Interchangeable Heavy-Duty Cleaning Wands for Radiators and Other HardTo-Reach Places. Fast and Easy Cleaning Wands for Use with Water or Air.
Features
• Air Fitting for Radiator Genie
• Handle for Radiator Genie Pro
• Short Tube Assembly
• Long Tube Assembly
• Graphical Hand-Held Tester w/Thermal
all the functions complicated, timeconsuming manufacturer scan tools have to perform the same function but in a fraction of the time. On average the total time required by the technician reset a system is 30 seconds.
Visit www.associatedequip.com for full specifications
oil, chemical and abrasion resistant
• cULus Listed cords remain flexible down to -40˚ F
Both Headlamps Feature:
• 35 powerful LEDs that deliver 1000 lumens of ultra bright light
• 3400 mAh X-TEND lithium ion USB-C rechargeable battery-up to 28 hours of light on low setting and features 5 light modes:
medium, low, red & pulse
• Weatherproof rating of IPX5
• Perfect for professional tradesmen and outdoor activities
The Wedge® is a compact, high-performance EDC light designed for clean pocket carry. It’s outfitted with an intuitive rotating thumb switch that provides tactile control over the constant-on and THRO® (Temporarily Heightened Regulated Output) modes.
• 16 ft. power cord remains flexible in cold weather
• IP67 rated for dust and water resistance
• Foldable stand extends from 34” to 72”
• CSA outdoor certificate
• High quality sound from built-in 5W wireless speaker
• Heavy-duty clamp features (2) strong magnets in base
• Digital battery and lumen setting indicator screen
• Memory function records brightness settings after 5 seconds, and that setting is recalled the next time the device is activated
• COB LED bulb delivers variable brightness of 100 to 1000 lumens
• Lithium-ion rechargeable battery for longer life and consistent power
• Includes USB-C charging cord and 5V, 3.5A AC charger
• Wirelessly stream music from your phone, tablet or any other BT-enabled device Specifications:
• Variable Brightness Floodlight: 100–1000 lumens
• Runtimes: Up to 15 hours
• Battery: 3.7V, 4400mAh lithium-ion battery
• Human Body Sensor - 360˚ microwave radar motion sensor that automatically activates the light when a human body is within 10-15 ft. and turns off when out of range. Saves battery and life-cycle.
• 40” light bar provides 2000 lumens of bright light for maximum area illumination
• UL/cUL listed 8.4V, 2.2 Amp charger with 25 ft. 18/2 SJTOW cord
• 7.4V, 5,200mAh Li-ion battery
• Run Time: up to 2 hours (high), up to 4 hours (low)
• Hooks extend 55” to 83”
• 40” light bar provides 2000 lumens of bright light for maximum area illumination
• UL/cUL listed 8.4V, 2.2 Amp charger with 25 ft. 18/2 SJTOW cord
• 7.4V, 5,200mAh Li-ion battery
• Run Time: up to 2 hours (high), up to 4 hours (low)
• Base swivels 180˚ & is designed to hang from built-in hook or magnets
• Super-bright COB LED bulb delivers step-less dimming from 100/1000 lumens
• Lithium-ion rechargeable battery for longer life & consistent power
• Fast charging: up to 90% of battery capacity after 2 hour charge
• IP65 rated for dust and water resistance
• IK07 rated for mechanical impact protection
• Includes USB-C charging cord and 2A AC charger
Specifications:
• Size: 3.74” W x 1.69” D x 2.91” H • Step-less Dimming: 100-1000 lumens
• Runtime: Up to 12 hours • Battery: 3.6V 4500mAh Lithium-ion battery
• Impact-resistant, lightweight aluminum housing resists rust and corrosion
• Automatic shut-off and overcharging protection for optimal battery life
• Includes USB Type-C charging cord
• SOS signal mode
Specifications:
• Brightness: 60 lumens
• Run Time: 1 hour
• Battery: 3.7V, 180mAh Li-poly rechargeable
• Length: 2”
• Heavy-duty die cast yellow powder coated aluminum housing for high visibility and excellent corrosion resistance
• 16 ft. 18/3 SJTOW oil-resistant power cord remains flexible in cold weather
• IP67 rated for dust and water resistance
• CSA outdoor certificate
• Hooks extend 55” to 83”
• Super-bright 1500 lumen SMD LED bulbs
• 25 ft. 18/2 SJTOW cord
• Hooks extend 47” to 75”
• 2,000 constant lumen LEDs deliver wider and brighter lighting areas
Covers all major model platforms, domestic and foreign, 1988 to present. Redesigned fuel line tee accommodates 3/8”,1/4” and 5/16” hose sizes. A longer tee adapter to cut test hoses for easier connections. Molded storage case. Gauge assembly disconnects from test hose and valve assembly for easier storage and improved gauge protection.
• Includes (10) noid lights plus 4 ft. extension for easy viewing
• Quickly and easily tests electronic fuel injection systems on: GM TBI; GM ‘87 - present; GM ‘82-’91; Bosch PFI; Ford TBI; GM PFI; Geo TBI; GM SCPI
BASIC FUEL INJECTION PRESSURE TESTER
Tests most systems except Bosch CIS and GM TBI; 2-1/2” dual scale gauge reads 0–100 psi or 0–7 BAR; includes the necessary adapters, banjo bolts, and 16” gauge hose with quick coupler and adapter guide book
LIS-32900 Heavy-Duty Circuit Tester/Jumper
removed to test hardto-reach places. Operates on replaceable long-life “N” or “LR-1” size alkaline batteries (included).
New coil cord design for ease of use. Acetate handle, coiled lead wire. Easily checks 6 and 12V systems. New full size comfortable acetate handle lights up when circuit is good. Leads remain flexible in low temperatures. Ground lead stretches up to 10 ft. $12.95
MASTER FUEL INJECTION PRESSURE
Tests both foreign and domestic fuel injection systems; includes late model GM, Chrysler and European applications; large 3-1/2” gauge with dual reading of 0–145 psi and 0–1000 kPa; allows checking for sufficient fuel flow; low pressure 2-1/2” gauge
Tests American Motors, Bosch, AFC, MPC European and Japanese (except CIS); basic fuel injection tester includes large and small Schrader adapters; M6-1.00 O-ring
and
DELUXE VACUUM/ FUEL PUMP TEST KIT
2 ft. of high quality hose, (3) fittings to test domestic and foreign cars and trucks with gas engines; hookon 3-1/2” compound gauge has a multi-color dual scale dial with ranges from 0–10 psi, 0–0.7kg/cm and 0–28inHg/0–70cmHg vacuum
FUEL INJECTION PRESSURE TESTER WITH SCHRADER ADAPTERS
Tests all cars with standard or small Schrader valves; 3-1/2” gauge has a dual scale dial with ranges from 0–100 psi and 0–7 BAR; quick coupler connection at end of gauge hose
PRESSURIZED INDUCTION TOOL KIT
200-1145 Pressurized Induction Tool Features:
• Helps you perform an effective induction service on direct or conventional fuel injected engines
• Chemicals NOT included with tool and must be purchased separately
Visit www.motorvac.com for more information
FUEL INJECTION CANISTER CLEANER
Centrally mounted chain and S-hook provide better balance during cleaning process; stainless steel braided Teflon hose; reduces potential damage by separating the gauges and manifold from the canister during filling; will restore the original spray pattern, giving improved performance, fuel economy and emissions test.
3 WAY EXHAUST BACK PRESSURE KIT
• Test oxygen sensor, exhaust pipes and injection system
• Gauge has (2) multi-colored bands; idle and 2500 rpm, with pressure shown in psi and BAR
• 6 ft. hose
DIESEL SYSTEM TESTERS PRESSURE TESTERS
HD GLOBAL DIESEL COMPRESSION TEST SET
2-1/2” easy-to-read gauge; adapters for Cummins, Bedford, Case, Caterpillar®, John Deere®, Fiat Allis, Ford Tractor, GMC, Hino Trucks™, International and Navistar, Isuzu, Mack, Massey-Ferguson, Mercedes, Mitsubishi-Fuso, Onan, Scania, Volvo, Wisconsin and others.
LIGHT TRUCK COMPRESSION KIT
(12) Compression Test Adapters included for the following applications: GM Diesel 4.3L, 5.7L, 6.2L, 6.5L, 6.6L; Cummins/Dodge 5.9L 12V & 24V; Ford/ Navistar 7.3L, 6.0L, 6.4L, 6.7L, T444E, VT365; Sprinter/ Mercedes 2.7L, 3.0L; VW, Mazda, Nissan-UD, Cat-Perkins, Kubota, Isuzu, Hino, Toyota; other engines utilizing M10 x 1.0, M1- x 1.25, M14 x 1.25, M12 x 1.25 M8 x 1.0
INJECTOR RAIL FUEL LINE CAP SET, 5 PC.
Helps in identification of faulty diesel fuel injectors and used to diagnose engine knock sounds.
Install the cap on the fuel rail in the place of the injection line.
When the cylinder with the failed injector is capped, the rail pressure will rise and the vehicle will start.
Set comes with five different caps.
CUMMINS 5.9L DIESEL FUEL SYSTEM TEST KIT
All adapters necessary for testing on Cummins Series B and ISB engines (including Dodge Ram). Adapters are individually labeled for easy identification.
FORD POWER STROKE DIESEL FUEL SYSTEM TEST KIT
For diesel fuel pressure testing on Ford Power Stroke engines 1994 to present. Includes a 100 psi gauge, a bleed off valve hose assembly, and all the adapters necessary to pressure test the fuel system on Power Stroke engines.
GM 6.6L DURAMAX DIESEL FUEL SYSTEM TEST KIT
For diesel fuel pressure and vacuum testing on GM 6.6L Duramax engines. Gauge assembly with 6 ft. hose and quick coupler. 3-1/2” gauge reads 30 in Hg to 15 psi.
BASIC DIESEL FUEL PRESSURE TEST KIT
Test Kit is used to test fuel pressure between the lift pump and the injection pump on diesel engines, and Can be used to test most diesel engines from single cylinder to V32 models. Includes: 100 PSI gauge assembly with 4-ft. hose, pressure relief valve 6-ft. clear PVC tube, 5 banjo bolt adapters ranging from 8mm to 14mm, 1 repair kit.
COMPUCHEK TESTER
Used to check fuel system pressure on diesel engines with Compuchek test ports. Fits Compuchek test ports on the fuel system of Cummins diesel engines as well as other diesel engines that have been outfitted with the Compuchek test ports. Consists of a hose assembly with a female Compuchek fitting on one end and a 3-1/2”, 300 psi gauge on the other.
QUICK CHANGE AUTOMATIC TRANSMISSION AND ENGINE OIL PRESSURE TESTER
• Set of (21) adapters: (11) aluminum Metric,(7) brass NPT and (3) steel SAE
• 3-1/2” gauge has dual scale with ranges from 0–400 psi and 0–28 BAR
• Quick coupler connection on gauge assembly for fast, easy changing of gauge to the hose assembly
• 6 ft. hose for easy gauge viewing and the ability to test the vehicle from the driver’s seat
• 2-1/2” gauge has dual scale dial with ranges from 0–100 psi and 0–7 BAR; hook on gauge allows technician to hang gauge and hose assembly out of harms way
• Custom blow molded case
AUTOMATIC TRANSMISSION AND ENGINE OIL PRESSURE TESTER
• Tests major model domestic and foreign cars and light trucks
• More accurate than dashboard oil pressure gauges
• 6 ft. of nitrile (oil proof) hose to make testing easier
• Standard and metric fittings
• Checks oil pressure in automatic transmissions and gasoline engines
• 2-1/2” gauge has a dual scale dial with ranges from 0–300 psi and 0–21 BAR
COMPRESSION TESTERS
UNIVERSAL COMPRESSION TESTER
Gas engine compression testing on domestic and foreign vehicles; screw-in adapters with O-rings; incudes 14mm and 18mm short-solid, 14mm and 18mm long-flex and 14mm long-reach adapters; long flex 12” hose and side release valve; 2-1/2” gauge has dual scale dial with ranges from 0–300 psi and 0–21 BAR
COMPRESSION TEST
KIT
FOR GASOLINE ENGINES
Test all major model vehicle platforms, domestic and foreign with gasoline engines, including mini engines. 2-1/2” gauge has dual scale with ranges from 0-300 psi and 0-21 BAR. Includes 24” hose assembly w/ quick coupler; M14 hose adapter w/ short thread; small engine tester; M14 hose adapter w/ long thread; M12 x M16 hose adapter; M10 adapter w/ short thread; M14 adapter extension
POWER STEERING
AND RACK TESTER
• Handy diagnostic tool for rack problems
• Takes the guesswork out of power steering analysis quickly and accurately, by detecting defective power steering pumps and gears and kinked or clogged lines
• Quickly points out if trouble is in front suspension or steering linkage
• Includes most adapters needed to test domestic cars and light trucks and some imports
• Dual 2-1/2” easy-to-read gauge records
PROFESSIONAL COMPRESSION TEST KIT
2-3/4” gauge with high impact lens, rubber boot, (4) scales of measure (psi, kg/cm2, BAR, kPa), 10” long hose and quick release coupler; 14mm short-thread adapter with 6-1/2” and 12” hoses; 14mm long-thread adapter with 12” hose; 18mm short-thread adapter with 12” hose; 14mm short-thread x 18mm long-thread adapter; 10mm thread small engine adapter; field service kit; quick release air hold adapter; 12mm thread small engine adapter
CYLINDER LEAKAGE TESTER
Use with most standard compression test adapters; easy-to-read pressure gauge has a dual scale dial with ranges from 1–100 psi and 0–7 BAR with a gauge boot for added protection; 2 gauge design allows for monitoring of input air line pressure to ensure accurate testing; uses shop air to determine leakage source
INFRARED THERMOMETERS
•
• Extensive make, model, engine, and system coverage - for North American commercial vehicles / heavy duty trucks
OBD-II Coverage (1996-present), US, European & Asian vehicles, supports all protocols including CAN. Reads live data stream, retrieves vehicle VIN, CIN & CVN, clears codes, turns off MIL & resets monitors.
Visit https://www.esitest.com/ for full specifications
Features dual-mode leak detection: test for leaks with or without smoke at the push of a button. Pressure and vacuum leak diagnostics with instant smoke vapor with UV enhanced dye. Test Evaporative Emissions (EVAP) systems and more. Includes a 4.1 oz. bottle of smoke solution.
• Guns have stainless steel needle and nozzle sets
• Knob for spray pattern adjustment
• Operating pressures of 15-45 psi
• Air inlet: 1/4”
• Air consumption: 7.0 to 9.0 CFM
• Meets EPA NESHAP 6H rules for compliance
• 2 pc. construction w/ exclusive air valve design
• Fully adjustable wide fan pattern control
• Maximum pattern at 8” distance: 11”
• Includes 1 qt. drip less cup
1L SOLVENT SPRAY BOTTLE
• Durable, high density polyethylene material
• Viton® FKM O-rings offer outstanding resistance to solvents including acid based solutions
SPRAY GUN SET
•
• Suitable
• Ultra high flow nozzles provide superb versatility across the major range of viscosities
• Applications: Primer, Basecoat, Clearcoat
application
•
•
500 LUMEN RECHARGEABLE PAINT GUN LIGHT
• Versatile color temperature settings ranging from 2700K to 6500K
• CRI rating of > Ra96 for accurate and vibrant color representation
• Fits paint guns with OD nozzle sizes ranging from 27mm to 41mm
• Optional motion-sensing mode for easy ON/OFF control
• Constant current technology for consistent lumen output throughout battery charge cycle
• Memory function remembers preferred settings
• Chemical-resistant housing materials for durability
• Flexible hinge for easy fitment onto different paint gun brands and styles
• USB Power Delivery fast-charging technology for quick and efficient charging
• IP65 rated for dust and water resistance, IK07 rated for mechanical impact protection
• Automatic shut-off and overcharge protection for battery life
• Flashing low-battery warning
• Red and green charging indicator LEDs
• Includes 5 clear polycarbonate lens covers and USB type-C charging cord (ATD-80465)
DURABLE BRIGHT WHITE POWDER-COAT FINISH INSIDE AND OUT OPTIMAL LIGHTING COVERAGE WITH “HIP PANEL” DESIGN
HEAVY-DUTY, PRECISION PUNCHED 18
5/16” BOLT AND LOCK NUT ASSEMBLY
• Allows one person to lift truck bed using an engine hoist
• Adjustable bracket design to accommodate various bed sizes
• Lifter bracket adjusts quickly and easily to evenly distribute the bed weight
• Support pad dimensions: 6.3” L x 1.5” W x .9” H
• Powder coat finish
• For use with pickup boxes and other large parts
• Powder coated steel
• 2 pc. Locking Ring for safe storage
• (6) 4” swivel casters, (4) locking
• Maximum load capacity 800 lbs.
• 4’ W x 5’ L x 3’ H
• Folds for convient storage
• Powder coated steel construction
- durable, corrosion resistant
• Support Size: 30” L x 24” W
• Perfect for paint booths, mixing rooms, prep stations, etc.
Designed to hold (5)
• Magnetic design for portability with (12) powerful magnets • Heavy-Duty powder coated steel construction • Paint Gun Not Included
• Rubber padded support tubes (Work stand shown is not included)
1000 LBS. CAPACITY WORK STAND
• Steel Tubing Diameter: 1.25”
• Steel Tubing Thickness: 0.08”
Both ATD Work Stands Feature:
• Lightweight construction with steel tubing with 1/2” foam padding wrapped around and down the top of th frame
• Leg Tube Length: 30.7”
• Bent Tube Length: 40.35”
500 LBS. CAPACITY WORK STAND
• Steel Tubing Diameter: 1.10”
• Steel Tubing Thickness: 0.05”
• Working Height: 22.8”–37”
• Low and high heat settings with a temperature range from 158˚F to 1,112˚F
• Perfect for curing adhesives, removing decals/stripes, drying body fillers/paint, shrink tubing, etc.
• Durable die-cast metal housing
• Adjustable, removable stand for cool down or hands-free use
• Temperature Range: 158˚F to 1,112˚F
• Dual heat settings (230W or 150W) • cUL Listed
(2) general purpose soldering tips
15 gm lead-free solder
(1) soldering aid tool
(1) flux brush
(1) cutting tip
1/4” AIR HYDRAULIC RIVET TOOL
• Supplied with 3/32”, 5/32”, 3/16” and 1/4” standard nosepieces, service tools, swivel inlet, air coupler and a mandrel collection bottle
• Recommended air line pressure is 85–95 psi
• Weight: 6.2 lbs.
• Set blind rivets from 1/8” dia. in all alloys, up to 3/16”
• Standard 1/8”, 5/32”, and 3/16” nosepieces, a service wrench, swivel inlet air coupler and a mandrel collection bottle
• Sets up to 3/16” rivets
• Includes (4) nosepieces and sample rivets
THREAD SETTER
Includes: 39300 Thread-Setter Tool; (1 ea.) 8-32, 10-32 and 1/420 mandrels and nosepieces; (52) assorted Klik Poly-Nuts: (12 ea.) 47425, 47435 and 47445; (16) 47455; wrench
RIVET TOOL
Known and trusted for durability, quality and performance, this Marson rivet tool is often copied but never equaled. The Marson 39000 sets up to 3/16” steel rivets and comes with four mounted nosepieces (3/32”, 1/8”, 5/32”, and 3/16”) and a service wrench.
1/4” RIGHT ANGLE DIE GRINDER WITH FREE 1/4” MINI DIE GRINDER
Set Includes: 1/4” RIGHT ANGLE DIE GRINDER
• No Load Speed: 20000 rpm
• 1/4” air inlet
• Recommended Air Pressure: 90 psi
• Average Air Consumption: 2.2 CFM
1/4” MINI DIE GRINDER
• No Load Speed: 25000 rpm
• 1/4” air inlet
• Recommended Air Pressure: 90 psi
• Average Air Consumption: 3 CFM
MINI POLISHER KIT
• 2500 rpm, 1/4 Hp motor
• Rubber molded pistol grip
• Adjustable power regulator
• Progressive throttle
Soft-start feature
• Spindle Thread: 5/8”-11
• Silent handle exhaust Includes: CP7201 mini polisher; (1) 3” backing pad, (2) 3.5” foam compounding pads (white/yellow), (1) 3.5” wool buffing pad and spindle wrench packed in a heavy-duty case
7” VARIABLE SPEED POLISHER KIT
Specifications:
• No Load Speed (variable speed): 0 - 3,200 RPM
• Includes pad alignment/centering sleeve
• Sanding Disc: 7”
• Wool Bonnet: 7”
• Amps: 10
• Spindle Thread: 5/8” - 11 UNC
• Overall Length: 18-1/2” www.makitatools.com
1/4” SURFACE PREP KIT
2” Type III Disc Holder - ATD-6601
• Type III fastener features a roll-on/roll-off style
• Medium-density, rubber backup pad ideal for contour work, feathering and edging into corners
• Recommended for plastics and stainless steel for the chemical, food, auto, aircraft and aerospace industries
Kit Includes: 2” and 3” backing pads, sanding, and polishing disks, 1/4” and 6mm collets, 2 wrenches and a molded case
Specifications:
• Amps: 12.0
Spindle Lock: Yes • Max Watts Out:
ABRASIVE BLASTERS
•
•
• Includes 8 ft. hose, shut-off valve, pressure gauge, filling funnel, water trap and canvas hood
• Requires 6–25 CFM air supply and 60–125 psi working pressure
• Deadman control valve for the ultimate in safety and control
• 6” wheels and convenient handle for easy mobility
• Heavy-duty, all-steel construction blast pot
• Suitable for 60 to 100 grit abrasive
20 TON BODY & FRAME REPAIR KIT
BENCH TOP STEEL BLAST CABINET
• 21” x 17” transparent opening for easy loading and viewing
• Includes work light, safety valve, sealed gloves and blast gun
• Use with glass beads, silica sand and aluminum oxide
• Requires shop air compressor delivery of 100 psi @ 5 CFM
• Work Area: 22” W x 18” D x 11” H
• Overall Size: 23” W x 19” D x 19” H
• Contains all the tools necessary for pushing, spreading, and pressing of vehicle body panels, parts and assemblies
• Auto air bleed pump eliminates the need to bleed system prior to use
• Dual piston pump delivers faster lifting speeds saving time and money
• Double braided hydraulic hose provides protection against abrasion and heavy wear
• Attachments are interchangeable with other body and frame kits
ATD Body Repair Kit Features:
• Designed for pushing, spreading and pressing of vehicle body panels
• Heavy-duty case allows easy storage and transport for use in shop or on the road
• ATD-5810A features a DOUBLE SPEED auto bleeding pump with pressure gauge
• ATD-5800A features a standard auto bleeding pump with pressure gauge
• Both sets meet or exceed ASME/PASE 2019 Standards Ram Capacity: 10 Ton Pump Capacity: 10,000 psi
Ram - Closed Height: 12.7”
Ram -
RIVET TOOLS
5850 Features:
5855 Features: • Includes (8) mandrels/nosepieces in the following sizes: M4, M5, M6, M8, M10, 1/4”, 5/16”, 3/8”
•
• Includes (4) nosepieces: 3/32”, 1/8”, 5/32” and 3/16”
• For use with 3/32”, 1/8”, 5/32” and 3/16” aluminum and steel rivets
• Pulling Force: 2,646 lbs.
and
5851 Features:
• Includes (4) nosepieces: 1/8” 5/32”, 3/16” and 1/4” • Use with 1/8”, 5/32, 3/16” and 1/4”
12”
NUT/THREAD HAND RIVETER KIT
Set Includes: 12” heavy-duty nut/thread rivet tool with double compound hinges for maximum leverage and smooth operation; (1 ea.) metric mandrel/nosepieces in M5, M6 and M8; (1 ea.) SAE mandrel/nosepiece in 10-24, 1/4”-20 and 5/16”-18; (10 ea.) of the following rivet nuts in M5, M6, M8, 10-24, 1/4”-20 and 5/16”-18; wrench
HEAVY-DUTY 1/4” STUBBY HAND RIVETER
• 3 piece Chrome Moly steel jaws provide long lasting tool life
• Collection bottle for safety and ease of disposal
• Includes (5) Nosepieces: 1/8”, 5/32”, 3/16”, 7/32” and 1/4”
• Length: 13”
HEAVY-DUTY 1/4” HAND RIVETER
• 2-1/4” nose and heavy-duty metal construction
• Extra-long handles for excellent leverage
• (5) nosepieces to set 1/8, 5/32”, 3/16”, 7/32” and 1/4” steel and aluminum rivets
• Overall Length: 20-3/4”
Set
•
EXHAUST TUBING
• 3-in-1 tool combines coolant, battery, and DEF scales all in one
• Reads both Ethylene and Propylene Glycol based coolants Kit Includes:
• Fluid dropper • Screwdriver
• Cleaning cloth • Molded case
12V
PORTABLE 12V DC 1/5 Hp, 3/4” NPT INLET NO NOZZLE
12V DC, 10 GPM, standard duty, explosion proof with carrying handle. Designed for diesel fuel. Includes pump, 6 ft. 12 Ga. 2-wire battery cable with clips and 30 Amp fuse. CE, 1 year warranty. Made in USA
• Makes transfer of gasoline, kerosenem diesel, or mixed fuels safe and easy
• Complies with OSHA guidelines with ground wire and clamp
• Two-way pump operation for either siphoning or dispensing 1 gal. for every 12 revolutions • Fire screened vent and filler neck combination
8 ft. discharge hose
• Dolly handle for ease of movement
3 wheel mechanical fuel transfer meter kit, 5-20 GPM. Aluminum construction. +/- 1% accuracy rating. Designed for gasoline, diesel, biodiesel up to B20, E15 and kerosene. Includes meter and fittings to mount on 3/4” outlet fuel transfer pumps. UL/cUL, ATEX, CE. Two year warranty. Made in USA
HIGH FLOW ROTARY HAND PUMP
• For use with
diesel fuel, kerosene & light lubrication oils up to SAE 30 weight
• 3:1 discharge - (3) rotor turns for every rotation of the handle
6 ft. delivery hose with metal nozzle • 3 pc. threaded suction tube for use on 15-55 gal. drums
• DO NOT USE WITH: Corrosive liquids, solvents, acids, alkalis etc.
This UL Listed steel gas caddy is rigorously tested for leakaage,
STUD WELDER KITS
The Stinger PLUS (5500) and DELUXE (9000) Stud Welder Kits now include the tab setter adapter and a pack of tabs for faster, more accurate pulls!
C-CLAMPS
HOSE NOZZLES
3-IN-1
• 1/2” ground clearance
• 40” L x 26-3/4” W
• 2” minimum height allows the installer to crawl under the lowest of vehicles
• 3” polyurethane wheels for smooth movement around the shop floor
• Perfect for the mechanic, paint and body or detail shop
• Quickly and easily converts from low profile creeper, to Z-creeper seat, to L-seat
• Comfortable fully upholstered pad
• (6) Oil and chemical resistant 3” polyurethane wheels
• Powder coated steel frame
Specifications:
• Weight Capacity: 450 lbs.
• Size: 39-7/8” L x 26” W x 4-1/2” H
• Weight: 26 lbs.
resistant casters with full ball bearings • 40” L x 6-1/2” H x 19” W • Capacity 450 lbs.
• Great for getting to the engine from the top of the vehicle
• Allows extended periods of time spent bending over the engine without the effect of painful fatigue
• The height of the Easy-Reach Creeper can be adjusted to allow use on many different types of vehicles
• Constructed of heavy-gauge steel with a powder coat finish to protect from scratching
• 3” swivel casters with (2) locking swivel casters for easy movement
• Deck is padded and covered with heavy vinyl for comfort and durability
• Height adjustable from 47.5” to 70”
• Shipping Dimensions: 51.2” x 24.4” x 6.7”
ABS plastic hooks can be mounted anywhere on the 24”
•
•
•
•
•
•
with gasket for GM, (1 ea.) LG, M and SM adapters with gaskets, (1 ea.) LG, M and SM caps, threaded cap for GM, 5” straight extension, (2) 45˚ elbows, lid.
24mm for Cadillac and some BMW, 27mm for 2003 and later Mercedes1.8L, Smart and some VW; 29mm (11/8”) for Dodge Cummins fuel filter housing; 32mm (1-1/4”) for GM Ecotec, 2.0L, 2.2L and 2.4L four cylinder, some Saturn and Saab; 35/36mm for Ford 6.0L diesel, Mini Cooper, some BMW and Mack Truck
24mm for Cadillac and some BMW, 25mm for Fleetguard filter on motorhomes, buses, and some medium sized trucks with Cummins engine, also some K&N fliters; 27mm for 2003 and later Mercedes1.8L, Smart and some VW; 28mm for 2010–2018 6.7L Dodge Cummins fuel filter canister; 29mm (1-1/8”) for Dodge Cummins fuel filter housing; 32mm (1-1/4”) for GM Ecotec, 2.0L, 2.2L and 2.4L four cylinder, some Saturn and Saab; 35/36mm for Ford 6.0L diesel, Mini Cooper, some BMW and Mack Truck
Includes: Soft grip, stubby reversible ratcheting screwdriver handle; magnetic bit holder; socket bit holder; (2) Extensions: 1/4” sq. x 1/4” hex x 1” and 1/4” sq. x 1/4” hex x 2”; wing nut driver; Phillips: #0 x 1, #1 x 1, #2 x 5 and #3 x 1; Pozi: #0 x 1 , #1 x 1, #2 x 5 and #3 x 1; Clutch: #1, #2 and #3; Spline: M5, M6 and M8; 6 Roto-Set, 8 Roto-Set and 10 Roto-Set; Spanner: 4, 6, 8 and 10; Square Recess: #0, #1, #2 and #3; Tri-Wing: #1, #2, #3 and #4; Tamperproof Star: T8, T10, T15, T20, T25, T30 and T40; Star: T8, T10, T15, T20, T25, T30 and T40; Slotted: 3, 4, 4.5, 6 and 7mm; Tamperproof Metric Hex: 2, 2.5, 3, 4, 5 and 6mm; Metric Hex: 2, 2.5, 3, 4, 5 and 6mm; Tamperproof SAE Hex: 5/16”, 3/32”, 7/64”, 1/8”, 9/64 and 5/32”; SAE Hex: 5/64”, 3/32”, 7/64”, 1/8”, 9/64”, 5/32”, 3/16”, 7/32” and 1/4”; molded case
Power Bit Set Set Includes: (3) Square Drive Adapters: 1/4”, 3/8”, 1/2”; Magnetic Bit Socket; Swivel Head Quick Release; Nut Setters: 5/32”, 3/16”, 7/32”, 1/4”, 9/32”, 5/16”,11/32”, 3/8”, 7/16”, 1/2” SAE; 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12 METRIC; 1” Long Bits: (4) Phillips 0, 1, 2, 3; (4) Pozi Drive (PZ): 0, 1, 2, 3; (4) Hex: 3, 4, 5, 6mm; (4) Slotted : 5-6, 6-8, 8-10, 10-12; (4) Tamper Proof Torx: 15, 20, 25, 30
Slotted, Square
and
$19.95
$24.95
ATD-551 50-Pc. Torsion Impact Bit Set
106-Pc. 6 Point 1/4” and 3/8” Standard and Deep Master Socket Set 1/4” Drive: (9) Standard SAE Sockets: 3/16”–1/2”; (9) Deep SAE Sockets: 3/16”–1/2”; (8) Standard Metric Sockets: 4–12mm; 45-tooth, 1/4” Quick Release Ratchet; (2) Wobble Extensions: 2” and 6”; Spinner Handle; 1/4” F x 3/8” M Adapter; Universal Joint; Bit Coupler; 5” Flex Handle. 3/8” Drive: Universal Joint; 8” Flex Handle; 3/8” F x 1/4” M Adapter; (9) Deep SAE Sockets; (9) Standard SAE Sockets: 3/8”–7/8”; (3) Wobble Extensions: 3”, 6” and 10”; (12) Deep Metric Sockets: 8–19mm, 45-tooth, 3/8” Quick Release Ratchet;
IA800 Optical ADAS Positioning System Wheel Alignment
Pre-Check #IA800*
• Intelligent optical positioning system for Autel Standard Calibration Frame
• Includes 6 hi-res cameras, wheel clamps, targets, and power supply
• Complete ADAS calibration frame positioning in as little as 1 minute
• Do away with mechanical measurements
• Significantly reduce setup time and increase positioning accuracy
• Ideal for collision repair, glass replacement, and repair shops
• Fast, accurate, and easy
• Check alignment tolerances prior to calibration
CALL US FOR PRICING
*Part # will vary depending on additional accessory packages IA800LDW, IA800LDWT, IA800AS, IA800AST
AUTEL DIAGNOSTIC TABLETS
• Enhanced AutoVIN and ScanVIN for the most accurate vehicle identification
• Dynamic color-coded CAN bus & Module Topology
• Simplified security gateway access
• Combines vehicle communication and measurement functions
• Built-in preset guided tests for faster operation
MaxiSYS MS919 Advanced Diagnostic Tablet #MS919
• 9.7” heavy duty touchscreen
CALL US FOR PRICING
MaxiSYS MSUltra ADAS Advanced Diagnostic Service Tablet #MSULTRA
• 12.7” heavy duty touchscreen
• View multiple functions at once
• Docking station included
CALL US FOR PRICING
BOSCH ADS DIAGNOSTIC SCAN TOOLS
• Complete Domestic/Asian/Euro coverage for vehicles as far back as 1976
• Approved by FCA to unlock Secure Gateway (SGW) protected vehicle
• Over 14 hours of battery runtime with over weeks of standby
• Fastest performance with Quick-Scan, Android 9 OS or higher, latest hardware/software technology
• Wireless J2534-compliant VCI included
• Easy to use and technician approved user interface
• Lifetime Warranty
ADS 525X Diagnostic Scan Tool #3945
• Ultra crisp 8-inch vibrant, high definition display with full widescreen viewing
CALL US FOR PRICING
ADS 625X Diagnostic Scan Tool #3970
• Ultra crisp 10 inch vibrant, high definition display with full widescreen viewing
• Multipurpose docking station charges tablet, provides AC power to VCI to access repair information without being connected to vehicle and seamless wireless updates
CALL US FOR PRICING
WASTE OIL FURNACE KITS
140,000 BTU Waste Oil Furnace* #1140101
$7,852
200,000 BTU Waste Oil Furnace* #1200101
$9,136
350,000 BTU Waste Oil Furnace* #1350101
$13,586
*All furnaces include SteadyFlo Fuel Pump, Squirrel Cage Blower, Integrated Air Compressor, Barometric Damper, Pre-Heater, Hour Meter and Filter Head Assembly. Draft gauge, fuel kit, tank mount kit and fuel delivery are ordered separately.
HOSE REELS
3/8" x 50' Premium Duty Hose Reel
#7650-OLP
• Individually powder-coated steel components
• Low-pressure 3/8" x 50' PVC hose included; hose is for air or water service only
• Guide arm adjusts to seven positions $509
3/8" x 50' REELSAFE® Controlled Return Hose Reel
#RS7650-OLP
The new REELSAFE® Series RS7000 controlled return hose reel is an expansion of the rugged design that set the industry standard. With safety at the forefront, REELSAFE® pays out like a traditional reel, though is specifically engineered to retract the hose at an average walking speed. The centrifugal clutch, integral to the reel base, greatly decelerates the hose retraction speed by up to 83% vs. a Series 7000 reel.
Transair’s modular aluminum pipe delivers superior performance for compressed air, vacuum and inert gas applications. The aluminum construction prevents corrosion build-up and deterioration of the pipe over time. All Transair aluminum pipes leave the factory with a QUALICOAT certified coating for protection against environmental effects. Transair will not add additional contaminates into a compressed air system. The quality of air leaving the compressor room will remain unchanged in a Transair system.
With Transair, there is no need to paint the piping to indicate the media being conveyed. Transair comes in three standard colors: blue for compressed air, gray for vacuum, and green for industrial/inert gasses.
A Transair system can integrate into existing copper and steel compressed air systems without compromising performance, making it ideal for system upgrades or expansions. The lightweight materials, quick connection technology and minimal required tooling allow a Transair system to be installed 4x faster than traditional methods.
CALL US FOR A QUOTE
AIR COMPRESSORS
THE BEST OF BOTH WORLDS
Our hybrid compressors offer the durability and 100% duty cycle of a rotary screw, together with the intermittent demand and energy savings of a piston. Plus the security of a backup.
• Break back style wrenches provide a large break angle, to prevent the possibility of over torquing
• Chrome molybdenum ratchet gear and fully heat-treated handle
• Ideal for noisy and difficult working conditions
• Includes blow molded storage case and instructions
• Knurled handle for non-slip grip
• Fast, accurate, easy to set
• Teardrop ratchet head
• Easy-to-read stamped scale on beam and thimble collar
• Positive lock with spring-loaded pull-down lock ring
• Meets ISO 6789 specifications
• Calibrated on test equipment complying with ASME B107.300-2010 accuracy requirements
• Molded storage case, instructions and calibration certificate
WRENCH
Specifications:
• Drive type: 1/2”, ratcheting
• Range: 50-250 ft.-lbs
• Increments: 5 ft.-lbs.
• Overall Length:
• Length: 18-1/2”
• Comfort grip handle
• Heat
•
•
• Meets
HEAVY-DUTY AUTOMATIC WIRE STRIPPER
Operates both internal and external rings. Heat treated chromium-molybdenum steel. Comfortable insulated vinyl handles. Includes one each: 5-1/2” Bent Pliers w/.038” Tip, 6” Straight Pliers w/.038” Tip, 5-1/2” Bent Pliers w/.047” Tip, 6” Straight Pliers w/.047” Tip, 7-1/2” Bent Pliers w/.070” Tip, 8” Straight Pliers w/.070” Tip, 8-1/2” Bent Pliers w/.090” Tip, 9” Straight Pliers w/.090” Tip, 5” Hook Tool, 5” Pick Tool, case.
$42.95 LNG-1489 26” Snap Ring Pliers Use on GM 5L40, 5L50, 6L45, 6L50, 6L80, & 6L90 and some BMW transmissions to remove large internal snap ring. MADE IN USA $64.95
LNG-3597 6-Pc. Quick Switch Internal/External Snap Ring Pliers Set Internal: 3/8”–2”; External: 1/4”–2”. Includes: 6” Straight w/.030” Tip, 6” Bent 90˚ w/.038” Tip, 6” Straight w/.047” Tip, 6” Bent 90˚ w/.047” Tip, 7-1/2” Straight w/.070” Tip, 7-1/2” Bent 90˚ w/.070” Tip, case.
$89.95
LIS-38700 Spindle Snap Ring Pliers for Ford SD Replace spindle snap rings found on 2007 and newer Ford Super Duty pickups $44.95
LIS-49200
Snap
Heavy-duty pliers construction and larger tips designed for larger snap rings. Includes 10 tip sets in a plastic pouch: .060” Dia. 75˚, .060 Dia. 15˚, .075” Dia. 75˚,.075” Dia. 15˚, .090” Dia. 75˚, .090” Dia. 15˚, .108” Dia. 75˚, .108” Dia. 15˚, .125” Dia. 75˚, .125”
15˚. $39.95 LNG-1421 Quick Switch Pliers with Adjustable Stop and Tip Kit
LNG-1434
LNG-75
Quick Switch Pliers with Tip Kit
Convert between internal and external with a quick flip of a switch. Double-dipped custom grip made of low-temp, high-impact material for comfort and durability. Internal: 1/4” - 1” ; External: 1/8” - 1” . Includes: Straight: .023”, .039” and .047” Tips; Bent 90˚: .039” and .047” Tips.
Convert between internal and external with a quick flip of a switch. Double-dipped custom grip made of low-temp, high-impact material for comfort and durability. Internal: 3/8” - 2” ; External: 1/4” - 2” . Includes: Straight: .039”, .047” and .074” Tips; Bent 90˚: .039” and .047” Tips.
$24.95
$27.95
External: 1-1/2”–4”. Includes: Bent 15˚: .090”, .108” and .120” Tips; Bent 70˚: .090”, .108” and .120” Tips. MADE IN USA $59.95 LNG-1465 3-Pc. Quick Switch Retaining Ring Pliers
Contains one each of the 1421 and 1434 models as well as the 75 model (Internal & External Replaceable Tip Retaining Ring Pliers with Automatic Ratchet Lock). Includes 3 tip kits; one each containing 5 pairs of color-coded, interchangeable tips and hex
COMBINATION RATCHETING WRENCHES
ADJUSTABLE WRENCHES
REVERSIBLE RATCHETING WRENCHES
FLEX HEAD RATCHETING WRENCHES
TOOLS
5-Pc.
Punches: 1/8”, 5/32”, 3/16”, 1/4” and 5/16” $13.95 ATD-760 8-Pc. Punch and Chisel Set Pin: 1/8”, 3/16” and 1/4”; Solid: 1/4”; Center: 3/8”; Cold Chisels: 1/2”, 5/8” & 3/4” $26.95
ATD-714 14-Pc. Punch and Chisel Set Pin: 3/16” x 3/8” x 6”, 1/8” x 3/8” x 5”, 3/32” x 3/8” x 5” and 1/4” x 1/2” x 6”; Center: 1/8” x 3/8” x 5”; Taper: 3/8” x 5/8” x 10”, 5/32” x 1/2” x 9”, 1/8” x 1/2” x 10” and 1/8” x 3/8” x 8-1/2”; Cold Chisels: 1/2”, 5/8”, 7/8” and 1”
ATD-720 20-Pc. Punch and Chisel Set Pin: 3/32”, 1/8”, 5/32”, 3/16” 1/4” and 5/16”; Starter: 1/8”, 5/32”, 3/16”, 1/4” and 5/16”; Center: 1/4”, 3/8” and 1/2”; Flat Chisels: 1/4”, 3/8”, 1/2”, 5/8”, 3/4” & 7/8”
ATD-729 29-Pc. Punch and Chisel Set Pin: 3/32”–3/8”; Starter: 3/32”–5/16”; Cap Chisels: 1/4” and 5/16”; Center Punches: 1/4”–1/2”; Diamond Point Chisel: 5/16” and 3/8”; Half Round Nose Chisel: 5/16”; Flat Chisels: 1/4”–7/8”
MAY-61044 14-Pc. Punch and Chisel Set Center Punch 3/16-5mm x 5”; Cold Chisel 1/4-6mm x 5”; Cold Chisel 1/2-13mm x 6”; Cold Chisel 5/8-22mm x 6-1/2”; Cold Chisel 3/4-19mm x 7; Cold Chisel 3/8-10mm x 5-1/2”; Line-Up Punch 1/8-3mm” x 7 7/8”; Pin Punch 3/32” x 4-1/2”; Pin Punch 1/8” x 4-3/4”; Pin Punch 5/32” x 5”; Pin Punch 3/16” x 5-1/4”; Pin Punch 1/4” x 5-3/4”; Solid Punch 1/8” x 5”; Solid Punch 3/16”
$36.95
$64.70
GREY PNEUMATIC
THE SETS FEATURED ON THIS PAGE COME IN A BLOW MOLDED CASE
The ATD-277 Tap and Die Set includes everything in the ATD-276 Tap and Die Set; #3, #7, #9, #16, #19, #20, #21, #25, #29, #30, #36, #39, #43, letter B, letter F, letter H, letter I, letter J, letter O, letter Q, letter R, letter S, letter U, letter Z, 5/64”, 7/64”, 5/32”, 1/4”, 19/64”, 5/16”, 21/64”, 3/8”, 25/64”, 13/32”, 27/64”, 29/64” high speed drill bits; EX-1, EX-2, EX-3, EX-4, EX-5 spiral flute screw and bolt extractors; molded case
#4-40, #6-32, #8-32,#10-24, #10-32, #12-24 machine screw plug tap and 5/8” hex dies; 1/4”-20, 1/4”-28, 5/16”-18, 5/16”-24, 3/8”-16, 3/8”-24, 7/16-14, 7/16”-20, 1/2”-13,1/2”-20 fractional plug tap and 1” hex dies; M3x0.5, M4x0.7, M4x0.75, M5x0.8, M5x0.9, M6x1 metric plugs taps and 5/8” hex dies; M7x1, M8x1,M8x1.25, M9x1, M9x1.25, M10x1.25, M10x1.5, M11x1.5, M12x1.5, M12x1.75 metric plug taps and 1” hex dies; 1/8”-27 NPT and 18-/8”-28 NPT pipe thread plug taps and 1” hex dies; adjustable die stock for 1” dies; plain die stock for 5/8” dies; adjustable handle tap wrench for taps 1/4”–1/2”; 2-in-1 tap wrench for taps 1/4”–1/2”; t-handle tap wrench for taps #0–1/4”; metric thread pitch gauge; fractional thread pitch gauge; molded case
6 SAE Fine Taps: 1/4”-28, 5/16”-24, 3/8”-24, 7/16”-20, 1/2”20, 9/16”-18
7 Metric
#4-40, #6-32, #8-32, #10-24, #10-32, #12-24; 1/4”-20, 1/4”-28, 5/16”18, 5/16”-24, 3/8”-16, 3/8”-24, 7/16”-14, 7/16”-20, 1/2”-13, 1/2”20; M3x0.5, M4x0.7, M4x0.75, M5x0.8, M5x0.9, M6x1, M7x1, M8x1, M8x1.25, M9x1, M9x1.25, M10x1.25, M10x1.5, M11x1.5, M12x1.5, M12x1.75; 1/8”-27 NPT, 1/8”-28 BSP; adjustable/nonadjustable t-handle tap wrench; adjustable and plain die stock; 2-in-1 tap wrench; 16 leaf metric thread gauge; 18 leaf standard thread gauge; molded case
M3x0.5, M4x0.7, M4x0.75, M5x0.8, M5x0.9, M6x1, M7x1, M8x1,M8x1.25, M9x1, M9x1.25, M10x1.25, M10x1.5, M11x1.5, M12x1.5, M12x1.7; 1/8”-28 BSP; plain die stock; 5/8” hex dies; adjustable die stock for 1” dies; adjustable handle tap wrench for #0–1/2”; t-handle wrench for taps #0–1/4”; 2-in-1 tap wrench for taps 1/4”–1/2”; 18 leaf metric thread pitch gauge; molded case
(10)
(16)
#4-40, #6-32, #8-32,#10-24, #10-32, #12-24 plug tap and 5/8” hex dies; 1/4”-20, 1/4”-28, 5/16”-18, 5/16”24, 3/8”-16, 3/8”-24, 7/16-14, 7/16”-20, 1/2”-13,1/2”-20 plug tap and 1” hex dies; 1/8”-27 NPT pipe thread plug tap and 1” hex die; adjustable die stock for 1” dies; plain die stock for 5/8” hex dies; adjustable handle tap wrench for taps #0–1/2”; t-handle wrench for taps #0–1/4”; 2-in-1 tap wrench for taps 1/4”–1/2”; 18 leaf standard thread pitch gauge; molded case
1/4”-, 1/4”, 7- mm, 7mm, 8- mm (5/16”), 8mm (5/16”), 3/8”-, 3/8”, 10- mm, 10mm, 11- mm (7/16”), 11mm (7/16”), 12-mm, 12mm, 1/2”-, 13- mm (1/2”)
7mm, 8mm (5/16”), 3/8”, 10mm, 11mm (7/16”), 12mm,
TOOL SETS
(6) machine screw taps and (6) dies;
SAE taps and (10) dies;
metric taps and (16) dies; (2) pipe taps and (2) dies; high speed drill bits; spiral screw extractors; adjustable handle tap wrench; 2-in-1 tap wrench; T-handle wrench; pitch gauges; molded case
394001
11119
54113
394002
•
• For use on most domestic and import 2WD and 4WD vehicles
• Use on front or rear disc brakes
• Includes tools and adapters for both right- and left-handed threads
• Use on main brakes and parking brake systems
AIR BRAKE SERVICE TOOL KIT
• Removal tools for slack adjusters and push-rod clevis pins used on brake systems of class 7 and 8 vehicles
• Works on manual and automatic
• Includes 2 slack adjuster pullers and a brake clevis pin press
•
FRONT WHEEL DRIVE BEARING ADAPTER KIT
These front wheel bearing adapters replace wheel bearings while keeping the steering knuckle and strut assembly intact on the vehicle, eliminating the need for front end
2-IN-1 S-CAM BRAKE TOOL
Comprised of a steel shaft with a U-shaped fork on one end to stretch the retaining spring so that both halves of the brake shoe are held together, which enables the user to hook up the pin. An S-shaped device on the opposite end enables the user to position the brake shoes in a way that allows leverage for installation of the rollers.
• (5) adapters for 2- and 4-wheel disc brake assemblies of most cars
• May be used on or off the car
• Helps prevent damage to the piston and boot
2-PC. TRUCK ANCHOR PIN BUSHING DRIVER
Includes an 11-1/2” long driver that allows bushings to be driven straight without removing the hub assembly. Double-sided cone snaps onto driver to drive out and install bushings. Also removes truck leaf spring bushings.
BRAKE PISTON WIND BACK TOOL, 2 & 3 PIN
• Adapter will work on right or left hand rewind calipers
• 2 Pin range is from 1/2” to 1-1/2”
• 3 Pin range is from 1” to 1-11/16. Use with a 3/8” square drive
11-PT. TRUCK BRAKE CALIPER SOCKET
• 11 Point Socket for Air Disc Brake Caliper Adjustment
Works on Bendix
BRAKE SPRING BAR
• Slip the hook into retaining spring loop and press down against the axle to remove spring. Lever action against the axle eliminates need for wrenches, pry bars and screwdrivers. Tool is 18” long with a molded handle for comfort. The tool has a black oxide finish.
• The tip design cradles the return spring to keep it from sliding off. Heat treated material and extra-long shaft provides strength and stability. Ergonomic handle for comfort.
SMALL BRAKE CALIPER PRESS
• Works on small and medium single piston brake calipers found in subcompact to midsize cars with single piston calipers • ACME screw for durability
• Size Range: .95” to 2.25” (compared to 1.5” to 3” on the Lang 279)
BRAKE CALIPER PRESS
• Works on twin & quad piston fixed calipers,and single & twin piston floating calipers
• Size Range: 1.5” to 3” • Made in USA
BRAKE SPRING FORK BENDIX/KNORR-BREMSE AIR DISC BRAKE PAD RETAINER TOOL
• The only tool for servicing Bendix/Knorr-Bremse air disc brakes
• A safer and easier way to remove pad retainer
2-PC. AUTOMATIC SLACK ADJUSTER TOOL SET
• Specifically designed for installation and servicing of Meritor air brake systems
• 5/16” double-square head reversible wrench with built-in ratcheting mechanism is offset to provide increased clearance
HEAVY-DUTY TORQUE MULTIPLIER
• Gear Ratio: 58:1
• Max Torque: 2950 ft.-lbs. (4000nm)
• 1” Square Drive
• (2) Sockets: 33mm (1-5/16”)
•
4-PC. FLIP SOCKET SET
• Constructed with high grade steel and feature a heavy-duty welded drive bar for added strength
• Black E-coating for long lasting corrosion protection
• Manufactured to strict quality standards for an exact fit and precise operation
• Lifetime warranty
4-PC. 1/2” DR. SAE/MM THIN WALL DEEP PROTECTIVE IMPACT WHEEL NUT FLIP SOCKET SET
• Outer protective sleeves and inner plastic inserts to prevent damage to custom wheels and decorative lug nuts
• Color coded for easier identification and packed in
7-PC. 1/2” DR. SAE/METRIC
BRAKE & WHEEL
MASTER MACPHERSON STRUT TOOL (ATD-7585)
• Built-in detent pins lock coil in place and quickly compress springs
• Repair bent struts, strut tubes and damaged pieces
COIL SPRING COMPRESSOR (ATD-7549)
• Compresses coil springs for installation and removal of springs and spacers
• Fits most American and some imported cars and trucks
COIL SPRING COMPRESSOR
• Compresses coil springs for installation and removal of springs and spacers
• Can be used with an impact wrench or hand tool
MASTER MACPHERSON STRUT TOOL MASTER SPRING
• Utilizes compressed “shop-air” for dispensing and extracting
• Isolated flow control and pressure/vacuum switch valves provide simple functionality control
• 2-quart capacity reservoir
• Includes flex hose w/control valve and wand and Master Cylinder adapter kit
For use with Mityvac hand vacuum pumps to remove trapped air from power steering systems. Each adapter is designed to fit snugly in the neck of the power steering reservoir to form an air-tight seal when vacuum is applied. Includes rubber cone shape 5/8”-15/18”, GM two-tab cap, and Ford 1-1/4” or 2”.
MACPHERSON STRUT SPRING COMPRESSOR
• Repair bent struts, strut tubes and damaged pieces
• Built-in detent pins lock coil in place and quickly compress springs
This compressed-air-operated compact unit offers professional-grade brake and clutch bleeding performance at up to 2 qt. per minute. Kit includes an advanced selection of accessories that helps to ensure maximum convenience and performance for greater productivity.
This innovative cap is a game-changer for hybrid and electric vehicle brake pressure bleeding, making your maintenance tasks smoother and more efficient.
Features
• 2 Honda specific caps
• Tesla specific cap
• Nissan / Infinity Hybrid specific cap
• 2 Ford caps
• 1 Ford / Tesla specific cap
STRUT SPRING COMPRESSOR
Known as the standard in the industry, the 7600 handles the heaviest coil-over-shocks on light trucks and SUVs, without needing additional adapters. It also has longer handles for extra torque. Made in USA
Specifications:
• Max Spring Compression Capacity: 3,000 lbs.
• Min/Max Spring Diameters: 3.5”/11.5”
11-PC. PRO SERIES BRAKE BLEEDER ADAPTER SET
• Services most makes and models on the road today, including new EV applications
• Most adapters feature a 90° swivel connection fitting for when space is limited
• Designed to work with 7015 Pressure Bleeder Tank
• Adapets have standard European (Nitto) fittings, but kit includes : 9 Master Cylinder Adapters, 1 Quick Coupler & 1 Milton adapter
Professional hydraulic brake and clutch bleeding system that includes a 1.2 gal. fluid dispenser with manual pump and a kit containing seven master cylinder adapters. A pressure gauge on the dispenser allows control of the system pressure, and the pressurized reservoir allows the operator hands-free movement to the bleed screws.
ELITE AUTOMOTIVE TEST KIT
Diaphragm-type bleeder that keeps fluid and air separated with large 4-gallon reservoir that
Compact design features a 1.3 qt. reservoir and powerful compressed-air-operated venturi that quickly draws out fluid and air from hydraulic brake and clutch systems. One person can perform quick, clean vacuum brake and clutch bleeding. Automatic shutoff pervents overfill. 4 ft. long bleed hose.
The original Mityvac hand vacuum pump kit used by service professionals worldwide for performing hundreds of automotive diagnostic and mechanical tests and for one-person brake bleeding. Contains Mityvac’s most popular Selectline hand vacuum pump with vacuum gauge and accessories.
Includes the original Selectline hand vacuum pump and all accessories necessary to perform one-person brake bleeding on automobiles, motorcycles, ATVs, snowmobiles, etc. Also works great for siphoning or transferring fluids from tanks amd reservoirs. Includes (4) adapters & (2) connection tubes & 4.5 oz. fluid reservoir bottle.
BRAKE BLEEDING KIT
Uses compressed air to generate deep vacuum. Float valve shuts vacuum down when container is full. Universal rubber fitting holds securely on brake screw. Clear drain hose for visual inspection of old fluid.
• Graduated in .001”/.01mm increments
• Range: 4”-20.65” (150mm-515mm) with selectable depth stops
• Easy to read digital display with SAE/Metric conversion
• Pointed anvils and 4.25” long arms to inspect drums
• Works on Mercedes, Audi, BMW, Mini-Cooper, SAAB and Volvo
• Guides support wheel/tire so technician can easily thread lug nut bolts into brake rotor
• Each kit includes one 12mm and one 14mm stud
WHEEL WEIGHT TOOL
• Includes lever and offset flat tip for removing wheel covers
• Removes, trims and installs clip-on wheel weights
ADJUSTABLE LUG NUT COVER REMOVER
Used When Removing Chrome Lug Nut Caps Found On Heavy-Duty Trucks, Trailers And Motor Homes. Plastic coated jaws prevent tool from slipping off the cap and scratching the chrome finish. Two-position, slip joint handle, allows the tool to work on small and large caps. Double-dipped handles for comfort.
INCLUDES: free mini tubing cutter!
VALVE CORE TORQUE TOOL
• Properly installs and removes valve cores, including late model vehicles with the tire pressure monitoring system
ATD-5463 Double Flaring Tool Kit
(PRT5464-01), 6mm adapter (PRT5464-02), 8mm adapter (PRT5464-03), 10mm adapter (PRT546404). Adapters are also available individually.
Works on copper, aluminum, soft steel, brake line and brass tubing to 45˚. Includes: 3/16” adapter (PRT5463-01), 1/4” adapter (PRT5463-02), 5/16” adapter (PRT5463-03), 3/8” adapter (PRT5463-04), 1/2” adapter (PRT5463-05) and storage case. Adapters are also available individually.
Kit Fabricates: Push Connect Flares: 1/4, 5/16 and 3/8”; GM Fuel Line Flares: 5/16 and 3/8”;
TREAD
• Helps prevent valve core leaks causing low tire pressure and possible TPMS alerts • Wide base for big treads
Fractional scale (32nds only) • 1”+ range
DELUXE STEERING WHEEL REMOVER AND COLUMN SERVICE TOOL
Includes: Steering wheel puller, special puller legs for steering wheels without threads, lock plate compressor tool to remove snap rings, pivot pin remover for GM, Chrysler and Ford tilt columns
2-PC. SEAL PULLER SET
• Pin location affects the positioning of the tool
• Greater surface area on hook prevents seal puller from ripping through the seal
Set Includes: Small and large sized pullers for use with 3/8” breaker bar or ratchet; 2” and 4” pins for various diameter seals
TRUCK WHEEL PAN
Prevents oil mess during wheel repair. The pan fits rims with 13-3/4” ID and larger. Handle compartments hold hub nuts out of the oil. Made of polypropylene for durability. Will not warp if oil is warm.
$44.95
BRAKE & WHEEL
45-PC. TIRE REPAIR TOOL KIT
• (1) T-Handle
Collet sets expand pipes from 1-5/8” to 4-1/4”. Comes in a molded storage case. Expands all types of exhaust pipe, including stainless steel, from 1-5/8” to 4-1/4” in size.
3 PC. TAILPIPE EXPANDER SET
• Small Expander: 1-1/8” to 1-3/4” • Medium Expander: 1-1/2” to 2-1/2”
• Large Expander: 2-1/8” to 3-1/2” • (3) Spare sets of rubber O-rings
EXHAUST PIPE CUTTER PLIERS
HARMONIC BALANCER INSTALLER KIT
Set includes driving screw, thrust bearing and 13 threaded adapters necessary to work on a wide range of domestic and some import harmonic balancers. Five long adapters for use on Dodge Hemi, generation III and IV GM motors, some Chrysler and some Ford including 3.5L and 4.0L.
LATE MODEL HARMONIC DAMPENER PULLER & HOLDING TOOL SET
• 3-jaw
• Heavy-duty, flange-type puller easily pulls harmonic balancers, timing gears and other parts with bolt circle diameters from 1-1/2” to 4-5/8”
• Works on most cars - large and small, foreign and domestic
• Will pull parts with tapped holes like flywheels, gears and pulleys
HARMONIC BALANCER PULLER SET
This kit includes a standard harmonic balancer puller, pulling screws, adapters for 3300 and 3800 GM V6 engines, and a harmonic damper pulley puller for Chrysler, GM, Mitsubishi and Dodge. Includes new interchangeable puller jaws for 3.6L V6 Chevy Camaro and Dodge 5.7L Hemi.
the jaws happen simultaneously when you turn the T-handle.
HARMONIC BALANCER PULLER SET RATCHETING HARMONIC BALANCER PULLER
bearing removal takes minutes, not hours when using PTTJ-1 or PTTJ-2
SPARK PLUG TESTER
•
•
•
COIL-ON-PLUG WIRE
• Gives a visual check of spark energy for coil on plug or standard ignition systems
• With engine running, the tool flashes a mirror image of the ignition spark • Additional 7” extension plug wire for recessed, hard-to-reach coil on plugs
14MM, 12-PT. SPARK PLUG SOCKET
UNDER HOOD
6-PC. SPARK PLUG & GLOW PLUG SOCKET SET
• For removal and installation of Spark Plugs, Glow Plugs and Pressure Sensor Glow (PSG) Plugs
• Includes 5 plug protectors for sensitive PSG plugs
• Includes: 8mm x 6-point; 9mm x 6-point; 10mm x 6-point; 12mm x 6-point; 14mm x 12-point; 16mm x 6-point
3/8” DRIVE 10-PC. MASTER SPARK PLUG SOCKET SET
• Seven of the most popular spark plug socket sizes for use on a majority of foreign and domestic vehicles
• Sockets are equipped with internal magnets to securely hold spark plugs in place during both removal and installation processes
5-PC. SPARK PLUG THREAD CHASER TAP SET
• Restore and clean threads in spark plugs, Nox & O2 sensors and many other applications
• Includes M10x1.0, M12x1.25, M14x1.25, M18x1.5 & M20x1.5
• Works with hex deep well socket or 3/8” square drive
3-PC. 3/8” DR. 5/8” SPARK PLUG SOCKET SERVICE KIT
• Long reach magnetic swivel spark plug set in 4”, 6” and 11”
• Features magnetic core on each size • Packed in a blow molded case • Porcelain pusher
square drive with chrome finish. Set includes: 10mm, 11mm, 12mm, 13mm, 14mm, 15mm, 16mm, 17mm, 18mm and 19mm
FORD DIESEL FUEL FILTER WRENCH VARIABLE PIN SPANNER WRENCH
• For Ford power stroke and International/ Navistar
• Low-profile design for easy access in tight quarters
Accommodates the most common metric size pin configurations including: 3.5mm, 4mm, 4.5mm, 5mm, 6mm, 7mm and 10mm
Holds the timing chain and gear in place while removing or installing water pump on Ecotec engines.
Slot in tool has been modified to fit larger connectors on injector pressure regulators found on International diesels. Use with 3/8” square drive
FUEL TANK LOCK RING KIT Channel design on body allows 2 inter changeable sets of legs to adjust to fit rings from 4” to 7-1/4” and keeps the drive centered
• 8 position ratchet locks reel at desired hose length
• Power spring with substantial output torque and long service life
• Base slots to facilitate mounting and adjustment
• Base and guide arm made of heavy-gauge steel stampings with reinforcing ribs
AIR HOSE
POLYURETHANE RECOIL HOSE
Assembled in USA • Warranty: 1 year
• Ideal for spray guns (point of use)
• 40 micron porous bronze element removes fine dirt particles, as oil removing media removes oil vapor and desiccant beads absorb water vapor
• Attached directly to spray gun or mini regulator located on spray gun
• Operating Temperature Range: 35˚-130˚ F
• Unit is bi-directional with 1/4” NPT
• Max. Operating Pressure: 125 psi
• Max. Flow Capacity: 15 SCFM
PURPOSE FILTERS
ELECTRIC TANK DRAINS FOR AIR COMPRESSOR TANKS
• Automatically drain water & contamination at set times
• Increase
• Available in 1/4”, 3/8” and 1/2” NPT
• Available in 115V and 230V
StageAir DESICCANT DRYING SYSTEMS
FIRST STAGE:
• First filter - 5 micron water removing filter with 9 oz. bowl, sight glass and overnight drain
SECOND STAGE:
• Second filter - .01 micron oil removing filter with 9 oz. bowl, sight glass and overnight drain.
THIRD STAGE:
• Third filter - 2 quart desiccant
FOURTH AND FIFTH STAGES:
REGULATORS
AIR CONTROL GAUGE
PRESSURE GAUGE
and
• Filtering - 3 micron filter with 9 oz. bowl and sight glass - final filter protects paint job from any possible dirt or desiccant dust or debris. Gauge included with regulator.
