Classic DrainTop Advanced Laboratory Liquid Control Systems Differentiate your laboratory case work with Classic DrainTops. Laboratory Tops now offers this unique epoxy resin worksurface to improve performance in lab sink areas.
Directional Containment Advanced liquid control begins with the Classic DrainTop’s raised outer marine edge. This integrally molded safety barrier surrounds the worksurface preventing most spills and splashes from overflowing onto lab techs, case work and lab flooring. The specialized DrainTop surface directs liquids toward the sink with a slight pitch. This increases the height of the containment barrier around the sink’s splash zone.
Raised Rib Drainboards DrainTops incorporate Laboratory Tops’ exclusive rolling rib drainboard design. These durable ribs elevate laboratory glassware above the worksurface which increases air flow in and around wet items and reduces drying times. The smooth rib surfaces are molded to eliminate absorption and ease clean ups. Thorough cleaning prevents residual chemicals from mixing in the sink area and reduces the staining typical with machined drain grooves. Combined with good housekeeping practices, the DrainTop can retain its good looks for the life of the lab!
Elevated Fixtures Faucets, eyewashes and other services can be mounted on the large elevated rear deck. Elevating fixtures above the wet area helps protect them against corrosive chemical and moisture damage and eliminates the possibility of standing water seeping into the sink cabinet through the fixture hole (please check gooseneck specs to ensure sink rim clearance).
DropIn Sinks LabTops速 DropIn速 Sinks with SolTra速 Outlets complete the Classic DrainTop liquid control system. All sink rims, corners and outlet transitions are radiused and the basin is pitched toward the outlet to facilitate complete drainage. Many sink sizes and double sink combinations can be specified.
DrainTops are Available Exlusively from
Cutaway - Side View
Classic DrainTop Sizes
Classic DrainTops are available to meet many standard size requirements. Back rails can be trimmed to accommodate additional worksurface dimensional requirements (see table below).
Edge Options
Select DrainTops with either a 1/8” bevel or a 1/4” radius exposed edge. These attractive worksurfaces can be used throughout the lab at the end of islands, peninsulas and in wall runs in-line with other ClassicTops.
Edge Options
DropIn® Sinks
Classic DrainTops are excellent platforms for LabTops’ Epoxy Resin DropIn sinks. Any sink can be specified so long as the outer rim dimension plus the sink cutout’s 1/8” [6mm] bevel fit into the DrainTop sink area. Double DropIns require a 1” [25mm] worksurface strip between the two installed sinks.
Cutaway - Front View w/DropIn Sink
Colors Options
Specify any of LabTops colors including Black Onyx, Platinum Gray, Pewter, Pearl, Pacific Blue and Forest Green. Many additional custom colors can be created on a special order basis.
Classic DrainTop Configurations
DrainTop Configurations
Center sink DrainTops with dual drainboards and single drainboard units with sinks offset to the left or right are available.
Dual Drain Board DrainTops Style No.
Sink Location
451 450 457 456
Center Center Center Center
Exterior Dimensions (in)
Sink Area Dimensions (in)
Exterior Dimensions (mm)
Sink Area Dimensions (mm)
Length
Width
Length
Width
Length
Width
Length
Width
54 60 66 72
26-30 26-30 27.5-32 27.5-32
30 30 30 38
18 18 18 20
1372 1524 1676 1829
660-76 660-762 699-813 699-813
762 762 762 965
457 457 457 508
Single Drain Board DrainTops Style No.
Sink Location
454 455
Right Left
Exterior Dimensions (in)
Sink Area Dimensions (in)
Exterior Dimensions (mm)
Sink Area Dimensions (mm)
Length
Width
Length
Width
Length
Width
Length
Width
60 60
26 - 30 26 - 30
38 38
20 20
1524 1524
660-762 660-762
965 965
508 508
C 2004 Laboratory Tops, Inc. All rights reserved.