® Installation Guide CO2LIGHT
Contents
1. Tubes 2. Panels 3. Downlight 4. Streetlight
CO2LIGHT® Gørtlervej 21 DK-‐9000 Aalborg Phone: +45 70 70 15 55 e-‐mail: info@co2light.com
® Installation Guide CO2LIGHT
LED Tubes
Begin the installation by shutting off the power.
Identify what kind of ballast, you are using (magnetic or electronic)
Magnetic ballast: Remove the old starter, and either remove or bypass the magnetic ballast. Only for specific demo and test uses, the ballast can be left in. In any case, the phase compensation capacitor should be removed.
Electronic ballast: Remove the old, electronic ballast.
Adjust the pins by the rotating caps, and insert the tube in the fixture. Remember, that the power should go to the end that says ”power”. It should also be noted that the fixture should be marked according to what end the power comes from CO2LIGHT® Gørtlervej 21 DK-‐9000 Aalborg Phone: +45 70 70 15 55 e-‐mail: info@co2light.com
® Installation Guide CO2LIGHT
LED Panels – Wire Installation Unpack the enclosed driver.
Connect the driver’s brown cord (L) and the blue cord (N) with the spark plug.
Insulate the connection point. Most electricians use cable sleeves with insulation. If in doubt, contact your electrician.
Connect the DC end of the cord to the panel.
CO2LIGHT® Gørtlervej 21 DK-‐9000 Aalborg Phone: +45 70 70 15 55 e-‐mail: info@co2light.com
® Installation Guide CO2LIGHT
LED Panels – Ceiling Assembly Fasten the frame securely to the ceiling. Note, that the screw is going to carry the frame, the panel and the driver.
Inser the panel within the frame
Connect the driver before completing the frame. Use the enclosed plugs. Hide the driver behind the panel. Connection to 230V AC should be in accordance with the specific laws.
Mount and secure the last piece of the frame.
Mound and secure the last piece of the frame
CO2LIGHT® Gørtlervej 21 DK-‐9000 Aalborg Phone: +45 70 70 15 55 e-‐mail: info@co2light.com
® Installation Guide CO2LIGHT
LED Panels – Wall Assembly Fasten the frame securely to the wall. Note, that the screw is going to carry the frame, the panel and the driver.
Do not mount the last piece of the frame yet.
Insert the LED panel within the frame
Connect the driver before completing the frame. Use the enclosed plugs. Hide the driver behind the panel. Connection to 230V AC should be in accordance with the specific laws.
Mount and secure the last piece of the frame
CO2LIGHT® Gørtlervej 21 DK-‐9000 Aalborg Phone: +45 70 70 15 55 e-‐mail: info@co2light.com
® Installation Guide CO2LIGHT
LED Panels – Suspended Assembly
Fasten the wire to the frame
Do a two-‐point mounting
Mount it to the ceiling, with the same distance between the wires as on the panel
Adjust to spirit level.
CO2LIGHT® Gørtlervej 21 DK-‐9000 Aalborg Phone: +45 70 70 15 55 e-‐mail: info@co2light.com
® Installation Guide CO2LIGHT
LED Downlight
Begin the installation by drawing a circle on the ceiling, where to downlight is going to be. The diameter of the circle kan be found in the catalogue (measurement B). Use a saw or some other tool to cut out the circle as shown in the figure.
Attach the power supply to the ceiling, and connect the ac-‐cable to the high-‐tension cable. Note that it should be possible for the power supply to cool off
Connect the DC-‐output to the downlight
Install the lamp, by pressing on the clamps, and pushing it into the hole in the ceiling.
CO2LIGHT® Gørtlervej 21 DK-‐9000 Aalborg Phone: +45 70 70 15 55 e-‐mail: info@co2light.com
® Installation Guide CO2LIGHT
LED Streetlights
Link the terminal plugs of the streetlight and the terminal block in the pole (brown to brown, blue to blue, yellow to yellow and green to green). Then close the PC cover after linking the plugs securely. Lastly put the terminal block wiring back into the pole. Always use officially approved assembly units (isolated). If you are in doubt, contact your electrician.
Loosen the screws on the lamp, and connect it to the pole
Fasten the screws, and thereby finalize the connection with the pole.
CO2LIGHT® Gørtlervej 21 DK-‐9000 Aalborg Phone: +45 70 70 15 55 e-‐mail: info@co2light.com