3 minute read
Mounting instruction
4.2 Operation Instruction for CP86100 4.2.1 Two ways of operation: • Operate manually: Insert the handle tube (50) into the handle sockets. 2 handle sockets are provided. The upper one(P31) is for high pressure and low speed; and the lower one(P43) is for low pressure and faster speed. Fig.12. • Operate by air: Depress the air foot valve(61,Fig.08) 4.2.2 Piston‘s retraction and Extension • 3 positions for the handle lever of selector valve: When it is in position 1, the piston rod is retracting;When it is in position 2, the piston rod is stopping moving;When it is in position 3, the piston rod is extending. Fig.13 4.2.3 Operation • Turn the handle lever (99) to position 3, then depress the air foot valve (P54), and the piston rod will extend quickly.Warning:NEVER operate manually (Manual Low Pressure) simultaneously. • When the serrated saddle gets close to the work piece, change to manual operation. • Adjust the position of work piece to make sure the work piece and piston rod are aligned properly. • Start to press the work piece. Insert the handle tube into the high pressure socket (P31) and pump the handle tube, the piston rod extends slowly and press the work piece. Operator can press by air ,or press by air and manually simultaneously. • Release the pressure: turn the handle lever (99) to position 2, the pressure on the piston rod will release automatically. • Retraction of pistion rod:turn the handle lever (99) to position 1, operate by air or manual.NEVER operate manually (Manual Low Pressure) at the same time. • When complete, disconnect the air hose from the compressor and clean the machine.
WARNING Do not exceed the working load limit / rated capacity of the dolly.
WARNING Make sure that the operator must wear protective cloth, gloves, safety helmet, shoes and ear protector during operating.
WARNING To avoid accidents, always be aware of any on-going work on the machine. Also, always stay focused on the job to be done.
WARNING The product and its accessories must not be modified.
5. Maintenance instruction
Do not use damaged/deformed product. If abnormal noise or vibration occurs, stop use immediately, then inspect and ask manufacturer for help.It is recommended that this inspection be made by a manufacturer’s or supplier’s authorized repair facility. The greatest single cause of failure in hydraulic units is dirt. Keep the service jack clean and well lubricated to prevent
foreign matter from entering the system. If the jack has been exposed to rain, snow, sand, or grit, it must be cleaned before it is used. Store the jack, with pistons completely retracted, in a well-protected area where it will not be exposed to corrosive vapors, abrasive dust, or any other harmful elements. Periodically check the condition of the product. Store the product in dry and non-corrosion environment. Owners and/or operators should be aware that repair of this equipment may require specialized knowledge and facilities. It is recommended that an annual inspection of the product be made by a manufacturer’s or supplier’s authorized repair facility and that any defective parts, decals, or safety labels or signs be replaced with manufacturer’s or supplier’s specified parts. A list of authorized repair facilities is available from the manufacturer or supplier, please call them for help. Any product that appears to be damaged in any way, is found to be worn, or operates abnormally SHALL BE REMOVED FROM SERVICE UNTIL
REPAIRED. It is recommended that necessary repairs be made by a manufacturer’s or supplier’s authorized repair facility if repairs are permitted by the manufacturer or supplier. Only attachments and/or adapters supplied by the manufacturer shall be used.
Original Instructions are in English. Other languages are a translation of the original instructions.
The design has been validated according to: ASME ASP-2010
7. Declaration of conformity
We : CHICAGO PNEUMATIC Tool Co. LLC, 1815 Clubhouse Road, Rock Hill, SC 29730 - USA
Declare that the product(s): CP86750/CP86100 Serial: 00001 to 99999
Machine type(s): Hydraulic press Origin of the product: China is in conformity with the requirements of the council Directives on the approximation of the laws of the Member States relating : to “Machinery“
2006/42/EC (17/05/2006)
applicable harmonised standard(s) : EN 13736 : 2003 + A1 : 2009 Name and position of issuer: Pascal Roussy (R&D Manager) Place & Date: Saint-Herblain, 10/04/2020
Technical file available from EU headquarter. Nicolas Lebreton R&D manager CP Technocenter 38, rue Bobby Sands - BP10273 44800 Saint Herblain - France
