5800CO Carbon Monoxide Detector with Built-in Wireless Transmitter
INSTALLATION AND SETUP GUIDE Table 1: Detector LED Modes
GENERAL INFORMATION
Green LED
Red LED
Sounder
Normal (standby)
Blinks every 10 seconds
Off
Off
Alarm/Test
Off
Blinks every 1 second
Temporal 4 Pattern†
Low Battery
Off
Blinks every 45 seconds for 37 days
Chirp every 45 sec beginning 7 days after LED blinks, continues 30 days
Detector Trouble
Off
Blinks every 5 seconds
One chirp every 45 seconds
Detector End-ofLife
Off
Blinks every 10 seconds
One chirp every 45 seconds
Power Up
Blinks every 10 secs††
Blinks every 10 secs ††
Off
(w/red LED)
(w/green LED)
WARNING: This product is not intended for use in industrial factories or commercial parking garages.
Detector Description • Listed to UL standard 2075 CO sensitivity is evaluated to UL 2034 • Supervised • Local sounder • Dual LED’s • Test/Hush button • Surface mount to wall or ceiling • Optional drywall anchors included
††
MOUNTING THE DETECTOR
Alpha Keypad CO Alarm CO Alarm Lo Bat CO Trouble
detector end-of-life detector trouble tamper
CO Trouble
disarmed = CO Trouble armed = CO Alarm
CS Report CO alarm (CID 162) CO alarm (CID 162) RF low-battery (CID 384) RF sensor supervision (CID 381) sensor trouble - end-of-life (CID 380) RF sensor tamper (CID 383)
MOUNTING SCREWS (INSTALLED)
A
B
B
AL
ARM
A
N OT PA I N T
TEST
E
Event alarms test low battery detector supervision
N M O N OXI D DETECTOR
RBO
L
PROGRAMMING
MA
T N
Figure 1. 5800CO Wireless Carbon Monoxide Detector
NOR
N
5800CO-001-V0
HUSH
HUSH
RED LED
CA
DI AD B C AU T I O N : N SO M AR KING
ST
AL I PA
DO
TE
RM T DO NO M
IN
O ON R N M CTP TE DE
O AR
ALARM
BO
DE
AL
G: WA R N I N O T M OV E
CAR
TI AC O N AL K
XI
GREEN LED
ENGAGE NOTCH WITH TAMPER RELEASE TAB ON BASE AND TURN CLOCKWISE TO LOCK
S T N A IP M P OF E F R L FO O R C K
TEST BUTTON
AN LO GE CK
FL
BATTERY INSTALLATION AND REPLACEMENT
NOTE USE SCREW LOCATIONS A OR B AS REQUIRED, THEN ROTATE BASE AND SECURE SCREWS AT EACH MOUNTING SLOT'S ELBOW.
Figure 2. Mounting the Detector
TAMPER RELEASE TAB (CUT OFF SMALL TAB TO ACTIVATE TAMPER RESIST FEATURE)
5800CO-006-V0
LEDs
AL NORM
O N M O N OXID DETE C TO R
RB
H
CA
PUSH RECESSED BUTTON WITH A 0.18" MAX. DIAMETER TOOL
RECESSED TEST BUTTON
5800CO-004-V0
Figure 5. Recessed Test Button Opening
Testing Signal Strength
BEDROOM
BEDROOM KITCHEN
LIVING ROOM
US
H IO UT K CA AR M
BEDROOM
TEST
N IN : A D G S DIT O N IO N AL B AC K
DO NOT attach the detector to removable ceiling panels. Attach the detector across panel support as shown in Figure 3.
TO BR
E
DO N M ALAR I G: R NIN F WA R E TO M OV PA I N T
Figure 3. Mount Detector Across Ceiling Panel Support
CAUTION
T
O
N A ES LA H RM AIR
5800CO-003-V0
GARAGE CLOSED DOOR
BASEMENT – CARBON MONOXIDE ALARM LOCATION FOR MULTI-LEVEL RESIDENCE
5800CO-005-V0
Figure 4. Detector Location Diagram
Tamper Protection
TESTING THE DETECTOR NOTE:
Testing Programmed Loops
Testing Detector Operation
CAUTION: Carbon Monoxide Gas and its Detection
MAINTENANCE
DETECTOR REPLACEMENT
CAUTION
SPECIFICATIONS
UL standard 2075
Please see insert for Limitations of Carbon Monoxide Detectors.
FOR WARRANTY INFORMATION AND FOR DETAILS REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM, GO TO: www.honeywell.com/security/hsc/resources/wa
2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747
Copyright © 2007 Honeywell International Inc.
K14631V1 4/08 Rev. B
www.security.honeywell.com