Section 13 - Pumps, Plumbing & Gallery by BLA

section

Whale IC Pumps & Accessories Pressure Pumps & Washdown Pumps Grey & Black Waste Pumps Manual Bilge Pumps & Accessories - Whale/Henderson Diverter Valves & Strumboxes Electric Bilge Pumps & Float Switches Aerator Pumps & Accessories Grey Waste Sumps Galley Pumps & Accessories, Deck Wash Fittings Taps & Shower Fittings Hot Water Systems Sinks & Wastes Hose Quick Connect 15 Plumbing Water Tanks & Solar Shower Skin Fittings, Valves,Tails & Hose Connectors Hose Clamps Strainers & Scuppers Waste Holding Tanks & Toilet Accessories Toilets & Accessories Galleymate Gas Barbecue Magma Barbecues & Mounts Regulators & Magma Cook Ware Magma Tables & Mounts

172-173 174-175 176 177-179 180 181-184 184-186 187-188 188-191 192-197 198 199 200 201-203 203 204-209 205 210 211 212-214 214 215-219 220 221-222 www.bla.com.au

PUMPS, PLUMBING & GALLEY

171

section

PUMPS, PLUMBING & GALLEY

Whale Intelligent Control A New Era of Fresh & Waste Water Control on Board Whale has developed a revolutionary and innovative range of pumps and accessories which use a built in electronic control circuit to communicate directly with each other. Known as Intelligent Control (IC) this complete system allows the built-in software to control the pumps automatically in reaction to the accessory commands. The IC technology is not just an on/off pump control but a complete monitor of all relevant aspects of the system. Intuitive IC pumps are matched with IC accessories such as shower gulley’s, manifolds and bilge strainers which sense waste and bilge levels, alerting the Gulper IC and providing automatic operation. The new Fresh IC freshwater pump monitors voltage, pressure and current and provides for soft start and stop running with no mechanical switching, meaning less on/off cycling and longer system life. The new IC technology monitors relevant aspects of the system via integrated sensors with no moving parts. Designed with reliability in mind all IC components are fully protected against water ingress with fully potted circuitry. High integrity pre wired connection systems feature marine grade waterproof electric connectors for quick and easy fit up. With continuous monitoring and self diagnosis the pump performance is continually scrutinised and adjusted depending on demand and supply voltage.

Gulper® IC High capacity grey waste pump with Intelligent Control electronics built in ensuring that the pump operates only when required. When grey water is detected via an electronic signal received from either the Gulley IC or Two Way Manifold IC, the Gulper IC pump is automatically activated, minimising wear and reducing operating times. Features: • Automatic control receives electrical signals to turn on/off as required • Soft start protects the pump for long life • Electronics enable use with lower current switches • Electronics are all internally housed • One pump handles waste from multiple drains • Fast drainage with high capacity up to 19l/m • Self primes and runs dry without damage • Easy to install, even on uneven surfaces

BLA Power Capacity Code V Amp l/m g/m 132020 12 7.5 19 5 132026 24 3.25 17.4 4.6 132090 6m extension cable

Max Hose Head Size m mm 3 19/25 3 19/25

Fresh IC The new Fresh IC freshwater pressure pump with Intelligent Control electronics built in prevents rapid cycling without sacrificing flow and performance to revolutionise pump and system control. The Fresh IC not only monitors pressure, but also energy consumption and flow to provide a stabilised water system. Features: • Eradicates water cycling, hammering and power spikes • Maintains performance and pressure throughout the system • Maintains flow in restrictive systems • Soft start - protects the pump for long life • High performance at a range of outlets • Runs dry without damage • Consistent flow even at high back pressure • Eliminates the need for an accumulator tank • Strainer included BLA Volt Open No. of Max. Lift Cut Out Code Flow Outlets Head Pressure I/m m m bar psi 133260 12 14 3-4 133264 24 14 3-4 133268 12 19 5-6 133272 24 19 5-6 133252 Filter assembly 136653 1/2" BSP tail 136657 13mm barbed hose tail 132090 6m extension cable

172

Quality marine equipment

40 40 40 40

3 4.3 3 4.3 3 4.3 3 4.3

62 62 62 62

136653

136657

133252

section

Two Way Manifold IC

The new Strainer IC with integral automatic Intelligent Control provides for quick system fit-up and connection. It operates by sending signals to a remotely mounted Gulper IC pump switching it on and off automatically when water is detected. Supplied with 4m of cable for direct connection to Gulper IC.

The Two Way Manifold IC unit consists of two waste inputs and one outlet with Intelligent Control built in. The intelligent built-in IC design allows waste from multiple drains to be detected, automatically activating the remote Gulper IC pump. Supplied with 4m of cable for direct connection to Gulper IC.

Features: • Small footprint strainer fits into very confined bilge spaces • Low current controlled switching means no burn outs from high currents • On/off delay prevents cycling • Environmentally friendly with no toxic mercury component • Non choke valves with no filter to block or clean • Easy to install, even on uneven surfaces

BLA Code

Hose Length Width Height Mount Size Screws mm mm mm mm mm

19 148 131672 132090 6m extension cable

Hose Width Height Depth Mount Size Screws mm mm mm mm mm

132070 132074 132080 132090 6m

4 r/h

PUMPS, PLUMBING & GALLEY

Strainer® IC

19 140 25 140 38 140 extension cable

114 114 114

103 103 103

5 r/h 5 r/h 5 r/h

Shower Wastes The Whale range of shower wastes (also knows as Gulley's) are available in two sizes to suit 19mm hose in both IC and non IC versions. Features include modern compact design, easily removed cover for cleaning and simplistic mounting. IC models are pre-wired with 4m of cable for direct connection to Gulper IC and are supplied with hose tail and non-return valve as shown in the line drawings below.

134372

134370

42mm (1.65")

25.5mm 19mm (1") (0.75")

51mm (2")

BLA Size Code

134370 Small No 134372 Large No 134382 Small Yes 134384 Large Yes 132090 6m extension cable

19mm 62mm 41mm

25mm

200mm (8") 82mm 76mm 342mm (13.5")

141mm (5.5") 205mm

www.bla.com.au

173

section

PUMPS, PLUMBING & GALLEY

Whale Universal Pressure Pumps Supplied with Quick Connect inlet and outlet for fast connection directly to System 15 plumbing. Includes pre strainer/filter that pivots to suit plumbing direction. 2 x 13mm barbed hose connections and 2 x 1/2" BSP threaded tails also included for connection to non Quick Connect 15 plumbing. Features: • Probably the marine world’s quietest range of pressure pumps • A range of models for two, four and six outlet or wash down application in 12 or 24 volts • Capacity of 8, 12 and 18 litres per minute • Universal mounting feet arrangement fits almost any existing pressure pump mount hole configuration • Suitable for use with fresh or saltwater • Smooth constant flow • Can be run dry without damage • Extra protection and safety with wires and pressure switch housed internally • Self priming up to three metres • Aluminium motor housing • Run indicator wire allows tell tale light and/or buzzer to operate remotely Pump Head Materials: • Glass filled polypropylene, neoprene, nitrile, stainless steel, butyl

136653

136657

133252

Typical installation

230

240 - 18L model 175

220 - 9L & 12L model

125

BLA Volt Code 133230 133233 133234 133235 133236 133251 133252 136653 136657

174

12 24 12 12 24

Open No. of Max. Flow Outlets Head l/m m 8 12 12 18 18

2-3 3-4 3-4 4-6 4-6

30 30 30 30 30

Replacement pump head assembly Filter assembly 1/2" BSP tail 13mm barbed hose tail

Quality marine equipment

Lift

Cut Out Pressure m bar psi 3 3 3 3 3

3 3 3 3 3

45 45 45 45 45

section

Whale High Pressure Washdown Kit The Whale universal high pressure washdown pump delivers up to 18 litres per minute to a maximum pressure of 45psi making light of the most difficult cleaning and washing jobs.

PUMPS, PLUMBING & GALLEY

Designed for salt water use these rugged self priming pumps provide a smooth constant flow to a maximum lift of three metres and can run dry without damage. The glass filled polypropylene head with sealed internal pressure switch are designed to provide years of trouble free use. Supplied as a complete kit which includes a quality, trigger action deck wash hose nozzle to suit 1/2" I.D. hose. Other fittings include pivoting strainer filter and two ¾" flexible hose adaptors. Available in 12 and 24 volt. Two year warranty. Features: • Universal mounting feet arrangement fits almost any existing pressure pump mount hole configuration • Suitable for use with fresh or saltwater • Smooth constant flow • Can be run dry without damage • Extra protection and safety with wires and pressure switch housed internally • Self priming up to three metres • Aluminium motor housing • Run indicator wire allows tell tale light and/or buzzer to operate remotely Pump Head Materials: • Glass filled polypropylene, neoprene, nitrile, stainless steel, butyl

133201

230

240 - 18L model 175

220 - 9L & 12L model

125

BLA Volt Code

Open Flow l/m

Max. Head m

Lift

ut Out C Pressure m bar psi

133290 12 133292 24

18 18

30 30

3 3

45 45

133201 Deck wash nozzle complete

www.bla.com.au

175

section

PUMPS, PLUMBING & GALLEY

Gulper 320 High Capacity Grey Waste Pump The Gulper 320 self-priming pump is specifically designed to pump waste grey water from the shower tray, galley sink or to be used as a small bilge pump. Adjustable clamping ring allows the head assembly to be rotated 360º to accommodate plumbing position. Suitable for either 19mm or 25mm hose connection. Features: • Quiet running • Self priming to 3 metres • Large single diaphragm • Dual non-choke valves • Pumps a mixture of air and water • Secure mount - new wrap around mounting feature Capacity: • 19 l/m @ open flow 19mm hose • Maximum lift 3 metres • Maximum head 3 metres • Lift and head combined 4 metres Materials: • Made from glass filled nylon, acetal, EPDM, stainless steel, santoprene, brass, and aluminium

BLA Power Length Width Height Mount Screws Code Rating V amp mm mm mm gauge 132014 12 7.5 132015 24 3.25 131336 Service Kit

280 280

200 200

115 115

4 r/h 4 r/h

Gulper Toilet Pumps Large capacity heavy duty black waste pump. The large inlet/outlet and free flow valve design allows the pumping of unmacerated toilet waste. Tails suit 38mm hose. Features: • Brass gear drive • Quiet operation • Can be run dry • Large single diaphragm • Pumps a mixture of air and water • Self-priming to three metres • Rotatable inlet/outlet to suit installation Capacity: • 18 l/m @ open flow • Lift 3 metres • Head 3 metres • Lift and head combined 3 metres Materials: • Glass filled nylon, EPDM, nitrile rubber, hypalon, acetal, bronze, stainless steel, brass and aluminium

BLA Power Length Width Height Mount Code Screws v amp mm mm mm mm 132010 12 5 132012 24 2.5 131332 Service kit

176

287 287

Quality marine equipment

360 360

117 117

4 r/h 4 r/h

section

Chimp Mk1 Manual Pump

BLA Capacity Code l/m g/m 131002

27 6

Max. Lift m

Max. Hose Head Size m mm

Mount Screws mm 6 r/h

(A)

Spare Parts: 131193 Diaphragm neoprene 131194 Diaphragm nitrile 131202 Service kit - neoprene 131204 Removable handle (item A) 131206 Removable handle base kit (items included in B) 131208 Spare fixed handle (items included in C)

285 137

187

N.B. Capacity measured at 60 strokes per minute.

230

Compac 50 Manual Pump Designed specifically for low profile installations where space is limited. Quick and easy to fit and offers a wide variety of possible installation configurations. Suitable for saltwater, bilge water and even diesel.

275

Features: • Mounting hole positions are square - giving a choice of pump stroke directions relative to the position of the deckplate • Inlet and outlet mount bases are set at 45º relative to the pump body and have a square base that can be rotated, giving four possible hose directions on each side • Pump body can be rotated to accommodate different hose direction requirements • Supplied complete with deck plate Constructed from stainless steel, glass reinforced polypropylene, acetal copolymer, nylon, PBDT, nitrile and EPDM rubber.

166 103x120

121

210

BLA Capacity Code l/m g/m 131012

43 9.5

Max. Lift m

Max. Head m

Hose Mount Size Screws mm mm 25

PUMPS, PLUMBING & GALLEY

Compact in size, the Chimp Mk1 offers a high output and is ideal for small craft. The valve design gives the Chimp Mk1 a smooth and even pumping action. The clamping screws are easily removed allowing a choice of flow direction and access for servicing. Used extensively in the portable toilet industry as a toilet flushing pump. Suitable for saltwater and bilge water. Made from stainless steel, acetal copolymer, glass reinforced nylon, nitrile and neoprene rubber.

6 c/s

Spare Parts: 131230 Service kit - nitrile 131231 Deck plate kit 131232 Spare removable handle N.B. Capacity measured at 60 strokes per minute.

Gusher Urchin Manual Bilge Pumps

125

280

395

Manual bilge pumps for small to medium sized craft. These sturdy pumps are self-priming. Handles can be orientated in 133 any direction and the diaphragm can be easily accessed for maintenance or removing debris. Stepped hose attachments 170 248 allow either 25 or 38mm hose connection. Suitable for 131045 saltwater, bilge water, waste water and effluent. Made from acetal copolymer, glass filled polypropylene, nylon, stainless steel and neoprene. Nitrile rubber service kit available for use with oils and diesel.

220

277 140 131044

248

220

400

BLA Handle Capacity Code l/m g/m

Max. Lift m

Max. Head m

Hose Size mm

Mount Screws mm

131044 Fixed 47 10 131045 Through deck 47 10 131046 Removable 47 10

4 4 4

3 3 3

25/38 25/38 25/38

6 r/h 6 c/s 6 r/h

152 248

131046

Spare Parts: 131300 Service kit - nitrile 131301 Service kit - neoprene 131302 Spare removable handle 131304 Fixed handle kit 131306 Removable handle kit 131308 Clamp ring kit above deck 131312 Clamp plate kit 131320 Diaphragm neoprene N.B. Capacity measured at 60 strokes per minute with 38mm hose.

www.bla.com.au

177

section

PUMPS, PLUMBING & GALLEY

Mk5 Single Action Manual Pump The free flow valve design makes the Mk5 ideal for a variety of pumping applications such as bilge, diesel transfer, emptying effluent tanks and vacuum toilet pump out. Suitable for both floor and bulkhead installations and can also be converted to through deck installation. The quick release cover makes for easy access and inspection of the diaphragm and valves, as well as clearing obstructions. Constructed from stainless steel, phosphor bronze, acetal, glass reinforced polypropylene and nitrile rubber. BLA Capacity Max. Max. Hose Code Lift Head Size l/m g/m m m mm 131016 56 12.3

4.5

470

205

141

260

Mount Screws mm

220

6 r/h

131150 Through deck conversion kit Spare Parts: 131240 Service kit - nitrile 131242 Spare removable handle 131243 Rocker arm assembly - through deck 131244 Rocker arm assembly kit - bulkhead mount 131246 Diaphragm plate and pivot 131249 Diaphragm only â&#x20AC;&#x201C; nitrile N.B. Capacity measured at 60 strokes per minute.

131150

Toilet Waste Pump

240

Principally used as a manual toilet waste pump. The free flow valve design and quick release inspection cover makes this pump ideal for a variety of applications such as bilge, diesel transfer, emptying effluent tanks and vacuum toilet pump out. White ABS plastic housing keeps in nasty smells. Constructed from stainless steel, phosphor bronze, acetal, glass reinforced polypropylene, glass reinforced nylon and nitrile rubber.

470

205

BLA Capacity Max. Max. Hose Code Lift Head Size l/m g/m m m mm 131019 56 12.3

4.5

Mount Screws mm

141

202

6 r/h

Spare Parts: 131240 Service kit - nitrile 131242 Spare removable handle 131244 Rocker arm assembly kit - bulkhead mount 131246 Diaphragm plate and pivot 131249 Diaphragm only â&#x20AC;&#x201C; nitrile N.B. Capacity measured at 60 strokes per minute.

Mk5 Double Action Manual Pump The Mk5 double action pump consists of two Mk5 pumps mounted back to back and operated by the one handle. It may be fitted either to the floor/deck, or through the deck with purchase of optional through deck conversion kit. Twin diaphragms allow the Mk5 double action pump to empty two separate bilge compartments at the same time, or one twice as quickly using the two manifolds supplied. Even if one bilge runs dry, pumping of the other can continue unimpaired. Suitable for saltwater, bilge water, waste water, effluent and diesel. Made from aluminium alloy, stainless steel, phosphor bronze, acetal copolymer, polypropylene, nitrile rubber and neoprene rubber.

700

253

280

BLA Capacity Max. Max. Hose Code Lift Head Size l/m g/m m m mm 131022 104 23

4.5

131150 Through deck conversion kit Spare Parts: 131250 Service kit - nitrile 131254 Rocker arm kit 131256 Clamp plate kit N.B. Capacity measured at 60 strokes per minute.

178

Quality marine equipment

Mount Screws mm 8 r/h

224

section

Gusher 30 Manual Bilge Pump The Gusher 30 is the largest capacity manual pump in the Whale range. Made from anodised and epoxy coated marine grade LM6 aluminium alloy. Floor/deck or through deck mounted with purchase of optional through deck conversion kit.

PUMPS, PLUMBING & GALLEY

Features: • Neoprene valves and diaphragms • Twin diaphragms (retains suction even if one diaphragm is damaged) • Easy access for cleaning and servicing via large nylon hand nuts (no tools required) • Free flow, non choke valves • Stainless steel fastenings • Acetal copolymer bushes • Suitable for survey vessels

760

330

265

BLA Capacity Code l/m g/m 131030

100 22

Max. Lift m

Max. Hose Head Size m mm

Mount Screws mm

233

8 r/h

131154 Through deck conversion kit Spare Parts: 131260 Service kit - neoprene 131262 Spare removable handle 131264 Gaiter kit N.B. Capacity measured at 60 strokes per minute.

Gusher 10 Mk3 Manual bilge Pump A bilge pump with a world wide reputation for reliability. The large valves ensure smooth flow and reduce the likelihood of blockage by any stray debris in the bilge water. Used extensively for manual pump-out of effluent holding systems. Variable mounting positions enable the pump to be installed either on bulkhead, floor or through deck with the purchase of optional through deck kit. The design gives instant access to all parts for maintenance. Made from epoxy resin coated alloy, stainless steel, and neoprene rubber. Suitable for use with oils and diesel transfer if fitted with nitrile service kit.

440

204

BLA Capacity Code l/m g/m

Max. Lift m

Max. Hose Head Size m mm

Mount Screws mm

131034 55 12 4 4 38 131156 Through deck conversion kit - alloy 131158 Through deck conversion kit - plastic

8 r/h 196

Spare Parts: 131280 Service kit - nitrile 131281 Service kit - neoprene 131282 Spare removable handle 131284 Eye bolt assembly

317

N.B. Capacity measured at 60 strokes per minute.

Gusher Titan Manual Bilge Pumps The Titan is a very powerful, compact bilge pump available in a choice of bulkhead or through deck mount. Its large, single pump chamber and generous valve ports have been designed to give a smooth, high volume flow rate. The diaphragm and handle assembly can be rotated for variable pumping positions. Suitable for saltwater, bilge water, waste water and effluent. Nitrile service kit available for use with oils and diesel. Made from moulded acetal copolymer, glass filled polypropylene, nylon, stainless steel, chromed phosphor bronze, nitrile and neoprene rubber.

440 208

239

BLA Mount Capacity Code l/m g/m

Max. Lift m

Max. Head m

131038 Bulkhead 89 19.5 131039 Through deck/bulkhead 89 19.5

4 4

Spare Parts: 131282 Spare removable handle 131290 Service kit - neoprene 131292 Clamp plate kit 131296 Bulkhead clamp ring kit

Under deck lever kit Service kit - nitrile Rocker arm kit Under deck clamp ring kit

131283 131291 131294 131298

131038

510

Hose Mount Size Screws mm mm 38 38

370

200

6 r/h 6 c/s

280 131039 131038

N.B. Capacity measured at 60 strokes per minute.

www.bla.com.au

179

section

PUMPS, PLUMBING & GALLEY

Piping Connectors

Non-Return Valves

The ‘Y’ piece and 90º elbow are useful in many bilge pump installations. The ‘Y’ piece enables two pumps to discharge through a single line when a diverter valve is not required. The elbows are helpful in confined spaces, they have one external end to clamp over a Whale/ Henderson manual bilge pumps inlet or outlet, the other end fits internally in hose of the size as normally connected to the bilge pump, thus providing a 90º plumbing bend at hose to pump connection.

The Whale non-return valves offer a simple way to maintain prime in a suction or discharge line. Designed to fit in-line, they can also be dismantled for ease of cleaning. 131114 accepts 25mm hose but can be cut to accept 38mm hose. Totally non corrosive construction.

BLA Code

Hose Size mm

131102 131104 131106

25 38 38

131112 131106

131114

Max. Max. Length Width mm mm 45 60 128

131104

BLA Code

Length mm

Width mm

131112 131114

89 127

32 45

131229 Replacement valve for 131114

• Allows one pump to draw from two locations • Teflon lubricated smooth lever operation 180

BLA Code 131124 131126 131116 131118

BLA Entry Length Width Height Code mm mm mm 120 56

58 104

Mount Screws mm 5 r/h 5 r/h

Superseded Whale/Henderson Pump Spares BLA Description Code 131188 131189 131190 131197 131198 131199 131220 131222 131227 131228 131229 131270 131324

180

Whale/Henderson Number

Chimp Mk 1 & 2 diaphragm stud Chimp Mk 1 & 2 diaphragm plate Chimp Mk 1 & 2 diaphragm nut Chimp Mk 1 & 2 fulcrum pin Chimp Mk 1 & 2 hinge pin Chimp Mk 1, 2 & Urchin circlip Chimp Mk 2 neoprene service kit Chimp Mk 2 nitrile service kit Chimp Mk 2 neoprene diaphragm Chimp Mk 2 inlet valve Chimp Mk 2 outlet valve Gusher 25 nitrile service kit Gusher 8 Mk 3 neoprene service kit

Quality marine equipment

19 25/38

High quality two-way valves, normally installed in the suction or discharge line of bilge pumps, they also have many other uses including toilet waste diversion. They are precision machined to eliminate seepage and odour problems.

Fitted at the end of a manual bilge pump suction hose deep in the bilge, a Whale strumbox prevents debris from entering and blocking the hose or bilge pump. Available in top entry for deeper bilges or side entry for shallow bilges. They are suitable for 25mm hose and can be cut to accept 38mm hose. • Allows maximum amount of water to be pumped from the bilge • Fitted non-return valve prevents drain back • Removable strainer for ease of cleaning • Pump out of bilge water as shallow as 5mm

170 147

32 53

Diverter Valves

54 75 99

Strumboxes

131116 Side 131118 Top

Height Hose Size mm mm

405.03 405.04 405.05 406.45 406.46 733.40 AK8015 AK8017 406.37 733.08 733.09 AK3528 SK8813

Hose Width Height Depth Size mm mm mm mm 25 38

139 159

146 153

103 103

Mount Screws mm 5 r/h 5 r/h

‘Y’ Valve Provides controlled diversion of 2 x 38mm lines into one or vice versa. Typical uses include connection of one bilge pump to two separate bilge areas or installation in a toilet system to control discharge to holding tank, or deck waste pump out, or discharge overboard (if permitted). Manufactured from ABS plastic to retain odours. Stainless steel fastenings used throughout. Locking tab enables the valve to be locked in one line open position. Valve configuration has common port always open with one of the other ports selectably open or both open. It is only possible to close one port at any one time.

BLA Code 131138

Hose Width Depth Height Mount Size Handle Up Screws mm mm mm mm mm 38

139

110

157

5 r/h

section

Tsunami Bilge Pumps

Easy cartridge installation: just align cartridge tab with housing slot, twist to lock. Free flowing water around motor housing keeps motor cooled and extends life. Rugged, glass and mineral filled polymer body

Depress base tab to unlock filter from housing - ideal for manoeuvering in tight spaces and for cleaning filter. Double filter base resists clogging.

BLA Model Volt Open Flow Code @ 13.6V l/m gph 131554 T500 131556 T800 131558 T1200

12 12 12

31.5 500 50.5 800 76.0 1200

Output @1m gph

Hose Size mm

330 600 810

19 19 28

Max. Max. Amp Head Draw mm 2.1 3.3 2.7

1.3 2.4 2.7

Fuse

Height Diameter

amp

3 4 5

91 111 111

73 82 82

N.B. Output specifications are in US gallons per hour. While Attwood submersible bilge pumps have caulked wire, best practice installation is to ensure that wiring connections remain above water level.

Heavy Duty Bilge Pumps Designed for commercial/work boats where reliability and long life is paramount. The power head with integrated hose outlet locks to the base at 90ยบ increments for easy hose routing and installation. Permanent magnet motor with coil spring design, extra long composite brushes. Two independent impeller shaft seals keep the motor dry and act as a reservoir for shaft lubricant. Three year warranty for pleasure boats.

Welded housing seals out water.

Caulked and tinned wire prevents wicking and motor drowning.

High efficiency motor with permanent magnets, composite brushes and permanently lubricated bearings for long life.

Rugged, chemical resistant housing resists impacts and hull pounding. Parabolic chamber design moves water around housing to assist cooling the motor.

Easy to clean. Locking tab secures power head to base. Can be removed with one hand.

Impeller and parabolic chamber design prevent clogging from bilge debris

316 stainless steel shaft resists corrosion. Durable impeller constructed of high impact thermoplastic.

Large, durable filter strainer area. Debris passes through without clogging.

BLA Model Volt Open Flow Output Hose Code @ 13.6V @1m, 12V Size l/m gph gph mm 131576 HD1700 12 131578 HD2000 12

107 1700 126 2000

1000 1500

28 28

Max. Max. Amp Head Draw mm 3.3 4.9

6 8

PUMPS, PLUMBING & GALLEY

Available in three pump capacities, the Tsunami submersible bilge pumps are a unique design featuring a quick inspection twist lock cartridge design, allowing instant inspection of the impeller, or clearing of obstructions, without tools. Water circulates the motor housing to dissipate heat. Patented shaft seal centres directly on the motor shaft, preventing leaks caused by misalignment. Moulded two wire seal is permanently fused to the insulation and the tinned wire is caulked to prevent wicking and subsequent water entry to the motor housing. Three year warranty.

Fuse

Height Diameter

amp

10 12

165 170

135 135

www.bla.com.au

181

section

PUMPS, PLUMBING & GALLEY

Sahara Automatic Bilge Pumps An all in one automatic float switched bilge pump offering installation convenience as well as added security. Everything is contained in one compact package - pump, strainer and float switch. Installs quickly and easily in tight spaces.

Molded three wire seal is permanently fused to wire insulation to prevent leaks.

High efficiency, permanent magnet motor uses composite brushes and permanently lubricated bearings for longer life.

Wiring is tinned and caulked for corrosion resistance and to eliminate wicking.

The free flow of water around the motor housing keeps motor cool for extended life.

Test knob allows for easy and immediate operational check.

316 stainless steel motor shaft

Non restrictive float movement avoids binding in ‘on’ or ‘off’ position.

Patented reinforced motor shaft seal ensures perfect alignment of shaft and seal.

Larger filter area resists clogging. Pump/switch housing attaches to filter base with handy side lock snaps for quick, one hand removal for easy cleaning.

Durable high impact, glass filled polyester impeller

102

BLA Model Nominal Open Flow @ Code Voltage Design Voltage l/m gph 131580 S500 131582 S750 131584 S1100

12 12 12

Output Hose @ 1m, 12V Size gph mm

31.5 500 47.0 750 69.0 1100

300 480 820

19 19 28

Max. Amp Fuse Head Draw m amp 2.4 3.6 2.7

1.2 2.5 3.4

140

3 5 6

N.B. Output specifications are in US gallons per hour. While Attwood submersible bilge pumps have caulked electrical wire, best practice installation is to ensure that wiring connections remain above water level.

Supersub 500 Bilge Pump

Supersub Smart 650 Bilge Pump

The Whale Supersub 500 electric bilge pump has a super slim, low profile design and features an easy to clean integral strumbox.

The Whale Supersub Smart 650 automatic bilge pump is a super slim, low profile design making it ideal for areas where space is at a premium. An integral electric field sensor automatically switches on and off with the detection of fluctuating bilge water levels. Designed for quick and easy installation, the multi position pump head and outlet fits neatly into almost any area and position.

Features: • Extremely low profile, only 54mm high • Vertical or horizontal outlet position • Vertical or horizontal mounting • Removable strainer for easy cleaning • Strainer design leaves minimum water level

Features: • Unaffected by wave motion • Solid state switching with no moving parts • Environmentally friendly and mercury free • Integrated bleed ball prevents airlocks • Electric field sensor technology • Easy to clean built-in strum box, low maintenance design • CE certified and conforms to ISO8849 and ISO15083

54 187

BLA Open Code Flow I/m gph 131654 31.5 502

Outlet Power Mount Dia. Screws mm v amps gauge 19

12 2.6

4 r/h

N.B. As with all submersible electric’s, attention is needed during installation to ensure that wiring connections remain above water level. Specified output is US gph open flow.

182

Quality marine equipment

BLA Open Code Flow I/m gph 131656 36.6 600

Outlet Power Mount Dia. Screws mm v amps gauge 19

12 3.4

4 r/h

N.B. As with all submersible electric’s, attention is needed during installation to ensure that wiring connections remain above water level. Specified output is US gph open flow.

section

Heavy Duty Electric Submersible Bilge Pumps The highest quality submersible bilge pumps available from TMC. Aluminium motor enclosure base dissipates motor heat while the electrodeposition coating resists corrosion.

BLA Open Code Flow l/m gph 131600 131602 131603 131604 131606 131608 131613 131614 131616 131618

PUMPS, PLUMBING & GALLEY

Features: • Permanent magnet motor • Snap-on mount base strainer • Two year limited warranty • Every pump is water tested to ensure delivery head, voltage and amp draw are within specifications

Outlet Power Max. Base Height Dia. Head Dia. mm v amp m mm mm

31.5 500 63.0 1000 94.5 1500 126 2000 158 2500 190 3000 94.5 1500 126 2000 158 2500 190 3000

19 28 28 28 32 32 28 28 32 32

12 12 12 12 12 12 24 24 24 24

3.5 5.5 8.0 12 18 18 4.0 5.0 7.5 9.0

4.6 4.6 3.3 3.9 4.5 4.5 3.3 3.9 4.5 4.5

88 88 120 120 132 132 120 120 132 132

140 140 170 170 197 197 170 170 197 197

131540 Repair kit to suit 500 and 1000 models 131542 Repair kit to suit 1500 and 2000 models 131544 Repair kit to suit 2500 and 3000 models N.B. As with all submersible electric’s, attention is needed during installation to ensure that wiring connections remain above water level. Specified output is US gph open flow.

Compact Bilge Pump An economical submersible electric bilge pump available in 450 or 900gph. Compact low profile design for confined bilge areas. Snap-on mount base strainer. Every pump is in water tested to ensure delivery head volume and amp draw are within design specification before leaving the factory. 12 months warranty.

BLA Open Outlet Power Max Base Height Code Flow Dia. Head Dia. l/m gph mm v amp m

131590 28.3 450 19 12 1.5 2.0 131592 56.6 900 25 12 3.5 3.5

75 98

84 107

131592

N.B. As with all submersible electric’s, attention is needed during installation to ensure that wiring connections remain above water level. Specified output is US gph open flow.

Orca Electric Bilge Pumps

Strum Box

The Whale Orca electric bilge pumps are compact and powerful high performance pumps most suitable for recreational vessels. The housing is manufactured of robust fuel-resistant ABS plastic which is easily removed from the large filter base for easy cleaning and maintenance. ISO 8849 marine standard 3 year warranty.

An essential fitting for any manual bilge pump pick up hose to prevent debris entering and blocking the hose or jamming the pump. Multi directional port options facilitate optimal pick up position by utilising either top or side entry. Built-in non-return valve prevents backflow into the bilge and aids pump prime. Features: • Ideal for use with remote mounting pumps (e.g. Gulper 320) • Easy installation - multi directional port options for either top or side entry • Non-return valve prevents back flow into the bilge • Designed to fit deep down in the bilge • Compact design fits into tight spaces • Easy cleaning and maintenance

BLA Code

Open Outlet Power Height Width Depth Flow Dia. gph mm v amp mm mm mm

131410 131414 131418 131422

500 950 1300 1300

19 28.5 28.5 28.5

12 1.5 12 3.5 12 5 24 2.5

83 109 129 129

102 135 168 168

78.5 103 121 121

N.B. As with all submersible electric’s, attention is needed during installation to ensure that wiring connections remain above water level. Specified output is US gph open flow.

BLA Code

Hose Length Width Height Mount Size Screws mm mm mm mm mm

131120

19/38

150

4 r/h

www.bla.com.au

183

section

PUMPS, PLUMBING & GALLEY

Portable Hand Bilge Pump

Float Switch

A versatile hand held bilge pump for dinghy’s, small boats or as a backup pump. Rigid plastic and PVC, corrosion free construction.

Easily converts electric bilge pump to automatic operation by sensing rising water level. Can be used on any low voltage electric pump (6-32V) with a load current up to 15 amps. Can be installed horizontally or vertically. Environmentally friendly - no toxic mercury. Can be used as a high water alarm when mounted vertically. BLA Power Length Width Code Rating v amp mm mm 131688 6-32 15 110 59

BLA Barrel Outlet Code Length Hose mm mm 131060

600

106

4 r/h

N.B. As with all submersible electric’s, attention is needed during installation to ensure that wiring connections remain above water level.

32x600

Float Switch

Sure Bail Float Switch Super reliable float switch with cover, converts electric bilge pumps to automatic operation. High impact resistant polypropylene case protects the float mechanism from physical damage and fouling. Polyurethane foam filled float. Closed tube mercury switch. Pump cuts in at water depth of 45mm, cut out is at 20mm of water depth.

Economical, spark proof, plastic float switch. Running ball contact type with on/off switch, activated with rising water level. When water level lowers, the switch automatically turns the bilge pump off. BLA Power Length Width Code Rating v amp mm mm 131694 12-24 15

116

Height Mount On Screws mm gauge

5 r/h

N.B. As with all submersible electric’s, attention is needed during installation to ensure that wiring connections remain above water level.

BLA Power Length Width Height Mount Code Rating Screws v amp mm mm mm mm 131692 6-32 15 140 65 75 4 r/h N.B. As with all submersible electric’s, attention is needed during installation to ensure that wiring connections remain above water level.

Float Switch with Cover Converts bilge pumps into fully automatic pumping systems. Protected float switch with running ball actuated switch (not a Mercury switch) assures the reliability of these quality units. The float switch will actuate when the water level exceeds 50mm above the set point. Switch can be mounted onto the bottom of boats with deadrise of up to 24º, so virtually any bottom position will be suitable. There is a test knob for convenient testing of pump operation. Electrical wires do not move and subsequently deteriorate as the float moves, providing further reliability.

BLA Power Height Width Depth Mount Code Rating Holes mm mm mm mm 131696 12V-12A, 24V-6A

135

4 r/h

N.B. As with all submersible electric’s, attention is needed during installation to ensure that wiring connections remain above water level.

184

Height Mount On Screws mm mm

Quality marine equipment

Aerator Head For use with aerator pumps in livewells with built-in overflows. Black U.V. stabilised injection moulded plastic. Simple flow adjustment incorporated in the head. BLA Max. Wall Code Thickness mm 131722

O/all Hose Length Size mm mm

135

Mount Hole mm 27

Overflow Drain with Strainer These overflow drains for baitwells incorporate a strainer that stands off the flange 6mm to prevent live bait going out the overflow or clogging the drain. White U.V. stabilised injection moulded plastic with stainless steel screws.

BLA Mount Code 131779 131780

Straight 90º

Max.Hull O/all Thickness Length mm mm 28 28

101 105

Hose Size mm

Mount Hole mm

38 38

48 48

section

Anglers Aerator

Aerator system supplied complete with 28 l/m (450 US gph) submersible pump, three metres of electrical wire fitted with alligator clips, 1.5 metres of 19mm spiral hose, two suction cup spray rail mounting brackets, one 310mm long spray rail and one 130mm long spray rail. Recirculates water in livewells via spray rail to maintain oxygen level. Every pump is in water tested to ensure volume and amp draw are within specification.

Portable single piece live bait aerator to suit almost any application. Supplied with 1.2 metres of electrical wire fitted with alligator clips. 12 volt, 16 l/m (250 US gph) submersible pump fitted with three suction cup mounts and riser spray tube with 300 adjustable flow control. Every pump is in water tested to ensure volume and amp draw are within specification.

BLA Code

125

BLA Code

131712

131714

N.B. As with all submersible electric’s, attention is needed during installation to ensure that wiring connections remain above water level.

120

Bait Bubbler

Livewell Aerator Control

Self contained, portable aeration system. Operates from two 'D' cell batteries (not included) for approximately ten hours. Supplied complete with 800mm of tubing, weighted glass bead air stone and adjustable stainless steel mounting bracket. Ideal for beach anglers to keep bait live for hours in a bucket.

This unit features a solid state timer with adjustable cyclic run times. Run time is approximately 1.5 minutes, off time is variable from 1-10 minutes. Three way toggle switch; off/manual/auto. Suitable for all livewell pumps to ten amps. Black moulded plastic face with white raised lettering.

BLA Code 131718

Height Width mm mm 160

105

Depth mm

BLA Code

Face Size mm

131726

85x85

PUMPS, PLUMBING & GALLEY

Multi Purpose Aerator Kit

Cut Intrusion Mount Out Screws mm mm mm 60x52

4 c/s

Tsunami Aerator Pumps Based on the same technology platform as the Tsunami Bilge Pumps. These aerator pumps and associated installation accessories provide a reliable and versatile live tank pump solution. Water cooled motor housing dissipates heat for extended motor life. High efficiency permanent magnet motor with coil spring loaded, extra long composite brushes and permanently lubricated bearings for longevity. Wiring is tinned and caulked to prevent wicking water damage. Variable mount design and accessories enables easy installation as a recirculating system, with through transom or through hull installation. The mount configuration and high volume capacity of these pumps also sees them utilised on ski/wake boats to literally blast torrents of water ballast in or out, depending on the trim required. Pumps are not self priming and must be mounted below waterline.

BLA Pump Volt Open Flow Amp Fuse Code Model @ 13.6V Draw l/m gph amp 131699 T500 131700 T800

12 12

31.5 500 50.5 800

1.5 2.4

3 4

131719

131734

a & b Thread NPT

3/4" 3/4"

92 102

82 99

76 76

131707 Mount bracket for pump 131710 Livewell Pump System includes: pump (131699), bracket (131707) and spray head (131720) 131717 Straight tail 3/4" NPT to 19mm hose 131719 90º tail 3/4" NPT to 19mm hose 131720 Adjustable spray head to suit 19mm hose 131734 Moulded plastic intake strainer 3/4" NPT 131736 Stainless steel mesh intake strainer 3/4" NPT N.B. Output specifications are in US gallons per hour. While Attwood aerator pumps have caulked wire, best practice installation is to ensure that wiring connections remain above water level.

131720

131717

131707 131736 a e

c b

www.bla.com.au

185

section

PUMPS, PLUMBING & GALLEY

Diverter Valve Control

Aerator Rail

This diverter valve provides an alternative to hand operated 'Y' valves. One pump can supply two different functions such as bait tank and wash down via the recessed rotary remote control lever. Totally rust free construction.

Combination adjustable flow control ball valve and spray rail in one. Non-corrosive black thermo plastic construction makes it suitable for salt and freshwater. Overhead or side mounting.

BLA Code

BLA Hose Cable Control Code Size Length Dia. mm in m mm 131822 19

3/4

2.6

131730

Hose Length Height Depth Size mm mm mm mm 19

265

Mount Screws mm

5 r/h

Bait Tank Aerator Kit

Livewell/Bait Tank Pickup Installed through the transom for connection to self priming livewell pumps. The cast 316 stainless steel head fitting is installed above waterline and can be fitted with a 3/4" ball valve for added security. The 16mm stainless steel pick up tube fits into the head assembly via a rubber cup gasket allowing easy removal for clearing of debris. The pick up tube can be cut to length if required and is supplied standard with an angled tip to provide water flow when under way, without pump. The lower mount saddle has a rubber insert that allows connection at any height and also secures the pickup tube into the head assembly.

3/4" BSP to accept valve

Gasketed removable stainless steel tube

The Pro Air system contains the plumbing hardware required for connection to a water pump to make a livewell system. Water plumbing includes 'T' joiner, 90º flow direction head and spray head with flow valve, all to suit 19mm hose. Also included is a tank drain skin fitting (28mm hose size) that accepts a 90º overflow pipe. Simply remove the overflow pipe to drain the livewell tank.

Pull out to drain tank

BLA Code 131796

Saddle can be installed at any height

Livewell Overflow Drain BLA Code

Thru Hull BSP

Max. Hull Thickness mm

Pick Up Tube mm

Mount Screws mm

131966

3/4"

16x300

4 c/s

Overflow Fittings with Filters Designed principally for livewells and bait tanks, these straight or 90º elbow filtered drains allow maximum overflow, yet retain the bait or fish. Twist off cap for easy removal and cleaning.

90º injection moulded drain fitting installs in base of live tank, for connection to through hull, with minimal space requirement under live tank. The plastic and PVC overflow tube is fitted into drain fitting to keep livewell water depth at desired level. Grate at top of overflow tube prevents catch or live bait from blocking overflow tube. To empty live tank remove the overflow tube. Over flow tube is 450mm long but can be cut down as required. Tube and drain purchased separately.

131968

BLA Description Code 131972 Straight outlet 131974 90º elbow outlet

186

Hose Flange Cut Out Intrusion mm mm mm mm 38 38

Quality marine equipment

74 74

48 48

84 98

BLA Outlet Hose Code Size mm 131968 90º

131970 Overflow tube

Flange OD mm

Cut Out Dia. mm

Intrusion

100

section

Grey Waste Tank

PUMPS, PLUMBING & GALLEY

Where shower drains or galley sinks are near or below the waterline, preventing drainage by gravity, the Whale Grey Waste tank provides a low position sump for collection of water with single outlet to pump overboard or to holding tank. Fitment of the Gulper 320 pump can be direct to well nuts moulded in side of tank, or installed remotely depending on requirements. New simplified wiring includes an electronic field sensor switch with no moving parts to activate the remote pump. Multi dimensional inlet ports enable a variety of hose sizes to be connected from showers, sinks, ice makers, air conditioners, etc. Easy quick access for cleaning. Features: Inlets: 2 x 19mm, 3 x 25mm, 3 x 38mm Outlets: 1 x 19mm, 1 x 25mm

Typical Remote Pump Installation Power Supply

To Discharge

Shower tray

Override switch

Sink Grey Waste Tank

Gulper 320 Pump

BLA Volt Code 132003 12-24

Max. Outlet Pump Dia. amp mm 30

19/25

Capacity Length

Width

Height

litres

8.15

255

230

170

131990 Replacement clear lid 131991 Replacement float switch

Grey Waste System with Pump Fully self contained sump with multiple inlets, submersible pump and automatic switch to pump grey waste overboard, or to holding tank, via a single outlet hose. At the heart of the system is a Sahara 750 automatic bilge pump. Snap on/off gasket sealed clear lid provides immediate visibility of filter build up and allows easy access for cleaning. Outlet hose connections and anti airlock vent connections are open, the three multi size inlet connections are closed ready to be drilled or cut open as required. Additional inlets can be accommodated by installing skin fittings to the sump box sides.

10ø to vent 19ø to outlet

206

4mm r/h

BLA Volt Amp Output Code Draw @ l/m head l/m gph 131996 12 131998 24

2.5 1.4

26.5 26.5

420 420

Fuse amp 4 2

350 Inlets: 19 & 25ø 19ø

114

28 & 38ø

N.B. Output specifications are in US gallons per hour nominal voltage

www.bla.com.au

187

section

PUMPS, PLUMBING & GALLEY

Bronze Impeller Pump

Manual Vertical Galley Pumps

Durable bronze housed rubber impeller pump for general purpose salt water and fresh water applications, but not drinking water. Flexible rubber mounts absorb running sound and reduce vibration transmission. Inlet and outlet ports are both threaded 1/2" BSP inside and 3/4" BSP outside. Self priming but do not run dry.

Simple but reliable self priming double action vertical pump mechanism. Suitable for salt and fresh water. Easy single 32mm hole installation. Available in alloy pump barrel. Gloss finish injection moulded head assembly with anodised alloy spout. Seals carry FDA food grade certification. Applications include boat galleys and heads, caravans, camper’s, relocatables and portable toilet sinks, etc. 5 litre per minute capacity.

Specifications: • 25 l/m open flow • Lift 1.5 metres • Head 4 metres

BLA Head Barrel Protrusion Intrusion Hose Code Colour Size mm mm mm 133038 Black 133040 White

Alloy Alloy

95 95

180 180

13 13

Manual Sump Pump

BLA Power Length Width Height Code v amp mm mm mm 132196 12 8 170 130 139242 Replacement impeller

Mount Screws mm

Designed for the removal of sump oil through the dipstick hole. Brass and neoprene construction. Complete with pickup and outlet tubes.

5 r/h

Electric Impeller Pump Economical rubber impeller pump with plastic pump body for general purpose salt water and fresh water applications, but not drinking water. Supplied with in-line fuse holder. Rubber grommets inserted in the mount holes for isolation of motor vibration. Self priming but do not run dry. Specifications: • 25 l/m open flow • Lift 1.5 metres • Head 4 metres • Inlet/outlet 25mm

BLA Intake Tubes Code mm

Outlet Pump Pump Tube Length Dia. mm mm mm

132100 8x600 & 6x600 12x240

Galley Foot Pump

230

- Double Action

Universal mounting via floor or bulkhead fastenings, with rotatable inlet/outlet connections. Mounts inside galley cupboard with pedal access through bulkhead. Injection moulded plastic housing with diecast alloy pedal, neoprene diaphragm and valves. Applications include boats, caravans, campers, portable toilet sinks, etc.

BLA Power Length Width Height Code v amp mm mm mm 132202 12 8 170 132204 24 4 170 139242 Replacement impeller

188

Quality marine equipment

130 130

98 98

Mount Screws mm 5 r/h 5 r/h

BLA Capacity Hose Width Height Front Code Size to Back l/m mm in mm mm mm 133002 15 13 1/2 133402 Diaphragm/valve kit

152

123

205

section

Flipper Mk4 Galley Pump

This simple, adjustable height, vertical hand pump is self-priming and is ideal for installations where space is limited. The narrow mounting base allows neat fitting between two sinks to serve both. Fits directly into Whale System 15 plumbing. Constructed from acetal copolymer, anodised aluminium, neoprene, nitrile rubber and stainless steel.

A self-priming rocker action, hand galley pump that is simple to install and service. Swivelling faucet, single action output with fine flow control. Constructed from acetal copolymer, nylon, polystyrene, anodised aluminium, neoprene, nitrile rubber and stainless steel. Max. Lift m

133054 7 3 133430 Service kit BLA Cap Code l/m

Max. Lift m

Hose Size mm

Mount Base mm

Above Bench mm

Mount Screws mm

133050 8.2

32x80

90-390

4 c/s

133420 Service kit

Baby Foot Mk2 Manual Galley Pump Designed for simple and space saving floor mounting, the Baby Foot pump is a single action pump that incorporates efficient flap valves, providing maintenance of prime. Can also be used as a primer and standby pump with a Whale electric centrifugal pump in a combined electric/manual system. Constructed from moulded acetal copolymer, nylon, stainless steel and neoprene rubber. Self-priming.

Hose Size mm 13

The Gusher Galley Mk3 has been fitted by thousands of satisfied users worldwide and is probably the most popular marine foot pump ever made. Easy, smooth double action gives fine control from a trickle to full flow. Three mounting arrangements: on floor, behind bulkhead or on a bulkhead. Very neat when installed with pedal through bulkhead. Ideal as a backup pump for an electric water system and fits directly into Whale System 15 plumbing. Multi directional inlet and outlet hose connections. Suitable for salt and freshwater. Constructed from acetal copolymer, nylon, neoprene, nitrile rubber and stainless steel.

BLA Capacity Max. Hose Width Height Front Mount Code Lift Size to Back Screws l/m m mm mm mm mm mm 133062 15 2 133446 Service kit

133058 8 1.5 133440 Service kit

Mini Submersible Electric Pump

137

100

Gusher Galley Mk3 Pump

BLA Cap. Max. Hose Depth Width Height Mount Code Lift Size Screws l/m m mm mm mm mm mm 13

104

181

BLA Cap Code l/m

113

122

Features: • Adjustable height • Suitable for fresh and salt water • Smooth double action

PUMPS, PLUMBING & GALLEY

'V' Pump Mk6 Manual Galley Pump

152

131

196

4 r/h

4 r/h Handy, small diameter submersible pump for use in confined spaces such as lowering into 20 litre containers. Each pump is in water tested for delivery head, volume and amp draw before leaving the factory.

Tiptoe Mk4 Manual Galley Pump Designed for neat, through floor mount. When not in use, the plunger locks down flush with the floor. A simple twist with the foot releases the plunger for use. Smooth, double action flow on each stroke. A return spring assists pumping. Suitable for salt and freshwater, fits directly into Whale System 15 plumbing. Constructed from acetal copolymer, nylon, neoprene and nitrile rubber and stainless steel.

BLA Open Flow Code Output l/m

Outlet Power Max. Height Base Dia. Head Dia. mm v amp m mm mm

131698

9 & 11 12 2.5

4.5

110

N.B. As with all submersible electric’s, attention is needed during installation to ensure that wiring connections remain above water lever.

BLA Cap. Max. Hose Intrusion O/all Cut Out Mount Code Lift Size Dia. Dia. Screws l/m m mm mm mm mm mm 133066 7 2 133450 Service kit

160

115

5 c/s

Whale Superseded Galley Pump Spares 133420 Galley ‘V’ pump MK 5 service kit 133430 Galley Flipper MK 3 service kit 133444 Gusher Galley MK 2 service kit

www.bla.com.au

189

section

PUMPS, PLUMBING & GALLEY

Premium Submersible Pump

High Flow Submersible Pump

A compact, highly efficient centrifugal pump with high performance. Designed to be dropped into a water tank or container, this submersible pump has a built-in strainer to prevent suspended particles from entering the system. Suitable for fresh water, saltwater and diesel transfer. Constructed from ABS plastic, stainless steel and nitrile rubber. Suitable for use with 3/8" or 1/2" I.D. hose. For connection to system 15 use adaptor 136638. One year warranty.

High flow submersible centrifugal electric pump. This pump features a self bleed valve that allows any air trapped in the pump to escape for greater pumping efficiency. A built in strainer incorporated in the base prevents suspended particles from entering the system. Suitable for fresh water, saltwater and diesel transfer. Constructed from ABS plastic, stainless steel and nitrile rubber. For connection to system 15 use adaptor 136638. 12 volt, 3.8 amp with 15.8 l/m capacity at open flow. One year warranty.

BLA Cap. Power Length Code Open Flow l/m v amp mm 133102 133103

13.2 13.2

12 3.6 117 24 1.8 117

O/all Dia. mm

BLA Hose Length Code Size mm in mm 133104 10 3/8 13 1/2

36 36

160

N.B. Ensure that wiring connections remain above water level.

Mini Electric Galley Pump

In-line Electric Pumps

12 volt centrifugal pump with mount bracket. The pump comes complete with compact chrome plated swivel faucet with integral switch. Faucet dimensions are, base 90 x 43mm, height 117mm.

Designed for confined spaces, these pumps can be fitted below a water tank and gravity-primed, or above the water tank with a manual priming pump. Can be fitted in-line with a submersible pump to boost the performance when higher pressure for a shower/water heater is needed. Constructed from ABS plastic, stainless steel and nitrile rubber. Suitable for fresh water or saltwater. For connection to system 15 adaptor use 136638. One year warranty.

BLA Power Capacity Head Pump Width Pump Length Code v amp l/m m mm mm 133120 12 3

6.6

120

Portable Pump Kit Versatile 12 volt submersible pump with hose and nozzle. Suitable for cold and warm water, diesel, light oils, detergents and most pesticides. Not suited to petrol, highly flammable or corrosive liquids. Kit inclusions: • Supersub centrifugal pump with 3.5 metre lead fitted with two alligator clips and cigarette lighter style plug • Nozzle - adjustable on/off, fine spray or a jet of water • 3.75 metre food quality clear hose

190

O/all Dia. mm

BLA Cap. Power Hose Length O/all Code Open Flow Size Dia. l/m v amp mm in mm mm 133106 13.2 12 3.6 133108 15.75 12 3.8

133114

133118 12 1.5

Quality marine equipment

144

1/2

Submersible in-line pump supplied with 3.1 metres of electrical cord fitted with a cigarette lighter plug, waterproof in-line on/off switch, two metres of 10mm ID hose and adjustable flow shower head with suction cup mount. Ideal for camping and boating.

BLA Power Code v amp

12 6.5

3/8 1/2 3/8

Portable Shower Kit

BLA Capacity Power Code l/m v amp 13.4

10 13 10 13

section

Pressure Switch MK2

Trigger action compact deck wash hose nozzle. Adjustable spray jet and flow control. Available as a complete unit with quick connect fitting to suit 13mm (1/2") hose, or components can be purchased separately.

Recommended for use with the Whale in-line submersible and non-automatic pumps installed in conjunction with Whale Elegance faucets. The pressure switch detects pressure drop with the opening of any tap in the system and activates the pump instantly. Adjustable pressure setting to a maximum of 2.6 BAR (30 PSI). Requires 2 x 136639 adapters to enable use with 1/2" hose or Quick Connect 15 pipework.

133200

133204

133202

BLA Power Code v amp 133471 12 10 24 5

BLA Code

Description

133201

Deck wash nozzle complete

133200 Replacement nozzle 133202 Hose connector 133204 Nozzle adaptor to suit connector

Aquasource Clear Disposable Filter Aquasource Clear gives a refreshing taste to the water you drink by removing unpleasant smells and particles while inhibiting the growth of bacteria. It can help prevent stomach bugs often caused by poor quality water. Its longer length (30cm) means that water is better filtered through longer contact with the silver activated carbon. Its slim and compact size enables it to be located in confined spaces. Supplied with 12mm nipples and mount bracket. To fit Whale semi-rigid pipework Quick Connect 15, use adaptor 136639. Whale has designed the filter to last one season or 4500 litres and recommends that the filter be replaced after this period. Maximum pressure 4 bar.

300

Height

102

Surge Damper Prevents water hammer and also reduces switch hunting. Designed for pressurised water systems using Whale system 15. The surge damper should be mounted in a vertical position immediately after the pump discharge side. Connection is via a 12mm nipple. For connection to Whale Quick Connect 15 pipework, use 136639, a 136624 â&#x20AC;&#x2DC;Tâ&#x20AC;&#x2122; piece will also be required. Completely sealed unit requiring no servicing. Supplied with mount bracket.

BLA Code 133820

O/all Diameter Mount Height Screws mm mm mm 210

4 c/s

Coiled Deck Wash Hose This coiled deck wash hose is the neat solution to deck clutter and elimination of kinked hoses. The 7.6 metre coiled hose stows neatly in its plastic pod and is supplied with a spray nozzle and fitting accessories for connection of water supply.

BLA Diameter Length Mount Code Screws mm mm mm 133804

Length Width

PUMPS, PLUMBING & GALLEY

Deck Wash Nozzle

4 c/s

Non-Return Valve Incorporates a specially moulded base to prevent it being sucked flat to the base of a water tank when used in the end of a supply hose. Ensures maintenance of prime. White plastic body. Constructed from acetal and nitrile rubber.

BLA Hose Code mm in 133850 13 1/2

Length Diameter mm mm 47

BLA Code

Depth mm

133150

115

Width Height mm mm 475

255

www.bla.com.au

191

section

The Elegance Range

PUMPS, PLUMBING & GALLEY

Suitable for pressure or micro switched systems. Use 136639 adaptor for connection to Whale System 15 pipework. Features: • Microswitch (supplied) is easily installed without tools. Turns on and off non pressure pumps with turn of tap • Pillar valve for fine flow control • Internal joints and seals are not under pressure when taps are closed • Available as single or mixer units • Robust ABS construction • Elegance faucets and showers are serviceable, they are not sealed units

Combination Faucet Shower

Swim-N-Rinse

The swivelling faucet features a socket base unit with a retractable hose that enables use as a faucet or shower. Water flow can be temporarily shut off at the shower head. Wall mount for shower head included. Available as single or mixer tap.

Ideal for the swim platform of any boat. This recess mounted unit features a retracting hose and multi adjustable shower head. Available as a single or mixer tap with or without hinged cover.

134106 Single 134108 Mixer

112x53 164x55

12 12

120 120

4 c/s 4 c/s

110 88

298

N.B. Space must be available beneath tap for shower hose storage.

134602 134603 134607 134609 136639

Tap service kit Tap knob, stem, red and blue rings Replacement hose, 1/2" and 3/8" BSP metal ends, 1.7m Replacementhandset - 1/2" BSP Adaptor to connect to system 15

Superseded Parts: 134604 Replacement hose, 3/8" BSP plastic ends, 1.7m 134606 Replacement handset - 3/8" BSP BLA Description Cover Mount Code

Single Faucet Tap Swivelling standard faucet for cold water only systems.

BLA Code

Mount Base mm

134110 134111 134112 134113

Hose Height Mount Size Above Bench Screws mm mm mm

1/2" 1/2" 1/2" 1/2"

Screws mm

ext. ext. ext. ext.

6 6 6 6

c/s c/s c/s c/s

Tap Controls

Swivelling mixer faucet for hot and cold water systems. Available in short or long faucet configuration.

Remote tap fittings for operation of 134115 (next page) or any stand alone water outlet. Matches all other Elegance taps. 1/2" BSP tap inlet.

Hose Height Mount Size Above Bench Screws mm mm mm

134102 Mixer short 164x55 12 12 134104 Mixer long 164x55 134602 Tap service kit 134603 Tap knob, stem, red and blue rings 136639 Adaptor to connect to system 15

Quality marine equipment

No Yes No Yes

Tail BSP

N.B. Space must be available behind unit for hose storage.

Mixer Faucet Tap

BLA Description Mount Code Base mm

Single swim/rinse Single swim/rinse Mixer swim/rinse Mixer swim/rinse

Tap

134602 Tap service kit 134603 Tap knob, stem, red and blue rings 134608 Replacement hose - 1/2" and 3/8" BSP metal ends, 2.1m 134609 Replacement handset 1/2" BSP Superseded Parts: 134605 Replacement hose, 3/8" BSP plastic ends, 2.1m 134606 Replacement handset - 3/8" BSP

134100 112x53 12 120 4 c/s 134602 Tap service kit 134603 Tap knob, stem, red and blue rings 136639 Adaptor to connect to system 15

192

180

BLA Description Mount Hose Height Mount Code Base Size Above Bench Screws mm mm mm mm

120 184

4 c/s 4 c/s

BLA Tap Code

Mount Outlet Base mm

Height Mount Above Bench Screws mm mm

61x55 3/8" BSP ext. 134125 Cold 134127 Mixer 113x55 12mm 134602 Tap service kit 134603 Tap knob, stem, red and blue rings

38 38

4 c/s 4 r/h

section

Whale Twist Hand Showers A truly innovative and versatile deck shower combining real shower feel with performance and functionality. Fast, simple installation requiring only one circular hole and easy plumbing connection. The design incorporates integral twist control allowing simple flow adjustment.

BLA Description Code

Outside Cut Out Max. Plumbing Dia. Size Intrusion Connection mm mm mm BSP

134160 Cold only handset with angled housing 134162 Mixer handset with straight housing 134164 Mixer handset with angled housing

Compact Shower

119 53 119

88 48 88

330 330 330

1/2" int 1/2" ext 1/2" ext

- PVC Cover

Featuring a white U.V. stablised polypropylene body and a PVC cover, this compact shower is suitable for mounting in vertical surfaces. Features: • Neat compact housing • Splash proof U.V. stabilised cover • On/off control in shower head • Use with remote mixer taps on previous page • 2.1 metre reinforced retracting hose • 3/8" BSP external thread hose connection

182

PUMPS, PLUMBING & GALLEY

Features: • Lightweight rubber Deck Protect™ end cap design prevents damage to gelcoat and deck • Wipe clean nozzles for easy removal of lime scale • Twist control adjusts temperature if connected to hot water supply • High quality ceramic valves for maximum efficiency and accurate control • Streamlined ergonomic design • Manufactured from high quality U.V. resistant ASA materials • Unique unobtrusive housing available in two holder styles (mixer only) • Can be conveniently mounted on flat or curved surfaces • 2.5m patented single D hose carries hot and cold water (mixer only) • Rubberised end cap makes handset easy to pull out for use and acts as a seal when stowed, no need for cover or lid

BLA Intrusion Cut Out Code mm mm 134115 150 80 134608 Replacement hose, 1/2" and 3/8" BSP metal ends, 2.1m 134609 Replacementhandset - 1/2" BSP

Compact Shower and Mixer

- Stainless Cover

Matching hand held shower and mixer top set with spring loaded, stainless stel hinged cover that stays open when in use and snaps shut for a sleek, neat appearance when not in use. Shower hand sets are supplied with 2.1 metres of hose attached, trigger control on/off chromed brass head, chromed plastic hand grip and are available in vertical or horizontal mounting configurations. Shower mixer taps are mains pressure rated and have a 3/8" BSP internal threaded plumbing connection. All models feature a white plastic recessed housing. 134317

134319

BLA Code

Description

134317 134318 134319

Vertical handset Horizontal handset Mixer tap

www.bla.com.au

193

section

Capri Tapware Range

PUMPS, PLUMBING & GALLEY

Contoured hollow grip handle and a slim profile make the Capri range the ideal choice for compact areas. Features: • Single lever flick mixer control • Maintenance free ceramic disc valves • Bright chrome finish • Connector hoses and under bench mount hardware included

134238

134240 has a pull out handset/shower with trigger on/off control. The water can also be adjusted from stream to spray by moving the rose surround in or out.

134240

134239 c

BLA Type a b c d Plumbing Code Connection mm mm mm mm BSP 134238 Short swivel faucet 134239 Long swivel faucet 134240 Combo tap/shower

45 45 45

140 175 150

140 140 140

250 250 250

1/2" 1/2" 1/2"

ext ext ext

N.B. 134240 also requires space below for shower hose storage.

Pacific Tapware Range Clean contoured oval design to complement the aesthetics of contemporary interiors. Features: • Single lever flick mixer control • Maintenance free ceramic disc valves • All bright chrome finish • Fixed and swivelling faucets include stainless steel braided connector hoses and under bench mount hardware • 134254 has a pull out handset/shower with press button control of water stream (flow or shower spray)

134248 134258

A range of shower hardware to match with Pacific tapware is available and detailed on page 196. 134250

134252

134254

BLA Type a b c d Plumbing Code Connection mm mm mm mm BSP 134248 134250 134252 134254 134258

Fixed faucet Short swivel faucet Long swivel faucet Combo tap/shower Shower mixer

48 52 52 52 70

95 140 200 190 80

140 150 150 170 100

N.B. 134254 also requires space below for shower hose storage.

194

Quality marine equipment

340 340 340 340 –

1/2" int 1/2" int 1/2" int 1/2" int 1/2" ext

a d

b d

section

Coral Tapware Range A unique look and feel for the discerning boat owner.

134260 134262

A range of shower hardware to match with Coral tapware is available and detailed on page 196.

134264 a

134266

134270

BLA Type a b c d Plumbing Code Connection mm mm mm mm BSP 134260 134262 134264 134266 134270

Fixed faucet Short swivel faucet Long swivel faucet Combo tap/shower Shower mixer

48 52 52 52 70

95 140 200 190 80

140 150 150 170 100

1/2"

340 340 340 340 –

int int 1/2" int 1/2" int 1/2" ext 1/2"

N.B. 134266 also requires space below for shower hose storage.

Adriatic Tapware Range Minimalist euro styling for those who prefer simple form. Features: • Single lever flick mixer control • Maintenance free ceramic disc valves • All bright chrome finish • Fixed and swivelling faucets include stainless steel braided connector hoses and under bench mount hardware • 134282 has a pull out handset/shower with press button control of water stream (flow or shower spray)

134274

134276

PUMPS, PLUMBING & GALLEY

Features: • Single lever flick mixer control • Maintenance free ceramic disc valves • All bright chrome finish • Fixed and swivelling faucets include stainless steel braided connector hoses and under bench mount hardware • 134266 has a pull out handset/shower with press button control of water stream (flow or shower spray)

A range of shower hardware to match with Adriatic tapware is available and detailed on page 196. 134282 134280

134278 134286

BLA Type a b c d Plumbing Code Connection mm mm mm mm BSP 134274 134276 134278 134280 134282 134286

Short fixed faucet Tall fixed faucet Short swivel faucet Long swivel faucet Combo tap/shower Shower mixer

53 53 52 52 52 70

85 85 140 200 190 80

210 340 150 150 170 100

340 340 340 340 340 –

1/2"

int 1/2" int 1/2" int 1/2" int 1/2" ext 1/2" ext

a d

N.B. 134282 also requires space below for shower hose storage.

www.bla.com.au

195

section

Shower Accessories

PUMPS, PLUMBING & GALLEY

This range of shower fittings is fully interchangeable allowing mix and match to suit decor and installation requirements. The range is compatible with Pacific, Coral, Adriatic and Mini Shower taps.

Hand Shower

Shower Handset

Installed in conjunction with shower mixer taps. White reinforced hose. Compact white handset with integral on/off button and adjustable flow control (stream/spray). Chrome finish ABS plastic wall mount bracket included.

White moulded ABS plastic shower head with chrome trim. Push button on/off thumb control. Chrome trim ring slides in and out to control flow (stream or spray). Accepts 134326 and 134328 hoses.

BLA Length Code m

Thread

134314

1/2"

2.0

BSP int

Hand Shower Wall Brackets

Shower Handset Shower Handset White moulded ABS plastic shower head with chrome trim.

Chrome finish ABS plastic wall brackets that provide angled wall mounting for shower hand sets. All brackets accept the 134326 and 134328 shower hose end fitting and also accept the shower 134344 hand set of 134240.

Lever action on/off/flow thumb control. Chrome trim ring slides Chrome finish ABS in and out to control flow (stream or spray). Accepts 134326 plastic shower rose. and 134328 hoses. Easy clean flexible PVC jets. Accepts 134326 BLA Length Width Height Thread 134328mm hoses. mm Code and mm BSP

134346

134324

134342

130

1/2"

ext

Hand Shower Wall Brackets Chrome finish ABS plastic wall brackets that provide angled wall mounting for shower hand sets. All brackets accept the 134326 and 134328 shower hose end fitting and also accept the shower hand set of 134240. BLA Protrusion Height Code mm mm 134342 134344 134346

95 40 82

Width

Chrome finish ABS plastic shower rose. Easy clean flexible PVC jets. Accepts 134326 and 134328 hoses.

75 44 49

Shower Handset

62 44 70

BLA Capacity Length Width Height Thread Code l/m mm mm mm BSP 134325

200

1/2"

Shower Hoses Available in white finish reinforced PVC or chrome finish spiral reinforced PVC hose. Swaged chrome and stainless steel end fittings. Fits all wall brackets above and all handsets above.

BLA Hose Code Colour 134326 Chrome 134328 White

Length Thread 134326

BSP 1/2" 1/2"

1.5 1.5

int int

Cold Water Stowaway Shower Cold water tap set in flush mount, U.V. resistant, white ABS plastic housing. Incorporates shower head on a 1.8m long hose. Has a built in 12/24 volt switch for pump control. Pull switch to activate pump, connection closing the door, automatically switches pump off. 1/2" BSP external thread plumbing connection.

BLA Code

Cut Out O/all Size Width mm mm

134352 180x152

O/all Height mm

O/all Depth mm

185

209

N.B. Space must be available underneath panel for showerhead and hose storage.

196

Quality marine equipment

134328

ext

section

Mini Taps - Chrome Plated Brass

PUMPS, PLUMBING & GALLEY

Italian made chrome plated brass mini single tap, double tap and double shower mixer unit Taps have chrome ABS handles with red and blue indicators. Suitable for bench or wall mounting.

134306

134304 134302

BLA Style Code 134302 134304 134306

Tap Tail BSP 3/8"

& 1/2" & 1/2" 3/8" & 1/2"

Mixer faucet Single faucet Shower mixer

3/8"

a b c mm mm mm 135 95 135

65 240 65 225 65 –

Bermuda Mixer Tap Timeless styling in a twin control but compact form. Features: • Tall swing away mixer faucet with soft flow head • Individual hot and cold control • Solid chrome brass construction • Simple one hole installation • All bright chrome finish • Stainless steel braided connector hoses and under bench mount hardware included

BLA a b c d Plumbing Code Connection mm mm mm mm BSP 134290 46

115 210

340

1/2"

a d

INT

Telescopic Faucets

Tuckaway and Telescopic Faucets

For use with foot operated galley pumps and non-pressurised electric galley pumps. Twist on/off valve. 20mm mount hole. Suits 10 and 13mm hose.

Simple and lightweight Whale faucets. Easy to install and available with an optional on/off valve. For use with Whale foot or non-pressurised electric pumps. Moulded acetal and anodised aluminium construction. Suits 10 and 13mm hose.

BLA Style Code BLA Code 134018

134004 Tuckaway 134006 Telescopic 134008 Telescopic

On/off Valve

Colour

Yes No Yes

White White White

134004

134006

www.bla.com.au

197

section

PUMPS, PLUMBING & GALLEY

Isotemp Stainless Steel Water Heaters

Smart finish in a brushed stainless steel exterior, the quality of the Isotemp Basic by Isotherm, is not just skin deep. Optimal water heating is achieved in two ways, firstly by an immersed electric heating element (immersion heater) and secondly by utilising the boat's engine water heat (Heat Exchange). Isotemp water heaters may be used with fresh water or salt water cooled engine systems. The immersion heater and heat exchanger are positioned in the lowest part of the tank, providing even thermo cycle heating of the water in the system. The engine water heat exchanger coil is extra long for faster heating, especially handy on sailing yachts which may run their engine for short periods only. The water inlets and outlets are positioned to minimise mixing of cold water into the hot, by the incoming water. The immersion heater has been designed to enable easy removal to allow for inspection and cleaning of the tank. The materials used in the construction of the tank are of the highest quality. Acid resistant stainless steel AISI 316 is used for all parts of the tank that are in contact with water. The internal tank is insulated with expanded polyurethane insulation ensuring low temperature loss. The outer cover and mounting feet have been crafted from non-magnetic stainless steel AISI 304. The fixing feet are adjustable to 360Âş, allowing the tank to be mounted horizontally or vertically. An optional accessory to the range is the thermostatic mixing valve, 135840, (controls the maximum temperature of water at the tap) which adds to safety, particularly importantÂif having young children on board. The Isotemp range of water heaters by Isotherm have a two year full warranty and a five year limited warranty on the tank.

BLA Volume Style Code litres 135692 135696 135700 135702 135704 135706

20 25 24 40 50 75

Slim Slim Basic Basic Basic Basic

Dimensions Weight Length x Dia. mm kg 655 x 295 780 x 295 460 x 395 630 x 395 750 x 395 1040 x 395

9 11 11 17 20 24

Max. Immersion Pressure Heater bar volt watt 5.0 5.0 5.0 5.0 5.0 5.0

240 240 240 240 240 240

750 750 750 750 750 750

Thermostatic Mixing Valve

Immersion Heater Element

A highly recommended option for all water heaters. Controls the maximum temperature of water at the tap or shower. Supplied complete with all components required to install to any Isotemp Basic or Slim water heaters.

Isotherm stainless steel water heaters are supplied standard with 240 volt, 750 watt immersion heating elements. For vessels travelling to or being exported to USA, the 240 volt element can be replaced with a 110 volt 750 watt element. Element to be fitted by a licensed electrician or registered electrical contractor.

BLA Code 135840

Pressure Relief Valve Replacement hot water pressure relief valve to suit Isotemp water heaters. Threaded 1/2" BSP and preset to 500 kPa. Requires 135730 and a 135734 if retro fitting to existing systems.

BLA Code 135728 135730 15mm Brass 'T' 135734 Brass Nipple

198

- Australian Standards Approved

Quality marine equipment

BLA Description Code

Volt

Watt

135720 Replacement element 240 135722 Replacement element 115

750 750

Water Heater Hose Tail Kit Set of four brass tails to provide connection of hoses from both engine cooling system and fresh water supply to Isotemp Slim and Basic water heaters. All four tails are internally threaded 1/2" BSP. The engine connection tails accept 16mm hose and the fresh water connections accept 13mm hose. BLA Code 135640

section

Double Bowl Sink

Top quality, polished 304 grade stainless steel sinks with flange. hole to suit 25mm waste fittings. Supplied complete with plug and plastic waste.

Top quality, polished 304 stainless steel sink with flange. Holes to suit 25mm waste fittings. Supplied complete with two plugs and plastic wastes.

BLA Code 135002 135006

Length Int. mm 280 350

Width Depth Flange Int. mm mm mm 225 300

125 160

BLA Code

10 15

135018

Square Sink Top quality polished 304 grade stainless steel sink with flange. hole to suit 25mm waste fittings. Supplied complete with plug and plastic waste.

BLA Code 135020

Length Int. mm

Width Int. mm

Depth

Flange

305

165

BLA Code 135026 135028

305

165

Diameter Int. mm

Depth

Flange

280 335

110 110

15 20

Countersunk flush drains. Suit sinks listed on this page or can be used for ice boxes, livewells, roof drains, etc. Moulded in white nylon. Plug sold separately. BLA O.D. Code mm

Mount Intrusion Hose Holes Size mm mm mm in

135210 44 34 135212 45 33 135202 25mm rubber plug

Length O/all mm

Width O/all mm

330

260

Depth Flange mm

125

19 3/4 25 1

Moulded white nylon. Unique design provides 90ยบ elbow or straight mounting. The countersunk inner sink fitting is in itself a tail, simply cut down the outer elbow section for straight installation. Fits all sinks listed on this page or it can be used for iceboxes, livewells etc. Plug sold separately.

Mount Intrusion Hose Hole Size mm mm mm in

135211 46 34 135202 25mm rubber plug

50 41

Flush Drain/Sink Waste

Countersunk flush drain, 90ยบ elbow configuration moulded from white nylon. Suits all sinks listed on this page or can also be used for ice boxes, livewells, etc. Plug sold separately. Outside Dia. mm

305

Flush Drains/Sink Wastes

Flush Drain/Sink Waste

BLA Code

670

Flange

Top quality polished 304 grade stainless steel sinks with hole to suit 25mm waste fittings. supplied complete with plug and plastic waste.

Made from U.V. resistant, white ABS plastic, this versatile basin is suitable for use in the galley, head or the aft deck. Supplied complete with plug and 25mm plastic waste fitting.

135034

Length Width Depth Int. Int. mm mm mm

Round Sinks

Oval Basin - Plastic

BLA Code

Overall Length mm

PUMPS, PLUMBING & GALLEY

Rectangular Sinks

3/4

BLA Outside Code Dia. mm

Mount Hole mm

135214 46 rubber33 135202 25mm plug

Intrusion Straight mm 41

Intrusion Hose Elbow Size mm mm 64

www.bla.com.au

199

section

PUMPS, PLUMBING & GALLEY

Clear PVC Hose

Shields Multiflex Hose

Non-toxic, clear vinyl tubing for general use.

Non kink hose with a reinforced black vinyl helix in crystal clear vinyl tube. Smooth bore. Suitable for potable water fill, sinks, bilge pumps, showers, iceboxes and live-well drains (above the waterline). Sold in 30 metre rolls.

BLA Code

ID mm

Length m

136004 136006 136008 136010 136016 136018

6 8 10 13 19 25

30 30 30 30 30 30

Spiralflex Bilge Pump Hose A very flexible smooth bore black plasticised PVC, abrasion resistant and U.V. resistant hose. Reinforced with a spiral wound rigid white PVC coil that maintains form under suction even when bent to the minimum radius. Bend radius is about twice the hose ID thickness. Resists oils, diesel and detergents. Supplied in 30 metre coils.

BLA Code

ID mm

136030 136031 136032 136033 136034

19 25 28 32 38

Fuel Deck Filler Hose A premium grade reinforced rubber type hose, commonly used to connect deck filler to fuel tank, for both diesel and petrol. Black NBR/PVC blended compound with textile cord and spiral wire reinforced interior. Suitable for survey vessels, Lloyds, DNV and Rina approved. Also suitable for use as wet exhaust hose. Sold in 15 metre rolls.

BLA Code

ID mm

136060 136062

38 50

ID mm

136020 136022 136024 136026 136028

19 25 28 32 38

Spigoted Bilge Pump Hose An economical convoluted hose commonly used with submersible electric bilge pumps for bilge water discharge. Convoluted form resists kinking but still bends to a tight radius. Spigots at regular intervals providing a smooth bore, smooth outer section for connection with hose clamp to pump, or above waterline skin fitting. Sold in 15 metre rolls. BLA ID Spigot Code mm Centres mm 136052 136054 136056

19 28 32

300 300 1100

Reinforced Clear Food/Fuel Hose Petrol resistant, multi-purpose (air/ water). Meets AS2070 food contact requirements. Red tracer identifies fuel application suitability. For other fuel hoses refer section 20.

BLA Code

ID mm

Length m

136072 136074 136076 136078 136080

6 8 10 13 16

20 20 20 20 20

BLA Code

ID mm

Length m

136082 136084 136088 136092 136096

19 25 32 38 50

20 20 20 20 20

Shields VAC Sanitation/Bilge Hose

Odour Free Sanitation Hose

Smooth white PVC hose with hard vinyl helix reinforcement, vacuum rated and resistant to odour permeation, mild chemicals and salt water. Sold in 30 metre rolls.

Odour permeation in marine sanitation systems is not only unpleasant but also presents health risks. Odour free sanitation hose has up to five times better resistance to odour permeation than competitor PVC sanitation hoses. Vacuum rated to 90 KPA. Smooth bore and easy clean smooth finish white outer surface. Sold in 20 metre rolls.

Applications include: • Sanitation - toilet to holding tank, holding tank pump out • Bilge pump - intake and outlet • Drains - sinks, scupper, showers • Deckfill - potable water • Livewells - intake & outlet

200

BLA Code

ID mm

BLA Code

ID mm

136126 136128 136136

19 25 38

136142 136144 136146

19 25 38

Quality marine equipment

section

Quick Connect 15

Features: • Unique 'double gripper' provides secure lifelong tube retention even at excessive pressures • Collet has internal support ring ensuring O-ring seal is held in position and does not distort or leak under pressure • The innovative, tube supporting, 'cage collet' design eliminates leaks where fittings are close to tight bends • High integrity single piece moulding for reliability and strength • Outer sleeve incorporates collet cover preventing accidental tube release

To assemble Fig 1

To Disconnect Fig 3

Fig 2

Cut to length by making a straight clean cut (use Whale tube cutters on a mark.

Typical Installation

Simply push the tube into the fitting up to the internal stop.

Push back on the grey collet against the face of fitting.

Fig 4

Hold the collet in and pull out the tube

Quick Connect 15 Tubing

Straight Joiner

Semi rigid tubing. 15mm OD, 11mm ID. Available in red, blue and green, all manufactured to food grade.

In-line connection for Quick Connect 15 tubing.

Ratings: Cold: 12 bar @ 20ºC Hot: 6 bar @ 65ºC

BLA Code 136620

PUMPS, PLUMBING & GALLEY

The Quick Connect 15 water system offers a simple, reliable, time and cost effective, high integrity plumbing system. The only tool required for assembly is a tube cutter. Plumbing can be disconnected and reassembled at any time without tools. All connections are external for minimal flow restriction. All components are manufactured from non-toxic food grade materials.

Elbow Joiner Elbow fitting for use with Quick Connect 15 tubing.

BLA Length Colour Code m 136602 136604 136605 136606 136608 136610

10 10 10 50 50 50

Blue Red Green Blue Red Green

'T' Joiner 'T' piece for use with Quick Connect 15 tubing. BLA Code 136624

End Plug

BLA Code 136622

Stem 'T' 75mm minimum bend radius

Accepts Quick Connect 15 hose on two ends. 15mm stem fitting the other. Can be linked in a manifold fashion. BLA Code 136625

End Stop 15mm End stop fitting for use with Quick Connect 15 tubing.

Internal brass end plug for Quick Connect 15 fittings. BLA Code

BLA Code

136626

136628

www.bla.com.au

201

section

PUMPS, PLUMBING & GALLEY

Push-On Adaptors

Stem Elbow

Adapt existing 11 or 12mm stems to suit Quick Connect 15 fittings.

Elbow fitting accepts Quick Connect 15 tubing one end. 15mm stem fitting the other.

BLA Inside Code Dia. mm 136638 136639

BLA Code

Outside Dia. mm

11 12

136640

15 15

Elbow Adaptor Elbow fitting that accepts Quick Connect 15 tubing one end, 1/2" BSP brass internal thread the other end.

Hose Tail 13mm barbed straight hose tail to Quick Connect 15 tubing.

BLA Code

136641

136642

Thread Adaptors Thread Adaptors

Used to adapt 1/2" BSP and 3/4" BSP threads to Quick Connect 15 tubing.

Used to adapt 1/2" BSP and 3/4". BSP threads to Quick. Connect 15 tubing.

BLA Code 136648

136650

BLA Code 136647 136648 136649 136650

Thread BSP 3/8" 1/2" 1/2"

3/4"

136649

Used to adapt 1/2" NPT and 1/2" BSP thread to Quick Connect 15 fittings.

136651 136653

Thread 1/2" 1/2"

NPT BSP

3/8" 1/2" 1/2" 3/4"

Plastic Brass Plastic white Brass Plastic white

An in-line non-return valve designed to accept Quick Connect 15 tube fittings either end. BLA Code 136654

Hose Tail - Brass

BLA Code

3/8"

Non-Return Valve

Material Plastic Plastic Brass Plastic

136634 136635 136644 136645 136646

Thread Material BSP

Barbed Adaptors Adapts Quick Connect 15 to hose.

Material Brass Plastic

Ball Valve

BLA Description Code 136655 136656 136657 136660 136661

Straight Straight Straight Elbow Elbow

Suits hose I.D. mm 19 16 13 13 19

Polysulphur ball valve with Quick Connect 15 connections both ends. Large easy grip valve control.

Tank Fitting Designed to mount through up to 6mm material for direct connection of Quick Connect 15 tubing to the water tank.

202

BLA Code

136658

136662

Quality marine equipment

section

Solar Shower

Stainless steel reinforced heater hose installed between water heater outlet and system 15 plumbing. 1/2" NPT external thread one end and 1/2" NPT internal thread the other. 400mm in length.

Solar heated portable shower. Made from heavy duty black PVC. Incorporates nozzle, flexible hose and on/off tap. Hang up ‘S’ hook and lanyard included. Fill with water and leave in the sun, out of breeze to heat. 22 litre capacity.

BLA Code 136663

Quick Connect 15 Clip Used to mount quick connect 15 pipe work. BLA Code BLA Code

134412

136664

Water Holding Tanks

Tube Cutters Heavy duty cutter designed to cut Quick Connect 15 tubing squarely.

Roto moulded in 5mm minimum thickness polypropylene, suitable for drinking water. Nine plumbing connection ports all utilising 1½" BSP threads. Tanks are supplied with all ports blank except the top deck filler port. Simply cut out any required port with a 40mm hole saw and screw in 1½" BSP fitting. A range of reducers are available to convert the 1½" BSP port to smaller BSP diameters.

BLA Code

PUMPS, PLUMBING & GALLEY

Heater Connector

136666

Pressure Relief Valve Designed for mounting in-line within the water pressure system for protection of pipes and fittings against over pressure. Pressure relief is preset at (87PSI) 6 BAR. Brass body with 1/2" NPT internal threaded ports.

BLA Code

Litres mm

Length mm

Width Height mm mm

136680

135304 60 400 400 135306 120 800 400 138486 1½" to 1¼" BSP reducer 138487 1½" to 1" BSP reducer 138488 1½" to ¾" BSP reducer 138489 1½" to ½" BSP reducer

Thermostatic Mixer Valve

Three Way Valve Quick Connect Adaptor

Temperature adjustable with integral non return valves on the supply side. Installed in conjunction with water heaters to control the maximum temperature of water at the tap or shower. Factory reset at 43ºC. 1/2" BSP external threaded ports accept Whale System 15 fittings. Nickel plated brass body, stainless steel and heat resistant plastic internals.

Three way ball valve provides two different flow directions. Housing constructed of brass with plastic System 15 Quick Connect Adaptors.

BLA Code

136686

136659

BLA Code

400 400

www.bla.com.au

203

section

PUMPS, PLUMBING & GALLEY

Ball Valves

Skin Fittings - Plastic

- PVC

Totally non-corrosive PVC construction with internal BSP thread. ‘T’ grip handle. One piece injection moulded housing. Alkali and acid resistant. Every valve is factory pressure tested. ISO PSI working pressure.

White moulded plastic through hull fittings. Suitable for most above waterline outlets.

BLA Code

138230 138232 138234 138235 138236 138238

136690 136692 136694 136696 136698 136700

BLA Hose Code Size mm in

Thread Length Width Height BSP mm mm mm 1/2"

80 92 98 113 131 149

3/4"

1" 11/4" 11/2" 2"

32 39 48 58 68 80

65 76 88 102 113 153

White acetal through hull fittings. Suitable for most above waterline outlets.

138240 138241 138242 138244 138246 138248

13 16 19 25 32 38

1/2 5/8 3/4

1 11/4 11/2

21 22 26 32 41 47

13 1/2 16 5/8 19 3/4 25 1 28 11/8 38 11/2

1 11/8 11/4 11/2

75 83 94 84 98 103

Skin Fittings - Stalon

90 90 105 105 108 108 BLA Tail Code

Skin Fittings - Plastic

401670 401672 401671 401673 401674 401677

24 27 34 34 42 48

3/4

Mount O/all Hole Length mm mm

White moulded plastic through hull fittings. Broad flange provides large sealant area. Suitable for most above waterline outlets.

BLA Hose Code Size mm in

5/8

Nylon and stainless steel combined! Glass reinforced nylon with a 316 stainless steel stamped face. Combining the strength and light weight of a reinforced nylon with the aesthetics of polished stainless steel. Suitable for above waterline outlets.

Skin Fittings - Acetal

BLA Hose Code Size mm in

15 19 25 28 32 38

Mount O/all Hole Length mm mm

Flange Hull O.D. Thickness mm mm 38 39 47 57 57 76

32 32 37 38 38 38

138249 138250 138251 138253 138254 138256 138258 138260 138263 138266 138268

Straight Straight Straight Straight Straight Straight Straight Straight 90º 90º 90º

Hose Overall Thread Flange Hull Size Length Dia. Dia. Thickness mm mm mm mm mm 13 16 19 25 28 32 38 50 19 28 38

76 81 86 86 86 104 104 134 88 115 119

21 34 34 34 34 41 41 57 34 41 41

35 48 48 48 48 60 60 82 48 60 60

'L' Head Skin Fittings Manufactured from U.V. stabilised, white acetal. Features 'L' shaped head for lowest possible drainage point. Ideal for cockpit and livewell drains.

Hose Tails - Acetal Top quality white acetal hose tails. BSP thread. BLA Hose Thread O/all Code Size Length mm in bsp mm 138304 138306 138308 138310 138312

204

13 1/2 19 3/4 25 1 32 11/4 38 11/2

1/2" 3/4"

1" 11/4" 11/2"

Quality marine equipment

68 81 81 81 81

36 28 28 28 28 33 33 46 28 28 28

BLA Hose Code Size mm in 138290 19 3/4 138292 25 1 138294 38 11/2 138296 50 2

Mount O/all Hole Length mm mm 26 41 47 62

84 112 137 108

Max. Hull Thickness mm 34 37 60 25

section

Hose Tails - Stainless Steel

100% stainless steel band and worm drive. 136412 - 416 have 8mm wide bands, all other sizes have 13mm wide bands.

Cast 316 grade stainless steel construction. Suitable for survey.

BLA Code

Min. Dia. mm

Max. Dia. mm

BLA Threaded Hose Code Size bsp mm in

136412 136414 136416 136418 136420 136422 136424 136426 136428 136430 136432 136434 136436 136437 136438 136439 136440

5.5 11 13 14 17 21 21 27 33 40 46 57 65 84 48 130 155

16 20 23 27 32 38 44 51 57 64 70 76 89 108 127 150 178

136920 136922 136924 136926 136928 136930

Hose Clamps

Ball Valves

Size mm

136520

Combines a thru-hull skin fitting cast into a water scoop strainer. 316 grade solid cast construction. Earth/anode wire connection tab is included on 1/2" to 1½" sizes. Suitable for survey.

½" ¾" 1" 1¼" 1½"

62 74 86 90 120

32 42 50 64 74

70 85 105 110 130

Handle Radius mm 105 130 145 155 190

Cast 316 grade stainless steel construction. Highly polished mount flange. Internal lugs to hold fitting during installation. Fully threaded for direct connection to ball valve. Suitable for survey.

136940 1/2" 136942 3/4" 136944 1" 136946 1¼" 136948 1½" 136950 2"

64 74 78 87 87 96

Cast 316 grade stainless steel construction. Highly polished mount flange. Internal lugs to hold fitting during installation. Barbed tail for hose connection. BLA Code

136970 136972 136974 136975 136976 136978

138270 138272 138274 138276 138278 138280

57 62 62 85 88 88

Overall Length mm

Skin Fittings - Stainless Steel

BLA Thread Thread Width Scoop Scoop Code Length Depth Length bsp mm mm mm mm

1" 1¼" 1½" 2"

- Stainless Steel

BLA Thread Length Width Height Code BSP mm mm mm

BLA Thread Code bsp

Scoop Skin Fittings - Stainless Steel

3/4"

63 63 72 81 90 98

Skin Fittings - Stainless Steel

48-51 52-55 56-59 60-63 62-65 71-76 89-94 101-107 113-121 140-148 162-174

1/2"

13 ½ 19 ¾ 25 1 32 1¼ 38 1½ 50 2

- ‘T’ Bolt Tridon

136900 136902 136904 136906 136908

136518 136520 136522 136524 136525 136529 136535 136539 136542 136547 136550

Overall Length mm

Cast 316 grade housing. Stainless steel ball, stem, handle, nut & spring washer. Two piece, full bore design with teflon seals for smooth operation. Suitable for survey. Slide gate on handle locks in fully open or fully closed position.

Used where optimum clamping security is essential i.e. engine cooling/exhaust systems, bilge pumping systems and sanitation plumbing. Solid 304 grade stainless steel construction. Rolled edges to prevent clamp cutting into hose. Hex head adjustor bolt.

BLA Code

½" ¾" 1" 1¼" 1½" 2"

PUMPS, PLUMBING & GALLEY

Hose Clamps

48 58 60 65 70 85

18 25 25 32 32 32

64 100 100 120 120 150

Mount Hose Hole Size mm mm in 32 32 32 45 45 56

3/4

19 25 1 28 11/8 32 1¼ 38 1½ 50 2

Length mm 75 75 75 88 88 134

www.bla.com.au

205

section

Ball Valves - Bronze

PUMPS, PLUMBING & GALLEY

Bronze ball valves. Stainless steel handle. BSP thread for direct connection to through hull fitting.

BLA Thread Length Width Height Code bsp mm mm mm 137004 1/2" 137006 3/4" 137008 1" 137010 1¼" 137012 1½" 137014 2"

53 60 74 82 92 105

29 37 47 57 66 84

80 100 125 125 160 160

137010

Three Way Valves - Chrome Plated Brass

Ball Valves - Chrome Plated Brass

Chrome plated brass. Three way ball valves provide two different flow directions and is perfect for control of separate fuel tanks. Nickel plated handle. BSP threaded ports.

Chrome plated brass ball valve with stainless steel handle, ideal for fuel line installations. BSP threaded ports.

BLA Thread Length Width Height Handle Code Radius bsp mm mm mm mm 137072 137074

3/8" 1/2"

52 64

28 35

68 76

95 95

BLA Thread Length Width Height Handle Code Radius bsp mm mm mm mm 137050 137052 137054

1/4" 3/8" 1/2"

44 44 50

24 24 30

50 50 60

Skin Fittings - Bronze

Hose Tails - Bronze

Cast bronze through hull fittings. BSP thread. Suitable for survey.

Cast bronze tails to suit most hose sizes. BSP threaded, suitable for survey.

BLA Thread O/all Flange Code Length OD bsp mm mm

BLA Hose Thread O/all Code Size Length mm in bsp mm

138034 138036 138038 138040 138042 138044

138004 138006 138008 138010 138012 138014

1/2" 3/4"

1" 1¼" 1½" 2"

68 74 78 86 91 108

48 52 54 70 72 89

13 19 25 32 38 50

1/2 3/4

1 1¼ 1½ 2

1/2" 3/4"

1" 1¼" 1½" 2"

48 53 68 78 83 88

Scoop Skin Fittings - Bronze

Elbow Tails - Bronze

Combines a through hull skin fitting cast into a water scoop and strainer. BSP thread.

90º cast bronze elbow with a BSP thread one end and a barbed hose tail on the other end.

BLA Thread Length Width Code bsp mm mm 138074 138076

206

60 73 90 96 112 130

Handle Radius mm

1/2" 3/4"

100 100

Quality marine equipment

72 72

Scoop Mount Depth Screws mm mm 25 25

4 c/s 4 c/s

BLA Thread Hose Code Size bsp mm in 138060 138062 138064 138066 138068

3/4"

1" 1¼" 1½" 2"

19 25 32 38 50

3/4

1 1¼ 1½ 2

85 85 85

section

Impact Drain

Mounts over existing through hull fitting to strain and scoop water. Available in cast bronze or black plastic.

Moulded in black or white high impact U.V. resistant plastic. Features low profile flush head, raised ribs for maximum grip and large bore for optimal drainage. Easy installation simply drill hole and tap into place.

BLA Colour Code BLA Material O/all Width Code Length mm mm 138850 138852 138854 138856

Plastic Bronze Bronze Bronze

120 121 178 194

Scoop Mount Depth Screws mm mm

80 84 121 127

20 21 25 44

3 4 5 5

c/s c/s c/s c/s

90º brass elbow with a BSP thread one end and a barbed hose tail connection on the other end. BLA Thread Hose Code Size bsp mm 1/4" 1/4" 1/4" 3/8" 1/2"

138206 138208 138210

NPT BSP BSP BSP BSP BSP BSP BSP NPT NPT

16 16 25 25 28 28

17 17 26 26 32 32

Mount Hole mm

Outside Dia. mm

O/all Length mm

25 22 22

30 32 32

14 57 83

These covered drains combine smart aesthetics with easy single hole installation for anchor wells, motor wells, etc. Rounded no catch, cast and highly polished 316 stainless steel head coupled with glass reinforced nylon stem.

Brass hose tails suitable for use with fuel valves and fuel lines. Thread one end and barbed hose tail connection on the other end.

1/4" 1/8" 1/4" 1/4" 1/4" 3/8" 3/8" 3/8" 3/8" 3/8"

39 39 44 44 51 51

Covered Drains

Tails - Brass

138130 138132 138134 138136 138137 138138 138140 138142 138148 S18-8109

26 26 39 39 44 44

Well Drains - Nylon

BLA Code

6 8 10 10 19

BLA Thread Code

Black White Black White Black White

Hose Mount Size Hole mm

Serrated press fit installation. Use of sealant recommended. Two piece injection moulded nylon construction.

Elbow Tails - Brass

138102 138104 138106 138108 138114

138164 138166 138172 138174 138180 138182

Flange Length O.D. mm mm

Hose O/all Size Length mm mm 6 8 8 6 10 6 8 10 10 8

40 34 40 40 42 40 40 43 43 44

PUMPS, PLUMBING & GALLEY

Scoop Filters

BLA Hose Cover Mount Length Max. Hull Code Size Hole Thickness mm mm mm mm mm 138212 – 138214 19

47x40 49x40

25 25

76 114

50 50

90º Through Hull Tails Through Bulkhead Connector Installed where hoses need to pass through bulkheads, even watertight bulkheads. Nylon construction suitable for potable water, saltwater or bilge water.

90º through hulls or bulkhead tails are ideal for tight spots where hose is difficult to route without kinking. Durable polypropylene construction. Suitable for potable water, saltwater or bilge water.

BLA Hose Code Size mm 138802 19

Bulkhead Length Flange Max. Thick OD mm mm mm 26

128

BLA Code 138804 138808

Hose Size mm 19 28 & 30

a Flange Mount Length Max. Dia. Hole mm mm mm mm 22 47

38 61

22 31

64 111

www.bla.com.au

207

section

PUMPS, PLUMBING & GALLEY

Hose Tails

Reducer Hose Tails

BSP external thread to barbed hose tail, for connecting flexible hose to valves, etc. Made from polypropylene.

BSP external thread to barbed hose tail. Different thread and hose sizes to adapt different diameter plumbing.

BLA Thread Hose Code Size bsp mm in 138332 138333 138336 138337 138339 138341 138357

BLA Thread Hose Code Size bsp mm in 138324 138325 138326 138327 138328 138329

1/2" 3/4"

13 19 25 32 38 50

1" 1¼" 1½" 2"

1/2 3/4

1 1¼ 1½ 2

1/2

13 25 19 32 25 25 19

1" 1" 1¼" 1½" 3/4"

3/4

1¼ 1 1 3/4

'T' Hose Tails

Elbow Hose Tails

BSP external thread with barbed hose tails. Made from polypropylene.

BSP external thread to barbed hose connection 90º bend. Made from polypropylene.

BLA Thread Hose Code Size bsp mm in 138384 138385 138386 138387 138388 138389

BLA Thread Hose Code Size bsp mm in 138364 138365 138366 138367 138368 138369

1/2" 3/4"

13 19 25 32 38 50

1" 1¼" 1½" 2"

1/2 3/4

138424 138425 138426 138427 138428 138429

1/2 3/4

BLA Hose Size Code mm in mm

1 1 1¼ 1½

1/2 3/4

1 1¼ 1½ 2

BLA Hose Code Size mm in

1 1¼ 1½ 2

1/2 1/2 1/2 1/2 3/4 3/4 3/4

13 19 25 32 38 50

Straight hose joiner with a barbed hose fitting at each end. Made from polypropylene.

138444 138445 138446 138447 138448 138449

Straight hose joiner for in-line connection of dissimilar hose sizes. Different size barbed hose fittings at each end. Made from polypropylene.

13 13 13 13 19 19 19 25 25 32 38

1 1¼ 1½ 2

Hose Joiners

Reducing Hose Joiners

138464 138465 138466 138467 138468 138469 138470 138471 138472 138473 138474

1" 1¼" 1½" 2"

1/2 3/4

BLA Hose Code Size mm in

Three way 'T' shaped hose connection, with barbed hose tails. Made from polypropylene.

13 19 25 32 38 50

90º elbow joiner with a barbed hose fitting at each end. Made from polypropylene.

'T' Hose Joiners

138404 138405 138406 138407 138408 138409

1/2" 3/4"

Elbow Hose Joiners

1 1¼ 1½ 2

BLA Hose Code Size mm in

208

3/4" 3/4"

to to to to to to to to to to to

19 25 32 38 25 32 38 32 38 38 50

Quality marine equipment

in 3/4

1 1¼ 1½ 1 1¼ 1½ 1¼ 1½ 1½ 2

13 19 25 32 38 50

1/2 3/4

1 1¼ 1½ 2

Through Deck Hose Fitting Black polypropylene fitting designed for installation through deck or bulkhead. 19mm hose tail on inside of the flange fitting and a 3/4" external thread on the outside. External access adjustable flow valve and sealing cap. BLA Protrusion Intrusion Flange Mount Code mm mm Dia. Holes mm mm 138800

4 c/s

section

Reducing Bushes

Hex Nipples

BSP thread internal and external. Made from polypropylene.

External BSP thread joiner. Made from polypropylene.

138480 138482 138484 138486 138487 138488 138489

Internal Thread bsp

3/4"

1/2" 3/4"

1" 1¼" 1½" 1½" 1½" 1½"

1" 1¼" 1" 3/4" 1/2"

BLA Code 138494 138495 138496 138497 138498 138501

Thread bsp

PUMPS, PLUMBING & GALLEY

BLA External Code Thread bsp

1/2" 3/4"

1" 1¼" 1½" 1¾"

Elbow Coupling BSP internal thread to BSP internal thread joiner. 90º bend. Made from polypropylene.

Couplings Internal BSP thread joiner. Made from polypropylene. BLA Code 138514 138515 138516 138517 138518

Thread bsp

138522 138524 138526 138528 138530

1/2" 3/4"

1" 1¼" 1½"

138506 Coupling reducer 1 x 3/4"

End Plugs External BSP thread end plug. Made from polypropylene. BLA Code 138534 138535 138536 138537 138538

Thread bsp 1/2" 3/4"

1" 1¼" 1½"

For mounting PVC and semi-rigid plumbing. Made from polypropylene. Sizes marked on the clips correspond with the inside diameter of polypipe.

BLA Pipe Code Size mm in 13 19 25 32 38 50

Thread bsp 1/2" 3/4"

1" 1¼" 1½"

End Caps Internal BSP thread end cap. Made from polypropylene. BLA Code 138554 138555 138556 138557 138558

Thread bsp 1/2" 3/4"

1" 1¼" 1½"

Manifolds

Heavy Duty Pipe Clips

138574 138575 138576 138577 138578 138579

BLA Code

1/2 3/4

1 1¼ 1½ 2

Designed for installation in-line in 38mm (1½") flexible pipe, this fitting enables multiple drainage from up to three services to one through hull skin fitting, saving on installation costs and labour. Made from ST801 nylon.

BLA Main Take Code Line Offs mm in mm in 138594 138596

38 1½ 38 1½

19 3/4 25 1

Tube Clips

Camlock Pump Out Adaptors

For mounting flexible or rigid tube. The unique design enables these clips to accept a wide range of tube diameters. Made from nylon. Sold as a card of 12.

Screws into deck fillers to allow onshore pump out facilities to take suction on built in sullage tanks. The camlock fitting of the pump out station couples over this fitting. The camlock is referred to as Type 40.

BLA Pipe Size Code mm in 193824 25-38 1-1½ 193826 45-60 1¾-2¼

53 43

BLA Material Suits Thread Code Deck Filler BSP 139290 Poly 139292 Bronze 139294 Poly

192315 192315 192311 & 192335

1½" 1½" 1¼"

www.bla.com.au

209

section

PUMPS, PLUMBING & GALLEY

Through Transom Scupper

Water Strainers

Designed for installation in transom of boats with self-draining cockpits. The rubber flapper opens to dump water out and closes to prevent backwash from entering cockpit. Tough acetal construction. Above waterline installation only.

Perko water strainers are designed for easy mounting and cleaning. They have cast bronze top and bottom housings and a drain plug in the base for easy sediment removal and draining. 304 grade stainless steel strainer.

- Bronze

BLA Hose Max. O/all Scupper Mount Code Size Thickness Length Dia. Hole mm in mm mm mm mm 138812

38 1½

153

BLA Code

Designed as a water exit for boats with self draining cockpits. Scupper mounts over flush transom drains above the waterline. The rubber flapper opens to dump water out and closes to prevent backwash. Tough acetal mount flange.

138814

Diameter ID OD mm mm 70

Cockpit Drain

BLA Code 138018 138020 138022 138024

Mount Screws mm

138816

105

230 115 115 255 138 138 270 138 138 335 175 182 tails to suit above:

Hose Size Length mm mm

3/4"

19 25 32 38

1" 1¼" 1½"

45 45 52 58

Utility water filter. ABS plastic housing. Clear Marelon cover. Nylon filter element. Easily dismantled for cleaning.

- With Screen

O/all Flange Length Dia. mm mm

Thread NPT

Width Depth mm mm

Water Strainers

4 c/s

Drain design features a short stem and narrow flange for installing through cockpit floors. Removable screen to prevent hose clogging. Narrow flange allows recessed installation for complete draining. Durable polypropylene construction. BLA Code

Height mm

3/4" 401642 401644 1" 401646 1¼" 401648 1½" Bronze NPT straight

Scupper Valve

BLA Code

Port npt

Hose Size mm

Mount Hole mm

138866

Cockpit Scupper

138864

Cast 316 Grade stainless steel housing. Removable strainer with a rubber check ball to prevent back flow. Outlet is angled at 45º. Screw removal key included.

BLA Capacity Port Code Thread l/m BSP

Dia.

Height

138864 138866

142 142

120 180

150 300

3/4"

1½"

Drain Cover - Stainless Steel Polished stainless cover for floor drains and vents.

210

BLA Hose Flange Grate Intrusion Cut Mount Code Size O.D. O.D. Out Screws mm in mm mm mm mm mm

BLA Diameter Mount Code Screws mm mm

138817 38 1½

138822

Quality marine equipment

120

4 c/s

4 r/h

section

Vented Loops

A large capacity breather for water and waste tanks. Meets requirements of Australian Standards for venting black waste holding tanks. Installs through hull or deck, skin fitting style. Removable 90º tail accepts 38mm hose. Off white injection moulded plastic construction. Not suitable for use as a fuel breather.

Installed in toilet systems where the toilet or holding tank is below waterline or near waterline, to prevent sea water from siphoning through the toilet system, potentially swamping the vessel. Inlet and outlet plumbing is looped well above waterline and the vented loop is installed at the top of the loop, preventing siphoning. When installing ensure the vented loop will remain above water line when boat is fully loaded and or heeled.

BLA Code

Head Protrusion Max. Deck lxw Thickness mm mm mm

139080

76x67

139090

Covered Toilet Roll Holder This toilet roll holder fully encases the paper roll ensuring the paper is kept dry. Mounts on any flat vertical surface concealed mount fastenings. Moulded in smooth white ABS plastic. BLA Width Code mm

Height mm

Depth mm

139002 142

147

135

139092

139096 Toilet below the waterline

Recessed Toilet Paper Holder

Cut Out mm

139004 150x150

To remote breather

At least 20cm

38mm Vented Loop

Holding tank above discharge elbow at any time

Flush appearance to match todays interiors. The design keeps paper dry and out of sight while still being conveniently at hand. Perfect for heads where space is limited. Moulded in smooth white ABS plastic.

BLA Code

Toilet (above or below the waterline) discharging into Holding Tank.

19mm 38mm Vented Loop Vented Loop

38mm Vented Loop

To remote breather

At least 30cm

38mm Seacock 19mm Seacock Discharge Elbow

Holding tank below discharge elbow

BLA Hose Height Width Depth Code Size mm in mm mm mm

Width mm

Height mm

Depth mm

190

185

132

139090 139092 139096

19 3/4 25 1½ 38 1½

75 100 130

96 150 200

25 43 55

PUMPS, PLUMBING & GALLEY

Tank Vent

Mount Holes mm 6 r/h 6 r/h 6 r/h

Waste Holding Tanks Roto moulded in 5mm minimum thickness polypropylene, suitable for grey or black waste. Nine plumbing connection ports all 1½" BSP threaded. The 132210 and 132212 macerator toilet pump (refer page 214) can be directly threaded into any of these connection ports, without any plumbing required. Tanks are supplied with all ports blank except the top deck pump out port. Simply cut out any required port with a 40mm hole saw and screw in 1½" BSP fitting. A range of reducers are available to convert the 1½" BSP port to smaller BSP diameters.

BLA Litres Code 139338 139342 138486 138487 138488 138489

60 120 1 1 1 1

½" ½" ½" ½"

to to to to

Length mm

Width mm

Height mm

400 800

400 400

1¼" BSP reducer 1" BSP reducer 3/4" BSP reducer 1/2" BSP reducer

www.bla.com.au

211

section

Electric Marine Toilets

PUMPS, PLUMBING & GALLEY

The TMC range of marine electric toilets offer a wide variety of styles and sizes to suit the requirement of virtually any boat. Common Features: • Top quality vitreous china bowl • Self macerating combined, water in, waste out pump • Convenient push button operation • Supplied with switching • Supplied with 25 to 38mm outlet adaptor if retro fitting in place of a manual toilet • Suitable for installation with Autosan 139098 & 100

Luxury Electric Toilets A contemporary styled large bowl toilet with fully enclosed motor and plumbing connections, for smart aesthetics and easy cleaning. BLA Power Width Height Code volts amp mm mm 139098 139100

12 20 24 10

366 366

Front Inlet Outlet To Back mm mm mm

447 447

470 470

25 25

Mount Holes mm 10 r/h 10 r/h

Deluxe Electric Toilets

139118 & 20

This new Euro styled toilet has large bowl sizing but in a lower profile (medium height). Fully enclosed motor and plumbing connections, protects motor and is easy to clean. BLA Power Width Height Code volts amp mm mm 139118 139120

12 20 24 10

368 368

Front Inlet Outlet To Back mm mm mm

388 388

490 490

25 25

Mount Holes mm 10 r/h 10 r/h

Standard Electrical Toilets Available in small and large bowl sizing. Now with protective motor cover.

139102 & 04

BLA Bowl Power Width Height Front Inlet Outlet Mount Code Size To Back Holes volts amps mm mm mm mm mm mm 139102 139104 139106 139108

Small Small Large Large

12 24 12 24

20 10 20 10

340 340 365 365

340 340 380 380

440 440 490 490

25 25 25 25

10 10 10 10

r/h r/h r/h r/h

N.B. If installing TMC electric toilets below or near water line fit vented loops to inlet and outlet plumbing, refer page 211.

Spare Parts BLA Code

Description

139194 Service kit all models (21, 26, 27, 28, 29, & 30) 139202 Replacement 12 volt motor (31) 139204 Replacement 24 volt motor (31) 139206 Base to suit standard toilet (22, 39, 23, 24, 37 & 42) 139216 Motor cover (55) 139230 Discharge port (24) 139232 Sleeve (17) 139234 Waste water impeller (18) 139236 Macerator blade set (20, 20-1) 139238 Flapper valve (23) 139240 Shaft ‘O’ ring (34) 139242 Clean water pump impeller (29) 139244 Discharge elbow, luxury and deluxe (64) 139256 Small china bowl (1) 139258 Small lid only (3) 139260 Small seat only (2) 139264 Small lid, seat and hinges (2, 3, 4, 5, 6, 7 & 8) 139212 12V toilet conversion kit (converts manual TMC toilet into std electric toilet) 139214 24V toilet conversion kit (converts manual TMC toilet into std electric toilet) N.B. 2001 and later toilets have 25mm (1") inlet, prior models have 20mm ( 3/4") inlets.

212

Quality marine equipment

Included hardware

139106 & 08

Luxury & Deluxe models

section

Manual Marine Toilets The TMC manual marine toilet range offers a variety of sizes and styles, based on a time proven reliable design.

PUMPS, PLUMBING & GALLEY

Common Features: • Top quality vitreous china bowl • Flush and dry bowl pump cycles to control bowl water level • Discharge outlet swivels 360º to accommodate various discharge plumbing directions • Pump and bowl can be reversed for left or right hand pumping as well as to suit installation requirements • Stainless steel fastenings used throughout • No power requirement, particularly important on cruising yachts where power consumption is critical

139110

Vertical Pump Toilets • Available in small or large bowl • Small bowl style with vertical pump fits in compact spaces such as under ‘V’ berths BLA Bowl Width Height Depth Inlet Outlet Code Size mm mm mm mm mm 139110 Small 139112 Large

470 500

320 350

430 490

19 19

38 38

Mount Screws mm

139112

8 r/h 8 r/h

Lever Pump Toilet A small bowl configuration manual toilet with easy action lever operated pump. BLA Bowl Width Height Depth Inlet Outlet Code Size mm mm mm mm mm 139114 Small

470

340

430

Mount Screws mm 8 r/h

139114

N.B. If installing TMC manual toilets below or near waterline, fit vented loops to inlet and outlet plumbing, refer page 211.

Spare Parts BLA Code

Description

139250 Repair kit for TMC manual toilets (16, 17, 24, 30, 32, 33, 38, 40, 42, 43 & 44) 139252 Vertical action pump handle (23) 139254 Vertical action pump complete (16-49, 49-56) 139256 Small china bowl only (1) 139258 Small lid only (3) 139260 Small seat only (2) 139262 Plastic base (39) 139264 Small bowl toilet lid, seat and hinge set (2, 3, 4, 5, 6, 7 & 8)

www.bla.com.au

213

section

PUMPS, PLUMBING & GALLEY

Portable Chemical Toilet Portable chemical toilets are a practical option, particularly for trailerable boats, in regions where sewage is not permitted to be discharged overboard. The toilets consist of an upper fresh water holding tank and a sealed lower waste tank locked with a positive catch. The Springfield toilet is manufactured of a light, durable moulded high density polyethylene which facilitates easy cleaning. The fresh water tank utilizes a simple but reliable bellows flush pump. Waste tank separates from rest of toilet to allow emptying into a domestic toilet or sewage collection point. BLA Code

Depth mm

139400

410

Width Height Flush Tank Hold Tank mm mm Capacity Capacity 365

314

12L

11L

Macerator Pumps

Electric Toilet Flush Control

Self priming toilet waste pump. Combines pre-macerator with impeller pump. Designed for in line installation on holding tank pump out or to convert manual vacuum toilets to electric operation. Do not run dry.

A simple one touch contoured control panel featuring built in micro control system allowing two flush options for TMC 12 and 24 volt electric toilets. Features:

Capacity: • 50 l/m open flow • Lift 1.5 metres • Head 5 metres • Inlet 38mm barbed and 1½" BSP • Outlet 25mm barbed

• Half flush option provides a flush operating for five seconds with approximately two litre water delivery • Full flush option provides a flush operating for ten seconds with approximately four litre water delivery • Control panel is equipped with seals for splash proof protection • For convenience a mountable spare fuse holder is provided with six spare fuses For additional safety a maximum 40 amp built in relay circuit helps protect the electric toilet against high current surges caused by excessive impellor friction or sudden start up surge.

BLA Power Length Width Height Code v amp mm mm mm 132210 12 12 283 120 132212 24 6 283 120 139242 Replacement impeller 139236 Macerator blade set

98 98

Mount Screws mm 5 r/h 5 r/h

BLA Code

Volt

139060 139062

12 24

Galleymate 1000 Two Burner Gas Barbecue The Galleymate 1000 can be used to barbecue, cook a roast dinner, bake bread or cakes or just boil the kettle. Supplied as standard with a heavy duty, solid stainless steel flat plate which can easily be removed to allow a standard size frying pan and small pot or saucepan to fit comfortably side by side on the optional cooking rack. By using only the front burner and closing the lid, you can use it as an oven which will cook in around the same time as your home oven. The cooking rack sits down low above the burners to allow maximum heat efficiency and economical use of gas. Supplied as standard with four rubber encased mount legs for use in horizontal, static appliations. Other mounts available to suit most other applications. Features: • Two S/S burners with separate controls • Piezo ignition • 304 grade stainless steel construction • 20,000 BTU output • Barbecue stove top and oven all in one

BLA Code 139540 139550 Cooking rack 139552 Utensil tray 139560 Flush mount kit 139564 Railmount kit 139568 Adjustable rod holder mount 139570 Optional telescopic support t/s 139564 139572 Gas regulator and 900mm hose

214

Quality marine equipment

139540

139564 139560

section

Gourmet Series Gas Barbecues

Pictured with Coleman® disposable gas cylinder (not included)

Features: • Dependable Piezo Crystal Ignition system • Full size inner safety shell funnels grease into front access grease tray reducing flare-up and heat discolouration • Convenient snap-out dual radiant plate for even heat distribution • Closely spaced grill wires designed to grill anything from a T-bone to delicate fish and cut vegetables • Oversized perfectly balanced lockable lid won't slam shut and secures all inner components while underway • One year warranty Catalina and Monterey Additional Features: • Easy to read all stainless steel hermetically sealed thermometer with 750 degree safety glass • Large upper grill for slow grilling or for warming food such as vegetables and bread

Catalina - Pictured with optional cutting board and dual rail mount.

Now includes fold-up legs on all gourmet BBQs

PUMPS, PLUMBING & GALLEY

The versatile gourmet series barbecues have set a new bench mark for onboard cooking. Beautifully finished and manufactured from 100% 18-9 stainless steel for ultimate hygiene and corrosion resistance. They grill quickly, evenly and disassemble easily for cleaning. A wide range of mount options are available to suit virtually any craft. Mount hardware purchased separately. Supplied with control valve for connection to regulated LPG. Purchase of 139632 enables connection to onboard gas supply. Alternatively the Newport is available with control valve to suit Coleman® disposable cylinders.

Monterey - Pictured with optional cutting board and dual rail mounting kit.

Newport - Pictured with optional Coleman® disposable cylinder and Levelock rod holder mount.

BLA Model Control Valve Code To Suit

Primary Grill mm

Secondary Grill mm

Width Incl. Valve mm

139586 139590 139594 139595

300x610 300x460 230x460 230x460

140x610 140x460 – –

730 580 580 580

Monterey Catalina Newport Newport

LPG LPG LPG Coleman®

Front To Back Height (Legs Up) Open Closed Open Closed mm mm mm mm 395 395 300 300

375 375 295 295

480 480 420 420

345 345 290 290

Accessories: 139599 Control valve to connect Monterey to Coleman® disposable gas cylinder 139625 Control valve to connect Catalina to Coleman® disposable gas cylinder 139720 Cooking grill piece suit Catalina and Monterey 139722 Cooking grill piece suit Newport 139724 Warming rack to suit Monterey 139726 Warming rack to suit Catalina

www.bla.com.au

215

section

PUMPS, PLUMBING & GALLEY

Gourmet Barbecue Cutting Shelf

Locking Flush Socket Deck Mounts

Detachable serving shelf made from 18-8 stainless steel with removable, U.V. stabilised food grade polyethylene cutting board. Easily detached for clean-up and storage inside the barbecue when not in use.

Mirror polished 18-8 stainless steel construction. These flush socket sets feature a push button locking pin and include flange gasket with attached water seal plugs. Screws for attachment to table or Gourmet series barbecue included. Single post mounts also suit 139660 cutting table. Dual post mounts also suit First Mate table.

BLA Code 139598

Length Width mm mm 440

190

Levelock Rod Holder Mount Made from a combination of stainless steel and anodised aluminium. The quick release, cam action design allows convenient all angle adjustment. The stainless steel tube fits most cross pin type rod holders in eight different rotational positions. Folds flat for compact storage.

BLA Style Suits Gourmet Barbecue Code 139680 139682

Single Dual

Newport only All models

Deck Cut Flange Out mm mm 60 60

25 25

Intrusion mm 45 45

Rail Mount Kits Made of 18-8 stainless steel and 356 anodised aluminium, they easily detach without tools for compact storage. Single mounts attach to horizontal round rails and feature two way angle adjustment for perfect horizontal levelling. Dual rail mounts have a unique pivoting design which allows them to mount on a straight or curved rail or across the corner of a stern rail.

BLA Code 139678

Overall Tube Length Length 360

300

N.B. Recommended for use with the Newport Gourmet Series barbecue only.

Gourmet Barbecue Covers Made from black Sunbrella® boat cover material. Water, sunlight, mildew and rot resistant.

BLA Style Suits Gourmet Code Barbecue

Rail Diameter mm in

139684 Single Newport only 25 1 139686 Single Newport only 32 1¼ 139688 Dual All models 22-25 7/8-1 139690 Dual All models 28-32 11/8-1¼ 139778 Spare lever and washer

Square Rail/Side Mount These all 18-8 stainless steel mounts attach to flat surface such as bulkheads, coamings, transoms or cabin sides. Also mounts to square and flat rails. Fits horizontal rails up to 57mm high by any depth or vertical rails up to 41mm wide by any depth. Single mounts also suit 139660 cutting table. Dual configuration also suits First Mate table.

216

BLA Code

Suits

139698 139702 139706

Monterey Catalina Newport

Quality marine equipment

BLA Style Suits Gourmet Code Barbecue

Mount Overall Base Height mm mm

139694 139696

69x79 69x79

Single Dual

Newport only All models

110 110

section

Magma Charcoal Kettle Barbecues

PUMPS, PLUMBING & GALLEY

The original and still the best marine charcoal barbecue – available in ‘Original size’, and 'Party size' with 33% more cooking area. Meticulously crafted in 100% 18-9 mirror polished stainless steel for maximum corrosion resistance. Starts easily in windy conditions by using the lid as a windshield. The rotating, adjustable height cooking grill and variable temperature draft control door enables full control over the cooking process. The design allows oven type baking to enhance the barbecue flavour while retaining the natural juices in the food. It will cook more food faster on less grill area than any other charcoal barbecue. Full closure of the temperature draft control door extinguishes the coals for safety, allowing them to be reused for greater efficiency. Mount hardware purchased separately. Features: • Attached grill and lid (lid acts as a shield in gusty wind conditions) • Attached rotating adjustable cooking grill • Complete temperature control • Lower charcoal grate and sealed ash compartment • Mounting options adapt to any boat

Easy disassembly without tools

Pictured with on shore stand, not included GM A M

A PRODU C T S

MARINE KETTLE

139650

BLA Size Code

Cooking Area cm2

Diameter

Height

139602 Original 994 368 320 139604 Party 1317 432 320 139642 Railmount kit 22-25mm - refer page 219 139643 Railmount kit 28-32mm - refer page 219 139644 Deck mount kit - refer page 219 139646 Rod holder mount kit - refer page 219 139648 On shore stand - refer page 219 139650 Blue cover bag - Original 139651 Blue cover bag - Party 139654 Easy lite charcoal starter 139759 Radiant Plate t/s kettle original 139772 Lid knob assembly 139776 Bracket and clamp assembly (G)

139654

(G)

www.bla.com.au

217

section

PUMPS, PLUMBING & GALLEY

Magma Marine Kettle 2

- Combination Stove & Gas Barbecue

Don't be fooled by cheap imitations. Only Magma's patented ‘Marine Kettle 2’ design will give the safety, durability, flexibility and performance that you require from your marine barbecue. Patented stainless steel radiant burner plate and dome system allows you to place standard pots and pans directly over the flame. The Magma barbecue is a complete cockpit cooking centre; you can boil, fry, heat, brew, grill, saute', simmer, stew and bake at your leisure, all the time sealing in the natural flavours and aromas. Great for boats without a galley. Made entirely of 18-9 stainless steel with super efficient burner plate, a Magma barbecue will use less fuel, heat up faster, and have you cooking in no time at all. New lid design is permanently connected so it can't blow overboard. Creates wind shield in open position, or can be closed for controlled convection cooking. Clean up is easy, a twist of the burner instantly disassembles the barbecue for simple cleaning. Mount hardware purchased separately.

Made

USA in the

Two gas supply options: 1. Control valve for connection to regulated LPG. 2. Control valve that screws directly to Coleman® 450 gram disposable propane cylinders.

Pictured with Coleman® disposable cylinder. Mount bracket not included.

The only true combination grill, stove and oven

The Magma Advantage Magma’s patented design. Creates fast, efficient convection cooking.

Entire grill is 100% mirror polished 18-9 stainless steel construction.

NEW ‘stay cool’ 18-9 cast stainless steel handle. With air cooled supports.

NEW Balanced hinged lid. will not slam shut as boat rolls.

NEW heavier gauge stainless steel and brass burner design.

Fully double lined stainless steel. Stays cooler for safety. Guards against discolouration. Adds years of life to the grill.

NEW reliable piezo igniter. For easy, dependable push button lighting.

Cast 18-9 stainless ‘L’ bracket mount clamp. Indexed for easier positive, non slip level mounting.

BLA Style Code 139619 139621 139622 139623 139642 139644 139648 139651 139764 139643

218

Control Valve To Suit

Original LPG Party LPG Original Coleman® Party Coleman®

Cooking Diameter Height Area mm mm cm2 994 1317 994 1317

368 432 368 432

Rail mount kit 22-25mm - refer page 219 Deck mount kit - refer page 219 On shore stand - refer page 219 Blue cover bag - Party size Cooking grill for Party size Rail mount kit 28-32mm - refer page 219

Quality marine equipment

Windproof swivelling turbo venturi tube. Virtually eliminates blow-outs.

285 285 285 285 139646 139650 139750 139754 139762 139774

Rod holder mount kit - refer page 219 Blue cover bag - Original size Burner plate and dome Turbo Venturi tube Cooking grill for Original size Bracket and clamp assembly

NEW burner and heat distribution design. Uses patented hi-tech radiant plate and dome system. Less flare up, even heat distribution and longer grill life. Allows use as a grill, stove or oven.

section

Magma Kettle and Kettle 2 Mounting Hardware All mounts (on this page) fit all Magma Kettle and Kettle 2 barbecues.

PUMPS, PLUMBING & GALLEY

Round Rail Mount This round rail, quick disconnect, all angle mounting bracket is made entirely of 18-8 stainless steel and 356 anodised aluminium to endure the most severe marine environment. Fits any angle railing and detaches quickly for storage without tools, leaving no hardware on the rail. BLA Rail Dia. Code mm in 139642 139643

22 - 25 7/8 - 1 28 - 32 11/8 - 1Â˝

Length mm 300 300

139778 Spare lever & washer 139780 7/8" to 1" adaptor sleeve

Deck Mount Triple chrome plated brass deck socket with 18-8 stainless steel support rod. A stainless detent pin lets the barbecue rotate and lock in eight different positions. Rod portion of mount quickly disconnects for compact storage.

BLA Code 139644

Socket Base mm Ă¸

Socket Height mm

Overall Turn Height Radius mm mm 238

235

Mount Holes mm 6 r/h

Rod Holder Mount Made of 18-8 stainless steel and durable all weather plastic, this versatile mount fits most cylindrical type rod holders 38-48mm in diameter. It allows Kettle and Kettle 2 barbecues to mount in any direction from the rod holder. Quick disconnect system allows instant installation or storage after use without tools. BLA Code 139646

On Shore Stand Suits both gas and charcoal Kettle barbecues. Cook onshore with this 18-8 stainless steel barbecue stand. It features rubber non-skid foot pads and easily collapses without tools. BLA Code

Base Dia. mm

Height

139648

340

240

N.B. Not recommended for use aboard boats.

Pictured with disposable gas cylinder (not included)

www.bla.com.au

219

section

PUMPS, PLUMBING & GALLEY

Fish and Veggie Grill Tray

Marine Cuisine Barbecue Cookbook

Made from marine grade 304 stainless steel. Sized to fit atop the wire grill of Magma kettle barbecues. This grilling accessory keeps delicate fish, vegetables and small food items from falling through. May also be used with the wok as a steamer tray. Removable rubber coated handle makes the grill tray easy to clean and compact to stow.

From chicken to great hamburgers, this book contains 130 pages of easily prepared barbecue delights, useful recommendations, techniques, hints and accessory ideas for a better grilling experience. Recipes are designed to use a minimum of ingredients and are exclusively prepared for the 'Marine Kettle'® barbecue. BLA Code 139656

Magma Control Valve

BLA Code 139628

Diameter mm 350

Magma Control Valve

- Coleman®

Control valve that provides for direct connection of Coleman® disposable propane cylinders to Magma barbecues with Turbo Venturi.

- LPG

Replacement control valves for Magma barbecues connected to pre regulated LPG. Valves are preset at low, medium or high volume to suit specific Magma barbecue models. The 139630 valve suits all gas Kettle barbecues fitted with the new Turbo Venturi tube. For replacement of control valve on older kettle barbecues, the Venturi tube will also need to be replaced with the new Turbo Venturi tube 139754. Current model control valves can be identified by their Nickel plated Venturi Connection. Specific valves for Gourmet barbecues are detailed in the table below. All these control valves can be connected to gas hoses 139830 and 139832.

Current model nickel plated

Printed markings on valve indicate • No paint - low output • Green - medium output • Yellow - high output

BLA Suits Code 139599 139625 139629

Output Volume

Monterey High Catalina Medium Gas Kettles and Newport Low

BLA Suits BBQ’s Code

Output Colour Volume Marking

139630 139610, 139619, 139621 & 139594 Low None 139631 139590 Medium Green 139633 139586 High Yellow

Radiant Plate to suit Kettle Original

Gas Regulators and Hoses

A time tested, highly efficient radiant plate designed to provide quick and even heat distribution. In conjunction with Magma’s kettle design the radiant plate helps to create efficient convection heating to achieve hot, even temperatures while using a minimum of fuel.

Gas regulators and hoses to connect Magma LPG gas barbecues with gas bottles. The 139824 suits 3/8" left hand threads. The 139826 regulator suits larger gas bottles with POL thread. 139824

139826

139830

BLA Code 139759

220

Quality marine equipment

BLA Code

Description

139824 139826 139830 139832

Gas regulator - 3/8" (l/h inlet) Gas regulator - (pol inlet) Gas hose - 900mm (3/8" BSPM x 1/4" BSPF) Gas hose - 1200mm (3/8" BSPM x 1/4" BSPF)

section

Econo Mate

- Bait and Fillet Board

BLA Code 139670

Front Width To Back mm mm 410

305

Mount Base mm

Mount Screws mm

100x47

4 c/s

Deck Socket Mount

Levelock Rod Holder Mount

Used in conjunction with single mount tables and Newport barbecue. 18-8 stainless steel post and table bracket and deck socket. Stainless steel table to mount bracket fastenings included. Only two positions of rotation.

Used in conjunction with single mount tables and Newport barbecue. Manufactured from heat treated stainless steel and hard anodised aluminium. The quick release cam action design allows convenient all angle adjustment. The 38mm 18-8 stainless steel tube fits into most 'cross pin' type rod holders, in eight different rotational positions. Folds flat for compact storage.

BLA Code 139676

Base Dia. mm

Overall Mount Height Holes mm mm

6 c/s

Locking Flush Socket Deck Mount For use with single mount tables and Newport barbecues. This flush socket set features a push button locking pin and includes a flanged gasket with attached water seal plug. Screws for attachment to table or barbecue included.

BLA Code 139678

Overall Tube Length Length mm mm 350

275

Rail Mount Kits

BLA Code 139680

Deck Flange mm

Cut Out mm

Intrusion

PUMPS, PLUMBING & GALLEY

Folds completely flat when not in use, and is detachable as well! Push/pull stainless steel pin attaches table to the boat, fitting in seconds for a really secure and easy to use bait or fillet board. U.V. stabilised polyethylene construction for quick cleaning, easy on the knife and hygienic in use. Fittings are polished stainless steel. Mount bracket included.

- Single

For use with single mount tables and Newport barbecues. They attach to horizontal round rails and feature two way angle adjustment for perfect horizontal levelling. Made of 18-8 stainless steel and 356 anodised aluminium, they quickly detach without tools for compact storage leaving no hardware on the rails. Great for mounting other items such as solar panels, fish finders or just about anything else onto horizontal or vertical round rails. Sold individually.

Square Rail/Side Mount These all 18-8 stainless steel mounts attach to flat surfaces such as bulkheads, coamings, transoms or cabin sides. Also mounts to square and flat rails. Fits horizontal rails up to 57mm high by any depth or vertical rails up to 41mm wide by any depth. For use with single mount tables and Newport barbecue. BLA Rail Code Diameter mm in BLA Code

Mount Base mm

139694 69x79

Overall Height mm 110

139684 139686

N.B. 22mm and 28mm plastic rail size adaptors are not suitable for use with Newport barbecue. For 22mm rail fitment of Newport barbecue use dual mount kit.

22 - 25 7/8 - 1 28 - 32 11/8 - 1Âź

139778 Spare lever and washer 139780 22-25mm (7/8"-1") adaptor sleeve

www.bla.com.au

221

section

PUMPS, PLUMBING & GALLEY

First Mate Table - Dual Mount Magma’s 'First Mate' dual-mounting cutting and food serving table is a perfect compliment to a Magma barbecue grill. The heavy-duty mount design provides the strength of a work bench with the convenience of Magma’s quick mount system for compact storage. Features large water drainage slots, two knife holders, a handy receptacle for implements and 100mm high side and back guard rails. All edges and corners are rounded for your safety. Virtually indestructible, it does not absorb fish odour, will not crack or mildew and is maintenance free. Made from FDA approved U.V. stabilised high-density polyethylene, it is perfect for preparing and serving food and beverages. Mount kits sold separately. BLA Code 139668

Length mm

Width mm

Height mm

1040

320

115

Pictured with dual flush mount deck socket kit (not included).

Serving Cutting Table - Single Mount The versatile design and premium quality material of the serving cutting table allows it to be used for a wide variety of tasks from food or cocktail service to preparation of bait or cleaning the catch of the day. Incorporates two knife holders and a handy receptacle for implements. The slot at the back of the table permits drainage from the work surface for cleaning. Virtually indestructible, it does not absorb fish odour, will not crack or mildew and is maintenance free. Made from the finest commercial cutting board material, U.V. stabilised high-density polyethylene. All edges and corners are rounded for your safety. Mount kit sold separately. BLA Code

Depth mm

Width mm

Height mm

139660 325 510 75 Mount Kits: 139676 Deck socket mount kit - page 221 139678 Rod holder mount kit - page 221 139680 Locking flush deck socket kit - page 221 139684 Rail mount kit suits 22 - 25mm tube - page 221 139686 Rail mount kit suits 28 - 32mm tube - page 221 139694 Square rail/side mount - page 221

Pictured with Levelock rod holder mount (not included)

Locking Flush Socket Deck Mount Kit

Table Height Extension Kit

Mirror polished 18-8 stainless steel construction. These flush socket sets feature a push button locking pin and include flange gasket with attached water seal plugs. Screws for attachment to table or barbecue included. For use with dual mount tables and Gourmet Series barbecues.

Raises the first mate table by 305mm to a convenient height. 18-8 stainless steel construction. Sold as a set of two. Suitable for use with 139673 dual flush mount deck socket. Can also be used with 139682 dual locking flush socket deck mount, but the locking feature is not available.

BLA Code 139682

Deck Flange mm

Cut Out mm

Intrusion

BLA Code 139675

Rail Mount Kit

- Dual

For use with dual mount tables, and Gourmet series barbecues. These incredibly strong rail mounts have a unique pivoting design which allows them to mount on a straight or curved rail or across the corner of a stern rail. Made of 18-8 stainless steel and 356 anodised aluminium, they easily detach without tools for compact storage.

BLA Rail Code Diameter mm in 139688 22 - 25 7/8 - 1 139690 28 - 32 11/8-1¼ 139778 Spare lever & washer 139780 22-25mm (7/8"-1") adaptor sleeve

222

Quality marine equipment

Square Rail/Side Mount Kit These all 18-8 stainless steel mounts attach to flat surfaces such as bulkheads, coamings, transoms or cabin sides. Also mounts to square and flat rails. Fits horizontal rails up to 57mm high by any depth or vertical rails up to 41mm wide by any depth. For use with dual mount tables and Gourmet Series barbecues.

T10-580/585 "DM" Table

BLA Code

Mount Base mm

139696 69x79

Overall Height mm 110