Scadapack350e 357e e series datasheet

Page 1

www.aquatechnologygroup.com 800-513-8993 | +1 513-298-1183 sales@aquatechnologygroup.com

SCADAPack 350E | 357E Smart Remote Terminal Units

The SCADAPack™ 300E Smart RTU is a platform built on a 32-bit processor and fitted with a 12...30 Vdc supply, various communication links and a wide range of analog and digital I/O that adheres to open standards and can operate in the harsh demands of a remote environment. The SCADAPack 300E controller may be configured and programmed locally or remotely and is optionally configurable directly from StruxureWare™ SCADA Expert ClearSCADA™ host software. It can play multiple roles simultaneously: end point, automation point, data concentrator, protocol converter, peer-to-peer device and a telemetry router, and use Secure Authentication.

• Data concentrator for DNP3, Modbus and DF1 devices • Communication with up to 13 active SCADA masters, up to 10 remote/local slave devices and up to 100 remote DNP3 devices in peer-to-peer mode • Remote management suite (amend configuration, modify programs and update firmware remotely, using open standard DNP3) • Up to 76 integrated digital/analog inputs/outputs, and more with I/O expansion modules • 1 Ethernet, 3 Serial, 1 USB configuration port • Tool-less DIN rail mounting system • IP2x terminal blocks • Operation from –40 to +70°C (–40 to +158°F)

The SCADAPack 350E/357E Smart RTU provides the following features:

• Cost-effective, compact form factor

• Open-standard telemetry protocols IEC 60870-5-101/ -104 and DNP3 level 4 with Security Suite (Secure Authentication and/or Data Encryption)

When fed from a solar supply, the SCADAPack 350E controller can power its embedded analog inputs/outputs using its integrated auxiliary supply Vloop and 12 to 24 Vdc booster,

• Open-standard industrial protocols Modbus™ RTU/TCP and DF1 master

thus having the ability to switch off this supply to reduce power consumption and help increase battery back-up autonomy.

• Open-standard IEC 61131-3 programming environment


schneider-electric.com

SCADAPack 350E | 357E Smart Remote Terminal Units

Specifications – General characteristics Controller Processor

• 32-bit ARM7 microcontroller, 32 MHz clock, integrated watchdog timer. • Two microcontroller IO co-processors, 20 MHz clock

Memory

• 16 MB FLASH ROM, 4MB CMOS RAM, 4kB EEPROM • CMOS SRAM with lithium battery retains contents for 2 years with no power

Event Logging Capacity (events)

20,000 events

Database Capacity

Up to 1,000 points

Data Concentrator Capacity (points)

Up to 500 in DNP3

Data Concentrator Capacity (devices)

Up to 10 in DNP3 and up to 10 in Modbus or DF1

File System Typical Storage

Internal: 6MB

Communications Serial Port : COM1 Serial Port : COM2

• RS-485, 2-pole removable terminal block, 2-wire, half duplex, supports baud rates up to 115,200 bps • RS-232 port, 8-pin modular RJ45 jack, full or half duplex, or RS-485 port, 2-wire, half-duplex, supports baud rates up to 115,200 bps in RS-232 mode

Serial Port : COM3

RS-232 port, 8-pin modular RJ45 jack, full or half duplex with RTS/CTS control and operator interface power control, supports baud rates up to 115,200 bps

Embedded Wireless

The controller may embed an unlicensed radio module (different options in 900 Mhz or 2.4 Ghz) that uses one of the serial ports

Serial Protocols

DNP3 level 4 slave/master and peer-to-peer, IEC 60870-5-101 slave, Modbus slave/master, DF1 master

Ethernet port

8-pin modular RJ45 jack, 10/100 Mbps UTP (10/100Base-T), transformer-isolated

IP Protocol

• DNP3 level 4 in TCP Master/Slave, UDP Master/Slave and peer-to-peer, IEC 60870-5-104 Slave, Modbus/TCP Server, Modbus/ TCP Client, Modbus RTU in TCP Client • NTP Client/Server, Telnet Server, FTP Server, BOOTP Server

Master – Slave Capability

• Can simultaneously report to up to multiple independent active masters: 3 in DNP3, 2 in IEC 60870-5-101/-104, 5 in Modbus TCP and 3 in Modbus RTU, and connect to up to 100 remote devices in DNP3 peer-to-peer. • As a data concentrator it can manage up to 10 local or remote DNP3 slaves, and up to 10 local slaves communicating with Modbus RTU, Modbus TCP or DF1 serial.

USB Device

USB 2.0 compliant “B”-type receptacle, for local configuration

www.aquatechnologygroup.com 800-513-8993 | +1 513-298-1183 sales@aquatechnologygroup.com

2


schneider-electric.com

SCADAPack 350E | 357E Smart Remote Terminal Units

Specifications – General characteristics General Logic Control

IEC 61131-3 SCADAPack Workbench programming suite (LD, ST, FBD & SFC)

I/O Terminations

SCADAPack 350E: 6, 12-pole connector, 0.0810...3.31mm2 (28...12 AWG), solid or stranded SCADAPack 357E: 5, 6, 7, 9, 10, 12-pole connectors, 0.0810...3.31mm2 (28...12 AWG), solid or stranded

Dimensions

SCADAPack 350E: 211.8mm (8”34) wide, 140.4mm (5.53”) high, 46.5mm (1.83”) deep SCADAPack 357E: 211.8mm (8”34) wide, 181.0mm (7.13”) high, 66.0mm (2.60”) deep

Enclosure

Corrosion resistant zinc-plated steel with black enamel paint

Environment

• Conformally coated • -40°C (-40°F) to 70°C (158°F) operating, -40°C (-40°F) to 85°C (185°F) storage • 5% RH to 95% RH, non-condensing

Shock & Vibration

IEC 60068-2-27 (tested up to 15g), IEC 60068-2-6

Warranty

3 years on parts and labor

Power Rated Voltage

12...30 Vdc. Limit voltage: 11.5...32 Vdc; turn on voltage: 10...11.5 Vdc; turn off voltage: 9...10 Vdc

Maximum Power

12 W at 24 Vdc (internal 5 Vdc supply fully loaded and Vloop on and boosted, fully loaded) • SCADAPack 350E typical power consumption (at 20°C/ 68°F)

Controller LEDs Power Requirements

Use case 1 Use case 2 Use case 3

Vloop fully loaded OFF

OFF

ON ON

12 Vdc

24 Vdc

1.6 W

1.5 W

5.1 W

4.9 W

5.2 W

5.0 W

• SCADAPack 357E typical power consumption: up to 8.9 W (with up to 7 analog input/output loops powered from Vloop supply) Power outputs

Vloop • Maximum 140mA at 12 V (booster turned off) or 24 Vdc (booster turned on); can power up to 7 analog input/output loops

www.aquatechnologygroup.com 800-513-8993 | +1 513-298-1183 sales@aquatechnologygroup.com

3


schneider-electric.com

SCADAPack 350E | 357E Smart Remote Terminal Units

Specifications – Digital and Analog Inputs/Outputs Controller board

Analog Inputs

5, user-selectable 0...10V or 0...20mA plus over range 1, 0...32.7 Vdc (15-bit) for DC supply monitoring • Resolution: 15-bit ADC (15-bit over the measurement range in 10V, 14-bit in 20mA) • Accuracy: ±0.1% of full scale at 25°C (77°F), ±0.2% over temperature range • Input Resistance: 250 Ω or 20 kΩ in 20mA or 10V configurations (60 kΩ for 32.768V) • Normal rejection mode: 27 dB at 60 Hz • Sampling rate: 170 ms

Analog Outputs

2 (optional), 0...20 mA, 4...20 mA, voltage output may be accomplished with external precision resistor • Resolution: 12-bit over 0...20 mA range • Accuracy: ±0.15% at 25°C (77°F), ±0.35% of full scale over temperature range • Response Time: less than 10 μs for 10% to 90% signal change • Power Supply: 12…30 Vdc, external • Power (Current) Requirements: 10 mA plus up to 20 mA per output • Isolation: isolated from RTU logic and chassis • Load Range: 12 Vdc: 0…375Ω, 24 Vdc: 0…925Ω, • Logic End-Of- Scan to Signal Update Latency: typically 18... 27ms • Status & Reporting: output value • Controls: Direct Operate, Select Before Operate

Digital Inputs/Outputs

8, user-selectable as inputs or outputs (open drain) As Digital Inputs • Dry contact • Time stamping: 170ms As Digital Outputs • Sinking MOSFET output, rated 30V, 0.5A, ground return connected to Chassis Ground

Counter Inputs

• 1, 0...10Hz (dry contact) • 2, 0...10kHz (turbine or dry contact)

Internal Power monitor

Power input - analog input and low indication, onboard lithium battery - low indication

Internal Temperature Monitor

Controller temperature range -40°C…+75°C (-40°F...+167°F)

I/O board (357E only) Analog Inputs

8, software-configurable to 0...20, 4...20mA , 0...5 or 0...10V Same features as for the 5 analog inputs located on the controller board (see above) except isolation: • Isolation: 500 Vac from logic and chassis

Analog Outputs

2 (optional), 0...20/4...20mA, voltage output may be accomplished with external precision resistor Same features as for the analog outputs located on the controller board

Digital Inputs

32, 12…24 Vdc • Turn on voltage: 9 Vdc (minimum), Turn off voltage: 4 Vdc (maximum) • Over-voltage tolerance: 150% sustained over-voltage without foreseeable damage • DC input current: 0.67 mA at 24 Vdc • Time stamping : 170ms • Isolation : in group of 8, 1500 Vac from logic supply and chassis

Digital Outputs

16, relays (Form A) • 4 contacts share one common • Isolation : isolated in groups of 4. Isolated from RTU logic, RTU chassis and other groups to 1500 Vac • Maximum Switching Voltage: 30 Vdc or 250 Vac (resistive) • Maximum Switching Load: 150 W or 1250 VA (5 A) • Controls: Direct Operate, Select Before Operate, Trip/Close, Latch, Pulse

Additional I/O Supported modules : • 5606, 5607, 5608 and 5610, and 5304, 5404, 5411, 5414, 5415, 5505 and 5506 I/O Expansion

Maximum number of modules per unit: • SCADAPack 350E: 8 (*) • SCADAPack 357E: 7 (*) (*): to reach this limit, additional power supply modules are required

4


schneider-electric.com

SCADAPack 350E | 357E Smart Remote Terminal Units

Model Code SCADAPack 350E/357E

Model

Select : Controller

TBUP350

SCADAPack350E, Controller 32 bits, 5 Analog Inputs, 8 Digital I/O, 3 High Speed Counter Inputs

TBUP357

SCADAPack357E, Controller 32 bits, comes with the above plus additional I/Os

Code

Select : Platform

E

SCADAPack E Firmware (Configuration Software included), executes two IEC 61131 kernels, Workbench required

Code

Select: SCADA Security

A

None

B

AGA-12 Encryption for DNP3 (Security Administrator application required)

C

DNP3 Secure Authentication SAv2 (Security Administrator application required)

D

DNP3 Secure Authentication with AGA-12 (Security Administrator application required)

Code

Select: Protocol Option

5

DNP3 Serial/IP mstr/slave/peer-to-peer, IEC 60870-5-101/104 Slave, Modbus RTU/TCP mstr/slave, TCP/IP, DF1 mstr

Code

Select: License Option

5

DNP3 Data Concentrator License (limit of 500 points from 10 IEDs), supports multiple DNP3 Masters (up to 3)

7

Adds WITS* protocol (available for SCADA Security Code C and Certification Code S only)

Code

Select : Analog Inputs

A

P350 : 5 selectable as 0...10V or 0...20mA  *P357 : adds 8 selectable as 0...20mA, 4...20mA, 0...5V or 0...10V

Code

Select: Digital Inputs/Outputs

A

P350 only: 8 Digital I/O, individually selectable as digital input (Dry Contact) or digital output (Open Drain)

B

P357 only: adds 32 digital inputs (12-24V), 16 digital outputs (Dry Contact relay for Class I Div 2, Solid State relay for IECEx/ATEX)

* WITS protocol (Water Industry Telemetry Standard)

5


schneider-electric.com

SCADAPack 350E | 357E Smart Remote Terminal Units

Model Code SCADAPack 350E/357E

Code

Select: Analog Outputs

0

None

1

2 channel Analog Output, 0..20 mA, external DC supply

2

P357 only : 4 channel Analog Output, 0..20 mA, external DC supply

Code

Select : Integrated Communications Interfaces

0

None FreeWave™ & MDS™ Radios (requires one RS232 port)

1

900Mhz FreeWave Spread Spectrum Radio

A

900MHz MDS Spread Spectrum Radio Trio™ Radios – 900MHz (requires one RS232 port)

B

900MHz Trio Spread Spectrum Radio with encryption, 902-928MHz (FCC / IC)

C

900MHz Trio Spread Spectrum Radio with encryption, 915-928MHz (AUS)

D

900MHz Trio Spread Spectrum Radio, 915-928MHz (BRAZIL)

E

900MHz Trio Spread Spectrum Radio, 921-928MHz (NZ) Trio Radios – 2.4GHz (requires one RS232 port)

J

2.4GHz Trio Spread Spectrum Radio, ETSI/100mW, ATEX (EUROPE)

K

2.4GHz Trio Spread Spectrum Radio with Encryption, 500mW (CANADA, USA & AUSTRALIA)

L

2.4GHz Trio Spread Spectrum Radio, 500mW (OUTSIDE OF EUROPE, CANADA, USA & AUSTRALIA)

Code

Selection: Certifications

S

With FCC, UL508, CE marking and RCM

X

Adds IECEx/ATEX Class I, Zone 2

U

Adds cCSAus Nonincendive Electrical Equipment for use in Class I, Division 2, Groups A, B, C and D

Disclaimer: Not all product features are available in every mode of operation. Schneider Electric reserves the right to change product specifications. For more information visit www.schneider-electric.com.

6


schneider-electric.com

SCADAPack 350E | 357E Smart Remote Terminal Units

www.aquatechnologygroup.com 800-513-8993 | +1 513-298-1183 sales@aquatechnologygroup.com

Telemetry & Remote SCADA Solutions 415 Legget Drive, Suite 101, Kanata, Ontario K2K 3R1 Canada Direct Worldwide: +1 (613) 591-1943 Fax: +1 (613) 591-1022 Toll Free within North America: +1 (888) 267-2232 www.schneider-electric.com

Part Number TBULM08002-92  v27 © 2016 Schneider Electric. All Rights Reserved. Schneider Electric, Life Is On, Struxureware, ClearSCADA, Modbus, SCADAPack and Trio are trademarks and the property of Schneider Electric SE, its subsidiaries and affiliated companies. All other trademarks are the property of their respective owners – February 2016

7


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.