HomeWorks®
RF DIMMERS
Lamp Dimmers 048-017 1a 04.21.03
HomeWorks RF Lamp Dimmer
DESCRIPTION
Indicator Lights
Tapswitch
HomeWorks RF Lamp Dimmers, used in both localized and optimized lighting control designs, function much like standard dimmers and switches, and have an integral microprocessor, allowing them to be incorporated into the whole-house lighting control system. Communications with the system is accomplished via radio frequency (RF). RF Lamp Dimmers are useful in locations where single plug-in lamps need to be dimmed or switched. RF Lamp Dimmers incorporate advanced features such as fade on/ fade off, slow fade off, and rapid full on.
Raise/Lower Rocker
Lamp Cord Receptacle
120VAC Plug
HTR-3LD-SW
MODEL NUMBERS RF Lamp Dimmer HTR-3LD-XX 300W Incandescent, 300VA Mag. Low Voltage “XX” in the model number represents color/finish code.
® JOB NAME:
JOB NUMBER:
SPECIFICATION SUBMITTAL MODEL NUMBERS:
Page
HomeWorks®
RF DIMMERS
Lamp Dimmers 048-017 2a 04.21.03
S P E C I F I C AT I O N S
• On a double-tap, lights go to full ON.
COLOR / FINISH CODES
Regulatory Approvals
• Pressing and holding the tapswitch slowly fades lights to OFF, beginning at press.
Faceplate Color
• UL Listed. • CSA Certified.
• Light levels can be fine-tuned by pressing and holding the raise/lower rocker until the desired light level is reached.
• FCC Compliant. Complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Satin Colors® Snow Midnight
(code)
(SW) (MN)
System Communications and Capacity
• Industry Canada Registered. Power Operating voltage: 120/127 VAC, 50/60 Hz.
• RF Lamp Dimmers communicate with the HomeWorks RF processor through radio frequency (RF). • Each HomeWorks RF processor is capable of directly controlling up to 64 RF dimmers.
Key Design Features • Green indicator lights.
Environment
• Power failure memory: should power be interrupted, the lights will return to their previously set level prior to the interruption when power is restored.
Ambient operating temperature: 0-40°C, 32-104°F, 0-90% humidity, non-condensing. Indoor use only.
• Six-foot (1.8m) cord length. • Tapswitch is programmable. • On a single tap, lights fade up or down.
I N S TA L L AT I O N Plug lamp cord into back of RF Lamp Dimmer plug. Plug RF Lamp Dimmer plug into any standard wall outlet.
® JOB NAME:
JOB NUMBER:
SPECIFICATION SUBMITTAL MODEL NUMBERS:
Page
HomeWorks速
RF DIMMERS
Lamp Dimmers 048-017 3a 04.21.03
DIMENSIONS Side View
Front View
15/16 in. (24mm) Cord Length: 6 ft. (1.8m)
4-11/16 in. (119mm)
11/16 in. (17.5mm)
2-15/16 in. (75mm)
D I M M E R L OA D T Y P E A N D C A PAC I T Y
D I M M E R O P E R AT I O N Status LEDs (Dimmer only) Indicate light level; glow softly as night light when light is off Dimming Rocker Press to Brighten Press to Dim
Load Type
Capacity
Incandescent
300 W
Magnetic Low-Voltage
300 VA
Tapswitch Tap on/off
速 JOB NAME:
JOB NUMBER:
SPECIFICATION SUBMITTAL MODEL NUMBERS:
Page
HomeWorks®
RF DIMMERS
Lamp Dimmers 048-017 4a 04.21.03
Home A: 2500 sq. ft. (232m ) or less - all RF devices within 30 ft. (9m) of RF Processor 2
SY S T E M C O M M U N I C AT I O N N OT E S
RF Lamp Dimmer
RF Maestro Dimmer
RF Designer-Style Keypad
• RF Lamp Dimmers must be located within 30 feet (9m) of an RF Signal Repeater or an RF Processor. Multiple repeaters may be necessary to provide adequate coverage. • RF Dimmers cannot be controlled by the system and RF Keypads will not function until they are addressed and programmed. See the HomeWorks Utility online help.
30 Feet (9m) maximum RF Processor Home B: 2500 sq. ft. (232m2) or greater - some RF devices more than 30 ft. (9m) from RF Processor RF Lamp Dimmer 30 Feet (9m) maximum
RF Signal Repeater RF Maestro Dimmer
RF Designer-Style Keypad RF Processor
60 Feet (18m) maximum between RF Processors and Repeaters
30 Feet (9m) maximum
® JOB NAME:
JOB NUMBER:
SPECIFICATION SUBMITTAL MODEL NUMBERS:
Page