Service Manual Chassis & Mast GC35K
AT87-00001-up AT87A-00001-up
GC55K
AT88-00001-up AT88A-00001-up
GC40K
AT87-00001-up AT87A-00001-up
GC55K STR
AT88-00001-up AT88A-00001-up
GC40K STR
AT87-00001-up AT87A-00001-up
GC60K
AT89-00001-up AT89A-00001-up
GC45K SWB
AT87-00001-up AT87A-00001-up
GC70K
AT89-00001-up AT89A-00001-up
GC45K
AT88-00001-up AT88A-00001-up
GC70K STR
AT89-00001-up AT89A-00001-up
For use with GM4.3L, G6 Engine Service Manual and Fuel System Supplement
99739-80120
FOREWORD This service manual is a guide to servicing of Cat Lift Trucks for 3.5 thru 7.0 ton models. The instructions are grouped by systems to serve the convenience of your ready reference. Long productive life of your lift trucks depends to a great extent on correct servicing — the servicing consistent with what you will learn from this service manual. We hope you read the respective sections of this manual carefully and know all the components you will work on before attempting to start a test, repair or rebuild job. The descriptions, illustrations and specifications contained in this manual were of the trucks of serial numbers in effect at the time it was approved for printing. Cat Lift Trucks reserves the right to change specifications or design without notice and without incurring obligation. The GM4.3L engine's fuel system was changed to comply with the EPA guidelines. This manual has minimal information on the fuel systems. Please see the Fuel System Supplement for information regarding the Multi Port Fuel Injection System (MPFI). For the items pertaining to the engines, refer to the following service manuals: • GM4.3L (G6) Engine Service Manual • GM4.3L Fuel System Supplement
SAFETY RELATED SIGNS The following safety related signs are used in this service manual to emphasize important and critical instructions: WARNING
Indicates a specific potential hazard resulting in serious bodily injury or death.
CAUTION
Indicates a specific potential hazard resulting in bodily injury, or damage to, or destruction of the machine.
NOTE
Indicates a condition that can cause damage to, or shorten service life of the machine.
Pub. No. 99739-80120
WARNING
SAFETY WARNING
WARNING
The proper and safe lubrication and maintenance for this lift truck, recommended by Mitsubishi, are outlined in the OPERATION & MAINTENANCE MANUAL for these trucks. Improper performance of lubrication or maintenance procedures is dangerous and could result in injury or death. Read and understand the OPERATION & MAINTENANCE MANUAL before performing any lubrication or maintenance.
Do not operate this truck unless you have read and understand the instructions in the OPERATION & MAINTENANCE MANUAL. Improper truck operation is dangerous and could result in injury or death. 4.
Lower the forks or other implements to the ground before performing any work on the truck. If this cannot be done, make sure the forks or other implements are blocked correctly to prevent them from dropping unexpectedly.
5.
Use steps and grab handles (if applicable) when mounting or dismounting a truck. Clean any mud or debris from steps, walkways or work platforms before using. Always face truck when using steps, ladders and walkways. When it is not possible to use the designed access system, provide ladders, scaffolds, or work platforms to perform safe repair operations.
6.
To avoid back injury, use a hoist when lifting components which weighs 23 kg (50 lb.) or more. Make sure all chains, hooks, slings, etc., are in good condition and are of the correct capacity. Be sure hooks are positioned correctly. Lifting eyes are not to be side loaded during a lifting operation.
7.
To avoid burns, be alert for hot parts on trucks which have just been stopped and hot fluids in lines, tubes and compartments.
8.
Be careful when removing cover plates. Gradually back off the last two bolts or nuts located at opposite ends of the cover or device and pry cover loose to relieve any spring or other pressure, before removing the last two bolts or nuts completely.
9.
Be careful when removing filler caps, breathers and plugs on the truck. Hold a rag over the cap or plug to prevent being sprayed or splashed by liquid under pressure. The danger is even greater if the truck has just been stopped because fluids can be hot.
The serviceman or mechanic may be unfamiliar with many of the systems on this truck. This makes it important to use caution when performing service work. A knowledge of the system and/or components is important before the removal or disassembly of any component. Because of the size of some of the truck components, the serviceman or mechanic should check the weights noted in this Manual. Use proper lifting procedures when removing any components. Following is a list of basic precautions that should always be observed. 1.
Read and understand all warning plates and decals on the truck before operating, lubricating or repairing the product.
2.
Always wear productive glasses and protective shoes when working around trucks. In particular, wear protective glasses when pounding on any part of the truck or its attachments with a hammer or sledge. Use welders gloves, hood/goggles, apron and other protective clothing appropriate to the welding job being performed. Do not wear loose-fitting or torn clothing. Remove all rings from fingers when working on machinery.
3.
Do not work on any truck that is supported only by lift jacks or a hoist. Always use blocks or jack stands to support the truck before performing any disassembly.
10. Always use tools that are in good condition and be sure you understand how to use them before performing any service work. 11. Reinstall all fasteners with same part number. Do not use lesser quality fastener if replacements are necessary. Do not mix metric fastener with standard nuts and bolts. 12. If possible, make all repairs with the truck parked on a level, hard surface. Block truck so it does not roll while working on or under truck. 13. Disconnect battery and discharge any capacitors (electric trucks) before starting to work on truck. Hang “Do not Operate� tag in the Operator’s Compartment. 14. Repairs, which require welding, should be performed only with the benefit of the appropriate reference information and by personnel adequately trained and knowledgeable in welding procedures. Determine type of metal being welded and select correct welding procedure and electrodes, rods or wire to provide a weld metal strength equivalent at least to that of parent metal. 15. Do not damage wiring during removal operation. Reinstall the wiring so it is not damaged nor it will be damaged in operation by contacting sharp corners, or by rubbing against some object or hot surface. Do not connect wiring to a line containing fluid. 16. Be sure all protective devices including guards and shields are properly installed and functioning correctly before starting a repair. If a guard or shield must be removed to perform the repair work, use extra caution. 17. Always support the mast and carriage to keep carriage or attachments raised when maintenance or repair work is performed, which requires the mast in the raised position.
18. Loose or damaged fuel, lubricant and hydraulic lines, tubes and hoses can cause fires. Do not bend or strike high pressure lines or install ones which have been bent or damaged. Inspect lines, tubes and hoses carefully. Do not check for leaks with your hands. Pin hole (very small) leaks can result in a high velocity oil stream that will be invisible close to the hose. This oil can penetrate the skin and cause personal injury. Use cardboard or paper to locate pin hole leaks. 19. Tighten connections to the correct torque. Make sure that all heat shields, clamps and guards are installed correctly to avoid excessive heat, vibrations or rubbing against other parts during operation. Shields that protect against oil spray onto hot exhaust components in event of a line, tube or seal failure, must be installed correctly. 20. Relieve all pressure in air, oil or water systems before any lines, fittings or related items are disconnected or removed. Always make sure all raised components are blocked correctly and be alert for possible pressure when disconnecting any device from a system that utilizes pressure. 21. Do not operate a truck if any rotating part is damaged or contacts any other part during operation. Any high speed rotating component that has been damaged or altered should be checked for balance before reusing.
HOW TO READ THIS MANUAL Disassembly diagram (example)
2
1 4
Each disassembly diagram is followed by Disassembly sequence and Suggestions disassembly.
3
▲
1 Cover, Bolt, Washer (part name) 2 Output shaft (part name)
▲
Disassembly sequence
▲
Suggestion for disassembly (1) Output shaft removal Unit: mm (in.) Clearance between cylinder and piston
A
0.020 to 0.105 (0.00079 to 0.00413)
B
0.15 (0.0059)
A: Assembly standard B: Repair or service limit
Symbols or abbreviations OP..........................Option R1/4 ......................Taper pipe thread (external) 1/4 inch (formerly PT1/4) Rc1/8 ....................Taper pipe thread (internal) 1/8 inch (formerly PT1/8) G1/4A ....................Straight pipe thread (external) 1/4 inch (formerly PF1/4-A) Rp1/8 ....................Straight pipe thread (internal) 1/8 inch (formerly PS1/8)
GENERAL INFORMATION
Vehicle Exterior • This Service Manual deals with all components or systems of the Cat Lift Trucks; except for the engine and attachment, which are covered in the respective manuals.
102530A
Models This manual applies to the following vehicle models (names). Truck Models
Transmission
Serial number
Engine mounted
GC35K GC40K AT87-00001-up AT87A-00001-up
GC40K STR GC45K SWB
1-Speed
GC45K
GM4.3L Gasoline Engine
GC55K
AT88-00001-up AT88A-00001-up
GC55K STR GC60K GC70K GC70K STR
Automatic 2-Speed
AT89-00001-up AT89A-00001-up
1-1
GENERAL INFORMATION
Serial Number Locations
Name Plate
Chassis Serial Number
Mast Number
Transmission Serial Number
Gasoline Engine Serial Number
207831
1-2
GENERAL INFORMATION
Chassis and Mast Model Identification [Chassis] GC 55 K
Generation designator
Maximum capacity 55 :5500kg (12000lb) Engine type GC: gasoline engine type
[Mast] A
55 A
33
Maximum lifting height (“33” stands for 3300mm.) Order of the minor change (“A” for the original, “B” for the first change, “C” for the second change, and so on) Applicable truck model designation 55:5.5 ton class
Kind of mast A: simplex mast B: duplex mast C: triplex mast
1-3
GENERAL INFORMATION
Dimensions
F
K
J
I
D A
G
H B
N C
L E
1-5
M 206999
GENERAL INFORMATION
Technical Data Ref. No. A
B
Unit: mm (in.) Truck Models GC35K
Items Maximum lift Simplex mast Free lift (Floor to forktop)
GC40K
GC40K STR
3050 (120)
2900 (114)
Simplex mast
150 (5.9)
160 (6.3)
Duplex mast
920 (36.2) 3.0 m (118 in.) mast
895 (35.2) 2.8 m (112 in.) mast
Triplex mast
800 (31.5) 4.0 m (157 in.) mast
920 (36.2) 4.3 m (169 in.) mast
C
Fork length
D
Tilt angle (forward – backward)
E
Overall length (OLH)
F
Overall width Standard (outside) Wide tread (option)
G
Overall height (to top of mast lowered)
2155 (85.0)
H
Overall height (to top of overhead guard)
2155 (85.0)
1220 (48) 5/10 Simplex, Duplex mast 6/5 Triplex mast
deg. 2510 (98.5)
2550 (100)
2360 (93)
2620 (103)
1180 (46.5) 1270 (50.0)
4250 (167)
4125 (162)
Overall height (mast extended) Duplex mast
4250 (167) 3.0 m (118 in.) mast
4080 (160.6) 2.8 m (112 in.) mast
Triplex mast
5250 (206.7) 4.0 m (157 in.) mast
5560 (218.9) 4.3 m (169 in.) mast
Simplex mast I
GC45K SWB
Standard
940 (37.0)
Wide tread (option)
1040 (41.0)
J
Tread (front)
K
Tread (rear)
980 (38.5)
L
Wheelbase
1575 (62.0)
M
Rear overhang
N
Underclearance (at frame)
485 (18.8)
525 (20.3)
335 (13.3)
150 (5.9)
1-6
565 (22.1)
GENERAL INFORMATION
Unit: mm (in.) GC45K
GC55K STR
GC55K
GC60K
GC70K
2900 (114)
2350 (93)
160 (6.3)
165 (6.5)
GC70K STR
895 (35.2) 2.8 m (112 in.) mast 895 (35.2) 4.0 m (157 in.) mast
900 (35.4) 3.5 m (138 in.) mast 1220 (48)
5/10 Simplex, Duplex mast 6/5 Triplex mast 2730 (107)
2910 (115)
6/10 Simplex mast 6/5 Triplex mast
2640 (104)
2950 (116)
1320 (52.0)
2730 (107)
1440 (56.5)
1420 (56.0) 2155 (85.0)
2205 (87.0)
2155 (85.0)
2205 (87.0)
4125 (162)
3585 (141)
4080 (160.6) 2.8 m (112 in.) mast 5560 (218.9) 4.0 m (157 in.) mast
4785 (188.3) 3.5 m (138 in.) mast
1015 (40.0)
1130 (44.5)
1120 (44)
470 (18.1)
965 (38.0)
1160 (45.5)
1780 (70.0)
1830 (72.0)
650 (26.1)
380 (15.1)
590 (23.1)
150 (5.9)
200 (7.9)
1-7
340 (13.1)
GENERAL INFORMATION
Technical Data GC35K
GC40K STR
GC40K
Traveling performance
Work performance
Truck Models Capacity/load center
kg/mm (lb/in.)
Maximum lift height Simplex
mm (in.)
3050 (120)
2900 (114)
Lift speed (loaded)
540 (105)
390 (78.0)
Lowering speed (loaded)
mm/sec. (fpm)
550 (108)
440 (86.5)
Mast tilt (forward-backward)
degree
Free lift
mm (in.)
Gradeability at 1 mph (1.6 km/h)
mm (in.)
Loaded No loaded
%
Loaded No loaded
Overall length to fork face Overall width
Overall height
2340 (92.0)
2245 (88.5)
2295 (90.5)
2100 (82.5)
2350 (92.5)
37
33
32
27
23.8
21.1
21.5
17.7
42
37
36
30
23.8
21.1
21.5
17.7
2510 (98.5)
2550 (100)
2360 (93)
2620 (103)
1180 (46.5)
Wide tread (optional)
1270 (50.0)
To top of mast (lowered)
2200 (86.5)
2350 (92.5)
To top of mast (extended)
4250 (167.5)
4130 (162.5)
2155 (85.0)
mm (in.)
1575 (62.0) Standard
940 (37.0)
Wide tread (optional)
1040 (41.0) 980 (38.5)
Rear
485 (18.8)
Single Front wheels
Service weight Single wheels -no load (without load) Axle Front loading Rear
525 (20.3)
335 (13.3)
565 (22.1)
150 (5.9) 22×9×16
mm
Rear Weight
18.5 (11.5)
2090 (82.5)
Underclearance (at frame) Tire size
19 (12.0)
2285 (90)
Rear Overhang
160 (6.5)
2235 (88.0)
Wheelbase
Tread
150 (6.0)
Standard
To top of overhead guard
Front
4500/600 (10000/24)
19.5 (12.5)
Minimum turning radius Minimum intersecting isle Standard
4000/500 (8000/24)
5/10
Loaded Travel Powershift km/h transmission speed (mph) No load models
Gradeability at stall
Dimensions
3500/500 (7000/24)
GC45K SWB
18×7×12.12
kg (lb)
5200 (11500)
5600 (12300)
5700 (12700)
6500 (14300)
2050 (4600)
2025 (4400)
2150 (4900)
1925 (4200)
3150 (6900)
3575 (7900)
3550 (7800)
4575 (10100)
1-8
GENERAL INFORMATION
GC45K
GC55K STR
GC55K
4500/600 (10000/24)
GC60K
5500/600 (12000/24)
GC70K STR
GC70K
6000/600 (13500/24)
7000/600 (15500/24)
2900 (114)
2360 (93)
390 (78.0)
360 (71.0)
440 (86.5)
540 (106.0)
5/10
6/10
160 (6.5)
165 (6.5)
18.5 (11.5)
18 (11.5)
21 (13.0)
19.5 (12.5)
20.5 (12.5) 23 (14.5)
22.5 (14.0)
2440 (96.0)
2550 (100)
2350 (92.5)
2570 (101.0)
2400 (94.5)
2345 (92.5)
2455 (96.5)
2255 (89)
2395 (94.5)
2220 (87.5)
26
22.6
22.2
24.5
21.7
21.4
23.8
20.2
20.9
22.2
19.7
20.4
30
26
25
30
27
26
23.8
20.2
20.9
22.2
19.7
20.4
2730 (107)
2910 (115)
2460 (104)
2950 (116)
1320 (52.0)
2700 (106)
1440 (56.5)
1420 (56.0) 2350 (92.5)
2530 (99.5)
4130 (162.5)
2370 (93.0)
2155 (85.0)
2205 (87.0)
1780 (70.0)
1830 (72.0)
1015 (40.0)
1135 (44.5)
1115 (44.0) 965 (38.0) 470 (18.1)
18×8×12.12
650 (26.1)
1160 (45.5) 380 (15.1)
590 (23.1)
150 (5.9)
200 (7.9)
22×12×16
28×12×12
18×8×12.12
340 (13.1)
22×8×16
6600 (14500)
7200 (15800)
7400 (16200)
8800 (19300)
9500 (20900)
9700 (21300)
2625 (5700)
2425 (5300)
2625 (5700)
3300 (7300)
3300 (7200)
3500 (7500)
3975 (8800)
4775 (10500)
4775 (10500)
5500 (12000)
6200 (13700)
6200 (13800)
1-9
GENERAL INFORMATION
MPFI specs in Bold. If not indicated in bold, specs are for Carbureted and MPFI systems. Truck Models GC35K
GC40K STR
GC40K
Items Engine model
GM4.3L
Type
Gasoline
Cooling system
Water cooled
No. of cylinders-arrangement
6-90°V
No. of strokes
4
Type of combustion chamber
Semi-spherical
Valve arrangement
Overhead
Type of cylinder liners
Integral
Cylinder bore × stroke, mm (in.)
101.6×88.39 (4.00×3.48)
Engine
Displacement, cc (cu in.)
4293 (262)
Compression ratio
9.2 : 1
Rated output, PS/rpm
94/2450
Rated torque, kgf·m/rpm
31.0/1200
Min. rpm
750-800, 650-700
Max. rpm
2650-2700, 2600-2650
Dimensions (L×W×H), mm (in.)
710×620×740 (28.0×24.4×29.1)
Weight, kg (lb)
260 (573)
Installation position
Rear
Ignition
Spark
Firing order
Ignition system
1-6-5-4-3-2
Initial ignition timing, BTDC deg
0° Gasoline, 8° L.P.G., ECU Controlled
Fuel tank capacity, liter (U.S.gal)
66 (17.4)
Ignition coil
Fuel system
GC45K SWB
Distributor
Type
Mold
Type
Pointless
Type of spark advance control
Internal solid state circuit, ECU Controlled
Model Spark plug
AC #41-932, R42LTS
Size, mm (in.)
14 (0.55)
Gap, mm (in.)
1.24 (0.0488), .89 (.035)
Carburetor
Type
Single Barrel, MPFI
Governor
Type
Electronic
Fuel pump
Type
Electromagnetic
Air cleaner
Type × Number
Cyclone with paper element × 1
1-10
GENERAL INFORMATION
MPFI specs in Bold. If not indicated in bold, specs are for Carbureted and MPFI systems. GC45K
GC55K
GC55K STR
GC60K
GC70K
GM4.3L Gasoline Water cooled 6-90°V 4 Semi-spherical Overhead Integral 101.6×88.39 (4.00×3.48) 4293 (262) 9.2 : 1 92.6/2450 31.0/1200 750-800, 650-700 2650-2700, 2600-2650 710×620×740 (28.0×24.4×29.1) 260 (573) Rear Spark 1-6-5-4-3-2 0° Gasoline, 8° L.P.G., ECU Controlled 80 (21.1)
128 (34.0) Mold Pointless Internal solid state circuit AC #41-932, R42LTS 14 (0.55) 1.24 (0.0488), .89 (.035) Single Barrel, MPFI Electronic Electromagnetic Cyclone with paper element × 1
1-11
GC70K STR
GENERAL INFORMATION
MPFI specs in Bold. If not indicated in bold, specs are for Carbureted and MPFI systems. Truck Models GC35K
GC40K STR
GC40K
Engine lublication system
Type
Starter
Alternator
Battery
Type
Cooling system
Items
Pressure feed
Oil pump
Gear pump
Oil filter
Paper element
Oil cooler
Oil to water type
Refill capacities, liter (U.S.gal)
GC45K SWB
Oil pan
4.2 (1.1)
Oil filter & cooler
0.8 (0.2)
Total
5.0 (1.3) Forced circulation
Radiator
Plate fins with pressure cap
Refill capacity, liter (U.S.gal) Water pump
11 (2.9) Centrifugal type, V-belt driven, Serpentine belt driven
Thermostat/ Opening Temp F°
Wax type/ 180
Type Ă— number
Group 24
Voltage, V
12
Capacity, AH (5Hr)
45
Type
3-Phase AC
Manufacturer
MANDO, AC Delco
Rated output, V-A
12-50, 12-70
Regulator
Built in IC type
Type
Electromagnetic
Manufacturer
Delco Remy
Voltage-output, V-kW
12 - 0.75
1-12
GENERAL INFORMATION
MPFI specs in Bold. If not indicated in bold, specs are for Carbureted and MPFI systems. GC45K
GC55K
GC55K STR
GC60K
GC70K
Pressure feed Gear pump Paper element Oil to water type 4.2 (1.1) 0.8 (0.2) 5.0 (1.3) Forced circulation Plate fins with pressure cap 11 (2.9) Centrifugal type, V-belt driven, Serpentine belt driven Wax type/ 180 Group 24 12 45 3-Phase AC MANDO, AC Delco 12-50, 12-70 Built in IC type Electromagnetic Delco Remy 12 - 0.75
1-13
GC70K STR
GENERAL INFORMATION
Truck Models GC35K
GC40K STR
GC40K
Items Type Torque converter
3-element, 1-stage, 2-phase
Manufacturer’s model
Okamura M15
Stall torque ratio
3.2
Control and shift
Power train
Transmission Powershift Reduction gear
Ratios
Hydraulic and column shift
Forward
2.898
Reverse
2.907
Type of gear
Spiral bevel
Gear ratio
4.571
Housing
Banjo
Differential Type of gear and pinion number
Gear
Straight bevel-2
Pinion
Straight bevel-4
Transmission/ torque converter oil liter (U.S. gal)
14 (3.7)
Differential gear oil liter (U.S. gal)
9.1 (2.4)
Steering system
Type
Full Hydrostatic power stearing
Steering wheel diameter, mm (in.)
330 (13)
Power cylinder ID × rod diam., mm (in.) Power steering
85×60 (3.3×2.4)
Effective stroke, mm (in.)
155 (6.1)
Relief pressure, kPa (kgf/cm2) [psi]
11768 (120) [1706]
Traveling system
Flow rate, liter (U.S.gal)/min
23 (6.07)
Front axle
Full-floating tubular type
Rear axle
Elliott type
Suspension system
Front
Fixed type
Rear
Center-pivot type
Toe-in, mm (in.) Wheel alignment
0
Camber
1.0°
Caster
0°
Kingpin inclination
0°
1-14
GC45K SWB
GENERAL INFORMATION
GC45K
GC55K
GC55K STR
GC60K
GC70K
3-element, 1-stage, 2-phase Okamura M15 3.2 Hydraulic and column shift 2.898
(1st/2nd) 5.104/2.882
2.907
(1st/2nd) 5.104/2.882
Spiral bevel
Hypoid gear
4.571
4.857 Banjo Straight bevel-2 Straight bevel-4 Transmission/ Torque oil 15 (3.9) 9.1 (2.4) Full Hydrostatic power stearing 328 (12.9) 85×60 (3.3×2.4)
155 (6.1)
180 (7.1)
11768 (120) [1706]
14710 (150) [2133] 23 (6.07) Full-floating tubular type Elliott type Fixed tpe Center-pivot type 0 1.0° 0° 0°
1-15
GC70K STR
GENERAL INFORMATION
Truck Models GC35K
GC40K STR
GC40K
Items
Btake system
Type Service brakes
Parking brake
Self-adjusting, duo-servo
Drum diameter, mm (in.)
317.5 (12.50)
Lining (length×width thick×number), mm (in.)
330×63×10-2 (13×2.48×0.39-2)
Master cylinder ID, mm (in.)
28.57 (1.125)
Wheel cylinder ID, mm (in.)
31.75 (1.250)
Type
Mechanical, mounted on wheels
Brake fluid cc (cu.in)
130 (7.9)
Brake booster
Mastervac (vacuum suspended)
Body
Assembled-frame type Type
Gear
Manufacturer’s type Gear pump
Control valve Hydraulic system
GC45K SWB
Flow regulator valve
KFP3240 AMBAS
Rated discharge, liter (U.S.gal)/rpm
98 (25.89)/2450
Drive line
Universal joint
Type
6000-C193
Relief pressure, MPa (kgf/cm2) [psi]
19.12
Type
+0.5 0
(195
+5 0
) [2773
+71 0 ]
Variable (Adjustable)
Regulated flow rate, liter (U.S.gal)/min
100 (26.4)
115 (30.38)
Simplex mast ID, mm (in.) Lift cylinders Stroke, mm (in.)
60 (2.36)
70 (2.75)
Duplex mast ID, mm (in.) First lift cylinders Stroke, mm (in.)
90 (3.54)
110 (4.33)
820 (32.28)
845 (33.27)
55 (2.17)
60 (2.36)
1590 (62.60)
1585 (62.40)
90 (3.54)
110 (4.33)
820 (32.28)
845 (33.27)
60 (2.36)
70 (2.75)
1480 (58.27)
1530 (60.24)
1650 (65)
Duplex mast ID, mm (in.) Second lift cylinders Stroke, mm (in.) Triplex mast ID, mm (in.) First lift cylinders Stroke, mm (in.) Triplex mast ID, mm (in.) Second lift cylinders Stroke, mm (in.) Tilt cylinders
ID, mm (in.)
100 (3.937)
Stroke, mm (in.)
120 (4.724)
Hydraulic tank capacity, liter (U.S.gal)
46 (12.1)
1-16
GENERAL INFORMATION
GC45K
GC55K
GC55K STR
GC60K
GC70K
Self-adjusting, duo-servo 317.5 (12.50) 330×63×10-2 (13×2.48×0.39-2) 28.57 (1.125) 31.75 (1.250) Mechanical, mounted on wheels 130 (7.9) Mastervac (vacuum suspended) Assemled-frame type Gear KFP3240 AMBAS
SPG2-48L194
98 (25.89)/2450
117.6 (31.07)/2450 Universal joint 6000-C193 19.12
+0.5 0
(195
+5 0
) [2773
+71 0 ]
Variable (Adjustable) 115 (30.38)
165 (43.56)
70 (2.75)
80 (3.15) 1650 (65)
110 (4.33) 845 (33.27) 60 (2.36) 1585 (62.40) 110 (4.33)
125 (4.92)
845 (33.27)
855 (33.66)
70 (2.75)
80 (3.15)
1530 (60.24)
1495 (58.86)
100 (3.937)
110 (4.33)
120 (4.724)
139 (5.472)
52 (13.6)
69 (18.2)
1-17
GC70K STR
GENERAL INFORMATION
Truck Models GC35K
GC40K
Items
Mast and forks
Mast model
GC40K STR
GC45K SWB
CJ type
Flange ID × flange Outer back thickness × flange front thickness × Inner, Middle web thickness Main rollers
Bearing
Side rollers
Bearing
118×28×24×13 (4.6×1.1×0.9×0.5)
130×30×26×15 (5.1×1.2×1.0×0.6)
118×24×24×12 (4.6×0.9×0.9×0.47)
130×26×26×13 (5.1×1.0×1.0×0.5)
Ball bearing
Diam × width, mm (in.)
118×32 (4.65×1.26)
130×34 (5.12×1.34)
Lubricated type needle roller bearing
Diam × width, mm (in.)
52×36 (2.05×1.42)
Lift chains
BL834
Fork (length × width × thick), mm (in.)
1220×150×50 (48×6×2)
Fork spread (outer width), mm (in.)
1060 (41.5)
1-18
BL1034
GENERAL INFORMATION
GC45K
GC55K STR
GC55K
GC60K
GC70K
GC70K STR
CJ type 130×30×26×15 (5.1×1.2×1.0×0.6)
150×34×30×20 (5.9×1.3×1.2×0.8)
130×26×26×13 (5.1×1.0×1.0×0.5)
150×30×30×15 (5.9×1.2×1.2×0.6) Ball bearing
130×34 (5.12×1.34)
150×36 (5.91×1.42)
Lubricated type needle roller bearing 52×36 (2.05×1.42)
58×40 (2.3×1.6) BL1034
1220×150×60 (48×6×2.4)
1220×150×65 (48×6×2.56)
1060 (41.5)
1230 (48.5)
1-19
COOLING SYSTEM
Description
6 •
5 •
8 •
9 •
4 1 •
• 7
•
•
3
2
207009
1 2 3 4
5 6 7 8 9
Engine Universal joint Gear pump Fan belt
2-1
Cooling fan Upper hose Lower hose Radiator Transmission Oil Cooler
COOLING SYSTEM
Removal and Installation Fan Belt Removal 1. Method by removing radiator
3
2 1
207010
Removal sequence 1 Universal joint 2 Tension pulley bolt (loosening only) 3 Belt Start by: Remove the radiator cover.
2-2
COOLING SYSTEM
Suggestions for removal and installation (1) Loosen the tension pulley bolt until the fan tension becomes loose. (2) Force the pulley all the way toward the fan and remove fan belt. Installation To install, follow the reverse of removal procedure and do the following steps: (1) Turn the fan by hand to make sure it rotates smoothly. If its bearing is noisy, replace it. (2) After putting the belt on the drive and driven pulleys, push it midway between the pulleys to make sure the tension pulley moves freely. Then, tighten the pulley bolt.
2-3
COOLING SYSTEM
Inspection and Adjustment Fan Belt Inspection (1) Check to make sure the belt is free of oil, grease or other foreign matter. Replace the belt if necessary. A slightly dirty belt can be re-used by cleaning with cloth or paper. Do not attempt to clean the belt with gasoline or the like. (2) At the time of overhauling the engine or adjusting the belt tension, closely check the belt and replace it if it is defective. Fan Belt Adjustment (1) Loosen the tension pully bolt by one to two full turns with ratchet wrench.
Tension pully bolt 207011
(2) The belt will be properly tightened by the tension spring. Tighten the tension pulley bolt.
2-4
ELECTRICAL SYSTEM
Description Console Box
4
1 Engine coolant temperature gauge 2 Speed selector switch (Only for 6 & 7 ton models) 3 Fuel gauge 4 Service hourmeter 5 OK monitor (Indicator Lights) 6 Starter switch 7 Light switch 8 Fuse box
5 3 1 7 6
2 8
102868
OK monitor 1
2
3
4
5
6
7
8
102869
Function No.
Indicator light
OFF
On or flickering
1
Powershift transmission oil temp. indicator light
Normal
Overheating
2
Air cleaner element indicator light
Normal
Clogged
3
Brake fluid level indicator light
Normal
Low
4
Engine oil pressure indicator light
Normal
Low
5
Alternator not charging indicator light
Normal
Abnormal
6
LPG residual pressure alarm lamp
Normal
Small
7
Malfunction indicator lamp
Normal
Service engine
8
Engine coolant level warning light
Normal
Low
Remarks
Option Option
How to check indicator light bulbs The bulbs are normal if the indicator lights come ON when the starter switch key is turned to â?™ (ON) position. (The indicator lights will go OFF when the engine starts.) 3-1
ELECTRICAL SYSTEM
Disassembly and Reassembly Console Box
2
4
⎧ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎨ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎩
3
1 207751
Disassembly 1. Disconnect the electrical wires at connectors 1. 2. Remove screws 2 (four) securing the cover. 3. Remove screws 3 (six) and separate the front and rear panels. 4. Remove screws 4 (four) securing the instrument panel. NOTE To replace the instrument panel bulbs, remove screws 3 and 4.
3-2
Reassembly To reassemble the console box, follow the reverse of disassembly procedure.
ELECTRICAL SYSTEM
Components in Console Box
4
3 2 1
5
6
207752
4 Light switch 5 Starter switch 6 Fuses
1 Power relay 2 Power relay 3 Turn signal relay
3-3
ELECTRICAL SYSTEM
Combination Meter Disassembly
1
2 3 4 5
6
7 8 9 206480
Sequence 1 Instrument panel 2 Dial 3 Engine coolant temperature gauge 4 Service hour meter 5 Fuel gauge
6 7 8 9
Meter case Printed circuit Bulb Socket
Bulb replacement
CAUTION Be careful not to damage the printed circuit when disassembling the combination meter.
For bulb replacement, remove the socket from the printed circuit by turning it counterclockwise. For configuration of the indicator lights, refer to “OK Monitor�.
Reassembly To reassemble the combination meter, follow the reverse of disassembly sequence. 3-4
ELECTRICAL SYSTEM
Major Electrical Components Starter Switch (with Anti-restart Lock) This switch has a built-in anti-restart lock, so the key cannot be turned from ❙ (ON) to (START) position while the engine is running.
(OFF) (ON)
B
(START)
203561A Connection Terminal
B
Component Fuse box, battery, Key alternator position ● (OFF) ❙ (ON) (START)
● ● ●
M Fuse box, fuel-cut solenoid
S Starter, neutral switch (powershift transmission)
● ●
●
3-5
ELECTRICAL SYSTEM
Lighting Switch
8 (0.3)
8 (0.3)
OFF 1st 2nd Knob position Stroke, mm (in.)
206481
Connection chart Terminal Component Knob position ● (OFF) 1st position 2nd position
B Battery (fuse)
T Tail lights, instrument light
H Working Head lights
Head lights
● ●
● ●
●
● ●
3-6
P
ELECTRICAL SYSTEM
Fuse Box
A B C D E F G H J
Code A
Amp 10 A
B C
15 A 15 A
D
15 A
E F G H J
15 A 10 A 10 A 15 A 10 A
Circuit Solenoid (F - R) Instrument panel light, turn signals, backup lights Spare terminal Tail lights, clearance lights, working lights (option) Head lights Spare fuse Horn Fuel pump relay Engine, ECU
101441D
Spare Terminals The spare terminal cord extends from the fuse box in the console box. (Another spare terminal is located on the chassis-side main harness.) Wire color: Lg (light green) Removing the console box rear panel will expose this spare terminal which is fastened to the harness protector with vinyl tape. Spare terminal
3-7
206424
Thank you very much for your reading. Please Click Here Then Get More Information.