IEP TECHNOLOGIES

Sound explosion prevention and protection strategies are needed, especially for the most susceptible areas of a pellet plant. Explosion Protection for Dust Collection

Dust explosions and fires in the biomass industry, including pellet manufacturing plants, are not unusual occurrences. The elements needed for an explosion, usually multiple things working together—fuel, oxygen, confinement and dust dispersion—can originate in multiple equipment areas within the facility: hammermills, conveyors, dryers, coolers or storage vessels. After that, the only missing ingredient needed for a potentially devastating explosion is an ignition source. One process vessel most prone to dust explosions is the Air-Material Separator (AMS), which in a pellet plant can be a dust collector/baghouse or cyclone.

The purpose of the AMS is to separate the fines from the airstream, which makes these vessels among the most susceptible to explosions within the entire process. The driest and finest dust within the process stream is usually found in these vessels—the smaller and drier the particle, the lower the ignition energy required to initiate an Grandaw

event. Adding to this threat is the smaller the particle size for a given product, the more surface area by volume is available for heat absorption, resulting in a more dynamic explosion with a higher deflagration index. Another significant risk is that many pellet processes use a central dust collector, aspirating off several vessels. An explosion in the dust collector can propagate through the inlet duct to multiple vessels upstream, causing secondary explosions with devastating results.

For any facility, the first line of defense must be prevention. This should include many of the following practices: • Proper grounding and bonding for static control • Magnetic separators or other means to identify and remove tramp metal • Bearing temperature monitoring or linear heat detection • Electrical equipment rated for the hazard area • Housekeeping to minimize residual dust buildup • Spark detection and suppression on conveyors and dust lines • Hazardous awareness training

A dust hazard analysis (DHA) should be conducted to identify areas of risk within the facility and indicate strategies to minimize the potential for an explosion during normal operating and upset conditions. Because abnormal conditions can happen, NFPA 652 (Fundamentals of Combustible Dust) and NFPA 664 (Wood Processing Facilities) require that the AMS be equipped with explosion protection. The most common forms of protection found in pellet plants are explosion venting, flameless venting, suppression and isolation.

Explosion vents are panels that are strategically located on the sides of the baghouse, or on top of the cyclone. These panels rupture from deflagration pressures, creating an opening that will release a fireball as well as burnt and unburnt dust. Venting is designed to reduce the pressure buildup within the protected vessel to below that which would cause vessel rupture. Typically, vents are of two styles: flat (normal for baghouses) or domed (an option for pressure-cycling vessels).

When considering explosion vents, the most important factor must be whether the vented fireball can be directed to a safe outside area where no equipment, buildings or personnel may be

Explosion isolation extinguisher on a dust collection line at a DRAX pellet plant. PHOTO: IEP TECHNOLOGIES

No matter what you’re processing – chemicals, food, pharmaceuticals, biomass, wood products – if it produces dusts or powders, there’s a high probability you have an explosion risk. All it takes to interrupt your plant productivity is a combustible material, oxygen and an ignition source. For more than six decades, IEP Technologies has provided the right explosion protection solution for every type of process application. From cyclone separators and dust collectors to milling equipment and dryers. We can analyze your challenge, design a protection system and surround you with 24/7 service and support. Protecting your plant starts with knowing your explosion risk.

Let’s develop an explosion protection solution for you

Call the IEP engineering experts with the most experience in explosion protection at 1-855-793-8407 or visit IEPTechnologies.com.

Graphic illustrating an explosion suppression system on a baghouse. IMAGE: IEP TECHNOLOGIES

present. The fireball from a vented explosion can eject 50 feet or more. Flame ejection calculation formulas are found in NFPA 68 (Deflagration Venting).

Flameless venting combines an explosion relief vent with a metal mesh trap. Like a standard explosion relief vent, the flameless vent's membrane, installed on the process vessel, opens during a deflagration. But unlike a standard relief vent, the flame and most of the heat from the deflagration is absorbed by the mesh trap, with the deflagration overpressure discharged outside the vessel. Note that a safety perimeter must still be established around the flameless vent to protect workers from the discharge.

An explosion suppression system detects the incipient deflagration and, within milliseconds, injects a dry chemical extinguishing agent into the protected vessel to suppress the explosion before damaging pressure buildup can occur. These systems typically use pressure sensors as a means of detection. Static detectors with a set pressure setting have been commonly used in the past, but rate-ofpressure-rise detectors are becoming much more prevalent due to their high immunity against inadvertent operation from normal operating pressure fluctuations.

Regardless of the protection solution used, flame propagation to connected vessels remains a high threat unless explosion isolation is installed. Passive solutions can include a rotary gate valve that meets the requirements of NFPA 69 (Explosion Prevention), or a flap-style isolation valve on the AMS inlet. Flap valves are closed by the pressure wave preceding the flame propagating through the duct, to prevent the fireball from moving further upstream. When considering flap-style isolation valves, care must be taken to ensure that the valve is designed and approved for the specific application.

Two active explosion isolation techniques are also options. Chemical explosion isolation is typically used in conjunction with explosion suppression systems, or on vessels equipped with explosion venting where flap valves cannot be employed, such as on vertical ducts. High-speed gate valves can also be used for isolation, although because of their cost, these valves are less frequently employed in pellet plants than other isolation techniques.

While the AMS is critical to maintain good housekeeping and reducing the risk of a secondary explosion inside the facility, it is one of the most susceptible vessels to an explosion at the plant. Developing sound explosion prevention strategies, combined with suitable explosion protection, will help limit the explosion risk to operators and the facility.

Contact: David Grandaw Vice President of Sales IEP Technologies david.grandaw@hoerbiger.com

Book Your Ad AD SPOTS LIMITED

Ad Deadline: Oct. 28, 2020 Mailed with Issue 1, 2021 ofPellet Mill Magazine

Reach Producers

REACH 8,000 PROFESSIONALS  All Biomass Magazine subscribers  All Pellet Mill Magazine subscribers  Pellet mill owners, operators & management  All major related conferences

PURCHASE A SPOT ON THE PELLET PRODUCER MAP Receive 12 Months FREE Online Advertising! Advertise now on Pellet Mill Magazine’sU.S. & Canada Pellet Producer Map. It is the easiest and most cost-effective way to get your name, product and/or service in front of Pellet Producers, as well as other industry professionals for 12 months at a time.

Need more info on advertising opportunities? service@bbiinternational.com - 866-746-8385 - BiomassMagazine.com

Erin P.B. Zasada

John D. Schroeder

International Biomass Conference & Expo

for Used Dumpers/Tippers, all Brands Stationary or Portable WE PAY CASH

SPONSORED SPO TLIGHT

Airofl ex Equipment Portable Trailer Tipper

Engineered with a rugged design, our portable trailer tipper can tackle the most challenging applications with a 10’ x 45’ platform, 45-ton lifting capacity, 63-degree tilt and a 2-minute up-cycle time. Designed for simple off-highway movement, it can be prepped for over-the-road transport. An electric hydraulic power unit comes standard, or a diesel power unit is also available.

563-264-8066 sales@airofl ex.com airofl ex.com

Biomass Magazine’s Products & Services Spotlight Feature

As a Spotlight Feature you will receive the following: • A custom story written in the Products and Services Spotlight feature article containing information about your company • Mailed to 7,000 readers • Sent to 61,000+ biomass email subscribers, promoting the products and services

Contact us for more information: 866-746-8385 service@bbiinternational.com

731-593-3426

bohobbs@bellsouth.net www.aminternationaltnllc.com

International Biomass Conference & Expo

The 14th annual International Biomass Conference & Expo will take place March 15-17, 2021, in Jacksonville, Florida. This dynamic event unites industry professionals from all sectors of the world’s interconnected biomass utilization industries—biobased power, thermal energy, fuels and chemicals.

866-746-8385 service@bbiinternational.com www.biomassconference.com

American International TN LLC

Here at American International TN LLC, we've got you and your needs covered. You see, we've been in the equipment business for years & now we are selling hydraulic truck dumpers & tippers for semi-trucks & trailers and we've got the experience that it takes to be the best in the bulk material handling equipment industry.

731-593-3426 bohobbs@bellsouth.net www.aminternationaltnllc.com

'™>AA}wq'Zq'U RESERVE YOUR BOOTH TODAY

14th Annual

TīÆìǪǮȤǪǰ 2021 Prime F. Osborn III Convention Cente r JACKSONVILLE, FL

The biomass industry is changing fast, and the best way to capitalize on new opportunities and overcome new challenges is to get educated. Leverage AĊĴÐīĊĴðďĊă ðďĉĮĮďĊåÐīÐĊÆÐɴ 'ŘĨď community of producers, partners and industry experts during three days of learning, sharing, and connecting to strum up your business.

”>'t'qtZ#€'twT''} PELLETS DENSIFIED BIOMASS BIOMASS POWER BIOMASS THERMAL BIOGAS & RNG WASTE-TO-ENERGY ADVANCED BIOFUELS BIOBASED CHEMICALS

ȮA'ǫǪ twitter.com/biomassmagazine 866-746-8385 service@bbiinternational.com

3URGXFHG%\