Porcelaingres General Catalogue

SMART BOOK 2023

Note: Visit our website for other languages.

PRODUCT FINDER

Find your product according to your needs and destination of use.

About us Identity

We are part of the Italian IRIS CERAMICA GROUP

and we are among the major manufacturers of porcelain stoneware slabs in Germany. In the production site in Vetschau, Brandenburg, 100 km south-east of Berlin, we produce exclusive technical ceramic slabs for floors and walls in one of Europe’s most modern production lines. With a range of surfaces and many decorations, the ceramic slabs can be used in a wide range of projects, meeting all kinds of style demands. We consider ourselves a reliable partner for architecture and design firms, offering competence and experience at all levels.

High-tech production

2002 Foundation

84.000 m2

Production Area

220 + Employees

The production processes are accurately monitored by robotics, to create porcelain stoneware slabs that are always of the highest quality and strength.

4.5 milion m2 Production Capacity

Green mission Identity

The sustainability of ceramic

Our avant-garde production plant in Vetschau meets high standards of environmental sustainability: 40% of the raw materials it uses come from recycled and natural materials, rainwater and water from production processes is reclaimed and put back in circulation.

Vetschau plant is strategically located by the railway station and the motorway, and the supplier of natural raw materials is located only 200 km away, cutting CO2 emissions by travelling only a short distance. Green hydrogen will be introduced to produce clean, circular energy.

Our products comply with LEED® IEQ 4 Lowemitting materials – floor systems, have no VOC (volatile organic compounds) emissions, and are 100% recyclable and chemically inert, so that they will not give off hazardous gases even in the event of fire.

Several Porcelaingres products have received the British BREEAM certification as well as LEED certification from the US Green Building Council.

• Photovoltaik arrays generating 20% of the plant’s annual energy requirements

On the 795 metre-long roof of the production site in Vetschau, we have installed a photovoltaic plant that produces a peak power of 2.4 megawatts.

• Saving 1,3 mio m³ of gas per year = reduce 3.000 tons CO2

In 2019 installation of heat recovery inside production.

• Saving up to 5.000 m³ of clean water per year

In 2021/2022 installation of dry cutting system.

• Recycling & Reusage:

In our factory we recycle all production waste:

- 7.150 tons of powder and unburnt tiles

- 10.500 tons of burnt production waste

- all water needs inside production and usage of rainwater

New Generation Fullbody

Fullbody generation porcelain stoneware surfaces are characterized by a uniform, indestructible, waterproof and very durable body. This is compressed by a high pressure and fired at very high temperatures (1300°) to ensure maximum resistance, hygiene and stain resistance. slabs for yourself.

More than design

The design of each piece is unique, modern and never uniform thanks to a harmonious and random mixture of granules and flakes of different colors and dimensions. Due to our modern production facilities and cuttingedge expertise, fragments and coloured base mixtures come together in various ways, to simulate the unpredictability of nature and hand-made objects which gives the impression of using whole stone slabs.

Collection with

Rounded double straight edge

Squared 45° edge

Squared straight edge

Bull nose

CLEAN + Innovation

A velvet surface with grip and comfort of care

The new technological processing of the porcelain stoneware surfaces with the aid of micro-sandblasting during the production process provides a softer touch. As a result, the surface is not only pleasant to the touch, but also guarantees better cleaning results. At the same time, the grip improves to a slip resistance class of R11 A+B.

The porcelain stoneware surfaces with the CLEAN+ surface finishing are marked with this seal on our website.

CLEAN + TACTILE SURFACE EASY TO CLEAN

Our 20mm collections with CLEAN+

URBAN

SOFT CONCRETE ROYAL STONE

NATIVE STONE LOFT QUARTZ STONE IN WOOD

18 - 23

24 - 29

38 - 43

44 - 49

50 - 55

56 - 59

100 - 103

The new surface finish CLEAN+ is applied to our 20 mm tiles.

20 mm outdoor porcelain stoneware is the product with the highest technical performance, ideal for flooring in outdoor environments. Resistant to frost and thermal shock, it has heightened grip characteristics and is easy to clean. The perfect union between high technical performance and aesthetics.

More slip resistance

GRIP+, the groundbreaking surface finishing for selected Porcelaingres floor tiles, unfolds its full strength wherever it gets wet and damp. This is because GRIP+ actively reduces the risk of slipping on the floor when exposed to moisture. Thanks to their innovative microcrystals, these new tiles have a lifelong durability of their slip resistance class A+B. Thus they meet the requirements for barrier-free family bathrooms and ageappropriate bathroom renovations.

Reliable

Actively reduces the risk of slipping when exposed to moisture.

Durable

Innovative microcrystals with life-long durability.

Easy to clean

The surface offers the best conditions for effortless cleaning.

Safe

Free of toxic chemicals to keep you and your family safe.

Anthracite

Finishings

Anthracite_weave decor

Specials Decor

Urban Dove Urban Dove_weave decor

Urban Grey Urban Grey_weave decor

Features

Urban Sand Urban Sand_weave decor

GRIP +

More slip resistance

CLEAN +

Easy to clean

Urban Ivory Urban Ivory_weave decor

Inspiration

Visit the collection webpage in other languages.

Urban White Urban White_weave decor

URBAN

Product details

*Production upon request

URBAN

Product details

The shade variation index is a rating to determine tile variation between individual pieces of the same color group.

*Production upon request

SOFT CONCRETE Collection summary

Soft White Soft Beige

Soft White_hexagon decor

Finishings

Natural

Formats

100 × 100 - 120 × 60 60 × 60 - 60 × 30

Specials

Decor - Mosaic - Bullnose - Step

Soft Beige_hexagon decor

Thicknesses

6 - 8 - 20 mm

Skid Resistances

R10 A+B UGL

R11 A+B+C UGL

Soft Brown Soft Silver Soft Iron

Soft Brown_hexagon decor

Features

GRIP + More slip resistance

CLEAN +

Easy to clean

Soft Silver_hexagon decor

Inspiration

Visit the collection webpage in other languages.

Soft Iron_hexagon decor

SOFT CONCRETE

Product details

SOFT CONCRETE

Product details

*Production upon request

GRIP + GRIP +

GRIP + GRIP + GRIP +

STARDUST

Finishings

Natural

Specials

Decor - Mosaic - Bullnose - Step

Thicknesses

6 - 8 mm

Skid Resistances

R10 A+B UGL Features

LOOK + Full body generation

GRIP + More slip resistance

Inspiration

Visit the collection webpage in other languages.

STARDUST

Product details

*Production upon request

URBAN GREAT Collection summary

Finishings

Thicknesses

Skid Resistances

Inspiration

Visit the collection

in other languages.

URBAN GREAT

Product details

Packaging details 120 - 129 Technical product features at page 108 - 109

Note

All articles of the GREAT collections are produced on order in Castellarano factory (Italy).

NATIVE STONE Collection summary

Finishings

Cloudy White Cloudy White_decor

Specials

Mystic Grey Mystic Grey_decor

Alver Beige

Alver Beige_decor

Dusky Greige

Dusky Greige_decor

GRIP + More slip resistance

CLEAN + Easy to clean

Mineral Black

Mineral Black_decor

Inspiration

Visit the collection webpage in other languages.

Authentic Brown

Authentic Brown_decor

NATIVE STONE

Product details

NATIVE STONE

Product details

*Production upon request

Black Diamond

Imperial Brown

Palladium Grey

Noble Beige

Platinum White

ROYAL STONE

Product details

ROYAL STONE

Product details

*Production upon request

Finishings

Specials

Thicknesses

Skid

Features

Inspiration

Visit

Loft Sand

Loft Snow

LOFT

Product details

*Production upon request

LOFT

Product details

*Production upon request

Finishings

Structured

Formats

120 × 60 - 60 × 60

Thicknesses

20 mm

Skid Resistances

R11 A+B+C UGL

Features

CLEAN + Easy to clean

Inspiration

Visit the collection webpage in other languages.

QS Beige

QS Grey

QS Black

QS Superblack

QUARTZ STONE

Product details

Finishings

Natural

Formats

100 × 100 - 120 × 60 - 120 × 30 60 × 60 - 60 × 30

Specials

Decor - Mosaic - Bullnose - Step

Thicknesses

6 mm

Skid Resistances

R10 A+B UGL

Features

GRIP + More slip resistance

Inspiration

Visit the collection webpage in other languages.

Black Chiffon Velvet Brown

Shantung Greige Vanilla Lace

White Satin Light Ornament

Dark Ornament

SILK STONE

Product details

*Production upon request

GREAT ROYAL STONE Collection summary

in other languages.

GREAT ROYAL STONE

Product details

Note

All articles of the GREAT collections are produced on order in Castellarano factory (Italy).

GREAT ELITE Collection summary

Finishings

Honed Bright Satin

Formats

270 × 120 - 120 × 120

Thicknesses

6 mm

Skid Resistances

R9 UGL

Inspiration

Visit the collection webpage in other languages.

Elite Alpi

Elite Calacatta

Elite Noir

Elite Marquina

Elite Statuario

Elite Invisibile

GREAT ONE Collection summary

Finishings

Honed Bright

Formats

270 × 120 - 120 × 120

Thicknesses

6 mm

Skid Resistances

R9 UGL

Inspiration

Visit the collection webpage in other languages.

One White

GREAT ELITE - ONE

Product details

Packaging details 120 - 129 Technical product features at page 112 - 113

GREAT ONE

The

is a rating to determine tile variation between individual pieces of the same color group.

Note

All articles of the GREAT collections are produced on order in Castellarano factory (Italy).

Porcelaingres reserves the right to modify technical details included in this catalogue as well as irregularities in the grain.

COLOR STUDIO

Finishings

Natural

Formats

Night Sage

100 × 100 - 120 × 60 60 × 60 - 60 × 30

Specials

Mosaic - Brick Mosaic - Listel

Rhombus - Triangle - Trapezoid

Parallelogram - Square

Bullnose - Step

Powder White

Thicknesses

6 mm

Skid Resistances

R9 A UGL

Inspiration

Visit the collection webpage in other languages.

Brown Biscuit

Malt Cream

COLOR STUDIO

Product details

*Production upon request

COLOR STUDIO

Product details

*Production upon request

JUST GREY

Finishings

Natural - Structured

Formats

120 × 60 - 60 × 60 - 60 × 30

Specials

Mosaic - Bullnose - Step

Thicknesses

8 mm

Skid Resistances

R10 A UGL

R11 A+B+C UGL

Inspiration

Visit the collection webpage in other languages.

Super Black Black

Dark Grey Grey

Mid Grey Light Grey

White Super White

JUST GREY

Product details

*Production upon request

JUST BEIGE

Finishings

Natural - Structured

Formats

60 × 60

Specials

Mosaic - Bullnose - Step

Thicknesses

8 mm

Skid Resistances

R10 A UGL

R11 A+B+C UGL

Inspiration

Visit the collection webpage in other languages.

Super Brown Dark Brown

Brown

Mid Brown

Light Brown Beige

Gold Beige Light Beige

JUST BEIGE

Product details

The shade variation index is a rating to determine tile variation between individual pieces of the same color group.

*Production upon request

Finishings

Natural Formats

100 × 100 - 120 × 60 60 × 60 - 60 × 30

Specials

Mosaic - Bullnose - Step

Thicknesses

6 mm

Skid Resistances

R9 UGL

Inspiration

Visit the collection webpage in other languages.

Shabby Black

Shabby Brown

Shabby Grey

Shabby White

RADICAL

Product details

*Production upon request

Specials

Zinc Titanium

White Iron

GREAT METALS

Product details

Packaging details 120 - 129 Technical product features at page 114 - 115

The shade variation index is a rating to determine tile variation between individual pieces of the same color group.

Note

All articles of the GREAT collections are produced on order in Castellarano factory (Italy).

PURE WOOD Collection summary

Finishings

Natural Formats

120 × 20

Specials

Bullnose

Thicknesses

6 mm

Skid Resistances

R10 A+B UGL Features

GRIP + More slip resistance

Inspiration

Visit the collection webpage in other languages.

Pure Grey

Pure Amber

Pure Hazel

Pure Brown

Pure Black

Pure White

PURE WOOD

Product details

Finishings

Specials

Modul Oblique - Modul Shade

Bullnose

Thicknesses 8 - 20 mm

Skid

Features

CLEAN + Easy to clean

Inspiration

Visit the collection webpage in other languages.

IN WOOD

Product details

*Production upon request

Technical Information

Certifications

Sensitivity towards ethycal, environmental, safety and quality issue

ISO 9001 certification: for corporate Quality system management. The certification, valid at an international level, concerns corporate management in its entirety, from research and development to production, and from distribution to customer support. This system certifies that the Company has implemented an internal quality management system.

The certification is available at www.porcelaingres.com/downloads/

ISO 50001 certification: for organizations committed to addressing their impact, conserving resources and improving the bottom line through efficient energy management. The standard specifies the requirements for establishing, implementing, maintaining and improving an energy management system, whose purpose is to enable an organization to follow a systematic approach in achieving continual improvement of energy performance, including energy efficiency, energy security, energy use and consumption.

The certification is available at www.porcelaingres.com/downloads/

CE MARK - It indicates that Porcelaingres products comply with the requirements of 305/2011 UE directive – in particular with regard to health production and the users and consumers’ safety – and may thus be freely circulated on the Community market. For the declarations of conformity of each single product, please refer to: www.porcelaingres.com/downloads/

The China Compulsory Certificate mark, commonly known as a CCC Mark, is a compulsory safety mark for our Great Format products imported, sold or used in the Chinese market.

The certification is available at www.porcelaingres.com/downloads/

EPD (Environmental Product Declaration): a voluntary type III product declaration, based on analysis of the product life cycle (with a “from cradle to grave” approach) in accordance with the EN 15804 standard. This declaration is drawn up with reference to the guidelines of the UNI EN ISO 14040 standard and the specific PCR (Product Category Rules). This document describes the environmental impact linked to the entire life cycle of a specific quantity of product. Our Company was the first to certify its products (see www.environdec.com) with specific EPD, validated by an independent third-party Body.

Recording no. S-P-01439 can be found on the website www.environdec.com

LEED certification: already widespread and active in more than 40 countries, the LEED (Leadership in Energy and Environmental Design) certification system assesses and attests to the environmental, social and economic sustainability of buildings considered as a whole. According to the LEED classification criteria, highly environmentally sustainable construction materials contribute to achieving credits and increasing the points for the building. All the slabs presented in this instrument are certified to contain percentage of recycled material higher than 40% in accordance with the ISO 14021 standard, thus guaranteeing the highest points according to the LEED system.

BREEAM certification it is the most widespread standard in the world and it is designed to measure the environmental impact of buildings by applying specific criteria for assessing the sustainability of the construction. The rating system requires types of certification determined by strict technical parameters and quality control which in turn are based on the most recent technology and knowledge available.

The updated list of certified collections is available at www.porcelaingres.com/downloads/.

UPEC classification associated with the QB certification mark attests to the compliance of floor and wall coverings with the technical requirements set out in certification reference documents. It assigns classifications of use indicating that the durability of a product is appropriate for use on specific types of premises.

The list of the certified products is available at http://evaluation.cstb.fr/

Technical product features

Declared values of production

Technical product features

Declared values of production

Technical product features

Declared values of production

Technical product features

Declared values of production

Cleaning & Maintenance

Instructions for porcelain stoneware slabs

As our porcelain slabs are fired at 1250 C°, this results in a very dense surface which is impenetrable to contamination.

If contamination occurs, it is only on the surface of the tile and can easily be removed. The recommendations for cleaning and maintenance listed below are for Porcelaingres porcelain stoneware slabs with a natural or textured surface.

1. Initial cleaning after installation

2. Regular maintenance cleaning

3. Intensive basic cleaning as needed

4. Calcareous (hard) water

5. Outdoor areas

Special instructions regarding initial cleaning, regular maintenance cleaning and care of our slabs with a smooth surface will be provided to you on request by our technical support.

Furthermore, special instructions should be observed for the initial cleaning of grouting with epoxy resin and slabs with a metallic appearance. These are also available on request.

1.Initial cleaning after installation

After laying and grouting the floor covering with cement sealing compounds and joint sealants, cement residues will often remain on the surface despite careful cleaning with clear water. These are not always immediately recognisable. Various contaminants can later become stuck to the residues. Some cement from the top layer of cement joints will also dissolve during the first maintenance cleanings. This process is normal and will steadily decrease.

Therefore, it may be necessary to repeat the instructions listed below for the initial cleaning, for up to two months after laying the slabs.

A cement remover (eg Lithofin KF cement remover or Fila Deterdek) will clean the cement residue from the surface after laying and grouting. Also, much of the “loose” cement will immediately be removed from the top layer of the cement joints.

As described above, subsequent repeated treatment will be necessary after the few first maintenance cleanings. The cement remover is an acidic aqueous solution or an “acidic cleaner” with a ph-value of approximately 1 (concentrate).

Please soak the joints before use and follow the manufacturer’s instructions for the cleaning agent.

When using flexible grouts, additional cleaning with an intensive stoneware cleaner (e.g. Lithofin KF Intensive Cleaner or Fila PS 87) may be necessary due to plastic components in the grout. The plastic particles may also accumulate on the surface of the porcelain stoneware slabs. This cleaner dissolves the plastic compounds and the plastic can be removed with a microfibre mop. The intensive stoneware cleaner is an alkaline (basic) cleaning agent with a pHvalue of approximately 14 (concentrate).

2.Regular maintenance cleaning

For routine maintenance, and for cleaning away light dirt, it is enough in most cases to use warm water with a dash of vinegar or vinegar cleaner with a microfibre mop or microfibre washcloth. The vinegar or vinegar cleaner binds to the permanently present lime in the water used for cleaning.

For greasy contaminants, instead of vinegar, use a porcelain stoneware care cleaner (eg Lithofin KF Care Cleaner or Fila Cleaner). This cleaner is a mildly alkaline cleaning agent with a pH-value of approximately 10 (concentrate). Under no circumstance should cleaning agents (e.g. washing-up liquid) with waxy and film-forming ingredients be used.

If this cleaning agent is used, it will result in barely soluble layers of wax forming on the surface of the slabs. The wax forms into a layer of “glue”, which in turn promotes the adhesion of dirt and contaminants.

At first, these unwanted wax layers cannot be seen, or can only be seen against a strong light. Layers which have been forming for a longer amount of time result in visible grey deposits on the joint edges. The resulting residue can only be removed through intensive basic cleaning (e.g. using Lithofin KF Intensive Cleaner or Fila PS 87).

Hint: Porcelain stoneware has a similar surface to glass, therefore cleaning can be done using similar methods.

3.Intensive basic cleaning as needed

If the slabs are very dirty, come under heavy use or if there is a formation of dirt layers, basic cleaning with an intensive porcelain stoneware cleaner is necessary.

Cleaning & Maintenance Instructions for porcelain stoneware slabs

A porcelain stoneware cleaner (e.g. Lithofin KF Intensive Cleaner or Fila PS 87) is an alkaline (basic) cleaning agent with a pH-value of approximately 14 (concentrate).

This cleaning agent dissolves dirt and should be rinsed off with clean water and a microfibre mop. Preferably, the dirty water can be sucked up with a wet vacuum cleaner, as this cleaning device sucks up liquid from the deeper grooves efficiently.

The information of the various manufacturers must be observed.

4. Calcareous (hard) water

Calcareous water can cause deposits of lime to accumulate on the surface of the slabs. The resulting “greyness” appears stronger on darker slabs.

When using natural soap, the lime/salts contained in the water can, together with the soap, combine to produce light/grey hard-to-remove residues of lime soap.

To avoid such deposits, as little water as possible should be allowed to remain and dry out on the slabs after cleaning or showering. In the shower, removal with window rubber has proven to dry the tile covering effectively. Also, a second drying using a dry cloth can effectively inhibit the formation of calcium deposits.

Nevertheless, it may be necessary to periodically clean the slabs with a (slightly acidic) acidcontaining cleaning agent for sanitary facilities (Lithofin KF Sanitary Cleaner; 1:15 diluted). This cleaner is particularly suitable for removing limescale.

Hint: For wiping, it is possible to use a microfibre cloth. A lot of dirt attaches itself to the fibres of microfibre cloth. The dirt particles can then easily be rinsed away under cold or hot water. For cleaning and maintaining larger areas, a cleaning machine is recommended.

5. Outdoor areas

Like all products used outdoors, porcelain stoneware slabs are also subject to constant influences from the environment or surface usage. These influences are not only dependent on the local conditions (e.g. covered areas, shady areas under trees, etc.) but also on the priority use of the surface (e.g. garden path, entrance, driveway, etc.).

Due to the required high slip resistance of porcelain stoneware slabs, there may be rubber marks from tyres or shoes, e.g. at garage entrances, doorways and walkways.

Such traces are unavoidable and do not indicate a defect of the finished products. They can also be removed by targeted cleaning.

Basically, however, one can say that the more visible contaminants have become, the brighter, smoother and more homogeneous is the surface. For darker, multi-coloured or structured products, dirt is not generally as much of a problem.

Normal contamination of porcelain stoneware surfaces (eg., due to soil, or dust) can usually be cleaned away with a stiff brush or broom and running water. Dirty rubber marks, and also oil/grease contamination can be treated using a porcelain stoneware cleaner (e.g. Lithofin KF Intensive Cleaner or Fila PS 87). Mix the cleaning agent according to the manufacturer’s instructions, apply to the slabs, leave it to act, then scrub with a brush or white scouring pad before rinsing away with lots of clean water.

Spots which arise, for example, due to strong colour-bleeding leaves or petals can be minimized by a fast removal of the cause. Prolonged exposure to contamination must be treated with a porcelain stoneware intensive cleaner.

For coarse contaminants, such as oil, grease or moss, a wide variety of especially suitable cleaning agents are commercially available. These should be applied according to the manufacturer’s instructions.

Cleaning and care products of the manufacturer Lithofin have proven to be particularly suitable. For more information regarding the products of Lithofin please visit www.lithofin.de

Please be sure to observe the manufacturer’s instructions and recommendations. Set up a small test area and, in case of doubt, contact the manufacturer or our technical support.

Packaging Details

Crate with pudding layers

- minimum order: 2 slabs per crate;

- no more than 6 items ( colors) per crate allowed;

Loading on lorry:

- stack max. 6 crates on lorry;

- max. 24 crates on lorry (4 spaces) within total weight limits;

- option of placing 2 euro-pallets next to each stack Size: 325 × 113 ×

- minimum order: 3 slabs per crate;

- no more than 6 items ( colors) per crate allowed;

Loading on lorry:

-stack max. 5 crates on lorry;

- max. 32 crates on lorry (8 spaces) within total weight limits;

- option of placing crates next to each other

- minimum order: 3 slabs per crate;

- no more than 6 items ( colors) per crate allowed;

Loading on lorry:

-stack max. 5 crates on lorry;

- max. 32 crates on lorry (8 spaces) within total weight limits;

- option of placing crates next to each other Size: 172 × 163 × h.41 cm

- minimum order: 4 slabs per crate;

- each crate must contain an even number of slabs per item;

- no more than 6 items (colors) per crate allowed;

Loading on lorry:

- stack max. 5 crates on lorry;

- max. 28 crates on lorry (7 spaces) within total weight limits;

- option of placing 1 euro-pallet next to each stack

Packaging Details

- one rack may contain up 5 different items ( colors);

- the rack must be filled to the maximum capacity specified;

- in order to optimise space, this rack may be filled with 48 slabs (instead of 2 racks with 24 slabs each)

one rack may contain up 5 different items (colors); - the rack must be filled to the maximum capacity specified Size: 312 × 74 × h.140

- one rack may contain up 5 different items ( colors);

- the rack must be filled to the maximum capacity specified;

- in order to optimise space, this rack may be filled with 48 slabs (instead of 2 racks with 24 slabs each)

- one rack may contain up 5 different items (colors);

- the rack must be filled to the maximum capacity specified

- one rack may contain up 5 different items ( colors);

- the rack must be filled to the maximum capacity specified;

- in order to optimise space, this rack may be filled with 48 slabs (instead of 2 racks with 24 slabs each)

Size: 161 × 74 × h.191 cm

- one rack may contain up 5 different items (colors);

- the rack must be filled to the maximum capacity specified

Packaging Details

- minimum order: 2 boxes (= 2 slabs);

- each crate must contain an even number of slabs/boxes;

- one tall crate may contain up 3 different items (colors) for the same size while the short crate only 2 different items;

Loading on lorry:

- stack max. 3 tall crates on lorry;

- max. 30 tall crates on lorry (15 spaces) within total weight limits

- minimum order: 1 box (= 2 slabs):

- one tall crate may contain up 3 different items (colors) for the same size while the short crate only 2 different items; Loading on lorry:

- stack max. 3 tall crates on lorry;

- max. 30 tall crates on lorry (15 spaces) within total weight limits

- minimum order: 1 box (= 6 slabs):

- one tall crate may contain up 3 different items (colors); for the same size while the short crate only 2 different items;

Loading on lorry:

- stack max. 3 tall crates on lorry;

- max. 30 tall crates on lorry (15 spaces) within total weight limits

- minimum order: 1 box (= 2 slabs):

- one tall crate may contain up 3 different items (colors) for the same size while the short crate only 2 different items;

Loading on lorry:

- stack max. 3 tall crates on lorry;

- max. 44 tall crates on lorry (22 spaces) within total weight limits Size: 121 × 112 × h.65 cm

- minimum order: 1 box (= 2 slabs):

- one tall crate may contain up 3 different items (colors) for the same size while the short crate only 2 different items;

Loading on lorry:

- stack max. 3 tall crates on lorry;

- max. 44 tall crates on lorry (22 spaces) within total weight limits

- minimum order: 1 box (= 3 slabs):

- one tall crate may contain up 3 different items (colors) for the same size while the short crate only 2 different items;

Loading on lorry:

- stack max. 3 tall crates on lorry;

- max. 30 tall crates on lorry (15 spaces) within total weight limits

Packaging Details

- minimum order: 1 box (= 2 slabs):

- one tall crate may contain up 3 different items (colors) for the same size while the short crate only 2 different items;

Loading on lorry:

- stack max. 3 tall crates on lorry;

- max. 30 tall crates on lorry (15 spaces) within total weight limits

- minimum order: 1 box (= 2 slabs):

- one tall crate may contain up 3 different items (colors) for the same size while the short crate only 2 different items;

Loading on lorry:

- stack max. 3 tall crates on lorry;

- max. 30 tall crates on lorry (15 spaces) within total weight limits

- minimum order: 1 box (= 6 slabs):

- one tall crate may contain up 3 different items (colors); for the same size while the short crate only 2 different items;

Loading on lorry:

- stack max. 3 tall crates on lorry;

- max. 30 tall crates on lorry (15 spaces) within total weight limits

- minimum order: 1 box (= 2 slabs):

- one tall crate may contain up 3 different items (colors) for the same size while the short crate only 2 different items;

Loading on lorry:

- stack max. 3 tall crates on lorry;

- max. 44 tall crates on lorry (22 spaces) within total weight limits Size: 121 × 112 ×

- minimum order: 1 box (= 2 slabs):

- one tall crate may contain up 3 different items (colors) for the same size while the short crate only 2 different items;

Loading on lorry:

- stack max. 3 tall crates on lorry;

- max. 44 tall crates on lorry (22 spaces) within total weight limits

- minimum order: 1 box (= 3 slabs):

- one tall crate may contain up 3 different items (colors) for the same size while the short crate only 2 different items;

Loading on lorry:

- stack max. 3 tall crates on lorry;

- max. 30 tall crates on lorry (15 spaces) within total weight limits

Packaging Details

Container

Package informations

20 FOOT CONTAINER

Size: 5,90 × 2,32 × h. 2,35 meters

Tailor-made packaging

Max. capacity

40 FOOT CONTAINER

Size: 11,90 × 2,33 × h. 2,35 meters*

• 6 crates 300×150;

• 10 crates 300×100 + 5 crates 150×150;

• 10 crates 300×100 + 10 tall crates 150×100;

10 crates 300×100 + 6 tall crates 75×37,5\75×75\150×75;

• 10 crates 300×100 + 12 tall crates 100×100;

• 15 crates 150×150 + 3 tall crates 75×37,5\75×75\150×75;

• 12 tall crates 120×120 (within weight limits); 27 tall crates 100×100 (within weight limits);

• 18 tall crates 75×37,5\75×75\150×75;

• 18 tall crates 150×100

18 crates 300×150;

• 30 crates 300×100 + 5 crates 150×150;

• 30 crates 300×100 + 6 tall crates 75×37,5\75×75\150×75;

• 30 crates 300×100 + 6 tall crates 100×100;

30 crates 300×100 + 10 tall crates 150×100;

• 24 tall crates 120×120 (within weight limits);

• 35 tall crates 150×150 (within weight limits)

Important recommendations

*concerning the 120×120, 100×100 or 75×37,5\75×75\150×75 formats, calculation must take weight into account (the space is never completely filled as weight would be exceeded)

FINDER

Formats

Find your product according to your needs and destination of use.

Specials

Find your product according to your needs and destination of use.

Specials

Find your product according to your needs and destination of use.

Skid Resistances

Find your product according to your needs and destination of use.

DIN EN 16165 - Annex B

This method aims to measure the tiles suitability for laying in areas where people walk footwear. Defining the “R-value” of the surfaces according to the table below.

DIN EN 16165 - Annex A

This method aims to measure the surfaces suitability for laying in areas where people walk barefoot. Given an “A, B and C” value according to the table below.

Porcelaingres GmbH

Irisstraße 1

03226 Vetschau – Deutschland

Tel +49 (0)35433 / 597-0

Fax +49 (0)35433 / 597-170

Castellarano Showroom

Via Guido Reni 2

42014 Castellarano (RE) - Italy

Porcelaingres by GranitiFiandre

Via Radici Nord 112

42014 Castellarano (RE) - Italy

Tel +39 0536 819611

Fax +39 0536 858082

Fax +39 0536 850088

www.porcelaingres.com

info@porcelaingres.com

USEFUL RESOURCES

Our aim is to support our customers from the design phase through to installation and maintenance. Visit "www.porcelaingres.com/Downloads"

Certifications

Technical Data

Manuals

Catalogues

KEEP UP-TO-DATE WITH OUR APP

Search “PORCELAINGRES” on your app store

www.porcelaingres.com/pdfapp

Colors and decors reproductions are approximate. All rights are reserved. Total or partial reproduction of text or illustrations of this catalogue is prohibited and is subject to legal sanctions. The tables with the data referred to the content per box and to the packing weight are update at the catalogue printing time; therefore the listed data can be altered.

© 2023 Porcelaingres GmbH - All rights reserved. Updated in February 2023