust backlash by increasing thickness of one shim and decreasing thickness of other shim by same amount. See RING GEAR BACKLASH-TO-SHIM THICKNESS CONVERSION table. See Fig. 11 . Instal NEW "O" ring on shift lever. Position shift fork in axle housing. Lubricate "O" ring, and install shift lever. Install roll pin until flush with top of shift fork. Lift shift lever and install selector gear. Install front axle cluster gear and cluster gear thrust washer. Using Ford Black Silicone Rubber (F4AZ-19562-B), fill grove groove in axle housing and install front axle tube. Tighten axle tube retaining bolts to specification. See TORQUE SPECIFICATIONS . Install left stub axle seal. Install left stub axle and new retaining clip (inside differential assembly). Install front axle actuator motor. Using a vacuum pump, verify front axle actuator motor does not leak down. Also, ensure front axle clutch is engaging completely. To complete assembly, reverse disassembly procedure. Tighten all nuts and bolts to specifications. See TORQUE SPECIFICATIONS . Fill differential with proper lubricant until fluid level is about 1/4" below bottom of filler plug hole. See LUBRICATION .

DIFFERENTIAL SHIM SIZE Color No. Of Stripes Red 1 Red 2 Orange 1 Orange 2 Orange 3 Orange 4 Orange 5 Yellow 1 Yellow 2

Shim Thickness In. (mm) .2410-.2415 (6.121-6.134) .2430-.2435 (6.172-6.185) .2450-.2455 (6.223-6.236) .2470-.2475 (6.274-6.287) .2490-.2495 (6.325-6.337) .2510-.2515 (6.375-6.388) .2530-.2535 (6.426-6.439) .2550-.2555 (6.477-6.490) .2570-.2575 (6.528-6.541)

Helpmelearn November-17-07 10:46:09 AM

Page 7

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

Yellow Yellow Yellow White White White White White Green Green Green Green Green Pink Pink Pink Pink Pink Blue Blue Blue Blue Gray Gray

3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 2 3 4 5 1 2

.2590-.2595 (6.579-6.591) .2610-.2615 (6.629-6.642) .2630-.2635 (6.680-6.693) .2650-.2655 (6.731-6.744) .2670-.2675 (6.782-6.795) .2690-.2695 (6.833-6.845) .2710-.2715 (6.883-6.896) .2730-.2735 (6.934-6.947) .2750-.2755 (6.985-6.998) .2770-.2775 (7.036-7.049) .2790-.2795 (7.087-7.099) .2810-.2815 (7.137-7.150) .2830-.2835 (7.188-7.201) .2850-.2855 (7.239-7.252) .2870-.2875 (7.290-7.303) .2890-.2895 (7.341-7.353) .2910-.2915 (7.391-7.404) .2930-.2935 (7.442-7.455) .2970-.2975 (7.544-7.557) .2990-.2995 (7.595-7.607) .3010-.3015 (7.645-7.658) .3030-.3035 (7.696-7.709) .3050-.3055 (7.747-7.760) .3070-.3075 (7.798-7.811)

RING GEAR BACKLASH-TO-SHIM THICKNESS CONVERSION Required Change In Backlash - In. (mm) Required Change In Shim Thickness - In. (mm) .001 (.03) .002 (.05) .002 (.05) .002 (.05) .003 (.08) .004 (.10) .004 (.10) .006 (.15) .005 (.13) .006 (.15) .006 (.15) .008 (.20) .007 (.18) .010 (.25) .008 (.20) .010 (.25) .009 (.23) .012 (.30) .010 (.25) .014 (.36) .011 (.28) .014 (.36) .012 (.30) .016 (.41) .013 (.33) .018 (.46) .014 (.36) .018 (.46) Helpmelearn November-17-07 10:46:09 AM

Page 8

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

.015 (.38)

.020 (.51)

Fig. 5: Assembling Pinion Depth Gauge Courtesy of FORD MOTOR CO.

Helpmelearn November-17-07 10:46:09 AM

Page 9

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

Fig. 6: Installing Pinion Depth Gauge Courtesy of FORD MOTOR CO.

Helpmelearn November-17-07 10:46:09 AM

Page 10

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

Fig. 7: Final Position Of Pinion Depth Gauge Courtesy of FORD MOTOR CO.

Helpmelearn November-17-07 10:46:09 AM

Page 11

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

Fig. 8: Positioning Bearing Preload Tool Courtesy of FORD MOTOR CO.

Helpmelearn November-17-07 10:46:09 AM

Page 12

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

Fig. 9: Differential Bearing Shim Selection Procedure Work Sheet Courtesy of FORD MOTOR CO.

Helpmelearn November-17-07 10:46:09 AM

Page 13

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

Fig. 10: Checking Ring Gear Backlash Courtesy of FORD MOTOR CO.

Helpmelearn November-17-07 10:46:09 AM

Page 14

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

Fig. 11: Adjusting Ring Gear Backlash Courtesy of FORD MOTOR CO.

OVERHAUL (1999 EXPEDITION & NAVIGATOR) WARNING: On vehicles with air suspension, power to air suspension must be shut off before hoisting, jacking or towing. Failure to do so can result in unexpected inflation or deflation of air suspension, which can result in shifting of vehicle during servicing. DISASSEMBLY 1. Remove axle housing. See AXLE HOUSING ASSEMBLY under REMOVAL & INSTALLATION. Drain differential fluid. Remove housing cover. Mount axle housing in Holding Fixture (T57L-500-B) using Adapters (T90T-4000-A) and Spacer (T80T-4000-B2). 2. Remove axle housing retaining bolts and remove assembly. Remove coupler shaft selector gear. Remove front axle cluster gear. 3. Remove left stub axle retaining clip (inside differential assembly). Remove left stub axle. Install Housing Spreader Adapter Set (T90T-4000-A) and Differential Housing Spreader (TOOL-4000-E). See Fig. 4 . Mount dial indicator on axle housing to measure amount of spread. Helpmelearn November-17-07 10:46:09 AM

Page 15

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

CAUTION: DO NOT spread axle housing more than .030" (.76 mm); permanent damage to housing could result. 4. Spread axle housing to .030" (.76 mm). Remove dial indicator. Mark bearing cap for installation reference. Remove bearing cap retaining bolts and remove bearing caps. Carefully pry differential assembly out of housing. Remove spreader immediately so housing does not permanently distort. Remove and tag side bearing races to indicate from which side of carrier they were removed. 5. Turn nose of axle housing up. Using an INCH lbs. torque wrench, measure and record pinion bearing preload. Hold pinion flange and remove pinion nut. Scribe index marks on pinion flange and pinion stem for installation reference. Remove pinion flange. Using Converter Seal Remover (T94P-77001-BH) and slide hammer, remove pinion seal. 6. Remove drive pinion by tapping with soft-faced mallet. Remove outer pinion bearing and oil slinger. Using Puller Tool (T77F-1102-A) and Slide Hammer (T50T-100-A), remove inner bearing race. If necessary, remove oil baffle. Remove pinion outer bearing race. Press pinion bearing off pinion. Measure and record inner pinion bearing shim thickness. 7. Place differential case in vise, with rags underneath to protect ring gear. Remove ring gear bolts. Tap ring gear with soft-faced mallet to remove ring gear from case. Remove pinion shaft lock bolt. Remove pinion shaft. 8. Rotate side gears until pinion gears are aligned with case opening. Remove pinion gears and thrust washers. Remove side gears with thrust washers. Remove differential case side bearings. CLEANING & INSPECTION 1. Clean all components in solvent. Allow bearings to air dry. Inspect all machined surfaces for smoothness or raised edges. Inspect all gear teeth for wear or chipping and replace as necessary. 2. Check all bearings and races for nicks, roller end wear, grooves or damage. Replace as needed. Check pinion flange for wear in sealing area and replace as necessary. 3. Check differential pinion shaft, pinion gears, side gears and thrust washers for wear or damage. Replace all defective parts. Replace pinion gear and ring gear as a set. REASSEMBLY 1. Install thrust washers on differential side gears. Install differential side gears in differential housing. Install thrust washer and pinion gear in differential case. Install pinion shaft. Install pinion shaft lock bolt. 2. Install oil baffle. Using Pinion Bearing Cup Replacer (T53T-4621-C), install pinion bearing races. Apply a light film of oil on pinion bearings. 3. Assemble Pinion Depth Gauge (T79P-4020-A). Install aligning adapter, gauge disc and screw. Place rear pinion bearing over aligning adapter and into bearing cup of carrier housing. See Fig. 5 . 4. Install front pinion bearing into front bearing cup. Place handle onto screw and tighten to 20 INCH lbs. (2.25 N.m). See Fig. 6 . Ensure pinion depth measuring tool is properly installed and tightened. 5. Rotate gauge block several times to seat bearings. Rotational torque on gauge block assembly should be 20 INCH lbs. (2.25 N.m) with new bearings. Final position of gauge block should be 45 degrees above axle shaft center line. See Fig. 7 . 6. Clean differential bearing bores thoroughly, and install gauge tube. Tighten differential bearing cap bolts Helpmelearn November-17-07 10:46:09 AM

Page 16

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

to specification. See TORQUE SPECIFICATIONS . Use flat pinion shims as a gauge for shim selection. Hold gauge block in proper position, and measure clearance between gauge block and tube. 7. Correct shim selection is accomplished when a slight drag is felt as shim is drawn between gauge block and tube. Shims are available in various thicknesses. Install correct shim on pinion for reassembly. Pinion bearings must be installed in the same location as during pinion depth measurement. Remove measuring equipment. NOTE:

If oil seal becomes cocked during installation, remove seal and install NEW oil seal.

8. Place pinion shim previously determine on pinion shaft and press on inner pinion bearing. Place NEW collapsible spacer on pinion shaft. Install outer pinion bearing and oil slinger in axle housing. Using Pinion Oil Seal Replacer (T79P-4676-A), install oil seal into axle housing. 9. Position pinion gear in axle housing. Align marks on pinion flange and pinion stem. Apply a small amount of lubricant to pinion flange splines. Install pinion flange and NEW pinion nut. Hold pinion flange, and gradually tighten nut while rotating pinion. NOTE:

If desired preload is exceeded, a NEW collapsible spacer must be installed. Tighten nut to obtain proper preload.

10. Check pinion bearing preload often, until correct preload is obtained. DO NOT back off pinion nut to reduce preload. See DIFFERENTIAL SPECIFICATIONS . Install Right Master Bearing (T93P-4222B) and Left Master Bearing (T93P-4222-A) on differential housing. 11. Insert differential and master bearings into axle housing. Position dial indicator to outside mounting hole. Position indicator tip on machined surface of differential case flange. Adjust dial indicator to measure full travel. Push differential case left and right as far as possible. Measure total end play and record on Line-A of differential bearing shim selection procedure work sheet. See Fig. 9 . 12. Remove differential case from carrier to install ring gear. Ensure ring is free of any nicks or burrs. Press ring gear onto case and tighten bolts to correct torque. See TORQUE SPECIFICATIONS . Install differential case with master bearings into axle housing. 13. With dial indicator in place, push ring gear to mesh with pinion gear. Rock ring gear to allow full mesh with pinion gear. Zero dial indicator. Move ring gear away from pinion gear as much as possible. Record measurement on Line-B of differential bearing shim selection procedure work sheet. Remove differential from housing, and remove master bearing from carrier assembly. 14. Identify and mark right and left bearing for installation reference. Clamp Bearing Preload Tool (T93P4220-AR) base in a soft-jaw vise. Keep bearing mounting surface above vise jaws. Position bearing assembly on bearing preload tool base, and tighten tool bolt to 20 INCH lbs. (2.3 N.m). See Fig. 8 . 15. Invert preload tool and clamp bolt head in vise. Position depth micrometer over top of bearing. With depth micrometer positioned on bearing cone, measure height of each individual bearing assembly. Measure distance from bearing cone to bearing preload tool disc. Record both bearing measurements on Line-D on differential bearing shim selection procedure work sheet. 16. Select appropriate bearing shims using differential bearing shim selection procedure work sheet. See Fig. 9 . For correct shim, see DIFFERENTIAL SHIM SIZE table. 17. Remove master bearing from carrier, and press appropriate differential bearing on appropriate side of Helpmelearn November-17-07 10:46:10 AM

Page 17

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

18.

19. 20.

21.

22. 23.

differential case. Tighten housing spreader so dial indicator reads .030" (.76 mm). Install selected shims. Install differential assembly in axle housing. Install and tighten bearing caps to correct torque with housing spreader still installed. See TORQUE SPECIFICATIONS . Loosen and remove spreader. Move dial indicator base, and mount in line with ring gear. Mount dial indicator, and zero on any ring gear drive tooth. See Fig. 10 . Turn ring gear without turning pinion gear to measure backlash. Preferred backlash is .012-.015" (.304-.381 mm). If backlash is not to specification, adjust backlash by increasing thickness of one shim and decreasing thickness of other shim by same amount. See RING GEAR BACKLASH-TO-SHIM THICKNESS CONVERSION table. See Fig. 11 . Install front axle cluster gear and coupler shaft selector gear. Using Ford Black Silicone Rubber (F4AZ19562-B), fill grove groove in axle housing and install front axle tube. Tighten axle tube retaining bolts to specification. See TORQUE SPECIFICATIONS . Install left stub axle seal. Install left stub axle and NEW retaining clip (inside differential assembly). To complete assembly, reverse disassembly procedure. Tighten all nuts and bolts to specifications. See TORQUE SPECIFICATIONS . Fill differential with proper lubricant until fluid level is about 1/4" below bottom of filler plug hole. See LUBRICATION .

DIFFERENTIAL SPECIFICATIONS AXLE ASSEMBLY SPECIFICATIONS Application Differential Case Runout (Maximum) Ring Gear Runout (Maximum) Ring Gear-To-Pinion Backlash 1997-98 1999

In. (mm) .003 (.076) .004 (.10) .008-.013 (.20-.33) (1)

Drive Pinion Bearing Preload New Bearings Used Bearings (1) Preferred backlash is .012-.015 (.30-.38)

.008-.015 (.20-.38) INCH Lbs. (N.m) 16-29 (1.8-3.3) 8-14 (.9-1.6)

TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Axle Housing Mount Bolt Axle Shaft-To-Stub Axle Bolts Axle Tube Bolt Drain & Filler Plug Drive Shaft Bolts

Ft. Lbs. (N.m) 66 (89) 51-67 (69-91) 54 (73) 18 (24) 70-95 (95-129)

Helpmelearn November-17-07 10:46:10 AM

Page 18

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1997-99 DRIVE AXLES Differential - Front - 8.8" Ring Gear - Expedition, "F" Series Light Duty, Mountaineer & Navigator

Housing Cover Bolt Pinion Shaft Lock Bolt Ring Gear Bolt Side Bearing Cap Bolt

24 (33) 22 (30) 77 (104) 77 (104)

Helpmelearn November-17-07 10:46:10 AM

Page 19

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

DESCRIPTION WARNING: On vehicles with air suspension, power to air suspension must be shut off before hoisting, jacking or towing. Failure to do so can result in unexpected inflation or deflation of air suspension, which can result in shifting of vehicle during servicing. Rear axle is a hypoid-design ring and pinion gear encased in an integral cast iron axle housing. A one-piece differential case contains a conventional 2-pinion differential assembly. To signal rear anti-lock brake system operation, rear axles use an exciter ring pressed on differential case behind ring gear, and a sensor mounted in axle housing. A space is provided between ring gear and exciter ring for measuring ring gear runout.

AXLE RATIO & IDENTIFICATION NOTE:

If rear axle is a Traction-Lok version, a "L" will be displayed with the ratio. For example, a Traction-Lok axle ratio would be displayed as 3L45.

A metal tag stamped with axle model, date of manufacture, ratio, ring gear diameter and assembly plant is attached to rear cover. Use information on tag to order replacement parts. See Fig. 1 . Vehicle axle application can also be determined by axle code on Safety Certification Label located on left door pillar.

Helpmelearn November-17-07 10:46:54 10:46:51 AM

Page 1

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

Fig. 1: Identifying Rear Axle Tag Courtesy of FORD MOTOR CO.

LUBRICATION RANGER CAUTION: On models with Traction-Lok differential, add an additional 4 ozs. of Friction Modifier (C8AZ-19B546-A). Friction modifier must be added to prevent damage to differential. Capacity on vehicles without Traction-Lok differential is 5.1-5.3 Pts. (2.4-2.5L) of Motorcraft SAE 80W90 Thermally Stable Rear Axle Lubricant (XY-80W90-QL). Capacity on vehicles with Traction-Lok differential is 4.6-5.1 Pts. (2.2-2.4L) of Thermally Stable Rear Axle Lubricant (XY-80W90-QL), plus an additional 4 ozs. of Friction Modifier (C8AZ-19B546-A). Capacities listed are approximate. Fill differential until fluid level is about 1/4" below bottom of filler plug hole. EXPLORER & MOUNTAINEER (4.0L) CAUTION: On models with Traction-Lok differential, add an additional 4 ozs. of Friction Modifier (C8AZ-19B546-A). Friction modifier must be added to prevent damage to differential. Capacity on vehicles without Traction-Lok differential is 5.5-5.8 Pts. (2.6-2.7L) of Motorcraft SAE 80W90 Thermally Stable Rear Axle Lubricant (XY-80W90-QL). Capacity on vehicles with Traction-Lok differential is 5.5-5.8 Pts. (2.6-2.7L) of Motorcraft SAE 75W145 High Performance Synthetic Rear Axle Lubricant (F1TZ19580-B), plus an additional 4 ozs. of Friction Modifier (C8AZ-19B546-A). Capacities listed are approximate. Helpmelearn November-17-07 10:46:51 AM

Page 2

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

Fill differential until fluid level is about 1/4" below bottom of filler plug hole. EXPLORER & MOUNTAINEER (5.0L) Capacity is 5.5-5.8 Pts. (2.6-2.7L) of Motorcraft SAE 75W145 High Performance Synthetic Rear Axle Lubricant (F1TZ-19580-B), plus an additional 4 ozs. of Friction Modifier (C8AZ-19B546-A). Capacities listed are approximate. Fill differential until fluid level is about 1/4" below bottom of filler plug hole.

TROUBLE SHOOTING NOTE:

See appropriate table in TROUBLE SHOOTING article in GENERAL INFORMATION.

REMOVAL & INSTALLATION WARNING: On vehicles with air suspension, power to air suspension MUST be shut off before hoisting, jacking or towing. Failure to do so can result in unexpected inflation or deflation of air suspension, which can result in shifting of vehicle during these operations. AXLE SHAFT & BEARING Removal (Explorer & Mountaineer)

CAUTION: DO NOT damage "O" ring in axle shaft groove under "C" lock.

1. Raise and support vehicle. Remove wheel assemblies. Remove rear brake caliper retaining bolts, and wire caliper aside. Remove rear brake rotor. Remove housing cover, and drain lubricant. 2. Remove differential pinion shaft lock bolt and remove pinion shaft. See Fig. 2 . Push axle shaft inward and remove "C" locks. Remove axle shaft, being careful not to cut axle seal. Using a slide hammer and puller, remove bearing and oil seal as a unit.

Helpmelearn November-17-07 10:46:51 AM

Page 3

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

Fig. 2: Exploded View Of Axle Assembly (Typical) Courtesy of FORD MOTOR CO. Installation

1. Lubricate bearing with rear axle lubricant. Using a driver, install bearing. Install oil seal. If seal becomes cocked during installation, remove seal and replace with a NEW one. 2. Carefully insert axle in housing to avoid damaging oil seal. Install "C" locks, and push shafts outward to seat locks in counterbore of differential side gears. 3. Install pinion gears and thrust washers (if removed). Turn gear assembly to align pinion gear and thrust washer bores with pinion shaft holes on case. Install pinion shaft. Apply Loctite to lock bolt and tighten to specification. See TORQUE SPECIFICATIONS . 4. Clean gasket mating surfaces and apply 1/8 - 3/16" wide bead of silicone sealant on axle housing cover. Install housing cover. Tighten cover bolts to specification in a crisscross pattern. See TORQUE SPECIFICATIONS . Fill differential until fluid level is about 1/4" below bottom of filler plug hole. To complete installation, reverse removal procedures. Removal (Ranger)

CAUTION: DO NOT damage "O" ring in axle shaft groove under "C" lock.

1. Raise and support vehicle. Remove rear wheel assemblies and brake drums. Remove housing cover, and drain lubricant. Remove differential pinion shaft lock bolt and remove pinion shaft. See Fig. 2 . Push axle Helpmelearn November-17-07 10:46:51 AM

Page 4

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

shaft inward and remove "C" locks. 2. Remove axle shaft, being careful not to cut axle seal. Using a slide hammer and puller, remove bearing and oil seal as a unit. Installation

1. Lubricate bearing with rear axle lubricant. Using a driver, install bearing. Install oil seal. If seal becomes cocked during installation, remove seal and replace with a new one. 2. Carefully insert axle in housing to avoid damaging oil seal. Install "C" locks, and push shafts outward to seat locks in counterbore of differential side gears. 3. Install pinion gears and thrust washers (if removed). Turn gear assembly to align pinion gear and thrust washer bores with pinion shaft holes on case. Install pinion shaft. Apply Loctite to lock bolt and tighten to specification. See TORQUE SPECIFICATIONS . 4. Clean gasket mating surfaces and apply 1/8 - 3/16" wide bead of silicone sealant on axle housing cover. Install housing cover. Tighten cover bolts to specification in a crisscross pattern. See TORQUE SPECIFICATIONS . Fill differential until fluid level is about 1/4" below bottom of filler plug hole. To complete installation, reverse removal procedures. AXLE HOUSING ASSEMBLY Removal & Installation (Explorer & Mountaineer)

1. Raise and support vehicle. Release parking brake. Remove rear wheel assemblies. Scribe alignment marks on pinion flange and drive shaft yoke for installation reference. Remove drive shaft bolts, and wire drive shaft aside. 2. Remove brake hose junction block retaining bolt and position junction block aside. DO NOT disconnect brake lines from block. Disconnect parking brake cables at backing plates. Disengage brake lines from clips on axle housing. Disconnect rear anti-lock brake sensor harness connector. 3. Disconnect parking brake cables and rear anti-lock brake sensor harness from axle housing. Disconnect vent hose from axle housing. Disconnect anti-windup bar (if equipped). Remove brake caliper retaining bolts, and wire calipers aside. 4. Disconnect rear stabilizer bar at links. Position a suitable jack under rear axle housing, and strap housing to jack. Remove lower shock bolts. Remove "U" bolt assemblies. Remove axle housing from vehicle. To install, reverse removal procedure. Tighten nuts and bolts to specification. See TORQUE SPECIFICATIONS . Removal & Installation (1998 Ranger)

1. Raise and support vehicle. Release parking brake. Remove wheel assembly and brake drums. Disconnect parking brake cable assembly under vehicle, next to leaf spring. Secure parking brake cables to axle housing. Scribe alignment marks on pinion flange and drive shaft yoke for installation reference. 2. Remove drive shaft bolts, and wire drive shaft aside. Disconnect rear ABS sensor harness connector. Disconnect rear axle brake line and vent tube at frame. Position a suitable jack under rear axle housing, and strap housing to jack. 3. Remove lower shock bolts. Remove "U" bolt assemblies. Remove axle housing from vehicle. To install, Helpmelearn November-17-07 10:46:51 AM

Page 5

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

reverse removal procedure. Bleed brake system. Tighten nuts and bolts to specification. See TORQUE SPECIFICATIONS . Removal & Installation (1999 Ranger)

1. Raise and support vehicle. Release parking brake. Remove wheel assembly and brake drums. Scribe alignment marks on pinion flange and drive shaft yoke for installation reference. 2. Remove drive shaft bolts, and wire drive shaft aside. Disconnect rear ABS sensor harness connector. Disconnect rear brake line junction block from axle housing. DO NOT disconnect brake lines from junction block. Remove backing plate bolts, and wire backing plates aside. 3. Position a suitable jack under rear axle housing, and strap housing to jack. Remove lower shock bolts. Remove "U" bolt assemblies. Remove axle housing from vehicle. To install, reverse removal procedure. Tighten nuts and bolts to specification. See TORQUE SPECIFICATIONS . PINION FLANGE & OIL SEAL NOTE:

Pinion flange and oil seal replacement affects bearing preload. Preload must be carefully reset during reassembly.

Removal (Explorer & Mountaineer)

1. Raise and support vehicle. Remove rear wheel assemblies. Remove brake caliper retaining bolts, and wire calipers aside. Scribe alignment marks on pinion flange and drive shaft yoke for installation reference. Remove drive shaft bolts, and wire drive shaft aside. 2. Using an INCH-lb. torque wrench, measure and record torque required to rotate pinion through several revolutions. Remove and discard pinion nut. Mark pinion flange in relation to pinion shaft for installation reference. Using Puller (T77FP-4220-B1), remove pinion flange. Remove pinion seal. Installation

1. Ensure pinion shaft splines are free of burrs. Remove burrs with fine crocus cloth if necessary. Lubricate area between oil seal lip, and install oil seal into axle housing using Pinion Oil Seal Replacer (T83T4676-A). 2. Align marks on pinion flange and pinion. Apply a small amount of lubricant to pinion flange splines. Using Pinion Flange Replacer (TOOL-4858-E), install pinion flange. Hold pinion flange and gradually tighten NEW pinion nut while rotating pinion. 3. Check pinion bearing preload often, until correct preload is obtained. See DIFFERENTIAL SPECIFICATIONS . DO NOT back off pinion nut to reduce preload. 4. Connect rear end of drive shaft to pinion flange, aligning scribed marks. Tighten bolts to specification. See TORQUE SPECIFICATIONS . To complete installation, reverse removal procedures. Removal (Ranger)

1. Raise and support vehicle. Remove rear wheel assemblies. Remove rear brake drums. Scribe alignment marks on pinion flange and drive shaft yoke for installation reference. Remove drive shaft bolts, and wire Helpmelearn November-17-07 10:46:51 AM

Page 6

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

drive shaft aside. 2. Using an INCH-lb. torque wrench, measure and record torque required to rotate pinion through several revolutions. Hold pinion flange and remove pinion nut. Mark pinion flange in relation to pinion shaft for installation reference. Using Puller (T77FP-4220-B1), remove pinion flange. Remove pinion seal. Installation

NOTE:

If oil seal becomes cocked during installation, remove seal and install new oil seal.

1. Ensure pinion shaft splines are free of burrs. Remove burrs with fine crocus cloth if necessary. Lubricate area between oil seal lip, and install oil seal into axle housing using Pinion Oil Seal Replacer (T83T4676-A). 2. Align marks on pinion flange and pinion. Apply a small amount of lubricant to pinion flange splines. Using Pinion Flange Replacer (TOOL-4858-E), install pinion flange. Hold pinion flange and gradually tighten NEW pinion nut while rotating pinion. 3. Check pinion bearing preload often, until correct preload is obtained. See DIFFERENTIAL SPECIFICATIONS . DO NOT back off pinion nut to reduce preload. 4. Connect rear end of drive shaft to pinion flange, aligning scribed marks. Tighten bolts to specification. See TORQUE SPECIFICATIONS . To complete installation, reverse removal procedures. REAR ANTI-LOCK BRAKE SENSOR ASSEMBLY Removal

Rear anti-lock brake sensor is located on top of axle housing assembly. Clean area around rear anti-lock brake sensor. Disconnect harness connector. Remove retaining bolt, rear anti-lock brake sensor and "O" ring. Installation

Replace "O" ring if using original rear anti-lock brake sensor. Lubricate "O" ring with engine oil. Hold rear anti-lock brake sensor on both sides and install. DO NOT push downward on electrical connector area. Install retaining bolt and tighten to specification. See TORQUE SPECIFICATIONS . Connect harness connector. DIFFERENTIAL CASE NOTE:

Measure ring gear runout before removing differential case from axle housing. Mark bearing caps before removal. Bearing caps must be install in original position.

Removal & Installation

Remove axle shafts. See AXLE SHAFT & BEARING . Rotate differential case and visually inspect for damaged bearings and gears. Check ring gear run out. See RING GEAR RUNOUT under INSPECTION PROCEDURES. Mark bearing caps from installation reference. Remove bearing caps. Using a pry bar and a Helpmelearn November-17-07 10:46:51 AM

Page 7

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

block of wood, remove differential case. To install, reverse removal procedure.

INSPECTION PROCEDURES RING GEAR RUNOUT NOTE:

Ring gear runout should be checked before disassembling differential assembly. A space is provided between exciter ring and ring gear for measuring ring gear runout.

1. Assemble dial indicator on axle housing assembly, with tip of dial indicator contacting back face of ring gear. 2. Adjust dial indicator to zero. Rotate ring gear and note ring gear runout. Maximum ring gear runout is .004" (.10 mm). If ring gear runout exceeds .004" (.10 mm), check for improper tightening on ring gear bolts or foreign material between ring gear and differential case. 3. If ring gear runout still exceeds .004" (.10 mm), check for warped ring gear, worn differential bearings or warped differential case by checking differential case runout. See DIFFERENTIAL CASE RUNOUT . DIFFERENTIAL CASE RUNOUT 1. Remove differential case from axle housing assembly. Remove retaining bolts and ring gear. Install differential case with bearing races and preload shims into axle housing assembly. 2. Install bearing caps and retaining bolts. Tighten bearing cap retaining bolts to specification. See TORQUE SPECIFICATIONS . Rotate differential case to ensure bearings are properly seated. 3. Assemble dial indicator on axle housing assembly, with tip of dial indicator contacting ring gear surface of differential case. Adjust dial indicator to zero. 4. Rotate differential case and note differential case runout. If differential case runout is within .003" (.08 mm), install a NEW ring gear and pinion. 5. If differential case runout exceeds .003" (.08 mm), ring gear is okay. The problem area is damaged axle housing assembly or worn bearings on differential case. 6. Visually check for damaged bearings. If bearings are okay, replace both bearings and differential case. Recheck differential case runout using NEW components. 7. If differential case runout is now within .003" (.08 mm), use components for reassembly. If differential case runout exceeds .003" (.08 mm), axle housing assembly is damaged and should be replaced.

OVERHAUL WARNING: On vehicles with air suspension, power to air suspension MUST be shut off before hoisting, jacking or towing. Failure to do so can result in unexpected inflation or deflation of air suspension, which can result in shifting of vehicle during these operations. NOTE:

If vehicle is equipped with Traction-Lok, see appropriate TRACTION-LOK article.

Helpmelearn November-17-07 10:46:51 AM

Page 8

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

DISASSEMBLY 1. Raise and support vehicle. Drain lubricant and remove housing cover. Mount dial indicator and measure and record ring gear runout. See RING GEAR RUNOUT under INSPECTION PROCEDURES. Measure and record ring gear backlash. See Fig. 3 . See DIFFERENTIAL BEARING PRELOAD & RING GEAR BACKLASH under REASSEMBLY & ADJUSTMENTS. 2. Remove axle shafts. See AXLE SHAFT & BEARING under REMOVAL & INSTALLATION. Place alignment marks on drive shaft, yoke and pinion flange for reassembly reference. 3. Scribe alignment marks on pinion flange and drive shaft yoke for installation reference. Remove drive shaft bolts, and wire drive shaft aside. Mark differential bearing caps for reassembly reference and note arrow position. Loosen bearing cap bolts. Pry out differential case, bearing races and shims until loose in bearing caps. NOTE:

Bearing races and caps must be installed in original positions.

4. Remove bearing caps and differential. Remove pinion nut and pinion flange. Drive pinion out of front bearing using soft-faced hammer. Remove pinion from housing. Remove oil seal using slide hammer. NOTE:

DO NOT remove pinion bearing races unless damaged. If races are replaced, bearings must also be replaced.

5. Remove front bearing. Mount bearing puller on pinion shaft, and press shaft out of bearing. Remove, measure, and record thickness of shim located behind bearing. Remove differential side bearings with a puller. NOTE:

Tab on exciter ring must be aligned with slot in differential case.

6. Mark differential case and ring gear for reassembly reference. Remove and discard ring gear mounting bolts. Press or tap off ring gear. Remove exciter ring from differential case (if necessary). If exciter ring is removed from differential case, a NEW exciter ring must be installed. Remove pinion shaft lock bolt and remove shaft. Remove pinion gears, side gears and thrust washers.

Helpmelearn November-17-07 10:46:51 AM

Page 9

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

Fig. 3: Measuring Ring Gear Backlash Courtesy of FORD MOTOR CO. CLEANING & INSPECTION Clean all parts thoroughly in solvent. Check pinion and ring gear teeth for scoring, excessive wear, nicks and chipping. Check bearing races for deep scores or galling. Check carrier bearings for wear or damage. Replace components as necessary. Anti-Lock Brake Sensor

Check sensor pole piece for loose metal particles. Clean if necessary. Exciter Ring

Ensure exciter ring is properly pressed onto differential case. Examine ring for chips or missing teeth. Bearing Races

Check bearing races for scoring or galling. If a .0015" (.038 mm) feeler gauge can be inserted between a race and bottom of its bore at any point, race must be reseated. Helpmelearn November-17-07 10:46:51 AM

Page 10

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

Bearing & Roller Assemblies

When rotated in races, bearing rollers must turn without roughness. Check roller ends for step wear. If damaged, both parts should be replaced. Pinion Flange

Ensure flange half-rounds and lugs have not been damaged. End of flange contacting bearing, counterbore and seal surface must be smooth and free of damage. Gears

Examine pinion and ring gear teeth for scoring, excessive wear, and excessive chipping. Worn or damaged gears CANNOT be rebuilt to correct noisy condition. Axle Housing

Ensure differential and pinion bearing bores are smooth. Remove any nicks or burrs from mounting surfaces. Differential Case

Ensure hubs where bearings mount are smooth. Check differential case bearing shoulders for damage. Bearing assemblies will fail if they do not seat firmly against shoulders. Ensure differential side gears rotate freely in counterbores. REASSEMBLY & ADJUSTMENTS NOTE:

Ring and pinion gears must be replaced in matched sets.

Differential Case

1. Lubricate all parts with axle lubricant. Place side gears and thrust washers into case. Place pinion gears and thrust washers opposite each other in case openings, and in mesh with side gears. 2. Install ring gear with NEW mounting bolts. If bolts are covered with Green coating over 1/2" of threaded area, install and tighten bolts. If NEW bolts do not have Green coating, apply small amount of Loctite to bolt threads, then tighten bolts. 3. If bearing races have been replaced, NEW bearing and roller assemblies should be installed. Races must be seated in bores so a .0015" (.038 mm) feeler gauge will not fit between race and bottom of bore. Pinion Depth

1. Assemble Axle Pinion Depth Gauge Set (T79P-4020-A) and install aligning adapter, gauge disc, gauge block screw and gauge block. 2. Place rear pinion bearing over aligning disc and into bearing race of axle housing. Install front pinion bearing into front bearing race. Place tool handle onto screw and finger tighten. See Fig. 4 . 3. Ensure pinion depth measuring tools are properly installed and tightened. Apply a light film of oil to Helpmelearn November-17-07 10:46:51 AM

Page 11

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

pinion bearings. Rotate gauge block several times to seat bearings. 4. Tighten tool handle to 20 ft. lbs. (27 N.m). Final position of gauge block should be 45 degrees above axle shaft centerline. Clean differential bearing bores thoroughly and install gauge tube. Install bearing caps and bolts. Tighten bearing cap bolts to specification. See TORQUE SPECIFICATIONS . 5. Using flat pinion shims as a gauge for shim selection, hold gauge block in proper position and measure clearance between gauge block and tube. Correct shim selection is accomplished when a slight drag is felt as shim is drawn between gauge block and tube.

Fig. 4: Installing Pinion Depth Measuring Tools (Tools are included in Axle Pinion Depth Gauge Set) Courtesy of FORD MOTOR CO. Pinion Bearing Preload

1. Place pre-selected shim on pinion shaft. Press bearing onto shaft until bearing and shim are firmly seated against shoulder of shaft. Install NEW collapsible spacer on pinion shaft 2. Lubricate bearings with axle lubricant. Install front pinion bearing in housing. Install NEW pinion oil seal. Insert pinion flange into oil seal and hold firmly in place. NOTE:

If installing a NEW pinion flange, disregard scribed mark on pinion shaft.

3. From rear of axle housing, insert pinion shaft into flange. Install a NEW pinion nut on pinion shaft and Helpmelearn November-17-07 10:46:51 AM

Page 12

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

gradually tighten pinion nut while holding flange. 4. Check bearing preload often. As soon as preload is measured, turn pinion shaft in both directions several times to seat bearings. Hold pinion flange with Pinion Flange Holder (T78P-4851-A) while tightening nut. 5. Tighten pinion nut and continue to measure pinion bearing preload until the specified pinion torque is obtained. See DIFFERENTIAL SPECIFICATIONS . If bearing preload is exceeded before torque specification is reached, replace collapsible spacer. Install NEW pinion nut and repeat procedures. DO NOT loosen pinion nut to reduce pinion bearing preload. Differential Bearing Preload & Ring Gear Backlash

1. With pinion depth set and pinion installed, place differential case and gear assembly with bearings and races into axle housing. 2. Install a .265" (6.73 mm) shim on left (ring gear side) side of differential. Install left bearing cap and bolts. Tighten bolts finger tight. Select and install largest shim that will fit, with a slight drag, on pinion gear side (right side) of differential. Install right bearing cap and bolts and tighten all cap bolts to specification. See TORQUE SPECIFICATIONS e. 3. Rotate gear assembly to ensure free operation. Check ring and pinion backlash. See Fig. 3 . If backlash is .008-.015" (.20-.38 mm), proceed to step 6 . If backlash is zero, add .020" (.51 mm) to shim size on right side, and subtract .020" (.51 mm) from shim size on left side. 4. If backlash is less than .008" (.20 mm) or more than .015" (.38 mm), increase or decrease shim size where necessary to correct reading. See Fig. 5 . See BACKLASH-TO-SHIM THICKNESS CONVERSION table. 5. Retighten bearing cap bolts and rotate gear assembly several times. Recheck backlash and correct if necessary. Increase both left and right shim sizes .006" (.15 mm), and reinstall for correct preload. 6. Ensure shims are seated and gear assembly turns freely. Using marking compound, check gear tooth contact pattern. See GEAR TOOTH CONTACT PATTERNS article in GENERAL INFORMATION. BACKLASH-TO-SHIM THICKNESS CONVERSION Required Change In Backlash - In. (mm) .001 (.03) .002 (.05) .003 (.08) .004 (.10) .005 (.13) .006 (.15) .007 (.18) .008 (.20) .009 (.23) .010 (.25) .011 (.28) .012 (.30) .013 (.33)

Change In Shim Thickness - In. (mm) .002 (.05) .002 (.05) .004 (.10) .006 (.15) .006 (.15) .008 (.20) .010 (.25) .010 (.25) .012 (.30) .014 (.35) .014 (.35) .016 (.41) .018 (.46)

Helpmelearn November-17-07 10:46:51 AM

Page 13

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

.014 (.35) .015 (.38)

.018 (.46) .020 (.51)

Fig. 5: Adjusting Backlash Courtesy of FORD MOTOR CO. Final Assembly

Clean differential housing surface and apply a continuous bead of silicone sealant to housing cover. Install cover and tighten bolts to specification. See TORQUE SPECIFICATIONS . Install drive shaft. To complete assembly, reverse disassembly procedure. Fill differential until fluid level is about 1/4" below bottom of filler plug hole. Adjust brakes if required.

DIFFERENTIAL SPECIFICATIONS DIFFERENTIAL ASSEMBLY SPECIFICATIONS Application ABS Sensor Air Gap Axle Shaft End Play (Max.) Differential Case Flange Runout

Specification .005-.045" (0.127-1.143 mm) .030" (.762 mm) .003" (.08 mm)

Helpmelearn November-17-07 10:46:51 AM

Page 14

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 Drive Axles Differentials - Rear - 8.8" Ring Gear - Explorer, Mountaineer & Ranger

Maximum Backlash Variation Between Teeth Nominal Pinion Shim Thickness Pinion Gear Thrust Washer Thickness Ring Gear Back Face Runout

.004" (.10 mm) .030" (.76 mm) .030-.032" (.76-.81 mm) .004" (.10 mm) .008-.015" (.020-.038 mm)

Ring Gear Backlash (1) Side Gear Thrust Washer Thickness

.030-.032" (.76-.81 mm) INCH Lbs. (N.m)

Pinion Bearing Preload New Bearings Original Bearings (With Oil Seal) (1) Preferred setting is .012-.015" (.30-.38 mm).

16-29 (1.8-3.2) 8-14 (.9-1.6)

TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application ABS Sensor Bolt Bearing Cap Bolt 1998 1999 Driveshaft-To-Pinion Flange Bolt 1998 1999 Housing Cover Bolt 1998 1999 Oil Filler Plug 1998 1999 Pinion Shaft Lock Bolt 1998 1999 Ring Gear Bolt 1998 1999 Shock Absorber Nut (Lower) "U" Bolt Nut 1998 1999 Wheel Lug Nut

Ft. Lbs. (N.m) 25-30 (34-41) 70-85 (95-115) 77 (104) 70-95 (95-129) 83 (113) 28-38 (38-52) 33 (45) 15-30 (20-41) 22 (30) 15-30 (21-41) 22 (30) 70-85 (95-115) 77 (104) 40-60 (54-81) 65-87 (88-118) 76 (103) 100 (136)

Helpmelearn November-17-07 10:46:51 AM

Page 15

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Traction-Lok - 7.5", 8.8", 9.75" & 10.25" Ring Gear

1998-99 DRIVE AXLES Differentials - Traction-Lok - 7.5", 8.8", 9.75" & 10.25" Ring Gear

DESCRIPTION NOTE:

Differentials are identified by inside diameter of ring gear. Traction-Lok and conventional rear axle assemblies are identical except for differential case. Information in this article is related to Traction-Lok differential case overhaul. To remove differential case from rear axle housing and for all other information, see appropriate rear differential article.

NOTE:

The 10.25" differential Traction-Lok unit is also referred to as a Limited Slip Differential on 1998 models.

Traction-Lok differential has limited-slip function. See Fig. 1 . Two sets of multiple disc clutches control limited slip differential action. On 7.5" ring gear, side gear mounting distance is controlled by 7 plates on each side: 3 steel, 4 friction, and a maximum of 2 steel shims selectively fit to control side gear position. On 8.8" ring gear, side gear mounting distance is controlled by 7 plates on each side: 4 steel, 3 friction, and one steel shim selectively fit to control side gear position. On 9.75" ring gear, side gear mounting distance is controlled by 8 plates on each side: 4 steel, 4 friction, and one or more steel selective shims. Plates are stacked on side gear hubs and housed in differential case. An "S"-shaped preload spring (7.5" and 8.8") or a Belleville spring plate (9.75") between side gears applies pre-load to clutch packs.

Helpmelearn November-17-07 10:47:25 10:47:22 AM

Page 1

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Traction-Lok - 7.5", 8.8", 9.75" & 10.25" Ring Gear

Fig. 1: Exploded View Of Typical Traction-Lok Differential Courtesy of FORD MOTOR CO.

AXLE RATIO & IDENTIFICATION Axle can be identified by axle code on Safety Certification Label on left door pillar. A metal identification tag, stamped with gear ratio and ring gear diameter, is attached to rear cover bolt. DIFFERENTIAL APPLICATION Vehicle Application Explorer Expedition E Series F Series Mountaineer Navigator Ranger

Ring Gear Size 8.8" or 9.75" 8.8" or 9.75" 8.8" or 9.75" 8.8", 9.75" or 10.25" 8.8" or 9.75" 8.8" or 9.75" 7.5"

LUBRICATION CAPACITY LUBRICANT CAPACITY (1) Application Pts. (L) Expedition 5.5 (2.6) Explorer 5.5 (2.6) Mountaineer 5.5 (2.6) Navigator 5.5 (2.6) Ranger 5.0 (2.4) E Series 5.5 (2.6) F Series 8.8" & 9.75" Ring Gear 5.5 (2.6) 10.25" Ring Gear 6.5 (3.0) (1) If refilling, add 4 ounces (.12L) of Ford Friction Modifier (C8AZ-19B546-A) in addition to normal lubricant. FLUID TYPE Use Motorcraft Synthetic Axle Lubricant (F1TZ-19580-B or WSP-M2C192-A equivalent) and Friction Modifier (C8AZ-19B546-A or EST-M2C118-A equivalent). DRAINING & REFILLING Helpmelearn November-17-07 10:47:22 AM

Page 2

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Traction-Lok - 7.5", 8.8", 9.75" & 10.25" Ring Gear

CAUTION: DO NOT clean internal components of differential case with solvent. Clean components with lint-free shop towel only. Drive vehicle until lubricant is warm. Remove rear cover to drain lubricant. Remove gasket. Clean all lubricant from gasket surfaces. Install NEW gasket. Apply continuous bead of silicone sealant to axle housing, ensuring bead is inside of bolt hole pattern. Install rear cover within 15 minutes of applying silicone. Tighten bolts to specification. See TORQUE SPECIFICATIONS . Fill axle housing with lubricant until level with bottom of fill hole.

TROUBLE SHOOTING NOTE:

See appropriate table in TROUBLE SHOOTING article in GENERAL INFORMATION.

NOTE:

A slight "lock-unlock" action and associated sound from the differential on tight turns after extended highway driving is considered normal.

ON-VEHICLE TESTING NOTE:

Torque required to rotate wheel may decrease when wheel is turning.

1. Raise one wheel off ground, leaving opposite wheel firmly on ground. Install Traction-Lok Torque Adapter (T59L-4204-A) on mounting studs of raised wheel. Shift transmission into Neutral. Attach traction-lok torque adapter to torque wrench. 2. Using torque wrench to rotate wheel, note torque required to keep wheel rotating through several revolutions. If break-away torque (torque required to start wheel rotating) is not at least 20 ft. lbs. (27 N.m), and wheel does not turn smoothly without slipping, adjust clutch pack preload. See CLUTCH PACKS under OVERHAUL.

REMOVAL & INSTALLATION NOTE:

Because Traction-Lok and conventional rear axle assemblies are identical except for differential case, removal and installation procedures for both differential cases are the same. For removal and installation of components and differential case from axle housing, see appropriate differential article.

OVERHAUL NOTE:

This procedure is with differential case removed from axle housing. It is not necessary to remove differential bearings from differential case to overhaul differential case. Remove ring gear and speed sensor ring from carrier only if necessary. Vehicle speed sensor ring must be replaced if removed. It cannot be reused.

Helpmelearn November-17-07 10:47:22 AM

Page 3

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Traction-Lok - 7.5", 8.8", 9.75" & 10.25" Ring Gear

DISASSEMBLY NOTE:

Differential carrier bearings do not need to be removed from differential case during overhaul unless replacement is necessary.

7.5" & 8.8" Differential

WARNING: Preload spring is under pressure; remove carefully.

NOTE:

Thrust washers cannot be removed alone. They must be rotated out of case with pinion gears.

1. Remove ring gear. DO NOT remove ABS sensor ring (if equipped). If sensor ring is removed, it must be replaced. Remove pinion shaft lock bolt and pinion shaft. Grasp preload spring with pliers. Pull and tap preload spring until it is removed. 2. Remove both side gear and clutch pack assemblies, marking each assembly for installation reference. Disassemble side gear and clutch pack assemblies; note order of disassembly for reassembly reference. 9.75" & 10.25" Differential

NOTE:

Pinion gears are installed with preload. Thrust washers cannot be removed alone. Preload must be released and gears must be rotated out of case with thrust washers.

1. Remove ring gear. DO NOT remove ABS sensor ring (if equipped). If sensor ring is removed, it must be replaced. Remove pinion shaft lock bolt and pinion shaft. Install Traction-Lok Torque Tool (T97T-4205A) upright in a vise. Position differential case on tool. Install a lubricated Step Plate Adapter (D80L-6305) or equivalent into bottom gear spline. 2. Install Mandrel (T97T-4946-A) in upper facing side gear with nut positioned against mandrel. Tighten hex-head forcing screw until contact is made with step plate adapter. Use a bar to hold the nut and tighten forcing screw until preload pressure is released. See Fig. 2 . 3. Insert pinion gear rotating tool into pinion shaft bore and turn differential case to rotate gears and thrust washers into carrier windows. Remove pinion gears ans thrust washers. Remove differential side gears and clutch packs. Mark gears and clutch packs LEFT and RIGHT for reassembly reference.

Helpmelearn November-17-07 10:47:22 AM

Page 4

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Traction-Lok - 7.5", 8.8", 9.75" & 10.25" Ring Gear

Fig. 2: Using Mandrel & Forcing Screw To Relieve Side Gear Preload (9.75" & 10.25" Differentials) Courtesy of FORD MOTOR CO. INSPECTION CAUTION: DO NOT clean clutch plate friction surfaces with solvent. Wipe with clean shop towel only. DO NOT interchange clutches or shims. Inspect parts for Helpmelearn November-17-07 10:47:22 AM

Page 5

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Traction-Lok - 7.5", 8.8", 9.75" & 10.25" Ring Gear

uneven or extreme wear. Replace if necessary. CLUTCH PACK ADJUSTMENT Adjusting Clutch Pack Clearance

1. Disassemble clutch packs, noting order of disassembly for reassembly reference. DO NOT clean clutch plate friction surfaces with solvent. Wipe with clean shop towel only. Inspect clutch plates. Replace plates if they are uneven or extremely worn. 2. Install Differential Clutch Gauge Base (T84P-4946-A for 7.5" ring gear; T97P-4946-A for 8.8" and 9.75" ring gears) in vise. With side gear facing down, slide assembly onto base without shim. Install Differential Clutch Gauge Disc (part of T84P-4946-A for 7.5" ring gear; T80P-4946-A for 8.8", 9.75" and 10.25" ring gears) on top of assembly without shim. See Fig. 4 . 3. Install nut on threaded end of gauge base. Tighten nut to 60 INCH lbs. (6.7 N.m). Using feeler gauge, select thickest blade that will enter between clutch gauge and clutch pack. This reading will be thickness of new shim for that clutch pack. Shims are available in .005" (.13 mm) increments. See CLUTCH PACK SHIM SIZES table. Repeat procedure for opposite clutch pack. 4. Disassemble gauge and clutch packs. Lubricate clutch pack friction plates with Friction Modifier (C8AZ19B546-A or EST-M2C118-A). Reassemble side gear and clutch pack with appropriate size shim. DO NOT mix plates from side to side. NOTE:

A Differential Clutch Pack Rebuild Kit (F5ZZ4947-B) is available for the 7.5" differential.

CLUTCH PACK SHIM SIZES Part Number 10.25" Diameter Ring Gear F7TW-4A324-CA F7TW-4A324-DA F7TW-4A324-EA F7TW-4A324-FA F7TW-4A324-GA F7TW-4A324-HA F7TW-4A324-JA F7TW-4A324-KA 9.75" Diameter Ring Gear F7TW-4A324-AA F7TW-4A324-BA F7TW-4A324-CA F75Z-4A324-DA F75Z-4A324-EA F75Z-4A324-FA F75Z-4A324-GA

Shim Thickness - In. (mm) .025 (.64) .030 (.76) .035 (.89) .040 (1.02) .045 (1.14) .050 (1.27) .055 (1.39) .060 (1.52) .015 (.38) .020 (.51) .025 (.64) .030 (.76) .035 (.89) .040 (1.02) .045 (1.14)

Helpmelearn November-17-07 10:47:22 AM

Page 6

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Traction-Lok - 7.5", 8.8", 9.75" & 10.25" Ring Gear

F75Z-4A324-HA F75Z-4A324-JA F75Z-4A324-KA 8.8" Diameter Ring Gear EOAZ-4A324-G EOAZ-4A324-H EOAZ-4A324-C EOAZ-4A324-D EOAZ-4A324-F 7.5" Diameter Ring Gear E4DZ-4A324-G E4DZ-4A324-H E4DZ-4A324-C E4DZ-4A324-D E4DZ-4A324-F

.050 (1.27) .055 (1.40) .060 (1.52) .025 (.64) .030 (.76) .035 (.89) .040 (1.02) .045 (1.14) .025 (.64) .030 (.76) .035 (.89) .040 (1.02) .045 (1.14)

Fig. 3: Removing Clutch Pack Preload Spring Courtesy of FORD MOTOR CO. Helpmelearn November-17-07 10:47:22 AM

Page 7

© 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Traction-Lok - 7.5", 8.8", 9.75" & 10.25" Ring Gear

Fig. 4: Measuring Clutch Pack To Determine Shim Size Courtesy of FORD MOTOR CO. REASSEMBLY 7.5" & 8.8" Differential

1. Install side gears and thrust washers into differential case. Place pinion gears and thrust washers 180 degrees apart on side gears and rotate into case. 2. Use soft-faced hammer and drive "S"-shaped preload spring into position. Ensure spring is not damaged. Install pinion shaft and NEW pinion shaft lock bolt (use Threadlock (EOAZ-19554-AA) on lock bolt if new bolt is unavailable). Install bolt finger-tight at this time. 3. Place Traction-Lok Torque Tool (205-022/T66L-4204-A) in a vise. Position carrier on Torque Tool and measure rotating torque. Rotating torque should be 20 ft. lbs. (27 N.m). See Fig. 5 . 4. This checks torque required to rotate one side gear while other is held stationary. If clutch plates are used, break-away torque should be at least 20 ft. lbs. (27 N.m) and rotation should be smooth. If clutch plates are new, break-away torque may vary and be slightly higher than specification. 5. If break-away torque is as specified and rotation is smooth, tighten pinion shaft lock bolt to proper specification. See TORQUE SPECIFICATIONS . If sensor ring has been removed, align notch on new Helpmelearn November-17-07 10:47:22 AM

Page 8

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Traction-Lok - 7.5", 8.8", 9.75" & 10.25" Ring Gear

sensor ring with notch on case flange and install new ring. Install side bearings and ring gear, if necessary.

Fig. 5: Bench-Testing Traction-Lok Differential Courtesy of FORD MOTOR CO. 9.75" & 10.25" Differential

1. Install Traction Lock Torque Tool (T97T-4205-A) in a vise. Install side gears with differential clutch Helpmelearn November-17-07 10:47:22 AM

Page 9

Š 2005 Mitchell Repair Information Company, LLC.


1999 Ford Explorer 1998-99 DRIVE AXLES Differentials - Traction-Lok - 7.5", 8.8", 9.75" & 10.25" Ring Gear

packs, shims and Belleville spring washers into differential case. Position carrier on Torque Tool. Hold upper side gear in place to keep it from falling out. Apply grease to Step Bore Plate and assemble Mandrel and forcing screw in between side gears. See Fig. 2 . 2. Lubricate both sides of pinion gear thrust washers with Motorcraft Synthetic Axle Lubricant (F1TZ19580-B) or equivalent. Place differential pinion gears and thrust washers in carrier windows, 180 degrees apart, on side gears. Install pinion gear rotator handle into pinion gear hole of differential case. Rotate case until pinion gears are aligned with pinion shaft hole. Remove rotator handle from differential case. WARNING: Keep fingers and hands clear of pinion gears while rotating differential case. 3. Remove forcing screw, Mandrel and Step Bore Plate from differential case. Install pinion shaft and pinion shaft lock bolt. DO NOT tighten pinion shaft lock bolt at this time. Before installing differential case in axle housing, bench-test differential case clutch packs using Traction-Lok Torque Adapter (T59L-4204A). With differential carrier positioned on Torque Tool in vise, install second Torque Tool in upper side gear. See Fig. 5 . 4. Measure torque required to turn side gear. This checks torque required to rotate one side gear while other is held stationary. If clutch plates are used, break-away torque should be at least 20 ft. lbs. (27 N.m) and rotation should be smooth. If clutch plates are new, break-away torque may vary and be slightly higher than specification. If break-away torque (torque required to rotate side gear) is not at least 20 ft. lbs. (27 N.m) or rotation is not smooth, different shim must be installed in clutch pack. 5. If break-away torque is as specified and rotation is smooth, tighten pinion shaft lock bolt to proper specification. See TORQUE SPECIFICATIONS .

TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Filler Plug Differential Bearing Cap Bolt Pinion Shaft Lock Bolt Rear Cover Bolt Ring Gear Bolt 7.5" & 8.8" Differential 9.75" Differential

Ft. Lbs. (N.m) 22 (30) 77 (105) 22 (30) 33 (45) 77 (105) 100-120 (136-163)

Helpmelearn November-17-07 10:47:22 AM

Page 10

Š 2005 Mitchell Repair Information Company, LLC.


Thank you very much for your reading. Please Click Here Then Get More Information.


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.