www.aasraw.com
How to Make Finished Testosterone Cypionate From Raw Steroid Powders
How to Make Finished Testosterone Cypionate From Raw Steroid Powders...........................................1 Things to prepare............................................................................................................. 2 First–Weigh the Testosterone Cypionate into the glass beaker, add the Benzyl Alcohol and Benzyl Benzoate.........................................................................................................3 Second –The solvents will begin immediately dissolving the powder but in order to speed the process up it is possible to use a water bath....................................................... 3 Then–Add the warmed Cottonseed oil to the solution............................................... 5 Next–Draw up the solutions into the syringe you will be filtering with.....................6 Finally–-Once the product is filtered in the sterile vial the process is complete.Then you can start to use..............................................................................7
1
AASraw Biochemical Technology Co.,Ltd aas14@aasraw.com
www.aasraw.com
In bodybuilding area,there is a hot – selling steroid–Testosterone Cypionate powder，which help to build muscle and strengthen bones,also used for fat loss and sex enhancing.People usually buy Testosterone Cypionate products from online stores.Meanwhile,more bodybuilder tend to buy steroids raw powder because of its low price and not hard manufacturing methods.Today we are here to share a better method to make finished Testosterone Cypionate powder.
Things to prepare
We take Testosterone Cypionate powder 100 mg/mL for example. Each mL of the 100 mg/mL solution contains: Testosterone Cypionate powder……………………………………. 100 mg Benzyl benzoate ……………………………………………………… 0.1 mL Cottonseed oil ………………………………………………………… 736 mg Benzyl alcohol (as preservative)….………………………………… 9.45 mg Syringe (Any size) Sterile Glass Vial (Any size) Needles Thermometer Sterile Syringe filter 22um Digital scales measuring to 0.01g
2
AASraw Biochemical Technology Co.,Ltd aas14@aasraw.com
www.aasraw.com
First–Weigh the Testosterone Cypionate into the glass beaker as shown above, add the Benzyl Alcohol and Benzyl Benzoate.
Second –The solvents will begin immediately dissolving the powder but in order to speed the process up it is possible to use a water bath.
3
AASraw Biochemical Technology Co.,Ltd aas14@aasraw.com
www.aasraw.com
Pace the vial into a few cm of water in a pan or something similar: it is important not to use water that is too hot because this will cause some products to oxidize-150f is a good temperature to use, alternatively boiled water from the kettle. The carrier oil should be the same temperature as the solution when it is added so if you warm the solution in a water bath you should also the same to the carrier oil.
The Complete Guide to Nandrolone Ester (DECA Durabolin)
The objective at this point is simply to fully dissolved the powder into the solvents. There should be no “Hormone swirls� or any visible powder remaining in the solution and once this is achieved move on to the next step.
4
AASraw Biochemical Technology Co.,Ltd aas14@aasraw.com
www.aasraw.com
Then–Add the warmed Cottonseed oil to the solution
this case 736ml must be added. Mix thoroughly again, there should be no hormone swirls-once this occurs remove immediately from the water bath and move on to the filtering process. Above: The steroid powder is fully dissolved in the solvents, the carrier oil is added and the product is ready to be filtered.
5
AASraw Biochemical Technology Co.,Ltd aas14@aasraw.com
www.aasraw.com
Next–Draw up the solutions into the syringe you will be filtering with
this can be a single large syringe or this can be repeated multiple times with a smaller syringe. Remove the 0.22um sterile syringe filter from it’s packing and fix the green needle to the smaller side and then apply to the syringe. Wipe the top of the sterile vial with an Alcohol swab and insert the green needle in it, put the needle attached to the syringe filter into the vial as shown below: Notes: The second needle equalizes the pressure as the solution enters the vial. Apply pressure to the syringe plunger to the filter the mixture. This is the most important part of this entire process as it is what sterilizes your product. All finished steroids from any steroid lab must go through this very process. 6
AASraw Biochemical Technology Co.,Ltd aas14@aasraw.com
www.aasraw.com
Occasionally one may find that the filter gets blocked or that the process slows drastically-it is acceptable to replace the filter with a new one if this occurs to save time. The time it takes to filter steroids depends on which steroid powder is being filtered and how much is being filtere, as well as the mg/ml of the product.
Finally–-Once the product is filtered in the sterile vial the process is complete.Then you can start to use.
7
AASraw Biochemical Technology Co.,Ltd aas14@aasraw.com
