Š 2012. It is prohibited to reproduce, even partially, texts and images in this leaflet without prior written consent of 4Technique. May 2014
1
www.upracks.com
w w w. u p r a c k s . c o m 2
MODELS
The standard version is powder-coated in black colour. Powder-coated natural aluminium version is also available.
UPRACKS roof racks have been designed to meet any roof load requirement. The sizes mentioned here below allow any type of application on all 4x4, SUV and Crossover vehicles. In fact, the sizes available, configured in different lengths and widths, can be readily combined to any vehicle roof. Just check the effective surface area of your vehicle roof, and select the correct size of our UPRACKS roof rack to be fitted. UPRACKS roof racks are made of 100% aluminium alloy, which results in reduced weight at the vehicle uppermost point: the roof. It is essential to remember that when you drive off-road (but not only off-road!) the materials, equipment, and accessories carried should be well arranged both inside and outside the vehicle. The high weight materials should be arranged with their load centre as low as possible, while roof load should be reduced to the maximum extent to avoid dangerous swaying movements. For example, an iron or steel roof rack is unfavourable due to its weight per se, which limits load capacity. Because UPRACKS roof racks have a very reduced weight they offer better load capacity. The maintenance manual provided by vehicle manufacturers usually provides specific information on the maximum load permitted and it is important to comply with such indications. UPRACKS has been able to build roof racks which are as low as 14-34 Kg in weight according to roof rack specific sizes. Following is an example: If a vehicle manufacturer specifies a 100 Kg maximum load capacity, the effective carrying capacity is the net weight derived by deducting the tare weight. Therefore, because an aluminium roof rack weighs only 25 Kg, you can carry 75 Kg materials on the roof; on the contrary an iron or steel roof rack weighs at least three times more, i.e. 75 Kg, and would allow only 25 kg load to be carried on the roof! UPRACKS roof racks can be fitted to the roof by special leg kits which are available for vehicles with and without gutter rails. In other words, we can offer all solutions for a proper fitting. Except for those vehicles having fixed attachment points on the roof (in which case we provide a proper customized kit), all the other vehicles can be equipped with our leg kits which are available in four different heights to be perfectly combined to all vehicle roofs. UPRACKS roof racks can be attached to the roof with solutions of 3-7 legs per each side; for this reason, leg kits are provided as a pair, thus offering the maximum freedom of choice. The profiles which make up the frame, lower support and usable platform area of UPRACKS roof racks have a special slot which allows attachment for any materials and accessories by a special “slide-in-all” system; a special M8 rectangular nut slides into this slot, thus enabling all the accessories to be securely bolted. UPRACKS roof racks, leg kits and accessories are all cataphoresis treated and then powder-coated in black colour; all nuts and bolts provided are fully made of stainless steel and galvanized iron. Upon request, we can provide a non-treated roof rack in polished natural aluminium.
PART NUMBERS, SIZES AND FINISHINGS 63-1109 1079×907 mm 63-1109P 1079×907 mm 63-1409 1432,5×907 mm 63-1409P 1432,5×907 mm 63-1410 1432,5×1097 mm 63-1410P 1432,5×1097 mm 63-1412 1432,5×1287 mm 63-1412P 1432,5×1287 mm
black aluminium polished aluminium black aluminium polished aluminium black aluminium polished aluminium black aluminium polished aluminium
63-1710 1786×1097 mm 63-1710P 1786×1097 mm 63-1712 1786×1287 mm 63-1712P 1786×1287 mm 63-1714 1786×1477 mm 63-1714P 1786×1477 mm 63-1914 1950×1477 mm 63-1914P 1950×1477 mm
black aluminium polished aluminium black aluminium polished aluminium black aluminium polished aluminium black aluminium polished aluminium
63-2112 2139,5×1287 mm 63-2112P 2139,5×1287 mm 63-2114 2139,5×1477 mm 63-2114P 2139,5×1477 mm 63-2414 2493×1477 mm 63-2414P 2493×1477 mm 63-2814 2846,5×1477 mm 63-2814P 2846,5×1477 mm
black aluminium polished aluminium black aluminium polished aluminium black aluminium polished aluminium black aluminium polished aluminium
PROFILES
w w w. u p r a c k s . c o m 3
TOP RAILS (TR) To get a complete superior top rail that conforms perfectly to the external roof rack frame, you can order a complete set that has everything that you need to fit it. This set is composed with front and rear frames, two sides frames, four bended frame corners and supports (63-ASRFITS2) with inserts and bolts to connect the top rail to the roof rack. Easy to order! For example if you need a complete Top Rail for a roof rack part number 63-1410 you just have to order 63-1410TR. Parts 63-ASRFITS2 are also sold separately in pairs if you need more supports. More! If you want to personalize your UPRACKS cage, you can also fit the top rail in two ways using this special support supplied! See the pictures! One way is bolt it on top and have a 45mm clearance between the roof rack and top rail (solution 1). The other way is bolt the top rail inside the support in order to get your cage with a superior border (solution 2). Try it! 63-1109TR COMPLETE TOP RAIL 1079×907 mm 63-1409TR COMPLETE TOP RAIL 1432,5×907 mm 63-1410TR COMPLETE TOP RAIL 1432,5×1097 mm 63-1412TR COMPLETE TOP RAIL 1432,5×1287 mm 63-1710TR COMPLETE TOP RAIL 1786×1097 mm 63-1712TR COMPLETE TOP RAIL 1786×1287 mm
black aluminium black aluminium black aluminium black aluminium black aluminium black aluminium
63-1714TR COMPLETE TOP RAIL 1786×1477 mm 63-1914TR COMPLETE TOP RAIL 1950×1477 mm 63-2112TR COMPLETE TOP RAIL 2139,5×1287 mm 63-2114TR COMPLETE TOP RAIL 2139,5×1477 mm 63-2414TR COMPLETE TOP RAIL 2493×1477 mm 63-2814TR COMPLETE TOP RAIL 2846,5×1477 mm
black aluminium black aluminium black aluminium black aluminium black aluminium black aluminium
45 mm
Solution 1.
Solution 2.
PROFILES FOR UPPER FRAME - PARTS AND ACCESSORIES To customize your UPRACKS roof rack, you can fit a full or partial upper frame. The list here below shows several possibilities to achieve the most suitable configuration to your needs. The exploded-view drawing shows components in detail to provide a better understanding and make sure you purchase the correct components for your configuration. Component table 63-ASR100 63-ASR120 63-ASR150 63-ASR200 63-ASRQ 63-ASR75 63-ASR56 63-ASR37 63-ASRFITS2
PROFILE WITH 3 GROOVES - 1.00 m - pair, black PROFILE WITH 3 GROOVES - 1.20 m - pair, black PROFILE WITH 3 GROOVES - 1.50 m - pair, black PROFILE WITH 3 GROOVES - 2.00 m - pair, black FRAME CURVE - pair, black FRONT PROFILE -75 cm - suitable for 1477 cm width, black FRONT PROFILE -56 cm - suitable for 1287 cm width, black FRONT PROFILE -37 cm - suitable for 1097 cm width, black FRAME SUPPORT / CONNECTOR - pair, black
63-ASR100P 63-ASR120P 63-ASR150P 63-ASR200P 63-ASRQP 63-ASR75P 63-ASR56P 63-ASR37P 63-ASRFITS2
Front profiles and frame curves are available in black colour powder coating or aluminium. Notes: • All the components can be ordered in natural aluminium colour or black coated. • Side profiles of length 100/120/150/200 cm are sold as a pair and the package contains: - 2x profiles of the length selected - 4x black nylon end caps - 6x black supports /connectors (63-ASRFITS2) - 24x rectangular nuts with bolts as required for attachment to the roof rack • Front (or back) profiles are cut to measure in order to match the three different widths available for UPRACKS roof racks and to be connected to curved profiles. They are sold as single pieces and the package contains: - 1x profile of the length selected
PROFILE WITH 3 GROOVES - 1.00 m - pair, polished PROFILE WITH 3 GROOVES - 1.20 m - pair, polished PROFILE WITH 3 GROOVES - 1.50 m - pair, polished PROFILE WITH 3 GROOVES - 2.00 m - pair, polished FRAME CURVE - pair, polished FRONT PROFILE -75 cm - suitable for 1477 cm width, polished FRONT PROFILE -56 cm - suitable for 1287 cm width, polished FRONT PROFILE -37 cm - suitable for 1097 cm width, polished FRAME SUPPORT / CONNECTOR - pair, black
Profiles are available in black colour powder coating or aluminium. •
- 3x black supports /connectors (63-ASRFITS2) - 12x rectangular nuts with bolts as required for attachment to the roof rack Curved profiles (63-ASRQ), which serve as angle pieces, are standard in section; their final width will be determined by the front profile selected to allow combination with your UPRACKS roof rack. They are sold as a pair and the package contains: - 2x curved profiles - 4x black nylon end caps - 4x black supports /connectors (63-ASRFITS2) - 16x rectangular nuts with bolts as required for attachment to the roof rack
w w w. u p r a c k s . c o m 4
ACCESSORIES
63-A001 LIFTING EYE
Thanks to the standard size profiles of our UPRACKS roof racks, the lifting eyes can be slid into all the channels and can be tightened by the special rectangular bolt 63-A002.
63-A00202 ANCHOR PLATE/SQUARE NUT - 20 mm, STANDARD 63-A002 ANCHOR PLATE/RECTANGULAR NUT - 40 mm
By a simple sliding mechanism (“slide-in-all” system) this special rectangular nut (pitch M8) allows locking any of our accessories; thanks to its shape it can be easily placed into the specific rails and its special design provides a larger resting surface, thus increasing its tearing resistance.
63-A003 PORTABLE TELESCOPIC LADDER
In our opinion, the best solution to climb onto the vehicle’s roof is to use a ladder that rests on the ground. This is to ensure a better safety level when you need to climb onto the roof and to provide more flexibility to all the vehicles’ owners, who need a ladder suitable for their specific vehicle height from the ground. Once the telescopic ladder has been folded, it can be tied to the roof rack or stored in the luggage boot. It weighs only 7 Kg and reaches 260 cm in height. You may also use it at your house.
63-ALRL REAR LADDER FOR LAND ROVER DEFENDER
Using the same UPRACKS roof racks frames, we’ve designed a simple alloy ladder that fits on the rear left side of LR Defender. Powder coated in black with 3 steps. This ladder can be bolted on the vehicle body as showed in the pictures.
63-ALRLSET REAR LADDER FOR LAND ROVER DEFENDER WITH ESTENSION
Using, as a base, the ladder 63-ALRL, we add an extension with 3 more steps that permits, with special skids, to slide it down for over 60 cm. When closed and locked on its base this extension do not cause any interference with the vehicle car plate.
63-A004 WHEEL CARRIER
Simple and easy to use, it has been designed such that it doesn’t need to be permanently attached to the roof. A special asymmetric “C” shaped plate holds the roof rack cross bar. Once the wheel has been positioned, the resin cone-shape member centres the wheel rim hole and the throttle bolt fully tightens against the rod, thus creating a pull-clamping. This system allows, first, safely positioning the wheel onto the roof rack and then anchor it in the most suitable position to your needs, by using this special clamping system. The metal material used for this accessory is stainless steel.
63-A005X ADJUSTABLE SINGLE JERRY CAN HOLDER
This jerry can holder allows positioning a single jerry can onto the roof rack. It can be fitted both longitudinally and transversely in order to facilitate and optimize weight distribution on the roof rack. The single jerry can holder kit can be combined to other jerry can holders by means of a connection member. In this way it is possible to have multiple jerry can holders which are perfectly interconnected and bolted to the roof-rack. The jerry can holder has specific holes to allow fitting an anti-theft padlock (not provided).
63-A006 UNIVERSAL RUBBER/LEVER CLAMP KIT
The kit consists of a pair of rubber supports that can be fitted by the rectangular nut in any position by using the channels (slots) of our UPRACKS roof rack. A robust rubber strap assures proper attachment. 63-A0066 Ø up 15 mm to 34 mm 63-A0067 Ø up 25 mm to 63 mm 63-A0068 Ø up 44 mm to 73 mm 63-A0069 Ø up 69 mm to 88 mm
63-A007 LIFT JACK HOLDER x3
A simple and extremely resistant system for attaching Hi-Lift jack to UPRACKS roof rack in the safest and fastest way. The kit consists of 3 supports especially designed to enable the operator to safely lean the lift jack; after this operation, he/she will have his/her hands free to anchor it to the roof rack. In order to bear the lift jack weight (more than 12 Kg), the 3 single supports are equipped with 5 nuts and respective steel bolts to be attached to the frame of our UPRACKS roof rack. The lift jack is locked to the support by a knob pin.
63-A010 LIGHT/ AERIAL MOUNT BRACKET
The kit consists of a pair of supports that can be attached to any point of the perimeter frame of UPRACKS roof rack, either downward or upward. It can also be used as a universal support and as an aerial mount bracket. It can be fitted by 2 rectangular nuts and respective bolts (included in the kit).
ACCESSORIES
w w w. u p r a c k s . c o m 5
63-A011 AWNING KIT / LONG SUPPORT
The kit consists of a pair of supports to be attached to the perimeter frame of UPRACKS roof rack. It is a Heavy Duty support, because it must be attached by 5 rectangular nuts and bolts. We called it “Awning Kit”, but it is an excellent support to carry and attach any equipment. Maximum load capacity recommended: 15 Kg, to be distributed on the 2 supports.
63-A0111 AWNING KIT / SUPPORT
This new awning bracket is designed in two pieces to permit to fit the side awning outside or inside the Upracks roofrack. Sliding in and out following your own necessity. For ex., as showing in the pictures below, if you have a complete top rail or you have loaded on the cage big volumes and you don’t have enough space, with this system you can go over size! This bracket is especially designed to fit any awning brand.
63-A012 ALUMINIUM PLATE PAIR
Set of aluminium sand plates, in red colour coating. Size 120 x 40 cm. Weight: 11.5 Kg.
63-TRAX1400 SAND TRACK
Sand track in plastic material. Extremely flexible, light and elastic. Great alternative to heavy and bulky metal tracks. Helps to get past the obstacle or if you find yourself in a slippery situation. Very competitive price. Size: 1400x290x 30 mm (height). Weight: 2.5 Kg.
63-ASRFITS2 SUPPORT / CONNECTOR
“S” shaped supports with bolts and inserts as required for attachment of the top rail onto roof-rack. It is mainly used as a support and connection member for the roof-rack upper frame (top rail) but it can also be employed to lock the load onto the roof- rack or support accessories. Made of steel, powder-coated black colour.
63-A014 PLATE HOLDER
It consists of a pair of supports to be attached to the roof rack frame by 4 rectangular nuts and respective bolts. Every support is provided with: 1 washer, 1 resin cone-shape member and 1 special key to tighten nuts. The special resin cone-shape member makes it adaptable to any hole from min 30 mm to max 120 mm. Key, nuts and attachment kit, all included in the package.
63-A015 MAGNET FOR ANCHOR PLATE/RECTANGULAR NUT
This simple micro-magnet allows easy removal of the rectangular nut from channels (slots) of UPRACKS roof rack.
63-A016 THIN RUBBER STRIP TO AVOID WIND NOISE (sold by meter)
Especially designed and manufactured for UPRACKS, this PVC strip is provided as three standard pieces of 160 cm length and is included in our UPRACKS roof rack package. Its special design helps avoiding possible noise. It allows covering any slot in the frame (on its top, bottom, inner and outer side). It can be simply fitted to the roof rack for a more attractive look. Black colour.
63-A017 ANTI-SLIP WIDE RUBBER STRIP (sold by meter)
Especially and exclusively designed and manufactured for UPRACKS, this pebble-like PVC strip is provided by meter and mainly serves to cover the upper slots in the roof rack in order to have a better grip on the usable upper part. It can be fitted to the outer side of the perimeter frame for a more attractive look. Black colour.
63-A08787 ALUMINIUM ANGLE PIECE (PAIR)
Pair of melt aluminium angle pieces to provide a firm load stabilization; they can also be employed in overhanging position as a support. They can be used in any position and are provided with respective rectangular nuts and bolts. They are 8.7 cm (each side), and 8.7 cm thick.
63-A04387 ALUMINIUM ANGLE PIECE (PAIR) They are 8.7 cm (each side), and 4.3 cm thick.
63-A04343 ALUMINIUM ANGLE PIECE (PAIR) They are 4.3 cm (each side), and 4.3 cm thick.
w w w. u p r a c k s . c o m 6
ACCESSORIES
63-A019 UPRACKS UTILITY/CAMP TABLE
Designed to bear more than 80 Kg weight, the table is fully made of aluminium having a honeycomb structure. The table top is made of a stainless steel foil which makes it easy to be cleaned. Once it is folded, the table is 3.4 cm thick. It weighs only 10 Kg. Size: 144x69x h 70 cm. The table mount kit (63-A018) is optional.
63-A018 UPRACKS TABLE MOUNT KIT (optional)
The set consists of two L-shaped supports to be attached to the lower part of the roof rack. In this way, once UPRACKS table has been folded, it can slide in these specific rails and be locked by two especially designed locking members.
63-A0191 UPRACKS UTILITY/CAMP TABLE - LIGHT (coming soon)
Designed to bear more than 45 Kg weight, this lightweight table is fully foldable. It folds up to become 1/3 of its open size. Frame fully made of aluminium. Table top in multi-layer wood with protective treatment. Special hinges and legs. Once it is folded, the table is 10 cm thick. It weighs only 8 Kg. Size open: 110x70x h 73 cm. Size closed: 110x25x h 10 cm. Two different options to hold it on roof-rack: 63-WT50SFK if you want fit it on the top of the roof-rack 63-A014 to hold it on the external frame of the roof-rack
63-AROL ROLLER
Roller to facilitate loading accessories onto the roof rack. Size: 680 mm. Available in different lengths (upon request).
63-A023 WALKABLE PLATFORM
If you wish to create a robust and resistant walkable platform that partially or fully occupies the surface of your UPRACKS, this is the easiest and most effective solution. The kit is composed of 2 pieces in almond-pattern aluminum available in multiple modules and attachable into the grooves of the roof-rack cross-bars by means of rounded-head bolts. By this system you can build up and customize a resistant platform that can be extended on the entire surface, or just partially on some areas of the roof-rack, where you need to have a walkable area. Each plate is 50 cm long and 19 cm wide.
63-WT50S WATER TANK - 50 LITRES - SLIM
Simple slim water tank with a new design 1230 mm long, 600 mm width and only 8.2 mm height. Capacity 50 litres.
63-WT50SFK WATER TANK FITTING KIT The specific fitting kit totally in stainless steel.
63-WT20 20-LITRE JERRY CAN
Plastic jerry can for water. Capacity: 20 litres. Size: 350x170x470 mm. Weight 2.5 Kg Fits on 63-A005X.
63-A009 UNIVERSAL IRON WIND FAIRING
It has been designed to stop wind noise and reduce fuel consumption. This fairing can be fitted to UPRACK roof racks in just a few minutes by using 3 attachment points. It can be fitted at the front or rear of the vehicle and the flap can be upward or downward facing. 2 fairings can be fitted thus diffusing air both upward and downward. The fairing is sold as a single piece in a package including nuts and bolts.
63-A0091 ABS WIND FAIRING Width 120 cm - Suitable for 1097 cm width roof-racks 63-A0092 ABS WIND FAIRING Width 112 cm - Suitable for 1287 cm width roof-racks 63-A0093 ABS WIND FAIRING Width 132 cm - Suitable for 1477 cm width roof-racks
63-AC45 ALUMINIUM BOX
Exclusively designed for UPRACKS, this aluminium box has some important characteristics: metal sheet thickness: 1.2 mm; cover rubber gasket and inner seal which protects the box content from weathering agents; net capacity: 45 litres. Size: 78.2x38.5 cm, height being only 19 cm to minimize aerodynamic impact. Weight: 4.2 Kg.
ATTACHMENT KIT
63-FK001B Leg kit pair height from 12 to 16 cm. 63-FK002B Leg kit pair height from 16 to 20 cm. 63-FK003B Leg kit pair height from 20 to 26 cm. 63-FK004B Leg kit pair height from 26 to 31 cm.
w w w. u p r a c k s . c o m 7
63-FEST INNER EXTENSION FOR UPRACKS LEGS - PAIR
If you do not wish to fit the single leg on the single axle line of the crosspiece, you can use the specific designed optional adapter for attaching the leg inside the roof rack frame. The two pictures illustrate fitting operations. Sold as a pair with respective nuts and bolts.
The package contains a pair of leg kits and is provided with all that is needed for permanent attachment of each single leg to the roof rack. Every kit is equipped with: - 2x complete legs as in the picture (the picture only shows one leg and its components) - 6x rectangular nuts with respective steel bolts for attachment to the roof rack - 1x magnet to remove rectangular nuts from their slots - 2x powder-coated, cataphoresis-treated iron* attachment cover plate with rubber pads - 2x Allen head bolts for attachment to the gutter rail by the steel cover attachment plate - 2x threaded plates and 4 bolts for leg assembly. *The same kits can be provided upon request with STAINLESS steel attachment covers.
63-FKR “C” ADAPTER TO RHINO RACK LEGS - PAIR
63-FKRAIL PLATE KIT TO BE FITTED BETWEEN CROSSBARS - PAIR (to be combined with 63-FKR if Rhino-Rack legs are used)
Adapter (2 pieces) which allows fitting and adapting UPRACKS roof rack to any vehicle by using any leg kits commercially available. We have especially designed this adapter to combine the specific leg kits manufactured by famous Rhino-Rack to our roof rack. In fact Rhino-Rack offers a great number of fitting kits for all those 4x4, SUV and Crossover vehicles having fixed attachment points on the roof and thus requiring specific applications. This kit consists of a connection bridge between crosspieces (see picture) and allows our UPRACKS roof rack to be easily adapted and connected to Rhino-Rack (or other) legs and hence to the roof. A further advantage provided by this system is that you can choose a wider or longer-size roof rack than the standard one and you can position it more forward or backward according to your needs. In fact, the adapter is attached by our rectangular bolts and can slide into the roof rack cross bar. Following are some impressive examples of our solution. Important: if Rhino-Rack legs are used you need to purchase the special adapter 63-FKR. The package includes 2 adapters, 4 rectangular nuts and respective bolts, and magnet. The adapter pair serves for one leg pair.
The kit is provided as a pair and serves to attach the classic gutter mount legs of famous RhinoRack Heavy Duty version to any UPRACKS roof racks. Rhino-Rack legs are in plastic material and your choice may be due to aesthetic reasons, reduced load needs or just because you already possess Rhino kit but you need to fit a different roof rack or to replace your existing simple load bars. Kit 63-FKR is provided in a package with 2 adapters, 6 rectangular nuts, one magnet and steel nuts and bolts. Note: this particular “C” adapter also enables you to attach Rhino-Rack Heavy Duty leg kit designed for each single vehicle having roof fixed anchor points and having no gutter rails to UPRACKS roof rack. Visit our website periodically to see pictures and specific applications.
8
SPECIAL KITS
w w w. u p r a c k s . c o m
63-FKJ15J12 FITTING KIT FOR TOYOTA PRADO 150/125
This specific fitting kit is a valid alternative to fit our UPRACKS roof rack on Toyota Prado J150/ J120/J125 without using specifics legs kit from RhinoRack. This new way to fit is really heavy duty. This kit includes: 6 x 63-FKRAIL (totals 12 plates to be fitted between crossbars) 3 x 63-FK001 (total 3 pair of legs without foot base) 6 x roof adapter (special foot bases) This kit suits perfectly UPRACKS roof racks p/n 63-2112, 63-2112P, 63-1712 and 63-1712P.
63-FKJK2 COMBO FITTING KIT FOR WRANGLER JK 2 DOORS (roof-rack not included). 63-FKJK4 COMBO FITTING KIT FOR WRANGLER JK 4 DOORS (roof-rack not included).
Special design, nice looking and very heavy duty system to load over 150 Kg without any drill. This external roll-bar permits to fit the right Upracks roof-rack (see on the web the application chart) on hard top and soft top Jeep Wrangler Unlimited from 2007 on. Easy to install, because the front bar is attached by a base on the OEM wind-shield outer frame. The rear bar is bolted on special C clamps with bushes and then attached by a special, strong braket to the OEM under body frame. When mounted, you can use it like it is or you can clamp on the cross member bars our Upracks roof-rack with the size you prefer. The weight of the combo fitting kit is 37 Kg made in steel and cataphoresis treated then powder-coated epoxy in black colour.
63-FKPANDA SET LEG KIT FOR NEW FIAT PANDA 2012 ON.
This heavy duty leg system suits in combination with a special designed Upracks roof-racks. On the original vehicle rails, the special legs are fitted in correspondence of four pre-marked point of the OEM rails. Each clamps, when tied on the rails, becomes a unique strong fixed point where you can bolt the roof-rack. The special designed Upracks cage is 63-1409 with size 1432,5Ă—907 mm. With this system you can slide the roof-rack more forward or less following your own necessity. The weight capacity of the complete system is over 70 Kg but you must follow the car maker guide that says max load 60 Kg.
For more informations and details visit www.upracks.com
Š 2012. It is prohibited to reproduce, even partially, texts and images in this leaflet without prior written consent of 4Technique. May 2014
9
www.upracks.de
w w w. u p r a c k s . c o m 10
MODELLE
Die Standart-Version ist schwarz pulverbeschichtet. Pulverbeschichtete Naturaluminiumversion ebenfalls verfügbar.
Die UPRACKS-Gepäckträger sind so gestaltet, dass sie den Anforderungen an eine Gepäckplattform optimal entsprechen. Die zur Verfügung stehenden Größen ermöglichen eine Montage auf alle gängigen Geländewagen, Pickups, SUVs, usw. Derzeit sind es acht verschieden lange bzw. breite Träger, welche ein äußerst breites Einsatzspektrum abdecken. Es genügt, die Nutzfläche des eigenen Autodachs zu messen und in der Tabelle die passende Größe unserer Träger zu suchen. Die UPRACKS-Gepäckträger sind aus einer speziellen Aluminiumlegierung gefertigt, welche auf dem höchsten Punkt des Fahrzeugs - dem Dach - eine satte Gewichtsersparnis bietet. Diese fehlenden Kilos, im Vergleich zu ähnlichen Konstruktionen aus Stahl, machen sich nicht nur bei der Montage und „Leerfahrten“ bemerkbar, sie ermöglichen auch, die ohnehin begrenzte Dachlast bestmöglich auszunutzen. In der Bedienungsanleitung des Fahrzeugherstellers wird üblicherweise die zulässige Dachlast genau angegeben und es ist wichtig, sich strikt an diese Angabe zu halten. UPRACKS ist in der Lage, Gepäckplattformen mit einem Gewicht von nur 14 bis 34 kg - je nach Größe - zu fertigen. Hier ein Beispiel zur Berechnung der Nutzlast: Wenn ein Fahrzeughersteller eine Traglast von 100 kg angibt, erhält man die Nutzlast durch Abziehen des Gepäckträgergewichts inkl. Fußsatz und Anbauteile; d.h. bei einem 25 kg schweren Aluminium-Gepäckträger-System kann man das Dach mit bis zu 75 kg Material beladen; bei einem StahlGepäckträger wäre das Eigengewicht bis zu dreimal so hoch, d.h. 75 kg, so dass sich die Nutzlast auf nur 25 kg verringern würde! Die UPRACKS-Gepäckträger werden mit spezifischen Fußsätzen befestigt und sind für Fahrzeuge mit und ohne Regenrinne konzipiert. In den Fällen, in denen die Befestigung nicht durch die UPRACKS Regenrinnen-Fußsätze erfolgen kann, liefern wir Lösungen aus den zahlreichen Anbausystemen des bekannten, australischen Dachträgerherstellers Rhino Rack. Sämtliche Profile - die des Rahmens, der Querstreben und der Planken - haben die gleiche Nut. Dies ermöglicht, dass Zubehör und andere Ausrüstungsgegenstände mit einer größtmöglichen Flexibilität angebaut werden können. Rechteckige Nutensteine mit M8 Gewinde können in das „Slide-In-All“-System beliebig eingeschoben werden und dienen so als variable Aufnahmepunkte. Die UPRACKS-Gepäckträger, Fußsätze und Zubehörteile werden zuerst kataphoretisch behandelt und anschließend schwarz pulverbeschichtet. Auf Anfrage können wir die Gepäckträger auch unbehandelt, d.h. aus poliertem Naturaluminium liefern. Bei aller Liebe zum Dachgepäckträger möchten wir darauf hinweisen, dass besonders schwere Teile nicht auf dem Dach, sondern möglichst weit unten im und am Fahrzeug transportiert werden sollten, da sich andernfalls der Schwerpunkt des Fahrzeugs - zu Ungunsten des Fahr- und Kippverhaltens nach oben verlagert. Zudem sind alle Zubehör-, Anbau- und Ausrüstungsteile, sowie mitgenommenes Gepäck stets bestens zu sichern. CODES, GRÖSSEN UND AUSFÜHRUNGEN 63-1109 1079×907 mm Aluminium schwarz 63-1109P 1079×907 mm Aluminium poliert 63-1409 1432,5×907 mm Aluminium schwarz 63-1409P 1432,5×907 mm Aluminium poliert 63-1410 1432,5×1097 mm Aluminium schwarz 63-1410P 1432,5×1097 mm Aluminium poliert 63-1412 1432,5×1287 mm Aluminium schwarz 63-1412P 1432,5×1287 mm Aluminium poliert
63-1710 1786×1097 mm 63-1710P 1786×1097 mm 63-1712 1786×1287 mm 63-1712P 1786×1287 mm 63-1714 1786×1477 mm 63-1714P 1786×1477 mm 63-1914 1950×1477 mm 63-1914P 1950×1477 mm
Aluminium schwarz Aluminium poliert Aluminium schwarz Aluminium poliert Aluminium schwarz Aluminium poliert Aluminium schwarz Aluminium poliert
63-2112 2139,5×1287 mm 63-2112P 2139,5×1287 mm 63-2114 2139,5×1477 mm 63-2114P 2139,5×1477 mm 63-2414 2493×1477 mm 63-2414P 2493×1477 mm 63-2814 2846,5×1477 mm 63-2814P 2846,5×1477 mm
Aluminium schwarz Aluminium poliert Aluminium schwarz Aluminium poliert Aluminium schwarz Aluminium poliert Aluminium schwarz Aluminium poliert
RELING
w w w. u p r a c k s . c o m 11
RELING (TR) Für alle die eine komplette Reling, welche passgenau dem äußeren Rahmen der Gepäckplattform folgt, haben möchten, bieten wir jetzt dieses Komplettset an. Es besteht aus vorderen, hinteren und seitlichen Rahmen, vier Eckstücken, Relingfüßen (63-ASRFITS2) und allem nötigen Montageteilen. Um den Bestellprozess möglichst einfach zu gestalten, wird einfach das Kürzel TR an die Bestellnummer des Trägers angehängt. z.B. 63-1410 (Träger) benötigt eine 63-1410TR (Reling). Die Relingfüße 63-ASRFITS2 können pärchenweise bestellt und beliebig ergänzt werden. Besonders! Für noch mehr Individualität kann die Reling in zwei verschiedenen Weisen montiert werden. Bei der ersten wird die Reling auf den Füßen montiert und hat ca. 45mm Abstand zur Plattform (1). Bei der Anderen wir die Reling in die Füße montiert, liegt auf der Plattform auf, und ist somit als flacher Rahmen zu betrachten (2). 63-1109TR COMPLETE TOP RAIL 1079×907 mm 63-1409TR COMPLETE TOP RAIL 1432,5×907 mm 63-1410TR COMPLETE TOP RAIL 1432,5×1097 mm 63-1412TR COMPLETE TOP RAIL 1432,5×1287 mm 63-1710TR COMPLETE TOP RAIL 1786×1097 mm 63-1712TR COMPLETE TOP RAIL 1786×1287 mm
Aluminium schwarz Aluminium schwarz Aluminium schwarz Aluminium schwarz Aluminium schwarz Aluminium schwarz
63-1714TR COMPLETE TOP RAIL 1786×1477 mm 63-1914TR COMPLETE TOP RAIL 1950×1477 mm 63-2112TR COMPLETE TOP RAIL 2139,5×1287 mm 63-2114TR COMPLETE TOP RAIL 2139,5×1477 mm 63-2414TR COMPLETE TOP RAIL 2493×1477 mm 63-2814TR COMPLETE TOP RAIL 2846,5×1477 mm
Aluminium schwarz Aluminium schwarz Aluminium schwarz Aluminium schwarz Aluminium schwarz Aluminium schwarz
45 mm
Lösung 1.
Lösung 2.
RELING - TEILE UND ZUBEHÖRTEILE Um den UPRACKS-Gepäckträger individuell anpassen zu können, besteht die Möglichkeit, Komplett- oder Teilrelings anzubauen. Die unten aufgeführte Liste zeigt die verschiedenen Bauteile, mit denen es möglich ist, unterschiedlichste Varianten zusammenzustellen. Die Abbildungen zeigen Beispiele der einzelnen Bauteile. Tabelle der Bauteile 63-ASR100 63-ASR120 63-ASR150 63-ASR200 63-ASRQ 63-ASR75 63-ASR56 63-ASR37 63-ASRFITS2
RELING 3 NUTEN - 1,00 m - Paar, schwarz RELING 3 NUTEN - 1,20 m - Paar, schwarz RELING 3 NUTEN - 1,50 m - Paar, schwarz RELING 3 NUTEN - 2,00 m - Paar, schwarz ECKSTÜCK - Paar, schwarz FRONT/HECK RELING -75 cm - geeignet für 1477 cm breite, schwarz FRONT/HECK RELING -56 cm - geeignet für 1287 cm breite, schwarz FRONT/HECK RELING -37 cm - geeignet für 1097 cm breite, schwarz RELINGFUß / VERBINDUNGSSTÜCK - Paar, schwarz
Die Front/Heck-Reling und die Eckstücke sind schwarz pulverbeschichtet oder in der Aluminium-Ausführung erhältlich. Hinweise: • Alle Bauteile können in Aluminium pur oder schwarz beschichtet bestellt werden. • Die Seitenprofile von 100/120/150/200 cm Länge werden paarweise geliefert. Die Packung enthält: - 2 Stk. Reling in der vorgegebenen Länge - 4 Stk. schwarze Nylonverschlussstopfen für das Endteil - 6 Stk. Trägerfuß / Verbindungsstück schwarz (63-ASRFITS2) - 24 Stk. rechteckige Muttern mit entsprechenden Schrauben zur Befestigung auf dem Gepäckträger • Die Front/Heck-Relings sind passend für die drei verschiedenen Breiten der UPRACKS- Gepäckträger angefertigt - sie können mit den Eckstücken zu einer umlaufenden Reling verbunden werden. Sie werden einzeln geliefert; die Packung enthält:
63-ASR100P 63-ASR120P 63-ASR150P 63-ASR200P 63-ASRQP 63-ASR75P 63-ASR56P 63-ASR37P 63-ASRFITS2
RELING 3 NUTEN - 1,00 m - Paar, poliert RELING 3 NUTEN - 1,20 m - Paar, poliert RELING 3 NUTEN - 1,50 m - Paar, poliert RELING 3 NUTEN - 2,00 m - Paar, poliert ECKSTÜCK Paar, poliert FRONT/HECK RELING -75 cm -geeignet für Breite 1477 cm, poliert FRONT/HECK RELING -56 cm -geeignet für Breite 1287 cm, poliert FRONT/HECK RELING -37 cm -geeignet für Breite 1097 cm, poliert RELINGFUß / VERBINDUNGSSTÜCK - Paar, schwarz
Die Front/Heck-Reling und die Eckstücke sind schwarz pulverbeschichtet oder in der Aluminium-Ausführung erhältlich. - 1 Stk. Reling in der vorgegebenen Länge - 3 Stk. Trägerfuß / Verbindungsstück schwarz (63-ASRFITS2) - 12 Stk. rechteckige Muttern mit den entsprechenden Schrauben zur Befestigung auf dem Gepäckträger • Die Eckstücke (63-ASRQ) haben dieselben Nuten wie die geraden Relings; von der Auswahl des Frontalprofils hängt die Endbreite ab, damit dieses mit dem eigenen UPRACKS-Gepäckträger kombiniert werden kann. Sie werden paarweise geliefert und die Packung enthält: - 2 Stk. Eckstücke - 4 Stk. schwarze Verschlussstopfen für das Endteil - 4 Stk. Trägerfuß / Verbindungsstück schwarz (63-ASRFITS2) - 12 Stk. rechteckige Muttern mit entsprechenden Schrauben zur Befestigung auf dem Gepäckträger
w w w. u p r a c k s . c o m 12
ZUBEHÖRTEILE
63-A001 AUGENSCHRAUBE
Dank der standardisierten Größe der Nuten unserer UPRACKS-Gepäckträger können die Augenschrauben in alle Kanäle verschoben und mit den dafür vorgesehenen rechteckigen Muttern 63-A002 befestigt werden.
63-A00202 ANKERPLÄTTCHEN/4-KANT MUTTER - 20 mm, SERIENMÄSSIG 63-A002 ANKERPLÄTTCHEN/RECHTECKIGE MUTTER - 40 mm
Mit Hilfe des einfachen „Slide-In-All“-Systems dient diese spezielle Mutter (Steigung M8) als Ankerpunkt für die unterschiedlichsten Anbauteile. Sie kann in jede Nut des Dachgebäckträgers eingelegt werden und verfügt über eine möglichst große Auflagefläche.
63-A003 AUSZIEHBARE TRAGLEITER
Unseres Erachtens nach ist die beste Lösung, um auf den Gepäckträger zu gelangen, eine auf dem Boden stehende Leiter. Wird die Teleskopleiter geschlossen, kann diese leicht auf dem Gepäckträger verzurrt oder im Innenraum verstaut werden. Sie wiegt nur 7 kg und erreicht ausgezogen eine Höhe von 260 cm. Zudem kann sie auch Zuhause praktisch verwendet werden.
63-ALRL LEITER LAND ROVER DEFENDER (HINTEN)
Unter Verwendung des gleichen Profils, wie das des Dachträgers, haben wir eine Leiter gebaut, die Perfekt an die linke Seite des Hecks des Defenders passt. Sie kommt schwarz Pulverbeschichtet mit 3 Stufen. Die Leiter kann wie auf den Bildern zu sehen, an das Fahrzeug geschraubt werden.
63-ALRLSET LEITER FÜR LAND ROVER DEFENDER HECK MIT ERWEITERUNG
Auf Basis der Leiter 63-ALRL wurde eine Erweiterung mit 3 weiteren Stufen entwickelt, die es erlaubt, mit speziellen Schienen die Leiter über 60cm nach unten zu ziehen. Eingefahren, beeinträchtigt sie das Nummernschild in keiner Weise.
63-A004 RADHALTER
Der Radhalter kann je nach Bedarf schnell an- und abgebaut werden. Seine C-förmige Klammer umschließt einfach einen Querträger der Plattform. Nachdem das Rad positioniert ist, zentriert sich der Kunstharzkegel in dem Felgenloch und mittels der Flügelmutter wird das Rad gesichert. Das tolle an diesem System ist, dass erst das Rad auf dem Dachgepäckträger positioniert werden kann und dann die Montage des Radhalters erfolgt. Der Halter ist aus Edelstahl gefertigt.
63-A005X KANISTERHALTER EINZELN MODULBAUWEISE
Dieser Kanisterhalter ermöglicht, einen einzelnen Kanister auf dem Gepäckträger zu positionieren. Er kann längs oder quer montiert werden, um die optimale Gewichtsverteilung zu erreichen. Die einzelnen Kanisterhalter können mit anderen durch Verbindungsstücke kombiniert werden. Auf diese Weise kann jeder selbst bestimmen, wie viele Kanister nebeneinander transportiert werden. Sie können miteinander verschraubt werden. Spezifische Löcher können zur Verwendung eines Vorhängeschlosses (nicht im Lieferumfang enthalten) genutzt werden.
63-A006 UNIVERSAL HALTERSYSTEM MIT HEBEL
Der Satz (2) besteht aus verzinkten Ankerplatten, die in jeder Position montiert werden können. Kräftige Gummis bieten eine optimale Befestigung für Äxte, Schaufeln, usw. 63-A0066 Ø up 15 mm to 34 mm 63-A0067 Ø up 25 mm to 63 mm 63-A0068 Ø up 44 mm to 73 mm 63-A0069 Ø up 69 mm to 88 mm
63-A007 HI-LIFT-HALTER x3
Ein robustes System, mit dem der Hi-Lift so sicher und einfach wie möglich auf dem UPRACKS-Gepäckträger befestigt werden kann. Der Satz besteht aus 3 Haltevorrichtungen, auf welche der Hi-Lift erst abgelegt und dann befestigt wird. Um das Gewicht des Hi-Lifts (über 12 kg) und die dadurch entstehenden Kräfte besser an die Plattform weiterleiten zu können, werden die Halter sowohl seitlich, wie auch oben auf der Plattform verschraubt.
63-A010 SCHEINWERFER-/ANTENNENHALTER
Die Scheinwerferhalter können an jedem Punkt am Außenrahmen des UPRACKS-Gepäckträgers sowohl nach unten, als auch nach oben gedreht befestigt werden. Sie sind auch als Universal- oder Antennenhalter verwendbar. Sie werden paarweise mit entsprechendem Montagezubehör geliefert.
ZUBEHÖRTEILE
w w w. u p r a c k s . c o m 13
63-A011 LANGE UNIVERSALHALTERUNG
Auch die langen Universalhalterungen kommen paarweise und werden am Außenrahmen des UPRACKSGepäckträgers mehrfach verschraubt. Ihre solide Konstruktion erlaubt es, dass Sie mit bis zu 15 kg (das Paar) beladen werden dürfen.
63-A0111 MARKISENHALTER
Das zweiteilige Design des Markisenhalters ermöglicht, ein Markise außer- oder innerhalb der Fläche des Upracks Gepäckträgers zu montieren. Die Wunschposition kann nach persöhnlichen Bedürfnissen gewählt werden. Z.B. kann wie auf den Bildern untern gezeigt die Halterung über den Rand der Plattform hinaus versetzt werden, sollte eine komplette Reeling, oder ein Dachzelt montiert sein. Der Halter wurde so entworfen, dass alle Markisen angeschraubt werden können.
63-A012 SANDBLECHE ALUMINIUM
Satz (2) Sandbleche aus Aluminium, rot lackiert. Größe 120 x 40 cm. Gewicht: 11,5 kg.
63-TRAX1400 SANDBLECHE
Sandblech aus Plastik. Extrem flexibel, leicht und elastisch. Großartige Alternative zu schweren und sperrigen Metallblechen. Hilft, über ein Hindernis zu kommen oder wenn man sich in einer rutschigen Situation befindet. Sehr fairer Preis. Größe: 1400x290x30mm (Höhe) Gewicht: 2,5kg
63-ASRFITS2 RELINGFUß / VERBINDUNGSSTÜCK
“S”-förmige Träger welche benötigt werden, um die Reling auf die Gepäckplattform zu montieren. Neben ihrer Funktion als Träger für die Reling können sie auch als Element zu Ladungssicherung verwendet werden. Gefertigt aus Stahl mit schwarzer Pulverbeschichtung.
63-A014 SANDBLECHHALTER
Der Sandblechhalter wird mehrfach am Außenrahmen verschraubt und kann verschiedene Bleche aufnehmen. Der Kunstharzkegel passt in Löcher mit einem Durchmesser von 30 mm – 120 mm. Schlüssel, Muttern und Befestigungssatz sind in der Packung enthalten.
63-A015 MAGNET FÜR ANKERPLÄTTCHEN/RECHTECKIGEN MUTTERN
Mit dem Mikromagneten können die rechteckigen Muttern einfach aus den Nuten des UPRACKS-Gepäckträgers „gefischt“ werden.
63-A016 DÜNNE DICHTUNG ZUR GERÄUSCHUNTERDRÜCKUNG (in Laufmeter lieferbar)
Diese PVC-Dichtung wurde speziell für uns gestaltet und hergestellt; serienmäßig werden 3 Stück je 160 cm lang in der Packung des UPRACKS-Gepäckträgers mitgeliefert. Das Design dient zur Geräuschunterdrückung. Jede Nut kann geschlossen werden (oben, unten, auf der Seite und in der Mitte). Die Dichtung kann auch einfach zur Verbesserung der Optik montiert werden. Farbe schwarz.
63-A017 BREITE RUTSCHFESTE DICHTUNG (in Laufmeter lieferbar)
Diese genarbte PVC-Dichtung wurde speziell für uns gestaltet und hergestellt. Sie wird in Laufmetern geliefert und dient hauptsächlich dazu, die oberen Nuten auf den Planken des Gepäckträgers zu schließen, um die Haftung auf der oberen Auflagefläche zu erhöhen. Die Dichtung kann auch zur Verbesserung der Optik montiert werden. Farbe schwarz.
63-A08787 WINKELPROFIL - ALUMINIUM (PAAR)
Winkelprofile aus Aluminiumguss, die seitlich die Last blockieren oder auch freitragend als Halterung eingesetzt werden können. In jeder Position verwendbar und mit den entsprechenden rechteckigen Muttern und Schrauben ausgestattet. Seitengröße 8,7 cm, Dicke 8,7 cm.
63-A04387 WINKELPROFIL - ALUMINIUM (PAAR) Seitengröße 8,7 cm, Dicke 4,3 cm.
63-A04343 WINKELPROFIL - ALUMINIUM (PAAR) Seitengröße 4,3 cm, Dicke 4,3 cm.
w w w. u p r a c k s . c o m 14
ZUBEHÖRTEILE
63-A019 UPRACKS ARBEITS- / CAMPINGTISCH
Dieser Tisch mit einer Tragfähigkeit von über 80 kg ist vollständig aus Aluminium (oben in Wabenstruktur) hergestellt. Die Tischfläche besteht aus einer Edelstahlfolie, die leicht zu reinigen ist. Im zusammengeklappten Zustand ist er 3,4 cm dick. Das Gewicht beträgt nur 10 kg. Größe: 144x69x h 70 cm. Der Befestigungssatz (63-A018) zum Klapptisch ist optional.
63-A018 BEFESTIGUNGSSATZ UPRACKS KLAPPTISCH )
Der Satz besteht aus zwei L-förmigen Haltern, die am Unterteil des Gepäckträgers befestigt werden. Der zusammengeklappte UPRACKS-Klapptisch läuft auf den dafür vorgesehenen Schienen und wird von zwei Feststellern blockiert.
63-A0191 UPRACKS CAMPING TISCH (bald kommend)
Dieser komplett faltbare Leichtgewichtstisch wurde entworfen, um mehr als 45kg Gewicht zu tragen. Gefaltet hat er nur noch 1/3 der Größe zum geöffneten Zustand. Rahmen komplett aus Aluminium. Oberfläche aus mehreren Schichten Holz mit Schutzbehandlung. Spezielle Scharniere und Beine. Eigengewicht 8 kg. Größe geöffnet: 110 x70x74 cm. (LxBxH) Größe geschlossen: 110x25x10cm (LxBxH). Zwei Befestigungs-Optionen um den Tisch auf dem Dachträger zu befestigen: 63-WT50SFK zur Montage auf der Oberseite des Dachträgers 63-A014 zur Montage an der Aussenseite des Dachträgers
63-AROL ROLLE
Rolle zum leichteren Beladen der Gepäckplattform. Größe: 680 mm. In verschiedenen Längen lieferbar (auf Anfrage).
63-A023 BEGEHBARE ALUPLATTEN
Wenn Sie eine robuste und vollbegehbare Teil- oder Vollfläche auf Ihrem Upracks Gepäckträger schaffen möchten, bieten die Aluplatten eine effektivste Lösung. Der Satz besteht aus 2 Aluminium-Riffelblech Modulen, welche in die Nuten der Planken des Trägers geschoben und mit abgerundeten Schrauben fixiert werden. Das System kann beliebig erweitert werden, so dass z.B. Laufwege oder auch größere Flächen entstehen. Es wurde so konzipiert, dass sogar Stühle darauf platziert werden und eine Aussichtsfläche, für Fotografen, Jäger und Naturliebhaber gebildet werden kann. Jede Platte ist ca. 50 cm lang und 19 cm breit.
63-WT50S WASSERTANK – 50 LITER – SCHMAL
Flacher Wassertank im Schnörkellosen, geradlinigem Design mit 50 Liter Kapazität. 1230 mm lang, 600 mm breit, nur 82 mm hoch.
63-WT50SFK WASSERTANK MOTAGEKIT Spezifischer Edelstahl-Montagekit für 63-WT50S.
63-WT20 20 LITER KANISTER
Plastik-Kanister für Wasser. Kapazität: 20 Liter. Größe: 350x170x470mm. Gewicht: 2,5 kg. Die Kanister passt auf 63-A005X.
63-A009 WINDABWEISER
Das zur Geräuschbeseitigung und zur Spritverbrauchssenkung entwickelte Leitblech kann in wenigen Minuten auf den UPRACKS-Gepäckträger geschraubt werden. Es ist möglich, das Blech entweder nach oben oder nach unten zu richten. Es können auch 2 Leitbleche eingebaut werden, um eine Luftdiffusion sowohl oben als auch unten zu erzeugen. Das Leitblech wird einzeln, samt Befestigungsmaterial geliefert.
63-A0091 ABS WINDABWEISER Breite: 120cm - passend für 1097cm breite Dachgepäckträger 63-A0092 ABS WINDABWEISER Breite: 112cm - passend für 1287cm breite Dachgepäckträger 63-A0093 ABS WINDABWEISER Breite: 132cm - passend für 1477cm breite Dachgepäckträger
63-AC45 ALUMINIUMKISTE
Exklusiv für UPRACKS gebaut, weist diese Aluminiumkiste einige besondere Eigenschaften auf: Blechdicke 1,2 mm; Deckeldichtung aus Gummi; Innenversiegelung zum Schutz des Inhalts gegen Witterungseinflüsse; Innenladevolumen 45 Liter. Abmessungen: 78,2x38,5 cm mit einer Höhe von nur 19 cm zur Senkung des aerodynamischen Widerstands. Gewicht: 4,2 kg.
BEFESTIGUNGSSATZ
63-FK001B FUSSSATZ REGENRINNE - Höhe von 12 > 16 cm. 63-FK002B FUSSSATZ REGENRINNE - Höhe von 16 > 20 cm. 63-FK003B FUSSSATZ REGENRINNE - Höhe von 20 > 26 cm. 63-FK004B FUSSSATZ REGENRINNE - Höhe von 26 > 31 cm.
Die Packung enthält ein Paar Füße (2) und wird mit dem notwendigen Material geliefert, um den Fuß mit dem Gepäckträger und der Regenrinne zu verbinden. Lieferumfang in jedem Satz: - 2 Füße gemäß Foto (das Foto zeigt nur einen Fuß samt Bauteilen) - 6 rechteckige Muttern mit den entsprechenden Schrauben zur Befestigung am Gepäckträger - 1 Magnet zum Abziehen der rechteckigen Muttern durch die dafür vorgesehenen Aussparungen - 2 pulverbeschichtete, im Kataphorese-Verfahren* behandelte Deckplatten mit Gummi-Pads - 2 Schraube mit Innensechskant zur Befestigung der Stahlabdeckung an der Regenrinne - 2 Platte mit Gewinde und 4 Schrauben zur Fußmontage. *Die selben Kits können auf Anfrage mit rostfreiem Material geliefert werden.
w w w. u p r a c k s . c o m 15
63-FEST INNERE VERLÄNGERUNG FÜR UPRACKS-FÜSSE - PAAR
Wenn der Fuß nicht nur auf dem einzelnen Querträger in Reihe montiert werden soll, kann dieser spezifische Adapter verwendet werden, mit dem es möglich ist, den Fuß in der Innenseite des Gepäckträgerrahmens zu befestigen. Gleichzeitig wird der Fuß auch am Außenrahmen verankert, um die Belastung gleichmäßiger auf dem Gepäckträger zu verteilen. Die zwei Fotos erläutern die Montage. Er wird paarweise mit den notwendigen Schrauben geliefert.
63-FKR ADAPTER FÜR FÜSSE RHINO RACK “C” - PAAR
Der Satz (2) dient zur Befestigung der bekannten Rhino-Rack Heavy Duty Regenrinnen-Füße an jedem UPRACKS-Gepäckträger. Enthalten sind 2 Adapter, 6 rechteckige Muttern, ein Magnet und Stahlbolzen. Es gibt verschiedene Gründe, warum die hochfesten Kunststofffüße von Rhino-Rack eingesetzt werden könnten. Dazu gehören: Gewichtsgründe, optische Gründe, oder wenn man bereits Rhino Rack Füße besitzt. Hinweis: Mit diesem besonderen C-förmigen Adapter ist es möglich, am UPRACKS-Gepäckträger auch andere Rhino Rack Heavy Duty Fußsätze zu montieren, welche auf vorgegebenen Montagepunkten oder mit speziellen Systemen auf dem Dach befestigt werden. Evtl. werden noch 63-FKRAIL benötigt. Fotos und spezifische Anwendungen finden Sie auf unserer Website.
63-FKRAIL ACHSABSTAND TRÄGER KIT - PAAR (kombiniert mit 63-FKR, wenn Rhino-Rack-Füße verwendet werden)
Der Adapter (2), ermöglicht, UPRACKS-Gepäckträger auf jedem Fahrzeug zu montieren und anzupassen. Wir haben diesen Adapter so gestaltet, dass die fahrzeugspezifischen Fußsätze von Rhino-Rack mit unserem Gepäckträger kombiniert werden können. Rhino-Rack bietet unzählige Montagesätze für Geländewagen, Pickups, SUVs, usw. an. Dieser Satz bildet eine Verbindungsbrücke zwischen zwei Querträgern (siehe Foto) und ermöglicht eine einfache Anpassung und Verbindung unseres UPRACKS-Gepäckträgers mit den Rhino-Füßen. Ein weiterer Vorteil dieses Systems liegt darin, dass ein breiterer oder längerer Gepäckträger als die Standard-Version ausgewählt und je nach Bedarf weiter nach vorne oder nach hinten positioniert werden kann. Der Adapter wird mittels unserer rechteckigen Bolzen befestigt und kann innerhalb der selektierten Querträger des Gepäckträgers verschoben werden. Hier sind zwei Beispiele zu sehen, wie wir die Adapter eingesetzt haben. Achtung: Wenn die Rhino-Rack-Füße verwendet werden, muss auch der dafür vorgesehene Adapter 63-FKR verbaut werden. Die Verpackung wird mit 2 Adaptern, 4 rechteckigen Muttern und entsprechenden Bolzen, sowie einem Magneten geliefert. Es reicht ein Adapter-Paar je Fuß-Paar.
16
SPECIAL KITS
w w w. u p r a c k s . c o m
63-FKJ15J12 MONTAGESATZ FÜR DEN TOYOTA PRADO 150/125
Alternativ zum RhinoRack Fußsatz bieten wir diesen äußerst robusten, speziell für den Toyota Prado J150/J120/J125 gefertigten, Montagesatz an. Die neue Bestellnummer dieses Montagesatzes lautet 63-FKJ15J12. Im Lieferumfang enthalten sind: 6x 63-FKRAIL (6 Paar Platten die zwischen die Querträger geschraubt werden); 3x 63-FK001 (3 Paar “Füße”); 6x fahrzeugspezifische Basiselemete. Dieser kit passt perfekt zu unseren UPRACKS Gepäckplattformen mit den Best.-Nr. 63-2112 / 63-2112P / 63-1712 / 63-1712P
63-FKJK2 MONTAGEKIT FÜR JEEP WRANGLER JK 2-TÜRIG (ohne Dachträger). 63-FKJK4 MONTAGEKIT FÜR JEEP WRANGLER JK 4-TÜRIG (ohne Dachträger).
Spezielles Design. Formschönes und sehr stabiles System mit 150 Kg Tragkraft. Die Montage erfolgt vollkommen ohne zu bohren. Durch diesen externen Überrollbügel können Sie den passenden Upracks Dachträger (siehe Anwendungliste auf Webseite) auf das Hardtop oder Softtop ihres Jeep Wrangler Unlimited ab Bj. ‘07 montieren. Einfach zu montieren, da der vordere Bügel auf dem Windschutzscheibenrahmen aufgesetzt wird. Der hintere Bügel ist mit speziellen C-Klemmen verschraubt und wird dann mittels eines speziellen Halters am Fahrzeugrahmen befestigt. Das Gewicht des kompletten Montagekit ist 37 Kg. Hergestellt aus Stahl, anschließend kataphoretisch- und schwarz pulverbeschichtet.
63-FKPANDA FUSSKIT FÜR NEUEN FIAT PANDA AB ‘12
Dieses stabile Fusskit-System passt in Kombination mit einen speziell entwickelten Upracks Dachgepäckträger. An der Original-Fahrzeug-Reling werden die fahrzeugspezifischen Füße an vier vormarkierten Punkten befestigt. Jede,an der Reling befestigte Klammer, wird zu einem starken festen Punkt, wo Sie den Dachträger verschrauben können. Der speziell entwickelte Upracks Dachgepäckträger, misst 1432,5 × 907 mm. Dieses System ermöglicht, den Dachgepäckträger, je nach Bedarf, weiter vorne zu plazieren. Die Tragfähigkeit des Gesamtsystems ist 70 Kg. Bitte beachten Sie die zulässige Dachlast des Herstellers.
Weil mehr Informationen und Details www.upracks.com besuchen
Š 2012. It is prohibited to reproduce, even partially, texts and images in this leaflet without prior written consent of 4Technique. Maggio 2014
17
www.upracks.it
w w w. u p r a c k s . c o m 18
MODELLI
La versione standard è verniciata a polvere in colore nero. É possibile avere anche la versione in alluminio naturale verniciato.
I portapacchi UPRACKS sono disegnati per assecondare al meglio qualsiasi esigenza di carico sul tetto. Le misure che troverai in seguito ti permettono qualsiasi tipo di applicazione su tutti i veicoli Fuoristrada, SUV e Crossover. Infatti, le misure disponibili, configurate in differenti lunghezze e larghezze, possono facilmente abbinarsi ad ogni tetto. Basterà verificare la superficie utile del proprio tetto e trovare nella tabella il giusto abbinamento dei nostri portapacchi UPRACKS. I portapacchi UPRACKS sono interamente in lega di alluminio che permette un alleggerimento enorme sul punto più alto del veicolo: il tetto. È molto importante ricordare che quando si pratica off-road (e non solo!) i materiali, attrezzature, accessori caricati devono essere ben disposti sia all’interno sia all’esterno del veicolo; è fondamentale cercare di tenere il peso elevato ad un baricentro il più basso possibile, mentre sul tetto bisogna contenere al massimo il carico per evitare pericolosi rollii. Un portapacchi in ferro o acciaio, ad esempio, risulta penalizzante a causa del peso che limita, già in origine, la portata di carico; con gli UPRACKS si ha un portapacchi dal peso molto contenuto a vantaggio di maggiore possibilità di carico. Nel libretto di manutenzione dei costruttori di veicoli, viene solitamente data indicazione specifica riguardo il carico massimo consentito ed è importante attenersi a tale informazione. Per quanto ci riguarda, noi di UPRACKS, siamo stati in grado di costruire portapacchi che vanno solo da 14 a 34 Kg di peso a seconda delle misure. Ecco un esempio: se un costruttore di veicoli indica una portata massima di 100 Kg vuole dire che il carico utile sarà dato al netto della tara del portapacchi, quindi se ho un portapacchi in alluminio che pesa solo 25 Kg significa poter caricare sul tetto ben 75 Kg di materiale; se avessi un portapacchi in ferro o acciaio il suo peso sarebbe almeno il triplo cioè 75 Kg, permettendo solo 25 Kg di portata utile! I portapacchi UPRACKS si fissano al tetto con appositi kit piedi e sono disponibili per veicoli con e senza grondaia; ci sono praticamente tutte le soluzioni per il perfetto montaggio. Fatta esclusione di quei veicoli che hanno sul tetto punti fissi di montaggio (dove forniamo l’apposito kit personalizzato), tutti gli altri veicoli possono montare i nostri kit piedi che sono offerti in quattro differenti altezze per abbinarsi perfettamente a tutti i tetti. I portapacchi UPRACKS possono essere fissati al tetto con soluzioni da 3 a 7 piedi per lato ed è per questo che le confezioni kit piedi vengono vendute a coppia in modo da dare massima libertà di scelta. I profili che formano cornice, supporto inferiore e piano calpestabile del portapacchi UPRACKS sono dotati di una speciale fessura che permette di fissare qualsiasi materiale ed accessorio tramite un apposito sistema chiamato “slide-in-all”; in questa fessura scorre un particolare dado rettangolare M8 che permette di imbullonare tutti gli accessori. I portapacchi UPRACKS, i kit piedi e gli accessori sono tutti trattati in cataforesi e successivamente verniciati a polvere di colore nero; tutta la bulloneria in dotazione è esclusivamente in acciaio e ferro zincato. A richiesta, possiamo fornire i portapacchi senza trattamento, quindi in alluminio naturale lucidato. CODICI, MISURE E FINITURE 63-1109 1079×907 mm 63-1109P 1079×907 mm 63-1409 1432,5×907 mm 63-1409P 1432,5×907 mm 63-1410 1432,5×1097 mm 63-1410P 1432,5×1097 mm 63-1412 1432,5×1287 mm 63-1412P 1432,5×1287 mm
alluminio nero alluminio lucidato alluminio nero alluminio lucidato alluminio nero alluminio lucidato alluminio nero alluminio lucidato
63-1710 1786×1097 mm 63-1710P 1786×1097 mm 63-1712 1786×1287 mm 63-1712P 1786×1287 mm 63-1714 1786×1477 mm 63-1714P 1786×1477 mm 63-1914 1950×1477 mm 63-1914P 1950×1477 mm
alluminio nero alluminio lucidato alluminio nero alluminio lucidato alluminio nero alluminio lucidato alluminio nero alluminio lucidato
63-2112 2139,5×1287 mm 63-2112P 2139,5×1287 mm 63-2114 2139,5×1477 mm 63-2114P 2139,5×1477 mm 63-2414 2493×1477 mm 63-2414P 2493×1477 mm 63-2814 2846,5×1477 mm 63-2814P 2846,5×1477 mm
alluminio nero alluminio lucidato alluminio nero alluminio lucidato alluminio nero alluminio lucidato alluminio nero alluminio lucidato
PROFILI
w w w. u p r a c k s . c o m 19
CORNICI SUPERIORI (TR) Per avere una cornice superiore già di misura, che segue perfettamente il profilo del proprio portapacchi, si può ordinare il set completo che ha già tutto l’occorrente. Il set completo denominato TR (Top Rail) è composto da: profilo frontale e posteriore, profili laterali, quattro profili curvati e supporti ad “S” (63-ASRFITS2) con relativi dadi inserto e bulloni. Molto facile da ordinare perché, se ad esempio abbiamo un portapacchi di 1,4 m di lunghezza x 1,0 di larghezza codice 63-1410 basterà ordinare la corrispondente cornice superiore con codice 63-1410TR. Il supporto 63-ASRFITS2 viene venduto anche separatamente in confezioni da due pezzi per chiunque desideri rinforzare ulteriormente il tutto. Per personalizzare maggiormente il proprio portapacchi UPRACKS con il top rail, grazie agli speciali supporti ad “S” si ottengono due differenti soluzioni di montaggio: soluzione 1 - tradizionale, che fissa la cornice superiore tenendola separata con una distanza di 45 mm dal portapacchi; soluzione 2 - la cornice viene imbullonata all’interno del supporto ad “S” creando una bordatura sul profilo del portapacchi. 63-1109TR COMPLETE TOP RAIL 1079×907 mm 63-1409TR COMPLETE TOP RAIL 1432,5×907 mm 63-1410TR COMPLETE TOP RAIL 1432,5×1097 mm 63-1412TR COMPLETE TOP RAIL 1432,5×1287 mm 63-1710TR COMPLETE TOP RAIL 1786×1097 mm 63-1712TR COMPLETE TOP RAIL 1786×1287 mm
alluminio nero alluminio nero alluminio nero alluminio nero alluminio nero alluminio nero
63-1714TR COMPLETE TOP RAIL 1786×1477 mm 63-1914TR COMPLETE TOP RAIL 1950×1477 mm 63-2112TR COMPLETE TOP RAIL 2139,5×1287 mm 63-2114TR COMPLETE TOP RAIL 2139,5×1477 mm 63-2414TR COMPLETE TOP RAIL 2493×1477 mm 63-2814TR COMPLETE TOP RAIL 2846,5×1477 mm
alluminio nero alluminio nero alluminio nero alluminio nero alluminio nero alluminio nero
45 mm
Soluzione 1.
Soluzione 2.
PROFILI CORNICE SUPERIORI - PARTI E ACCESSORI Per personalizzare il proprio portapacchi UPRACKS esiste la possibilità di montare una cornice superiore anche solo parziale. L’elenco sotto riportato indica le svariate possibilità per ottenere la configurazione più adatta alle proprie esigenze. Il disegno esploso indica i componenti per meglio comprendere ed acquistare la giusta configurazione. Tabella componenti 63-ASR100 63-ASR120 63-ASR150 63-ASR200 63-ASRQ 63-ASR75 63-ASR56 63-ASR37 63-ASRFITS2
PROFILO 3 CAVE - 1,00 m - coppia, neri PROFILO 3 CAVE - 1,20 m - coppia, neri PROFILO 3 CAVE - 1,50 m - coppia, neri PROFILO 3 CAVE - 2,00 m - coppia, neri CURVA CORNICE - coppia, neri PROFILO FRONTALE -75 cm - adatto per larg. 1477 cm, neri PROFILO FRONTALE -56 cm - adatto per larg. 1287 cm, neri PROFILO FRONTALE-37 cm - adatto per larg. 1097 cm, neri SUPPORTO / CONNETTORE CORNICE - coppia, nero
63-ASR100P 63-ASR120P 63-ASR150P 63-ASR200P 63-ASRQP 63-ASR75P 63-ASR56P 63-ASR37P 63-ASRFITS2
I profili frontali e le curve cornice sono disponibili verniciati a polvere in colore nero o in alluminio. Note: • Tutti i componenti possono essere ordinati in alluminio colore naturale o verniciati in nero. • I profili laterali da 100/120/150/200 cm sono venduti a coppia e l’imballo contiene: - n. 2 profili nella lunghezza stabilita - n. 4 tappi neri in nylon a finitura del terminale - n. 6 supporti /connettori ad “S” (63-ASRFITS2) - n. 24 dadi rettangolari con relativa bulloneria per il fissaggio al portapacchi • I profili frontali (o posteriori) sono tagliati a misura per adattarsi alle tre diverse larghezze dei portapacchi UPRACKS ed essere connessi ai profilati curvi. Vengono venduti singolarmente e l’imballo contiene: - n. 1 profilo nella lunghezza stabilita - n. 3 supporti /connettori ad “S” (63-ASRFITS2) - n. 12 dadi rettangolari con relativa bulloneria per il fissaggio al portapacchi
PROFILO 3 CAVE - 1,00 m - coppia, polished PROFILO 3 CAVE - 1,20 m - coppia, polished PROFILO 3 CAVE - 1,50 m - coppia, polished PROFILO 3 CAVE - 2,00 m - coppia, polished CURVA CORNICE coppia, polished PROFILO FRONTALE -75 cm -adatto per larg. 1477 cm, polished PROFILO FRONTALE -56 cm -adatto per larg. 1287 cm, polished PROFILO FRONTALE -37 cm -adatto per larg. 1097 cm, polished SUPPORTO / CONNETTORE CORNICE - coppia, nero
I profili sono disponibili verniciati a polvere in colore nero o in alluminio. •
i profili curvi (63-ASRQ), che fungono da angoli, sono sezionati a misura standard e sarà la scelta del profilo frontale a determinarne la larghezza finale per essere abbinato al proprio portapacchi UPRACKS. Vengono venduti a coppia e l’imballo contiene: - n. 2 cornici curve - n. 4 tappi neri a finitura del terminale - n. 4 supporti /connettori ad “S” (63-ASRFITS2) - n. 16 dadi rettangolari con relativa bulloneria per il fissaggio al portapacchi
w w w. u p r a c k s . c o m 20
ACCESSORI
63-A001 GOLFARO
Grazie alla misura standardizzata dei profili dei nostri portapacchi UPRACKS, questi anelli (tecnicamente “golfari”) si possono far scorrere in tutte le canaline e serrare con l’appositi bullone rettangolare 63-A002.
63-A00202 PIASTRINO ANCORAGGIO/DADO QUADRO/INSERTO - 20 mm, STANDARD 63-A002 PIASTRINO ANCORAGGIO/DADO RETTANGOLARE/INSERTO - 40 mm
Con il semplice scorrimento (sistema “slide-in-all”) questo speciale dado rettangolare (passo M8) permette di bloccare qualsiasi nostro accessorio; grazie alla sua forma può essere facilmente inserito nelle specifiche rotaie ed è appositamente disegnato per aumentare la tenuta a strappo.
63-A003 SCALA TELESCOPICA PORTATILE
Abbiamo pensato che la soluzione migliore per salire sul tetto consiste nell’avere una scala che poggia a terra. Una scelta dettata dalla necessità di avere maggior sicurezza nel salire e maggior flessibilità per poter accontentare tutti i possessori di veicoli che ovviamente hanno altezze da terra ben diverse. La scala telescopica una volta richiusa può facilmente essere legata sul portapacchi oppure stivata nel bagagliaio. Pesa solo 7 Kg ed arriva ad un’altezza di 260 cm. Non escludere di poterla utilizzare anche a casa.
63-ALRL SCALA POSTERIORE PER LAND ROVER DEFENDER
Utilizzando lo stesso profilo del portapacchi UPRACKS abbiamo ideato una semplice scaletta posteriore per il Land Rover Defender che va in appoggio sulla grondaia e viene imbullonata alla carrozzeria NEL LATO SINISTRO. É in alluminio verniciato a polvere nera con 3 pioli.
63-ALRLSET SCALA POSTERIORE PER LAND ROVER DEFENDER CON ESTENSIONE
Utilizzando la scaletta 63-ALRL come base di partenza, abbiamo aggiunto un’estensione scorrevole in verticale che permette di avere in tutto 6 pioli. L’estensione aggiunta scorre su appositi pattini in teflon e permette di avere ulteriori 60 cm di escursione verso il basso per una più agevole salita verso il tetto del veicolo. Una volta riposta e bloccata non interferisce con la targa del veicolo.
63-A004 PORTA RUOTA
Semplice e veloce da utilizzare, è stato realizzato in modo da non dover essere fissato in maniera permanente sul tetto. Una speciale piastra di forma a “C” asimmetrica, avvolge la barra trasversale del portapacchi. Una volta posizionata la ruota, il cono in resina va a centrarsi con il foro del cerchione ed il bullone a farfalla stringe a pacco l’asta andando a creare un bloccaggio a trazione. Questo sistema permette di posizionare, in piena sicurezza, prima la ruota sul portapacchi e solo successivamente ancorarla nella posizione più adatta alla propria esigenza sfruttando questo speciale aggancio. Il materiale metallico utilizzato per questo accessorio è acciaio Inox.
63-A005 PORTA TANICA SINGOLO MODULABILE
Questo porta tanica permette di posizionare sul portapacchi una singola tanica. Può essere montato sia longitudinalmente sia trasversalmente al fine di agevolare ed ottimizzare la spartizione dei pesi sul portapacchi. Il singolo kit porta tanica può essere abbinato ad altri tramite raccordo. In questo modo si possono ottenere multipli porta taniche perfettamente agganciati tra loro ed imbullonati al portapacchi. Specifici fori possono essere utilizzati per inserire lucchetto antifurto (non in dotazione).
63-A006 AGGANCIO UNIVERSALE A LEVA/GOMMA
Il kit è composto da una coppia di supporti in robusta gomma con laccetto di fissaggio che si possono montare tramite il dado rettangolare in qualsiasi posizione sfruttando le canaline (scasse) del portapacchi UPRACKS. 63-A0066 Ø da 15 mm a 34 mm 63-A0067 Ø da 25 mm a 63 mm 63-A0068 Ø da 44 mm a 73 mm 63-A0069 Ø da 69 mm a 88 mm
63-A007 PORTA BINDA x3
Un sistema semplice ed assolutamente resistente che fissa la binda Hi-Lift al portapacchi UPRACKS nel modo più sicuro e veloce. Il kit è composto da 3 supporti disegnati appositamente per permettere all’operatore di appoggiare la binda in massima sicurezza; solo successivamente, a binda appoggiata e con le mani libere, si procede all’ancoraggio. Al fine di sostenere il peso della binda (oltre 12 Kg) i 3 singoli supporti vengono corredati di ben 5 dadi e relativi bulloni in acciaio da fissare alla cornice del portapacchi UPRACKS. La binda viene bloccata al supporto con un perno a manopola.
63-A010 PORTA FANALI /ANTENNA
Coppia di supporti che possono essere fissati su qualsiasi punto della cornice perimetrale del portapacchi UPRACKS, sia verso il basso, sia verso l’alto. Utilizzabile anche come supporto universale e come porta antenna, si monta con 2 dadi rettangolari e relativi bulloni (compresi nel kit).
ACCESSORI
w w w. u p r a c k s . c o m 21
63-A011 PORTA VERANDA / SUPPORTO LUNGO
Kit composto da una coppia di supporti che si fissano alla cornice perimetrale del portapacchi UPRACKS. Si tratta di un supporto heavy duty in quanto si fissa con ben 5 dadi rettangolari e bulloni. Lo abbiamo chiamato porta veranda, ma risulta un eccellente supporto per appoggiare e fissare qualsiasi attrezzatura. Portata massima consigliata: 15 Kg, distribuiti sui 2 supporti.
63-A0111 SUPPORTO PER VERANDA
Il nuovo supporto per veranda è disegnato in due pezzi per consentire il fissaggio del tendalino/veranda all’interno o all’esterno del portapacchi Upracks, semplicemente facendolo slittare nella posizione desiderata. Per esempio, come mostrato nelle foto, se avete una cornice completa o avete caricato un grande volume sulla piattaforma del portapacchi e non avete più spazio a disposizione, con questo sistema, potete recuperare spazio, fissando il supporto più in alto e più esternamente al profilo del portapacchi. Questo supporto è stato disegnato per adattarsi a tutte le verande in commercio.
63-A012 COPPIA PIASTRE IN ALLUMINIO
Coppia di piastre da sabbia in alluminio verniciate di rosso. Misura 120 x 40 cm. Peso: 11,5 Kg.
63-TRAX1400 PIASTRA DA SABBIA
Per chi non desidera avere delle pesanti ed ingombranti piastre in metallo, questo accessorio in materiale plastico è estremamente duttile, leggero ed elastico. Un ottimo aiuto per tirarsi fuori dagli ostacoli ed economicamente conveniente. Misura: 1400x290x h30 mm. Peso: 2,5 Kg.
63-ASRFITS2 SUPPORTO / CONNETTORE
Supporto ad “S“ e relativa bulloneria per il montaggio. É utilizzato principalmente come supporto e raccordo della cornice superiore del portapacchi, ma può anche servire come ferma carico o sostegno di accessori. Realizzato in ferro, verniciato a polvere in colore nero. Venduto a coppia.
63-A014 PORTA PIASTRE
Costituito da una coppia di supporti che si fissano alla cornice del portapacchi con 4 dadi rettangolari e relativi bulloni. Ogni supporto ha in dotazione: 1 rondella, 1 cono in resina e 1 apposita chiave per stringere i dadi. Lo speciale cono in resina permette di adattare qualsiasi foro da un minimo di 30 mm ad un massimo di 120 mm. Chiave, dadi e kit fissaggio, tutto incluso nella confezione.
63-A015 CALAMITA PER PIASTRINO ANCORAGGIO/DADO RETTANGOLARE
Questa semplice micro calamita permette di estrarre agevolmente il dado rettangolare dalle canaline (scasse) del portapacchi UPRACKS.
63-A016 GUARNIZIONE SOTTILE ANTI FRUSCIO (vendita al metro)
Specificatamente disegnata e prodotta per noi, questa guarnizione in PVC viene fornita di serie in tre pezzi da 160 cm all’interno dell’imballo del portapacchi UPRACKS. Lo speciale design aiuta ad eliminare la possibile rumorosità. Permette di chiudere qualsiasi fessura (sopra, sotto, di lato ed al centro). Può semplicemente essere montata solo per dare un maggior garbo estetico. Colore nero.
63-A017 GUARNIZIONE LARGA ANTI SCIVOLO (vendita al metro)
Specificatamente disegnata e prodotta solo per noi, questa guarnizione zigrinata in PVC viene fornita al metro e serve principalmente per chiudere le fessure superiori del portapacchi al fine di avere maggior grip sulla parte superiore calpestabile. Se si desidera aumentare ulteriormente l’eleganza del portapacchi è possibile montare questa guarnizione anche nella fessura esterna della cornice del portapacchi stesso. Colore nero.
63-A08787 ANGOLARE ALLUMINIO (COPPIA)
Coppia di angolari in fusione di alluminio che permette di bloccare lateralmente il carico o posizionabile anche a sbalzo come supporto. Utilizzabili in qualsiasi posizione e corredati di relativi dadi rettangolari e bulloni. Misura 8,7 cm di lato, spessore 8,7 cm.
63-A04387 ANGOLARE ALLUMINIO (COPPIA) Misura 8,7 cm di lato, spessore 4,3 cm
63-A04343 ANGOLARE ALLUMINIO (COPPIA) Misura 4,3 cm di lato, spessore 4,3 cm.
w w w. u p r a c k s . c o m 22
ACCESSORI
63-A019 TAVOLO DA LAVORO / CAMPEGGIO UPRACKS
Realizzato per resistere ad oltre 80 Kg di portata, il tavolo è completamente in alluminio con una struttura a nido d’ape. Il piano è composto da una lamina di acciaio Inox che permette di essere facilmente pulita. Una volta ripiegato, il tavolo ha uno spessore di 3,4 cm. Il peso è di soli 11,5 Kg. Misura: 144x69x h 70 cm. Il kit fissaggio tavolino (63-A018) è un optional.
63-A018 KIT FISSAGGIO TAVOLINO UPRACKS (optional)
Il set è composto da due supporti ad L che si fissano sulla parte inferiore del portapacchi. In questo modo il tavolino UPRACKS, una volta ripiegato, scorre su queste specifiche rotaie e viene bloccato da due fermi appositamente realizzati.
63-A0191 UPRACKS DA LAVORO / CAMPEGGIO LIGHT (in produzione)
Realizzato per resistere ad oltre 45 Kg di portata, il tavolo è completamente pieghevole e da chiuso diventa 1/3 della dimensione originale. Struttura interamente in alluminio e top in legno multistrato trattato. Speciali cerniere e bracci. Chiuso, il tavolo è alto 10 cm. Il peso è di solo 8 Kg. Misure aperto: 110x70x h 73 cm. Misure chiuso: 110x25x h 10 cm. Fissabile al portapacchi in due differenti modi: 63-WT50SFK se lo volete posizionare sul portapacchi 63-A014 se lo volete posizionato sulla cornice esterna del portapacchi
63-AROL RULLO
Roller per agevolare il carico di accessori sul portapacchi. Misura: 680 mm. Disponibile in diverse lunghezze (su ordinazione).
63-A023 PIATTAFORMA CALPESTABILE
Se desideri creare una piattaforma solida, robusta e calpestabile che occupi totalmente o parzialmente la superficie del tuo portapacchi UPRACKS, questa è la soluzione più facile ed efficace. Il kit è composto da 2 pezzi di alluminio mandorlato, acquistabile in diversi multipli, e si fissa sulle feritoie superiori del portapacchi tramite bulloni con la testa arrotondata. Questo sistema è stato inventato per dare la possibilità di appoggiare delle seggiole da campeggio al fine di vivere la superficie del portapacchi come una terrazza. Ogni piastra è lunga 50 cm e larga 19 cm.
63-WT50S TANICA 50 LITRI MODELLO SLIM
Tanica per acqua, in versione “slim” (sottile), con capacità di 50 litri. Misure: 1230×600 mm e spessore di soli 8,2 mm.
63-WT50SFK KIT FISSAGGIO TANICA
Kit fissaggio specifico per tanica, interamente in acciao.
63-WT20 TANICA 20 LITRI
Tanica in plastica per acqua. Capacità: 20 litri. Misure: 350x170x470 mm. Peso Kg 2,5. Si fissa con il porta tanica 63-A005X.
63-A009 DEFLETTORE IN FERRO - UNIVERSALE
Disegnato per eliminare completamente il fruscio e ridurre i consumi, questo deflettore si monta sul portapacchi UPRACKS in pochi minuti utilizzando 3 punti di fissaggio. Può essere montato frontalmente, posteriormente con la possibilità di avere il flap rivolto verso l’alto o il basso. Si possono montare 2 deflettori creando una diffusione dell’aria sia sopra sia sotto. Larghezza 120 cm. Il deflettore viene venduto in confezione singola, comprensiva di bulloneria.
63-A0091 DEFLETTORE IN ABS Larghezza 120 cm - Adatto a portapacchi di larghezza 1097 cm 63-A0092 DEFLETTORE IN ABS Larghezza 112 cm - Adatto a portapacchi di larghezza 1287 cm 63-A0093 DEFLETTORE IN ABS Larghezza 132 cm - Adatto a portapacchi di larghezza 1477 cm
63-AC45 CASSA ALLUMINIO
Realizzata esclusivamente per UPRACKS, questa cassa in alluminio presenta alcune importanti caratteristiche: spessore lamiera 1,2 mm; guarnizione coperchio in gomma e sigillatura interna che permette di proteggere il contenuto dagli agenti atmosferici; volume di carico interno 45 litri. Misure: 78,2x38,5 cm con altezza di solo 19 cm al fine di ridurre l’impatto aerodinamico. Peso: 4,2 Kg.
KIT FISSAGGIO
63-FK001B COPPIA KIT PIEDE PER GRONDA altezza da 12 > 16 cm. 63-FK002B COPPIA KIT PIEDE PER GRONDA altezza da 16 > 20 cm. 63-FK003B COPPIA KIT PIEDE PER GRONDA altezza da 20 > 26 cm. 63-FK004B COPPIA KIT PIEDE PER GRONDA altezza da 26 > 31 cm. La confezione contiene una coppia di kit piedi e viene fornita con tutto il necessario per fissare in maniera definitiva ogni singolo piede al portapacchi. In dotazione ad ogni kit ci sono: - 2 piedi completi come da foto (la foto indica solo un piede ed i suoi componenti) - 6 dadi rettangolari con relativi bulloni in acciaio per il fissaggio al portapacchi - 1 calamita per estrarre i dadi rettangolari dalle apposite fessure - 2 cover fissaggio in ferro* trattato e verniciato a polvere con protezioni in gomma - 2 bulloni con testa a brugola per il fissaggio alla grondaia tramite cover in acciaio - 2 piastre filettate e 4 bulloni per assemblare il piede. *Gli stessi kit sono disponibili su richiesta con le cover fissaggio in acciaio INOX.
63-FKRAIL KIT PIASTRE INTERASSE BARRE - COPPIA (in abbinamento a 63-FKR se si usano piedi RHINO-RACK) Adattatore (confezione da 2 pezzi) che permette di poter montare ed adattare un portapacchi UPRACKS a qualsiasi tipo di veicolo utilizzando kit piedi in commercio. Abbiamo disegnato questo adattatore specialmente per abbinare gli specifici kit piedi della famosa Rhino-Rack al nostro portapacchi. Infatti Rhino-Rack offre un incredibile numero di kit montaggio per tutti quei veicoli Fuoristrada, SUV e Crossover che hanno punti di fissaggio sul tetto fissi e necessitano quindi di specifiche applicazioni. Questo kit è semplicemente composto da un ponte di collegamento tra una traversa e l’altra (vedi foto) permettendo così un facile adattamento e collegamento del nostro portapacchi UPRACKS ai piedi Rhino (o altri) e quindi al tetto. Ulteriore vantaggio di questo sistema consiste nella possibilità di scegliere un portapacchi più largo o più lungo dello standard ed inoltre poterlo posizionare più avanti o indietro in base alle proprie esigenze. L’adattatore infatti si fissa tramite i nostri bulloni rettangolari e si può fare scorrere all’interno della barra trasversale del portapacchi. Ecco alcuni esempi più eclatanti su e come abbiamo risolto questo problema. Attenzione: se si utilizzano piedini Rhino Rack è necessario acquistare l’apposito adattatore 63-FKR. La confezione viene fornita con 2 adattatori, 4 dadi rettangolari e relativi bulloni, calamita. La coppia di adattatori serve per una coppia di piedi.
w w w. u p r a c k s . c o m 23
63-FEST ESTENSIONE INTERNA PER PIEDI UPRACKS - COPPIA Se non si desidera montare il singolo piede sulla singola linea d’asse della traversa, abbiamo creato questo specifico adattatore che permette di fissare il piede all’interno della cornice del portapacchi. Le due foto spiegano il montaggio. Venduto a coppia con la bulloneria necessaria.
63-FKR ADATTATORE PER PIEDI RHINO RACK “C” - COPPIA Il kit viene fornito in confezione da 2 pezzi e serve per fissare i piedi classici da grondaia della famosa Rhino-Rack versione Heavy Duty a qualsiasi portapacchi UPRACKS. I piedi Rhino-Rack sono in materiale plastico e la scelta può essere dettata da motivi estetici, per ridotte necessità di carico o semplicemente perché già in possesso del kit Rhino ma con l’esigenza di montare un portapacchi diverso o in sostituzione di semplici barre da carico. Il kit 63-FKR viene fornito in imballo con 2 adattatori, 6 dadi rettangolari, una calamita e bulloneria in acciaio. Nota: questo particolare adattatore a “C” permette di fissare al portapacchi UPRACKS anche il kit piedi Heavy Duty della Rhino-Rack disegnati per ogni singolo veicolo che ha punti fissi di ancoraggio al tetto e non ha grondaie. Verifica periodicamente il nostro sito per vedere le fotografie e le specifiche applicazioni.
24
SPECIAL KITS
63-FKJ15J12 KIT PER TOYOTA PRADO 150/125
Si tratta di un’alternativa heavy duty per chi volesse installare il portapacchi UPRACKS su Toyota J150/J120/J125 senza utilizzare i fissaggi della Rhino-Rack ed è adatto per montare portapacchi 63-2112 63-2112P 63-1712 63-1712P. Il kit è composto da: 6 x 63-FKRAIL (totale 12 piastre interasse); 3 x 63-FK001 (senza base); 6 x adattatori tetto.
w w w. u p r a c k s . c o m
63-FKJK2 COMBO FITTING KIT PER WRANGLER JK 2 PORTE (portapacchi escluso). 63-FKJK4 COMBO FITTING KIT PER WRANGLER JK 4 PORTE (portapacchi escluso).
Dallo speciale design piacevole alla vista, è soprattutto un sistema heavy duty per caricare oltre 150 Kg, senza bisogno di forare la carrozzeria. Questa struttura tubolare permette di montare il portapacchi Upracks (guarda sul web la guida alle applicazioni) sui modelli di Jeep Wrangler Unlimited dal 2007 in avanti, con hard top o soft top. Di facile installazione, grazie all’attacco del roll-bar sulla piastra frontale posizionata ai fianchi del parabrezza. Il tubolare posteriore viene invece fissato con speciali morsetti a “C” e poi montato su una piastra rinforzata direttamente imbullonata al telaio. Una volta montato questo sistema di roll-bars, può essere utilizzato sul veicolo già così oppure è possibile comprare a parte il nostro portapacchi Upracks nella misura che più vi aggrada. Il peso complessivo di questo kit tubolare è di 37 Kg. Interamente in tubolare di ferro trattato in cataforesi e verniciato a polvere epossidica in colore nero.
63-FKPANDA COPPIA DI PIEDI PER LA NUOVA FIAT PANDA 2012
Questo sistema heavy duty è specificatamente disegnato per la perfetta combinazione del portapacchi Upracks. Sulle barre originali del veicolo, questo kit si fissa in corrispondenza dei quattro punti segnati. Ciascun piede, una volta fissato sulle barre, diventa un unico resistente punto di fissaggio sul quale montare il portapacchi. Il portapacchi Upracks specifico per questo veicolo è il 63-1409 che misura 1432,5×907 mm. Con questo sistema è possibile scorrere il portabagagli più avanti o più indietro secondo le proprie necessità. La capacità di carico totale del sistema completo è di oltre 70 Kg ma si consiglia di seguire le indicazioni della casa costruttrice del veicolo che indica un carico di 60 Kg al massimo.
Per maggiori informazioni e dettagli visita il sito www.upracks.com
© 2012. Il est interdit de reproduire, même partiellement, les textes et les images de ce dossier sans autorisation écrite préalable de la part de Outback Import. May 2014
25
www.upracks.fr
w w w. u p r a c k s . c o m 26
MODELS
La version standard est noir (peinture polyuréthane). Disponible également en version aluminium
Les systèmes de GALERIES UPRACKS ont été spécialement développés pour mieux répondre aux besoins spécifiques des 4X4 et SUV. 8 modules, aux dimensions bien définies, permettent tous types d’application sur tous les véhicules tout-terrain, SUV et multi-segments. Ces 8 modules, disponibles en différentes longueurs et largeurs, peuvent facilement s’adapter sur n’importe quel toit. Le tableau d’application permet de définir facilement la bonne solution UPRACKS à partir des dimensions de votre toit. Les GALERIES UPRACKS sont réalisés intégralement en alliage d’aluminium, ce qui permet d’alléger énormément le point le plus élevé du véhicule : le toit. Ce point est crucial : on ne rappellera jamais assez l’importance de la position du centre de gravité dans la pratique du tout-terrain (et pas seulement !). Il faut donc positionner soigneusement les équipements et les accessoires de votre véhicule, aussi bien à l’intérieur qu’à l’extérieur. Et plus on monte, plus le poids est critique ! Une galerie en aluminium, généreusement dimensionné, reste bien plus légère qu’en acier. Votre capacité de chargement se trouve augmentée d’autant ! Dans la notice, les constructeurs de véhicules indiquent le chargement maximum autorisé et il est important de se tenir à cette recommandation. UPRACKS ne pèse que de 14 à 34 Kg, suivant les dimensions, ce qui vous donne une beaucoup plus grande capacité de chargement. Par exemple : Si le constructeur de votre véhicule indique une portée maximum de 100 Kg, cette valeur inclut la galerie ! Donc pour déterminer le chargement utile réel, il faut retirer le poids de la galerie. Ainsi, avec une galerie en aluminium de seulement 25 Kg, cela signifie qu’il est possible de charger sur le toit jusqu’à 75 Kg; si la galerie était en acier, elle pèserait au moins trois fois plus, soit 75 Kg, permettant de charger seulement 25 Kg! Les GALERIES UPRACKS sont fixées sur le toit avec des kits de pieds spécifiques adaptés à chaque véhicule, avec ou sans gouttière. Pour les véhicules à points fixes de montage, nous fournissons le kit approprié et personnalisé ; Pour les autres véhicules, nous proposons des kits de pieds en trois différentes hauteurs pour s’adapter parfaitement à tous les toits. Pour permettre une totale liberté, les pieds sont vendus par paires, cela vous permet de choisir le nombre de pieds : de 3 et à 7 paires. Les profils formant le cadre, le support inférieur et la surface utilisable des GALERIES UPRACKS, sont équipés d’un rail spécialement étudié, qui permet de fixer tous matériels et tous accessoires par un système spécifique “slide-in-all”. Un écrou spécial rectangulaire peut coulisser dans ce rail et permet la fixation des tous les accessoires à l’emplacement souhaité. Les GALERIE UPRACKS, les kits de pieds et les accessoires sont tous traités par cataphorèse puis par peinture polyuréthane noire; tous les boulons sont en acier. Les galerie sont disponibles sans traitement, c’est-à-dire en aluminium naturel brossé, sur simple demande. CODES, MESURES ET FINITIONS 63-1109 1079×907 mm 63-1109P 1079×907 mm 63-1409 1432,5×907 mm 63-1409P 1432,5×907 mm 63-1410 1432,5×1097 mm 63-1410P 1432,5×1097 mm 63-1412 1432,5×1287 mm 63-1412P 1432,5×1287 mm
aluminium noir aluminium poli aluminium noir aluminium poli aluminium noir aluminium poli aluminium noir aluminium poli
63-1710 1786×1097 mm 63-1710P 1786×1097 mm 63-1712 1786×1287 mm 63-1712P 1786×1287 mm 63-1714 1786×1477 mm 63-1714P 1786×1477 mm 63-1914 1950×1477 mm 63-1914P 1950×1477 mm
aluminium noir aluminium poli aluminium noir aluminium poli aluminium noir aluminium poli aluminium noir aluminium poli
63-2112 2139,5×1287 mm 63-2112P 2139,5×1287 mm 63-2114 2139,5×1477 mm 63-2114P 2139,5×1477 mm 63-2414 2493×1477 mm 63-2414P 2493×1477 mm 63-2814 2846,5×1477 mm 63-2814P 2846,5×1477 mm
aluminium noir aluminium poli aluminium noir aluminium poli aluminium noir aluminium poli aluminium noir aluminium poli
REBORDS
w w w. u p r a c k s . c o m 27
CADRES SUPÉRIEURS (TR) Il est possible de commander un kit complet fournit de tout le nécessaire pour obtenir un cadre supérieur d’une taille qui suit parfaitement le profil du porte-bagages. TR (Top Rail) est le kit complet qui fournit: un profil avant et arrière, profils latéraux, quatre cornières d’angle et douze supports en “S” (63-ASRFITS2) équipés d’écrous et boulons. Très facile à commander : par exemple pour des porte-bagages de 1,4 m de longueur x 1,0 m de largeur code 63-1410 il suffira de commander un cadre supérieur ayant le code 63-1410TR pour le porte-bagages UPRACKS correspondant. Le support 63-ASRFITS2 est vendu séparément en emballages de deux pour tous ceux qui désirent renforcer tout l’ensemble. Mais ce n’est pas tout ! Il est possible de personnaliser davantage son propre porte-bagages UPRACKS en utilisant le Top Rail grâce aux supports en “S” spéciaux et selon deux différentes solutions de fixation : solution 1 – traditionnel qui fixe le cadre supérieur séparé à 45 mm de distance du porte-bagages (voir photo) ; solution 2 – le cadre est fixé par des boulons à l’intérieur du support en “S” et crée une bordure à l’extérieur du porte-bagages. Prouvez-le ! 63-1109TR COMPLETE TOP RAIL 1079×907 mm 63-1409TR COMPLETE TOP RAIL 1432,5×907 mm 63-1410TR COMPLETE TOP RAIL 1432,5×1097 mm 63-1412TR COMPLETE TOP RAIL 1432,5×1287 mm 63-1710TR COMPLETE TOP RAIL 1786×1097 mm 63-1712TR COMPLETE TOP RAIL 1786×1287 mm
aluminium noir aluminium noir aluminium noir aluminium noir aluminium noir aluminium noir
63-1714TR COMPLETE TOP RAIL 1786×1477 mm 63-1914TR COMPLETE TOP RAIL 1950×1477 mm 63-2112TR COMPLETE TOP RAIL 2139,5×1287 mm 63-2114TR COMPLETE TOP RAIL 2139,5×1477 mm 63-2414TR COMPLETE TOP RAIL 2493×1477 mm 63-2814TR COMPLETE TOP RAIL 2846,5×1477 mm
aluminium noir aluminium noir aluminium noir aluminium noir aluminium noir aluminium noir
45 mm
Solution 1.
Solution 2.
REBORDS Pour personnaliser votre GALERIE UPRACKS, il est possible de monter un cadre supérieur, des rebords, complets ou partiels. Vous trouverez ci-dessous les éléments qui vous permettent de réaliser votre configuration : Le plan éclaté joint permet une meilleure visualisation des composants et des configurations possibles. Tableau composants 63-ASR100 63-ASR120 63-ASR150 63-ASR200 63-ASRQ 63-ASR75 63-ASR56 63-ASR37 63-ASRFITS2
PAIRE REBORDS LATERAUX - 1,00 m - noir PAIRE REBORDS LATERAUX - 1,20 m - noir PAIRE REBORDS LATERAUX - 1,50 m - noir PAIRE REBORDS LATERAUX - 2,00 m - noir PAIRE D’ANGLES - noir REBORD FRONTAL -75 cm - pour galerie largeur 1477 cm, noir REBORD FRONTAL -56 cm - pour galerie largeur 1287 cm, noir REBORD FRONTAL -37 cm - pour galerie largeur 1097 cm, noir PAIRE SUPPORTS/RACCORDS POUR LES REBORDS - noir
63-ASR100P 63-ASR120P 63-ASR150P 63-ASR200P 63-ASRQP 63-ASR75P 63-ASR56P 63-ASR37P 63-ASRFITS2
PAIRE REBORDS LATERAUX - 1,00 m - poli PAIRE REBORDS LATERAUX - 1,20 m - poli PAIRE REBORDS LATERAUX - 1,50 m - poli PAIRE REBORDS LATERAUX - 2,00 m - poli PAIRE D’ANGLES - poli REBORD FRONTAL -75 cm - pour galerie largeur 1477 cm, poli REBORD FRONTAL -56 cm - pour galerie largeur 1287 cm, poli REBORD FRONTAL -37 cm - pour galerie largeur 1097 cm, poli PAIRE SUPPORTS/RACCORDS POUR LES REBORDS - noir
Les profils avant et les cornières d’angles sont disponibles avec peinture noire polyurethane ou en aluminium brossé. Remarques : • Tous les composants peuvent être commandés en aluminium naturel ou peints en noir. • Les profils latéraux de 100/120/150/200 cm sont vendus par paire et l’emballage contient : - n. 2 profils à dimension. - n. 4 bouchons noirs en nylon de finition d’extrémité - n. 6 supports/raccords (63-ASRFITS2) - n. 24 écrous rectangulaires avec leurs boulons en acier pour fixer le tout à la GALERIE • Les profils avant (ou arrière) sont découpés sur mesure pour s’adapter aux trois différentes largeurs des GALERIES UPRACKS et pour les attacher aux profils courbés. Vendus individuellement, l’emballage contient : - n. 1 profil à dimension. - n. 3 supports/raccords (63-ASRFITS2) - n. 12 écrous rectangulaires avec leurs boulons en acier pour fixer le tout à la GALERIE
•
Les profils courbés (63-ASRQ), qui servent de cornières d’angles, sont livrés par segments de dimension standard. Ils doivent être choisis en fonction du profil avant pour être assorti à la GALERIE UPRACKS que vous avez choisi. Vendus individuellement, l’emballage contient : - n. 2 cornières d’angles - n. 4 bouchons noirs de finition d’extrémité - n. 4 supports/raccords INOX (63-ASRFITS2) - n. 12 écrous rectangulaires avec leurs boulons en acier pour fixer le tout à la GALERIE
w w w. u p r a c k s . c o m 28
ACCESSOIRES
63-A001 OEILLETS D’ARIMAGE
Grâce aux dimensions standards des profils des GALERIES UPRACKS, ces œillets d’arrimage peuvent glisser dans tous les rails UPRACK et être serrées en utilisant le boulon rectangulaire 63-A002.
63-A00202 PLAQUE D’ANCRAGE/ECROU CARRÉ - 20 mm, STANDARD 63-A002 PLAQUE D’ANCRAGE/ECROU RECTANGULAIRE - 40 mm
Grâce au simple système de rail (système “slide-in all”), cet écrou rectangulaire spécial (pas M8) permet de bloquer tous nos accessoires; Il peut être facilement inséré dans les rails. Sa grande surface d’appui permet une très grande résistance aux chocs.
63-A003 ÉCHELLE PLIANTE
Nous avons pensé que la meilleure solution pour monter sur le toit était une échelle reposant sur le sol. Conçue pour garantir une sécurité optimale de montage et plus de flexibilité pour satisfaire tous ceux qui ont des véhicules ayant évidemment des hauteurs bien différentes. L’échelle pliante, une fois repliée, peut être facilement attachée à la GALERIE, ou bien rangée dans le coffre. Elle pèse seulement 7 Kg et mesure 260 cm. Vous pouvez l’utiliser même à la maison.
63-ALRL ECHELLE ARRIÈRE POUR LAND ROVER DEFENDER
Sur la base des mêmes cadres de galeries UPRACKS, nous avons conçu une échelle d’alliage simple qui s’adapte sur l’arrière, côté gauche, du DEFENDER. ecouverte d’une peinture epoxy noire cuite au four, cette échelle peut être verrouillée sur le véhicule comme visible sur images.
63-ALRLSET ECHELLE ARRIÈRE POUR LAND ROVER DEFENDER AVEC EXTENSION
En utilisant comme base l’échelle 63-ALRL, nous pouvons ajouter une extension, grâce à trois barreaux supplémentaires, ce qui permet de la faire glisser de plus de 60 cm vers le bas. Lorsque cette extension est fermée sur sa base, aucune interférence avec le chassis du véhicule.
63-A004 PORTE-ROUE
Simple et rapide à utiliser, il a été réalisé pour ne pas à avoir besoin de le fixer de manière permanente sur le toit. Une plaque spéciale en “C” asymétrique enveloppe la barre transversale de la GALERIE. Une fois la roue placée, le cône en résine est centré dans le trou de la jante et l’œillet d’arrimage serre à fond la tige en créant ainsi un blocage par traction. Ce système permet de placer, en toute sécurité, la roue sur la GALERIE d’abord, et de l’accrocher, ensuite, dans la position la plus appropriée selon vos besoins, en utilisant cet accrochage spécial. Cet accessoire est en acier inox.
63-A005 PORTE-JERRICAN INDIVIDUEL MODULABLE
Ce porte-jerrican permet de placer sur la GALERIE un seul jerrican. Il peut être monté longitudinalement aussi bien que transversalement pour faciliter et optimiser la répartition des poids sur la GALERIE. Il est possible d’assortir le kit porte-jerrican à d’autres accessoires à l’aide d’un raccord. On peut ainsi avoir des porte-jerrican multiples parfaitement accrochés entre eux et boulonnés à la GALERIE. Il est possible d’utiliser des trous spécifiques pour ajouter un cadenas antivol (non fournis dans ce kit)
63-A006 KIT D’ACCROCHAGE UNIVERSEL A LEVIER/CAOUTCHOUC
Le kit se compose d’une paire de supports galvanisés qui peuvent être montés dans toutes positions à l’aide de l’écrou rectangulaire, en utilisant les rainures (chanfreinées) des GALERIES UPRACKS. Fixé par un lacet en caoutchouc épais. 63-A0066 Ø de 15 mm à 34 mm 63-A0067 Ø de 25 mm à 63 mm 63-A0068 Ø de 44 mm à 73 mm 63-A0069 Ø de 69 mm à 88 mm
63-A007 PORTE -CRIC x3
Un système simple et très résistant qui fixe le cric Hi-Lift à la GALERIE UPRACKS dans la manière la plus sûre et la plus rapide. Le kit se compose de 3 supports conçus spécialement pour permettre à l’opérateur d’appuyer le cric en toute sécurité; Il est possible de l’accrocher seulement après avoir appuyé le cric et en ayant les mains libres. Pour supporter le poids du cric (plus de 12 Kg), chacun des 3 supports est équipé de 5 écrous avec leurs boulons en acier pour les fixer au cadre de la GALERIE UPRACKS. Le cric est bloqué sur le support par une vis à poignée.
63-A010 PORTE-PHARES/ANTENNE
Le kit se compose d’une paire de supports qui peuvent être fixés sur n’importe quel point du cadre de la GALERIEUPRACKS, vers le bas, ou vers le haut. Il peut être utilisé en tant que support universel aussi bien que comme porte antenne. Il se monte à l’aide de 2 écrous rectangulaires avec leurs boulons (inclus dans le kit).
ACCESSOIRES
w w w. u p r a c k s . c o m 29
63-A011 PORTE-AUVENT / SUPPORT LONG
Le kit se compose d’une paire de supports qui peuvent être fixés au cadre de la GALERIE UPRACKS. Il s’agit d’un support très résistant à fixer par 5 écrous rectangulaires avec leurs boulons. Nous l’avons appelé “porte-auvent”, mais il s’agit d’un excellent support pour porter et fixer tous types d’équipement. Portée max. conseillée : 15 Kg répartis sur les 2 supports.
63-A0111 SUPPORT POUR VÉRANDA
Le nouveau support pour véranda est conçu en deux pièces pour permettre le montage du tendelet /véranda à l’intérieur ou à l’extérieur du porte-bagages Upracks : il faut simplement le coulisser dans la position souhaitée. Comme montré dans les photos, si vous avez un cadre complet ou vous avez chargé un grand volume sur la plateforme du porte-bagages et il ne vous reste plus d’espace, il est possible par ce système de récupérer de l’espace si vous fixez le support plus en haut et plus à l’extérieur du profil du porte-bagages. Ce support a été conçu pour s’adapter à toute véranda présente sur le marché.
63-A012 PAIRE DE PLAQUES EN ALUMINIUM
Paire de plaques à sable en aluminium peintes en rouge. Dimensions 120 x 40 cm. Poids : 11,5 Kg.
63-TRAX1400 PLAQUE A SABLE
Plaque à sable en plastique. Extrêmement flexible, légère et élastique. Très bonne alternative aux plaques en métal lourdes et volumineuses. Peut aider à franchir un obstacle. Prix très compétitif. Dimensions : 1400X290X30 mm (hauteur). Poids : 2.5 Kgs
63-ASRFITS2 SUPPORT / RACCORD
Support en “S” et les boulons en dotation pour le montage. Il est utilisé principalement en tant que support et raccord du cadre supérieur du porte-bagages, mais il peut être aussi utilisé pour bloquer le chargement ou en tant que support d’accessoires. Il est fourni en fer, peint à poudre en noir.
63-A014 PORTE-PLAQUES
Il s’agit d’une paire de supports à fixer au cadre de la GALERIE avec 5 écrous et leurs boulons. Chaque support est pourvu de : 1 rondelle, 1 cône en résine et 1 clé spéciale pour serrer les écrous. Le cône spécial en résine permet d’adapter toute plaque ayant des orifices compris entre 30 mm et 120mm. Clé, écrous et kit de fixation inclus dans l’emballage.
63-A015 AIMANT POUR PLAQUE D’ANCRAGE/ECROU RECTANGULAIRE
Ce simple micro-aimant permet de sortir aisément l’écrou rectangulaire des rails de la GALERIE UPRACKS.
63-A016 JOINT FIN ANTI-SIFFLEMENT (vendu au mètre) Ce joint en PVC, spécialement conçu et produit pour UPRACKS, est fourni de série en trois sections de 160 cm à l’intérieur de l’emballage de la GALERIE UPRACKS. Son design spécial permet d’éliminer tout sifflement. Il permet de combler tout interstice (en haut, en bas, de côté et au centre). Il apporte également un effet esthétique. Couleur : noir. 63-A017 JOINT LARGE ANTI-DERAPANT (vendu au mètre) Ce joint en PVC favorisant l’adhérence, spécialement conçu et produit pour UPRACK, est fourni de série au mètre et sert surtout pour combler les interstices supérieurs de la GALERIE et avoir plus d’adhérence sur la surface supérieure. Il est possible de le monter même à l’extérieur du cadre pour donner un meilleur aspect. Couleur : noir. 63-A08787 KIT DE FIXATION EN ALUMINIUM (PAIRE)
Paire de fixation en alliage d’aluminium qui permettent de bloquer sur le côté le chargement. Elles peuvent également être placées en saillie en tant que support. Utilisables dans toutes positions et pourvues de leurs écrous rectangulaires et boulons. Dimensions : 8,7 cm de côté, 8.7 cm d’épaisseur.
63-A04387 KIT DE FIXATION EN ALUMINIUM (PAIRE) Dimensions : 8,7 cm de côté, 4.3 cm d’épaisseur
63-A04343 KIT DE FIXATION EN ALUMINIUM (PAIRE) Dimensions : 4.3 cm de côté, 4,3 cm d’épaisseur
w w w. u p r a c k s . c o m 30
ACCESSOIRES
63-A019 TABLE DE TRAVAIL / CAMPING UPRACKS
Réalisée pour supporter jusqu’à 80 Kg et plus, la structure de la table est en aluminium en nid d’abeilles. La surface est en acier inox pour être facilement nettoyée. Une fois repliée, la table a une épaisseur de 3.4 cm. Elle pèse seulement 10 Kg. Dimensions : 144x69x h 70 cm. Le kit de fixation de la table (63-A018) est en option. 63-A018 KIT FIXATION TABLE UPRACKS (option) Le kit se compose de deux supports en “L” qui sont à fixer sur la partie inférieure de la GALERIE. De cette manière, la table UPRACKS, une fois repliée, glisse sur ces rails spéciaux et est bloquée par deux arrêts.
63-A0191 UPRACKS TABLE DE CAMPING LEGERE (venant bientôt)
Conçue pour supporter plus de 45 kilos, cette table est complètement pliable pour faire 1/3 de sa taille ouverte. Cadre en aluminium. Dessus de table en bois traité multicouches. Charnières et pieds spéciaux. Chiuso, il tavolo è alto 10 cm. Elle pèse seulement 8 Kg. Dimensions: 110x70x h 73 cm - 110x25x h 10 cm.
63-AROL ROULEAU
Rouleau pour faciliter le chargement des accessoires sur la GALERIE. Dimensions : 680 mm. Disponible en différentes longueurs (sur commande).
63-A023 PLATEFORME EN ALUMINIUM
Voilà la solution la plus facile et efficace si vous désirez créer une plateforme assez solide et robuste pour y marcher dessus et qui occupe entièrement ou partiellement la surface de votre porte-bagages UPRACKS. Un kit composé de 2 pièces en aluminium en forme d’amande qui peut être acheté en plusieurs unités. Il se fixe dans les fentes supérieures du porte-bagages au moyen de boulons à tête ronde. Il est possible par ce système de construire et personnaliser une plateforme solide qui peut s’étendre sur la surface entière ou partiellement sur certains points du porte-bagages où il est nécessaire d’avoir une partie sur laquelle on peut marcher. Ce système a été conçu pour offrir la possibilité d’appuyer des chaises de camping pour pouvoir utiliser la surface du porte-bagages comme une terrasse. Chaque plaque mesure 50 cm de longueur et 19 cm de largeur.
63-WT50S JERRICAN DE 50 LITRES MODÈLE SLIM
Jerrican pour eau, en version “slim” (étroit), capacité de 50 litres. Mesures : 1230×600 mm et épaisseur de 8,2 mm seulement.
63-WT50SFK KIT DE FIXATION JERRICAN Kit de fixation spécifique pour jerrican (63-WT50S), entièrement en acier inox. 63-WT20 JERRICAN DE 20 LITRES
Jerrycan de plastique. Capacité : 20 lt. Mesures : 350x170x470 mm. Poids : Kg 2,5. Le Jerrycan va sur 63-A005X.
63-A009 CARÉNAGE UNIVERSEL EN FER
Il a été conçu pour arrêter le bruit du vent et réduire la consommation d ‘essence. Ce carénage peut être installé sur les galeries de toit Upracks seulement en quelques minutes en utilisant 3 points d’attache. Il peut être fixé à l’avant ou à l’arrière du véhicule et le volet peut être positionné vers le haut ou vers le bas. 2 carénages peuvent être fixés diffusant alors l’air vers le haut et vers le bas. Le carénage est vendu comme pièce unitaire dans un pack comprenant vis et boulons.
63-A0091 CARENAGE ABS Largeur 120 cm – Conçu pour galerie de toit de largeur 1097 cm 63-A0092 CARENAGE ABS Largeur 112 cm – Conçu pour galerie de toit de largeur 1287 cm 63-A0093 CARENAGE ABS Largeur 132 cm – Conçu pour galerie de toit de largeur 1477 c
63-AC45 CAISSE EN ALUMINIUM
Cette caisse en aluminium, réalisée en exclusivité pour UPRACKS, a des caractéristiques intéressantes : épaisseur de tôle 1,2 mm, joint en caoutchouc pour le couvercle et étanchéité interne qui permet de protéger le contenu des agents atmosphériques. Volume de chargement interne 45 litres. Dimensions : 78,2x38,5 cm avec une hauteur réduite de 19 cm pour réduire l’impact aérodynamique. Poids : 4,2 Kg.
KIT DE FIXATION
63-FK001B KIT PAIRE DE PIEDS hauteur de 12 > 16 cm. 63-FK002B KIT PAIRE DE PIEDS hauteur de 16 > 20 cm. 63-FK003B KIT PAIRE DE PIEDS hauteur de 20 > 26 cm. 63-FK004B KIT PAIRE DE PIEDS hauteur de 26 > 31 cm. L’emballage contient une paire de kits de pieds complets pour fixer de manière définitive chaque pied à la GALERIE Chaque kit contient : - 2 pieds complets comme sur la photo (sur la photo il y a un seul pied et ses composants) - 6 écrous rectangulaires avec leurs boulons en acier pour fixer le tout à la GALERIE - 1 aimant pour extraire les écrous rectangulaires de leurs trous - 1 couverture de fixation en fer* avec protections en caoutchouc - 1 boulon à tête hexagonale pour fixation à la gouttière à travers la couverture en acier - plaque filetée et 2 boulons pour assembler le pied. *Ou en acier.
w w w. u p r a c k s . c o m 31
63-FEST PAIRE EXTENSION INTERNE POUR PIEDS UPRACKS Si vous ne voulez pas monter chaque pied dans chaque axe de la barre transversale, nous avons créé cet adaptateur spécifique qui permet de fixer le pied à l’intérieur du cadre de la GALERIE. Les deux photos montrent le montage. Vendu par paire avec les boulons nécessaires.
63-FKR ADAPTATEUR POUR PIEDS RHINO RACK “C” - PAIRE Le kit sert à adapter les pieds pour gouttière Rhino-Rack version Heavy Duty à tous types de GALERIE UPRACKS. Le kit 63-FKR est fourni en emballage avec 2 adaptateurs, 6 écrous rectangulaires, un aimant et des boulons en acier. Remarque : cet adaptateur en “C” permet de fixer à la GALERIE UPRACKS les pieds Heavy Duty de Rhino-Rack, conçus pour tout véhicule ayant des points de montage fixes sur son toit et sans gouttières. 63-FKRAIL KIT PLAQUES ENTRAXES BARRES - PAIRE (en association avec 63-FKR pour les pieds Rhino-Rack) Adaptateur (emballage de 2 pièces) qui permet de monter et adapter une GALERIE UPRACKS à tous types de véhicules en utilisant les kits de pieds du marché. Nous avons conçu cet adaptateur spécialement pour associer les kits spécifiques RhinoRack à notre GALERIE UPRACKS. En effet, Rhino-Rack offre une quantité incroyable de kits de montage pour tous les véhicules tout-terrain, SUV et multi-segments qui ont des points de montage fixes sur leur toit et qui nécessitent donc une interface spécifique. Ce kit se compose tout simplement d’un pont de connexion entre une barre transversale et l’autre (voir photo) en permettant ainsi d’adapter et accrocher facilement la GALERIE UPRACKS aux pieds Rhino-Racks (ou à d’autres) et donc au toit. Avantage supplémentaire de ce système : il est possible de choisir une GALERIE plus large ou plus longue que les standards et, en outre, de la positionner plus en avant ou en arrière suivant vos besoins. L’adaptateur, peut être fixé par les boulons à tête rectangulaire et il est possible de le glisser à l’intérieur de la barre transversale de la GALERIE. Ces exemples concrets illustrent la manière dont les kits UPRACK s’adaptent à toutes les configurations souhaitées. Attention : si vous utilisez les pieds Rhino-Rack, il est nécessaire d’acheter l’adaptateur 63-FKR spécifique. L’emballage est pourvu de 2 adaptateurs, 4 écrous rectangulaires avec leurs boulons, un aimant. Chaque paire d’adaptateurs sert pour une paire de pieds.
32
SPECIAL KITS
63-FKJ15J12 KIT POUR TOYOTA PRADO 150/125
Ce kit est idéal pour installer une galerie UPRACKS sur un Toyota J150/J120/J125 et sans utiliser les fixations Rhino-Rack. Le kit est composé de : 6 x 63-FKRAIL (12 plaques entraxes) 3 x 63-FK001 (3 paires de pieds sans la base) 6 x adaptateurs pour les pieds Ce kit est conçu pour monter les galeries : 63-2112 63-2112P 63-1712 63-1712P
w w w. u p r a c k s . c o m
63-FKJK2 KIT DE MONTAGE COMBO POUR WRANGLER JK 2 PORTES (GALERIE NON INCLUSE) 63-FKJK4 KIT DE MONTAGE COMBO POUR WRANGLER JK 4 PORTES (GALERIE NON INCLUSE)
Joli design et système pour charge très lourde pouvant supporter jusquà 150 kilos sans aucun foret. Cet arceau de sécurité externe permet de monter la bonne galerie de toit (voir les applications sur le site web) sur hard top ou soft top de Jeep Wrangler à partir de 2007. Facile à installer parce que la barre avant est fixée par une base sur le cadre extérieur du pare-brise. La barre arrière est vérouillée par des attaches spéciales et des bagues puis fixée sur un support solide sous le cadre du chassis. Une fois monté, vous pouvez l’utiliser ou vous pouvez le serrer sur les barres transversales de notre galerie de toit Upracks avec la taille que vous préférez. Le kit de montage Combo pèse 37 Kgs, il est fait en acier traité en cataphoresis puis peint avec une peinture époxy poudrée noire.
63-FKPANDA KIT DE PIEDS POUR NOUVELLE FIAT PANDA 2012
Ce système de pied pour lourde charge s’installe en combiné avec des galeries de toit Upracks spécialement conçues. Sur les rails du véhicule d’origine, les pieds spéciaux sont montés selon les 4 points pré marqués des rails OEM. Chaque attache, une fois fixée sur les rails, devient un unique point où vous pouvez fixer la galerie de toit. La cage spécialement dessinée pour cela est la 63-1409 avec les dimensions de 1432.5 X 907 mm. Avec ce système vous pouvez glisser la galerie de toit plus ou moins loin selon votre propre nécessité. La capacité de poids du système complet est de plus de 70 Kgs mais vous pouvez suivre le guide du fabricant automobile préconisant de ne pas dépasser 60 Kgs.
Pour plus d’information et de détails, merci d’aller sur notre site www.upracks.com