AZ Press Parts Catalog by Pam Crespo

2007 - 2008 EDITION YO

00 ,0 AX AS R 00 H OU 1 K. R F R C ET OF VE TO L O L KL E O PL F O IN S CA BO AM Y O S T IS S R EM JUS TH Y A TO IT IT L N T N E N E O INV RE SE L FE ’T TA IF ON TO D U D

PRINTER’S PARTS STORE

SAME DAY SERVICE 97% OF ALL REPLACEMENT PARTS I N S TOCK QUICK SERVICE, LOWEST PRICES, AND IMMEDIATE SHIPMENT. CALL US AT 1-800-922-2425 OR FAX US AT 1-480-922-8550 R e p l a c e m e nt parts available for

A . B . D I C K • C H I E F • D AV I D SON • GESTETNER • HAMADA Pages 1-6

Pages 32-35

Pages 36-39

Pages 31-34

Pages 18-20

HEIDELBERG • ITEK • MULT ILITH • RY OBI • TO WNSEND-51 Pages 21-31

Pages 13-16

Pages 7-12

Pages 13-16

Page 17

SAVE ON SHIPPING BY USING YOUR VISA, MASTERCARD, AMERICAN EXPRESS, PAYPAL, OR CHECKS-BY-FAX

PRICES ARE SUBJECT TO CHANGE

Replacement parts for: A.B. DICK 350, 360, 360PRO, 369, 8805, 8810, 8815, 8820, PART # A

B B

FILTER ASSEMBLY (A) Tube (B) Filter (need 2) Plug (not shown)

A C

G D

E F

PART #

P-1147 P-1146 P-1148 P-1150

TABLE RAISE HANDLE ASSEMBLY 350, 360, 375 For feeder 9805 - 9850 For feeder 380, 385 For feeder Chain del. 350,360,375,385 Chain del. 9800

••• Rather than buy a new cradle, replace only the parts that wear. CRADLE REPAIR KIT - For 8800 & 9800 series. Complete Kit P-98037 (A) Washer P-613 (B) Hex nut - 2 ea. P-514 (C) Retaining ring P-707 (D) Shaft P-98038 (E) Key P-1745 (F) Ball bearing - 2 ea. P-11149 (G) Steel bushing P-98058 (H) Cradle (w/ shaft and bearing) P-98041

P-36955 P-98955 P-38955 P-362630 P-982630

TABLE RAISE GEAR & RATCHET ASS’Y. For feeder hand crank on 350, 360, 375, 9800 350, 360, 375 (complete) P-36975 9800 P-98975 Gear P-36974 Ratchet 350, 360, 375 P-36973 Ratchet 9800 P-98973 Screw (3 needed) P-44

PUMP VANE (need 4 per pump) 350, 360, 375, 8800, 9800 P-1159 380, 382, 385 P-1931 FLEXIBLE SPEED CONTROL SHAFT For the 8800 & 9800 series Shaft P-98053 Set screw P-7

TABLE RAISE SHAFT ASSEMBLY - 9800 Complete Shaft Gear Sprocket

CRANK ASSEMBLY Speed control

Complete - 350, 360, 375, 385 Complete - 9800 (A)Handle (B)Spring for handle Mounting screw SPEED PULLEY Variable Heavy duty (all steel)

COUNTER ASSEMBLY Complete Counter Mounting screw Arm Screw for arm Wheel (screw on type) Screw for wheel

P-36060 P-98060 P-36062 P-36410 P-299

P-1630 P-1631

P-1539 P-36087

••• MADE OF DURABLE ZINC DIE CAST!

A C

F E D

STOCK RETAINER PLATE GUIDE 350, 360 Center P-36712 350, 360 Right hand P-36092 350, 360, 375, 9800 Left hand P-36089 385 Back guide plate P-38089 MICRO GUIDE ADJUSTING KIT FOR ACCURATE FEED & REGISTRATION 350, 360 P-36113 375, 9800 P-37113

BACK PAPER GUIDE

P-36090

THUMB NUT

P-1058

SPRING GUIDE 350, 360, 375 385 Side 385 Back Screw

P-36088 P-38088 P-38090 P-984

TABLE RELEASE LEVER ASSEMBLY 350, 360, 375, 385 P-36969 9800 P-37969

P-36952 P-36954 P-229 P-36956 P-151 P-36958 P-1056

COUNTER SENSOR SWITCH 9900 Series

FEEDER CLAMP Thumb screw Adjusting clamp

P-98070 P-98102 P-38103 P-36101

P-9814

BLEEDER VALVE ASSEMBLY Complete P-36847 (A) Valve body P-36844 (B) Shaft P-36841 (C) Plug P-36951 (D) Spring (inside) P-36859 (E) Valve (inside) P-36845 (F) Roll pin P-379

SUCKER TUBES WITH SHUT OFF VALVE ON BOTTOM ••• Ideal for envelope runs and T-Heads. Shut off tube P-36990 Sucker tube (standard) P-36174 Paper leveler assy. P-36164 Paper leveler tube P-36166 Plug P-36172 Compensating sucker tube w/shut off valve P-36966 SUCKER FOOT •••P-1555 MATERIAL IS NEW TACKY GUM RUBBER TO ENSURE BETTER SHEET PICK UP. All presses (cup) each P-1555* Extra heavy (cup) each P-5219 Flat disc (3/4” dia.) each P-1552 Flat disc (1/2” dia.) each P-1554 *Note: P-1555 Sold individually or in bags of 50 or 100. BLOWER TUBE SHUT OFF VALVE - All models P-36760

SPRING For feed roller support arms P-36177

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

375, 9805, 9810, 9815, 9820, 9835, 9840, 9850, 9865, 9870, 9880, 380, 382, 385 PART #

PART # PAPER STOP Impression cylinder 350 P-35241 360 P-36241 375, 9800 P-37241

UPPER FEED ROLLER 350, 360 375, 9800 9870, 9910XCS, 9910 XCS 385 Arm 350, 360, 375, 9800 Bearing (plastic)

P-36157 P-37157 P-98157 P-38157 P-36175 P-1566

LEVER ASSEMBLY For impression cylinder P-36207 SEGMENT Imp. cylinder

P-36203

SHAFT & LEVER ASSEMBLY For upper feed roller Complete 350, 360 Complete 375, 9805 - 9850 Shaft only 350, 360 Shaft only 375, 9805 - 9850 Lever (operators side) Lever & cam assy. (n.o.s.) Pin

P-36147 P-37147 P-36149 P-37149 P-36171 P-36151 P-349

GRIPPER SHAFT ASSEMBLY For impression cylinder Complete 350, 360 P-36229 Shaft only P-36231 Gear P-36235 Taper pin P-421 BLANKET CYLINDER SHAFT 350, 360 P-36290 375, 9800 P-37290 380, 382, 385 P-38290

STUD - For feed roll shaft assembly 350, 360, 375, 385, 9800

P-1561

STUD - For upper forwarding feed roll shaft assembly. 9870, 9890 P-8270 SCREW - For P-8270

P-6512 PRINT ADJUSTING DRAW ROD 350, 360 (30° pressure (20° pressure 375, 9800 (30° pressure (20° pressure 385 (30° pressure (20° pressure RETAINER NUT

SUPPORT ARMS - For upper feed roller Operators side Non-operators side

P-36153 P-36155

FINGER ASSEMBLY & BLOWER TUBE 350, 360, 375, 9800 P-36158 385 P-38158 HOSE For blower tube 350, 360, 375, 9800 380, 385

P-1189 P-1677

PAPER SENSOR For AB Dick 9800 Complete P-98269 Sensor arm P-98974 Spring P-98581

P-36180 P-36308 P-37180 P-37308 P-38180 P-38308 P-36182 P-36186

77.90 54.90 77.90 39.90 104.90 66.00 6.00 10.50

69.80 164.50

1.80 4.80

SOLENOID 9800 impression cylinder power lever P-4029

angle) angle) angle) angle) angle) angle)

BLANKET CYLINDER RING SEGMENTS ••• New style - Case hardened for longer wear. Left hand P-36194 Right hand P-36195

62.00 62.00

57.30

57.90 2.40 4.90

(A) SCALE Blanket cylinder raise & lower 2 screws needed

P-36208

2.90

(B) SCALE Blanket cylinder adjustment 5 screws needed

P-36202

6.90

DRIVE SCREW For both scales (not shown)

P-1040

.60

BLANKET BARS Standard 360 375, 9800 380, 382, 385 Serial #1305 & below 9880 Mounting screw Blanket screw

P-36252 P-37252 P-38252 P-988252 P-36204 P-124

FEELER CONTROL LEVER ASSEMBLY 350, 360, 375, 9805, 9810, 385 P-36839 IMPRESSION CYLINDER GRIPPER FINGERS ••• Sand blasted tips for better grip. 350 (1/2”) P-35225 360, 385 (1/4”) P-36225 375, 9800 (small) P-37224 375, 9800 (large) P-37225 Mounting screw P-268

145.80

39.90 25.90 22.00 25.90 .60

PAPER WEIGHT BAR Light weight 350, 360 Heavy weight 350, 360 Light weight 375, 9800 Heavy weight 375, 9800

P-36094 P-36093 P-37094 P-37093

18.90 15.00 12.00 12.60

125.90 136.00 300.00 319.90 2.00 .60

QUICK CHANGE BLANKET BARS ••• Save time & money by changing only 4 screws to mount your blanket. 360 P-36777 129.90 375, 9800 P-37777 139.90 380, 382, 385 P-38777 340.00 9880 P-988777 380.00 Mounting screws P-36204 2.00 Blanket screws P-124 .60

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

Replacement parts for: A.B. DICK 350, 360, 360PRO, 369, 8805, 8810, 8815, 8820, PART #

PART #

BEARING HOUSING COMPLETE For blanket cylinder • Made of “REINFORCED STEEL” for longer life. • Completely enclosed for added strength. (A) Operators side (B) Non-Operators side

P-36295 P-36283

109.80 109.80

BLANKET CYLINDER ADJUSTING SHAFT 350, 360, 375 9800

P-36236 P-98236

42.00 95.10

CHROME WATER DUCTOR ROLLER (SMOOTH) 350, 360 P-36342-S 375, 9800 P-37342-S

339.90 380.00

CHROME WATER DUCTOR ROLLER (ROUGH) 350, 360 P-36342-R 375, 9800 P-37342-R

369.90 389.90

WATER FOUNTAIN ROLLER 350, 350T, 357, 357A, 367, 367A (Smooth Aluminum) 360, 360CD, 360T (Rough Aluminum) 375, 9800 (Rough Aluminum)

179.90 179.90 189.90

OVED IMPR IMPRESSION

INNER BLANKET

MASTER

CYLINDER GEARS ••• All cylinder gears are made with “SOLID STEEL” for longer life.

Master cylinder gear 350, 360, 375 Master cylinder gear 9800

P-36313 P-98313

246.90 294.90

Inner blanket cylinder gear 350, 360, 375 5/16” wider than standard for longer life. Inner blanket cylinder gear 9800 “Wide” inner blanket cylinder gear Outer blanket cylinder gear 350, 360 Outer blanket cylinder gear 369 Outer blanket cylinder gear 375, 9800 Outer blanket cylinder gear 385

P-36214

302.00

P-98214 P-36211 P-36196 P-36198 P-37196 P-38196

249.90 308.50 320.00 261.00 259.90 246.00

Impression cylinder gear

P-36191

123.90

PLATE CYLINDER UPPER SUPPORT ARMS 350, 360 P-36801 375, 9800 P-37801

69.90 60.00

PLATE CYLINDER LOWER SUPPORT ARMS 350, 360, 375, 9800(9/16” hole) P-36833

72.50

STUD - For master cylinder support arm. 9890, 9900 P-4577

P-36399 P-36244

3.50 4.50

8.40

NIGHT LATCH IDLER GEAR Brass P-36446 Steel P-36457 Nylon P-36455

29.90 78.00 22.90

1.40 .80 .60 1.00

SINGLE LEVER CONTROL ARM

9.00

19.90

*ALL PARTS SOLD SEPARATELY.

••• The valve assembly is made of hardened plastic which helps eliminate build up and rust. P-1915 P-1919

21.90 59.80

COUPLING ASSEMBLY For water waver roller ass’y. P-36426

•••Shaft is universal, fits old & new style.

TIRE Form roll knobs TIRE Ink fountain knob

P-36856 P-98856 P-36860 P-36858

89.90 104.00 85.90 18.70

INK OPERATING PAWL For ink metering fountain 360 Pro P-36251 42.90 9800 P-98251 39.00 SPRING For lower ink oscillator P-36459

4.60

74.90

COUPLING HOUSING For water waver roller ass’y. P-36432 37.50

350, 360 375, 9800* 9800 PRO

360 Complete 9800 Complete (without knob) Knob

WATER FOUNTAIN BOTTLE ASSEMBLY.

(1 quart) 350, 360 only (2 quart)

2.20

35.90 49.00

IDLER GEAR Water section Plastic P-36368

P-36376 Shield P-658 Spring washer P-617 Flat washer P-706 Retaining ring

COMPRESSION SPRING (Painted Red) For water waver roller P-36413

22.90 16.00 9.80

P-36378 P-37378

2.90

Consists of 2 ea.

HOUSING P-36322 P-36366 P-746

SHAFT For water repellant waver roller

WATER FOUNTAIN HOSE P-1549

HARDWARE REPAIR KIT For Super Aquamatic. Complete P-36376-K

WATER DUCTOR ROLLER Housing (cone hub) Housing (flat hub) Bearing

P-35364 P-36364 P-37364

FORM ROLL SHAFT 350, 360 375, 9805 - 9850, 9865, 9870

P-36401 P-37401

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

85.80 125.90

375, 9805, 9810, 9815, 9820, 9835, 9840, 9850, 9865, 9870, 9880, 380, 382, 385 PART #

PART #

F&G I

A&B

MASTER CYLINDER HEAD CLAMP ASSEMBLY For 9800 - consists of all items shown COMPLETE P-98352 (A) Screw P-253 (B) Head clamp P-98353 (C) Screw P-43 (D) Hinge P-98299 (E) Plate clamp P-98359 (F) Knob P-98175 (G) Spring P-36707 (H) Washer P-592 (I) Eccentric pin P-98351 (J) Retaining ring P-668 (K) Bracket P-98171 (L) Bar P-98387 (M) Screw P-257 (N) Shoulder screw P-8042 (O) Retaining ring P-666 (P) Bracket P-98181 (Q) Spring P-36349 (R) Thumb screw P-98347 (S) Bracket P-98153 (T) Screw P-37 (U) Radial bar P-98393

579.90 .60 280.00 .60 25.00 53.00 23.90 1.30 .60 59.90 .60 5.00 111.90 .60 7.50 .60 5.00 .90 29.90 28.50 .60 82.90

FORM ROLL SEPARATING SHAFT 9800/9900 Complete (A) Roll pin (B) Collar (C) Cam - non-operators side (D) Shaft only (E) Cam - operators side (F) Eccentric collar (G) Set screw (H) Taper pin ( I ) Separating lever

P-98497 P-382 P-739 P-36623 P-37499 P-36503 P-747 P-8 P-424 P-98505

180.00 .60 3.90 49.90 73.90 49.90 12.90 .60 .60 44.90

INK DUCTOR LEVER ASSEMBLY Complete P-36572 Lever only P-36569 Bushing 360, 375, 9800 P-1569 Bushing 380, 382, 385 P-1568 Retaining ring P-703

19.90 12.50 4.30 32.90 .60

SEAL For ink fountain roller - 360Pro & 9800 (need 2) P-36262 4.60 INK DUCTOR OPERATING CAM P-36542

46.90

INK ROLLER RATCHET ASSEMBLY 360 PRO 9800 PRO, 9900

P-36263 P-98263

74.90 128.00

Ratchet only

P-36239

45.90

IMPROVED ••• DESIGNED WITH REPLACEABLE “STEEL” END CAPS AND A DEEPER INK WELL FOR 50% MORE INK CAPACITY.

HEAD & TAIL CLAMP ASSEMBLYFor 350, 360 COMPLETE - 360 consists of all items shown COMPLETE - 375 consists of all items shown TAIL CLAMP ASSY. (A - F) TAIL CLAMP ASSY. (A - F) (A) C-Ring (B) Tail clamp (360) (B) Tail clamp (375) (B) Tail clamp (9800 not part of kit) (C) Pivot screw (D) Spring (E) Thumb screw (F) Spring HEAD CLAMP ASSEMBLY (G - S) HEAD CLAMP ASSEMBLY (G - S) (G) Lateral adj. knob (H) Washer ( I ) Spring (J) Pin bar (360) (J) Pin bar (375) (K) Bracket (360) (K) Bracket (375) (L) Spring (M) Washer (N) Spring washer (O) C-Ring (P) Screw (Q) Hinge (360 & 375) (Q) Hinge (9800) (R) Stop plate (360) (S) Vertical adj. knob

P-36354 P-37354 P-36606 P-37606 P-666 P-36323 P-37323 P-98323 P-36331 P-36325 P-1027 P-36327 P-36352 P-37352 P-36347 P-569 P-36349 P-36345 P-37345 P-36353 P-37353 P-36032 P-586 P-1049 P-668 P-892 P-36299 P-98299 P-36359 P-36351

406.00 599.90 129.90 214.90 .60 99.90 137.80 129.90 9.90 1.90 4.50 3.30 270.00 399.90 22.00 .60 .90 219.90 204.90 200.00 209.80 3.80 .60 .90 .60 .60 8.00 25.00 139.80 19.90

INK FOUNTAIN ASSEMBLY 350 Complete Fountain only Wire 360 Complete Fountain only Wire 360 PRO Complete Fountain only 375, 9800 Complete Fountain only Wire 9800PRO Complete Fountain only All models Adjusting screw 350, 360, 375, 9800 End caps 360PRO, 9800PRO End caps 350 360, 360PRO 375, 9800 385

360 9800

P-35071 P-35072 P-35084 P-36778 P-36789 P-36084 P-36805 P-36807 P-37778 P-37789 P-37084 P-98805 P-98807 P-1570 P-36792 P-98792

624.00 440.00 2.50 348.50 199.80 2.90 405.20 199.80 348.50 209.90 2.90 400.00 204.90 6.00 52.90 52.90

P-35079 P-35233 P-36079 P-36233 P-37079 P-37233 P-38079 P-118

49.50 99.90 42.90 84.90 72.90 89.90 149.90 .60

METERING BLADE With studs 3-5/8” wide P-36095 3-5/8” wide P-98095

104.90 132.00

INK FOUNTAIN BLADE 1-3/4” wide 2-7/8” wide 1-3/4” wide 2-7/8” wide 1-3/4” wide 2-7/8” wide Standard width Screw

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

Replacement parts for: A.B. DICK 350, 360, 360PRO, 369, 8805, 8810, 8815, 8820, PART #

PART #

HEAVY DUTY CAM KIT For ink ductor P-36500 9.90 ••• Uses a bearing in place of the Cam to prevent premature wear.

INK FOUNTAIN HAND CRANK 9800 P-98402

90.00

DRIVE SHAFT AND GEAR ASSEMBLY COMPLETE 350, 360 P-36577 375 P-37577 9865 P-98577-65 9870 P-98577-70 DRIVE SHAFT

IMPROVED

C E

360, 375, 9800 9800 QPC, PRO

360

BLOCK IS COLD WELDED WHICH MAKES IT LESS BRITTLE. CLUTCH PULLEY ASSEMBLY Complete hub I.D. 1/2” P-36597 Complete hub I.D. 7/8” P-98597 (A) Spring P-36591 (B) Pinion P-36595 (C) Link P-36593 (D) Lever P-36605 (E) Pulley only 360 P-36587 (E) Pulley only 9800 P-98587

324.90 324.90 12.90 39.90 8.00 59.90 132.90 97.00

350, 360 375 9800 - 1/2” O.D. 9800 - 5/8” O.D. 9865 9870 380, 385

P-36583 P-37583 P-98583 P-98388 P-98583-65 P-98583-70 P-38583

74.90 124.90 245.80 150.00 42.90 97.90 92.90 89.90 218.90 121.90 190.00

HOUSING Non-operators side 350, 360 P-36487 375 P-37487 9800 TD/CD/QP/QPC/PRO P-98487

44.90 119.90 56.40

HOUSING ASSY.

143.90

9800 TD/CD/QP/QPC/PRO P-98385

HOUSING Operators side 350, 360 375, 9800 9800 QPC, PRO

P-36585 P-37585 P-98585

49.90 107.80 92.90

DRIVE GEAR

P-36581 P-38581

34.90 36.90

P-98540 P-98562

214.90 529.90

350, 360, 375 9800, 380, 385

OVERSIZED CLUTCH PULLEY For thermographers Complete P-36589 362.90 Pulley only P-36599 167.90 SPRING HOLDER & SLEEVE KIT Used in place of old design single piece. 9800 Series P-98595-K

52.90

SENSOR For 9800 clock sync. mechanism Male connector P-4047

26.00

SENSOR For 9800 clock sync. mechanism Female connector P-4032

34.90

CONTROL PANEL OVERLAY & MEMBRANE (A) 9815, 9850 (B) 9870 POWER SUPPLY

9800 Control box (5V. 115V.) P-4401

329.90

FEELER LINK OPERATING LINK ASSEMBLY 350, 360, 375, 9800 380, 382, 385

P-36885 P-38885

66.80 133.50

DRIVE & PUMP SWITCH Old style (drive & pump) - 2 position with screw connectors P-36977 22.00 (385) Momentary - 3 position with tab connectors P-38977 31.00 New style (motor) momentary- 3 position with tab connectors P-36303 19.90

GAP CONTROL SHAFT ASSEMBLY 350, 360 Complete 375 Complete 9800 Imp. Cyl. Complete 9800 Master Cyl. Complete 350, 360 Shaft only 375 Shaft only 9800 Imp. Cyl. Shaft only 9800 Master Cyl. Shaft only 350, 360, 375, 385 Dial assy. 8800, 9800 Dial assy.

P-36689 P-37689 P-98689 P-98693 P-36695 P-37695 P-98695 P-98697 P-36688 P-98688

169.90 194.90 139.50 140.00 55.00 62.90 84.00 84.00 84.50 80.00

New style (pump) - 3 position with tab connectors P-36307 16.00 New style (pump) - 2 position with tab connectors P-36305 12.50

RELAY - 9800 Control box

P-4037

36.00

MICRO SWITCH Chain delivery safety guards HANDWHEEL 350, 360, 375, 8805/10

P-36615

SPLINE DISC Safety handwheel P-99665

P-362940

38.80

TIMING PULLEY ASSEMBLY 350, 360, 385 P-362080 375, 9800 P-372080 Shaft only 350, 360, 385 P-362040 Shaft only 375, 9800 P-372040 Pulley only all models P-362120

40.90 89.90 5.10 49.90 35.90

112.90

32.90

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

375, 9805, 9810, 9815, 9820, 9835, 9840, 9850, 9865, 9870, 9880, 380, 382, 385 PART #

PART #

JOGGER OPERATING LEVER - New style 350, 360, 375 P-361610

72.90

SIDE JOGGER LEVER 9800

P-984130

24.00

LEVER SUPPORT

P-984140

27.80

GEAR & SHAFT ASSEMBLY Chain delivery P-36754 Chute delivery P-36752 385 P-38754 9800 P-98754

SHAFT & SPROCKET ASSEMBLY 350, 360 (12-1/4” Inside sprocket to sprocket) 350, 360 (12-1/16” Inside sprocket to sprocket) 8810 375, 9800 Standard 9800, 1-1

122.90 135.80 329.80 122.90

P-361160 P-361165 P-881160 P-371160 P-981160

559.90 559.90 499.90 559.90 559.90

BACK STOP 350, 360, 375 9800 9800, 1-1

P-362420 P-984320 P-982420

129.90 140.00 69.90

IMPROVED ••• Made with spring steel & nickel plating which prevents cracking and adds better spring action & durability.

BACK STOP SPRING Complete with cam 350, 360, 375, 385 Complete with cam-9800 Spring only Spring only Cam Pin

DELIVERY GRIPPER CHAINS Sold in a set of 1 Left hand & 1 Right hand 350, 360, 375, 9800 O.S., 385 N.S. 5/8” carrier link O.S. 1/2” carrier link new style 9800, 1 to 1 CD - 6” star wheels with tapes

P-362300 P-982300 P-362320 P-982320 P-1521 P-3002

54.90 70.00 29.90 49.90 8.20 6.90

P-361390 P-361100

159.90 159.90

P-981390

64.00

J ARMS For 9800 1 to 1 chain delivery safety guards

D I

••• Reinforced anvil is made of steel which prevents bowing and lasts longer.

GRIPPER BAR ASSEMBLY 350, 360 Complete 375, (9800 standard) Complete 9800 (1 to 1) 385 Complete (A) Gripper finger (B) Pin (for finger) (C) Anvil 350, 360 (C) Anvil 375, 9800 (universal) (C) Anvil 385 (D) Butterfly spring 350, 360 (D) Butterfly spring 375, 9800 (D) Butterfly spring 385 (E) Shoulder screw (F) Shaft 350, 360 (F) Shaft 375, 9800 (F) Shaft 385 (G) Shaft bearing (H) Cam ( I ) Stud (J) Lever 350,360,375,9800standard,385 (J) Lever 9800 (1 to 1) (K) Loop spring

P-360990 P-370990 P-980990 P-380990 P-361020 P-3001 P-361090 P-371090 P-381090 P-361070 P-371070 P-381070 P-8032 P-361060 P-371060 P-381060 P-361000 P-1416 P-401 P-361040 P-981040 P-361080

GRIPPER BAR REPAIR KIT ••• Comes with all parts (less anvil & shaft) to repair one gripper bar. 350, 360 P-30730 375, 9800 Std. & 1-1 P-30731 385 P-30732

240.00 219.60 240.00 999.80 11.00 .50 99.90 71.90 759.90 1.10 1.50 2.50 3.00 31.90 59.90 61.90 9.30 4.20 .60 38.80 22.00 .80

105.90 105.90 223.90

TAPE TRACK (18 inches) ••• Made of “sand paper like” material that holds better. For star wheels on 9800, 1 to 1 chain deliveries P-983130

1.50

Operators side - complete Arm only OS

P-984289 P-984290

30.00 22.90

Non-oper. side - complete Arm only NOS Cam Pin C-ring

P-984279 P-984280 P-1475 P-3012 P-679

30.00 22.90 5.40 .80 .60

INK WASH UP ATTACHMENT 350, 360 375

P-36773 P-37773

REPLACEMENT WASH UP BLADES 350, 360 (11-5/8 x 1-5/8) 4 holes 350, 360 (11-3/4 x 2-1/16) no holes 375 (12-7/8 x 1-5/8) 4 holes 9800 (13-1/4 x 2) 6 holes 9800XLK (13-1/4 x 2-1/16) 6 slots 9985 (14-3/32 x 1-5/8) 6-holes Century 3000 (14 x 1-5/16) 7 holes

195.00 199.90

P-5028 P-36767 P-5029 P-30200 P-30216 P-30225 P-30792

7.50 8.90 8.50 25.95 25.95 14.90 25.95

••• ELIMINATE COSTLY DOWNTIME WITH YOUR OWN EMERGENCY KIT FOR YOUR MODEL PRESS.

REPAIR KITS FOR ALL A.B. DICKS Master kit Junior kit Nut kit Washer kit Screw kit Ring kit Pin kit Spring kit

P-1707 P-5088 P-1701 P-1702 P-1703 P-1704 P-1705 P-1706

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

720 pcs. 437 pcs. 100 pcs. 120 pcs. 108 pcs. 228 pcs. 136 pcs. 28 pcs.

262.90 126.00 44.00 52.90 52.90 79.80 59.80 55.00

Replacement parts for : MULTI 1210, 1250OS, 1250W, 1250N, 1250DOM., 1215CD, PART # VARIABLE SPEED PULLEY 1250 O.S. - 1/2” Shaft P-1629 1250 N.S. - 5/8” Shaft P-1649

PART # COMPENSATING SUCKER TUBE ASSEMBLY EXTENDS 1/4” FURTHER. ••• Excellent for running envelopes and heavy stock. 1250 (Set of 2 w / block) P-12259 1250 (Tube only) P-12966 1850 (Set of 3 tubes only) P-18990 1870 (Set of 4 tubes only) P-18170

179.90 120.00

V-BELTS 35” Motor to printing head

P-4904

9.00

33” Pump to motor compound pulley

P-1689

7.50

32” Compound pulley to machine

P-1688

7.50

30” Compound pulley to machine

P-1686

6.50

26” To machine

P-4903

6.90

49” Conveyor drive

P-1690

8.00

34” New style pump to motor

P-1695

7.50

RATCHET PAWL ARM ASSEMBLY P-12979

FLAT DISC SUCKER FOOT

Complete (A) Nut (B) Ball retainer (C) Bracket (D) Screw (E) Washer (F) Sheet separator

D&E B A

P-12112 P-497 P-1105 P-12113 P-149 P-557 P-12114

.80

2.50

PAWL LEVER For single sheet feed 1330, 1360, 1650, 1860, 1960 P-13563

24.90

DRIVE LEVER ARM ASSEMBLY ••• Made of 1/4” solid cast stock for longer life and durability. 1250 P-12927 68.00 1330, 1360 P-13927 64.00 1650 P-16927 59.80 1850 P-18927 58.90

68.00

FEEDER LINKAGE DRIVE LEVER (near delivery) 29.90 .60 9.00 28.90 .60 .60 .90

SHEET SEPARATOR - 1360 P-13114

P-1552

SUCKER FOOT For Multilith 1218 & for Toko 4700, 4750 P-5203

SHEET SEPARATOR BRACKET ASSEMBLY F

107.90 32.00 103.80 136.00

P-12732

24.50

FEEDER PULLOUT ROLLER Roller with bearing P-12125 Bearing only P-1371 Spacer (on sides) P-12536 Spring P-12181

34.00 5.50 6.00 1.90

SPRING For feeder pullout roller P-12386

2.90

1.30 UPPER FEED ROLL HOLDER

SHEET SEPARATOR For TOKO 1218

3.00

P-5065 P-12128 P-537 P-624 P-566 P-12164 P-668 P-586 P-653 P-12069 P-5285

82.90 59.90 2.90 .60 .60 9.90 .60 .60 1.00 2.60 3.90

Complete (A) Center blower (B) Thumb nut (C) Lockwasher (D) Washer (E) Bracket (F) Retaining ring (G) Washer (H) Spring washer (I) Valve stem (J) Hose - 27”

IMPROVED

HUB FOR P-13085 OSC ROLL

SUCKER TUBE - 1650 O-RING For sucker tube

1250 N.S. 1250 O.S.

CENTER BLOWER KIT

E J

P-128114

A D

P-12115 P-12274

16.50 29.90

HAND CRANK ASSEMBLY ••• Made of solid white brass which helps prevent stripping. Complete (A) Stud (B) Handle (C) Spring lock (inside) (D) Screw (E) Nut (F) Spring (G) Steel ball

P-12955 P-36962 P-36961 P-36959 P-874 P-492 P-12909 P-755

140.00 19.90 24.90 2.40 .60 .60 2.50 1.90

TABLE PAWL RELEASE LEVER P-13440

P-16174 P-5329

86.90

1250 1330, 1360, 1650

P-12969 P-13969

69.00 69.00

12.60 A

.60

(A) CONVEYOR DRIVE SPROCKETS - O.S. Front feed roller Rear feed rolller

SUCTION FEET Double stem Single stem

P-12170 P-12990

99.90 160.00

PILOT SCREW

P-12104

1.70

P-12555 P-12559

11.60 11.60

(B) TENSION SPROCKET P-12522

4.90

TENSION ROLLER

P-12425

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

14.00

2650, 2850, 4150, 4250, 1330, 1360, 1315CD, 1650, 1820, 1860, 1870, 1960 PART # CONVEYOR TIMING PULLEY - N.S. -Conveyor roller P-4242 CONVEYOR TIMING PULLEY - N.S. -Front feed roller P-4257 CONVEYOR DRIVE PULLEY - N.S. -Rear feed roller P-4258

PART #

80.00 30.00 20.00

SKID ROLLER ASSEMBLY Works with P-12359 shown below. A

C B

Narrow wheel 1250 P-12434 (A) Arm P-12436 (B) Roller P-12454 (C) C-ring P-680 Wide wheel 1850 P-18434 (A) Arm P-12436 (B) Roller P-12532 (C) C-ring P-680 (D) Bushing (comes with Roller P-12532) P-799 THUMB SCREW

P-311

SKID WHEEL HOLDER

P-12359

SKID ROLLER ASSEMBLY For old design skid wheels that Complete 1250 Arm only Wheel only Bushing (included w/ P-12532) C-ring

CONVEYOR PAPER RETAINER

GUIDE ASSEMBLY - 1360

59.90 44.90 14.90 .60 69.90 44.90 14.90 .60 1.80 .80

uses posts. P-12501 P-14492 P-12532 P-799 P-680

P-12433

P-13403

6.90

19.90

PAPER FEED FRAME LEVERS 1250 Old design (straight, no tab) 1250 O.S. & L.W. (straight, with tab) 1250 N & DOM. (bent, with tab) 1650 (straight) 1650 (bent)

P-12165 P-12156 P-12151 P-16156 P-16151

36.90 24.90 36.90 24.90 36.90

CAM LEVER 1250 1650

P-12155 P-16155

42.90 46.90

18.40

7.40

Special cloth for easier feeding P-4955

32.00

P-12924 P-191

FEELER FINGER PILOT SCREW

P-18527

14.80

P-12708

36.40

P-12141 P-3073

FEED FRAME ROLLER 1250 1330, 1360, 1650

P-12157 P-13157

65.70 76.00

5.50 .60

PAPER GUIDE SPRING - 1850 & 1860

TAPE BAR

402.60 15.00 35.90 .60 .60 .60 3.30 7.50 2.00 89.90 .60 89.90 1.90 1.60 .60 .90

SPECIAL MICRO ADJUSTING NUT & STOP For upper feed roll adjustment P-12135 11.50 ••• NO TOOL NEEDED FOR FAST & EASY ADJUSTMENT!

P-4957

PAPER GUIDE SPRING 1250 SCREW

P-13703 P-13483 P-13359 P-225 P-635 P-1811 P-1415 P-13497 P-7220 P-13492 P-18 P-13434 P-1807 P-11795 P-698 P-4788

69.90 59.90 14.90 1.80 .60

CONVEYOR FEED TAPES Regular plastic

REGISTER BAR ASSEMBLY (Complete) (A) Support rod (B) Register bar with scale (C) Screw (D) Lockwasher (E) Washer (comp. assm. takes 2) (F) Spacer (G) Adjusting block (comp. assm. takes 2) (H) Thumb screw (comp. assm. takes 3) ( I ) Skid roller and block assm. - short (J) Set screw (not shown) (K) Skid roller and block assm. - long (L) Thumb screw (M) Brass plug (short) (not shown) (N) Retaining ring (not shown) (O) Brass plug (long) for thumb screw “H”

12.90 4.90

FOUR FINGER SHAFT ASSEMBLY -Complete 1250 New style (pyramid cam - no notch) P-12393 -Complete 1250 Domestic (tear drop cam) P-12387 -Complete 1250 M / MG (notched pyramid cam & tear drop cam) P-12381 THREE FINGER SHAFT ASSEMBLY -Complete 1250 Old style P-12388 PAPER HOLD ATTACHMENT -Complete 1250

P-12840

156.00 110.90 120.00 83.90 239.90

IMPRESSION GRIPPER SHAFT & ARM ASS’Y. Complete P-12203 130.00 Arm assembly P-12207 89.90 Shaft only P-12205 28.90 Arm only P-12197 88.00 IMPRESSION CYLINDER ADJUSTING SEGMENT

EJECTOR PIN BAR - Universal for old & new style. 1250 (7 Pin) P-12249

69.90

P-12733

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

31.80

Replacement parts for : MULTI 1210, 1250OS, 1250W, 1250N, 1250DOM., 1215CD, PART # D

A B

PART #

IMPRESSION GRIPPER HOLDER ASSEMBLY Complete P-12182 (A) Finger O.S. P-12245 (A) Finger N.S. P-12237 (B) Holder P-12189 (C) Screw (not shown) P-12187 (D) Screw P-96 (E) Washer (not shown) P-586

39.90 5.50 15.00 29.90 1.00 .60 .60

BUSHING For impression cylinder adjustment 1850 Non-op. side P-18400

32.00

CYLINDER GEARS Master (plate) P-12313 Blanket P-12214 Impression P-12191

187.90 213.90 229.90

••• All gears are hardened for longer life.

BLANKET CYLINDER SHAFTS 1250 (.750 Dia.) 1250 (.010 Oversized dia.) 1330, 1360, 1650 (.1.125 Dia.) 1330, 1360, 1650 (.030 Oversized dia.) 1850 (1.125 Dia.) 1850 (.030 Oversized dia.)

P-12290 P-12302 P-13290 P-13302 P-18290 P-18302

64.90 89.90 177.90 177.90 219.90 325.00

CLAMP COMPLETE - Trail End (A) R.H. Bracket (B) Clamp (C) Special Nut (D) Retaining Ring (E) Spring (F) L.H. Bracket (G) Round Head Screw (H) Lockwasher (I) Pin Bar with Lever (J) Spring-Extension (K) Thumb Screw (L) Support (M) Flat Head Screw

P-13790 P-13377 P-13389 P-11991 P-666 P-13724 P-13379 P-194 P-623 P-13323 P-13309 P-11783 P-16357 P-652

191.00 12.50 84.50 3.10 .60 2.00 12.50 .60 .60 69.90 2.10 9.00 25.00 .60

CAM BAND - 1250 O.S. & N.S. For blanket cylinder

P-12178

80.00

MASTER CYLINDER ADJUSTING WRENCH 1250 1250 1360 1360 1960

O.S. N.S. (13” clamps) (16-1/2” clamps)

P-12266 P-12236 P-13266 P-13236 P-19236

MASTER CYLINDER CLAMP LOCK LINK 1330, 1360, 1650 P-13299

77.90 77.90 39.90 32.00 66.00

32.00 1250 (10 X 15) MASTER CYLINDER ASSEMBLIES

BLANKET CYLINDER CLAMP KIT Complete (Trailing 11x17) P-14258 (A) Screw P-12204 (B) Spring P-12390 (C) Pin bar P-12922 (D) Bracket P-14003 (E) Nut bar P-14004 (F) Screw P-12921

80.00 4.50 .90 31.00 9.80 8.00 1.00

MASTER CYLINDER UPGRADE KIT 1650

P-13385

220.00

Lead Edge - complete (A) Screw (B) Thumb screw (C) Nut (used on P-12788 only) (D) Nut (used on P-12790 only) (E) Handle (used on P-12790 only) (F) Screw (G) Pin bar (18 point*) (H) Clamp only - not sold alone (I) Adjusting screw (J) Taper pin (K) Nut (L) Stem (M) Retainer (used on P-12790 only) (N) Spring (used on P-12790 only)

P-12788 P-159 P-1095 P-1898 P-12796 P-12761 P-12770 P-12760 -----P-12812 P-421 P-497 P-12793 P-12797 P-12762

100.00 .60 6.00 3.30 16.00 14.00 1.90 24.90 ----41.00 .70 .60 12.50 17.90 2.90

ACTUATING TOOL For plate cylinder latch 1330, 1360, 1650

P-5888

49.90

IMPROVED ••• MADE OF ALLOY STEEL DIECAST FOR LONGER LIFE & GREATER DURABILITY.

MASTER CYLINDER HOLD DOWN BRACKET - 1360, 1650 P-13357

72.50

PIN BAR CLAMP Master cylinder (10 X 15) 18 Point - 10” long

P-12760

24.90

CLAMP Blanket cylinder 17 Point - 9-3/4” long

P-12922

31.00

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

2650, 2850, 4150, 4250, 1330, 1360, 1315CD, 1650, 1820, 1860, 1870, 1960 PART #

PART # (A) WATER DUCTOR PIVOT - 1250 N.S., LW (11X17)

3/8” Bore

P-12322

19.90

(A) WATER DUCTOR PIVOT - 1250 O.S. (10 X 15) B

7/16” Bore

P-12535

SCREW - O.S. & N.S.

P-84

PLASTIC BOTTLE RECEPTACLE VALVE P-12347 WATER FOUNTAIN HOSE 1250, 1850 O.S. (10-1/2”) P-1189 1850 N.S. (19”) P-1181

419.80 520.00 410.00 399.90 .60 52.90 36.00 50.00 3.00 14.90 .60 5.90 .60 23.00 16.00 18.00 .60 7.50 .60 1.20 6.00 3.50 6.00 .60 .60 .60 5.90 5.90 3.90 47.70 33.90 42.00 36.00 51.00 17.00 .60 .60 64.80 74.50 2.50

14.30 1.80 5.00

BOTTLE, CAP & ADAPTER 1250 N.S., 1360,1850,1962 (Bottle sits in black plastic receptacle on side of water frame) 1 Quart assembly 2 Quart assembly

P-1912 P-1921

18.00 59.80

BOTTLE, CAP & ADAPTER 1250 O.S. (Bottle sits directly in water fountain) 1 Quart assembly 2 Quart assembly

P-1911 P-1920

19.80 59.80

.60

(B) EQUALIZER PIVOT - 1330, 1360 P-13322

29.90

37.50

DRIVE DISC For water form roller P-12419 16-1/2” ANGULAR ADJUSTING CLAMP ASSEMBLY Complete (1250) P-12702 Complete (1360, 1650) P-13702 Sub assy. - items (A) - (CC) (1250) P-12717 Sub assy. - items (A) - (CC) (1360, 1650) P-13717 (A) Screw P-161 (B) Pin bar (tail) - 22 point (1250) P-12746 (B1) Pin bar (tail) - 11 point (1360, 1650) P-13746 (B2) Pin bar (tail) - 13 point (1360, 1650) P-13659 (C) Thumb screw P-1067 (D) Bracket P-12729 (E) Lockwasher P-624 (F) Collar P-927 (G) Set screw P-3 (H) Shaft P-12726 ( I) Lateral adjusting block P-12736 (J) Adjusting block P-12734 (K) Retaining ring P-664 (L) Adjusting wheel P-12744 (M) Washer P-1887 (N) Spring washer P-650 (O) Shoulder screw P-8090 (P) Pointer P-12745 (Q) Spacer cam P-1402 (R) Screw P-172 (S) Screw P-191 (T) Lockwasher P-623 (U) Retainer P-12738 (V) Shoulder screw P-8089 (W) Spring P-12724 (X) Bracket (1250) P-12716 (Y) Lead retainer P-12751 (Z) Pin bar - (lead) - 22 point (1250) P-12739 (Z1) Pin bar - (lead) - 13 point (1360, 1650) P-13739 (Z2) Pin bar - (lead) - 11 point (1360, 1650) P-13652 (AA) Clip nut P-12749 (BB) Screw P-10323 (CC) Set screw P-1089 (DD) Shelf P-12705 (DD) Shelf (1360, 1650) P-13705 (EE) Screw P-12375

29.90

14.90

PIN ASSEMBLY For water fountain roller Short 1-7/8” shaft Medium 2-1/8” shaft Long 3-3/16” shaft

P-12688 P-12687 P-12691

COLLAR (For pin assembly listed above) 1/2” for short pin P-12371 7/8” for long/medium pin P-12370

20.50 12.00

SHAFT For water fountain roller P-12402

14.00

DRIVE COLLAR For Water fountain roller ••• Made of steel for longer life. For non-operators side P-12417

12.50

SCREW

P-840

PAWL - Water / Ink ratchet P-12268 (A) 1250

PAWL - Water / Ink ratchet (B) 1330, 1360, 1650, 1850, 1960 P-13268 D

B C E

9.90 9.90 9.90

5.90 16.00

34.90

RETAINER For water oscillating roller (A) Hex cap nut (B) Thumb nut (C) Spring (D) Retainer (E) Stud (stem)

P-470 P-538 P-12413 P-12560 P-7053

.60 2.20 1.50 13.00 9.90

BEARINGS For “Multi Flow” Water oscillator. Operators side Non-operators side

P-5770 P-5775

25.50 32.50

BEARING SHIELD (need 2) For lower ink form roller on 1820 second color head P-1820000 6.00 FORM ROLLER KNOBS Upper ink form Lower ink form Water form

P-12489 P-12491 P-12405

SET SCREW (all knobs)

P-8

SEPARATING CAM For ink form roller 1250 O.S. (10 X 15) P-12864 1250 N.S. (11 X 17) P-12451 TAPER PIN O.S. P-441 TAPER PIN N.S. P-439

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

29.90 29.90 36.90 .60

39.90 6.40 .60 .60

Replacement parts for : MULTI 1210, 1250OS, 1250W, 1250N, 1250DOM., 1215CD, PART # INK IDLER GEAR - Bushing included 1250 O.S. (10 X 15) P-12455 1250 N.S. (11 X 17) P-12446 BUSHING

P-1236

PART #

34.00 32.50

COMPOUND PULLEY

P-4259

65.00

P-13593

5.80

P-14001 P-18001 P-12587 P-18587 P-12593 P-12591 P-5061 P-12617 P-18617 P-7069

259.90 259.90 119.90 119.90 59.90 3.10 2.00 72.90 72.90 6.90

1250 O.S., W, LW (10 X 15 & 11 X 17)

P-12773

256.00

WASH UP BLADE *Fits our wash up attachment only.

P-5030

1.60 CLUTCH WEIGHT - 1360

INK IDLER GEAR - Does not use bushing. 1360, 1650 A

P-13457

72.00

DOG For oscillating rollers (A) Water P-12428 (B) Ink P-12463

27.40 32.00

WORM For ink & water oscillating rollers P-12464 HOLD DOWN SCREW P-12494

45.90 1.60

IDLER ROLLER BUSHING - 1650 P-11411 ROLLER SUPPORT 1330, 1360

P-13915

INK & WATER DUCTOR ARM 1250 N.S. (steel) P-12321 INK & WATER DUCTOR LATCH 1250 N.S. P-12338

3.80

10.50

5.50

1) INK & WATER DUCTOR ARM 1250 O.S. (Brass) P-12607

30.00

2) INK DUCTOR LATCH No bend 1250 O.S. (LH. & R.H.) P-12546 1850 P-18546

8.00 14.90

3) INK DUCTOR LATCH - With bend 1250 W (R.H.) P-14546 1250 W (L.H.) P-14338

9.90 9.90

4 5

4) RIGHT HAND SPRING - Ink & water ductor latch 1250 O.S. (10 X 15) P-12575 3.90 1250 N.S. (11 X 17) P-12336 1.70 5) LEFT HAND SPRING - Ink & water ductor latch 1250 O.S. (10 X 15) P-12551 1250 N.S. (11 X 17) P-12331 INK & WATER RATCHET WHEEL 1250, 1850 P-12239 1960 P-19239 SNUBBER - Ink & water ratchet lever P-7058

Complete 1250 Complete 1850 (A) Pulley only 1250 (A) Pulley only 1850 (B) Clutch shoe (set of 4) (C) Spring (D) Liner (E) Clutch drum 1250 (E) Clutch drum 1850 (F) Pilot screw

24.90

CLUTCH PULLEY ASSEMBLY

INK WASH UP ATTACHMENT ••• Universal for old & new style.

4.00 1.50

29.90 57.50 7.50

OLD STYLE DRIVE SHAFT ASSEMBLY Complete (A) Pinion gear - (black-stamped “O”) (B) Taper pin (C) Drive shaft

P-12835 P-12854 P-435 P-12869

128.00 34.00 .80 94.90

Complete (A) Pinion gear - (silver) (B) Taper pin (C) Drive shaft (only)

P-12837 P-12865 P-435 P-12869

128.00 34.00 .80 94.90

PILOT SCREW For pulley - both styles

P-8068

Complete (A) New style gear (B) Taper pin (C) Drive shaft

P-12577 P-12581 P-435 P-12583

PILOT SCREW For pulley

P-8067

INK FOUNTAIN BLADE 1650 1960 Blade 1850 only

DRIVE SHAFT ASSEMBLY - 1360, 1650 Complete (A) Pinion gear (B) Taper pin (C) Drive shaft

P-13837 P-13581 P-435 P-13869

108.00 99.90 69.90

5.90

INK FOUNTAIN ASSEMBLY - 1250 O.S. & N.S. ••• Designed with replaceable end caps & deeper well for 50% more ink capacity. Complete P-12778 319.80 Fountain only P-12789 180.00 Thumb screw (14 total) P-1570 6.00 Wire P-35084 2.50 Clamp P-12082 30.00 Screw for clamp P-12907 3.40 Blade 1250 (10-1/4” X 1-3/4”) P-12079 44.00 Blade 1250 (10-1/4” X 3”) P-12233 70.00 P-16233 P-19079 P-18079

9.90

NEW STYLE DRIVE SHAFT ASSEMBLY With long shank gear. For use with hardened cylinder gears.

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

102.00 32.00 .80 69.00 5.90 189.90 24.90 .80 172.00

2650, 2850, 4150, 4250, 1330, 1360, 1315CD, 1650, 1820, 1860, 1870, 1960 PART #

SWITCH ASSEMBLY Complete Start (green) 1250 N.S. Stop (red) 1250 N.S.

PART #

P-12566 P-12829 P-4062

189.90 55.00 58.90

SWITCH REPLACEMENT KIT 1330, 1360 Consists of: 1 ea. stop switch (red) & start switch (green), 1 mounting plate, 2 switch holders, 10 wire terminals. Also includes installation instructions. P-9828

109.80

ALTERNATE ACTION SWITCH 1960 P-4060

72.50

PUMP SWITCH 1330, 1360

P-4470

GRIPPER BAR CHAINS 1250 (53-3/4” long X 1/2” wide) 1850 (54-1/4” long X 1/2” wide) Carrier link - 1250, 1850

P-121100 P-181100 P-9406

26.90 34.90 4.50

For Press Specialties chain delivery - N.S. (51-1/4” long X 1/2” wide)

P-8944

66.00

For Press Specialties chain delivery - O.S. (50-3/4” long X 7/16” wide)

P-8933

78.00

Gripper chain - TOKO 1218 Carrier link - TOKO 1218

P-8971 P-8736

38.00 18.90

24.90 I

(1) TOGGLE SWITCH For drive motor & pump (includes screws) 1250 O.S. P-12305

77.90 .60

(2) MOMENTARY TOGGLE SWITCH 1250 L.W. P-4056

30.00

COUNTER With bracket & arm With bracket & no arm Counter only 1250N, 1360

P-12996 P-12954 P-12952

124.90 99.90 169.90

COUNTER ARM ONLY

P-12942

29.90

A E B

I D

“QUICK CHANGE” UPPER EJECTOR ROLLER ASSEMBLY ••• Adjustable, gear driven with a knurled shaft for quick removal and easy access. P-12616 P-12558 P-12604 P-12584 P-12612 P-12600 P-1444 P-12611 P-12621 P-12782 P-12590 P-12618

314.90 128.00 1.60 29.90 38.00 29.90 4.20 38.00 16.00 75.00 9.90 4.90

STRIPPER FINGER - 1650 CD (1615) P-162281

P-181590

GRIPPER BAR ASSEMBLY (WITH BRASS COLORED ANVIL Complete 1250 Complete 1330, 1360 Complete 1850 Complete 1960 (A) Finger (B) Screw (C) Holder (D) Spring (E) Anvil only 1250 (E) Anvil only 1330, 1360 (E) Anvil only 1850 (E) Anvil only 1960 (F) Screw (G) Locking collar (H) Shaft assembly 1250, 1330, 1360 (H) Shaft assembly 1850 ( I ) Stud (J ) Nut (K) Cam roller

P-120990 P-130990 P-180990 P-190990 P-121020 P-12187 P-121061 P-121080 P-121090 P-131090 P-181090 P-191090 P-44 P-734 P-121010 P-181010 P-4600 P-522 P-1447

340.00 350.00 490.00 600.00 1.10 1.00 14.00 1.00 134.00 199.90 269.90 376.00 .60 10.70 69.90 79.90 5.00 .60 6.90

1250, 1360

P-30733

105.90

GRIPPER BAR REPAIR KITS For Press Specialties Consists of the most commonly replaceable parts on your gripper bar assembly. (Less anvil & shaft where noted) 1217 (4 finger)* 1217, 1250 (5 finger)* 1250 (4 finger)** 1252 *

P-30745 P-30746 P-30747 P-30748

248.00 248.00 248.00 248.00

* does not come with shaft or anvil. ** comes with shaft but no anvil. ••• ELIMINATE COSTLY DOWNTIME WITH YOUR OWN EMERGENCY KIT FOR YOUR MODEL PRESS.

REPAIR KITS FOR ALL MULTILITHS 5.90

BACK JOGGER LEVER ASSEMBLY 1850 CD (1815)

GRIPPER BAR REPAIR KIT Consists of the most commonly replaceable parts on your gripper bar assembly. (Less anvil & shaft) For Multilith style gripper bars only

H F

Complete 1250 N.S. (A) Rod assembly (B) Spring (C) Arm assembly L.H. & R.H. (D) Arm assembly R.H. (E) Roll assembly (F) Roller (G) Arm assembly L.H. (H) Roller (I) Shaft & gear assembly (J ) Wheel (K)Spring

••• MADE OF YELLOW BRASS FOR HIGHER TENSIL STRENGTH.

WIRE MOUNTING SCREWS For P-12305 1250 O.S. P-252 2

59.90

Master kit Junior kit Nut kit Screw kit Pin kit Spring kit Washer & ring kit

P-1776 - 435 pcs. P-30328 - 217 pcs. P-1772 - 60 pcs. P-1773 - 62 pcs. P-1774 - 86 pcs. P-1775 - 85 pcs. P-1777 - 136 pcs.

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

359.80 199.90 44.80 159.80 52.90 139.80 63.90

Replacement parts for: RYOBI 2700, 2800, 3200, 3200AN/CD/NP, 3302M, 480/520/560 PART # 1

PART #

1) FILTER FELT

P-30201

4.00

2) GASKET SEAL

P-1937

6.70

3) WICK For oil jar

P-1155

1.50

SUCKER FEET Standard P-5208 .80 ••• Treated with ink resistant repellent for less ink tracking. SUCKER FEET

PUMP REPAIR KIT - 2700, 2800, 3200 P-31120 Consists of: 4 Vanes / 2 Filters / 1 Oil wick / 2 Ball bearings / 1 Oil seal

329.90

PUMP REPAIR KIT - 520/522/530/560 P-31130 319.90 Consists of: 4 Vanes / 2 Filters / 2 Ball bearings / 1 Urethane gasket / 1 Fiber gasket / 8 Paper gaskets / 2 Timing belts (Only one of each item depicted here) PUMP VANE ••• MADE OF “GROUND STAINLESS STEEL” (27.5 mm x 115 mm) P-9448

34.90

VARIABLE SPEED PULLEY P-1491

249.90

SPEED CONTROL & FEEDER HAND CRANK ••• Improved style works on 2700, 2800, 3200.

HOSE For side blowers For compressor filter For rear blower For sucker tube manifold

A&B

C 31.90

P-5265 P-5299 P-5288 P-1188

4.90 11.20 7.00 6.00

P-27087 P-32087 P-2652

24.40 24.40 9.90

SHEET SEPARATOR Brass Copper

P-27114 P-27117

1.00 1.20

SHEET SEPARATORS (A) 522 (B) 522PF / PFH

P-522114 P-522114PF

3.00 10.90

4.20 8.90

P-97471 P-33478 P-33471

6.50 10.90 14.00

BACK PAPER GUIDE ASSEMBLY 2700, 2800, 3200, 3200MCD COMPLETE P-27081 (A) Screw w/ sems washer P-2328 (B) Block P-27221 (C) Bracket P-27090 (D) Back guide spring P-27712 (E) Screw P-2327

71.90 .60 10.80 34.90 25.80 .60

SPRING BASE For P-27088 shown below.

2 FEEDER CLAMP 5.5 mm slide plate slots 7 mm slide plate slots ADJUSTING SCREW

7.00 4.60

GUIDE SPRING 975 PFA (Thick) (Thin)

P-98060

P-5241 P-7580

THUMB SCREW For sheet separator bracket P-2909 THUMB SCREW For master cylinder tail clamp 2700, 2800, 3200 P-2903

69.90

TIMING BELT - For main pump 520, 522, 530, 560 P-3811

(A) 500K, 512 (B) 480N, 480K

P-27100

33.90

1) BACK PAPER GUIDE

P-27537

9.90

2) SIDE PAPER GUIDE

P-27088

10.50

PAPER RETAINER - 3302 Located under upper feed roller. P-33143

26.90

PAPER GUIDE HANDLE STOPPER 950, 960 P-95124

14.90

P-33500 P-33420 P-33433

22.50 23.90 22.50

slide thickness SLIDE PLATE For feeder clamp 5 mm slide thickness 6.5 mm slide thickness

P-27089 P-32089

SLIDE PLATE & FEEDER CLAMP KIT P-39087

BUMPER For air control latch P-5283

49.90 56.90

83.80

3.20

HEIGHT CONTROL SCREW - For paper leveling bar. P-8144 15.90

COUPLING JOINT

P-6776

12.10

SUCKER TUBE

P-27174

12.50

SCREW HOLDER

P-27966

9.10

PAPER RETAINER Feeder 3302 Conveyor .008 thick Conveyor .012 thick

FEED TAPES (sold individually—not in sets) 480K/N, 500N/NP P-3935 3302 s/n up to 4432 P-3939 3302 s/n 4433 to 7036 P-3936 3302 s/n 7037 & Up P-3870

39.90 32.00 32.00 39.90

FEED SENSING SWITCH R-3302, I-3985

29.90

P-4050

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

ITEK 530, 560, 950, 960, 975.....................................................Continued thru page 16. PART # C A D

FEELER FINGER SHAFT Complete 2700, 2800 Complete 3200 (A) Shaft only 2700, 2800 (A) Shaft only 3200 (B) Lever (C) Latch (D) Roll pin

RUBBER FEED ROLLERS 2700, 2800 3200

2 1

P-27138 P-32138 P-27139 P-32139 P-27719 P-27141 P-2834

P-27157 P-32157

PART #

P-27245 P-33245

8.00 14.90

PAPER STOP FINGER 1) 2700, 2800 2) 3302

P-27241 P-33241

6.00 9.90

P-33237

19.00

SKID ROLLER ASSEMBLY - 3302 Operators side (shown) P-33562 Non-operators side P-33568

134.90 134.90

SPRING - Imp. cyl. latch

P-27791

ADJUSTING NUT For blanket cylinder clamps Right hand thread P-5303 Left hand thread P-5312

P-27327

9.90

LATERAL ADJUSTING SCREW For head clamp P-2917 13.90 SPRING (Plate Cylinder)

P-33365

4.90

P-27323 P-32323 P-32333 P-33323

105.80 116.90 110.00 97.50

179.90 179.90

IMP. GRIPPER FINGER 1) 2700, 2800, 3200 2) 3302 (urethane tip)

FEED DRUM FINGER (urethane tip)

TAIL CLAMP SPRING

99.90 169.90 62.90 115.90 19.00 29.90 .60

9.50

25.80 25.80

TAIL CLAMP 2700, 2800 3200 CD/NP 3200 17-1/4” IMAGE 3302

LOCK PIN on Plate CylinderP-4543

29.90

HEAD CLAMPS For Ryobi 3302 ••• DIAMOND COATED FOR SURE GRIP AND LONGER LIFE. Top bar (shown) P-33788 Short clamp (Operators side) P-33771 Short clamp (Non-operators side) P-33760 PIN For P-33788 shown above. Ser. # 6186 & lower (3mm small O.D.) Ser. # 6187 & higher (5mm small O.D.)

P-4773 P-4789

490.00 162.50 162.50

7.00 4.90

WATER CONTROL LEVER A

3200 MCD

P-320416

32.00

B C

WAVER ROLLER TENSION SPRING P-38413

STANDARD BLANKET BARS 2700, 2800 Complete R-3200, I-975 Complete R-3302, I-3985 (A) Upper blanket bar 2700, 2800 (A) Upper blanket bar R-3200, I-975 (A) Upper blanket bar R-3302, I-3985 (B) Lower blanket bar 2700, 2800 (B) Lower blanket bar R-3200, I-975 (B) Lower blanket bars R-3302, I-3985 (C) Mounting screw (D) Clamping screw

P-27252 P-32252 P-33252 P-27258 P-32258 P-33258 P-27256 P-32256 P-33256 P-2216 P-2206

220.00 222.00 167.90 71.90 54.00 82.00 65.90 62.00 78.90 .60 .60

WATER OSCILLATOR SHAFT ASSEMBLY - 2700, 2800 Complete P-27460 Shaft only P-27460-S Dog P-27463 Worm P-27464 Roll pin P-382 SPLASH GUARD SHIELD P-27376 SPLASH GUARD KIT P-27376-K Consists of 2 shields plus hardware.

QUICK CHANGE BLANKET BARS ••• Bars remain on your cylinder while you make a 5 minute blanket change. Closed cylinder 1/2” gap (19” blanket size) 950, 960 / 2700, 2800 Open cylinder 4” gap (19-1/2” blanket size) 2700XL, 2800XL 975 / 3200 985 / 3200 MCD 975 / 3200XL,XLD,CPD 3985 / 3302

P-30310

210.00

P-30047 P-30037 P-30038 P-30311 P-30221

341.25 193.05 209.65 341.25 390.00

4.90

299.90 184.90 44.00 63.80 .60 3.00 22.90

WATER BOTTLE STOP SPRING for cap assy.

P-7621 P-27543

8.20 4.90

BEARING HOUSING

P-27322

66.90

WATER DUCTOR LATCH 2700, 2800

P-27546

6.00

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

Replacement parts for: RYOBI / ITEK...................................Continued from page 13. PART #

PART # ADJUSTING SCREW For ink fountain R-2700, 2800, 3200, 3302

WATER FOUNTAIN ROLLERS 2700 3200

P-27364 P-32364

P-2925

7.00

204.00 390.00

OSCILLATING SHAFT ASSEMBLY - INK 2700 INK WASH UP BLADE 950, 960, 2800 - 30.3 cm Long (6 Holes) 3200, 3302, 3985 - 35.9 cm Long (6 Holes)

P-30224 P-30225

14.90 14.90

INK FOUNTAIN BLADES 2700, 950 - 29.5 cm x 9.0 cm (Ser.16331 & up) 2700, 950 - 28.6 cm x 7.0 cm (Ser.16330 & down) 3200 CD/NP - 32.0 cm x 9.0 cm 3200 MCD/MNP- 34.6 cm x 9.0 cm 500N / NP - 49.2 cm x 85.7 cm

P-27233 P-95233 P-32233 P-32233M P-50079NP

77.90 82.90 89.90 86.00 79.00

Complete Shaft only Roll pin Dog (comes with P-27249) Worm (comes with P-27249)

P-27462 P-27472 P-2834 P-27463 P-28464

204.90 73.80 .60 44.00 63.80

Dog & Worm set

P-27249

94.00

DOG & WORM KIT DOG (Ink & Water 950, 2700) WORM (Ink & Water 950, 2700)

P-27874 P-27463 P-27464

94.00 44.00 63.80

DOG (Ink & Water 960, 2800) WORM (Ink 960, 2800) WORM (Water 960, 2800)

P-27463 P-27464 P-28464

44.00 63.80 63.80

BUSHING For ink oscillating roller P-3203

14.00

KEY For drive shaft clutch pulley P-11652

2.00

WASH UP TRAY ASSEMBLY 2700/2800 3200/3202 3302

INK FOUNTAIN WIRE 950, 960, 2700, 2800 3200, 3302

P-27773 P-32773 P-33773

219.90 169.90 289.90

P-37084 P-32084

2.90 1.70

BUSHING For ink fountain roller P-3268

INK IDLER GEAR

9.90

DRIVE SHAFT AND GEAR ASSEMBLY Complete 2700, 2800 Complete 3200 Complete 3302 Shaft only 2700, 2800 Shaft only 3200 Shaft only 960PFA, 3200PFA Shaft only 3302 Gear only 2700, 2800, 3200 (not 3200PFA) Gear only 3302 Taper pin 2700, 2800, 3200 Taper pin 3302

P-27577 P-32577 P-33577 P-27583 P-32583 P-32583PFA P-33583 P-27581 P-33581 P-451 P-2849

289.90 340.00 243.90 143.90 170.00 199.90 110.00 104.90 110.00 .60 2.00

P-27509

144.90

(A) I-950/960

P-95607

43.90

COUNTER

P-27954

129.00

(B) R-27/28/3200 Sers.

P-27607

43.90

INK DUCTOR SPRINGS Operators side Non-operators side

Screw Washer Arm

P-2521 P-2700 P-27956

.60 .60 26.00

P-27338 P-27336

3.50 2.40

IDLER GEARS On ejector roller

P-27636

57.90

INK RATCHET PAWL

P-27268

39.80

P-27629

57.90

INK DUCTOR ARMS

BUSHING For idler rollers

P-3207

24.90

For C/D drive sprocket shaft

GEAR STUD For Chain Delivery drive gear P-7939

16.00

ADJUSTING SCREW For ink fountain ITEK 950, 960

P-2021

5.20

SWITCH BODY For control panel R-3302, I-3985

P-9830

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

39.90

Replacement parts for: RYOBI / ITEK...................................Continued from page 13. PART #

PART #

OFFSET DUPLICATOR LAMP (Long neck) 950, 960, 2700, 2800

P-9865

99.80

Lamp comes with plug and can be plugged into any standard 115v wall outlet. Some models of Ryobi may need lamp wired directly to press.

GUIDE

P-272281

22.00

FRONT GUIDE

P-272420

83.90

••• CAN USE UP TO 100 WATT BULB. LED LAMP - On sub control box. R-3302, I-3985 P-9707

30.00

DELIVERY TABLE SENSING SWITCH R-3200, I-975

CARRIER LINK For gripper bar

P-8738

14.00

GRIPPER CHAIN (1 only) 59” long P-8939 100.00 54” long P-8938 160.00 NOTE: Please measure your chains end to end. Chain connecting link

P-1540

2.90

P-8745

22.50

CONNECTING LINK R-3302, 3304 / I-3985

E F

O&P&Q N

T L

GRIPPER BAR ASSEMBLY Complete 2700, 2800 Complete 3200 Complete 3302

P-270990 P-320990 P-330990

439.90 399.90 495.00

(A) (B1) (B2) (C) (D) (E) (F) (F) (G) (G) (H) (I) (J) (J) (K) (L) (M) (N) (O) (P) (Q) (R) (S) (T) (T) (U)

P-320991 P-2810 P-2805 P-271040 P-2832 P-2103 P-271020 P-331020 P-281080 P-331080 P-2511 P-1487 P-271060 P-321060 P-271092 P-320992 P-1803 P-2752 P-2702 P-2602 P-7920 P-2833 P-271061 P-271091 P-321091 P-11435

52.90 .90 .60 29.90 .60 .60 11.50 38.85 2.30 2.90 .60 9.90 12.40 10.90 21.90 52.90 6.50 .60 .60 .60 6.30 .60 6.40 31.90 34.90 5.70

Right hand bracket Taper pin Taper pin Gripper arm Roll pin Screw Gripper finger (no urethane) Gripper finger (urethane tip) Spring (2 on 2700, 2800, 3200) Spring (4 on 3302) Set screw Collar Gripper finger shaft - 2700, 2800 Gripper finger shaft - 3200 Center bracket Left hand bracket Ball bearing C-Ring Lockwasher Nut Stud Roll pin Gripper pad Shaft - 2700, 2800 Shaft - 3200 Collar

P-9815

V-BELT For Ryobi / Itek For compressor P-1678 For clutch pulley P-1687 Motor to pump P-1695 Motor to pump 3202M P-4905 Motor to pump 950, 960 P-4907 Drive motor 3200 (60Hz) P-4910 Drive motor 3200 (50Hz) P-4986 ••• All sizes available 2L, 3L, 4L, 5L DOLLY BOARD Complete Board only Caster Washer Screw

18.90

(28”) (31”) (34”) (36”) (38”) (42”) (41”)

8.00 8.00 7.50 9.90 9.00 10.50 16.00

ASSEMBLY - RYOBI 3302 P-332440 214.00 P-332500 174.50 P-1641-S 19.90 P-569 .60 P-10342 .60

••• Eliminate costly downtime with your own emergency kit for your model press. (Master Kit does not include Spring Kit) REPAIR KITS FOR RYOBI Master kit P-30376 - 513 pcs 239.80 Pin kit P-30375 - 168 pcs. 99.90 Ring kit P-30374 - 104 pcs. 55.80 Nut kit P-30373 - 38 pcs. 21.80 Washer kit P-30372 - 68 pcs. 49.90 Screw kit P-30371 - 132 pcs. 77.90 Spring kit P-31128 - 39 pcs. 129.90

• • • • • • • • • PARTS FOR ITEK • • • • • • • • GEAR- For 1015/1117 Plate Maker Tank roller frame ass’y.

P-1015010

7.50

GEAR- For 1015/1117 Plate Maker Tank roller frame ass’y.

P-1015020

7.50

GEAR- For 1015/1117 Plate Maker Tank roller frame ass’y.

P-1015030

7.50

GEAR- For 1015/1117 Plate Maker Tank roller frame ass’y.

P-1015040

8.70

GEAR- For 1015/1117 Plate Maker Tank roller frame ass’y.

P-1015050

7.00

SPRING- For 1015/1117 Plate Maker Tension rollers

P-1015200

3.90

BACK STOP BRACKET (Chain Delivery) 2700, 2800, 3200

P-272422

29.90

SPRING- For 1015/1117 Plate Maker Tension rollers

P-1015210

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

6.90

Replacement parts for: TOWNSEND-51 second color heads PART #

T-WRENCH

T-1132

27.90

END BELL Small Large with hole for dog

T-1807 T-4806

33.50 35.90

DRIVE PULLEY

T-22444

79.90

TIMING BELT For the AB Dick series P-1654

12.90

PINION GEAR

T-24435

46.90

LOCKING SCREW For 1250W & LW T-1116

11.90

MICRO SCREW

T-7153

19.90

DOG 1250 O.S., 350, 360, O.S. 1250 N.S., 350, 360, N.S. WORM

T-1804 T-4804 T-1802

29.90 29.90 29.90

(Ink oscillator) AB Dick 9800 (Small ink oscillator) Multilith 1250 (Small ink oscillator) AB Dick 350, 360 Torsion rod for cylinder assembly - Ryobi 2700, 2800 / Itek 950, 960

TRANSFER DRIVE GEAR

T-22433

54.90

RATCHET PAWL Ink (oper. side) Spring (oper. side) Water (non-oper. side) Spring (non-oper. side)

T-1570 T-1572 T-1571 T-1573

14.00 3.90 14.00 3.90

DUCTOR ARM Ink & water T-1503

21.00

LATCH Ink & water 10.50

INK RATCHET DRIVE ARM Fits all models T-1551

INK & WATER HOLD DOWN ASSEMBLY Small - water for AB Dick 350, 360 N.S. L.H. T-4858 R.H. T-4857 Large - ink for Multilith 1250 N.S., 350, 360 N.S. L.H. T-2855 R.H. T-2856

SHAFT SHAFT SHAFT SHAFT

PART #

T-1504

DUCTOR LATCH SPRING Ink & water Non-oper. side (L.H.) P-12575 Oper. side (R.H.) P-12551

6.50 3.90 4.00

FORM ROLLER DRIVE GEAR & PINION ASSEMBLY 1250 Old style (10 X 15) T-1407 62.90 1250 Old style (11 X 17) T-2407 66.90 1250 New style (11 X 17) T-4407 77.90 360, 375, 9800 T-8407 77.90 Drive pinion only (comes with gear but is sold separately) T-1403 33.90

INK FOUNTAIN BLADE For Ryobi 2800, AB Dick 350, 360, Chief 15, 17 Screw (need 5)

T-2627 P-120

22.00 .60

OSCILLATING ROLLER TUBE 39.90 39.90 34.90 36.00

T-19801 T-1801 T-2801

27.90 36.90 22.60

T-18119

25.90

COLLAR ASSEMBLY Water bottle Complete T-3643 Collar only T-3637 Thumb screw P-309

9.00 9.00 .60

HOSE Water fountain TUBE CONTROL VALVE

P-1189 P-11934

1.80 3.00

DRIVER ASSEMBLY Complete Clutch only One way clutch bearing

T-20652 T-20653 P-5800

54.90 34.90 29.90

AB Dick 350, 360, Multilith 1250 N.S. (Large ink) T-2810 (Small ink) T-2811 AB Dick 350, 360 O.S. Complete ass’y. (small ink) T-2824 AB Dick 9800 O.S. & NS. & Multilith 1330, 1360 T-18811 Chief 15, 17 (Small ink) T-12811 Multilith 1250 O.S. (Small ink) T-1811

EQUALIZER BAR For ink & water ductor AB Dick 350, 360, Ryobi 2700, 2800, Multilith 1250 N.S., Chief 15 P-15340

129.90 119.90 299.90 117.90 149.90 139.90

24.90

MICRO CLAMP 1-3/16” O.A.L. 7/8” O.A.L.

T-7151 T-4176

27.90 57.00

KNOB For water fountain roller

T-22611

13.90

CYLINDER BRACKET LOCK SCREW For TRANSFER BUSHING ASSEMBLY Ryobi, M-1250, A-9800 T-7827 Multi T-1827 A-9800 (Geared trans.) T-19824 A-9800 (Non-geared) T-19827

34.90 35.90 34.90 34.90

A.B. Dick 350/360 N.S., 8800, 375, 9800, 385 Multi 1250LW, 1330, 1360, 1850 Ryobi/Itek 2700, 2800, 3200, 950, 960, 975 T-9719

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

8.30

Replacement parts for: HAMADA 500CDA, 600CD, 600AT, 601CD/QT, 602CD/QT, 611, PART # PUMP VANE

P-9446

PART # 26.20

PUMP REPAIR KIT P-31125 Consists of: 8 Vanes - #P-9446 / 4 Bearings - #P-790 / 1 Bottle of pump oil - #P-1588 V-BELTS For Hamada For compressor (115V, 50/60 Hz) P-1680 (27”) For compound pulley to machine P-1686 (30”) Intermediate P-4930 (36”) Drive shaft (60 Hz) P-1678 (28”) Main drive P-4933 (39”) Main drive P-4934 (38”) Main drive P-5457 (37”) ••• All sizes available 2L, 3L, 4L, 5L

P-55113

548.00

BUSHING For rotary valve flange. P-3275

17.80

16.00

THUMB SCREW For sheet separator holder

6.00 6.50 12.50 8.00 12.50 12.50 11.90

P-9350

P-5207 P-5205 P-5206 P-7575

.90

BRACKET For sheet separator holder

P-2900

5.20

TABLE RAISE HANDLE ASSEMBLY ••• MADE WITH DURABLE WHITE BRASS

ED IMPROV

SUCKER FOOT (A) Standard (500, 700) (B) Heavy (500, 700) (C) For 611, 248, 234 Duetto, E47 (D) Hamada Bellows

P-12114

249.90

SPEED PULLEY

SHEET SEPARATOR

FOR LONGER LIFE & DURABILITY.

A&B

Complete (A) Screw (B) Nut (C) Ball (inside) (D) Spring (inside E) (E) Handle (F) Shaft (G) Spring lock

BLOCK For blower nozzle

2.60 2.00 2.20 2.25

P-12955 P-874 P-492 P-755 P-12909 P-36961 P-36962 P-36959

140.00 .60 .60 1.90 2.50 24.90 19.90 2.40

P-55164

11.90

SPRING For paper feed adjusting shaft P-55148

2.50

P-55782

24.90

SPRING For paper height bar 700 P-77711

3.70

(C&D not shown) HEIGHT CONTROL LEVER SUCKER FOOT HOLDER P-55174 For P-5207 / P-5205 Listed above.

7.00

FEED BRUSH

P-31170

14.90

FEEDER CLAMP

P-55049

28.80

P-66087

67.90

FEEDER CLAMP - 611, 612

CONVEYOR TAPE

P-1796

12.50

P-12433

19.90

CONVEYOR JOGGER BLOCK P-55200

9.90

PAPER RETAINER FEEDER PULLOUT ROLLER 500, 700 P-55125 600, 601, 602, 800 P-66125

SPRING For feed roll tire

P-55386

SLEEVE For inside of pullout roller bearing P-55384

21.55 90.00

2.90

18.00

BEARING ASSEMBLY For lower feed roller (500 PF)Only P-3201

28.90

BUSHING For lower feed roller 500, 600, 700, 800 P-3286

12.90

JOGGER CAM LINK

P-55443

19.90

SPRING For conveyor spring guide 800DX, SX

P-80496

2.50

FEED ADJ. KNOB

P-11541

12.90

STOP For adjusting nut

P-12606

6.00

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

612,700CD, 800DX/SX, 50/60/70/80..................................Continued thru page 20. PART # SHAFT For clutch pulley

FEELER FINGER

P-55141

18.90

12.90

P-55213 P-55406

IMPROVED

DOG & WORM (Water) P-55429 DOG (500, 600, 700) P-55428 WORM (Ink & water 500, 600, 700) P-55464 DOG (8MM Thick head) (Ink 500, 600, 700) P-55463 WORM (Ink & water 500, 600, 700) P-55464

60.00 29.90 43.90 29.00 43.90

•••Hardness density has been improved so that the dog and worm wear evenly.

SPRINGS For impression cylinder shaft (A) (B)

P-55614

PART #

5.00 3.20

INK DOG & WORM KIT

P-55874

59.80

Consists of dog, worm, and pin for worm. IMPRESSION GRIPPER FINGER

COUNTER ASSEMBLY

BLOCK For blanket bar

P-55245

3.90

P-55954

91.90

P-55922

DRIVE DOG (9MM Thick head) For second color unit P-5525463 29.90

WATER DUCTOR ARMS 14MM Bore (L.H.) 14MM Bore (R.H.) 12MM Bore (L.H.) 12MM Bore (R.H.)

P-7727607 P-7727321 P-5525607 P-5525321

32.00 32.00 31.90 44.00

P-55538

16.90

46.50 LATCH For form roll handle

BRACKET NUT For blanket cylinder. P-55361

69.00

FORM ROLLER DRIVE DISC 800DX / SX P-80419

FORM ROLLER HUB

(A)

(B) (C) (D)

SHAFT - Master cylinder gear lock. 500, 500CD 500CDA, 600CDA 700CD NUT For gear lock shaft. SHAFT KEY WRENCH

P-55411

SPRING Between ink form roller brackets P-55475 P-55180 P-66180 P-77180 P-55186 P-55182 P-5883

64.00 32.00 35.90 4.20 2.90 23.90

INK DUCTOR ARM

48.90

21.90

1.80

P-55572

16.90

P-55550

45.00

IDLER GEAR (BRASS) For night latch

P-55457

99.90

IDLER GEAR (STEEL) Contacts distributor roller

P-55446

69.90

DUCTOR ROLLER LATCH Ink P-55338 Water P-55546

5.20 5.80

DUCTOR ROLLER SPRINGS Non operators side P-55331 Operators side P-55336

2.40 2.40

DUCTOR SHAFT SPRINGS R.H. 500, 600, 700 P-55549 L.H. 500, 600, 700 P-55567

1.80 1.80

PILOT SCREW For ink & water ratchet P-6509

4.90

MASTER CYLINDER CLAMP ADJUSTMENT Thumb screw Thumb nut

P-2922 P-2942

14.80 15.60

DRIVE SHAFT GEAR

P-55581

61.90

WATER STOP

P-30220

GEAR For dampening form roller P-55046

4.40

72.00

WATER PAWL

P-55462

10.00

WATER PAWL SPRING

P-55267

1.20

EQUALIZER BAR For ink ductor assembly.

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

Replacement parts for HAMADA..........................................Continued from page 18. PART # K

G&H F

PART #

GRIPPER FINGER

P-551000

7.90

GRIPPER FINGER (with pin) GRIPPER FINGER (w/o pin)

P-801024 P-801025

29.50 23.20

A E GRIPPER BAR ASSEMBLY Complete 500CDA, 600 Complete 800DX, 800SX (A) Anvil (500CDA, 600) (A) Anvil (800) (B) Shaft (500CDA, 600) (B) Shaft (800) (C) Gripper spring (500 uses 4 / 800 uses 8) (D) Roll pin (500 uses 4 / 800 uses 8) (E) Gripper finger (500 uses 4, 800 uses 8) (F) Gripper tension spring (1 for 800 only) (G) Set screw (H) Collar (500 use 1 / 800 uses 3)

P-550990 P-800990 P-551090 P-801090 P-551060 P-801060 P-551080 P-2832 P-551000 P-771080 P-2506 P-6728

290.00 338.00 159.00 199.90 32.00 54.00 2.40 .60 7.90 2.00 .60 4.00

** Lever assembly (consists of items (I) - (P) (I) Gripper operating lever (J) Screw (K) Lockwasher (L) Nut (M) Lockwasher (N) Washer (O) Ball bearing (P) Shoulder screw

P-551040 P-551041 P-2107 P-2701 P-2602 P-631 P-2729 P-1803 P-8160

49.90 29.90 .60 .60 .60 .60 .60 6.50 7.90

GRIPPER BAR REPAIR KITS H-500CDA, 600 P-30741 240.00 Enough parts to rebuild 3 gripper bars. Consists of key #’s: C (qty. 12), D (qty. 12), E (qty. 12), G (qty. 3), H (qty. 3), J (qty. 6), K (qty. 6), P-551040 Lever assy. (qty. 3). H-800 P-30743 144.90 Enough parts to rebuild 1 gripper bar. Consists of key #’s: C (qty. 8), D (qty. 8), E (qty. 8), F (qty. 1) G (qty. 2), H (qty. 2), J (qty. 1), K (qty. 3), P-551040 Lever assy. (qty. 1).

G&H

124.00 124.00 17.80

GRIPPER CHAIN -601, 602CD/QT (1 only) - RS34, VS34, H234

P-8958 P-8995

69.00 49.90

CHAIN JOINT ASSEMBLY -Carrier link P-5345

7.50

P-30214 P-30215 P-30204 P-30213 P-30306 P-30248 P-30223 P-30206 P-31300 P-31306 P-30250

39.90 46.95 25.95 25.95 49.90 41.95 41.95 46.95 25.95 25.95 32.00

*** Numbers in ( ) indicate number of holes or slots on blade. *** Letters in [ ] indicate Plastic, Rubber, or Steel and Rubber blade material.

P-8937 P-8936 P-8908

CLEAN UP BLADES 500,600,660/62/65 . .12-5/8 x 1-3/4 — (9) [R] 800 SX/DX . . . . . . . .21-3/16 x 1-3/16 — (14) [R] 611, 612 . . . . . . . . . .13-5/16 x 1-3/4 — (9) [R] 660 2nd. head . . . . .12-3/8 x 1-1/2 — (8) [SR] 500 2nd. head . . . . .12-5/8 x 1-9/16 — (9) [SR] 700 1st. head . . . . . .19-1/4 x 1-7/8 — (13) [R] 700 2nd. head . . . . . .18-31/32 x 1-9/16 — (13) [SR] 880 2nd. head . . . . .21-3/16 x 1-19/32 — (14) [SR] RS, VS34 . . . . . . . . .13-7/8 x 1-5/16 — (5) [SR] VS, RS34, H234 . . . .14-1/16 x 1-5/8 — (5) [SR] C248 . . . . . . . . . . . . .20-1/4 x 1-13/16 — (14) [SR]

E&F

CHAINS -500, 600, 800 -700 (delivery-set of 2) -(side jogger 1 only)

DELIVERY STRIPPER FINGER 700 P-772282

6.00

STRIPPER FINGER 800 P-802281

4.50

A STRIPPER FINGER ASSEMBLY For chain delivery Complete P-552280 49.90 (A) Stripper only P-552281 5.50 (B) Block only P-2482423 48.00 (C) Screw P-2407 .60 (D) Washer P-2701 .60

C&D

D A GRIPPER BAR ASSEMBLY Complete 700CD (A) Anvil (B) Shaft (C) Screw (D) Gripper finger (use 7) (E) Set screw (use 3) (F) Collar (G) Gripper spring (on operators side use 1) (H) Gripper spring (on non-operators side use 1)

P-770990 P-771090 P-771060 P-2107 P-661020 P-2506 P-6728 P-551081 P-771080

359.90 259.90 42.00 .60 9.90 .60 4.00 2.40 2.00

** Lever assembly (consists of items (I) - (P) (I) Gripper operating lever (J) Screw (K) Lockwasher (L) Nut (M) Lockwasher (N) Washer (O) Ball bearing (P) Shoulder screw

P-551040 P-551041 P-2107 P-2701 P-2602 P-631 P-2729 P-1803 P-8160

49.90 29.90 .60 .60 .60 .60 .60 6.50 7.90

GRIPPER BAR REPAIR KIT H-700 P-30742 134.90 Enough parts to rebuild 1 gripper bar. Consists of key #’s: C (qty. 1), D (qty. 7), E (qty. 3), F (qty. 3), G (qty. 1), H (qty. 1), K (qty. 3), P-551040 Lever assy. (qty. 1).

B C

B&F D A

PAPER STRIPPER ASSEMBLY - For Hamada C248 Complete (A) Bracket (B) Screw (C) Screw (D) Plate (E) Paper stripper (F) Lockwasher

P-2482280C P-2482423 P-2408 P-2407 P-2482420 P-2482281C P-2701

84.90 48.00 .60 .60 28.00 9.50 .60

••• Eliminate costly downtime with your own emergency kit for your model press. (Master Kit does not include spring kit) REPAIR KITS FOR HAMADA Master kit P-30376 - 513 pcs. 239.80 Junior kit P-31138 - 234 pcs. 179.80 -Pin kit P-30375 - 168 pcs. 99.90 -Ring kit P-30374 - 104 pcs. 55.80 -Nut kit P-30373 - 38 pcs. 21.80 -Washer kit P-30372 - 68 pcs. 49.90 -Screw kit P-30371 - 132 pcs. 77.90 -Spring kit P-31127 - 48 pcs. 69.80

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

Replacement parts for: HEIDELBERG..................................Continued thru page 31. PART #

PART #

PUMP FILTER - Quickmaster 46

SILENCER

SHEET SEPARATOR HOLDER

P-9470

31.20

KOR

HE-KØR113

P-9413

65.00

SHEET SEPARATOR HOLDER - L.H. & R.H. ••• UNIVERSAL. WORKS ON BOTH SIDES OF FEEDER. KORA, KORD, KORS

RIBBED V-BELTS TOK - Drive motor (610mm) TOK - Drive shaft (762mm) GTO 46 - Drive motor (1168mm) GTO 46 - 4 Color Drive Belt GTO 46/52 - Drive motor GTO 52 - Drive motor (1321mm) GTO 52 Z/P, V/P - Drive motor (1016mm) GTO 52 Z/P, V/P - Drive motor (1397mm) Windmill 10 X 15 - Main drive (2150 mm) Windmill 10 X 15 - Main drive Windmill 10 X 15 - Main drive (2362 mm) Windmill 13 X 18 - Main drive

P-3780 P-3783 P-3785 P-3733 P-3716 P-3788 P-3790 P-3791 P-3703 P-3793 P-3893 P-3722

16.50 36.50 57.00 69.00 41.00 98.80 89.90 69.50 352.00 199.80 154.90 229.90

P-3810 P-1697

19.00 7.50

28.90

BRUSH WHEELS For feeder section. K, M, S, SPEEDMASTER (whtie bristle) HE-SR420 K, M, S, SPEEDMASTER for cardboard stock (black bristle) HE-SR500

C E B

21.20 24.00

F D

G K I

TIMING BELTS - TOK STACK-LOAD MASTER FEED MASTER FEED TABLE

HE-KØRD113

34.00

GRIPPER FINGER HE-46212

FEED GRIPPER COMPLETE - GTO 46 & 52 FEED TAPE SPEEDMASTER 72 & 102 MO, SORK A

C D E F G H I J K L

P-3918 P-3927

34.60 19.00

SHEET SEPARATORS

(A) O (B) (C) (D) P (E) (F) Q (G) (H) R (I) (J) S (K) (L) T (M) (N) U (O) (P) V (Q) (R) W (S) (T) (U) (V) (W)

KORD (45°) KORD (45° with pad) KORD (90°) K-Series K-Series w/hood GTO 46 GTO 46 (with hood) GTO 52 GTO 52 (with hood) GTO 52 (45°) M/S Series M/S Series M/S Series SB Series (90°) SB Series (45°) WINDMILL WINDMILL Quickmaster 46/46DI GTO (Operator side) SM52/74 (Operator side) GTO (Non-Operator side) SM52/74 (Non-Operator side) M/S/SM102 Brush

HE-KØ114 7.00 HE-KØ420 10.90 HE-KØ117 7.00 HE-KS117 11.90 HE-KS114 9.90 HE-46117 5.60 HE-46114 6.00 HE-52117 9.90 HE-52118 9.90 HE-52114 3.20 HE-SØ117 24.90 HE-SØ114 29.90 HE-SØ106 33.90 HE-SB117 9.50 HE-SB114 9.50 HE-WI114 10.00 HE-WI117 9.50 HE-46114QM 24.90 HE-52106 53.40 HE-52106SM 64.90 HE-52107 53.40 HE-52107SM 64.90 HE-S0107 29.90

RUBBER HOOD For sheet separators. HE-46114-R

4.90

SHEET SEPARATOR BAR QUICKMASTER 46 & 46DI HE-46117QM

224.90

PLATE SPRING For Quickmaster 4mm 6mm

HE-46099QM-4mm HE-46099QM-6mm

6.40 11.00

SHEET STEADIER BRUSH - GTO 46 / 52, K-Series Complete HE-46403 82.00 Brush only Wing nut Shoulder screw

HE-46420 P-3399 P-8176

6.00 2.00 9.90

COMPLETE (A) Gripper finger (B) Hex head screw (C) Needle bearing (D) Cam roller (E) Flat washer (F) E-ring (G) Stud-for cam roller (H) Taper pin (I) Connecting piece (J) Torsion spring (K) Gripper pad (L) Spring (M) Grooved pin (N) Torsion Spring (not shown) (O) Backing Plate

HE-46511 HE-46212 P-2088 P-3466 P-6838 P-595 P-2759 P-7943 P-431 P-11923 HE-46212-T not sold alone HE-46212-E P-3037 (see note) HE-46212-BP

899.90 12.00 .60 19.90 38.90 .60 .60 23.00 .60 9.90 3.00 ------24.90 .60 ------.90

NOTE: Torsion spring “N” is obsolete. Spring “L” & grooved pin “M” are used in place of it. SPRING For traveling feed gripper. K-series

A B SUCKER FEET

HE-K0144

(A) GTO (9/32 ID x 3/4 OD gum rubber - blue) (A) GTO (9/32 ID x 3/4 OD polyurethane - red) (B) GTO (5/16 ID x 11/16 OD for cardboard) (C) HEIDELBERG/KLUGE (7/8” O.D.) (C) HEIDELBERG (1-1/16” O.D.) (D) HEIDELBERG (5/32” I.D. x 1” O.D.) (D) WINDMILL (5/32” I.D. x 7/8” O.D.) (D) WINDMILL (1/8” .ID. x 29/32 O.D.) (E) SOR (1-1/4” O.D.) (E) MO/SOR (1-3/16” O.D.) (E) MO/SOR (1-1/2” O.D.) (E) Speedmaster 52 (6/16 I.D. x 1-3/16 O.D.) (F) SORKZ For tissue paper (G) TOM/TOK (1-1/4 Long) (G) Quickmaster (11/16 Long)

6.50

F P-5222 P-7568 P-5244 P-5210 P-7556 P-5223 P-7566 P-5234 P-5236 P-5240 P-5243 P-7564 P-5218 P-5215 P-7558

G .90 1.80 1.75 1.60 1.20 .80 .60 .70 .80 .80 1.00 .80 7.00 1.20 .80

SPRING GUIDE (TONGUE) For conveyor K- series HE-KØR420

8.50

RETAINER SPRING For GTO 52 feeder. HE-SØ711

2.40

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

Replacement parts for: HEIDELBERG .................................Continued thru page 31. PART #

PART #

HOLDER ASSEMBLY - GTO 46/52, WINDMILL PLATENS Complete HE-WI434 59.80 Replacement roll pin P-2839 .60 Replacement thumb screw P-2022 3.90 C

SHEET STEADIER ASSEMBLY - GTO 46 / 52, K-Series Complete HE-KØØ27 81.90 (A) Sheet steadier HE-KØR090 38.90 (B) Holder HE-46049 35.90 (C) Thumb screw P-2022 3.90

FRONT GUIDE - For GTO 46/52, K-Series D

(A) Guide only (B) Adjusting knob (C) Retainer spring (D) Adjusting screw

HE-KØ383 P-2932 HE-KØ257 P-2912

SHEET STEADIER BRUSH - S-SERIES D Complete HE-SR467 G F (A) Hex head screw P-2077 (B) Flat washer P-581 P-2603 E (C) Nut (D) Thumb screw P-2924 C (E) Bracket only HE-SR485 B (F) Spring washer P-654 A (G) Sheet steadier brush HE-SR475 B

G J

39.90 24.10 5.50 19.90

159.90 .60 .60 .60 24.90 54.90 .80 69.90

FEEDER BRUSH WHEEL - S-Series, Spdmst. 72/102 Complete HE-SR403 89.90 (A) Spring P-12319 1.40 (B) Thumb screw P-2903 8.90 (C) Small bracket HE-SR498 22.00 (D) Hex head screw P-2043 .60 (E) Large bracket HE-SR473 38.90 (F)Thumb screw P-2924 24.90 (G) Holder HE-SR492 44.90 (H) Pin P-4777 7.00 (I) Brush wheel HE-SR420 21.20 (J) E-Ring P-2753 .60

SHEET SMOOTHERS E

B C A D SHEET SMOOTHER - GTO 46 (Short) Complete (A)Bar only (B)Thumb screw (C)Block only (D)Roll pin

HE-46352 (Not Sold Alone) P-2924 HE-KØR359 P-516

89.80 -------24.90 33.80 .60

Note: ** bars come without holes - you must drill holes to match your existing block. D

C F

SHEET SMOOTHER - GTO 52 Complete (A) Bar only (B) Thumb screw (C) Block only (D) Pan head screw (E) Plate spring (F) Roll pin

HE-52434 HE-52483 P-2924 HE-KØR359 P-2355 HE-46779 P-516

119.90 59.90 24.90 33.80 .80 2.50 .60

Note: ** bars come without holes - you must drill holes to match your existing block. SHEET SMOOTHER PLATE SPRINGS SORZ, SORDZ, SORSZ

HE-SØ588

19.90

SORKZ, SORMZ

HE-SØ924

10.90

E D

KOR (Complete) KORD/KORA (Complete) KORS (Complete) (A) Spring plate (smoother) (B) Screw (C) Bar only (KOR) ** (C) Bar only (KORD/KORA) ** (C) Bar only (KORS) ** (D) Block (E) Thumb screw

HE-KØR434 HE-KØRD434 HE-KØRS434 HE-KØ779 P-2355 HE-KØR483 HE-KØRD483 HE-KØRS483 HE-KØR359 P-2924 B

D&E

134.90 118.90 123.90 3.00 .80 61.90 61.90 79.80 33.80 24.90

F G

C H

F B A SHEET SMOOTHER - S-Series Complete (Operators side) Complete (Drive side) (A) Spring plate (B) Screw (C) Bar only ** (D) Block (E) Thumb screw (F) Spacer piece (oper. side) (F) Spacer piece (drive side)

HE-SØ562 HE-SØ568 HE-SØ779 P-10207 HE-SØ483 HE-SØ359 P-2923 HE-SØ541 HE-SØ573

160.00 160.00 3.20 .60 64.90 38.90 9.90 42.90 42.90

D B

SHEET SMOOTHER - GTO 46 (Long) Complete (A) Bar only (B) Thumb screw (C) Block only (D) Screw (E) Nut (F) Pan head screw (G) Plate spring (H) Roll pin

HE-46434 HE-46483 P-2924 HE-KØR359 P-2305 P-2600 P-2355 HE-46779 P-516

109.80 59.90 24.90 33.80 .60 .60 .80 2.50 .60

A SHEET BRAKE - GTO 46 / 52, K-Series Complete (A) Strap only (B) Block only (C) Thumb screw (D) Stop nut (E) Screw

HE-52467 HE-52500 HE-52473 P-2924 P-2610 P-8174

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

70.00 9.90 29.90 24.90 .60 10.40

Replacement parts for: HEIDELBERG ....................................Continued thru page 31. PART #

PART # INK DISTRIBUTOR ADJUSTING BLOCKS - K-Series Drive side (complete) HE-KØR494K-DS 264.00 (consists of (A) thru (J) & (K) HE-KØR494-DS. 120.00 Operators side (complete) HE-KØR494K-ØS 264.00 (consists of (A) thru (J) & (K) HE-KØR494-ØS. 120.00 BEARING LATCH ASSEMBLY (items (A) thru (F). (A) Screw-Cone point P-2132 3.90 (B) Spring HE-46896 .80 (C) Latch HE-KØR494-L 28.50 (D) Stud P-7164 9.80 (E) Spring washer P-11826 2.90 (F) Taper pin P-431 .60 JOURNAL BOX ASSEMBLY (items (G) thru (J). (G) Journal box HE-KØR494-JB 38.00 (H) Retaining ring P-2771 .60 (I) Needle bearing P-2117 15.90 (J) Adjusting screw P-2913 8.20 (K) Block (drive side) HE-KØR494-DS 120.00 (K) Block (oper. side) HE-KØR494-ØS 120.00 JOURNAL BOX HOUSING ASSY. (items B, G, H, I, &J) HE-KØR494-JBC 104.00

TRANSFER GRIPPER - MOZ, SPEEDMASTER, SORK HE-MT225 38.90

(A) (A) (B)

GTO 46 / 52 Transfer and Imp. drum (urethane tip) Transfer and Imp. drum (plain metal tip) Imp.—Perfecting drum (urethane tip) Reversing Drum (upper position) Reversing Drum (lower position)

HE-52245 HE-52237 HE-MØ237

HE-521020-RU HE-521020-RL

(C)

K-SERIES Transfer and Imp. drum (metalized grit tip)HE-KØR225

(D) (A) (A) (A) (A) (A)

M-SERIES Feed drum (urethane tip) Transfer and Imp. drum (urethane tip) Transfer and Imp. drum (plain metal tip) Transfer drum—Coating unit (metal tip) Imp. drum—Coating unit (urethane tip) Imp. drum—Coating unit (plain metal tip)

(E)

QUICKMASTER 46 / 46DI & TOM / TOK Impression drum (urethane tip) HE-46237QM

(F) (F) (J)

S-SERIES Transfer and Imp. drum (urethane tip) Transfer and imp. drum (plain metal tip) Imp. cylinder gripper-SBD (urethane tip)

49.90 33.00 135.90 79.90 59.90

HE-72225 HE-52245 HE-52237 HE-52237 HE-52245 HE-52237 HE-MO1020 HE-MO1050

CLAW For blanket clamp

30.50

(F) (F) (G) (G)

SPEEDMASTER 72 Transfer and Imp. drum (urethane tip) Transfer and Imp. drum (plain metal tip) Imp.—Perfecting drum (plain metal tip) Transfer drum (large) —Perfecting (plain metal tip)

HE-SK237 HE-SK245 HE-72245S

65.00 39.00 110.90

HE-72245S

110.90

(H) (H) (H) (H) (I)

SPEEDMASTER 102 Feed drum (urethane tip) Feed drum (plain metal tip) Transfer and Imp. drum (urethane tip) Transfer and Imp. drum (plain metal tip) Imp.—Perfecting drum (plain meta l tip)

HE-102237 HE-102245 HE-102237 HE-102245 HE-102225

29.20 36.90 29.20 36.90 53.90

GROOVED GRIPPER PADS - Speedmaster 72 59.90 46.90

P-27744

SHEET STOP For side lays M-Series, S-series, Speedmaster HE-102100

38.90 49.90 33.00 33.00 49.90 33.00 19.90 6.90

65.00 39.00 189.90 87.90

HE-72422-CG HE-72422-PG

TOM, TOK

39.50

HE-SK237 HE-SK245 HE-SBD237 HE-SK1000

Cross groove Parallel groove

SPINDLE For blanket cylinder

HE-46390

THREADED BUSHING For plate cylinder GTO 46 & 52 HE-46329

TRIP BLOCK For plate cam GTO 52 HE-52391

44.90

38.90

8.90

30.00

3.20

ADJUSTING SCREW - For WINDMILL LAY BAR 10 X 15, 13 X 18 (32 mm O.A.L.) (39 mm O.A.L.)

HE-WI135-32 HE-WI135-39

77.90 67.90

CYLINDER BRUSHES KOR, KORA, KORD-62 KORD-64 KORS

P-7659 P-7657 P-7658

401.00 499.90 349.90

HE-MØ252 HE-MØ258 HE-MØ256 P-2009 P-12319

479.90 312.00 312.00 .60 1.40

C GROOVED GRIPPER PADS - Speedmaster 102 Cross groove Parallel groove Diamond groove

HE-102422-CG HE-102422-PG HE-102422-DG

24.90 59.90 22.00

BLANKET BAR ASSEMBLY - M-Series

Forwarding Sucker Assembly Operator Side

HE-S0990-0S

769.90

Non-Operator Side

HE-S0990-DS

769.90

GROOVED GRIPPER PADS (Cross groove) Speedmaster 72 / 102 (after perfector) Drive side HE-72442-D 336.00 Center HE-72442-C 155.00 Operators side HE-72442-Ø 420.00

Complete (A) Upper clamp (B) Lower clamp (C) Screw (7 per assembly) (D) Spring (6 per assembly) (not shown)

HOLDER ASSEMBLY - GTO 46 / 52, K-Series Complete HE-KØ625 Replacement roll pin P-2839 Replacement thumb screw P-2022

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

49.90 .60 3.90

Replacement parts for: HEIDELBERG..................................Continued thru page 31. PART #

PART #

BLANKET BAR ASSEMBLIES Complete Complete Complete Complete Complete Complete Complete Complete Complete Complete Complete Complete

(GTO 46) (GTO 52) (SM 52) (KOR) (KORD) (KORS) (SM 72) (SM 74) (SM 102) (SORDZ) (SORKZ) (SORZ)

HE-46252 HE-52252 HE-52252SM HE-KØR252 HE-KØRD252 HE-KØRS252 HE-72252 HE-74252 HE-102252 HE-SØRDZ252 HE-SØRKZ252 HE-SØRZ252

380.00 323.80 579.90 799.90 810.00 899.90 400.00 639.90 465.00 909.80 650.00 670.00

GTO 46 Complete GTO 52 Complete

HE-46367 HE-52367

591.90 639.80

(A) (A) (A) (B) (C) (C) (D) (E) (E) (F) (G) (H) (I) (I) (J) (K) (K)

HE-46359 HE-52359-L HE-52359-R P-2949 HE-46435 HE-52435 P-7198 HE-46353 HE-52353 P-9138 P-12909 P-2418 HE-46353-M HE-52353-M P-2508 HE-46353-R HE-52353-R

124.90 69.90 69.90 26.90 58.90 64.50 21.90 240.00 240.00 13.00 2.50 .90 40.00 45.00 .60 15.80 15.80

PLATE CLAMP ASSEMBLY - TAIL EDGE - For BACHER PLATE GTO 46 Complete HE-46367-BC (A) Upper clamp - (L.H.) HE-46359-L (B) Upper clamp - (R.H.) HE-46359-R (C) Knurled adjusting nut P-2949 (D) Flat washer P-10942 (E) Eccentric shaft HE-46435 (F) Adjusting stud P-7198 (G) Lower clamp sub assembly HE-46353-BC-S (H) Lower clamp only HE-46353-BC (I) Rubber strip HE-46353-R (J) Metal strip HE-46353-M (K) Threaded stud P-9138 (L) Spring P-12909 (M) Screw P-2418 (I,J) Metal & rubber strip assembly HE-46353-MSR

639.80 69.90 69.90 26.90 1.20 58.90 21.90 240.00 180.00 15.80 40.00 13.00 2.50 .90 79.60

PLATE CLAMP ASSEMBLY - LEAD EDGE - For BACHER PLATE GTO 46 Complete HE-46788-BC (A) Collar P-6725 (B) Collar scale P-6726 (C) Adjustment holder HE-52351 (D) Washer P-2749 (E) Spacer P-6802 (F) Spring P-12148 (G) Threaded stud P-9137 (H) Spring P-12909 (I) Adjusting block HE-52755 (J) Ring scale P-6724 (K) Adjusting stud P-7199 (L) Lower clamp HE-46353-BC (M) Metal strip (not shown) HE-46353-M (N) Eccentric shaft (2 per assm) HE-46435 (O) Upper clamp (1 per assm) HE-46359 (P) Rubber strip (not shown) HE-46353-R (M,P) Metal & rubber strip assembly HE-46353-MSR

839.80 55.80 63.00 29.80 1.00 7.90 3.80 14.90 2.50 29.90 55.80 7.90 180.00 40.00 58.90 124.90 15.80 79.60

PLATE CLAMP ASSEMBLY - LEAD EDGE GTO 52 Complete (A) Clamp (B) Knurled adjusting nut (C) Spacer (D) Spring (E) Eccentric shaft (F) Spring (G) Adjusting stud (H) Lower clamp (I) Screw (J) Set screw (K) Metal strip (L) Rubber strip (not shown) (K,L) Metal & rubber strip assembly

699.90 134.90 26.90 5.80 3.80 64.50 2.50 21.90 240.00 .90 .60 45.00 15.80 79.60

PLATE CLAMP ASSEMBLY - TAIL EDGE

Upper clamp - GTO 46 Upper clamp - GTO 52 (left hand) Upper clamp - GTO 52 (right hand) Knurled adjusting nut Eccentric shaft - GTO 46 Eccentric shaft - GTO 52 Adjusting stud Lower clamp - GTO 46 Lower clamp - GTO 52 Threaded stud Spring Screw Metal strip - GTO 46 Metal strip - GTO 52 Set screw (not shown) Rubber strip - GTO 46 Rubber strip - GTO 52

(I,K) Metal & rubber strip assy. - GTO 46 (I,K) Metal & rubber strip assy. - GTO 52

HE-46353-MSR HE-52353-MSR

79.60 79.60

HE-46788 HE-46359 HE-46435 P-2917 HE-46896 P-2101 P-5519 HE-46755 HE-46353 P-12909 P-2418 HE-46353-M P-2508 HE-46353-R HE-46353-MSR

499.90 124.90 58.90 13.90 .80 .60 .60 32.90 240.00 2.50 .90 40.00 .60 15.80 79.60

PLATE CLAMP ASSEMBLY - LEAD EDGE GTO 46 Complete (A) Upper clamp (B) Eccentric shaft (C) Thumb screw (D) Spring (E) Screw (F) Washer (G) Adjusting bracket (H) Lower clamp (I) Spring (J) Screw (K) Metal strip (L) Set screw (not shown) (M) Rubber strip - GTO 46 (not shown) (K,M) Metal & rubber strip assy. - GTO 46

HE-52788 HE-52359 P-2949 P-6843 P-12148 HE-52435 P-12909 P-7198 HE-52353 P-2418 P-2508 HE-52353-M HE-52353-R HE-52353-MSR

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

Replacement parts for: HEIDELBERG..................................Continued thru page 31. PART #

PART #

PLATE CLAMP ASSEMBLY - LEAD EDGE - For BACHER PLATE GTO 52 Complete (A) Collar (B) Collar scale (C) Adjustment holder (D) Spacer cam (E) Spring (F) Threaded stud (G) Adjusting stud (H) Adjusting block (I) Lower clamp (J) Metal strip (K) Spring (L) Hex head screw (M) Ring scale (N) Nut (O) Eccentric shaft (P) Clamp (Q) Rubber strip (J,Q) Metal & rubber strip assembly

HE-52788-BC P-6725 P-6726 HE-52351 P-6843 P-12148 P-9137 P-7199 HE-52755 HE-52353 HE-52353-M P-12909 P-2089 P-6724 P-2634 HE-52435 HE-52359 HE-52353-R HE-52353-MSR

639.90 55.80 63.00 29.80 5.80 3.80 14.90 7.90 29.90 240.00 45.00 2.50 20.40 55.80 6.50 64.50 134.90 15.80 79.60

• STANDARD CYLINDER JACKETS WINDMILL 10 X 15 .....10 x 14-1/4 ......................... P-30850

E PLATE CLAMP ASSEMBLY - KORD 64 Complete (A) Screw (4 per assm) (B) Upper clamp (C) Flat washer (D) Spring (4 per assm) (E) Lower clamp (F) Screw (2 per assm) (G) Washer (2 per assm) (not shown) (H) Block (I) Nut (3 per assm) (J) Set screw (3 per assm)

HE-KØRD367 P-2008 HE-KØRD359 P-10942 P-12319 HE-KØRD353 P-2105 P-5519 HE-KØR755 P-2604 P-2510 D

1,049.80 .60 300.00 1.20 1.40 569.90 .70 .60 128.90 .60 1.20

• REFINED CYLINDER JACKETS GTO 46 ........................ 15-1/2 x 18 ......................... P-30860 GTO 52 ........................ 16 x 20-3/8 ......................... P-30861 MO ............................... 21-3/4 x 26.......................... P-30862 Speedmaster 72 .......... 21-1/16 x 29-1/4 ................. P-30863 Speedmaster 74 ........... ........................................... P-30872 Speedmaster 102 ........ 27-15/16 x 40-3/4................ P-30864

599.90 998.00 1,699.00 1,455.00 1,867.00 1,998.00

• DIE CUTTING KSBAZ ........................ 21-1/2 x 28-1/2 ................... P-30865 SBB, SBBS, SBBZ ....... 21-1/4 x 32-1/4 ................... P-30866 KSBA .......................... 18-5/8 x 22-1/2 ................... P-30869 S-Series ...................... 22-1/4 x 28-3/8 ................... P-30887 SBG ............................. 24 x 30-1/4 ......................... P-30890

290.00 299.90 193.05 184.00 320.00

INK DISTRIBUTOR RUNNER WINDMILL 10x15 HE-WI466

17.70

Dog & Worm set

HE-46464QM-K

153.90

Worm - Ink / Water Dog - Water

HE-46464QM HE-46428QM

128.90 74.90

INK UNIT OVER-RUNNING CLUTCH ASSEMBLY COMPLETE (K-Series) HE-KØ370 COMPLETE (SM 72/102) HE-72370-CON (A) Retaining ring P-2778 (B) Flat washer P-2715 (C) Ring washer P-2716 (D) Bearing cage P-3452 (E) One-way clutch bearing P-3447 (F) Bearing cage P-3448 (G) Housing Not Sold Alone (H) Sleeve HE-KØ370-S

F 829.90 1.30 4.90 4.90 43.00 279.90 149.90 ----159.90

ADJUSTING GEAR For distributor roller.

75.00 102.50 50.00 74.00 149.90 119.80 129.00 199.90 110.90 151.80 249.90

DOG AND WORM - Quickmaster 46 / 46DI E

KORD 64

WINDMILL 13 X 18....... 12-7/8 x 17-3/4 ................... P-30858 GTO 46 ........................ 15-1/2 x 18 ......................... P-30851 GTO 52 ........................ 16 x 20-3/8 ......................... P-30852 M-Series ....................... 21-1/2 x 26 ......................... P-30853 KORD 62 ..................... 19-1/4 x 24-7/16 ................. P-30854 KORD 64 ..................... 19-1/2 x 25-1/2 ................... P-30855 KOR ............................. 16-3/4 x 22-1/2 ................... P-30859 KORA .......................... 17 x 22-1/2 ......................... P-30857 KORS .......................... 22-1/2 x 28-1/2 ................... P-30856 Speedmaster 52 ........... 15-1/4 x 20-7/8 ................... P-30867

HE-KØRD516

179.90

INK FOUNTAIN END PLATES Sold as a set of 1 Left hand & 1 Right hand. Quickmaster 46 HE-46566QM Quickmaster 46DI HE-46566QMDI GTO 52 HE-52566 GTO 52 CPC/CPT HE-52566CP GTO 46/52 Numbering Unit HE-46566-N Speedmaster 52 HE-52566SM Speedmaster 72 HE-72566 Speedmaster 74 HE-74566 Speedmaster 102 HE-102566 MO HE-MØ566 Spring plate for all (O.S.) HE-72261 Spring plate for all (N.O.S.) HE-72082 Hickey picker for all P-31108

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

79.90 110.00 159.00 218.00 99.90 133.40 165.60 107.00 165.60 120.00 7.00 7.00 .60

Replacement parts for: HEIDELBERG..................................Continued thru page 31. PART #

PART #

HICKEY REMOVERS A

(A) SORS, SORD, SORM, MO P-29981

79.90

(B) Speedmaster 52

79.90

P-29983

P-29982

79.90

(D) Speedmaster 102

P-29980

79.90

RUBBER REPLACEMENT (not shown) for P-29980 only. P-31336

ADJUSTING SCREW ASSEMBLY Complete HE-46427 (A) Screw P-6530 (B) Brass stud P-7174 (C) Nut P-2601 (D) Lockwasher P-11830

LOWER DAMPENING BEARING SUPPORT 4.00

66.00 44.90 31.50 .60 .60

INK BLADE ADJUSTING SCREWS (A) K-Series P-2929 (B) GTO 46/52, M/S Series, Spdmstr 72 P-2928 (C) TOK P-2021

22.90

GTO 46 & 52 D.S. GREEN - Complete GTO 46 & 52 O.S. GREEN - Complete (A) Spring (inside handle “B”) (B) Handle (C) Shoulder screw (D) Dowel pin (E) Trunnion stud (F) Set screw (to hold “G”) (G) Eccentric stud (H) Grooved pin (I) Grooved pin with o-ring (J) O-ring (comes with P-4780) (K) Brass stud (L) Nut (M) Screw (for brass stud)

HE-46415 HE-46400 HE-46896 P-7214 P-8171 P-3132 P-7173 P-2501 P-7163 P-2899 P-4780 P-5330 P-7174 P-2601 P-6530

574.00 574.00 .80 24.90 9.90 6.90 25.90 .60 47.90 4.50 10.50 .60 31.50 .60 44.90

HE-46344 HE-46346 HE-46350 P-7214 P-8171 HE-46896 P-7173 P-2501 P-7163 P-4780 P-5330

349.90 339.90 149.90 24.90 9.90 .80 25.90 .60 47.90 10.50 .60

26.90 5.20

INK ROLLER ASSEMBLY - Windmill 10x x15 (With bearings and runners.) Complete P-31999 148.90 UPPER DAMPENING BEARING SUPPORT WATER BACK UP / FEED COLLAR ASSY - K-Series

COMPLETE (A) Collar - w / “B & D” (B) Bearing (C) Spring (D) Roll pin (E) Cam roller (F) Stud

HE-KØ538 HE-KØ355 P-3460 P-362130 P-10452 P-6838 P-7169

243.80 237.80 6.00 1.80 .60 38.90 21.00

GTO GTO (A) (B) (C) (D) (E) (F) (G) (H) (I)

46 & 52 D.S.Complete 46 & 52 O.S.Complete Support only Handle Shoulder screw Spring (inside handle “B”) Trunnion stud Set screw (to hold “G”) Eccentric stud Dowel pin with o-ring O-ring (comes with P-4780)

INK FOUNTAIN BLADES

BEARING SUPPORTS GTO 46 D.S. - RED / O.S. - YELLOW, GTO 52 D.S. - RED -COMPLETE (w/o latch) HE-46558 GTO 52 O.S. - YELLOW -COMPLETE (with latch) HE-52558 GTO 46 & 52 D.S. - YELLOW / O.S. - RED -COMPLETE (w/o latch) HE-46614 (A) Set screw Not Sold Alone (B) Set screw P-2538 (C) Shoulder screw P-8171 (D) Handle P-7214 (E) Spring (inside handle “D”) Not Sold Alone (F) Trunnion stud P-7173 (G) Set screw (to hold “H”) P-2501 (H) Eccentric stud P-7163 (I) Dowel pin with o-ring P-4780 (J) O-ring (comes with P-4780) P-5330 (K) Spring (underneath “B”) P-152422

340.00 470.00 339.90 --------1.40 9.90 24.90 --------25.90 .60 47.90 10.50 .60 3.90

WINDMILL 10x15 .............. (37.6 cm x 10.1 cm) .... HE-WI095-15 WINDMILL 13x18 .............. (48.0 cm x 10.1 cm) .... HE-WI095-18 GTO 46 ............................. (45.3 cm x 8.4 cm) ...... HE-46095 GTO 46 (Numbering Unit) ... ................................... HE-46095-N GTO 52 ............................. (51.3 cm x 9.4 cm) ...... HE-52095 GTO 52 (Segmented) ......... ................................... HE-52095-S GTO 52 (Numbering Unit) ... ................................... HE-52095-N KOR .................................. (58 cm x 10.1 cm) ....... HE-KØR095 KORD 64 .......................... (67.1 cm x 10.1 cm) .... HE-KØRD095 KORS ................................ (74.2 cm x 10.1 cm) .... HE-KØRS095 M Series ............................ (66.2 cm x 12.9 cm) .... HE-MØØ95 SORDZ .............................. (90.1 cm x 11.7 cm) .... HE-SØRDZ095 SORM ............................... (73.0 cm x 11.7 cm) .... HE-SØRM095 SORMZ ............................. (73.1 cm x 17.5 cm) .... HE-SØRMZ095 SORZ ................................ (83.1 cm x 11.8 cm) .... HE-SØRZ095 SORKZ ............................. (66.0 cm x 11.8 cm) .... HE-SØRKZ095 SORSZ ............................. (103.1 cm x 17.5 cm) .. HE-SØRSZ095 TOK, TOM (27.6 cm x 7.1 cm) ...... HE-T0095 QUICKMASTER 46 ........... (33.6 cm x 7.1 cm) ...... HE-46079QM

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

299.90 447.90 450.00 899.90 399.90 1290.00 899.90 369.90 350.00 328.50 479.90 600.00 979.90 750.00 599.90 593.00 974.90 280.00 240.00

Replacement parts for: HEIDELBERG.................................Continued thru page 31. PART #

PART #

DAMPENING ROLLER ADJUSTMENT BLOCK Complete (A) Gear shaft (B) Spring (C) Bracket (D) Knurled nut (E) E-ring (F) Decal washer (G) Decal washer (H) Nut

HE-KØR416 HE-KØR304 HE-KØR328 HE-KØR418 P-2946 P-2754 P-7464 P-7465 P-2603

140.00 73.90 2.00 89.80 9.50 .60 4.90 4.90 .60

WATER TROUGH END SUPPORT KOR

HE-KØR10102

13.70

PLASTIC WATER FOUNTAIN ROLLER BEARING KOR

HE-KØR10104

OVER RUNNING CLUTCH ASSEMBLY - GTO 46 & 52 Complete (INK) Complete (WATER)

HE-52226 HE-52370

362.90 440.00

(A) (B) (C) (D) (E) (F)

HE-52226-S P-3458 (Not Sold Alone) P-4792 P-2720 P-10752

82.90 109.90 ----1.80 .60 1.10

Sleeve One way clutch bearing Housing only Pin Washer Retaining ring

2.20

WATER FOUNTAIN HOSE CLAMP K-Series

HE-KØR347

38.90

TEFLON SEALS SETS For Quickmaster 46 (set includes 1 ea. left / right hand)

Spring for M-Series Delivery Gripper Operator Side Non-Operator Side

HE-M01081 HE-M01080

6.70 2.40

(A) (B)

95mm From end to end 102 mm From end to end

P-31161 P-31181

48.80 49.80

TEFLON SEAL PACKS (A) Pack of 5 sets (A) Pack of 10 sets

P-31161-5 P-31161-10

236.00 462.00

(B) (B)

P-31181-5 P-31181-10

236.00 462.00

Pack of 5 sets Pack of 10 sets

TEFLON SEALS - GTO 46 / 52 - For use on Varn units. 1 Pack only (2 pcs.) P-30712 19.90 Set of 5 packs P-31168 97.50 Set of 10 packs P-31169 188.90 TEFLON SEALS - TOK / TOM - For use on Heidelberg dampening units 1 Pack only (2 pcs.) P-30713 18.90 Set of 5 packs P-30833 89.50 Set of 10 packs P-30834 174.90

WATER FOUNTAIN TRAYS (A) TOM, TOK (B) GTO 46 Old style (ser # 650058-654211) (C) GTO 46 New style (ser # 656798-698328)

HE-TØ316 HE-46316-ØS HE-46316-NS

262.00 184.00 184.00

**1 pack consists of: (1) Right hand seal and (1) Left hand seal.

BUFFER SPRING - Windmill 10x15, 13x18 For roller carriage

HE-WI444

32.90 DAMPENING FELTS

WATER CLUTCH ASSEMBLY - GTO 46 & 52 HE-46418

QUICKMASTER QUICKMASTER DI

P-11739 P-11740

ANGLE - Paper stripper. GTO 46 & 52

HE-462301

4.70 9.50

90.00

229.90

HOLD DOWN STRAPS For HE-462301 shown at top left column, this page. GTO 46 / 52

HE-462281

26.90

OVER RUNNING CLUTCH LEVER ASSEMBLY - GTO 46 & 52 Complete - Ink unit (A) Lever & knob assembly (B) Collar - without pins (C) Bearing race (D) One way clutch bearing (E) Collar - with pins (F) Washer - bearing retainer (G) Belleville washer

HE-46259 P-320416 P-6785 HE-46261 P-3454 P-6784 P-2720 P-11833

599.90 32.00 64.80 51.80 389.90 64.80 .60 6.90

SPRING CLIP For HE-462281 shown above. GTO 46 / 52

HE-462321

GRIPPER FINGER - GTO 46/52, K-Series w/o Urethane HE-521050 with Urethane HE-521020

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

.90

1.50 9.90

Replacement parts for: HEIDELBERG.................................Continued thru page 31. PART #

PART #

GRIPPER BAR ASSEMBLIES - GTO 46/52, K-Series Complete Complete Complete Complete Complete

(GTO 46) (GTO 52) (KOR, KORA, KORD 62) (KORD 64) (KORS)

(A) Anvil (GTO 46) Anvil (GTO 52) Anvil (KOR, KORA, KORD 62) Anvil (KORD 64) Anvil (KORS) (B) Shaft (GTO 46) Shaft (GTO 52) Shaft (KOR, KORA, KORD 62) Shaft (KORD 64) Shaft (KORS) (C) *Holder assembly (D) **Holder (E) **Finger with urethane (F) **Backing plate (G) **Holding screw (H) **Belleville washer (I) **Shoulder screw (J) *Arm assembly (GTO 46 & 52) *Arm assembly (KOR, KORA, KORD62) *Arm assembly (KORS, KORD 64) (K) **Arm only (GTO 46 & 52) **Arm only (KOR, KORA, KORD62) **Arm only (KORS, KORD 64) (L) **Cam roller stud (GTO 46&52) **Cam roller stud (K series) (M) **Cam roller (GTO 46 & 52) **Cam roller (K series) (N) **Pin (GTO 46 & 52) **Pin (K series) (O) Collar (P) Spring (GTO 46 & 52) (Q) Spring (GTO 52) (R) Pin (R) Screw (K series)

HE-460990 HE-520990 HE-KØR0990 HE-KØRD0990 HE-KØRS0990

949.90 999.90 1,200.00 1,330.00 1,750.00

HE-461090 HE-521090 HE-KØR1090 HE-KØRD1090 HE-KØRS1090 HE-461060 HE-521060 HE-KØR1060 HE-KØRD1060 HE-KØRS1060 HE-521000 HE-521061 HE-521020 HE-521062 P-2003 P-651 P-8161 HE-521040 HE-KØR1040 HE-KØRD1040 HE-521041 HE-KØR1041 HE-KØRD1041 P-7159 P-7169 P-11179 P-6840 P-373 P-1894 P-6739 HE-521080 HE-521085 P-2834 P-2101

459.90 483.90 560.00 554.90 664.90 65.80 63.90 108.90 109.80 109.80 47.00 26.90 9.90 3.00 .60 1.00 5.50 189.90 120.00 107.80 119.00 76.90 76.90 16.90 21.00 38.90 32.90 .60 .60 12.00 4.90 4.50 .60 .60

*indicates a sub-assembly. **indicates components of a sub-assembly. Note: Item (B) Shaft must be taper reamed for pins in field. GRIPPER PADS - SPEEDMASTER 72 & 102 A

(A) For ultraviolet & infrared dryers HE-721061-U

14.90

(B) For standard

24.90

HE-721061

GRIPPER PAD RAIL For S-Series gripper bars. HE-SK1061

19.90

WATER OSCILLATING HOUSING ASSEMBLY K-Series Operators side Drive side (shown) A

HE-KØ429 HE-KØ431

HE-T00990 HE-T01090 P-2506 P-6728 HE-T01060 HE-T01020 P-2112 P-11904 HE-T01085 P-6734 P-2512 HE-T01080 P-2810 P-2610 HE-T01041 P-580 P-11113 P-2103 P-3239

699.90 520.00 .60 4.00 49.90 14.90 .60 3.50 3.50 19.90 .60 2.30 .60 .60 32.50 .60 8.00 .60 3.00

GRIPPER BAR ASSEMBLY - QUICKMASTER 46 & 46DI COMPLETE (46) COMPLETE (46DI) (A) Anvil (comes with P-11904 (Angled Pad) (A) Anvil (comes with P-5631 (Flat Pad) (B) Set screw (C) Adjusting collar (D) Gripper spring (E) Delivery gripper for 46 (E) Delivery gripper for 46DI (F) Screw (G) Gripper shaft (H) Taper pin

HE-460990QM HE-460990QMDI HE-461090QM HE-461090QMDI P-2506 P-6858 HE-461080QM HE-461020QM HE-461020QMDI P-2112 HE-461060QM P-2810

519.90 549.90 339.80 369.90 .60 38.90 9.90 23.90 23.90 .60 68.90 .60

GRIPPER LEVER ASSEMBLY HE-461040QM (Consists of I thru M - also included with complete assembly)

49.90

• • • •

.60 .60 8.00 37.90

(I) Screw (J) Washer (K) Ball bearing (L) Gripper lever only

(M) Stop nut (N) Rubber pad (Flat) (N) Rubber pad (Angled)

P-2103 P-5569 P-11113 HE-461041QM P-2610 P-11904 P-5631

.60 3.50 5.00

349.80 429.90

GEAR FOR METERING ROLL - QM46 (A) Overall Length: 13.5 mm HE-46555QM

GRIPPER BAR ASSEMBLY - TOK Complete (A) Anvil (B) Set screw (C) Collar (D) Shaft (E) Gripper finger (F) Cap screw (G) Gripper pad (H) Gripper spring (I) Tension collar (J) Set screw (K) Gripper spring (L) Taper pin (M) Stop nut (N) Gripper operating lever (O) Washer (P) Ball bearing (Q) Screw (R) Bushing

(B) Overall Length: 22 mm HE-46555QM-UG

10.00

72.70

GRIPPER BAR ASSEMBLY - WINDMILL Complete 10 X 15 Complete 13 X 18

HE-WI0990-15 HE-WI0990-18

SCREW - For gripper bar operating arm

HE-T1307

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

540.00 599.90 5.90

Replacement parts for: HEIDELBERG.................................Continued thru page 31. PART #

PART # GRIPPER CHAINS

TOK (set) GTO 46 / 52 (set) KOR (set) KORD (set) KORS (set) MO (set) SPEEDMASTER 72/102 SORD QUICKMASTER 46 (set) QUICKMASTER 46DI (set)

J U

GRIPPER BAR ASSEMBLY COMPLETE (Speedmaster 72) ........................... HE-720990 COMPLETE (Speedmaster 102) ......................... HE-1020990-U (A) Chain link - 4 ea. ......................................... P-8715 (B-1) Carrier link assembly - operators side ........ HE-720991 (B-1) Carrier link assembly - operators side ........ HE-1020991 (B-2) Carrier link assembly - non-oper. side ........ HE-720992 (B-2) Carrier link assembly - non-oper. side ........ HE-1020992 - Link only - for (B-1) ................................... HE-720991-L - Link only - for (B-1) ................................... HE-1020991-L - Link only - for (B-2) ................................... HE-720992-L - Link only - for (B-2) ................................... HE-1020992-L - Inner chain link - 2 for each assembly ....... P-8715 - Needle bearing ......................................... P-3461 - Dowel pin for P-8715 - 2 for each assy...... P-2898 - Grease fitting ............................................ P-3672 (C) Washer ....................................................... P-2738 (D) Screw.......................................................... P-2103 (E) Clamping piece ........................................... HE-721066 (F) Finger ......................................................... HE-721020 (G) Gripper supporting shaft.............................. HE-721060 (G) Gripper supporting shaft.............................. HE-1021060 (H) Center pivot bearing.................................... HE-721092 ( I ) Gripper operating lever ............................... HE-721040 (J) Taper pin - 3 per complete assembly ........... P-2865 (K) Cam roller ................................................... P-6871 (L) Set screw .................................................... P-10017 (M) Spring guide................................................ P-2970 (N) Pin .............................................................. P-4768 (O) E-Ring......................................................... P-2759 (P) Clamp ......................................................... HE-721067 (Q) Clamping piece ........................................... HE-721065 - Screw ....................................................... P-2103 - Nut............................................................ P-2603 - Lockwasher .............................................. P-10836 (R) Screw.......................................................... P-2143 (S) Gripper pad ................................................. HE-721061-U (T) Clamp (also in S-Series) ............................. HE-721064 (U) Shaft ........................................................... HE-721090 (U) Shaft ........................................................... HE-1021090

115.00 219.00 2,200.00 2,200.00 1,199.00 691.90 207.00 219.90 249.90

GRIPPER BAR ASSEMBLY CARRIER LINKS SPEEDMASTER 72 & 102 A

3,999.00 3,999.00 39.90 320.00 289.70 320.00 289.70 196.00 212.80 196.00 212.80 39.90 11.00 2.80 1.30 11.40 .60 34.00 139.90 329.90 489.90 124.00 189.90 1.40 66.20 .60 37.90 19.80 .60 40.00 31.00 .60 .60 .60 .60 14.90 34.00 399.90 450.00

HE-T01100 HE-521100 HE-KØR1100 HE-KØRD1100 HE-KØRS1100 HE-M01100 HE-721100 HE-SØRD1100 HE-461100QM HE-461100DI

D B

Complete (oper. side) Complete (non-oper. side)

HE-720991 HE-720992

320.00 320.00

(A) Link only (oper. side) (A) Link only (non-oper. side) (B) Inner chain link (C) Needle bearing (D) Dowel pin (E) Grease fitting

HE-720991-L HE-720992-L P-8715 P-3461 P-2898 P-3672

196.00 196.00 39.90 11.00 2.80 1.30

Stripper Finger SHEET STOPS 1) KORD 62 ........................................................ HE-KØRD2281-62 (for ser. #335790 & below, otherwise use HE-KØRD2282-64.)

34.00

2) KORD 62 & 64 ................................................ HE-KØRD2282-62 (for ser. #335791 & above, otherwise use HE-KØRD2282-62.)

34.00

3) KORD 64 ........................................................ HE-KØRD2281-64

34.90

4) KORD 64 ........................................................ HE-KØRD2282-64 for ser. #335791 and above, otherwise use HE-KØRD2282-62.)

34.00

5) KORA, KORD-64, KORS (front - side)............. HE-KØRD2284

49.90

6) KORA, KORD-62 (front - center) ..................... HE-KØRD2283-62

42.00

7) KORD-64, KORS (front - center) ..................... HE-KØRD2283-64

49.90

STRIPPER FINGER ............................................ HE-KS15112

2.90

STAR ROD BRUSH ASSY. Complete Brush only Collar only Rubber O-ring CARRIER LINKS - K/M/GTO Series (A) M-Series - wide attachment (B) M-Series - short attachment (C) K-Series - operators side (C) K-Series - non-operators side (D) Star rod carrier link (K/S) (E) GTO 46/52

A GRIPPER CHAIN CONNECTING LINKS (A) KOR, KORD, KORS / M-Series (B) KOR, KORD, KORS (offset link) (C) Connecting plate

P-8739 P-8740 P-8732 P-8742 P-8734 HE-521100-A

B P-8761 P-8762 P-8712-P

44.90 44.90 44.90 44.90 44.90

C 9.50 13.90 8.50

P-30842 P-30842-B P-30842-C P-553

12.90 8.50 4.50 .60

HE-523170 HE-KØRD3170-62 HE-KØRD3170-64 HE-MØ3170 HE-SD3170 HE-SR3170 HE-SK3170 HE-SM3170 HE-SS3170

21.90 77.90 94.00 64.90 82.90 87.90 87.90 87.90 92.50

STAR ROD ASSEMBLIES GTO 52 KOR, KORA, KORD 62 KORD 64 M (series) SORDZ SORZ SORKZ SORMZ / SPEEDMASTER 72 SORSZ / SPEEDMASTER 102

NOTE: THESE DO NOT COME WITH BRUSHES OR WHEELS

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

Replacement parts for: HEIDELBERG.................................Continued thru page 31. PART #

PART # CARBON BRUSHES Carbon Brush Carbon Brush S-Series Speedmaster Speedmaster 102Z Speedmaster 102 Speedmaster 102V 102D+L 102V (Main motor) TOK/TOM (Motor)

P-9431 P-9432 P-9769 P-9433 P-9434 P-9435 P-9436 P-9437 P-9440

69.80 4.00 38.90 69.90 69.90 39.90 29.90 24.90 20.00

ROLLER SNAP SWITCH - All S-Series Located on operators side outer delivery frame P-9805

42.90

POWDER TUBE ASSEMBLY Complete (short tube)......................................... HE-KØR6030 Complete (long tube) .......................................... HE-KØR6040

524.90 524.90

Powder tube sub assy. (A - I) ............................ HE-KØR6046 (A) Manifold ...................................................... HE-KØR6050 (B) Screw.......................................................... P-2044 (C) Washer ...................................................... P-592 (D) Gasket ........................................................ P-6422 (E) Rubber washer............................................ P-11036 (F) Lock nut ...................................................... P-2616 (G) Powder tube guide ...................................... HE-KØR6051 (H) Stop screw .................................................. P-2351 (I) Screw.......................................................... P-2082

419.80 119.90 .50 .60 1.00 5.00 1.10 49.90 .60 .60

Spray nozzle sub assy. (J - M) .......................... HE-KØR6047 (J) Nozzle......................................................... HE-KØR6056 (K) Screw.......................................................... P-2921 (L) Spring ......................................................... P-15601 (M) Nozzle tube ................................................. HE-KØR6055

147.80 42.00 6.90 3.90 119.90

Powder tube sub assy. - short (N - R) ............... HE-KØR6035

99.90

Powder tube sub assy. - long (N - R) ................ HE-KØR6045 (N) Short tube (for HE-KØR6030) ..................... HE-KØR6052 (N) Long tube (for HE-KØR6040) ..................... HE-KØR6053 (O) Nut .............................................................. P-2681 (P) Compression nut with gasket ...................... P-2941 (Q) Guide collar................................................. HE-KØR6054 (R) Set screw .................................................... P-2499

120.00 65.80 68.00 .60 27.90 65.80 .60

LIMIT SWITCHES (A) GTO 46/52, M/S Series, Speedmaster 72/102

P-9836

124.90

(B) GTO 46/52, M/S Series, Speedmaster 72/102

P-9837

99.80

P-9838 P-9839

119.90 69.75

(D) GTO 46 / 52 - Located behind blower tubes

P-4074

49.90

VARIABLE SPEED PULLEY For K-Series P-4291

HE-WI046

HE-521327 HE-521328 P-11778 P-2580

1,598.00

COMPRESSION SPRING - WINDMILL 10 x 15 For variable speed control.

GUIDE WHEEL KIT - GTO 52 Complete Wheel only O-Ring Set screw

25.80 15.00 2.10 .60

85.70

BOWDEN CABLE WINDMILL

HE-WI3101

119.90

DELIVERY TABLE CABLE K-Series SB-Series 8 Watt FLOURESCENT BULB - GTO 46 / 52, TOM / TOK

P-9743

9.00

14 Watt FLOURESCENT BULB - KORD 64

P-9726

22.00

HE-KØ971 HE-S1539

55.00 43.90

Lay Gauge Pin Kit Set of 5

P-31133

BRASS FILTER SCREENS Windmill Platens (24mm collar) GTO 46 & 52 (28 mm collar) GTO 46/52, Windmill (38 mm collar)

P-9410 P-9411 P-9412

25.90 25.90 29.90

SLIP RING BRUSHES K-Series (shown) S-Series S-Series Paired Collector Brush

PUMP VANE

P-9428 P-9438 P-9439 P-9429

10.90 10.70 5.60 61.90

P-9444

59.90

Starwheel (A) Star/Pointed Surface (for K/S/M series)

P-30842-0

(B) Knurled/Dimpled Surface (GT0 46/52)

P-30842-GT0

(B) Knurled/Dimpled Surface (for K/S/M series)

P-30842-K

P-30842-S

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

Replacement parts for: HEIDELBERG.................................Continued from page 21. PART #

PART # CAM FOLLOWERS

PNEUMATIC SPRING For Speedmaster 102 Safety guard (11-7/8” end to end) Delivery (16-5/8” end to end)

P-29990 P-29991

101.20 136.30

BLOW DOWN FAN For Speedmaster 102 delivery Terminal connection Wire connection

P-4204 P-4205

225.90 225.90

EMERGENCY KITS

TOK/TOM P-31143 Consists of: 6 Impression gripper fingers / 1 Wash-up blade / 12 Sucker feet / 1 Set of teflon seals.

239.80

QUICKMASTER 46 P-31144 Consists of: 8 Impression gripper fingers / 1 Wash-up blade / 12 Sucker feet / 1 Dampening felt / 1 Tape track

289.80

QUICKMASTER DI46 P-31145 Consists of: 8 Impression gripper fingers / 1 Wash-up blade / 12 Sucker feet / 1 Dampening felt

279.80

GTO 46 (A) Transfer & imp. cylinder / gripper shaft. ....... P-3441 (B) Side lay shaft. ............................................. P-4368

109.90 39.00

GTO 52 (A) Transfer & impression cylinder & storage drum / gripper shaft.............................................. P-3441

109.90

K-SERIES (C) Imp. cyl.shaft / sucker bar mechanism Outer lever. ........... P-6870

109.90

M-SERIES (D) Transfer & impression cylinder & storage drum / gripper shaft.............................................. P-3416 (E) Reversing drum........................................... P-3443 (F) Register feed drum / gripper shaft. .............. P-3444

197.90 163.00 110.00

SORZ / SORDZ / SORKZ / SORMZ / SORSZ (G) Register feed drum / gripper shaft ..(cam facing cylinder O.S. & D.S.) .............. P-3442 (H) Register feed drum / gripper shaft ..(cam facing side frames O.S & D.S.) ......... P-3445 (F) Imp. cyl. & storage drum / gripper shaft. ...... P-3444

155.00 110.00

SPEEDMASTER 72 / 102 (G) Register feed drum/ gripper shaft ..(cam facing cylinder O.S. & D.S.) .............. P-3442 (H) Register feed drum / gripper shaft ..(cam facing side frames O.S. & D.S.) ........ P-3445 (F) Transfer & imp. cylinder / gripper shaft. ....... P-3444 (H) Transfer gripper........................................... P-3445

155.00 110.00 155.00

SPEEDMASTER 74 (I) Delivery table. ............................................. P-3439

69.90

SPEEDMASTER 102 (J) Gripper opening lever on del. gripper bars. . P-6871 (G) On lever (OEM #71-010-110) / inking unit. .. P-3442

66.20 119.00

QUICKMASTER (A) Impression cylinder / gripper shaft. ............. P-3441

109.90

119.00

HARDWARE EMERGENCY KITS

GTO 46 INK ROLLER KIT Consists of: (6) Blue Distributor / Ductor (1) Red Form (1) White Form (1) Yellow Form

HAS YOUR PRESS EVER BEEN DOWN DUE TO A SIMPLE PIN OR SPRING? YOU CAN ELIMINATE COSTLY DOWN TIME IN MINUTES WITH YOUR OWN EMERGENCY KIT DESIGNED TO CONVENIENTLY FIT IN YOUR DESK DRAWER. EACH KIT COMES IN IT’S OWN MULTI-COMPARTMENT RECLOSABLE BOX FOR QUICK, EASY SELECTION AND STORAGE. PART NUMBERS FOR THE INDIVIDUAL ITEMS ARE ALSO INCLUDED INSIDE. MASTER KIT NUT KIT WASHER KIT SCREW KIT RING KIT PIN KIT

All kits below 43 pcs. 60 pcs. 168 pcs. 47 pcs. 100 pcs.

P-30397 P-30392 P-30396 P-30393 P-30395 P-30394

219.90 21.50 40.00 96.00 28.90 37.50

KORD 62 INK ROLLER KIT Consists of: (2) Blue Form / Distributor (3) Red Form / Distributor / Ductor (2) White Form / Distributor / Ductor (2) Brown Form / Distributor / Ductor

QUICKAMSTER 46 (1ST. UNIT) INK ROLLER KIT Consists of: (1) Yellow 1st. Ink Form (1) Blue 2nd. Ink Form (1) Black 3rd. Ink Form (1) Black Ink Transfer Roll #1 (1) Black Ink Transfer Roll #2 (1) Black Ink Transfer Roll #3 (1) Black Ductor

P-30457 P-46H10B P-46H10R P-46H10W P-46H10Y

741.85 86.25 89.65 86.25 87.50

P-31656

1,597.05

P-30916 P-30918 P-30917 P-30919

203.90 181.90 181.90 181.90

P-31735

755.25

P-34H10 P-34H11 P-34H13 P-34H20 P-34H21 P-34H22 P-34H30

128.00 106.00 222.00 86.00 86.00 81.00 86.00

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

Replacement parts for: CHIEF 15, 115, 215, 17, 117, 217, 20, 22, 25/25 PROF, PART # VARIABLE SPEED PULLEY 15, 17 P-1629 (Gestetner) G-63E 115, 215, 117, 217 P-1627 (Gestetner) G-17E

V-BELTS 15, 17 (Motor to pump) 37” 15, 17 (Clutch to motor) 44” 15 (Clutch to drive shaft) 36” 17 (Clutch to drive shaft) 38”

P-4906 (Gestetner) G-6C

PART # LIFTING GEAR STUD For feeder ratchet 15, 115, 215, 117, 217 4” wide w/wide shoulder P-4519 4” wide w/thin shoulder P-4542

179.90 169.90

9.90

BLOWER TUBE BRACKET

12.50

P-4905

9.90

P-4907 (Gestetner) G-27E

9.00

UPPER PULLOUT FEED ROLLER P-15125 (Gestetner) G-17H

34.90

DOUBLE SHEET EJECTION ROLLER P-15273 (Gestetner) G-19H

10.90

RUBBER SUCTION FOOT - X-series & Super Chief 2000 P-5225 120.00 P-5204 2.00

SUCKER FOOT (CUP)

C A&B

P-5201 (Gestetner) G-229G

FLAT SUCKER FOOT

P-1552

SUCKER TUBE HOLDER ASSEMBLY New style 15, 17 P-15259 (Gestetner) G-16G (A) Holder P-15166 (B) Retainer clip P-15227 (C) Screw P-137 (D) Set screw P-864

8.00

.80

44.00 29.90 8.00 .60 .60

SHEET SEPARATOR (A) 15, 17 P-15114 (B) X-Series & Super Chief P-52114

.90 .90

SHEET SEPARATOR ASSEMBLY Complete P-50112 (A) Screw P-293 (B) Washer P-573 (C) Sheet separator P-52114 (D) Block P-50113 (E) Plate P-50121 (F) Screw (not shown) P-215 (G) Thumb screw P-1019

64.00 .60 .60 .90 36.90 16.00 .60 1.80

TIMING BELTS For feeder on X-Series & Super Chief 2000. Also for Davidson 500, 700 3/4” wide X 22-1/2” long P-1662 3/8” wide X 15” long P-4965

22.90 12.00

ELEVATOR HANDLE ASSEMBLY Table raise X-Series & Super Chief 2000 P-50955

PAPER RETAINER Center

P-15433 (Gestetner) G-11S

26.90

CONVEYOR TAPE All models Cloth P-3900 44.00 Note: Tension can be adjusted by weights under conveyor.

JOGGER SIDE GUIDE FEATHER SPRING Non-operators side R.H. P-15477 (Gestetner) G-16T Operators side L.H. P-15471 (Gestetner) G-11T

COUNTER (no lever) 15 17 COUNTER ARM

P-36954 (Gestetner) G-20K P-27954

4.30 4.30

58.00 129.00

P-15956 (Gestetner) G-19K

22.40

P-15383

89.90

ADJUSTING ARM For paper stop P-15853

53.00

PAPER STOP ARM ASSEMBLY P-15399

134.90

PAPER STOP By impression cylinder

160.00

KNOB STUD For chain delivery & feed table handwheel P-4521 16.80

FEEDER GUIDE Operators side & non-operators side P-15048

P-15168 72.00 (Gestetner) G-119G,G-128G

••• Designed to fit both left and right hand sides.

P-4912

SUCKER FOOT

35.50 28.00

FEELER FINGER 21.50

P-15141 4.80 (Gestetner) G-55R (Gestetner) G-OW142

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

126, Super Chief 2000, X-Series • GESTETNER 115/117G, 211, 213, 311, 312, 313 PART #

PART # PLATE CYLINDER GEAR 15, 17, (14-1/2° PA)

PAPER DEFLECTOR 15,17,115,117,215,217

P-15241 (Gestetner) G-52R P-255241 P-44

PAPER DEFLECTOR X-Series, Super Chief SCREW

GRIPPER LEVER ASSEMBLY P-15207 (Gestetner) G-3M & G-E14AØ59

39.90 49.90 .60

P-15313 (Gestetner) G-3P 115, 117, 215, 217 (20° PA) P-115313

289.90

BLANKET CYLINDER GEAR 15, 17 (14-1/2° PA) P-15214 (Gestetner) G-3N 115, 117, 215, 217 (20° PA) P-115214

199.80

115, 117, 215, 217 (20° PA) P-115191

199.80

SPRING ASSEMBLY Impression cylinder arm 15, 17 X-Series & Super Chief 2000 Complete P-15205 Clip P-6088 Spring P-15213

6.90

CLAMP LOCK For plate cylinder P-115807

P-15746

87.90

TENSION GUIDE ARM SCREW For plate cylinder P-11468

13.50

P-15583 P-115583

P-255854

TAIL CLAMP ASSEMBLY - X-Series & Super Chief 2000 Complete P-255367 (A) Clamp bracket P-255729 (B) Spring P-255724 (C) Retaining ring (not shown) P-669 (D) Shaft (not shown) P-255793 (E) Pin bar clamp P-255341 (F) Screw P-836 (G) Pin bar (8 point) P-255323 (H) Pin bar (10 point) P-255739 (I) Thumb nut P-11549 (J) Thumb screw P-11498

380.00 46.00 1.50 .60 34.90 179.90 .60 49.90 49.90 9.90 13.50

CLUTCH PULLEY REPAIR KIT 15, 17, 115, 117, 215, 217 Complete P-15564 145.80 Pulley cover P-15617 94.00 (Gestetner) G-35E Shaft P-15614 24.90 (Gestetner) G-33E Weights (set of 4 only) P-12593 59.90 (Gestetner) G-37E V-Belt - 44” P-4912 12.50 V-Belt - 37” P-4906 9.90 (Gestetner) G-6C Spring P-15591 4.30 (Gestetner) G-36E Bearing (need 2) P-774 6.90 (Gestetner) G-3U Key P-550 .60 (Gestetner) G-ØWØ62

WATER CAM ASSEMBLY Complete Cam

DRIVE & PUMP TOGGLE SWITCH 15, 17 O.S. & N.S. P-15305

31.80

DRIVE & PUMP ROCKER SWITCH P-15826

55.90

Water pawl Pawl spring Ink pawl

P-15262 (Gestetner) P-15363 (Gestetner) P-15268 (Gestetner) P-15267 (Gestetner) P-15355 (Gestetner)

WATER STOP 15, 17, 115, 117, 215, 217 RELAY

139.90

74.90 149.90

INTERMEDIATE DRIVE GEAR 15,17 (14-1/2° PA) P-15865 72.90 (Gestetner) G-64R P-15457 69.90 (Gestetner) G-E14H115,G-58L 115,117,215,217 (20° PA) P-115854 69.90 DRIVE GEAR For X-Series

24.00 2.90 7.50

10.80 DRIVE SHAFT 15, 17 115, 117, 215, 217

214.90

119.80

GRIPPER FINGER SUPPORT ASSEMBLY P-15187

RETAINING BAR (20 point) Master cylinder 15N.S. & 17 O.S./N.S.

220.00

P-4833

79.90

117.80 G-170UA 85.80 G-9U, G-170U 28.90 G-163U 3.90 G-LØØ4058 28.90 G-66V

P-30379 X-Series & Super Chief 2000 1st. & 2nd. head (Uses 16) P-5096

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

35.90 9.90

Replacement parts for: CHIEF 15, 115, 215, 17, 117, 217, 20, 22, 25/25 PROF, PART # FRICTION BEARING For water fountain roller 15, 17 P-5525 (Gestetner) G-157U

PART #

9.00

WORM GEAR ASSEMBLY Inker unit P-15446 (Gestetner) G-192V

99.90

INK IDLER GEAR

P-15455

69.90

P-15464 (Gestetner) G-134V

66.90

P-15463 (Gestetner) G-138V

48.90

OSCILLATING WORM Ink & water DOG Ink WATER DUCTOR ASSEMBLY - 15, 115, 215, 17, 117, 217 Complete P-15424 184.90 (Gestetner) G-443 (A) Shaft P-15540 34.90 (Gestetner) G-161U-S (B) Stud P-4500 21.50 (C) Cam roller P-1450 6.50 (D) Arm P-15607 24.90 (Gestetner) G-21U2 (E) Yoke shaft P-15340 24.90 (Gestetner) G-2Ø42 (F) Latch P-15551 4.30 (Gestetner) G-60U, G-91V (G) L.H. Spring P-15336 4.10 (Gestetner) G-62U, G-93V (H) Center pivot P-15322 29.90 (Gestetner) G-161UP ( I ) Lever arm P-15344 67.00 (Gestetner) G-83VA (J) R.H. Spring P-15331 4.10 (Gestetner) G-61U, G-ØU56

WASH UP BLADE Black rubber 15 O.S. (11” X 11/16”) Tan 15, 17, (11-3/8” X 1-1/2”) 215, 217 (11 X 2-1/8”) XL, Super Chief 1st. head (13-3/4” X 1-1/8”) XL, Super Chief 2nd. head (13-3/4” X 2-1/16”)

C-2167H-32 C-2171D-524 P-30309 P-30238 P-30217

WATER FOUNTAIN SHAFT & RATCHET 15, 17 P-15402 115, 117, 215, 217 P-115402 (A) Shaft 15, 17 P-15371 A (A) Shaft 115, 117 215, 217 P-115371 (B) Ratchet P-15370 (C) Pin P-381

SHAFT For water form roller 15, 17, 115, 117, 215, 217

P-15378 (Gestetner) G-15ØU

WATER DUCTOR LEVER SPRING P-15549

12.50 16.00 25.95 25.95 25.95

IMPROVED

••• DESIGNED WITH REPLACEABLE END CAPS. INK FOUNTAIN ASSEMBLY 15, 115, 215 - (Gestetner) G-E31H477 P-15071 Fountain only - (Gestetner) G-70V P-15072

INK FOUNTAIN ASSEMBLY With deeper ink well for 50% more ink capacity. 17, 117, 217 P-17766 439.80 Fountain only - (Gestetner) G-3V-3 P-17789 179.90 THUMB SCREW

P-1660 (Gestetner) G-5R2 215, 217 (second water head) P-1654

13.50

P-15079 49.90 (Gestetner) G-73V 17, 117, 217 Bigger blade for deeper ink well. P-17233 56.40 (Gestetner) G-11V2 Note: * Due to the variations of ink fountains it may be necessary to file the side of the blade stamped “O” for a perfect fit.

79.90 97.90 29.90 39.90 59.00 .60

49.90

INK DUCTOR ASSEMBLY Complete (A) Cam roller (B) Stud

5.50

40.00

(E) Latch (F) R.H. Spring (G) L.H. Spring

TIMING BELT 17, 117 (water)

P-11474

INK FOUNTAIN BLADE 15, 115, 215

(D) Arm CAM ROLLER Water oscillator arm P-5831 (Gestetner) G-129U

389.90 174.00

13.90 10.50

(H) Shaft ( I ) Center pivot (J) Lever arm

P-15690 P-1431 (Gestetner) P-8096 (Gestetner) P-15550 (Gestetner) P-15572 (Gestetner) P-15551 (Gestetner) P-15331 (Gestetner) P-15336 (Gestetner) P-15332 P-15322 (Gestetner) P-15334 (Gestetner)

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

G-85V G-86V G-89V

208.00 6.50 9.40 21.80

24.90 G-F14V012 4.30 G-60U 4.10 G-61U 4.10 G-62U 41.90 29.90 G-161UP 49.90 G-83VA

126, Super Chief 2000, X-Series • GESTETNER 115/117G, 211, 213, 311, 312, 313 PART #

CONNECTING LINK BAR For chain delivery 15, 17, 115, 117, 215, 217

PART #

P-151596 34.00 (Gestetner) G-120CP

ARM EXTENSION ASSEMBLY For chain pile delivery 15, 17, 115, 117, 215, 217 P-151597 42.90

GRIPPER BAR ASSEMBLY ••• Anvil is made of reinforced cast zinc which prevents bowing and lasts longer. Complete

DELIVERY ROLL GRIPPER

(A) Anvil P-15644 4.90 (Gestetner) G-OW138 (Gestetner) G-33Q

BACK STOP STRIPPER For chain delivery P-152280

6.00

(B) Retaining ring ** Gripper shaft assembly (C) - (E) (C) Stop block (D) Roll pin (E) Shaft (F) Cap screw (G) Gripper holder (H) Screw (I) Hold down clip

GRIPPER SUPPORT

P-15586

10.20

(J) Gripper finger ** Gripper operating lever assembly (K) - (P) (K) Gripper operating lever (L) Cap screw (M) Hex nut (N) Lock washer (O) Cam roller

GRIPPER CHAINS (set of 2) 15, 17, 115, 117, (Super Chief 2000 & X-Series 1st. head) P-8945 72.00 (Gestetner) G-548C3 G-E1ØA323 215, 217, (X-Series & Super Chief 2nd. head) P-8949 120.00 22 P-8969 83.00

(P) Shoulder screw (Q) Collar (comes with set screw) (R) Set screw (S) Spring

P-150990 180.00 (Gestetner) G-125CP P-151090 116.00 (Gestetner) G-126CP P-670 .60 P-151010 48.00 P-151063 19.90 P-376 .60 P-151060 32.00 P-40 .60 P-151061 19.90 P-187 .60 (Gestetner) G-HS158 P-151062 1.20 (Gestetner) G-HW307 P-151020 1.70 (Gestetner) G-HW306 P-151040 49.00 P-151041 32.00 (Gestetner) G-E10A173 P-39 .60 (Gestetner) G-CS42U P-479 .60 (Gestetner) G-L0HT051 P-627 .60 P-1424 7.80 (Gestetner) G-L0HW309 P-8037 (Gestetner) G-L0HS159 P-98137 10.00 P-2 .60 P-151080 1.80 (Gestetner) G-L0HU124

GRIPPER BAR REPAIR KIT - Super Chief 2000 & X-Series Consists of (B - D, F - P, Q, & S) P-30736 CONNECTING LINK

P-8700

223.90

5.00

PICK UP CAM ASSEMBLY To open gripper bars P-151240 56.00 (Gestetner) G-511C3

REPAIR KITS HAS YOUR PRESS EVER BEEN DOWN DUE TO A SIMPLE PIN OR SPRING? YOU CAN ELIMINATE COSTLY DOWN TIME IN MINUTES WITH YOUR OWN EMERGENCY KIT DESIGNED TO CONVENIENTLY FIT IN YOUR DESK DRAWER. EACH KIT COMES IN IT’S OWN MULTI-COMPARTMENT RECLOSABLE BOX FOR QUICK, EASY SELECTION AND STORAGE. PART NUMBERS FOR THE INDIVIDUAL ITEMS ARE ALSO INCLUDED INSIDE.

SPROCKET & SHAFT ASSEMBLY Chain delivery 15, 17, 115, 117, 215, 217 P-151160 292.50 (Gestetner) G-113CP G-E1ØA157, G-E1ØA287

MASTER KIT JUNIOR KIT NUT KIT WASHER KIT SCREW KIT RING KIT PIN KIT SPRING KIT

P-1765 - 880 pcs. P-31136 - 432 pcs. P-1763 - 60 pcs. P-1764 - 68 pcs. P-1760 - 376 Pcs. P-1761 - 100 pcs. P-1762 - 180 pcs. P-30326 - 96 pcs.

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

459.80 199.80 31.90 31.90 159.90 39.80 99.80 299.80

Replacement parts for: DAVIDSON 221, 233, 241, 400, 500, 500P, 501 502P, 560, 600, PART #

FILTER SPRING

P-12034

PART #

P-4869 P-15305

180.00 31.80

UPPER PULLOUT ROLL

P-51125

60.00

DETECTOR Sheet feed

D-88-2057-01

19.90

SUCTION FOOT

D-88-2827-01

17.90

RUBBER SUCTION FOOT ASSEMBLY For heavy stock Complete D-88-2200-18 1) Holder P-50168 1) Sucker foot P-5204 1) Screw P-50067

46.90 32.40 2.00 9.90

FEEDER GEARS, PAWLS & SPRINGS Drive gear P-50452 Ratchet D-88-1442-01 Feed & stop pawl P-52786 Feed pawl spring P-52718 Stop pawl spring P-52787

179.80 238.80 72.50 4.50 5.50

ELEVATOR HANDLE ASSEMBLY Stacker P-502630

119.90

ELEVATOR HANDLE SHAFT P-50962

12.00

(A) GUIDE Back stop (B) GUIDE L.H. Operators side (C) GUIDE R.H. Non-operators side

D-88-1333-01 D-88-1331-02 D-88-1331-03

59.90 34.90 34.90

STOP FINGER SHAFT ASSEMBLY Complete 500 Complete 700 Shaft with fingers only 500 Shaft with fingers only 700 Timing pulley for both Pin

D-88-5996-03 D-88-5996-04 D-88-6954-01 D-88-6954-02 D-88-1372-01 P-441

539.80 539.80 499.90 499.90 29.90 .60

STRAP ASSEMBLY (7” long strap) Complete D-88-4562-01 (A) Block D-88-2167-01 (B) Knob P-312 (C) Screw P-35 (D) Washer P-561 (E) Strap D-88-4418-01 Strap (feeder) P-50420

39.90 14.50 4.50 .60 .60 8.50 19.00

STRAP ASSEMBLY (8-5/8” long strap) Complete D-88-2170-01 (A) Block D-88-2167-01 (B) Knob P-312 (C) Screw P-35 (D) Washer P-561 (E) Strap D-88-2166-01

32.90 14.50 4.50 .60 .60 15.00

C D B A

P-1662 P-1656

160.00

4.90

TOGGLE SWITCHES Main drive Pump & Drive 500P, 700P

TIMING BELTS Large (feeder) Small (conveyor)

ELEVATOR HANDLE ASSEMBLY Feeder P-50955

22.90 13.90

KNOB ASSY. Beater bar 500, 600, 700, 500P, 700P 3-5/8” P-50541 49.90 KNOB ASSY. Beater bar 501, 601, 701, 502P, 702P 4-1/2” P-51819 47.50

UPPER FEED ROLL BEARING

D-88-1719-02 or C-310-007567D P-767

SHEET SEPARATOR or Cat whisker Brass P-50114

99.80 5.00

MARBLE MARBLE MARBLE MARBLE MARBLE

RETAINER 500 (12-1/2” long) RETAINER 700 (19-1/2” long) RETAINER 901 (21-1/2” long) - 1” Glass - 1” Steel

D-88-1760-01 D-88-1760-03 D-88-1760-04 P-761 P-759

49.90 49.90 49.90 1.30 4.90

1.00

B C

STOP PAWL SPRING

P-52660

FEEDER RELEASE PAWL P-52786

13.00

72.50

A CHANNEL ASSEMBLY (A) Rod (B) Nylon ball (C) Clip (D) Screw (E) Guide

D-88-2076-01 D-88-2186-01 P-752 D-88-3959-01 P-140 D-88-2077-01

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

259.80 24.90 3.00 9.80 .60 219.80

601, 660, 700, 700P, 701, 702P, 760, 901, Dual-a-matic, Mark-I, Roll Converter PART # COUNTER ASSEMBLY 500, 600, 700 702P 221, 233 Counter arm

D-88-1653-01 P-4799 D-221-0190 D-88-1620-01

SPRINGS For jogger assembly Operators side L.H. D-88-2188-01 Non-operators side R.H. D-88-2188-02

PART #

119.80 182.90 119.80 21.00

14.50 14.50

BLANKET CYLINDER GEAR Gear with keys D-88-1608-01 Gear only D-88-1610-01 Keys D-251-0088 Screws P-1892

BLANKET DRUM GEAR COUPLING 500, 600, 700 D-88-1615-01 502P, 702P D-88-1615-02 221, 251, 233 Top plate cylinder coupling D-251-0105 500P, 700P D-88-4377-01

299.80 254.00 24.00 3.20

96.00 119.90 104.90 259.90

PLATE SEGMENT CLAMP STRAP ASSEMBLY

D-88-3173-01

16.50 Screw

CONVEYOR TAPE 500, 501, 502P, 600, 700, 701, 702P P-4990 CONVEYOR TAPE 221, 241 P-3914

41.90

CONVEYOR TAPE Roll Converter

32.50

P-3913

SPROCKET ASSEMBLY For conveyor P-8612

DACRON GEAR For blanket drum gear drive D-88-1396-03

UNIVERSAL DRIVE SHAFT 500 (for ball bearing or bushing) D-88-1391-01 or D-88-3634-01 700 (for ball bearing or bushing) D-88-1391-03 or D-88-3634-02

90.00

D-88-1635-01

15.80

DACRON, NYLON & ALUMINUM GEARS 500, 600, 700 Off large cylinder gear NYLON D-88-1499-01 or D-88-3083-02 ALUMINUM D-88-1499-X1 501, 601, 701 Off large cylinder gear DACRON C-306-009847D

69.90 69.90 69.90

500, 600, 700 Off ink unit NYLON ALUMINUM 501, 601, 701, Off ink unit DACRON

D-88-1552-01 D-88-1552-X1

89.90 99.90

D-88-6720-01

69.90

GEAR For ink vibrator roll 501, 601, 701

C-120-004904D

107.40

CHROME DRAW SHEETS 500 - 13” (no bend) 500 - 14” (with bend) 600 - 11” (no bend) 700 - 13” (no bend) 700 - 14” (with bend) 901 - 14” (with bend)

D-88-2321-01 D-88-2321-02 D-88-2321-09 D-88-2321-05 P-30788 C-199-006704D

59.90 59.90 115.90 69.90 79.90 90.00

PACKING SHEETS 500, 501(.005) - 13” (.008) - 13” (.010) - 13” (.005) - 14” (.008) - 14” (.010) - 14” 700, 701(.005) - 13” (.008) - 13” (.010) - 13” (.005) - 14” (.008) - 14” (.010) - 14” 901(.005) - 14” (.010) - 14”

D-221-0415 D-221-0416 D-221-0417 D-227-0006 D-227-0007 D-227-0008 D-233-0048 D-233-0049 D-233-0050 D-233-0189 D-233-0190 D-233-0191 C-199-006635D C-199-006634D

4.90 4.90 4.90 4.90 4.90 4.90 4.90 4.90 4.90 4.90 4.90 4.90 4.90 4.90

69.90

199.90 199.90

••• The nylon gear is double wide & designed to preserve the life of your other gears. Just turn it around and reuse it. Twice the life span as original design and your machine will run up to 50% quieter.

13.50 .60

STUD For blanket drum latch 26.90

MAIN DRIVE GEAR For drive shaft (N)ylon or (S)teel 500, 600, 700 Dualith D-88-3808-01-N 69.90 D-88-3808-01-S 99.90 500P, 700P D-88-4552-01-N 69.90 D-88-4552-01-S 69.90 501,601,701,502P,702P D-88-6728-01-N 79.90 D-88-6728-01-S 79.90

BLANKET HUB ASSEMBLY Reinforced lip for durability & longer life. D-88-3928-01

D-88-2597-01 or D-88-2597-02 P-57

179.90

PIN BAR For plate & impression segment 500, 600, 700 C-125-007223D

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

159.80

Replacement parts for: DAVIDSON 221, 233, 241, 400, 500, 500P, 501 502P, 560, 600, PART #

PART # RUBBER STOP For Roll Converter paper stop assy. D-33-0504-01

EXTENSION BAR For impression segment 700, 601, 701, 700P

DUCTOR ROLLER CLIP Ink & water

D-88-2822-03

99.90

D-88-0804-01

7.80

DUCTOR SPRING LATCH For roller bracket Ink & water D-88-2606-01

7.90

JOGGER PLATE ASSEMBLIES 500, 600, 700 (Non-operators side) (Operators side) (Rear) 501, 601, 701

WASH UP BLADES For Baldwin wash up units 500, 501 (11-3/4 x 2-1/4, 4 Holes, Steel & rubber) D-88-5200-02 700, 701 (18-3/4 x 2-1/4, 5 Holes, Steel & rubber) D-88-5200-01 901 (20-3/4 x 2-1/4, 6 Holes, Steel & rubber) D-88-5200-03 NOTE: WASH UP UNITS ALSO AVAILABLE

B&C

D A

D-88-1574-01 D-88-1574-03 D-88-1574-04

76.50 89.90 88.00

FROG ASSEMBLY For dampening system 501, 601, 701 Complete D-88-6656-01 (A) Wiper D-88-6607-01 (B) Screw P-1871 (C) Lock washer P-644 (D) Frog D-88-6606-01 (E) Thumb screw P-312

63.80 9.90 .60 .60 49.90 4.50

STRIPPER PLATE For chain delivery section 600, 601, 700, 701, 702P

D-88-1863-02

59.90

CONTROL HANDLE ASSEMBLY (A) 500P, 700P (not shown) (B) 501, 502P, 701, 702P (C) 500, 700 (D) 501, 601, 701

49.90

D-88-5363-01 D-88-5363-03 D-88-1451-01 D-88-5363-02

D-88-1469-07 D-88-1469-09 D-88-1469-08 D-88-1468-05 D-88-1468-06 D-88-1462-01 D-88-6724-01 P-50

99.90

559.80 579.80 579.80 499.90 519.80 79.90 130.00 .60

69.80 104.00 79.80 93.80

CONNECTING LINK ASSEMBLY (L.H. & R.H.) 500, 600, 700 D-88-4148-01 501, 601, 701, 702P P-8744

79.90 99.90

OLD STYLE CONNECTING LINK Only (A) D-88-2817-01

10.50

GRIPPER BAR LINK Only 500, 600, 700 (B) Operators side L.H. D-88-2533-01 (B) Non-operators side R.H. D-88-2818-01

38.00 38.00

GRIPPER BAR LINK Only 901 (B) Operators side L.H. C-399-006720D (B) Non-operators side R.H. C-399-006719D D-88-2649-02

72.00 72.00

GRIPPER BAR CARR. LINK Only 501, 601, 701, 502P, 702P (B) Operators side L.H. P-8722 64.90 (B) Non-operators side R.H. P-8721 64.90

NEW STYLE CONNECTING LINK Only (A) P-8749

F GEARED DAMPENING ROLLER 500 Complete 501 Complete 700 Complete Roller and shaft only 500, 501 Roller and shaft only 700 Gear 500, 700 Gear 501 Screw for all

PAWL ASSEMBLY For pile jogger assy.

B SMALL PNEUMATIC CYLINDER For jogger blower manifold D-88-1857-01

91.20 91.20

(Rear)

D-88-1916-02 D-88-1915-02 D-88-1913-04 or D-88-1893-01 D-88-1893-03

49.90 49.90 69.90

INK FOUNTAIN BLADE 500, 501, 502P 600, 601, 700, 701, 702P 901

4.00

G C&D H A B

87.00 87.00 9.00

JOGGER SPRING & BLOCK ASSEMBLY - Conveyor Complete D-88-2178-02 79.80 (A) Block only D-88-1968-01 29.90 (B) Thumb screw P-312 4.50 (C) Screw P-194 .60 (D) Lockwasher P-623 .60 (E) Spring - Left hand D-88-2188-02 14.50 (F) Spring stop D-88-2187-02 5.50 (G) Clip D-88-2286-01 8.90 (H) Spring - Right hand D-88-2188-01 14.50

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

601, 660, 700, 700P, 701, 702P, 760, 901, Dual-a-matic, Mark-I, Roll Converter PART #

PART #

F H A E

REPAIR KITS FOR ALL DAVIDSONS ••• ELIMINATE COSTLY DOWN TIME WITH YOUR OWN EMERGENCY

GRIPPER BAR ASSEMBLY

KIT FOR YOUR MODEL PRESS.

Master kit Nut kit Washer kit Screw kit Ring kit Pin kit Spring kit

P-1771 - 1053 pcs. P-1769 - 87 pcs. P-1770 - 79 pcs. P-1766 - 447 pcs. P-1767 - 105 pcs. P-1768 - 234 pcs. P-30327 - 101 pcs.

GRIPPER CHAINS (set of 2 only) 221, 251, 500, 700 501, 601, 701, 502P, 702P, 901

P-8929 P-8935

439.80 44.80 44.80 225.80 39.80 119.80 239.90

74.90 92.90

••• MADE OF REINFORCED STEEL TO PREVENT BOWING. ••• UNIVERSAL - MAY BE USED FOR STANDARD OR SLITTER. 500

Complete (slitter not avail.) (A) Anvil (standard) (B) Shaft (C) Finger (D) Spring (E) Cam roller (F) C-Ring (G) Spiral pin (H) C-Ring ( I ) Cam roller (J) Retaining ring

D-88-2832-14 D-88-6945-01 D-88-6385-02 D-88-2518-01 C-199-006219D P-1445 P-668 P-345 P-682 P-1407 P-700

719.80 469.90 149.90 13.00 6.90 7.20 .60 .60 .60 9.00 .60

501, 502P

Complete (slitter not avail) (A) Anvil (standard) (B) Shaft (C) Finger (D) Spring (E) Cam roller (F) C-Ring (G) Spiral pin (H) C-Ring ( I ) Cam roller (J) Retaining ring

D-88-2832-15 D-88-6945-02 D-88-6385-02 D-88-2518-01 C-199-006219D P-1445 P-668 P-345 P-682 P-1407 P-700

719.80 459.90 149.90 13.00 6.90 7.20 .60 .60 .60 9.00 .60

Universal - fits standard or slitter Complete p-700990 (A) Anvil (slitter) D-88-8037-01 (B) Shaft D-88-6385-04 (C) Finger D-88-2518-01 (D) Spring C-199-006219D (E) Cam roller P-1445 (F) C-Ring P-668 (G) Spiral pin P-345 (H) C-Ring P-682 ( I ) Cam roller P-1407 (J) Retaining ring P-700

799.80 559.90 149.90 13.00 6.90 7.20 .60 .60 .60 9.00 .60

600, 700P 701, 702P

Universal - fits standard or slitter Complete D-88-2832-12 (A) Anvil (slitter) D-88-8037-02 (B) Shaft D-88-6385-04 (C) Finger D-88-2518-01 (D) Spring C-199-006219D (E) Cam roller P-1445 (F) C-Ring P-668 (G) Spiral pin P-345 (H) C-Ring P-682 ( I ) Cam roller P-1407 (J) Retaining ring P-700

799.80 559.90 149.90 13.00 6.90 7.20 .60 .60 .60 9.00 .60

901

Complete (slitter not avail.) (A) Anvil (standard) (B) Shaft (C) Finger (D) Spring (E) Cam roller (F) C-Ring (G) Spiral pin (H) C-Ring (I) Cam roller (J) Retaining ring

999.80 799.90 180.00 12.80 6.90 7.20 .60 .60 .60 9.00 .60

F H

J C

700

SAVE MONEY BY REPLACING ONLY THE PARTS THAT WEAR INSTEAD OF REPLACING THE WHOLE GRIPPER BAR ASSEMBLY. GRIPPER BAR REPAIR KIT - 500, 501, 502 Consists of: (C) Gripper finger-qty. 4, (D) Spring-qty. 4, (E) Cam-qty. 1, (F) Ret. ring-qty. 1, (G) Spiral pin-qty. 8, (H) Ret. ring-qty. 1, (I) Cam roller-qty. 1, (J) Ret. ring-qty 1.

P-30739

89.90

GRIPPER BAR REPAIR KIT - 700, 701, 702 Consists of: (C) Gripper finger-qty. 8, (D) Spring-qty. 8, (E) Cam-qty. 1, (F) Ret. ring-qty. 1, (G) Spiral pin-qty. 8, (H) Ret. ring-qty. 1, (I) Cam roller-qty. 1, (J) Ret. ring-qty 1.

P-30740

139.90

GRIPPER BAR REPAIR KIT - 901 Consists of: (C) Gripper finger-qty. 8, (D) Spring-qty. 8, (E) Cam-qty. 1, (F) Ret. ring-qty. 1, (G) Spiral pin-qty. 8, (H) Ret. ring-qty. 1, (I) Cam roller-qty. 1, (J) Ret. ring-qty 1.

P-30744

162.90

NOTE: REFERENCE ALL KEY NUMBERS ON THESE THREE REPAIR KITS TO GRIPPER BAR ASSEMBLIES IN THE NEXT COLUMN.

C-399-006713D C-125-006722D C-311-006714D C-117-006727D C-139-006747D P-1445 P-668 P-3045 P-667 P-1407 P-700

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

Replacement parts for: BAUM FOLDER, MBM, MARTIN YALE, PROFOLD, VARN KOMPAC PART #

PART # TOP PERFORMANCE KIT For MBM Fastfold 17 MI-1 Consists of: 3) MI-AA1462 Auto feed wheels 2) MI-AA1121 Rubber wheels 1) MI-AA1077 Abrasive stone with flap

TIRES (In order of O.D. x I.D. x Width) Caliper tire (1-11/16” x 15/16” x 1/2”) Roller tire (1” x 15/32” x 1”) Roller tire (1-13/16” x 1-3/32” x 1”) Tire sucker wheel (1-3/4” x 1-7/16” x 1/4”)

B-3750 B-45290 B-48429 B-50080

7.90 4.75 6.35 7.60

PERFORATING WHEEL 6 Tooth 15 Tooth 18 Tooth (shown) 24 Tooth 31 Tooth 41 Tooth 64 Tooth

B-7618 B-7895 B-7896 B-7619 B-6798 B-7791 B-11962

12.90 16.55 16.55 10.95 12.55 8.75 12.50

STACKER BELT

B-6346

301.00

P-3905

21.90

FEED REPAIR TAPES (Set of 4)

132.70 20.55 23.55 24.35

TOP PERFORMANCE KIT For Martin Yale MY-1 87.90 Consists of: 1) MY-W-0008015 Feed roll for M-Y Friction folder 1) MY-M-0003548 Feed rubber for 12 x 17 folder 1) MY-M-0095138 Drive friction 1) P-11215 Bushing 2) MY-M-0003080 Accessory rubber for MY Friction folder TOP PERFORMANCE KIT For Profold 1117FM, 1117BM, 1118FM PF-1 62.90 Consists of: 1) PF-109696 Feed wheel tire 10.15 2) B-3750 Pull out tires (each) 7.90 2) PF-109777 Slides (each) 15.60 1) PF-109624 Stationary roller 9.90 TEFLON SEALS FOR VARN KOMPAC Old style (set of 2) P-30083 New style (set of 2) P-30093 Old style (5 pack) P-30724 New style (5 pack) P-30714 Old style (10 pack) P-30725 New style (10 pack) P-30715 FELT CLEANING SEALS Set of 6 (2 seals per set) P-11743 Set of 12 (2 seals per set) P-11744

9.80 9.80 46.00 46.00 90.00 90.00 9.50 17.00

For SOLNA / EAGLE / CHIEF25/25-1 Profiteer P-30002 89.90 BACKING PLATE KIT Has both Left Hand and Right Hand assembly. V-92380 38.55 STRIPPER

B-6438

SHEET DETECTOR TAB - Amber colored For vacuum feed B-50498

13.25

GEAR & CLUTCH ASSEMBLY For Varn 1250 Multilith V-12404-1/4 360, 375, 9800 V-36404-5/16 360 V-36404-7/16 1360, 1650 V-13404-17/32

58.90 58.90 58.90 58.90

4.90 SYRINGE - 2.5 OZ.

FEED ROLLER - For 52 / 58 AB DICK FOLDER Tan tire P-31067 Black tire P-31068 TIRE KIT For Baum Folder 714 B-48429-K Consists of: 1) B-45290 Tire (each) 2) B-48429 Tire (each)

23.90 10.50

DRILL BLOCKS For Challenge 1-1/2” Diameter P-30811 3” Diameter P-30812

3.30 3.50

4.75 6.35

29.90 7.90

COLLARS For Baum Folder (A) 7/8 I.D. x 1-1/2 O.D. x 5/8 THK. B-6411 (B) 7/8 I.D. x 1-3/4 O.D. x 5/8 THK. B-7780

2.00

17.45

TIRE KIT For Baum Folder 417, 200, 400, 600, Mark I, Mark II, Junior Jet, Autoset B-6402-K 19.90 Consists of: 8) B-6402 Tire (each) 2.65 TIRE KIT For Baum Folder B-3750-K Consists of: 4) B-3750 Caliper tire (each)

P-30088

27.90 17.10

DUROWEAVE “VELOUR DAMPENING COVERS” • THEY LAST FOR MONTHS The special yarn that is used gives Duroweave covers the ability to shrink to a snug fit on your roller. The weave is a continuous wrap—no seams to come loose. • THEY’RE EASY TO CLEAN Duroweave covers can be cleaned off in your shop sink under warm water. No need for expensive attachments or equipment. • THEY’RE LINT AND PATTERN FREE The surface loops of the knit are evenly sheared to provide a uniform pile height across the roller length and are guaranteed to be 100% lint free—no contaminating fibers. The covers have a seamless knit for pattern free printing. AVAILABLE FOR ALL MODELS.

THIS IS JUST A SAMPLE OF OUR TOTAL INVENTORY

ALL ROLLER KITS ON $ALE AB DICK

HAMADA

360 NEW STYLE SOFT RUBBER INK ROLLER KIT P-5004 Consists of 5 rollers 1) P-36010 Upper form (measure diameter) 1) P-36011 Lower for (measure diameter) 2) P-36021 Distnbutor (measure diameter) 1) P-36030 Ductor 375, 9800 SOFT RUBBER INK ROLLER KIT P-5021 Consists of 5 rollers 1) P-37010 Upper for (measure diameter) 1) P-37011 Lower form (measure diameter) 2) P-37021 Distributor (measure diameter) 1) P-37030 Ductor

216.15

240.25

MULTILITH 1250W, LW, 2650W OLD STYLE SOFT RUBBER INK ROLLER KIT P-5046 205.95 Consists of 6 rollers 1) P-12130 Ductor (measure rubber to rubber 3) P-12121 Distributor (measure diameter, rubber to rubber & shaft to shaft) 2) P-12110 Form (measure rubber to rubber) 1250W, LW, N, 2850W NEW STYLE SOFT RUBBER INK ROLLER KIT P-5037 180.70 Consists of 5 rollers 1) P-12230 Ductor 2) P-12221 Distributor (measure diameter, rubber to rubber & shaft to shaft) 2) P-12210 Form (measure rubber to rubber)

CHIEF 15, 115, 215, 1st. head / Itek 1115 SOFT RUBBER INK ROLLER KIT P-30452 300.15 Consists of 6 rollers 2) P-15011 Form 2) P-15021 Top & bottom idler 1) P-15020 Back idler 1) P-15031 Ductor (measure shaft to shaft) 17 SOFT RUBBER INK ROLLER KIT P-30450 Consists of 6 rollers 2) P-17011 Form 2) P-17021 Top & bottom idler 1) P-17020 Back idler 1) P-17030 Ductor

321.50

DAVIDSON 400, 500, 501, 500P, 501P, 502P NEW STYLE P-30408 237.30 Consists of 5 rollers 1) P-50110 Upper ink form (measure overall shaft length) 1) P-50111 Lower ink form (measure overall shaft length) 2) P-22020 Ink distributor & ductor 1) P-22022 Front ink distributor (with offset bearings) P-30415 Consists of 5 rollers 1) P-70110 Upper form (measure shaft to shaft) 1) P-70111 Lower form (measure shaft to shaft) 2) P-23020 Distributor & Ductor 1) P-23022 Front distributor

318.10

600 & 600CD SOFT RUBBER INK ROLLER KIT P-30426 Consists of 5 rollers 1) P-10610 Small upper form 1) P-10611 Large lower form 2) P-10620 Distributor (measure diameter) (bushings not included) 1) P-10630 Ductor (bushing not included)

700, 700CD (O.S. & N.S.) SOFT RUBBER INK ROLLER KIT P-30432 387.05 Consists of 6 rollers 1) P-10110 Small upper form 1) P-10111 Large upper form 2) P-10120 Distributor (measure diameter & overall shaft length) bushings not included. 1) P-10130 Ductor (bushings not included) 1) P-10121 Distributor (measure diameter & shaft to shaft) bushings not included.

RYOBI / ITEK Ryobi 2800 / Itek 960 SOFT RUBBER INK ROLLER KIT P-30445 Consists of 5 rollers 1) P-28010 Small upper form 1) P-28011 Large lower form 2) P-28020 Distributor (measure diameter) 1) P-28030 Ductor (measure shaft to shaft) Ryobi 3200 / Itek 960 SOFT RUBBER INK ROLLER KIT P-30446 Consists of 5 rollers 1) P-32R11 Small upper form 1) P-32R12 Large lower form 2) P-32R20 Ink distributor (measure rubber to rubber) 1) P-32R33 Ductor (N.S.) (measure shaft to shaft)

253.70

271.75

HEIDELBERG GTO 46 SOFT INK RUBBER ROLLER KIT P-30457 Consists of 9 rollers 1) P-46H10Y Form 1) P-46H10B Ductor 1) P-46H10W Form 1) P-46H10R Form 4) P-46H10B Distrubutor 1) P-46H10B Ductor GTO 46 SOFT RUBBER WATER ROLLER KIT P-30458 Consists of 3 rollers 2) P-46H10G Form 1) P-46H10G Ductor GTO 52 SOFT RUBBER INK ROLLER KIT P-30459 Consists of 9 rollers 1) P-52H10Y Form 1) P-52H10B Form 1) P-52H10W Form 1) P-52H10R Form 4) P-52H10B Distributor 1) P-52H10B Ductor GTO 52 SOFT RUBBER WATER ROLLER KIT P-30460 Consists of 3 rollers 2) P-52H10G Form 1) P-52H10G Ductor

NOTE: Please measure diameter and rubber to rubber on distributors before ordering.

258.40

741.85

249.40

810.55

278.75

Part #

Model #

Ply

Edges

Size

A.B. DICK P-30054 P-30055 P-30057 P-30059 P-31256 P-31418

. . . . . .

360 . . . 360 . . . 9800 . . 385 . . . 9880 . . QP254 .

. . . . . .

3 3 3 3 3 4

. . . . . .

8 hole . . 8 hole . . 10 hole . 12 hole . 14 hole . bars . . .

. . . . . .

. 18-1/2 x 10-5/8 . 18-1/2 x 11 . 19-3/16 x 12-5/8 . 18-3/4 x 22-5/8 . 19-1/4 x 22-3/4 . 19-3/16 x 12-5/8

CHIEF P-30061 . . . . . . . . . . . . . 15 . . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 13 hole . . . . . . . . . . . . . . . . . . 15-3/16 x 10 P-30064 . . . . . . . . . . . . . 17 . . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 4 hole . . . . . . . . . . . . . . . . . . . 19-13/16 x 12-5/8

DAVIDSON P-30068 P-30066 P-30067 P-30544 P-30070

. . . . .

700 500 600 700 901

. . . . .

3 3 3 3 3

. . . . .

13 13 23 23 26

hole . hole . hole . hole . hole .

. . . . .

. 16 x 17-1/4 . 16 x 10 . 13-3/16 x 17-1/4 . 16 x 18 . 16-1/16 x 19-3/4

. . . . . . . . . . . .

500 . . . E47 . . . 600 . . . 600/665 DU34 . . H234 . . 800 . . . C248 . . H234 . . RS34 . . C252 . . 452 . . .

. . . . . . . . . . . .

3 3 3 3 3 3 3 4 4 4 4 4

. . . . . . . . . . . .

5 hole . 7 hole . 5 hole . bars . . bars . . bars . . 8 hole . bars . . bars . . bars . . bars . . bars . .

. . . . . . . . . . . .

. 16-1/2 x 10-1/2 . 16-5/16 x 18-3/8 . 19-1/8 x 12 . 19-13/16 x 12 . 19-3/16 x 12-1/2 . 19-7/8 x 13-1/8 . 16-11/32 x 20-1/4 . 16-5/16 x 18-1/2 . 19-7/8 x 12-5/8 . 19-7/8 x 12-5/8 . 16-3/8 x 20-1/8 . 17-3/4 x 20-1/4

. . . . . . . . . . . . . . . . .

KORD 64 . MO. . . . . . KORS . . . SOR. . . . . SORD . . . SM 102 . . SM 102 . . MO. . . . . . TOK . . . . . GTO 46 . . GTO 52 . . GTO52 . . . SM 52 . . . QM 46DI . QM 46 . . . KORA . . . KORD 62 .

. . . . . . . . . . . . . . . . .

4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4

. . . . . . . . . . . . . . . . .

straight . straight . straight . straight . straight . U bars . straight . bars . . . straight . straight . straight . bars . . . straight . straight . bars . . . straight . straight .

. . . . . . . . . . . . . . . . .

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

. . . . . . . . . . . . . . . . .

. 20-5/8 x 26-1/2 . 22-1/4 x 26-1/2 . 23 x 29-3/8 . 27-1/8 x 33-1/2 . 28-1/8 x 36-1/4 . 32-5/8 x 41-1/8 . 31-1/8 x 41-3/8 . 23-3/4 x 29-3/8 . 16 x 10-1/2 . 17-5/16 x 18-1/8 . 17-1/2 x 20-1/2 . 17-1/2 x 20-1/2 . 18-1/8 x 21-1/16 . 21-7/8 x 13-1/4 . 21-7/8 x 13-1/4 . 20-1/4 x 23-5/8 . 20-1/4 x 24-5/8

HAMADA P-30072 P-30533 P-30074 P-31261 P-31430 P-30538 P-30079 P-31150. P-30597 P-31254 P-31282 P-31290

. . . . . . . . . . . .

HEIDELBERG P-30557 . . P-30558 . . P-30562 . . P-30563 . . P-30564 . . P-31271 . . P-30566 . . P-31422 . . P-30550 . . P-30551 . . P-30552 . . P-30552-B . P-31257 . . P-31287 . . P-30790 . . P-30555 . . P-30510 . .

. . . . . . . . . . . . . . . . .

MULTILITH P-30043 . . . . . . . . . . . . . 1250 . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 9 hole . . . . . . . . . . . . . . . . . . . 15-3/16 x 10 P-30045 . . . . . . . . . . . . . 1250W . . . . . . . . . . . 3 . . . . . . . . . . . . . . 17 hole . . . . . . . . . . . . . . . . . . 16-1/16 x 10-5/8 P-30050 . . . . . . . . . . . . . 1850 . . . . . . . . . . . . 3 . . . . . . . . . . . . . . 30 hole . . . . . . . . . . . . . . . . . . 16-1/16 x 17-5/8

RYOBI P-30081 . . P-30082 . . P-30084 . . P-30085 . . P-30086 . . P-30086-B . P-30087 . . P-30589 . . P-30091 . . P-30568 . . P-30531 . . P-30092 . .

. . . . . . . . . . . .

2700 . . . . . . . 2800 . . . . . . . 2800XL . . . . . 3200 . . . . . . . 3200LC . . . . . 3200LC . . . . . 3200MCD/LC . 3200PFA . . . . 3302 . . . . . . . 3302M . . . . . . 3302M . . . . . . 480/500 . . . . .

. . . . . . . . . . . .

5 5 5 5 5 5 5 5 5 5 5 5

. . . . . . . . . . . .

8 hole . . 8 hole . . 8 hole . . 10 hole . 10 hole . bars . . . 12 hole . bars . . . bars . . . bars . . . 12 hole . 7 hole . .

. . . . . . . . . . . .

.. .. .. .. .. .. .. .. .. .. .. ..

. . . . . . . . . . . .

. 18-1/32 x 10-5/8 . 18-15/16 x 11-1/4 . 19-1/2 x 11-1/4 . 18-15/16 x 12 . 19-1/2 x 12 . 19-1/2 x 12 . 19-1/2 x 13 . 19-1/8 x 12-1/4 . 19-3/8 x 13-5/8 . 19-1/2 x 13-5/8 . 19-1/2 x 13-5/8 . 19-1/8 x 16-7/8

This is just a small sample of our inventory. Call for more part information.

PRESORTED STANDARD U.S. POSTAGE PAID RUTHERFORD, NJ PERMIT NO. 348

PRINTERâ&#x20AC;&#x2122;S PARTS STORE 1 +$<'(1 5' % 6&2776'$/(, $= 800- - FAX - - www.azpressparts.com / sales@azpressparts.com

CALL US FOR MANY â&#x20AC;&#x153;HARD TO FINDâ&#x20AC;? PARTS. WE HAVE OVER 100,000 DIFFERENT ITEMS IN STOCK NOW! VACUUM PUMP REPAIR KITS Consists of all parts neccessary to repair your vacuum pump. For A.B. Dick 350, 360, 375, 9800 P-1182 For A.B. Dick 380, 385 (Air - Vac pumps only) P-1930 For Multilith 1250â&#x20AC;&#x2122;s P-1961 For Chief 15, 115, 215, 17, 117, 217 & Davidson 500, 600, 700, series. P-1960

OFFSET DUPLICATOR LAMPS COMES WITH UNIVERSAL MOUNTING HARDWARE, HAS A FLEXIBLE NECK AND CAN USE UP TO 100 Watt BULB. Includes mounting kit, stud, washer, shoulder nut, nylock nut, and cord. For A.B. Dick, Multilith, Chief, Davidson, and Ryobi P-1956

REPAIR / TROUBLESHOOTING VIDEOS THIS OLD PRESS A professionally made film documenting repairs for the A.B. Dick 350, 360, 375, and 385 presses, and for the Multilith 1250, 1250LW, 1250N, and 1850 presses. VHS-A.B. Dick (English) P-1714 VHS-Multilith (English) P-1715 VHS-A.B. Dick (Spanish) P-30006 VHS-Multiltih (Spanish) P-30005 VHS-Ryobi (English) P-31070 PRO-TIPS 2 tapes with 120 minutes of advanced pressman techniques plus workbook for the A.B. Dick 350, 360, 9800, and 385 presses. VHS P-1717 DONâ&#x20AC;&#x2122;T LET DOWN TIME PICK YOUR POCKET! A BROKEN SCREW OR PIN CAN CAUSE YOUR MACHINE TO BE DOWN AND COST YOU TIME AND MONEY. â&#x20AC;&#x153;QUICK FIX REPAIR KITSâ&#x20AC;? FOR ALL MODELS: A.B. DICK, CHIEF, DAVIDSON, GESTETNER, HAMADA, HEIDELBERG, MULTILITH, RYOBI/ITEK. **** CALL FOR MORE INFO AND PRICES.

ASK US ABOUT OUR REPLACEMENT PARTS MANUALS For A.B Dick chute and chain deliveries - 350, 360, 375, 9800, and (385 Chain delivery only) For Multilith chute and chain deliveries - 1250, 1250W, 1250LW, 1250N, 1250Domestic. For Chief / Gestetner 15, 115, 215, 17, 117, 217, Super Chief 2000, X-series / 211, 213, 311, 312, 313

JOGGERS â&#x20AC;˘ ELECTRIC STAPLERS â&#x20AC;˘ SECOND COLOR HEADS â&#x20AC;˘ SWING AWAY BRACKETS â&#x20AC;˘ NUMBERING UNITS â&#x20AC;˘ REPAIR KITS â&#x20AC;˘ AND MUCH MORE! CALL US AND ASK

WE ALSO HAVE A WIDE VARIETY OF ATTACHMENTS AND ACCESSORIES INCLUDING â&#x20AC;˘ SPRAY UNITS AND POWDERS â&#x20AC;˘ ANTI TRACKING WHEELS â&#x20AC;˘ LIGHT TABLES â&#x20AC;˘ LAMPS â&#x20AC;˘

INK WASH UP ATTACHMENTS â&#x20AC;˘ FOLDERS â&#x20AC;˘ PARTS FOR LARGE AND SMALL FOLDERS â&#x20AC;˘ AUTOMATIC DAMPENING UNITS â&#x20AC;˘ PAPER CUTTERS â&#x20AC;˘ PAPER DRILLS â&#x20AC;˘ PAPER