Industry Insight with John Yoswick
—John Yoswick is a freelance writer based in Portland, Oregon who has been writing about the automotive industry since 1988. He is the editor of the weekly CRASH Network (for a free 4-week trial subscription, visit www.CrashNetwork.com). Contact him by email at jyoswick@SpiritOne.com.
Automakers: Collision Repairers Must Ensure ADAS Calibration Procedures Are Followed
Shop Showcase
The importance of proper ADAS cal- mental?” Kaboos said the Honda training ibrations was a key focus as the Society of Collision Repair Specialists center in Illinois drove a new Civic at with Ed Attanasio (SCRS) brought collision repairers the NHTSA target used to test emerand automakers together at an event gency auto-braking, and the system in Las Vegas during the SEMA Show. worked 10 times in a row, stopping Scott Kaboos, assistant man- the vehicle three or four feet from the ager of collision repair training and target as designed. technology for American Honda, told those attending with the OEM Collision Ed Attanasio Repair Technology Summit that automakers call for many calibrations to be done on a level floor with good reason. “We did a little test,” Kaboos said, noting Honda’s service information says there can be no more with Ed Attanasio than 1 degree of pitch or slope to the Scott Kaboos of American Honda said testing floor when performing calibrations. at the automaker’s training center demonstrat“Traveling around to a lot of our dealed the need to perform ADAS calibrations on a erships, we found that most of their level floor when called for in the procedures floors do not meet that requirement. So we started asking How “So then we took that same car withourselves: Ed Attanasio important is this? Is this really detri- and put the rear wheels in our drain
Social Media for Shops
SEMA Show Goes On
in our wash bay at our training center,” Kaboos said. “We calculated the slope on that, and found that the car was sitting at a 1.6 degree incline. We re-aimed the radar, using the factory specifications and tools. When we were done, the scan tool said aiming was complete. There were no codes. We test drove the car around the block. It gave us no indication there was anything wrong with the car. There were no lights on the dash.” But then the vehicle was driven at the same NHTSA target. “We had very different results,” Kaboos said. “It honestly blew through that target at 20 miles an hour like it wasn’t even there. The light on the dash didn’t blink. It didn’t beep at us. It just punted that target. That was a big eye-opener to us on the training side as to how important that one little line in the service information is: do this on a flat floor.”
Media and Publicity for Shops Shop Strategies with Stacey Phillips
Body Shops Giving Back with Stacey Phillips
Tips for Busy Body Shops
Kaboos said the other noted requirements—proper air in the tires, a full tank of gas—are also important. “Anything that changes the ride height or ride angle of the car is going to throw off all the geometry,” he said. “You’ve got to pay attention to all of that.” Subaru of America’s Ted Hicks said during the same SCRS session that complete repair of the underlying metal where an ADAS camera or radar is attached is also critical. “I asked a panel of technicians in Dallas: what’s the single biggest problem you’re having with calibrations of blind-spot monitoring radar units and the EyeSight cameras that come from body shops after a repair,” said Hicks, a regional technical training manager for the automaker. “They said that the panel that the camera or unit mounts to has got to be exactly correct. If the sheet metal behind it is bent, the radar
ventory Largest In Lincoln • d r o F f o Parts • Mercury
ade County D im ia M In
1200 W. 49 Street, Hialeah, FL 33012
with Stacey Phillips
My SEMA
DIRECT: 305-822-8338 FAX: 305-825-3018 AVALLE@GUSMACHADOFORD.COM
with Stacey Phillips
• OE COLLISION PARTS, MECHANICAL REPAIRS AND HEAVY REPAIRS PARTS • SPECIAL PRICING FOR COMPETITIVE COLLISION AND MOTORCRAFT PARTS • EXPERTShop COUNTER Strategies LOOK-UP WITH MASTER CERTIFIED COUNTERMAN with Victoria Antonelli
34 MARCH 2022 AUTOBODY NEWS / autobodynews.com
HOURS: Monday - Friday 8 am - 7 pm Saturday 7 am - 4 pm
