GatesIndustrialHoseCatalog by Canyon Fleet Outfitters

2009 GATES INDUSTRIAL HOSE, COUPLINGS & EQUIPMENT

The Worldâ&#x20AC;&#x2122;s Most Trusted Name in Belts, Hose and Hydraulics.

Your Local Distributor:

Gates Corporation 1551 Wewatta Street | P.O. Box 5887 | Denver, CO 80217-5887 (800) 366-3128 | Fax (303) 744-4499 www.gates.com/industrialhose

39496-000 October 2009

Hose, Couplings & Equipment

WARNING Gates Corporation recommends Industrial hoses for normal service as described in this catalog. Other applications should be referred to your respective marketing representative. In any application, there may be inherent risk of bodily injury or property damage and the user is responsible for implementation of adequate safety precautions. It is the responsibility of the person supplying the hose to advise the user of proper instructions for the adequate safe use and/or precautions and to warn the user of consequences of failure to heed such instruction. Should a hose assembly fail during use because of excessive pressure, injurious and/or damaging chemicals, elevated temperature materials, explosives or flammable materials, then serious bodily injury or destruction of property could result from impelled couplings, whipping hose, high pressure or high velocity discharge, chemical contact, high temperature materials, explosion or fire. In known high risk areas, it is recommended that hose inspections be performed at frequent intervals related to the risk factor. Hose with obvious damage should be scrapped and replaced. These inspections should include tube and cover conditions, leaking or slipped couplings and proof test. Detailed information concerning storage, care and maintenance may be found in the Hose Handbook published by The Rubber Manufacturers' Association, 1901 Pennsylvania Avenue, N.W., Washington, D.C. 20006 and in SAE Recommended Practices J1273. IMPORTANT Gates recommends only those applications of products specified in Gates product literature. Gates disclaims any liability for use of its products in applications other than those for which they were designed.

Service Life All rubber products, including Industrial Hose assemblies, have a limited life on a given application. Assuming the correct hose has been selected for the application, this service life can be adversely affected by many variable conditions. The major ones are: — Exposure to severe external abuse such as kinking, bending, high end pull, crushing or abrasion. — Exposure to higher-than-rated working pressures or to high surge pressures. — Exposure to higher-than rated temperatures. — Misapplication or exposure to corrosive liquids or gases outside the range of suitable applications. 1.

External abuse—hoses should be placed where they will not be run over by equipment or subjected to high end pull. Hoses should not be bent below recommended minimum bend radius. This could result in kinking the hose or reducing its pressure resistance. Large diameter hoses also may require additional support to reduce external abuse. Hose & System Pressures—In establishing and determining pressures related to hose and the systems to which they are applied, it is necessary to consider separately the characteristics of the hose and the system. — The system (or device or application) can have several pressures depending on pressure sources and surges imposed by the operator or mechanical components. — A given hose has a fixed characteristic with respect to the pressure it can withstand (and how it is applied) and still give satisfactory life.

High Temperatures—The allowable temperature ranges for industrial hoses are shown on Page 6. These are for product temperatures and should not be exceeded. High temperatures can degrade rubber stocks very quickly resulting in short service life. Where external temperatures are higher than normal ambient, contact your Gates field representative for recommendations.

Misapplication—All industrial hoses are designed for a certain specific application or related application. They should not be used for any other applications.

Hose Information—Refer to the following pages for details of hose construction and physical characteristics. These are shown in the data pages and include such items as rated working pressure, vacuum rating, minimum bend radius and static conductivity ratings.

Internal Abrasion—For applications of a highly abrasive nature where the hose makes one or more bends, hose should be rotated 90º periodically to lengthen service life.

The hose manufacturer established, through design and testing, the recommended rated working pressure for the hose. It is the responsibility of the user to accurately determine the system pressure. Steady state pressure can be measured readily by gauges. Surges are difficult to measure and may require the use of electronic pressure pickup devices. Also, surge values depend on so many variables that a series of tests are usually required to obtain a valid set of readings. However, if there are extreme surges in the normal operation, or if there is the likelihood of abnormal operation of the system, the magnitude must be determined. Considering the recommended rated working pressure of the HOSE and the various pressures of the SYSTEM, the hose is matched to the system using proper application engineering principles. WARRANTY

GATES CORPORATION LIMITED WARRANTY

The Gates Corporation (“Gates”) product is warranted to be free from defects in material or workmanship for twenty-four (24) months from the date of delivery to Customer. Gates will, at its option, replace or repair any merchandise proved defective in material or workmanship, or both. In no event will Gates honor any warranty claim unless it is notified of the claim within six (6) months of the expiration of the warranty period. This shall be the sole remedy for breach of warranty.

This is the exclusive remedy, limited to the Customer’s purchase price of the product. Damage to the product due to abuse, misuse, improper use, inadequate maintenance, or failure to follow published installation, use and service recommendations automatically voids this warranty. For warranty service, please contact the Customer Service Department of Gates Corporation, 1551 Wewatta Street, Denver, Colorado 80202. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY DISCLAIMED. IN NO EVENT WILL GATES BE LIABLE TO ANY PARTY FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL, EXEMPLARY AND INDIRECT DAMAGES, INCLUDING BUT NOT LIMITED TO LOST PROFITS, REGARDLESS OF WHETHER SUCH DAMAGES WERE REASONABLY FORESEEABLE, OR WHETHER GATES HAD KNOWLEDGE THAT THEY COULD OCCUR. Some states do not allow the exclusion or limitation of incidental or consequential damages, and some states do not allow limitations on how long an implied warranty lasts, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Printed in U.S. of America

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Table of Contents Description

Page

Warranty..............................................................................................................................................................................Inside Front Cover Warning ...............................................................................................................................................................................Inside Front Cover Service Life.........................................................................................................................................................................Inside Front Cover Index by Specification.....................................................................................................................................................................................2 Index of Industrial Hoses by Name and Number.......................................................................................................................................3-4 Index of Industrial Hoses by Application ...................................................................................................................................................5-6 Hose Temperature Ranges...............................................................................................................................................................................7 Selection of Hoses and Couplings ..................................................................................................................................................................8 Ends for Gates Hoses ......................................................................................................................................................................................9 Industrial Hose Categories: Acid-Chemical Hose .......................................................................................................................................................................10-19 Air and Multi-Purpose Hose ..........................................................................................................................................................20-37 Food and Beverage Hose ................................................................................................................................................................38-50 Marine Hose ....................................................................................................................................................................................51-66 Material Handling Hose ..................................................................................................................................................................67-73 Mining Hose ....................................................................................................................................................................................74-79 Oilfield Hose ...................................................................................................................................................................................80-96 Petroleum Transfer Hose ..............................................................................................................................................................97-114 Pressure Washer ..........................................................................................................................................................................115-119 Steam Hose .................................................................................................................................................................................120-123 Water Hose ..................................................................................................................................................................................124-131 Crimper ................................................................................................................................................................................................132 Clamps .........................................................................................................................................................................................133-134 Hose Couplings ...........................................................................................................................................................................135-139 Coupling Information...........................................................................................................................................................................140-149 RMA Definitions, Abbreviations and Tolerances................................................................................................................................150-151 Hose Maintenance, Cleaning and Storage...........................................................................................................................................152-154 Industrial Hose Finder..........................................................................................................................................................................155-174 Characteristics of Hose Stock Types ...................................................................................................................................................175-178 Chemical Resistance Table ..................................................................................................................................................................179-207

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The worldâ&#x20AC;&#x2122;s most trusted name in belts, hose and hydraulics.

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

TERMS, CONDITIONS AND TRANSPORTATION POLICY TERMS POLICY As shown on applicable discount schedule. Conditions • Prices do not include charges for special packaging, which will be extra, unless otherwise specified. • Prices are subject to change without notice. • Buyer shall reimburse Seller for all taxes, excise or other charges. Seller may be required to pay to any government (Federal, State or local) upon the sales, use, production or transportation of the merchandise sold hereunder. • Seller shall be excused and not liable for delays caused by Buyer’s request, labor troubles, shortages in materials, damage to plant, government regulations or other cause, similar or otherwise beyond Seller’s control.

TRANSPORTATION POLICY All prices are F.O.B point of shipment. The “F.O.B. point of shipment” term means that the title to the goods passes to the consignee (customer) at time of shipment and any claims against the carrier for loss or damage become the responsibility of the consignee. • Freight terms: As shown on applicable discount schedule. F.O.B. point of shipment, and shipped to any one location served by common carrier within the Continental United States, Hawaii or Alaska. On shipments to Hawaii or Alaska, shipment by sea service is considered common carrier. • Industrial Hose Products must be shipped to the location issuing the purchase order. • Nonstock or special manufactured items will stand on their own for freight allowance, F.O.B. point of manufacture. • Partial shipments made at Gates discretion will be shipped prepaid provided the original order qualified for prepaid shipment.

Index by Specification SPEC

PAGE

3129F, 3129H, 3129L............................67 3131 ......................................................42 3132C ....................................................39 3132C/3132H ........................................38 3132D ....................................................46 3132LW .................................................40 3132P ....................................................43 3133 ......................................................41 3135SP................................................126 3137M .................................................127 3137ME .................................................57 3137T ..................................................128 3150B ..................................................107 3200R/3200B.........................................27 3202T/3202TW......................................22 3204BL, GR, YL ....................................31 3204E ....................................................29 3204E/3204S.........................................28 3204EB/3204SB ....................................30 3205R ....................................................25 3206 ......................................................26 3207NN/3207T ......................................19 3213B/3325T .......................................119 3217HY................................................118 3219AB..................................................21 3219AR .................................................20 3220E ..................................................113 3220LP, 3320 .......................................111 3220SP ................................................112 3221FR ................................................110 3222B, G, R, Y, BK, GY........................24 3237A ....................................................36

SPEC

PAGE

3284D, E, G, H, R, Y ............................23 3333 ......................................................37 3602EL ................................................121 3603PW ...............................................117 3605 ....................................................120 3618/3618GL.........................................78 3618/3618Y ...........................................79 3618HT..................................................77 3618MT .................................................76 3619G/3619GL ......................................33 3619M ...................................................74 3619MC/3619MY...................................75 3624.....................................................114 3658F ....................................................60 3670H, 4651RL, ZL...............................95 4040A ....................................................66 4110DW...............................................102 4110SH................................................103 4110SS ................................................105 4129A ....................................................71 4169A ....................................................53 4171 ......................................................55 4175EC .................................................51 4176HD .................................................52 4219G....................................................63 4219M ...................................................61 4219N ....................................................62 4230T ....................................................56 4465 .................................................17-18 4651ZL, XL............................................96 4657, KB, KG, KK, KY, PB, PG, PY ...115 4657F, XB, XG, XY..............................116

SPEC

PAGE

4663A ....................................................34 4663J.....................................................35 4663K ....................................................65 4684CF..................................................59 4685WG ................................................54 4686AR/4686DC .................................124 4686AT ................................................125 4686ME .................................................58 4687R ..................................................100 4688AC, AF ...........................................98 4688CC/4688DC ...................................97 4688CN .................................................99 4688SH ...............................................104 4688SS................................................106 4688V ..................................................101 4689M ...................................................64 4691HA/4691HC ...................................69 4691L ....................................................68 4691V ....................................................70 4693B ....................................................44 4693R ....................................................45 4695/4695G...........................................12 4695M ...................................................13 4695RG .................................................14 4696A ....................................................16 4697G....................................................15 4698B ....................................................10 4698MB .................................................11 7408 ....................................................133 7422 ....................................................134 7744 .......47-50, 72-73, 108-109, 129-131 7746 Silicone Free ................................32

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Index of Industrial Hose by Name and Number NAME

PAGE

1000 MP/Mine Spray ...............74 119B Plant Master® ..................21 16 EFBOP Blow-Out Preventer ...............................96 163SB (Air & Vapor Duct Heavy Duty) ...........................35 18MB Air Drill ...........................78 19B Plant Master® ....................20 205MB Steam King® ..............120 232MB Steam Queen® ...........121 319MB Gold Master® ...............33 33HB (Divers’ Air) ....................37 4219G (Fuel Line & Tank Vent).......................................63 429W (Sand Blast)...................71 4663K (Fuel Fill - Corrugated).65 4684CF (Wet Exhaust Corrugated)............................59 500 MP Air Drill........................79 609W (Dry Cement Delivery)...67 610W (Bulk Commodity)..........46 63SB (Air & Vapor Duct)..........34 688SB (Bulk Commodity) ........68 690SB (Bulk Commodity) ........44 692SB (Bulk Commodity) ........45 6B Dura Master® ......................26 75W (Standard Wall Coolant) ..51 76W (Heavy Wall Coolant) ......52 770SB ......................................70 77B (Paint Spray and Chemical)...............................19 Adapta Flex™ Black ..................30 Adapta Flex™ Blue, Green & Yellow Cover ..........................31 Adapta Flex™ Red ....................28 Adapta Flex™ Red Cover - UPS Shippable Reels.....................29 Appaloosa® ...............................14 Aquarius® Potable Water..........43 Barracuda® .............................125 Blacksnake® (Curb Pump Hardwall) ..............................114 Blender Transfer ....................102 C5M Fuel Line .........................60 Cellar Master® ..........................39

NAME

PAGE

Cellar Master® Light .................40 Colt® .........................................16 Creamery/Paper Mill Washdown............................119 Cyclone® .................................118 Dolphin®..................................128 Duro Flex® ................................27 Engine Coolant (Oil Resistant Softwall) .................................53 Engine Coolant (Silicone) ........55 Engine Coolant (Wire Inserted Hardwall)................................54 Food Master® Lite™ ...................41 Food & Beverage Master® .......38 Fuel Fill (USCG Type A1 and B1) .........................................64 Fuel Line (USCG Type A1)......61 Fuel Line (USCG Type B)........62 Fuel Oil Delivery.....................110 GLX® - Female JIC 37° Flare Swivel...................................138 GLX® - FP Female NPTF Swivel...................................137 GLX® - FPX Female NPSM Swivel...................................137 GLX® - FSX 45° SAE Female Swivel...................................136 GLX® - Male Pipe (NPTF 30° Cone Seat)...........................135 GLX® - MPX Male NPTF Swivel...................................136 GLX® - MS 45° SAE Male Solid .....................................135 GSH™ - GSH with Intergral 2″ Fig. 1502 Hammer Unions ..138 Heater Hose.............................56 Heavy-Duty T-Bolt Clamps ....134 Hot Air Blower ..........................69 LOL Plus (Lock-On Hose) .......23 Longhorn®.................................97 Longhorn® AF (Alternative Fuel-Corrugated)....................98 Longwall Mine Emulsion ..........75 LP350 (Butane-Propane) .......111 LP350X (Butane-Propane).....112

NAME

PAGE

LPG Vapor..............................113 Marlin® ....................................127 Master-Flex® 100GR ..............130 Master-Flex® 101CL ...............131 Master-Flex® 200CL .................47 Master-Flex® 201CR ................48 Master-Flex® 202SW................49 Master-Flex® 300 EPDM ..........72 Master-Flex® 400......................73 Master-Flex® 500....................129 Master-Flex® Fuel Delivery ....108 Master-Flex® Vapor Recovery..............................109 Maverick™ ...............................100 Mustang® ..................................12 Mustang® Crush Resistant .......13 Ohmega® (Pot Room) ..............36 Powerbraid® Plus (Slim Hole Rotary) ...................................95 PowerClean™ - 1 Wire Braid ..115 PowerClean™ - 2 Wire Braid ..116 Premo Flex® .............................25 Pressure Washer Assemblies...........................117 Python® Plus (Lock-On Hose)..24 Renegade™ ...............................15 Sani-Pure™ ...............................42 Scorpion™ .................................76 Scorpion™ X-Treme ..................77 Sea Horse® 400 (Fuel Transfer)...............................103 Sea Horse® 400 HW (Fuel Transfer Suction/Discharge Hardwall)..............................104 Sea Horse® (Fuel Transfer)....105 Sea Horse® HW (Fuel Transfer Suction/Discharge Hardwall)..............................106 Shark® ....................................124 Stainless Steel Clamps..........133 Stallion® ....................................10 Stallion® Crush Resistant .........11 Steelhead®..............................126 Steer® .......................................99 Super-Vac® .............................101

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics.

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Terminator® ...............................22 Thermo AG® 570 (Ag Spray) ...17 Thermo AG® 800 (Ag Spray) ...18

Trident® 400............................107 Tufflex® Food ............................50 Tufflex® Plus .............................32

Vacuum Tubing ........................66 Wet Exhaust (Hardwall) ...........58 Wet Exhaust (Softwall) ............57

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Index of Industrial Hose by Application Subject

Page

Subject

Page

ABS ..................................................................60 Acid-Chemical .............................................10-19 Acid-Suction ................................................10-19 Agricultural Spray........................................17-18 Agricultural Water....................................124-131 Air .........................................20-37, 74-75, 78-79 Air Blower .......................................34-35, 70, 73 Air Drill.........................................................78-79 Air Duct ...........................................34-35, 70, 73 Air Tools................................20-21, 25-33, 74-75 Ammonia Applicator ....................................28-32 Aromatic Gasolines ..97-100, 103-106, 108, 110, 114 Automotive Coolant.....................................51-52

FDA (U.S. Food & Drug Administration) ....38-42, 44-50 Fertilizer Transfer ...........17-18, 20-21, 25-32, 72 Food Handling .................................38-42, 44-50 Fuel Feed, Filler ..........................................60-62 Fuel Oil Transfer .......................97-100, 108, 110 Fuel Transfer ......................97-101, 103-110, 114

B Beverage..........................................38-42, 44-50 Breathing.........................................20-21, 25, 37 Brewery .......................................................38-40 Bulk Materials.......................38-42, 44-49, 67-73 Butane......................................................111-113

C Cement........................................................67-68 Chemical Cleanup.................................10-16, 19 Cleanup ..............................21, 115-116, 118-119 Compressed Air ..............................20-33, 74, 79 Coolant..................................................51-55, 59 Couplings ................................................135-139 Creamery Washdown .....................................119 Cross-Linked Polyethylene .........................10-14 Curb Pump (UL-330) ..............................110, 114

D Debris Collecting.............................68, 70, 72-73 Distillate Transfer .......................97-100, 108-109 Divers’ Air .........................................................37 Dust Collection ..........................34-35, 70, 72-73

E Edible Products Transfer .................38-42, 44-50 Electric Resistance Ends................20-22, 24, 36 Engine Coolant .....................................51-55, 59 Exhaust .......................................................57-59

G Gasohol ..........................................................114 Gasoline Pump (UL-330)................................114 Gasoline Transfer ......97-100, 103-108, 110, 114 Gatron® ........................................................12-14 General Purpose (See Air & Multi-Purpose) ....................20-37, 74-75, 78-79 Grain Handling................................44-49, 68, 73 Grass Vacuuming.......................................70, 73

H Heavy-Duty Water...........................124, 126-127 Herbicide Transfer .......................17-18, 130-131 High Pressure Air............................33, 74, 78-79 High Pressure Washer ............................115-119 High Pressure Water ...............................115-118 Hot Air Blower ..................................................69

I Industrial Air..........................20-35, 74-75, 78-79 Industrial Couplings.................................135-139 Industrial Steam ......................................120-121 Industrial Water ....20-33, 51-52, 74-75, 118-119, 124-131 Insecticide Transfer......................17-18, 130-131 Insulation Handling.....................................70, 73

L Lay Flat Hose .................................................129 Leaf Collector .............................................70, 73 Lightweight Water .....................51, 125, 128-131 LP Gas (UL-21)........................................111-112 LPG Vapor ......................................................113 Lube Oil Transfer ...........................20-23, 97-100

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics.

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Subject

Page

Subject

Page

Marine Wet Exhaust .............................51, 57-59 Material Handling ........................................67-73 Mining .............................................22, 74-75, 79 MSHA (Mining Safety & Health Admin.) .........22, 74-75, 79 Multi-Purpose .......................20-37, 74-75, 78-79

Tank Truck (Chemical) ................................10-16 Tank Truck (Food)............................38-42, 44-49 Tank Truck (Petroleum)..............97-101, 103-110 Three A (3A Standards).......38-39, 41-42, 45, 47

N Natural Gas..............................................111-112 Non-Conductive .........................20-22, 24-25, 36 Nylon ................................................................19

U Underwritersâ&#x20AC;&#x2122; Laboratories (UL)...............111-114 USCG....................................................60-62, 64 USDA .............................38-39, 41-42, 45, 47-50

V Vacuum (Dry) ..............................................72-73 Ventilating .................................34-35, 63, 70, 73

O Oxygen............................................20-21, 25, 37

P Paint Spray.......................................................19 Paper Mill Washown.......................................119 Pesticides.....................................17-18, 130-131 Petroleum ..................................................97-114 Pneumatic Applications ........20-33, 74-75, 78-79 Pot Room...................................20-22, 24-25, 36 Potable Water.......................38-42, 44-45, 47-50 Propane (UL-21) ......................................111-112

Washdown..............................20-21, 74, 115-119 Water .......................................................124-131 Water Discharge ..................51-52, 126-129, 131 Water Suction .....72, 115-119, 124-125, 130-131 Water Suction & Discharge ..............72, 115-119, 124-125, 130-131 Wet Exhaust ....................................51-52, 57-59 Wine ............................................................38-40

R Refueling.........................................................114 Resistance, Electrical ................20-22, 24-25, 36 RMA (Rubber Manufactures Association)..20-31, 51-53, 59-60, 65, 72-73, 121

S SAE 20R, 30R ...........................51-56, 59-60, 63 Sand Blast ........................................................71 Sewage.............................................................72 Sludge ......................................................68, 101 Solvents ..........................................10-16, 19, 72 Steam ......................................................120-121

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Hose Temperature Ranges

Temperature ranges for the industrial hoses are shown by application groups. The range in the Normal Service column indicates the usual temperature range for each specific hose listed under each application group. The lower limit column indicates the approximate temperature at which the hose will become too stiff to use. For information on applications or temperatures not listed in this table, contact Denver Production Application.

Application Group Acid-Chemical 77B Appaloosa® Colt® Mustang® ™ Renegade Stallion® ® Thermo-Ag 570 Thermo-Ag 800 Air & Multi-Purpose 6B 18MB 19B/119B 33HB (Divers Air) 63SB 163SB 319MB (Gold Master®) 500 MP/Air Drill 1000 MP/Mine Spray ® Duro Flex LOL Plus Longwall Mine Emulsion ® Ohmega ® Premo Flex ® Python Plus ® Terminator ® Tufflex Plus Food & Beverage 610W 690SB 692SB Brew Master® Cellar Master® Cellar Master Light Food and Beverage Master® ™ Food Master® Lite ® Master Flex 200CL Master Flex 201CR Master Flex 202SW ™ Sani-Pure Tufflex® Food Marine 75W (Standard Wall Coolant) 76W (Heavy Wall Coolant) 4219G (Fuel Line & Tank Vent) 4663K (Fuel Tank Filler) 4684CF (Wet Exhaust) C5M (Fuel Line) Engine Coolant (Softwall) Engine Coolant (Hardwall) Engine Coolant (Silicone) Fuel Fill (USCG Type A2&B2) Fuel Line (USCG Type A1) Fuel Line (USCG Type B) Heater Hose Vacuum Tubing Wet Exhaust (Softwall) Wet Exhaust (Hardwall) Material Handling 429W 609W 688SB

Range for Normal Service F* †

Lower Limit F

0-125 † 0-125 † 0-125 † 0-125 † 0-125 † 0-125 0-130 0-130

-40 -40 -40 -40 -40 -40 -10 -10

0-200** 0-212 0-212** 0-120 0-250 0-250 0-212 0-180 0-212 0-200** 0-212 0-212 0-150 0-212** 0-212 0-212 0-150

-40 -30 -40*** -40 -30 -30 -40 -22 -40 -40 -40 -40 -20 -40 -20 -40 -15

0-150 0-150 0-180 0-230 0-230 0-212 0-230 0-230 10-130 10-130 10-130 0-230 10-130

-40 -40 -40 -40 -40 -40 -40 -40 -10 -10 -10 -40 -10

32-257 32-257 0-257 0-212 0-212 0-212 0-212 0-257 0-347 0-212 0-212 0-250 0-257 0-257 0-257 0-257

-40 -40 -40 -40 -40 -4 -40 -40 -65 -40 -40 -40 -40 -40 -40 -40

0-150 0-150 0-150

-40 -40 -40

Application Group Material Handling 770SB Hot Air Blower Master Flex 300EPDM Master Flex 400 Oil Field ® Powerbraid Plus ® Black Gold Rotary (Grade D & E) Black Gold Rotary Cementing Black Gold Rotary Cementing Black Gold Rotary Sour Service Black Gold Rotary Choke & Kill Black Gold Rotary Super Choke & Kill Petroleum ® Blacksnake Blender Transfer ® Brahma Fuel Oil Delivery ® Longhorn ® Longhorn AF LP350X LPG Vapor ™ Maverick ® Master Flex Fuel Delivery Master Flex Vapor Recovery ® Sea Horse Sea Horse HW ® Steer ® Super-Vac ® Trident 400 Pressure Washer Creamery/Paper Mill Washdown ® Cyclone ™ PowerClean Pressure Washer Assemblies Steam 205MB 232MB Water ® Barracuda ® Dolphin ® Marlin ® Master Flex 100GR Master Flex 101CL Master Flex 500 ® Shark ® Steelhead

Range for Normal Service F*

Lower Limit F

0-150 0-350 10-140 32-140

-40 -40 -30 -30

0-180 0-180 0-180 0-212 0-200 0-200 0-200

-40 -4 -4 -4 -4 -4 -4

0-120 0-180 0-180 0-180 0-180 0-180 0-180 0-150 0-180 0-130 0-140 0-180 0-180 0-180 0-150 0-158

-40 -40 -40 -40*** -40 -30 -40*** -30 -40 -30 -30 -40 -40 -40 -40 -30

0-212 0-212 0-250 0-250

-40 -40 -40 -40 1

0-450 1 0-450 0-180 0-180 0-180 10-130 10-130 25-120 0-180 0-150

-40 -40 -40 -40 -40 -10 -10 +25 -40 -40

‡

As temperature increases, allowable pressure rating decreases. For details, see the rated working pressure/temperature tables listed with the individual hose specifications. † Contact Denver Product Application for chemicals over 125ºF. 1 With saturated or superheated steam. 2 With saturated steam only. * Ambient or product temperature. ** If hose is subjected to this temperature continuously, reduce the catalog rated working pressure by 30%, or use interlocking type couplings. *** These hoses will be flexible down to -20ºF. At temperatures between -20ºF and -40ºF, the hose may require significant force to be bent, flexed or pulled from reels. SUCTION VALUES ARE AT AMBIENT TEMPERATURES UNLESS OTHERWISE STATED.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics.

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Selection of Hoses and Couplings There are many types of industrial hoses—all designed for a particular application or several related applications. When hoses are mated with the proper couplings and used in the correct application, hose assemblies will give long, trouble-free service. This catalog is designed to make certain that you obtain long service life by: •

Helping you select the proper hose and coupling from among the many types available.

•

Giving you suggestions on how to take reasonable care of the hose assembly and maintain it for maximum service life.

Follow the instructions and procedures given below:

For example: 19. Check coupling compatibility in Industrial Hose Coupling Assembly Guide #39505 with the material to be handled. Provide for proper care and maintenance of the assembly. Certain critical applications require the use of just one specific hose or group of hoses. DO NOT SUBSTITUTE. Critical Application Steam

Select a hose that meets the application requirements from Steam Hose Section only.

LP Gas

LP350/LP350X

Corrosive Chemicals (Acids—Bases)

Selection of Hoses and Couplings Information in this catalog will enable you to select hose and couplings for many applications.

Remember the Word STAMPED To Help You Select the Best Hose

Recommended Gates Hoses

Edible Products

Select a hose that meets the application requirements from Acid-Chemical Hose Section only. Select a hose that meets application requirements from Beverage and Food Hoses. Hose must have FDA tube stock.

Size: Inside diameter, outside diameter, length. Temperature: Minimum and maximum ºF. Application: How and where used: Special needs, UL, Government, FDA, MSHA, etc.

Material Conveyed: Air, water, chemicals (concentration and temperature), petroleum, etc.

Pressure: Maximum rated W.P. (psi) or Suction (In.Hg) Ends: Straight, Male, etc. Delivery: When, where, quantity. Select one of the recommended couplings from the hose coupling information section. In each individual Hose Specification Section, couplings are recommended by a bold number in brackets.

SPECIAL HOSES ARE AVAILABLE Gates can furnish special hoses for specific applications. For information, contact Denver – furnishing complete details of hose application.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Ends for Gates Hose Many applications require hose with special ends to provide protection and better coupling for the hose.

To be sure you receive the proper hose end, always specify the type of end, the length of end and its inside diameter (if enlarged and non-standard).

Four Types of Hose Ends 1. Plain end (When ordering—specify P.E.) Braided, spiral and thermoplastic hoses are available only with plain ends. Plain ends ends. Plain ends are generally furnished on wrapped and horizontal braid hoses, unless braid hoses, unless otherwise specified. The plain end is obtained by merely cutting merely cutting hose to a specified length.

2. Straight End (When ordering—specify S.E.) All wire-reinforced, hand-built hoses are available with straight ends. The straight end, not corrugated, has all construction elements except the wire. Straight ends permit leakproof clamping of the hose because the wire does not overlap the coupling shank.

3. Enlarged End (When ordering—specify E.E.) Hand-built hoses, either wire-reinforced or wrapped, are also available with enlarged ends. The hose end is enlarged to accommodate the O.D. of a nipple and the depth of the shank. Thus, an enlarged end to 6-5/8" I.D. is made to fit a 6" nipple, which has a 6-5/8" O.D.

4. Smooth End (Seldom Used) The smooth end is used on wire reinforced hose with corrugated cover. Construction elements, including wire, extend through to the end of the hose. The outside of the end is smooth with no corrugations.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics.

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Acid-Chemical Hose

Stallion® (Specification 4698B)

Nom. I.D. (In.) 3/4 3/4 1 1 1 1 1/2 1 1/2 1 1/2 2 2 2 1/2 2 1/2 3 3 4 4

(mm) 19.1 19.1 25.4 25.4 25.4 38.1 38.1 38.1 50.8 50.8 63.5 63.5 76.2 76.2 101.6 101.6

Nom. O.D. (In.) 1.29 1.29 1.56 1.56 1.56 2.05 2.05 2.05 2.55 2.55 3.07 3.07 3.59 3.59 4.66 4.66

(mm) 32.8 32.8 39.6 39.6 39.6 52.1 52.1 52.1 64.8 64.8 78.0 78.0 91.2 91.2 118.4 118.4

Max. W.P. (psi) 200 200 200 200 200 200 200 200 200 200 150 150 150 150 125 125

(MPa) 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.03 1.03 1.03 1.03 .86 .86

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762 762 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 4.0 4.0 5.0 5.0 5.0 8.0 8.0 8.0 9.0 9.0 12.0 12.0 18.0 18.0 24.0 24.0

(mm) 102 102 127 127 127 203 203 203 229 229 305 305 457 457 610 610

Wt. Per Ft. (Lbs.) .52 .52 .63 .63 .63 .93 .93 .89 1.18 1.18 1.49 1.49 1.83 1.83 2.74 2.74

(Kg) .24 .24 .29 .29 .29 .42 .42 .42 .54 .54 .68 .68 .83 .83 1.24 1.24

Standard Pack 100 ft. 20 ft. 100 ft. 20 ft. 200 ft. 100 ft. 20 ft. 200 ft. 100 ft. 20 ft. 100 ft. 20 ft. 100 ft. 20 ft. 100 ft. 20 ft.

Stock (X) or Minimum Order Qty. X X X X 400 ft. X X 400 ft. X X X X X X X X

Gates Item No. 4698-0011 4698-0021 4698-0012 4698-0022 4698-0029 4698-0013 4698-0023 4698-0031 4698-0014 4698-0024 4698-0015 4698-0025 4698-0016 4698-0026 4698-0017 4698-0027

RECOMMENDED FOR:

Tank truck, barge, ship, or storage tank transfer of a variety of chemical products. Stallion has a wire helix for full suction capability. The tube stock (Teflon* or Neoflon**) has excellent chemical resistance and is backed by Gates Gatron™ for flex fatigue safety at the coupling. Stallion is designed for easy cleaning in a bath containing 10% (NaOH) @ 212°F (100°C). Cleaning in place (CIP) methods may be used. Applications include most basic chemicals which are building blocks for numerous chemicals used in a variety of industries. Reference Gates Chemical Resistance Table for proper hose selection. Compatible with commercially available Bio-Diesel fuels up to B-100.

TEMPERATURE:

-40°F to +300°F (-40°C to +149°C) normal service. Stallion is designed to withstand fluid temperatures to +300°F (+149°C), however the rating is dependent on the specific chemical conveyed. Contact Denver Product Application (303) 744-5070 for any chemical above +125°F (+52°C).

CONSTRUCTION:

Tube: Reinforcement: Cover:

Type T (FEP) Teflon* or Neoflon**. White. Backed with Gatron™ (Modified XLPE). Synthetic, high tensile textile with steel wire helix. Type P (EPDM). Blue corrugated with red spiral stripe.

COUPLINGS:

Gates has tested hose assemblies at the maximum rated service temperature to assure your safety. Use permanent fittings only 71 or 73 for fluid temperatures up to 300°F (149°C). Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled and wrapped in polyethylene.

BRANDING:

Continuous transfer label. Example: “GATES® Stallion® U.S. Pat. No. 5,647,400 Acid-Chemical Suction/Discharge 200 PSI (1.38MPa) WP Made In U.S.A. For your safety: Use Permanent Fittings Only”

SPECIAL ORDER REQUIREMENTS:

Black, red, green and yellow covers are made to order and require minimum production order quantities of 400 feet per size. For price, add 10% (x1.10) to price. Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details.

REMNANT LENGTHS:

Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. *Teflon® is a Registered Trademark of DuPont. **Neoflon® is a Registered Trademark of Daikin.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 10

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Acid-Chemical Hose

Stallion® Crush Resistant (Specification 4698MB)

Nom. I.D. (In.) 3/4 1 1 1/2 2

(mm) 19.1 25.4 38.1 50.8

Nom. O.D. (In.) 1.33 1.58 2.08 2.58

(mm) 33.8 40.1 52.8 65.5

RECOMMENDED FOR:

TEMPERATURE:

CONSTRUCTION:

Max. W.P. (psi) 200 200 200 200

(MPa) 1.38 1.38 1.38 1.38

Suction (In. Hg) 20.0 20.0 20.0 20.0

(mm Hg) 508 508 508 508

Min. Bend Radius (In.) 4.0 5.0 8.0 9.0

(mm) 102 127 203 229

Wt. Per Ft. (Lbs.) .53 .63 .86 1.09

(Kg) .24 .29 .39 .49

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. 400 ft. X X X

Gates Item No. 4698-0001 4698-0002 4698-0003 4698-0004

Tank truck, barge, ship, or storage tank transfer of a variety of chemical products. Stallion Crush Resistant has a monofilament helix for suction and crush resistant capability. The tube stock (Teflon* or Neoflon**) has excellent chemical resistance and is backed by Gates Gatron™ for flex fatigue safety at the coupling. Stallion Crush Resistant is designed for easy cleaning in a bath containing 10% (NaOH) @ 212°F (100°C). Cleaning in place (CIP) methods may be used. Applications include most basic chemicals which are building blocks for numerous chemicals used in a variety of industries. Reference Gates Chemical Resistance Table for proper hose selection. Compatible with commercially available Bio-Diesel fuels up to B-100. -40°F to +300°F (-40°C to +149°C) normal service. Stallion Crush Resistant is designed to withstand fluid temperatures to 300°F (+149°C), however the rating is dependent on the specific chemical conveyed. Contact Denver Product Application (303) 744-5070 for any chemical above 125°F (+52°C). Tube: Reinforcement: Cover:

Type T (FEP) Teflon* or Neoflon**. White. Backed with Gatron™ (Modified XLPE). Synthetic, high tensile textile with monofilament helix and static wire. Type P (EPDM). Blue corrugated with red spiral stripe.

COUPLINGS:

PACKAGING:

100' length coiled and wrapped in polyethylene.

BRANDING:

Continuous transfer label. Example: “GATES® Stallion® U.S. Pat. No. 5,647,400 Crush Resistant Acid-Chemical Suction/Discharge 200 PSI (1.38MPa) WP Made In U.S.A. For your safety: Use Permanent Fittings Only”

SPECIAL ORDER REQUIREMENTS:

REMNANT LENGTHS:

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 11

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Acid-Chemical Hose

Mustang® (Specification 4695/4695G)

Black Cover (4695) Nom. I.D. (In.) 3/4 3/4 1 1 1 1/4 1 1/4 1 1/2 2 2 2 1/2 2 1/2 3 3 4 4

(mm) 19.1 19.1 25.4 25.4 31.8 31.8 38.1 50.8 50.8 63.5 63.5 76.2 76.2 101.6 101.6

Nom. O.D. (In.) 1.25 1.25 1.50 1.50 1.75 1.75 2.04 2.54 2.54 3.05 3.05 3.58 3.58 4.69 4.69

(mm) 31.8 31.8 38.1 38.1 44.5 44.5 51.8 64.5 64.5 77.5 77.5 90.9 90.9 119.1 119.1

Max. W.P. (psi) 200 200 200 200 200 200 200 200 200 150 150 150 150 125 125

(MPa) 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.03 1.03 1.03 1.03 .86 .86

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(MPa) 1.38 1.38 1.38 1.38 1.03 1.03

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 4.0 4.0 5.0 5.0 6.0 6.0 8.0 9.0 9.0 12.0 12.0 18.0 18.0 24.0 24.0

(mm Hg) 762 762 762 762 762 762

Min. Bend Radius (In.) 5.0 8.0 9.0 9.0 18.0 18.0

(mm) 102 102 127 127 152 152 203 229 229 305 305 457 457 610 610

Wt. Per Ft. (Lbs.) .45 .45 .56 .56 .66 .66 .87 1.10 1.10 1.40 1.40 1.79 1.79 2.72 2.72

(Kg) .20 .20 .25 .25 .30 .30 .40 .50 .50 .64 .64 .81 .81 1.23 1.23

Standard Pack 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft.

Stock (X) or Minimum Order Qty. X 400 ft. X 400 ft. X 400 ft. X X 400 ft. X 400 ft. X 400 ft. X 400 ft.

Gates Item No. 4695-0002 4695-0737 4695-0003 4695-0670 4695-0004 4695-0738 4695-0005 4695-0001 4695-0698 4695-0006 4695-0720 4695-0007 4695-0699 4695-0008 4695-0055

(mm) 127 203 229 229 457 457

Wt. Per Ft. (Lbs.) .56 .88 1.11 1.11 1.81 1.81

(Kg) .25 .40 .50 .50 .82 .82

Standard Pack 100 ft. 100 ft. 100 ft. 200 ft. 100 ft. 200 ft.

Stock (X) or Minimum Order Qty. X X X 400 ft. X 400 ft.

Gates Item No. 4695-0628 4695-0211 4695-0216 4695-0700 4695-0229 4695-0701

Green Cover (4695G) Nom. I.D. (In.) 1 1 1/2 2 2 3 3

(mm) 25.4 38.1 50.8 50.8 76.2 76.2

Nom. O.D. (In.) 1.50 2.04 2.54 2.54 3.58 3.58

(mm) 38.1 51.8 64.5 64.5 90.9 90.9

Max. W.P. (psi) 200 200 200 200 150 150

RECOMMENDED FOR:

NOTE: For applications requiring greater than 90% sulfuric acid contact Denver Product Application (303) 744-5070. Tank truck, barge, ship, or storage tank transfer of a variety of chemical products. Mustang contains a wire helix for full suction capability, as well as for routing hoses through tight bends. Its Modified Cross-linked Polyethylene tube stock is “best in class” for maintaining a tight seal with stainless steel fittings, and is designed for cleaning with “open end” 50 PSI steam or in a bath containing 10% (NaOH) @ 212°F (100°C). Cleaning in place (CIP) methods may be used. Not recommended for “closed steam” cleaning. Applications include over 950 basic chemicals that are building blocks for numerous chemicals used in a variety of industries. Reference Gates Chemical Resistance Table for proper hose selection.

TEMPERATURE:

-40°F to +250°F (-40°C to +121°C) normal service. Mustang is designed to withstand fluid temperatures to 250°F (+121°C), however the rating is dependent on the specific chemical conveyed. Contact Denver Product Application (303) 744-5070 for any chemical above 125°F (+52°C).

CONSTRUCTION:

PACKAGING: BRANDING: SPECIAL ORDER REQUIREMENTS:

REMNANT LENGTHS:

Tube: Reinforcement: Cover:

Type K (Gatron™ Modified Cross-linked Polyethylene.) Tan. High chemical resistance. Synthetic, high tensile textile cord with steel wire helix. Type P (EPDM). Black or green corrugated with orange spiral stripe. Blue, red, and yellow covers available on special order.

100' length coiled and wrapped in polyethylene. Continuous transfer label. Example: “GATES® Mustang® Acid-Chemical Suction/Discharge 200 PSI (1.38MPa) WP Made In U.S.A. For your safety: Use Permanent Couplings above 125°F.” Blue, red, and yellow covers are made to order and require minimum production order quantities of 400 feet per size. For price, add 10% (x1.10) to price. Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 12

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Acid-Chemical Hose

Mustang® Crush Resistant (Specification 4695M)

Nom. I.D. (In.) 3/4 1 1 1/2 2

(mm) 19.1 25.4 38.1 50.8

Nom. O.D. (In.) 1.36 1.61 2.13 2.63

(mm) 34.5 40.9 54.1 66.8

RECOMMENDED FOR:

TEMPERATURE:

CONSTRUCTION:

Max. W.P. (psi) 200 200 200 200

(MPa) 1.38 1.38 1.38 1.38

Suction (In. Hg) 20.0 20.0 20.0 20.0

(mm Hg) 508 508 508 508

Min. Bend Radius (In.) 4.0 5.0 8.0 9.0

(mm) 102 127 203 229

Wt. Per Ft. (Lbs.) .53 .64 .90 1.13

(Kg) .24 .29 .41 .51

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. 400 ft. X X X

Gates Item No. 4695-0607 4695-0608 4695-0609 4695-0610

NOTE: For applications requiring greater than 90% sulfuric acid contact Denver Product Application (303) 744-5070. Tank truck, barge, ship, or storage tank transfer of a variety of chemical products. Mustang Crush Resistant contains a monofilament helix for suction and crush resistant capability, as well as for routing hoses through tight bends. Its Modified Cross-linked Polyethylene tube stock is “best in class” for maintaining a tight seal with stainless steel fittings, and is designed for cleaning with “open end” 50 PSI steam or in a bath containing 10% (NaOH) @ 212°F (100°C). Cleaning in place (CIP) methods may be used. Not recommended for “closed steam” cleaning. Applications include over 950 basic chemicals that are building blocks for numerous chemicals used in a variety of industries. Reference Gates Chemical Resistance Table for proper hose selection. -40°F to +250°F (-40°C to +121°C) normal service. Mustang Crush Resistant is designed to withstand fluid temperatures to 250°F (+121°C), however the rating is dependent on the specific chemical conveyed. Contact Denver Product Application (303) 744-5070 for any chemical above 125°F (+52°C). Tube: Reinforcement: Cover:

Type K (Gatron™ Modified Cross-linked Polyethylene.) Tan. High chemical resistance. Synthetic, high tensile textile with monofilament helix and static wire providing crush and kink resistance. Type P (EPDM). Black corrugated with orange spiral stripe. Green, blue, red, and yellow covers available on special order.

COUPLINGS:

Gates has tested hose assemblies at the maximum rated service temperature to assure your safety. Use 7, 8, or 49 for fluid temperatures to 125°F (+52°C). Use permanent fittings only 71 or 73 for fluid temperatures above 125°F (+52°C) and up to 250°F (+121°C). Reference the Hose Coupling Section.

PACKAGING:

100' length coiled and wrapped in polyethylene.

BRANDING:

Continuous transfer label. Example: “GATES® Mustang® Crush Resistant Acid-Chemical Suction/Discharge 200 PSI (1.38MPa) WP Made In U.S.A. For your safety: Use Permanent Couplings above 125°F.”

SPECIAL ORDER REQUIREMENTS:

Green, blue, red, and yellow covers are made to order and require minimum production order quantities of 400 feet per size. For price, add 10% (x1.10) to price. Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity.

REMNANT LENGTHS:

Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 13

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Acid-Chemical Hose

Appaloosa® (Specification 4695RG)

Nom. I.D. (In.) 1 1/2 2 3

(mm) 38.1 50.8 76.2

Nom. O.D. (In.) 1.97 2.47 3.51

(mm) 50.0 62.7 89.2

RECOMMENDED FOR:

TEMPERATURE:

CONSTRUCTION:

Max. W.P. (psi) 200 200 150

(MPa) 1.38 1.38 1.03

Suction (In. Hg) 30.0 30.0 30.0

(mm Hg) 762 762 762

Min. Bend Radius (In.) 8.0 9.0 18.0

(mm) 203 229 457

Wt. Per Ft. (Lbs.) .76 .97 1.58

(Kg) .35 .44 .72

Standard Pack 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. 200 ft. 200 ft. 200 ft.

Gates Item No. 4695-0665 4695-0666 4695-0668

Use for tank truck, barge, ship, or storage tank transfer of a variety of chemical products where external abrasion resistance is critical. Appaloosa contains a wire helix for full suction capability, as well as for routing hoses through tight bends. Its Modified Cross-linked Polyethylene tube stock is “best in class” for maintaining a tight seal with stainless steel fittings and is designed for cleaning with “open end” 50 PSI steam or in a bath containing 10% (NaOH) @ 212°F (100°C). Cleaning in place (CIP) methods may be used. Not recommended for “closed steam” cleaning. Capable of handling more than 950 basic chemicals. Reference Gates Chemical Resistance Table for proper hose selection. -40°F to +225°F (-40°C to +107°C) normal service. Appaloosa is designed to withstand fluid temperatures to 225°F (+107°C), however the rating is dependent on the specific chemical conveyed. Contact Denver Product Application (303) 744-5070 for any chemical above 125°F (+52°C). Tube: Reinforcement: Cover:

Type K (Gatron™ Modified Cross-linked Polyethylene.) Tan. High chemical resistance. Synthetic, high tensile textile with steel wire helix. Type L (UHMWPE) over a base of Type P (EPDM). Black corrugated cover with green dots and a green spiral stripe.

COUPLINGS:

PACKAGING:

100' length coiled and wrapped in polyethylene.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Continuous transfer label. Example: “GATES® Appaloosa® Acid-Chemical Suction/Discharge 200 PSI (1.38MPa) WP Made In U.S.A. For your safety: Use Permanent Couplings above 125°F.” Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 14

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Acid-Chemical Hose

Renegade™ (Specification 4697G)

Nom. I.D. (In.) 3/4 1 1 1 1/4 1 1/2 1 1/2 2 2 2 1/2 3 3 4

(mm) 19.1 25.4 25.4 31.8 38.1 38.1 50.8 50.8 63.5 76.2 76.2 101.6

Nom. O.D. (In.) 1.22 1.47 1.47 1.72 2.00 2.00 2.50 2.50 3.01 3.53 3.53 4.53

(mm) 31.0 37.3 37.3 43.7 50.8 50.8 63.5 63.5 76.5 89.7 89.7 115.1

Max. W.P. (psi) 200 200 200 200 200 200 200 200 150 150 150 125

(MPa) 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.03 1.03 1.03 .86

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 4.0 5.0 5.0 6.0 8.0 8.0 9.0 9.0 12.0 18.0 18.0 24.0

(mm) 102 127 127 152 203 203 229 229 305 457 457 610

Wt. Per Ft. (Lbs.) .41 .51 .51 .60 .78 .78 .99 .99 1.28 1.63 1.63 2.11

(Kg) .19 .23 .23 .27 .35 .35 .45 .45 .58 .74 .74 .96

Standard Pack 100 ft. 100 ft. 200 ft. 100 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 100 ft. 200 ft. 100 ft.

Stock (X) or Minimum Order Qty. X X 400 ft. X X 400 ft. X 400 ft. X X 400 ft. X

Gates Item No. 4697-0014 4697-0015 4697-0057 4697-0016 4697-0017 4697-0058 4697-0018 4697-0059 4697-0019 4697-0020 4697-0022 4697-0021

RECOMMENDED FOR:

Tank truck, barge, ship, or storage tank transfer of a variety of chemical products. Renegade contains a wire helix for full suction capability, as well as for routing hoses through tight bends. The Ultrahigh Molecular Weight Polyethylene tube stock has excellent chemical resistance and is backed by Gates Gatron™ for flex fatigue safety at the coupling. Renegade is designed for easy cleaning in bath containing 10% (NaOH) @ 212°F (+100°C). Cleaning in place (CIP) methods may be used. Applications include over 450 basic chemicals which are building blocks for numerous chemicals used in a variety of industries. Reference Gates Chemical Resistance Table for proper hose selection.

TEMPERATURE:

-40°F to +212°F (-40°C to +100°C) normal service. Renegade is designed to withstand fluid temperatures to 212°F (+100°C), however the rating is dependent on the specific chemical conveyed. Contact Denver Product Application (303) 744-5070 for any chemical above 125°F (+52°C).

CONSTRUCTION:

Tube: Reinforcement: Cover:

Type L (Ultrahigh Molecular Weight Polyethylene). Clear, backed with Gatron™ Modified XLPE. Synthetic, high tensile textile with steel wire helix. Type P (EPDM). Green corrugated with yellow spiral stripe.

COUPLINGS:

Gates has tested hose assemblies at the maximum rated service temperature to assure your safety. Use 7, 8, or 49 for fluid temperatures to 125°F (+52°C). Use permanent fittings only 71 or 73 for fluid temperatures above 125°F (+52°C) and up to 212°F (+100°C). Reference the Hose Coupling Section.

PACKAGING:

100' length coiled and wrapped in polyethylene.

BRANDING: SPECIAL ORDER REQUIREMENTS:

REMNANT LENGTHS:

Continuous transfer label. Example: “GATES® Renegade™ Acid-Chemical Suction/Discharge 200 PSI (1.38MPa) WP Made In U.S.A. For your safety: Use Permanent Couplings above 125°F.” Black, red, blue and yellow covers are made to order and require minimum production order quantities of 400 feet per size. For price, add 10% (x1.10) to price. Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 15

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Acid-Chemical Hose

Colt® (Specification 4696A)

Nom. I.D. (In.) 3/4 1 1 1/4 1 1/4 1 1/2 2 2 1/2 3 3 4 6

(mm) 19.1 25.4 31.8 31.1 38.1 50.8 63.5 76.2 76.2 101.6 152.4

Nom. O.D. (In.) 1.27 1.52 1.79 1.79 2.04 2.54 3.05 3.60 3.60 4.60 6.78

(mm) 32.3 38.6 45.5 45.5 51.8 64.5 77.5 91.4 91.4 116.8 172.2

RECOMMENDED FOR:

TEMPERATURE:

CONSTRUCTION:

Max. W.P. (psi) 150 150 150 150 150 150 150 150 150 125 125

(MPa) 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 .86 .86

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 3.0 3.5 4.0 4.0 5.0 6.0 9.0 11.0 11.0 16.0 24.0

(mm) 76 89 102 102 127 152 229 279 279 406 610

Wt. Per Ft. (Lbs.) .50 .61 .77 .77 .89 1.11 1.48 1.94 1.94 2.52 4.95

(Kg) .23 .28 .35 .35 .40 .50 .67 .88 .88 1.14 2.25

Standard Pack 100 ft. 100 ft. 100 ft. 200 ft. 100 ft. 100 ft. 100 ft. 100 ft. 200 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. 400 ft. X 400 ft. 400 ft. X X 400 ft. X 400 ft. X X

Gates Item No. 4696-0002 4696-0001 4696-0003 4696-0203 4696-0004 4696-0005 4696-0006 4696-0009 4696-0013 4696-0012 4696-0017

Tank truck, barge ship, or storage tank transfer of a variety of mild chemical products. Colt contains a wire helix for full suction capability, as well as for routing hoses through tight bends. Its EPDM tube stock will withstand 250°F (+121°C) applications. Reference Gates Chemical Resistance Table for proper hose selection. -40°F to +250°F (-40°C to +121°C) normal service. Colt is designed to withstand fluid temperatures to 250°F (+121°C), however the rating is dependent on the specific chemical conveyed. Contact Denver Product Application (303) 744-5070 for any chemical above 125°F (+52°C). Tube: Reinforcement: Cover:

Type P (EPDM). Black. Mild chemical resistance. Synthetic, high tensile textile with steel wire helix. Type P (EPDM). Yellow corrugated with green spiral stripe.

COUPLINGS:

PACKAGING:

100' length coiled and wrapped in polyethylene.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Continuous transfer label. Example: “GATES® Colt® Acid-Chemical Suction/Discharge 150 PSI (1.03MPa) WP Made In U.S.A. For your safety: Use Permanent Couplings above 125°F.” Special production runs require minimum order quantities of 400 feet for sizes through 4" and 200 feet for sizes above 4". If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 16

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Acid-Chemical Hose

Thermo AG® 570 (Ag Spray) (Specification 4465)

Nom. I.D. (In.) 3/8 3/8 1/2 1/2 3/4 3/4

(mm) 9.5 9.5 12.7 12.7 19.1 19.1

Nom. O.D. (In.) .67 .67 .81 .81 1.08 1.08

(mm) 17.0 17.0 20.6 20.6 27.4 27.4

Max. W.P. (psi) 570 570 570 570 570 570

(MPa) 3.93 3.93 3.93 3.93 3.93 3.93

Suction (In. Hg) 25.0 25.0 25.0 25.0 25.0 25.0

(mm Hg) 635 635 635 635 635 635

Min. Bend Radius (In.) 4.0 4.0 5.0 5.0 6.0 6.0

(mm) 102 102 127 127 152 152

Wt. Per Ft. (Lbs.) .12 .12 .17 .17 .27 .27

(Kg) .05 .05 .08 .08 .12 .12

Standard Pack 300 ft. 400 ft. 300 ft. 400 ft. 300 ft. 400 ft.

Stock (X) or Minimum Order Qty. X X X X X X

Gates Item No. 4465-1701 4465-1702 4465-1704 4465-1705 4465-1706 4465-1707

*Working Pressure and Suction at +72°F (+22°C).

RECOMMENDED FOR:

Spraying lawns, trees and similar applications with diluted solutions of water and oil based pesticides and herbicides. For pesticides or herbicides containing more than 2% Toluene or Xylene, use Gates 77B.

TEMPERATURE:

-10°F to +130°F (-23°C to +55°C). Maximum temperature dependent on pesticide/herbicide or chemicals conveyed. For temperatures above 120°F (+49°C), contact Denver Product Application (303) 744-5070.

CONSTRUCTION:

Tube: Reinforcement: Cover:

Type G (PVC). Yellow. Synthetic, high tensile textile cord. Type G (PVC). Yellow. Striated.

COUPLINGS:

8, 14 or 15, 21 (multiple clamps required), 48, 72 Gates Power Crimp®, or 75 Gates GLX® couplings. Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled in a polyethylene bag.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Continuous ink brand. Example: “3/8" 570 PSI WP SPRAY HOSE JAPAN” None. None.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 17

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Acid-Chemical Hose

Thermo AG® 800 (Ag Spray) (Specification 4465)

Nom. I.D. (In.) 3/8 3/8 1/2 1/2 3/4 3/4

(mm) 9.5 9.5 12.7 12.7 19.1 19.1

Nom. O.D. (In.) .69 .69 .84 .84 1.41 1.41

(mm) 17.5 17.5 21.3 21.3 35.8 35.8

Max. W.P. (psi) 800 800 800 800 800 800

(MPa) 5.52 5.52 5.52 5.52 5.52 5.52

Suction (In. Hg) 25.0 25.0 25.0 25.0 25.0 25.0

(mm Hg) 635 635 635 635 635 635

Min. Bend Radius (In.) 4.0 4.0 5.0 5.0 6.0 6.0

(mm) 102 102 127 127 152 152

Wt. Per Ft. (Lbs.) .14 .14 .18 .18 .30 .30

(Kg) .06 .06 .08 .08 .14 .14

Standard Pack 300 ft. 400 ft. 300 ft. 400 ft. 300 ft. 400 ft.

Stock (X) or Minimum Order Qty. X X X X X X

Gates Item No. 4465-1361 4465-1362 4465-1371 4465-1372 4465-1381 4465-1382

*Working Pressure and Suction at +72°F (+22°C).

RECOMMENDED FOR:

TEMPERATURE:

CONSTRUCTION:

Tube: Reinforcement: Cover:

Type G (PVC). Green. Synthetic, high tensile textile cord. Type G (PVC). Green. Striated.

COUPLINGS:

8, 14 or 15, 21 (multiple clamps required), 48, 72 Gates Power Crimp®, or 75 Gates GLX® couplings. Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled in a polyethylene bag.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Continuous ink brand. Example: “1/2" 800 PSI WP SPRAY HOSE JAPAN” None. None.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 18

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

77B (Paint Spray and Chemical)

Acid-Chemical Hose

(Specification 3207NN/3207T) Nom. I.D. (In.) 1/4 5/16 3/8 1/2 3/4

(mm) 6.4 7.9 9.5 12.7 19.1

Nom. O.D. (In.) .52 .59 .67 .87 1.16

(mm) 13.2 15.0 17.0 22.1 29.5

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 500 500 500 750 750

(MPa) 3.45 3.45 3.45 5.17 5.17

Suction (In. Hg) 30.0 30.0 30.0 25.0 25.0

(mm Hg) 762 762 762 635 635

Min. Bend Radius (In.) 3.0 3.0 3.0 5.0 6.0

(mm) 76 76 76 127 152

Wt. Per Ft. (Lbs.) .09 .11 .14 .23 .35

(Kg) .04 .05 .06 .10 .16

Standard Pack Reel Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X X X

Gates Item No. 3207-0290 3207-0291 3207-0292 3207-0294 3207-0296

Paint spray applications, as well as transfer of petroleum based products (aliphatic, aromatic and chlorinated hydrocarbon such as Toluene, Xylene, Benzene, gasoline and carbon tetrachloride). Reference Gates Chemical Resistance Table for proper hose selection. Compatible with commercially available Bio-Diesel fuels up to B-100. NOT RECOMMENDED FOR ACIDS OR USE IN HIGH PRESSURE PAINT SPRAY APPLICATIONS REQUIRING A STATIC CONDUCTIVE HOSE. -40°F to +150°F (-40°C to +66°C) continuous service. NOTE: Contact Denver Product Application (303) 7445070 when conveying chemicals above 120°F (+49°C). Tube: Reinforcement: Cover:

Type Z (Special flexible Nylon 11). Clear. Synthetic, high tensile textile cord. Type A (Neoprene). Black.

COUPLINGS:

48. For paint service: Binks 3 piece compression ring only. Reference the Hose Coupling Section.

PACKAGING:

1/4" through 1/2": Packaged in 600' to 800' reels. Maximum 4 pieces. One length 25' to 50'. Maximum of 2 pieces under 100'. 3/4": Packaged in 300' to 400' reels. Maximum 3 pieces. One length between 25' to 50'. All other lengths over 50'. Maximum 2 pieces under 100'.

BRANDING:

Continuous ink print label. Example: “GATES® 77B PAINT SPRAY AND CHEMICAL 3/8" (9.5mm) 500 PSI (3.45MPa) WP Made In U.S.A.”

SPECIAL ORDER REQUIREMENTS:

Special production runs require minimum order quantities of 5,000 feet for all sizes except 3/8". 3/8" requires 25,000 feet.

REMNANT LENGTHS:

None.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 19

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

19B Plant Master®

Air and Multi-Purpose Hose

(Specification 3219AR) Nom. I.D. (In.) 3/16 1/4 1/4 5/16 5/16 3/8 3/8 1/2 1/2 5/8 5/8 3/4 3/4 1 1 1 1/4 1 1/4 1 3/8 1 3/8 1 1/2 1 1/2

(mm) 4.8 6.4 6.4 7.9 7.9 9.5 9.5 12.7 12.7 15.9 15.9 19.1 19.1 25.4 25.4 31.8 31.8 34.9 34.9 38.1 38.1

Nom. O.D. (In.) .43 .50 .62 .62 .69 .69 .75 .84 .88 .94 1.00 1.09 1.19 1.38 1.50 1.75 1.75 1.87 1.88 2.00 2.00

(mm) 10.9 12.7 15.8 15.8 17.5 17.5 19.1 21.3 22.4 23.9 25.4 27.7 30.2 35.1 38.1 44.5 44.5 47.5 47.8 50.8 50.8

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 500 250 500 250 500 250 500 250 500 250 500 250 500 250 500 250 500 250 500 250 500

(MPa) 3.45 1.72 3.45 1.72 3.45 1.72 3.45 1.72 3.45 1.72 3.45 1.72 3.45 1.72 3.45 1.72 3.45 1.72 3.45 1.72 3.45

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 25.0 25.0 20.0 20.0 20.0 20.0 10.0 20.0 10.0 10.0 10.0 10.0 10.0 10.0

(mm Hg) 762 762 762 762 762 762 762 635 635 508 508 508 508 254 508 254 254 254 254 254 254

Min. Bend Radius (In.) 3.0 3.0 3.0 3.0 3.0 3.0 3.0 5.0 5.0 6.0 6.0 6.0 6.0 8.0 8.0 10.0 10.0 10.0 10.0 12.0 12.0

(mm) 76 76 76 76 76 76 76 127 127 152 152 152 152 203 203 254 254 254 254 305 305

Wt. Per Ft. (Lbs.) .07 .09 .14 .13 .17 .15 .18 .20 .23 .22 .27 .28 .38 .41 .55 .67 .76 .71 .73 .78 .78

(Kg) .03 .04 .06 .06 .08 .07 .08 .09 .10 .10 .12 .13 .17 .19 .25 .30 .30 .32 .33 .35 .35

Standard Pack Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X X 5,000 ft. X X X X X X X X X X X 5,000 ft. 5,000 ft. 5,000 ft. X 5,000 ft.

Gates Item No. 3219-2901 3219-2902 3219-2903 3219-2904 3219-2905 3219-2906 3219-2907 3219-2908 3219-2909 3219-2910 3219-2911 3219-2912 3219-2913 3219-2914 3219-2915 3219-2916 3219-2917 3219-2918 3219-2919 3219-2920 3219-2921

Applications requiring a premium grade braided hose, with excellent flexibility and maximum resistance to air, water, petroleum oils, gasoline, kerosene and fuel oil (to 120°F) and lubricating oils (to 212°F). Excellent weather and ozone resistance. NOTE: Not recommended for constant contact with fuels. Not recommended for Bio-Diesel fuels. -40°F to +212°F (-40°C to +100°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Braided, high tensile synthetic textile cord. Type C2 (Modified Nitrile). Red.

COUPLINGS:

19 (up through 1/2" only), 3 or 4, (up through 1/2" with 20 brass ferrules, up through 1" with bands), 1, 14, or 15 (all sizes), 72 Gates Power Crimp® or 75 Gates GLX®. Reference the Hose Coupling Section.

PACKAGING:

3/16" through 1/2": Packaged in 500' to 750' reels. Maximum 3 pieces. Minimum length 50'. 5/8" through 1": Packaged in 400' to 650' reels. Maximum 3 pieces. Minimum length 50'. 1 1/4" & over: Packaged in 250' to 400' reels. Maximum 3 pieces. Minimum length 50'.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous ink brand. Example: “GATES® 19B Plant Master® Multi-Purpose 3/8" (9.5mm) 250 PSI (1.72MPa) WP Made in U.S.A.” Special production runs require minimum order quantities of 5,000 feet. None. Mil-H-2815G Section 3.12.2 off-gassing for breathing applications such as supplied air respirators, through 1/2" I.D. Nonconductive at 1000 volts D.C. Electrical resistance is greater than one megohm per inch when subjected to 1000 volts D.C. Storage and use may adversely affect electrical properties. Tube: RMA (Class A) High oil resistance. Cover: RMA (Class B) Medium oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 20

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

119B Plant Master®

Air and Multi-Purpose Hose

(Specification 3219AB) Nom. I.D. (In.) 1/4 1/4 5/16 3/8 3/8 1/2 1/2 5/8 3/4 3/4 1 1 1 1/4 1 1/2

(mm) 6.4 6.4 7.9 9.5 9.5 12.7 12.7 15.9 19.1 19.1 25.4 25.4 31.8 38.1

Nom. O.D. (In.) .50 .62 .62 .69 .75 .84 .88 .94 1.09 1.19 1.38 1.50 1.75 2.00

(mm) 12.7 15.8 15.8 17.5 19.1 21.3 22.4 23.9 27.7 30.2 35.1 38.1 44.5 50.8

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 250 500 250 250 500 250 500 250 250 500 250 500 250 250

(MPa) 1.72 3.45 1.72 1.72 3.45 1.72 3.45 1.72 1.72 3.45 1.72 3.45 1.72 1.72

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 25.0 25.0 20.0 20.0 20.0 10.0 20.0 10.0 10.0

(mm Hg) 762 762 762 762 762 635 635 508 508 508 254 508 254 254

Min. Bend Radius (In.) 3.0 3.0 3.0 3.0 3.0 5.0 5.0 6.0 6.0 6.0 8.0 8.0 10.0 12.0

(mm) 76 76 76 76 76 127 127 152 152 152 203 203 254 305

Wt. Per Ft. (Lbs.) .09 .16 .13 .15 .21 .21 .26 .23 .29 .42 .42 .62 .69 .81

(Kg) .04 .07 .06 .07 .10 .10 .12 .10 .13 .19 .19 .28 .31 .37

Standard Pack Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X 5,000 ft. X X 5,000 ft. 5,000 ft. 5,000 ft. 5,000 ft. X 5,000 ft. X 5,000 ft. 5,000 ft. 5,000 ft.

Gates Item No. 3219-2930 3219-2931 3219-2932 3219-2933 3219-2934 3219-2935 3219-2936 3219-2937 3219-2938 3219-2939 3219-2940 3219-2941 3219-2942 3219-2943

Type C (Nitrile). Black. Braided, high tensile synthetic textile cord. Type A (Neoprene). Black.

COUPLINGS:

PACKAGING:

1/4" through 1/2": Packaged in 500' to 750' reels. Maximum 3 pieces. Minimum length 50'. 5/8" through 1": Packaged in 400' to 650' reels. Maximum 3 pieces. Minimum length 50'. 1 1/4" & over: Packaged in 250' to 400' reels. Maximum 3 pieces. Minimum length 50'.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous ink brand. Example: “GATES® 119B Plant Master® Multi-Purpose 3/8" (9.5mm) 250 PSI (1.72MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 5,000 feet. None. Mil-H-2815G Section 3.12.2 off-gassing for breathing applications such as supplied air respirators, through 1/2" I.D. Nonconductive at 1000 volts D.C. Electrical resistance is greater than one megohm per inch when subjected to 1000 volts D.C. Storage and use may adversely affect electrical properties. Tube: RMA (Class A) High oil resistance. Cover: RMA (Class B) Medium oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 21

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Terminator®

Air and Multi-Purpose Hose

(Specification 3202T/3202TW) Nom. I.D. (In.) 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2

(mm) 6.4 9.5 12.7 19.1 25.4 31.8 38.1 50.8 50.8

Nom. O.D. (In.) .57 .75 .89 1.22 1.51 1.78 2.09 2.64 2.64

(mm) 14.5 19.1 22.6 31.0 38.4 45.2 53.1 67.1 67.1

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 501 501 501 501 501 501 501 501 501

(MPa) 3.45 3.45 3.45 3.45 3.45 3.45 3.45 3.45 3.45

Suction (In. Hg) 30.0 25.0 25.0 15.0 10.0 10.0 10.0 10.0 10.0

(mm Hg) 762 635 635 381 254 254 254 254 254

Min. Bend Radius (In.) 3.0 3.0 5.0 6.0 8.0 10.0 12.0 14.0 14.0

(mm) 76 76 127 152 203 254 305 356 356

Wt. Per Ft. (Lbs.) .12 .19 .25 .42 .57 .73 .96 1.35 1.35

(Kg) .05 .09 .11 .19 .26 .33 .44 .61 .61

Standard Pack Reel Reel Reel Reel Reel Reel 100 ft. 100 ft. 200 ft.

Stock (X) or Minimum Order Qty. X X X X X X X X 400 ft.

Gates Item No. 3202-0001 3202-0006 3202-0011 3202-0016 3202-0021 3202-0027 3202-0029 3202-0032 3202-0033

Applications requiring a premium-quality, multi-purpose hose with superior abrasion resistance for air, oil and some chemical applications. Excellent durability for extra long life in these applications: mining, air drill, construction, poultry plants and other severe service. Excellent weather and ozone resistance. NOTE: Due to Terminator’s 501 PSI working pressure, care should be taken to properly select couplings to match. Hose assembly working pressure is the working pressure of the lowest rated component. -40°F to +212°F (-40°C to +100°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Synthetic, high tensile textile cord. Type C4 (Carboxylated Nitrile). Yellow.

COUPLINGS:

19 (up through 1/2" only), 1, 3 or 4, (up through 1/2" with 20 brass ferrules, up through 1" with bands), 15, 71, 72 Gates Power Crimp®, 73 (up to 250 psi), 74 Gates Mega Crimp® or 75 Gates GLX®. Reference the Hose Coupling Section.

PACKAGING:

Minimum of 90% of hose reels will be 1-piece lengths. 1/4" through 3/4": Packaged in 500' to 700' reels. Maximum 2 pieces in 50' increments. 1" and 1 1/4": Packaged in 350' reels. Maximum 3 pieces. Minimum length 50'. 1 1/2" and 2": Packaged 100' coiled and wrapped in polyethylene.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous ink brand. Example: “GATES® TERMINATOR® 501 PSI (3.45MPa) WP 3/4" (19.1mm) FLAME RESISTANT MSHA 2G-IC-11C MADE IN USA” Special production runs require minimum order quantities of 25,000 feet for sizes through 3/4", 5,000 feet for 1" and 1 1/4", 400 feet for 1 1/2" and larger. None. Meets MSHA 30 CFR 18.65. Flame resistant. All sizes except 1 1/2" and 2" are nonconductive at 1000 volts D.C. Electrical resistance is greater than one megohm per inch when subjected to 1000 volts D.C. Storage and use may adversely affect electrical properties. Tube: RMA (Class A) High oil resistance. Cover: RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 22

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

LOL Plus (Lock-On Hose)

Air and Multi-Purpose Hose

(Specification 3284D, E, G, H, R, Y)

Color Black Black Black Black Black Blue Blue Blue Blue Blue Red Red Red Red Red Green Green Green Green Green Gray Gray Gray Gray Gray Yellow Yellow Yellow Yellow Yellow

Nom. I.D. (In.) 1/4 3/8 1/2 5/8 3/4 1/4 3/8 1/2 5/8 3/4 1/4 3/8 1/2 5/8 3/4 1/4 3/8 1/2 5/8 3/4 1/4 3/8 1/2 5/8 3/4 1/4 3/8 1/2 5/8 3/4

(mm) 6.4 9.5 12.7 15.9 19.1 6.4 9.5 12.7 15.9 19.1 6.4 9.5 12.7 15.9 19.1 6.4 9.5 12.7 15.9 19.1 6.4 9.5 12.7 15.9 19.1 6.4 9.5 12.7 15.9 19.1

Nom. O.D. (In.) .47 .63 .77 .94 1.06 .47 .63 .77 .94 1.06 .47 .63 .77 .94 1.06 .47 .63 .77 .94 1.06 .47 .63 .77 .94 1.06 .47 .63 .77 .94 1.06

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

(mm) 11.9 15.9 19.6 23.9 26.9 11.9 15.9 19.6 23.9 26.9 11.9 15.9 19.6 23.9 26.9 11.9 15.9 19.6 23.9 26.9 11.9 15.9 19.6 23.9 26.9 11.9 15.9 19.6 23.9 26.9

Max. W.P. (psi) 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300

(MPa) 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07

Suction (In. Hg) 27.9 27.9 27.9 27.9 15.0 27.9 27.9 27.9 27.9 15.0 27.9 27.9 27.9 27.9 15.0 27.9 27.9 27.9 27.9 15.0 27.9 27.9 27.9 27.9 15.0 27.9 27.9 27.9 27.9 15.0

(mm Hg) 711 711 711 711 381 711 711 711 711 381 711 711 711 711 381 711 711 711 711 381 711 711 711 711 381 711 711 711 711 381

Min. Bend Radius (In.) 3.0 3.0 5.0 6.0 7.0 3.0 3.0 5.0 6.0 7.0 3.0 3.0 5.0 6.0 7.0 3.0 3.0 5.0 6.0 7.0 3.0 3.0 5.0 6.0 7.0 3.0 3.0 5.0 6.0 7.0

(mm) 76 76 127 152 178 76 76 127 152 178 76 76 127 152 178 76 76 127 152 178 76 76 127 152 178 76 76 127 152 178

Wt. Per Ft. (Lbs.) .09 .11 .15 .20 .24 .09 .11 .15 .20 .24 .09 .11 .15 .20 .24 .09 .11 .15 .20 .24 .09 .11 .15 .20 .24 .09 .11 .15 .20 .24

(Kg) .04 .05 .07 .09 .11 .04 .05 .07 .09 .11 .04 .05 .07 .09 .11 .04 .05 .07 .09 .11 .04 .05 .07 .09 .11 .04 .05 .07 .09 .11

Standard Pack Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X X X X X X X X X X X X X X X X 5,000 ft. X X X X X X X X X 5,000 ft. X

Gates Item No. 3201-1100 3201-1101 3201-1102 3201-1103 3201-1104 3201-1105 3201-1106 3201-1107 3201-1108 3201-1109 3201-1110 3201-1111 3201-1112 3201-1113 3201-1114 3201-1120 3201-1121 3201-1122 3201-1123 3201-1124 3201-1125 3201-1126 3201-1127 3201-1128 3201-1129 3201-1115 3201-1116 3201-1117 3201-1118 3201-1119

NOTE: Lock-On hose and couplings are not recommended for pressure surge applications or critical applications, such as permanent piping in residential or commercial buildings. Not recommended for gasoline or diesel fuels. Petroleum-base hydraulic oils, water, glycol antifreeze solutions, hot lubricating oils, and air. -40°F to +212°F (-40°C to +100°C) normal service. For air: 160°F (+71°C) only. For water emulsion, see Gates Hydraulic Hose Catalog #35093. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Braided, high tensile synthetic textile cord. Type A (Neoprene). Black. Type C2 (Modified Nitrile). Blue, Red, Yellow, Green or Gray.

COUPLINGS:

75 Gates GLX®, Gates Hydraulic Lock-On Couplings. NOTE: Do not use clamps with Lock On fittings. (Reference Gates Hydraulic Hose Catalog #35093) or clamp over beaded nipple. Reference the Hose Coupling Section.

PACKAGING:

1/4" through 1/2": Packaged in 300' reels. Maximum of 3 pieces per reel. Minimum length 50'. 5/8": Packaged in 250' reels. Maximum of 3 pieces per reel. Minimum length 50'. 3/4": Packaged in 225' reels. Maximum of 3 pieces per reel. Minimum length 50'.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous ink brand. Example: “GATES® LOL PLUS 12LOLA+ 3/4 INCH 300 PSI WP FLAME RESISTANT COVER MADE IN U.S.A.” Special production runs require minimum order quantities of 5,000 feet per size. None. Tube: Cover:

RMA (Class A) High oil resistance. RMA (Class B) Medium oil resistance. Flame resistant.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 23

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Python® Plus (Lock-On Hose)

Air and Multi-Purpose Hose

(Specification 3222B, G, R, Y, BK, GY)

Color Black Black Black Blue Blue Blue Red Red Red Green Green Green Gray Gray Gray Yellow Yellow Yellow

Nom. I.D. (In.) 1/4 3/8 1/2 1/4 3/8 1/2 1/4 3/8 1/2 1/4 3/8 1/2 1/4 3/8 1/2 1/4 3/8 1/2

(mm) 6.4 9.5 12.7 6.4 9.5 12.7 6.4 9.5 12.7 6.4 9.5 12.7 6.4 9.5 12.7 6.4 9.5 12.7

Nom. O.D. (In.) .54 .68 .81 .54 .68 .81 .54 .68 .81 .54 .68 .81 .54 .68 .81 .54 .68 .81

(mm) 13.7 17.3 20.6 13.7 17.3 20.6 13.7 17.3 20.6 13.7 17.3 20.6 13.7 17.3 20.6 13.7 17.3 20.6

Max. W.P. (psi) 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300

(MPa) 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07 2.07

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762 762 762 762 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 3.0 3.0 5.0 3.0 3.0 5.0 3.0 3.0 5.0 3.0 3.0 5.0 3.0 3.0 5.0 3.0 3.0 5.0

(mm) 76 76 127 76 76 127 76 76 127 76 76 127 76 76 127 76 76 127

Wt. Per Ft. (Lbs.) .11 .15 .18 .11 .15 .18 .11 .15 .18 .11 .15 .18 .11 .15 .18 .11 .15 .18

(Kg) .05 .07 .08 .05 .07 .08 .05 .07 .08 .05 .07 .08 .05 .07 .08 .05 .07 .08

Standard Pack Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X X X X 25,000 ft. X X 25,000 ft. X X X X X 25,000 ft. X X

Gates Item No. 3222-0183 3222-0184 3222-0185 3222-0143 3222-0144 3222-0145 3222-0333 3222-0334 3222-0335 3222-0233 3222-0234 3222-0235 3222-0283 3222-0284 3222-0285 3222-0083 3222-0084 3222-0085

RECOMMENDED FOR:

Air, water, oils, antifreeze solutions and applications where Lock-On fittings are used. NOTE: Lock-On hose is not recommended for applications where vibrations or pressure surges exist. Do not use oil for Lock-On fitting insertion purposes. Not recommended for gasoline or diesel fuels.

TEMPERATURE:

-20°F to +212°F (-29°C to +100°C) normal service. For air: 160°F (+71°C) only. For water emulsion, see Gates Hydraulic Hose Catalog #35093.

CONSTRUCTION:

Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Aramid tensile cord. Type A (Neoprene). Black. Type C2 (Modified Nitrile). Blue, Red, Yellow, Green or Gray.

COUPLINGS:

PACKAGING:

Minimum of 90% of hose reels will be 1-piece lengths. 1/4" through 1/2": Packaged in 500' to 700' reels. Maximum of 2 pieces per reel. All lengths in 50' increments.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous ink brand. Example: “GATES® PYTHON® PLUS LOCK-ON 1/2 INCH (12.7mm) 300 PSI (2.07MPa) WP NONCONDUCTIVE MADE IN USA” Special production runs require minimum order quantities of 25,000 feet per size. None. Nonconductive at 1000 volts D.C. Electrical resistance is greater than one megohm per inch when subjected to 1000 volts D.C. Storage and use may adversely affect electrical properties. Tube: RMA (Class A) High oil resistance. Cover: RMA (Class B) Medium oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 24

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Premo Flex®

Air and Multi-Purpose Hose

(Specification 3205R) Nom. I.D. (In.) 3/16 1/4 1/4 5/16 5/16 3/8 3/8 1/2 1/2 5/8 5/8 3/4 3/4 3/4 1 1 1/4 1 1/2

(mm) 4.8 6.4 6.4 7.9 7.9 9.5 9.5 12.7 12.7 15.9 15.9 19.1 19.1 19.1 25.4 31.8 38.1

Nom. O.D. (In.) .45 .50 .57 .56 .67 .66 .73 .85 .88 .98 .98 1.15 1.15 1.19 1.47 1.75 2.00

(mm) 11.2 12.7 14.5 14.2 17.0 16.8 18.5 21.6 22.4 24.9 24.9 29.2 29.2 30.2 37.3 44.5 50.8

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 250 250 315 250 315 250 315 250 315 250 315 250 250 315 250 250 250

(MPa) 1.72 1.72 2.17 1.72 2.17 1.72 2.17 1.72 2.17 1.72 2.17 1.72 1.72 2.17 1.72 1.72 1.72

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 25.0 25.0 20.0 20.0 20.0 20.0 20.0 10.0 10.0 10.0

(mm Hg) 762 762 762 762 762 762 762 635 635 508 508 508 508 508 254 254 254

Min. Bend Radius (In.) 2.0 2.0 2.0 2.0 2.0 3.0 3.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 8.0 10.0 12.0

(mm) 51 51 51 51 51 76 76 102 102 127 127 127 127 127 203 254 305

Wt. Per Ft. (Lbs.) .07 .09 .12 .10 .16 .14 .18 .22 .24 .27 .27 .36 .36 .40 .54 .67 .78

(Kg) .03 .04 .05 .05 .07 .06 .08 .10 .11 .12 .12 .16 .16 .18 .25 .30 .35

Standard Pack Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel 50 ft. Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. 25,000 ft. X X 25,000 ft. 25,000 ft. X X X X 25,000 ft. X X 25,000 ft. X X X X

Gates Item No. 3205-0010 3205-0015 3205-0016 3205-0020 3205-0021 3205-0025 3205-0026 3205-0030 3205-0031 3205-0035 3205-0036 3205-0040 3205-5040 3205-0041 3205-0046 3205-0049 3205-0055

Applications requiring a premium grade spiral hose with excellent flexibility and maximum resistance to air, water, petroleum oils and lubricating oils, (to 212°F). Recommended for gasoline, kerosene and fuel oil transfer only (to 120°F). Excellent weather and ozone resistance. -40°F to +212°F (-40°C to +100°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Synthetic, high tensile textile cord. Type C2 (Modified Nitrile). Red.

COUPLINGS:

19 (up through 1/2" only), 3 or 4, (up through 1/2" with 20 ferrules, up through 1" with bands), 1, 8, 14, 15, 72 Gates Power Crimp® or 75 Gates GLX®. Reference the Hose Coupling Section.

PACKAGING:

Minimum of 90% of hose reels will be 1-piece lengths. 3/16" through 3/4": Packaged in 500' to 700' reels. Maximum 2 pieces in 50' increments. 3/4" x 50': Packaged 200' per carton, each length coiled and tied. 1": Packaged in 300' to 400' reels. Maximum 2 pieces in 50' increments. 1 1/4": Packaged in 250' to 350' reels. Maximum 3 pieces in 25' increments. Minimum length 50'. 1 1/2": Packaged in 200' to 300' reels. Maximum 3 pieces in 25' increments. Minimum length 50'.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous ink brand. Example: “GATES® PREMO FLEX® MULTI-PURPOSE 3/8 INCH (9.5mm) 250 PSI (1.72MPa) WP NONCONDUCTIVE @1000V DC (>1 MEGOHM/IN.) MADE IN USA” Special production runs require minimum order quantities of 25,000 feet through 1 1/4" and 5,000 feet for 1 1/2". None. Nonconductive at 1000 volts D.C. Electrical resistance is greater than one megohm per inch when subjected to 1000 volts D.C. Storage and use may adversely affect electrical properties. Mil-H-2815G Section 3.12.2 offgassing for breathing applications such as supplied air respirators, for sizes 3/16" through 3/8", 3/4" and 1". Tube: RMA (Class A) High oil resistance. Cover: RMA (Class B) Medium oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 25

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

6B Dura Master®

Air and Multi-Purpose Hose

(Specification 3206) Nom. I.D. (In.) 1/4 1/4 5/16 3/8 3/8 1/2 1/2 3/4 3/4 1 1 1 1/4 1 1/2 2

(mm) 6.4 6.4 7.9 9.5 9.5 12.7 12.7 19.1 19.1 25.4 25.4 31.8 38.1 50.8

Nom. O.D. (In.) .50 .62 .62 .69 .75 .84 .88 1.09 1.19 1.38 1.50 1.73 1.98 2.56

(mm) 12.7 15.8 15.8 17.5 19.1 21.3 22.4 27.7 30.2 35.1 38.1 43.9 50.3 65.0

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 250 315 250 250 315 250 315 250 315 250 315 200 200 200

(MPa) 1.72 2.17 1.72 1.72 2.17 1.72 2.17 1.72 2.17 1.72 2.17 1.38 1.38 1.38

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 25.0 25.0 20.0 20.0 10.0 20.0 10.0 10.0 4.0

(mm Hg) 762 762 762 762 762 635 635 508 508 254 508 254 254 100

Min. Bend Radius (In.) 3.0 3.0 3.0 3.0 3.0 5.0 5.0 6.0 6.0 8.0 8.0 10.0 12.0 16.5

(mm) 76 76 76 76 76 127 127 152 152 203 203 254 305 419

Wt. Per Ft. (Lbs.) .09 .15 .14 .16 .20 .21 .25 .29 .40 .42 .59 .67 .79 .99

(Kg) .04 .07 .06 .07 .09 .10 .11 .13 .18 .19 .27 .30 .36 .45

Standard Pack Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel 100 ft.

Stock (X) or Minimum Order Qty. X X X X X X X X X X 5,000 ft. X X X

Gates Item No. 3206-0202 3206-0265 3206-0204 3206-0270 3206-0280 3206-0208 3206-0244 3206-0212 3206-0245 3206-0213 3206-0246 3206-0215 3206-0216 3206-3968

Applications requiring a heavy duty braided hose with good resistance to air, water and heat. For SAE oils intermittent contact only. -22°F to +158°F (-30°C to +70°C) continuous service. For 2" size only. -40°F to +200°F (-40°C to +93°C) continuous service. Tube: Reinforcement: Cover:

Type B1 (Specially compounded elastomer). Black. Braided, high tensile synthetic textile cord. Type B2 (Specially compounded elastomer). Black with red molded stripe. For size 2" only. Type P (EPDM). Red. All sizes through 1/2" are perforated.

COUPLINGS:

19 (up through 1/2" only), 1, 3 or 4, (up through 1/2" with 20 brass ferrules, up through 1" with bands), 72 Gates Power Crimp® or 75 Gates GLX®. Reusable couplings are not recommended. Reference the Hose Coupling Section.

PACKAGING:

1/4" through 1/2": Packaged in 500' to 750' reels. Maximum 3 pieces. Minimum length 50'. 3/4" and 1": Packaged in 400' to 650' reels. Maximum 3 pieces. Minimum length 50'. 1 1/4" & over: Packaged in 250' to 400' reels. Maximum 3 pieces. Minimum length 50'. 2" x 100': Packaged 100' per carton, coiled and tied.

BRANDING:

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous ink brand. Example: “GATES® 6B DURA MASTER® MULTI-PURPOSE 2 INCH (50.8mm) 200 PSI (1.38MPa) WP MADE IN INDIA” (2" size only) Continuous ink brand. Example: “GATES® 6B DURA MASTER® MULTI-PURPOSE 3/8 INCH (9.5mm) 250 PSI (1.72MPa) WP MADE IN U.S.A.” Special production runs require minimum order quantities of 5,000 feet for sizes through 1 1/2" and 600 feet for 2". None. Tube: Cover:

RMA (Class B) Medium oil resistance. RMA (Class C) Limited oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 26

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Duro Flex®

Air and Multi-Purpose Hose

(Specification 3200R/3200B) Nom. I.D. (In.) 1/4 1/4 3/8 3/8 1/2 1/2 5/8 5/8 3/4 3/4 3/4 1 1 1/4 1 1/2

(mm) 6.4 6.4 9.5 9.5 12.7 12.7 15.9 15.9 19.1 19.1 19.1 25.4 31.8 38.1

Nom. O.D. (In.) .50 .57 .66 .73 .81 .84 .98 .98 1.15 1.15 1.15 1.47 1.73 1.98

(mm) 12.7 14.5 16.8 18.5 20.6 21.3 24.9 24.9 29.2 29.2 29.2 37.3 43.9 50.3

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 250 300 250 300 250 300 250 300 250 250 300 250 250 250

(MPa) 1.72 2.07 1.72 2.07 1.72 2.07 1.72 2.07 1.72 1.72 2.07 1.72 1.72 1.72

Suction (In. Hg) 30.0 30.0 30.0 30.0 25.0 25.0 20.0 20.0 20.0 20.0 20.0 10.0 10.0 10.0

(mm Hg) 762 762 762 762 635 635 508 508 508 508 508 254 254 254

Min. Bend Radius (In.) 2.0 2.0 3.0 3.0 4.0 4.0 5.0 5.0 5.0 5.0 5.0 8.0 10.0 12.0

(mm) 51 51 76 76 102 102 127 127 127 127 127 203 254 305

Wt. Per Ft. (Lbs.) .09 .12 .14 .18 .19 .25 .27 .27 .36 .36 .36 .54 .67 .79

(Kg) .04 .05 .06 .08 .09 .11 .12 .12 .16 .16 .16 .25 .30 .36

Standard Pack Reel Reel Reel Reel Reel Reel Reel Reel Reel 50 ft. Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X X X X 25,000 ft. X X 25,000 ft. X X X X

Gates Item No. 3200-0002 3200-0003 3200-0006 3200-0007 3200-0008 3200-0009 3200-0010 3200-0011 3200-0012 3200-5012 3200-0013 3200-0014 3200-0015 3200-0016

Applications requiring maximum flexibility and good resistance to air, water and heat. For SAE oils intermittent contact only. -40°F to +200°F (-40°C to +93°C) continuous service. Tube: Reinforcement: Cover:

Type B1 (Specially compounded elastomer). Black. Synthetic, high tensile textile cord. Type P (EPDM). Red. All sizes through 1/2" have perforated cover. (Black, cover available on special order).

COUPLINGS:

19 (up through 1/2" only), 1, 3 or 4, (up through 1/2" with 20 brass ferrules, up through 1" with bands), 72 Gates Power Crimp® or 75 Gates GLX®. Reference the Hose Coupling Section.

PACKAGING:

Minimum of 90% of hose reels will be 1-piece lengths. 1/4" through 3/4": Packaged in 500' to 700' reels. Maximum 2 pieces in 50' increments. 3/4" x 50': Packaged 200' per carton, each length coiled and tied. 1": Packaged in 300' to 400' reels. Maximum 2 pieces in 50' increments. 1 1/4": Packaged in 300' reels. Maximum 2 pieces in 50' increments. 1 1/2": Packaged in 250' reels. Maximum 2 pieces in 50' increments.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous ink brand. Example: “GATES® DURO FLEX® MULTI-PURPOSE 3/8 INCH (9.5mm) 250 PSI (1.72MPa) WP MADE IN USA” Special production runs require minimum order quantities of 25,000 feet. Black cover is made to order. Special production run requirements apply. Price is 5% less than red cover. None. Tube: Cover:

RMA (Class B) Medium oil resistance. RMA (Class C) Limited oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 27

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Adapta Flex™ Red

Air and Multi-Purpose Hose

(Specification 3204E/3204S) Red Cover Nom. Nom. I.D. O.D. (In.) (mm) (In.) (mm) 1/4 6.4 .50 12.7 1/4 6.4 .50 12.7 1/4 6.4 .62 15.8 1/4 6.4 .53 13.5 5/16 7.9 .53 13.5 3/8 9.5 .66 16.8 3/8 9.5 .66 16.8 3/8 9.5 .67 17.0 1/2 12.7 .81 20.6 1/2 12.7 .81 20.6 1/2 12.7 .83 21.1 5/8 15.9 .97 24.6 5/8 15.9 .97 24.6 5/8 15.9 .97 24.6 3/4 19.1 1.11 28.2 3/4 19.1 1.11 29.2 3/4 19.1 1.15 29.2 3/4 19.1 1.15 29.2 3/4 19.1 1.15 29.2 1 25.4 1.39 35.3 1 25.4 1.39 35.3 1 25.4 1.47 37.3 NOTE: For 1 1/4" and 1 1/2" I.D. see

Max. W.P. (psi) (MPa) 200 1.38 250 1.72 250 1.72 300 2.07 200 1.38 200 1.38 250 1.72 300 2.07 200 1.38 250 1.72 300 2.07 200 1.38 250 1.72 250 1.72 200 1.38 250 1.72 250 1.72 300 2.07 300 2.07 150 1.03 200 1.38 300 2.07 Duro Flex®.

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 25.0 25.0 25.0 20.0 20.0 20.0 15.0 20.0 20.0 15.0 15.0 10.0 10.0 10.0

(mm Hg) 762 762 762 762 762 762 762 762 635 635 635 508 508 508 381 508 508 381 381 254 254 254

Min. Bend Radius (In.) 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 5.0 5.0 5.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 8.0 8.0 8.0

(mm Hg) 762 762

Min. Bend Radius (In.) 3.0 3.0

(mm) 76 76 76 76 76 76 76 76 127 127 127 152 152 152 152 152 152 152 152 203 203 203

Wt. Per Ft. (Lbs.) .09 .09 .15 .10 .09 .14 .14 .15 .19 .19 .20 .26 .26 .26 .31 .35 .35 .35 .35 .43 .45 .54

(mm) 76 76

Wt. Per Ea. (Lbs.) 6.95 6.95

(Kg) .04 .04 .07 .05 .04 .06 .06 .07 .09 .09 .09 .11 .11 .11 .14 .16 .16 .16 .16 .21 .21 .26

Standard Pack Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel 50 ft. Reel Reel 50 ft. Reel 50 ft. Reel Reel Reel

Stock (X) or Minimum Order Qty. X X 25,000 ft. X X X X X X X X X X 25,000 ft. X X 200 ft. (X) X 200 ft. (X) X X X

Gates Item No. 3204-1301 3204-1304 3204-1386 3204-1307 3204-1316 3204-1319 3204-1322 3204-1325 3204-1328 3204-1331 3204-1334 3204-1337 3204-1340 3204-5415 3204-1346 3204-1349 3204-5420 3204-1355 3204-5675 3204-1358 3204-1361 3204-1364

(Kg) 3.15 3.15

Standard Pack 50 ft. 50 ft.-BP**

Stock (X) or Minimum Order Qty. 8 ea. (X) 54 ea. (X)

Gates Item No. 3204-1720 3204-1900

Adapta Flex™ Assemblies Nom. I.D. (In.) 3/8 3/8

(mm) 9.5 9.5

Nom. O.D. (In.) .66 .66

(mm) 16.8 16.8

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 250 250

(MPa) 1.72 1.72

Suction (In. Hg) 30.0 30.0

Air and water applications requiring maximum flexibility in any industry, including mining, construction, agriculture, vehicle repair and in-plant operations. Outstanding resistance to heat and ozone. Suitable for light agricultural spraying, such as dilute solutions of herbicides. -40°F to +200°F (-40°C to +93°C) continuous service. Tube: Reinforcement: Cover:

Type P (EPDM). Black. Synthetic, high tensile textile cord. Type P (EPDM). Red. All sizes through 1/2" are perforated.

COUPLINGS:

19 (up through 1/2" only), 1, 3 or 4, (up through 1/2" with 20 brass ferrules, up through 1" with bands), 72 Gates Power Crimp® or 75 Gates GLX®. Reference the Hose Coupling Section.

PACKAGING:

Minimum of 90% of hose reels will be 1-piece lengths. 1/4" through 3/4": Packaged in 500' to 700' reels. Maximum 2 pieces in 50' increments. 3/8" x 50' coupled assemblies: **BP - Bulk Pack, 54 assemblies per pallet carton. 3/8" x 50' coupled assemblies: Coiled in a carton, 5 assemblies per carton. 5/8" x 50': Packaged 250' per carton, each length coiled and tied. 3/4" x 50': Packaged 200' per carton, each length coiled and tied. 1": Packaged in 300' to 400' reels. Maximum 2 pieces in 50' increments.

BRANDING:

Continuous ink brand. Example: “GATES® ADAPTA FLEX™ MULTI-PURPOSE 3/8 INCH (9.5mm) 250 PSI (1.72MPa) WP MADE IN USA”

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Special production runs require minimum order quantities of 25,000 feet per size. None.

STANDARDS:

Tube:

RMA (Class C) Limited oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 28

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Air and Multi-Purpose Hose

Adapta Flex™ Red Cover - UPS Shippable Reels (Specification 3204E)

Nom. I.D. (In.) 1/4 3/8 1/2 5/8 3/4 1

(mm) 6.4 9.5 12.7 15.9 19.1 25.4

Nom. O.D. (In.) .50 .66 .81 .97 1.11 1.40

(mm) 12.7 16.8 20.6 24.6 28.2 35.6

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 200 200 200 200 200 200

(MPa) 1.38 1.38 1.38 1.38 1.38 1.38

Suction (In. Hg) 30.0 30.0 25.0 20.0 15.0 10.0

(mm Hg) 762 762 635 508 381 254

Min. Bend Radius (In.) 3.0 3.0 5.0 6.0 6.0 8.0

(mm) 76 76 127 152 152 203

Wt. Per Ft. (Lbs.) .09 .14 .19 .26 .31 .45

(Kg) .04 .06 .09 .11 .14 .20

Standard Pack Reel Reel Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X X X X

Gates Item No. 3204-1373 3204-1375 3204-1377 3204-1379 3204-1381 3204-1383

Type P (EPDM). Black. Synthetic, high tensile textile cord. Type P (EPDM). Red. All sizes through 1/2" are perforated. (Blue, green and yellow covers available on special order).

COUPLINGS:

19 (up through 1/2" only), 1, 3 or 4, (up through 1/2" with 20 brass ferrules, up through 1" with bands), 72 Gates Power Crimp® or 75 Gates GLX®. Reference the Hose Coupling Section.

PACKAGING:

All sizes packaged on single piece reels meet UPS (United Parcel Service) size and weight requirements. 1/4" and 3/8": Packaged in 375' to 425' single piece reels. 1/2": Packaged in 225' to 275' single piece reels. 5/8": Packaged in 235' to 265' single piece reels. 3/4": Packaged in 185' to 215' single piece reels. 1": Packaged in 100' to 125' single piece reels.

BRANDING: SPECIAL ORDER REQUIREMENTS:

REMNANT LENGTHS: STANDARDS:

Continuous ink brand. Example: “GATES® ADAPTA FLEX™ MULTI-PURPOSE 3/8 INCH (9.5mm) 200 PSI (1.38MPa) WP MADE IN USA” Special production runs require minimum order quantities of 25,000 feet per size. Black, blue, green and yellow covers are made to order and require 25,000 feet orders by size/color. Prices for colors as follows from list price: Black less 5% (x.95). Blue, green and yellow contact Gates Corporation for pricing, order requirements and availability. None. Reels meet size and weight requirements of UPS (United Parcel Service). Tube: RMA (Class C) Limited oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 29

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Adapta Flex™ Black

Air and Multi-Purpose Hose

(Specification 3204EB/3204SB) Black Cover Nom. I.D. (In.) 1/4 1/4 1/4 3/8 3/8 1/2 1/2 5/8 3/4 3/4 3/4 1 1 1 1/4 1 1/2

(mm) 6.4 6.4 6.4 9.5 9.5 12.7 12.7 15.9 19.1 19.1 19.1 25.4 25.4 31.8 38.1

Nom. O.D. (In.) .50 .50 .62 .66 .66 .81 .81 .97 1.11 1.15 1.15 1.40 1.40 1.73 1.98

(mm) 12.7 12.7 15.8 16.8 16.8 20.6 20.6 24.6 28.2 29.2 29.2 35.6 35.6 43.9 50.3

Max. W.P. (psi) 200 250 250 200 250 200 250 200 200 250 250 150 200 250 250

(MPa) 1.38 1.72 1.72 1.38 1.72 1.38 1.72 1.38 1.38 1.72 1.72 1.03 1.38 1.72 1.72

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 25.0 25.0 20.0 15.0 20.0 20.0 10.0 10.0 10.0 10.0

(mm Hg) 762 762 762 762 762 635 635 508 381 508 508 254 254 254 254

Min. Bend Radius (In.) 3.0 3.0 3.0 3.0 3.0 5.0 5.0 6.0 6.0 6.0 6.0 8.0 8.0 10.0 12.0

(mm Hg) 762

Min. Bend Radius (In.) 3.0

(mm) 76 76 76 76 76 127 127 152 152 152 152 203 203 254 305

Wt. Per Ft. (Lbs.) .09 .09 .15 .14 .14 .19 .19 .26 .32 .35 .35 .44 .45 .68 .79

(Kg) .04 .04 .07 .06 .06 .09 .09 .12 .15 .16 .16 .20 .20 .31 .36

Standard Pack Reel Reel Reel Reel Reel Reel Reel Reel Reel Reel 50 ft. Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X 25,000 ft. 25,000 ft. X X X X X X X 200 ft. (X) X X X X

Gates Item No. 3204-1401 3204-1404 3204-1406 3204-1407 3204-1410 3204-1413 3204-1416 3204-1419 3204-1422 3204-1425 3204-5820 3204-1428 3204-1431 3204-1434 3204-1437

(mm) 76

Wt. Per Ea. (Lbs.) 7.05

(Kg) 3.20

Standard Pack 50 ft.

Stock (X) or Minimum Order Qty. 8 ea. (X)

Gates Item No. 3204-1721

Adapta Flex™ Black Cover Assemblies Nom. I.D. (In.) 3/8

(mm) 9.5

Nom. O.D. (In.) .66

(mm) 16.8

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 250

(MPa) 1.72

Suction (In. Hg) 30.0

Type P (EPDM). Black. Synthetic, high tensile textile cord. Type P (EPDM). Black. All sizes through 1/2 “ are perforated.

COUPLINGS:

19 (up through 1/2" only), 1, 3 or 4, (up through 1/2" with 20 brass ferrules, up through 1" with bands), 72 Gates Power Crimp® or 75 Gates GLX®. Reference the Hose Coupling Section.

PACKAGING:

Minimum of 90% of hose reels will be 1-piece lengths. 1/4" through 3/4": Packaged in 500' to 700' reels. Maximum 2 pieces in 50' increments. 3/8" x 50' coupled assemblies: Coiled in a carton, 5 assemblies per carton. 3/4" x 50': Packaged 200' per carton, each length coiled and tied. 1": Packaged in 300' to 400' reels. Maximum 2 pieces in 50' increments. 1 1/4": Packaged in 300' reels. Maximum 2 pieces in 50' increments. 1 1/2": Packaged in 250' reels. Maximum 2 pieces in 50' increments.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous ink brand. Example: “GATES® ADAPTA FLEX™ MULTI-PURPOSE 3/8 INCH (9.5mm) 250 PSI (1.72MPa) WP MADE IN USA” Special production runs require minimum order quantities of 25,000 feet per size. None. Tube: Cover:

RMA (Class C) Limited oil resistance. RMA (Class C) Limited oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 30

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Adapta Flex™ Blue, Green & Yellow Cover

Air and Multi-Purpose Hose

(Specification 3204BL, GR, YL)

Color Blue Blue Blue Blue Blue Blue Blue Blue Green Green Green Green Green Green Green Green Yellow Yellow Yellow Yellow Yellow Yellow Yellow Yellow

Nom. I.D. (In.) 1/4 3/8 3/8 1/2 1/2 3/4 3/4 3/4 1/4 3/8 3/8 1/2 1/2 3/4 3/4 3/4 1/4 3/8 3/8 1/2 1/2 3/4 3/4 3/4

(mm) 6.4 9.5 9.5 12.7 12.7 19.1 19.1 19.1 6.4 9.5 9.5 12.7 12.7 19.1 19.1 19.1 6.4 9.5 9.5 12.7 12.7 19.1 19.1 19.1

Nom. O.D. (In.) .50 .66 .69 .81 .83 1.15 1.15 1.15 .50 .66 .69 .81 .83 1.15 1.15 1.15 .50 .66 .69 .81 .83 1.15 1.15 1.15

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

(mm) 12.7 16.8 17.5 20.6 21.1 29.2 29.2 29.2 12.7 16.8 17.5 20.6 21.1 29.2 29.2 29.2 12.7 16.8 17.5 20.6 21.1 29.2 29.2 29.2

Max. W.P. (psi) 250 250 300 250 300 250 300 300 250 250 300 250 300 250 300 300 250 250 300 250 300 250 300 300

(MPa) 1.72 1.72 2.07 1.72 2.07 1.72 2.07 2.07 1.72 1.72 2.07 1.72 2.07 1.72 2.07 2.07 1.72 1.72 2.07 1.72 2.07 1.72 2.07 2.07

Suction (In. Hg) 30.0 30.0 30.0 25.0 25.0 20.0 15.0 15.0 30.0 30.0 30.0 25.0 25.0 20.0 15.0 15.0 30.0 30.0 30.0 25.0 25.0 20.0 15.0 15.0

(mm Hg) 762 762 762 635 635 508 381 381 762 762 762 635 635 508 381 381 762 762 762 635 635 508 381 381

Min. Bend Radius (In.) 3.0 3.0 3.0 5.0 5.0 6.0 6.0 6.0 3.0 3.0 3.0 5.0 5.0 6.0 6.0 6.0 3.0 3.0 3.0 5.0 5.0 6.0 6.0 6.0

(mm) 76 76 76 127 127 152 152 152 76 76 76 127 127 152 152 152 76 76 76 127 127 152 152 152

Wt. Per Ft. (Lbs.) .09 .14 .15 .19 .20 .35 .35 .35 .09 .14 .15 .19 .20 .35 .35 .35 .09 .14 .15 .19 .20 .35 .35 .35

(Kg) .04 .06 .07 .09 .09 .16 .16 .16 .04 .06 .07 .09 .09 .16 .16 .16 .40 .06 .07 .09 .09 .16 .16 .16

Standard Pack Reel Reel Reel Reel Reel Reel 50 ft. Reel Reel Reel Reel Reel Reel Reel 50 ft. Reel Reel Reel Reel Reel Reel Reel 50 ft. Reel

Stock (X) or Minimum Order Qty. 25,000 ft. X 25,000 ft. X 25,000 ft. X 200 ft. (X) X 25,000 ft. 25,000 ft. 25,000 ft. 25,000 ft. 25,000 ft. 25,000 ft. 200 ft. (X) X 25,000 ft. 25,000 ft. 25,000 ft. X 25,000 ft. 25,000 ft. 200 ft. (X) 25,000 ft.

Gates Item No. 3204-1496 3204-1497 3204-1501 3204-1498 3204-1503 3204-1500 3204-0560 3204-1505 3204-1516 3204-1517 3204-1511 3204-1518 3204-1513 3204-1520 3204-0506 3204-1515 3204-1526 3204-1527 3204-1521 3204-1528 3204-1523 3204-1530 3204-0558 3204-1525

Type P (EPDM). Black. Synthetic, high tensile textile cord. Type P (EPDM). Blue, Green or Yellow. All sizes through 1/2" are perforated.

COUPLINGS:

19 (up through 1/2" only), 1, 3 or 4, (up through 1/2" with 20 brass ferrules, up through 1" with bands), 72 Gates Power Crimp® or 75 Gates GLX®. Reference the Hose Coupling Section.

PACKAGING:

Minimum of 90% of hose reels will be 1-piece lengths. 3/8" through 3/4": Packaged in 500' to 700' reels. Maximum 2 pieces in 50' increments. 3/4" x 50': Packaged 200' per carton, each length coiled and tied.

BRANDING:

Continuous ink brand. Example: “GATES® ADAPTA FLEX™ MULTI-PURPOSE 3/8 INCH (9.5mm) 300 PSI (2.07MPa) WP MADE IN USA”

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Special production runs require minimum order quantities of 25,000 feet per size. None.

STANDARDS:

Tube:

RMA (Class C) Limited oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 31

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Tufflex® Plus

Air and Multi-Purpose Hose

(Specification 7746 Silicone Free) Nom. I.D. (In.) 1/4 3/8 1/2 5/8 3/4 1

(mm) 6.4 9.5 12.7 15.9 19.1 25.4

Nom. O.D. (In.) .50 .60 .79 .92 1.07 1.44

(mm) 12.7 15.2 20.1 23.4 27.2 36.6

Max. W.P. (psi) 300 300 300 300 300 200

(MPa) 2.07 2.07 2.07 2.07 2.07 1.38

Suction (In. Hg) 25.0 25.0 25.0 20.0 15.0 15.0

(mm Hg) 635 635 635 508 381 381

Min. Bend Radius (In.) .7 1.0 1.3 1.8 2.5 3.5

(mm) 18 25 33 46 64 89

Wt. Per Ft. (Lbs.) .11 .11 .13 .20 .29 .44

(Kg) .05 .05 .06 .09 .13 .20

Standard Pack Reel Reel Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X X X X

Gates Item No. 7746-1022 7746-1023 7746-1024 7746-1025 7746-1026 7746-1027

*Up through 3/4" 300 psi (2.07 MPa) at +70°F (+21°C), 250 psi (1.72 MPa) at +150°F (+66°C). For 1" 200 psi (1.38 MPa) at +70°F (+21°C), 150 psi (1.03 MPa) at 150°F (+66°C).

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Multi-purpose applications including air, water (up to 150°F), mild chemicals and spray solutions at rated working pressures as listed. Suitable for in-line oilier service. Silicone free. Ideal for pneumatic tools, air service to paint equipment, coolant lines, etc. Reference Gates Chemical Resistance Table for proper hose selection. -15°F to +150°F (-26°C to +66°C) continuous service. Tube: Reinforcement: Cover:

Type G1 (Modified PVC). Black. Synthetic, high tensile textile cord. Type G1 (Modified PVC). Red. All sizes are perforated.

COUPLINGS:

19 (up through 1/2" only), 1, 3 or 4, (up through 1/2" with 20 brass ferrules, up through 1" with bands), or 75 Gates GLX®. Reference the Hose Coupling Section.

PACKAGING:

1/4" through 5/8": Packaged on 500' reels. Maximum of 2 pieces per reel. 50' increments. 3/4": Packaged on 600' reels. Maximum of 2 pieces per reel. 50' increments. 1": Packaged on 400' reels. Maximum of 2 pieces per reel. 50' increments.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Continuous ink brand. Example: “GATES® Tufflex® Plus Multi-Purpose 1/2" (12.7mm) 300 PSI (2.07MPa) WP Made In U.S.A.” Additional colored covers are made to order and require minimum production order quantities of 25,000 feet per size. Special production runs require minimum order quantities of 25,000 feet per size. None.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 32

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

319MB Gold Master®

Air and Multi-Purpose Hose

(Specification 3619G/3619GL) Nom. I.D. (In.) 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2

(mm) 6.4 9.5 12.7 19.1 25.4 31.8 38.1 50.8

Nom. O.D. (In.) .63 .77 .92 1.21 1.46 1.69 1.94 2.46

(mm) 15.9 19.6 23.4 30.7 37.1 42.9 49.3 62.5

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 1000 1000 1000 1000 1000 1000 1000 1000

(MPa) 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90

Suction (In. Hg) 30.0 30.0 30.0 25.0 25.0 20.0 15.0 10.0

(mm Hg) 762 762 762 635 635 508 381 254

Min. Bend Radius (In.) 3.0 3.0 5.0 8.0 11.0 16.0 18.0 25.0

(mm) 76 76 127 203 279 406 457 635

Wt. Per Ft. (Lbs.) .22 .31 .42 .60 .77 .87 1.06 1.48

(Kg) .10 .14 .19 .27 .35 .40 .48 .67

Standard Pack Reel Reel Reel Reel 50 ft. 50 ft. 50 ft. 50 ft.

Stock (X) or Minimum Order Qty. 5,000 ft. 5,000 ft. 5,000 ft. 5,000 ft. 5,000 ft. 5,000 ft. 600 ft. 600 ft.

Gates Item No. 3619-0200 3619-0210 3619-0220 3619-0230 3619-0239 3619-0600 3619-0620 3619-0630

High-pressure water and oil applications requiring good kink resistance and excellent flexibility. Air service working pressure is 300 psi for all sizes. Also washdown service to 212°F (100°C) in packing plants where a nonmarking cover is required. Cover is resistant to weather, oil, animal fat, abrasion and heat encountered in packing plant cleaning applications. -40°F to +212°F (-40°C to +100°C) air service. Tube: Reinforcement: Cover:

Type A (Neoprene). Black. Braided, high tensile steel wire. Type M (Hypalon). Gold (non-marking). All sizes are perforated.

COUPLINGS:

72 Gates Power Crimp®, 14, 15, 18 (up to 300 PSI only) 74 Gates MegaCrimp®. Reference the Hose Coupling Section.

PACKAGING:

1/4" through 3/4": Packaged in 200' to 300' reels. Maximum of 3 pieces. Minimum length 25'. One length under 100'. 1" through 2": Packaged 50' coiled in a carton.

BRANDING:

Continuous transfer label. Example: “GATES® 319MB GOLD MASTER® MULTI-PURPOSE 3/8 INCH (9.5mm) 1000 PSI (6.90MPa) WP MADE IN U.S.A.”

SPECIAL ORDER REQUIREMENTS:

Special production runs require minimum order quantities of 5,000 feet for 1/4" through 1 1/4" and 600 feet for 1 1/2" and larger.

REMNANT LENGTHS: STANDARDS:

None. Tube: Cover:

RMA (Class B) Medium oil resistance. RMA (Class B) Medium oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 33

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

63SB (Air & Vapor Duct)

Air and Multi-Purpose Hose

(Specification 4663A) Nom. I.D. (In.) 5/8 3/4 7/8 1 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 2 2 1/8 2 1/4 2 3/8 2 1/2 2 5/8 2 3/4 3 3 1/2 3 5/8 4 4 1/2 5 5 1/2

(mm) 15.9 19.1 22.2 25.4 31.8 34.9 38.1 41.3 44.5 47.6 50.8 54.0 57.2 60.3 63.5 66.7 69.9 76.2 88.9 92.1 101.6 114.3 127.0 139.7

Nom. O.D. (In.) .81 .94 1.06 1.19 1.44 1.52 1.69 1.81 1.94 2.06 2.19 2.31 2.44 2.56 2.69 2.81 2.94 3.19 3.69 3.81 4.19 4.69 5.19 5.69

(mm) 20.6 23.9 26.9 30.2 36.6 38.6 42.9 46.0 49.3 52.3 55.6 58.7 62.0 65.0 68.3 71.4 74.7 81.0 93.7 96.8 106.4 119.1 131.8 144.5

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

PACKAGING: BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Max. W.P. (psi) 10 10 10 10 10 10 10 10 10 10 5 5 5 5 5 5 5 5 5 5 5 5 5 5

(MPa) .07 .07 .07 .07 .07 .07 .07 .07 .07 .07 .04 .04 .04 .04 .04 .04 .04 .04 .04 .04 .04 .04 .04 .04

Suction (In. Hg) 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0

(mm Hg) 127 127 127 127 127 127 127 127 127 127 76 76 76 76 76 76 76 76 76 76 76 76 76 76

Min. Bend Radius (In.) 1.0 1.0 1.0 1.0 1.0 1.5 1.5 2.0 2.0 2.0 2.0 2.5 2.5 2.5 2.5 2.8 2.8 3.0 3.5 4.0 4.0 5.0 6.0 6.0

(mm) 25 25 25 25 25 38 38 50 51 51 51 64 64 64 64 71 71 76 89 102 102 127 152 152

Wt. Per Ft. (Lbs.) .12 .14 .17 .20 .22 .24 .26 .28 .30 .32 .33 .35 .37 .39 .41 .43 .44 .49 .57 .59 .80 .89 .99 1.08

(Kg) .05 .06 .08 .09 .10 .11 .12 .13 .14 .15 .15 .16 .17 .18 .19 .20 .20 .22 .26 .27 .36 .40 .45 .49

Standard Pack 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft.

Stock (X) or Minimum Order Qty. X X X X X X X X X X X X X X X X X X X X X X X X

Gates Item No. 4663-4000 4663-4001 4663-4002 4663-4003 4663-4004 4663-4005 4663-4006 4663-4007 4663-4008 4663-4009 4663-4010 4663-4011 4663-4012 4663-4013 4663-4014 4663-4015 4663-4016 4663-4017 4663-4018 4663-4019 4663-4020 4663-4021 4663-4022 4663-4023

Heating and ventilating applications, such as air intake for butane conversion units, air and heater ducts, defroster lines, air cleaner connections to carburetor, exhaust ducts, vent lines for trailer sewers and drains. For standard duty applications. NOTE: Not recommended for conveying liquids. -30째F to +250째F (-34째C to +121째C) continuous service. Tube: Reinforcement: Cover:

Type A (Neoprene). Black. Oil resistant. Single ply of synthetic fabric with two built-in helical wires. Type A (Neoprene impregnated fabric). Black.

10' per carton. Printed patch label every 2 feet with I.D. only. Special production runs require minimum order quantities of one piece. Lengths can be as short as one foot, but minimum billing is ten feet. None.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 34

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

163SB (Air & Vapor Duct Heavy Duty)

Air and Multi-Purpose Hose

(Specification 4663J) Nom. I.D. (In.) 3/4 1 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 2 2 1/8 2 1/4 2 3/8 2 1/2 2 5/8 2 3/4 3 3 1/8 3 1/2 4 4 1/2 5 5 1/2 6

(mm) 19.1 25.4 31.8 34.9 38.1 41.3 44.5 47.6 50.8 54.0 57.2 60.3 63.5 66.7 69.9 76.2 79.4 88.9 101.6 114.3 127.0 139.9 152.4

Nom. O.D. (In.) 1.00 1.25 1.50 1.63 1.75 1.88 2.00 2.13 2.25 2.40 2.50 2.63 2.75 2.88 3.00 3.25 3.35 3.75 4.25 4.75 5.25 5.75 6.25

(mm) 25.4 31.8 38.1 41.4 44.5 47.8 50.8 54.1 57.2 61.0 63.5 66.8 69.9 73.2 76.2 82.6 85.1 95.3 108.0 120.7 133.4 146.1 158.8

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

PACKAGING: BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Max. W.P. (psi) 20 20 20 15 15 15 15 15 15 10 10 10 10 10 10 10 10 10 10 10 10 10 8

(MPa) .14 .14 .14 .10 .10 .10 .10 .10 .10 .07 .07 .07 .07 .07 .07 .07 .07 .07 .07 .07 .07 .07 .06

Suction (In. Hg) 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 7.0 7.0 7.0 7.0 7.0 6.0 6.0 6.0

(mm Hg) 381 381 381 381 381 381 381 381 381 381 381 381 381 381 381 178 178 178 178 178 152 152 152

Min. Bend Radius (In.) 1.0 1.0 1.0 1.5 1.5 1.8 1.8 1.8 2.0 2.5 2.5 2.5 2.5 3.0 7.0 10.0 10.0 10.0 12.0 12.0 12.0 12.0 15.0

(mm) 25 25 25 38 38 46 46 46 51 64 64 64 64 76 178 254 254 254 305 305 305 305 381

Wt. Per Ft. (Lbs.) .20 .26 .34 .44 .48 .51 .54 .58 .60 .74 .88 .71 .74 .78 .81 .88 .84 1.01 1.15 1.25 1.38 1.51 1.64

(Kg) .09 .12 .15 .20 .22 .23 .25 .26 .27 .34 .40 .32 .34 .35 .37 .40 .38 .46 .52 .57 .63 .69 .74

Standard Pack 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft.

Stock (X) or Minimum Order Qty. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft.

Gates Item No. 4663-1516 4663-1518 4663-1530 4663-3321 4663-1540 4663-1543 4663-3954 4663-1548 4663-1550 4663-3461 4663-1556 4663-1560 4663-1565 4663-1615 4663-3456 4663-1570 4663-1569 4663-1575 4663-1580 4663-1589 4663-1595 4663-3454 4663-1599

Heavy-duty heating and ventilating applications, such as air intake for butane conversion units, air and heater ducts, defroster lines, air cleaner connections to carburetor, exhaust ducts, vent lines for trailer sewers and drains. NOTE: Not recommended for conveying liquids. -30°F to +250°F (-34°C to +121°C) continuous service. Tube: Reinforcement: Cover:

Type A (Neoprene). Black. Oil and heat resistant. Single ply of synthetic fabric with two built-in helical wires. Type A (Neoprene). Black. Oil and heat resistant.

10' per carton. Printed patch label every 2 feet with I.D. only. For enlarged or straight ends, contact Gates Corporation for pricing. Special production runs require minimum order quantities of one piece. Lengths can be as short as one foot, but minimum billing is ten feet. None.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 35

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Ohmega® (Pot Room)

Air and Multi-Purpose Hose

(Specification 3237A) Nom. I.D. (In.) 3/8 1/2 3/4

(mm) 9.5 12.7 19.1

Nom. O.D. (In.) .75 .88 1.16

(mm) 19.1 22.4 29.5

Max. W.P. (psi) 300 300 300

(MPa) 2.07 2.07 2.07

Suction (In. Hg) 30.0 25.0 20.0

(mm Hg) 762 635 508

Min. Bend Radius (In.) 3.0 5.0 6.0

(mm) 76 127 152

Wt. Per Ft. (Lbs.) .19 .24 .36

(Kg) .09 .11 .16

Standard Pack Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X

Gates Item No. 3237-0704 3237-0705 3237-0706

NOTE: For additional sizes see Premo Flex®.

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Medium duty air and water applications where a hose with high electrical resistance is needed. -20°F to +150°F (-29°C to +66°C) continuous service. Tube: Reinforcement: Cover:

Type P (EPDM). Green. High tensile synthetic textile cord. Type P (EPDM). Red.

COUPLINGS:

19 (For sizes 3/16" through 3/8" only), 1, 18 or 75 Gates GLX®. Reference the Hose Coupling Section.

PACKAGING:

3/8" through 3/4": Packaged in 500' to 750' reels. Maximum 3 pieces. Minimum length 50'.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous ink print label. Example: “GATES® OMEGA® AIR AND WATER 3/8 INCH (9.5mm) 300 PSI (2.07MPa) WP NONCONDUCTIVE @ 1000 V DC (>1 MEGOHM/IN.) MADE IN USA” Special production runs require minimum order quantities of 25,000 feet per size. None. Nonconductive at 1000 volts D.C. Electrical resistance is greater than one megohm per inch when subjected to 1000 volts D.C. Storage and use may adversely affect electrical properties.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 36

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

33HB (Divers’ Air)

Air and Multi-Purpose Hose

(Specification 3333) Nom. I.D. (In.) 3/8 3/8 1/2 1/2

Nom. O.D. (In.) .75 .75 .94 .94

(mm) 9.5 9.5 12.7 12.7

(mm) 19.1 19.1 23.9 23.9

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 1125 1125 1000 1000

(MPa) 7.76 7.76 6.90 6.90

Suction (In. Hg) 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762

Min. Bend Radius (In.) 4.0 4.0 5.0 5.0

(mm) 102 102 127 127

Wt. Per Ft. (Lbs.) .19 .19 .29 .29

(Kg) .09 .09 .13 .13

Standard Pack 600-699 ft. 1000-Plus ft. 50-299 ft. 1000-Plus ft.

-40°F to +120°F (-40°C to +49°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Braided, high tensile synthetic textile cord. Type A (Neoprene). Black. All sizes are perforated.

COUPLINGS:

Corrosion resistant couplings supplied and applied by diving contractors. 3/8" and 1/2": Packaged 300' and longer lengths. One continuous length on a reel.

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Gates Item No. 3333-0015 3333-0017 3333-0038 3333-0035

Handling mixtures of oxygen, helium and nitrogen gases customarily used in diving applications as air breathing hose. The kink resistant hose is designed for extra long wear under normal operating use.

PACKAGING: BRANDING:

Stock (X) or Minimum Order Qty. X X X X

Continuous ink print label. Example: “GATES® 33HB DIVERS” AIR 3/8 INCH (9.5mm) MADE IN U.S.A.’ Contact Gates Corporation for special orders. Special production runs require minimum order quantities of 10,000 feet per size. Special production runs for SPECIFIC LENGTHS require minimum order quantities of 10,000 feet per size and a 35% (x 1.35) premium to price. None. Meets MIL-H-2815G Section 3.12.2 off-gassing for air breathing applications, especially diving.

33HB Divers’ Air Hose Couplings Ferrule Size 3/8

Description 33HB-6-FRLB

Gates Item No. 7207-0597

Stock (X) or Minimum Order Qty. 50 ea. (X)

Stems Size Description Gates Item No. Stock (X) or Minimum Order Qty. 3/8 33HB-6-6RFJX-STB 7207-0598 50 ea. (X) 3/8 33HB-6-6ROXY-STB 7207-0599 50 ea. (X) NOTE: These couplings are to be used with 33HB Divers’ Air hose only. 33HB assemblies made with Gates Divers’ air couplings are rated at 250 PSI maximum working pressure.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 37

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Food & Beverage Master®

Food and Beverage Hose

(Specification 3132C/3132H) White Cover (3132C) Nom. I.D. (In.) 3/4 1 1 1/2 2 2 1/2 3 4

(mm) 19.1 25.4 38.1 50.8 63.5 76.2 101.6

Nom. O.D. (In.) 1.22 1.48 2.07 2.62 3.25 3.86 4.88

(mm) 31.0 37.6 52.6 66.6 82.6 98.0 124.0

Max. W.P. (psi) 250 250 250 250 250 250 250

(MPa) 1.72 1.72 1.72 1.72 1.72 1.72 1.72

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(MPa) 1.72 1.72 1.72 1.72 1.72 1.72 1.72 1.72 1.72

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762

Min. Bend Radius (In.) 2.0 3.0 4.5 6.0 12.0 18.0 36.0

(mm Hg) 762 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 2.0 3.0 4.5 4.5 6.0 12.0 12.0 18.0 36.0

(mm) 51 76 114 152 305 457 914

Wt. Per Ft. (Lbs.) .42 .52 .90 1.19 1.81 2.46 3.24

(mm) 51 76 114 114 152 305 305 457 914

Wt. Per Ft. (Lbs.) .42 .52 .90 .90 1.20 1.81 1.81 2.47 3.24

(Kg) .19 .24 .41 .54 .82 1.12 1.47

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. X X X X X X X

Gates Item No. 3132-0222 3132-0216 3132-0217 3132-0218 3132-0219 3132-0220 3132-0221

(Kg) .19 .24 .41 .41 .54 .82 .82 1.12 1.47

Standard Pack 100 ft. 100 ft. 200 ft. 100 ft. 100 ft. 200 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. 400 ft. 400 ft. 400 ft. 400 ft. 400 ft. 400 ft. 400 ft. 400 ft. 400 ft.

Gates Item No. 3132-0263 3132-0264 3132-0066 3132-0265 3132-0266 3132-0067 3132-0267 3132-0268 3132-0269

Gray Cover (3132H) Nom. I.D. (In.) 3/4 1 1 1/2 1 1/2 2 2 1/2 2 1/2 3 4

(mm) 19.1 25.4 38.1 38.1 50.8 63.5 63.5 76.2 101.6

Nom. O.D. (In.) 1.22 1.48 2.07 2.07 2.62 3.25 3.25 3.86 4.88

(mm) 31.0 37.6 52.6 52.6 66.6 82.6 82.6 98.0 124.0

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 250 250 250 250 250 250 250 250 250

Transfer of milk, juice, soft drinks, pharmaceuticals, cosmetics or water-based products requiring an FDA sanitary hose. Food & Beverage Master is also suitable for many dry bulk products via suction, pneumatic or gravity where a sanitary hose is required. -40°F to +230°F (-40°C to +110°C) continuous service. Tube: Reinforcement: Cover:

Type S (Sanitron™). White. Synthetic, high tensile textile with static conductive filament; resilient monofilament helix providing crush and kink resistance. Type P (EPDM). White or gray with burgundy spiral stripe.

COUPLINGS:

1 or stainless steel, 8 or stainless steel, 34, 71. Reference the Hose Coupling Section.

PACKAGING:

100' coiled and wrapped in polyethylene.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous transfer label. Example: “GATES® Food & Beverage Master® Meets FDA, 3A and USDA 250 PSI WP (1.72MPa) Made In U.S.A.” Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Meets FDA requirements, 3A-Class 3 and USDA.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 38

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Cellar Master®

Food and Beverage Hose

(Specification 3132C) Nom. I.D. (In.) 1 1 1/2 2 2 1/2 3 4

(mm) 25.4 38.1 50.8 63.5 76.2 101.6

Nom. O.D. (In.) 1.48 2.07 2.62 3.25 3.86 4.88

(mm) 37.6 52.6 66.6 82.6 98.0 124.0

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 250 250 250 250 250 250

(MPa) 1.72 1.72 1.72 1.72 1.72 1.72

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762

Min. Bend Radius (In.) 3.0 4.5 6.0 12.0 18.0 36.0

(mm) 76 114 152 305 457 914

Wt. Per Ft. (Lbs.) .52 .90 1.20 1.81 2.46 3.24

(Kg) .24 .41 .54 .82 1.12 1.47

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft.

-40°F to +230°F (-40°C to +110°C) continuous service. Tube: Reinforcement: Cover:

Type S (Sanitron™). White. Synthetic, high tensile textile with resilient monofilament helix providing crush and kink resistance. Type P (EPDM). White with burgundy spiral stripe.

1 or stainless steel, 8 or stainless steel, 34, 71. Reference the Hose Coupling Section.

PACKAGING:

100' length coiled and wrapped in polyethylene.

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Gates Item No. 3132-0180 3132-0181 3132-0182 3132-0186 3132-0183 3132-0184

Wine or water based products requiring an FDA sanitary hose.

COUPLINGS:

BRANDING:

Stock (X) or Minimum Order Qty. 200 ft. 200 ft. 200 ft. 200 ft. 200 ft. 200 ft.

Continuous transfer label. Example: “GATES® Cellar Master® Meets FDA, 3A and USDA 250 PSI (1.72MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Meets FDA requirements, 3A-Class 3 and USDA.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 39

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Cellar Master® Light

Food and Beverage Hose

(Specification 3132LW) Nom. I.D. (In.) (mm) 1 1/2 38.1 2 50.5 2 1/2 63.5 3 76.2 4 101.6 *Working Pressure

Nom. Max. Min. Bend O.D. W.P. Radius Suction (In.) (mm) (psi) (MPa) (In. Hg) (mm Hg) (In.) (mm) 2.00 50.8 150 1.03 30.0 762 6.0 152 2.50 63.5 150 1.03 30.0 762 12.0 305 3.11 79.0 150 1.03 30.0 762 22.0 559 3.75 95.3 150 1.03 30.0 762 20.0 508 4.76 120.9 150 1.03 30.0 762 28.0 711 and Suction at +72°F (+22°C). Suction rating reduced at elevated temperatures.

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Wt. Per Ft. (Lbs.) .77 .96 1.53 2.13 2.82

(Kg) .35 .44 .69 .97 1.28

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft.

-40°F to +212°F (-40°C to +100°C) continuous service. Tube: Reinforcement: Cover:

Type S (Sanitron™). White. Synthetic, high tensile textile with resilient monofilament helix providing crush and kink resistance. Type P (EPDM). Gray with maroon spiral stripe.

1 or stainless steel, 8 or stainless steel, 34, 71. Reference the Hose Coupling Section.

PACKAGING:

100' length coiled and wrapped in polyethylene.

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Gates Item No. 3132-0171 3132-0172 3132-0173 3132-0174 3132-0175

Wine or water based products requiring an FDA sanitary hose.

COUPLINGS:

BRANDING:

Stock (X) or Minimum Order Qty. 200 ft. X 200 ft. 200 ft. 200 ft.

Continuous transfer label. Example: “GATES® Cellar Master® Light Meets FDA, 3A and USDA 150 PSI (1.03MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Meets FDA requirements, 3A-Class 3 and USDA.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 40

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Food Master® Lite™

Food and Beverage Hose

(Specification 3133) Nom. I.D. (In.) 3/4 1 1 1/2 2 2 1/2 3 4 6

(mm) 19.1 25.4 38.1 50.8 63.5 76.2 101.6 152.4

Nom. O.D. (In.) 1.33 1.58 2.10 2.60 3.13 3.63 4.65 6.74

(mm) 33.8 40.1 53.3 66.0 79.5 92.2 118.1 171.2

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 150 150 150 150 150 150

(MPa) 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 2.0 3.0 4.5 6.0 12.0 18.0 24.0 36.0

(mm) 51 76 114 152 305 457 610 914

Wt. Per Ft. (Lbs.) .65 .79 1.14 1.50 1.98 2.35 3.12 5.60

(Kg) .30 .36 .52 .68 .90 1.07 1.42 2.54

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 50 ft.

-40°F to +230°F (-40°C to +110°C) continuous service. Tube: Reinforcement: Cover:

Type C2 (Modified Nitrile). Sanitary FDA and 3A-Class 3. White. Synthetic, high tensile textile with steel wire helix. Type C2 (Modified Nitrile). White corrugated with burgundy spiral stripe.

COUPLINGS:

1 or stainless steel, 8 or stainless steel, 34, 71. Reference the Hose Coupling Section. All lengths coiled and wrapped in polyethylene.

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Gates Item No. 3133-0001 3133-0002 3133-0003 3133-0004 3133-0005 3133-0006 3133-0007 3133-0008

Tank truck, barge, ship, or storage tank transfer of a variety of food products such as animal fat, vegetable oil and other edible oils at temperatures up to 230°F requiring FDA sanitary hose. Also suitable for ice cream and other dairy products requiring 3A-Class 3 standards.

PACKAGING: BRANDING:

Stock (X) or Minimum Order Qty. X X X X X X X X

Continuous transfer label. Example: “GATES® Food Master® Lite™ Meets FDA, 3A and USDA 150 PSI (1.03MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet for sizes through 4" and 200 feet for sizes above 4". If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube meets FDA requirements, 3A-Class 3 and USDA.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 41

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Sani-Pure™

Food and Beverage Hose

(Specification 3131) Nom. I.D. (In.) 1 1/2 2 2 1/2 3 4 6

(mm) 38.1 50.8 63.5 76.2 101.6 152.4

Nom. O.D. (In.) 2.07 2.57 3.08 3.58 4.61 6.64

(mm) 52.6 65.3 78.2 90.9 117.1 168.7

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 150 150 150 150

(MPa) 1.03 1.03 1.03 1.03 1.03 1.03

Suction (In. Hg) — — — — — —

(mm Hg) — — — — — —

Min. Bend Radius (In.) 18.0 24.0 30.0 36.0 48.0 72.0

(mm) 457 610 762 914 1219 1829

Wt. Per Ft. (Lbs.) .97 1.25 1.65 1.90 2.77 4.10

(Kg) .44 .57 .75 .86 1.26 1.86

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 50 ft.

-40°F to +230°F (-40°C to +110°C) continuous service. Tube: Reinforcement: Cover:

Type C2 (Modified Nitrile). Sanitary FDA and 3A-Class 3. White. Synthetic, high tensile textile. Type C2 (Modified Nitrile). White with burgundy spiral stripe.

1 or stainless steel, 8 or stainless steel, 34, 71. Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled and wrapped in polyethylene.

SPECIAL ORDER REQUIREMENTS:

REMNANT LENGTHS: STANDARDS:

Gates Item No. 3131-0001 3131-0002 3131-0003 3131-0004 3131-0005 3131-0006

Tank truck, barge, ship, or storage tank transfer (discharge only) of a variety of food products such as animal fat, vegetable oil and other edible oils at temperatures up to 230°F requiring FDA sanitary hose. Also suitable for ice cream and other dairy products requiring 3A-Class 3 standards.

COUPLINGS:

BRANDING:

Stock (X) or Minimum Order Qty. 200 ft. X 200 ft. 200 ft. 200 ft. 200 ft.

Continuous transfer label. Example: “GATES® Sani-Pure™ Meets FDA, 3A and USDA 150 PSI (1.03MPa) WP Made in U.S.A.” Gray cover is made to order and requires minimum production order quantities of 400 feet for sizes through 4" and 200 feet for sizes above 4". For price, add 10% (x1.10) to price. Special production runs require minimum order quantities of 400 feet for sizes through 4" and 200 feet for sizes above 4". If a special transfer label is required, contact Gates Corporation for minimum quantity. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube meets FDA requirements, 3A-Class 3 and USDA.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 42

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Aquarius® Potable Water

Food and Beverage Hose

(Specification 3132P) Nom. I.D. (In.) 1 2 3 4

(mm) 25.4 51.0 76.0 102.0

Nom. O.D. (In.) 1.53 2.70 3.70 4.70

(mm) 38.9 68.6 94.0 119.0

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 300 300 200 150

(MPa) 2.07 2.07 1.38 1.03

Suction (In. Hg) 15.0 10.0 10.0 10.0

(mm Hg) 381 254 254 254

Min. Bend Radius (In.) 10.0 14.0 21.0 28.0

(mm) 254 356 533 711

200' length coiled and wrapped in polyethylene.

STANDARDS:

Gates Item No. 3132-0803 3132-0815 3132-0823 3132-0832

Type D2 (food Grade Natural Rubber). White. Multiple plies of synthetic cord. Type P (EPDM). Tan with green spiral stripe. Abrasion and weather resistant.

14, 15, 71 or 8. Reference the Hose Coupling Section.

REMNANT LENGTHS:

Stock (X) or Minimum Order Qty. 400 ft. 400 ft. 400 ft. 400 ft.

-40°F to +150°F (-40°C to +66°C) continuous service. Tube: Reinforcement: Cover:

COUPLINGS:

SPECIAL ORDER REQUIREMENTS:

(Kg) .28 .66 .95 1.23

Standard Pack 200 ft. 200 ft. 200 ft. 200 ft.

Transfer of potable water, non-potable water or liquids not containing oils or chemicals from a supply ship to an offshore drilling rig or platform and for transfer applications on offshore or onshore drilling rigs or platforms; applications which require a lightweight, flexible hose with a tight bend radius and a high rated working pressure in long continuous lengths.

PACKAGING: BRANDING:

Wt. Per Ft. (Lbs.) .61 1.46 2.15 2.70

Continuous transfer label. Example: “GATES® Aquarius® Potable Water meets FDA stds. 200 PSI (1.38MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. None. Tube meets FDA requirements.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 43

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

690SB (Bulk Commodity)

Food and Beverage Hose

(Specification 4693B) Nom. I.D. (In.) 1 1/2 2 2 1/2 3 4 5 6

(mm) 38.1 50.8 63.5 76.2 101.6 127.0 152.4

Nom. O.D. (In.) 2.23 2.75 3.23 3.75 4.71 5.75 6.91

(mm) 56.6 69.9 82.0 95.3 119.6 146.0 175.5

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 125 100 75 55 50

(MPa) 1.03 1.03 .86 .69 .52 .38 .34

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762

Min. Bend Radius (In.) 10.0 12.0 15.0 18.0 24.0 30.0 36.0

(mm) 254 305 381 457 610 762 914

Wt. Per Ft. (Lbs.) 1.41 1.88 2.25 2.73 3.51 4.30 7.08

(Kg) .64 .85 1.02 1.24 1.59 1.95 3.21

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 50 ft. 50 ft.

Stock (X) or Minimum Order Qty. X X X X X X X

Transfer of bulk food products via suction, pneumatic or gravity systems where FDA sanitary tube is required. Examples: Flour, sugar, syrup and edible grains. (Not recommended for vinegar, mustard or other compounds containing acetic acid.) -40°F to +150°F (-40°C to +66°C) continuous service. Tube: Reinforcement: Cover:

Type D2 (Natural Rubber). Sanitary FDA. White. 3/16" thick. Synthetic, high tensile textile with steel wire helix. Type D3 (Natural Rubber). Gray corrugated with burgundy spiral stripe.

COUPLINGS:

*Can be used only at 50% of rated working pressure. Reference the Hose Coupling Section. 5*, 6*, 7*, 8, 49, or 71. Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled and wrapped in polyethylene.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Gates Item No. 4693-0205 4693-0210 4693-0220 4693-0225 4693-0235 4693-0251 4693-0260

Continuous transfer label. Example: “GATES® 690SB Food-Beverage Transfer Meets FDA 100 PSI. (.69MPa) 3/16 Inch Tube Made in U.S.A.” Special production runs require minimum order quantities of 400 feet for sizes through 4" and 200 feet for sizes above 4". Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube meets FDA requirements.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 44

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

692SB (Bulk Commodity)

Food and Beverage Hose

(Specification 4693R) Nom. I.D. (In.) 1 1/2 2 2 1/2 3 4 6

(mm) 38.1 50.8 63.5 76.2 101.6 152.4

Nom. O.D. (In.) 2.07 2.60 2.85 3.52 4.55 6.74

(mm) 52.6 66.0 72.4 89.4 115.6 171.2

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 125 125 75 50

(MPa) 1.03 1.03 .86 .86 .52 .34

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 25.0

(mm Hg) 762 762 762 762 762 635

Min. Bend Radius (In.) 9.0 12.0 15.0 18.0 24.0 36.0

(mm) 229 305 381 457 610 914

Wt. Per Ft. (Lbs.) 1.13 1.46 1.77 2.20 2.96 5.61

(Kg) .51 .66 .80 1.00 1.34 2.54

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 50 ft.

Stock (X) or Minimum Order Qty. 400 ft. X 400 ft. X X 200 ft.

Animal fat, vegetable oil and other edible oils at temperatures up to 180°F requiring FDA sanitary hose. Also for soybeans, vinegar, mustard, cider, salad dressings and other acetic acid applications. -40°F to +180°F (-40°C to +82°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Sanitary FDA. White. 1/8" thick. Synthetic, high tensile textile with steel wire helix. Type P (EPDM). Tan corrugated with burgundy spiral stripe.

COUPLINGS:

*Can be used only at 50% of rated working pressure. Reference the Hose Coupling Section. 5*, 6*, 7*, 8, 49, or 71. Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled and wrapped in polyethylene.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Gates Item No. 4693-0105 4693-0110 4693-0116 4693-0125 4693-0135 4693-0160

Continuous transfer label. Example: “GATES® 692SB Edible Fats-Oils Transfer Meets FDA 125 PSI (.86MPa) Made In U.S.A.” Special production runs require minimum order quantities of 400 feet for sizes through 4" and 200 feet for sizes above 4". Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube meets FDA requirements, 3A Standards and USDA.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 45

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

610W (Bulk Commodity)

Food and Beverage Hose

(Specification 3132D) Nom. I.D. (In.) 4 5 6

(mm) 101.6 127.0 152.4

Nom. O.D. (In.) 4.56 5.56 6.56

(mm) 115.8 141.2 166.6

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 40 30 25

(MPa) .28 .21 .17

Suction (In. Hg) — — —

(mm Hg) — — —

Min. Bend Radius (In.) 48.0 60.0 72.0

(mm) 1219 1524 1829

Wt. Per Ft. (Lbs.) 2.22 2.73 3.25

(Kg) 1.01 1.24 1.47

Standard Pack 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. X X X

Gates Item No. 3132-0782 3132-0793 3132-0797

Pneumatic transfer of flour and other dry foods requiring hose with a sanitary FDA tube. -40°F to +150°F (-40°C to +66°C) continuous service. Tube: Reinforcement: Cover:

Type D2 (Natural Rubber). Sanitary FDA. White. 3/16" thick. Synthetic, high tensile textile with static conductor. Type D3 (Natural Rubber). Gray with burgundy spiral stripe.

COUPLINGS:

5, 7, 49 or 71. Reference the Hose Coupling Section.

PACKAGING:

100' length coiled and wrapped in polyethylene.

BRANDING:

Continuous transfer label. Example: “GATES® 610W Dry Food Transfer Meets FDA 40 PSI (.28MPa) WP Made In U.S.A.”

SPECIAL ORDER REQUIREMENTS:

Special production runs require minimum order quantities of 400 feet for sizes through 4" and 200 feet for sizes above 4". If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details.

REMNANT LENGTHS: STANDARDS:

Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube meets FDA requirements.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 46

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Master-Flex® 200CL

Food and Beverage Hose

(Specification 7744) Nom. I.D. (In.) (mm) 1 25.4 1 1/4 31.8 1 1/2 38.1 2 50.8 2 1/2 63.5 3 76.2 4 101.6 *Working Pressure

Nom. Max. O.D. W.P. (In.) (mm) (psi) (MPa) 1.29 32.8 100 .69 1.56 39.6 90 .62 1.84 46.7 90 .62 2.39 60.7 70 .48 2.92 74.2 65 .45 3.46 87.9 60 .41 4.56 115.8 50 .34 and Suction at +72°F (+22°C).

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Suction (In. Hg) 28.0 28.0 28.0 28.0 28.0 28.0 28.0

(mm Hg) 711 711 711 711 711 711 711

Min. Bend Radius (In.) 3.0 4.0 5.0 6.0 8.0 9.0 12.0

Gates Item No. 7744-4101 7744-4102 7744-4103 7744-4104 7744-4105 7744-4106 7744-4107

Type G (PVC). Sanitary FDA. Clear. Smooth. Rigid thermoplastic reinforcement. Clear. Type G (PVC). Sanitary FDA. Clear. Smooth.

1, 6, 7 or 49. Reference the Hose Coupling Section. All lengths coiled and wrapped in polyethylene.

STANDARDS:

Stock (X) or Minimum Order Qty. X X X X X X X

-10°F to +130°F (-23°C to +55°C) continuous service. Tube: Reinforcement: Cover:

COUPLINGS:

BRANDING:

(Kg) .14 .17 .22 .32 .44 .58 .91

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft.

Transfer of bulk food products via suction, pneumatic or gravity systems where sanitary hose is required.

PACKAGING:

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

(mm) 76 102 127 152 203 229 305

Wt. Per Ft. (Lbs.) .30 .38 .48 .71 .97 1.27 2.01

Unlabeled. None. None. Meets FDA requirements, 3A Standards and USDA.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 47

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Master-Flex® 201CR

Food and Beverage Hose

(Specification 7744) Nom. I.D. (In.) (mm) 1 25.4 1 1/4 31.8 1 1/2 38.1 2 50.8 2 1/2 63.5 3 76.2 4 101.6 *Working Pressure

Nom. Max. O.D. W.P. (In.) (mm) (psi) (MPa) 1.26 32.0 40 .28 1.61 40.9 50 .34 1.82 46.2 50 .34 2.44 62.0 40 .28 2.98 75.7 40 .28 3.54 89.9 35 .24 4.65 118.1 35 .24 and Suction at +72°F (+22°C).

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Suction (In. Hg) 28.0 28.0 28.0 28.0 28.0 28.0 28.0

(mm Hg) 711 711 711 711 711 711 711

Min. Bend Radius (In.) 2.0 3.0 3.0 4.0 5.0 6.0 8.0

Tube: Reinforcement: Cover:

Gates Item No. 7744-4301 7744-4302 7744-4303 7744-4304 7744-4305 7744-4306 7744-4307

Type G (PVC). Sanitary FDA. Clear. Smooth. Rigid thermoplastic helix. Clear. Type G (PVC). Sanitary FDA. Clear. Corrugated.

1, 6, 7 or 49. Reference the Hose Coupling Section. All lengths coiled and wrapped in polyethylene.

STANDARDS:

Stock (X) or Minimum Order Qty. X X X X X X X

-10°F to +130°F (-23°C to +55°C) continuous service.

COUPLINGS:

BRANDING:

(Kg) .06 .14 .17 .26 .35 .47 .75

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft.

Transfer of bulk food products via suction, pneumatic or gravity systems where sanitary hose is required.

PACKAGING:

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

(mm) 51 76 76 102 127 152 203

Wt. Per Ft. (Lbs.) .14 .31 .37 .57 .77 1.04 1.65

Unlabeled. None. None. Meets FDA requirements and USDA.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 48

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Master-Flex® 202SW

Food and Beverage Hose

(Specification 7744) Nom. I.D. (In.) (mm) 2 50.8 2 1/2 63.5 3 76.2 4 101.6 *Working Pressure

Nom. Max. O.D. W.P. (In.) (mm) (psi) (MPa) 2.37 60.2 40 .28 3.01 76.5 40 .28 3.05 77.5 35 .24 4.54 115.3 35 .24 and Suction at +72°F (+22°C).

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Suction (In. Hg) 28.0 28.0 28.0 28.0

(mm Hg) 711 711 711 711

Min. Bend Radius (In.) 4.0 4.0 6.0 8.0

Gates Item No. 7744-4420 7744-4425 7744-4430 7744-4440

Type G (PVC). Sanitary FDA. Clear. Smooth. Rigid thermoplastic helix. Clear. Embedded static wire to prevent a build up of static electricity. Type G (PVC). Sanitary FDA. Clear. Corrugated.

PACKAGING:

All lengths coiled and wrapped in polyethylene.

STANDARDS:

Stock (X) or Minimum Order Qty. X X X X

-10°F to +130°F (-23°C to +55°C) continuous service. Tube: Reinforcement: Cover:

1, 6, 7 or 49. Reference the Hose Coupling Section.

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

(Kg) .26 .36 .48 .76

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft.

Transfer of bulk food products via suction, pneumatic or gravity systems where sanitary hose is required. Used in pneumatic conveying systems for powders, pellets or granular materials where a static conductive hose is needed.

COUPLINGS:

BRANDING:

(mm) 102 102 152 203

Wt. Per Ft. (Lbs.) .58 .79 1.06 1.68

Unlabeled. None. None. Meets FDA requirements and USDA.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 49

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Tufflex® Food

Food and Beverage Hose

(Specification 7744) Nom. I.D. (In.) 1/4 3/8 1/2 5/8 3/4 1 1 1/4 1 1/2 2

(mm) 6.4 9.5 12.7 15.9 19.1 25.4 31.8 38.1 50.8

Nom. O.D. (In.) .47 .63 .75 .88 1.03 1.31 1.75 2.00 2.50

(mm) 11.9 16.0 19.1 22.4 26.2 33.3 44.5 50.8 63.5

Max. W.P. (psi) 250 200 200 200 150 125 100 75 75

(MPa) 1.72 1.38 1.38 1.38 1.03 .86 .69 .52 .52

Suction (In. Hg) — — — — — — — — —

(mm Hg) — — — — — — — — —

Min. Bend Radius (In.) — — — — — — — — —

(mm) — — — — — — — — —

Wt. Per Ft. (Lbs.) .07 .11 .13 .15 .20 .32 .63 .74 .95

(Kg) .03 .05 .06 .07 .09 .15 .29 .34 .43

Standard Pack 300 ft. 300 ft. 300 ft. 300 ft. 300 ft. 100 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. X X X X X X 1,000 ft. 1,000 ft. 1,000 ft.

Gates Item No. 7744-4501 7744-4502 7744-4503 7744-4504 7744-4505 7744-4506 7744-4507 7744-4508 7744-4509

*Working Pressure and Suction at +72°F (+22°C).

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Transferring compressed liquid and air in food and beverage applications. Approved for use in USDA meat and poultry plants. Non-toxic, FDA formula approved for food processing. Also suitable for potable water transfer. -10°F to +130°F (-23°C to +55°C) continuous service. Tube: Reinforcement: Cover:

Type G (PVC). Non-toxic. Clear. Synthetic reinforcement. Type G (PVC). Non-toxic. Clear. Smooth.

COUPLINGS:

Stainless Steel Food Grade.

PACKAGING:

All lengths coiled and wrapped in polyethylene.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

“Made In Japan” Special production runs require minimum order quantities of 1,000 feet per size. No deviations allowed to above product. None. Meets FDA requirements and USDA.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 50

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

75W (Standard Wall Coolant)

Marine Hose

(Specification 4175EC) Nom. I.D. (In.) 3/4 7/8 1 1 1/8 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 2 2 1/8 2 1/4 2 3/8 2 1/2 2 5/8 2 3/4 2 7/8 3 3 1/2 4 4 1/2

(mm) 19.1 22.2 25.4 28.6 31.8 34.9 38.1 41.3 44.5 47.6 50.8 54.0 57.2 60.3 63.5 66.7 69.9 73.0 76.2 88.9 101.6 114.3

Nom. O.D. (In.) 1.17 1.25 1.38 1.50 1.63 1.75 1.88 2.00 2.13 2.25 2.39 2.51 2.64 2.76 2.89 3.02 3.14 3.26 3.39 3.89 4.39 4.89

(mm) 29.7 31.8 35.1 38.1 41.4 44.5 47.8 50.8 54.1 57.2 60.7 63.8 67.1 70.1 73.4 76.7 79.8 82.8 86.1 98.8 111.5 124.2

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 80 75 140 125 100 100 100 90 75 75 60 60 60 60 60 60 60 60 50 20 12 12

(MPa) .55 .52 .97 .86 .69 .69 .69 .62 .52 .52 .41 .41 .41 .41 .41 .41 .41 .41 .34 .14 .08 .08

Suction (In. Hg) 5.0 7.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 — — — — — — — — — — — — —

(mm Hg) 127 178 178 152 127 102 76 51 25 — — — — — — — — — — — — —

Min. Bend Radius (In.) 6.0 7.0 8.0 8.0 12.0 12.0 12.0 15.0 15.0 — — — — — — — — — — — — —

Tube: Reinforcement: Cover:

50' length coiled and wrapped in polyethylene. 50' carton: 7/8" through 1" sizes only.

STANDARDS:

Gates Item No. 4175-0855 4175-0856 4175-0857 4175-0859 4175-0861 4175-0863 4175-0865 4175-0867 4175-0869 4175-0871 4175-0872 4175-0873 4175-0874 4175-0875 4175-0876 4175-0877 4175-0878 4175-0879 4175-0880 4175-0883 4175-0886 4175-0889

Type P (EPDM). Black. Multiple plies of synthetic fabric. Type P (EPDM). Black with white spiral stripe. Heat and ozone resistant.

PACKAGING:

REMNANT LENGTHS:

Stock (X) or Minimum Order Qty. X X X X X 400 ft. X X X X X 400 ft. X X X 400 ft. X 400 ft. X X X X

-40°F to +257°F (-40°C to +125°C) continuous service.

5, 6 or 7. Reference the Hose Coupling Section.

SPECIAL ORDER REQUIREMENTS:

(Kg) .17 .18 .19 .21 .23 .25 .23 .29 .30 .33 .35 .36 .38 .40 .42 .44 .45 .47 .50 .57 .65 .73

Standard Pack 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft.

Open end water discharge applications and coolant connections on marine and stationary engines.

COUPLINGS:

BRANDING:

(mm) 152 178 203 203 305 305 305 381 381 — — — — — — — — — — — — —

Wt. Per Ft. (Lbs.) .37 .39 .42 .47 .51 .55 .51 .63 .67 .72 .76 .79 .84 .88 .92 .96 1.00 1.04 1.10 1.26 1.43 1.60

Continuous transfer label. Example: “GATES® 75W 2 1/2 60 PSI WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet for sizes through 4" and 200 feet for sizes above 4". If a special transfer label is required, contact Gates Corporation for minimum quantity. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Meets SAE 20R1, Class D-2, tube and cover, standard wall. Cover: RMA (Class C) Limited oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 51

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

76W (Heavy Wall Coolant)

Marine Hose

(Specification 4176HD) Nom. I.D. (In.) 7/8 1 1 1/8 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 2 2 1/4 2 3/8 2 1/2 2 5/8 2 3/4 2 7/8 3 3 1/2 4

(mm) 22.2 25.4 28.6 31.8 34.9 38.1 41.3 44.5 47.6 50.8 57.2 60.3 63.5 66.7 69.9 73.0 76.2 88.9 101.6

Nom. O.D. (In.) 1.38 1.50 1.63 1.74 1.88 2.00 2.13 2.25 2.38 2.50 2.74 2.88 3.00 3.13 3.25 3.38 3.50 4.00 4.50

(mm) 35.1 38.1 41.4 44.5 47.8 50.8 54.1 57.2 60.5 63.5 69.9 73.2 76.2 79.5 82.6 85.9 88.9 101.6 114.3

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 175 175 175 125 110 112 106 100 94 88 88 81 75 69 63 63 63 50 38

(MPa) 1.21 1.21 1.21 .86 .76 .77 .73 .69 .65 .61 .61 .56 .52 .48 .43 .43 .43 .34 .26

Suction (In. Hg) 15.0 10.0 10.0 10.0 10.0 10.0 7.0 5.0 4.0 3.0 1.0 — — — — — — — —

(mm Hg) 381 254 254 254 254 254 178 127 102 76 25 — — — — — — — —

Min. Bend Radius (In.) 7.0 8.0 8.0 12.0 12.0 12.0 14.0 15.0 — — — — — — — — — — —

Tube: Reinforcement: Cover:

50' length coiled and wrapped in polyethylene. 50' carton: 7/8" size only.

STANDARDS:

Gates Item No. 4176-0856 4176-0857 4176-0859 4176-0861 4176-0863 4176-0865 4176-0867 4176-0869 4176-0871 4176-0872 4176-0874 4176-0875 4176-0876 4176-0877 4176-0878 4176-0879 4176-0880 4176-0883 4176-0886

Type P (EPDM). Black. Multiple plies of synthetic fabric. Type P (EPDM). Black. Heat and ozone resistant.

1, 5, 6 or 7. Reference the Hose Coupling Section.

REMNANT LENGTHS:

Stock (X) or Minimum Order Qty. X X X X X X X X 400 ft. X X 400 ft. X 400 ft. X 400 ft. X X X

-40°F to +257°F (-40°C to +125°C) continuous service.

COUPLINGS:

SPECIAL ORDER REQUIREMENTS:

(Kg) .26 .27 .29 .32 .35 .37 .40 .42 .45 .47 .52 .55 .58 .60 .62 .65 .68 .78 .89

Standard Pack 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft.

Water discharge at higher pressures than are possible with 75W and for heavy duty use on coolant connections on marine and stationary engines.

PACKAGING: BRANDING:

(mm) 178 203 203 305 305 305 356 381 — — — — — — — — — — —

Wt. Per Ft. (Lbs.) .58 .59 .64 .70 .76 .81 .87 .93 .98 1.04 1.15 1.21 1.27 1.32 1.37 1.43 1.49 1.71 1.95

Continuous transfer label. Example: “GATES® 76W 2 1/2 75 PSI WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Meets SAE 20R1, Class D-2, tube and cover, heavy wall. Cover: RMA (Class C) Limited oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 52

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Engine Coolant (Oil Resistant Softwall)

Marine Hose

(Specification 4169A) Nom. I.D. (In.) 3/4 7/8 1 1 1/8 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 2 2 1/8 2 1/4 2 3/8 2 1/2 2 5/8 2 3/4 2 7/8 3 3 1/4 3 1/2 4 4 1/2

(mm) 19.1 22.2 25.4 28.6 31.8 34.9 38.1 41.3 44.5 47.6 50.8 54.0 57.2 60.3 63.5 66.7 69.9 73.0 76.2 82.6 88.9 101.6 114.3

Nom. O.D. (In.) 1.17 1.30 1.42 1.55 1.67 1.80 1.92 2.05 2.17 2.30 2.42 2.55 2.67 2.80 2.92 3.05 3.17 3.30 3.42 3.67 3.92 4.42 4.92

(mm) 29.7 33.0 36.1 39.4 42.4 45.7 48.8 52.1 55.1 58.4 61.5 64.8 67.8 71.1 74.2 77.5 80.5 83.8 86.9 93.2 99.6 112.3 125.0

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 135 135 135 100 100 85 75 75 60 60 60 60 60 60 60 55 50 35 10 10 10

(MPa) 1.03 1.03 .93 .93 .93 .69 .69 .59 .52 .52 .41 .41 .41 .41 .41 .41 .41 .38 .34 .24 .07 .07 .07

Suction (In. Hg) — — — — — — — — — — — — — — — — — — — — — — —

(mm Hg) — — — — — — — — — — — — — — — — — — — — — — —

Min. Bend Radius (In.) 6.0 7.0 8.0 8.0 10.0 12.0 12.0 15.0 15.0 — — — — — — — — — — — — — —

Tube: Reinforcement: Cover:

Stock (X) or Minimum Order Qty. X X X X X X X X X X X X X X X 200 ft. X 200 ft. X 200 ft. X X 200 ft.

Gates Item No. 4169-0210 4169-0220 4169-0224 4169-0240 4169-0246 4169-0260 4169-0270 4169-0280 4169-0288 4169-0300 4169-0484 4169-0320 4169-0491 4169-0340 4169-0345 4169-0360 4169-0362 4169-0376 4169-0383 4169-0402 4169-0420 4169-0425 4169-0433

Type C (Nitrile). Black. Oil and heat resistant. Two plies of synthetic fabric. Type A (Neoprene). Black.

PACKAGING:

3' per carton.

STANDARDS:

Standard Pack 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft. 3 ft.

-40°F to +212°F (-40°C to +100°C) continuous service.

1, 5, 6 or 7. Reference the Hose Coupling Section.

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

(Kg) .15 .17 .20 .22 .23 .25 .27 .29 .31 .33 .35 .37 .39 .40 .43 .45 .47 .49 .50 .54 .58 .66 .73

Open end water discharge applications and coolant connections on marine and stationary engines where oil resistance is required.

COUPLINGS:

BRANDING:

(mm) 152 178 203 203 254 305 305 381 381 — — — — — — — — — — — — — —

Wt. Per Ft. (Lbs.) .34 .38 .43 .48 .51 .56 .60 .63 .68 .73 .77 .82 .85 .89 .94 .98 1.03 1.07 1.10 1.19 1.28 1.46 1.62

Continuous transfer label. Example: “GATES® 4169A 3/4 150 PSI WP MADE IN USA” Special production runs require minimum order quantities of 200 feet. None. Meets requirements of SAE 20R1, Class B Tube, Class C Cover. Tube: RMA (Class B) Medium oil resistance. Cover: RMA (Class C) Limited oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 53

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Engine Coolant (Wire Inserted - Hardwall)

Marine Hose

(Specification 4685WG) Nom. I.D. (In.) 1 1 1/8 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 2 2 1/8 2 1/4 2 3/8 2 1/2 2 5/8 2 3/4 2 7/8 3 3 1/2 4 5 6

(mm) 25.4 28.6 31.8 34.9 38.1 41.3 44.5 47.6 50.8 54.0 57.2 60.3 63.5 66.7 69.9 73.0 76.2 88.9 101.6 127.0 152.4

Nom. O.D. (In.) 1.46 1.58 1.71 1.83 1.96 2.08 2.21 2.33 2.46 2.58 2.71 2.83 2.96 3.08 3.21 3.33 3.43 3.93 4.43 5.43 6.43

(mm) 37.1 40.1 43.4 46.5 49.8 52.8 56.1 59.2 62.5 65.5 68.8 71.9 75.2 78.2 81.5 84.6 87.1 99.8 112.5 137.9 163.3

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 100 100 100 85 85 75 75 60 60 55 55 50 50 40 40 40 40 35 30 15 15

(MPa) .69 .69 .69 .59 .59 .52 .52 .41 .41 .38 .38 .34 .34 .28 .28 .28 .28 .24 .21 .10 .10

Suction (In. Hg) 25.0 25.0 25.0 25.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 15.0 15.0 15.0 15.0 15.0 10.0 5.0 5.0

(mm Hg) 635 635 635 635 508 508 508 508 508 508 508 508 508 381 381 381 381 381 254 127 127

Min. Bend Radius (In.) 2.0 2.5 2.5 3.0 3.5 3.5 4.0 4.5 5.0 5.5 6.0 6.5 6.5 7.0 7.5 9.0 9.0 12.0 20.0 24.0 —

Tube: Reinforcement: Cover:

Stock (X) or Minimum Order Qty. X X X X X X X X X X X X X X X X X X X X X

Gates Item No. 4685-2016 4685-2018 4685-2020 4685-2022 4685-2024 4685-2026 4685-2028 4685-2030 4685-2032 4685-2034 4685-2036 4685-2038 4685-2040 4685-2042 4685-2044 4685-2046 4685-2048 4685-2056 4685-2064 4685-2080 4685-2096

Type P (EPDM). Black. Multiple plies of synthetic fabric and two built-in helical steel wires. Type P (EPDM). Black with green spiral stripe.

1, 5, 6 or 7. Reference the Hose Coupling Section. 5' per carton.

STANDARDS:

Standard Pack 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft. 5 ft.

-40°F to +257°F (-40°C to +125°C) continuous service.

COUPLINGS:

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

(Kg) 1.13 1.25 1.36 1.47 1.59 1.70 1.81 1.93 2.16 2.29 2.40 2.52 2.63 2.74 2.86 2.99 3.11 3.58 4.06 6.10 7.26

Open end water discharge applications and coolant on marine and stationary engines where tight bends or suction capability are required.

PACKAGING: BRANDING:

(mm) 51 64 64 76 89 89 102 114 127 140 152 165 165 178 191 229 229 305 508 610 —

Wt. Per Ea. (Lbs.) 2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.75 5.05 5.30 5.55 5.80 6.05 6.30 6.60 6.85 7.90 8.95 13.45 16.00

Continuous transfer label. Example: “GATES® 24916 GREEN STRIPE® WIGS COOLANT & AIR 1" I.D. (25.4mm) MADE IN USA” Special production runs require minimum order quantities of 200 feet. None. Meets requirements of SAE 20R2 (20R5 Burst). Tube: Meets D-1, D-2 and D-3 (except D-2 oil swell). Cover: Meets D-1, D-2 and D-3.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 54

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Engine Coolant (Silicone)

Marine Hose

(Specification 4171) Nom. I.D. (In.) 3/8 1/2 5/8 3/4 7/8 1 1 1/8 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4 2 2 1/8 2 1/4 2 3/8 2 1/2 2 3/4 3 3 1/4 3 1/2 3 3/4 4 4 1/2

(mm) 9.5 12.7 15.9 19.1 22.2 25.4 28.6 31.8 34.9 38.1 41.3 44.5 50.8 54.0 57.2 60.3 63.5 69.9 76.2 82.6 88.9 95.3 101.6 114.3

Nom. O.D. (In.) .74 .87 .99 1.12 1.24 1.37 1.50 1.63 1.75 1.88 2.00 2.13 2.38 2.51 2.63 2.75 2.88 3.13 3.38 3.63 3.88 4.13 4.38 4.88

(mm) 18.8 22.1 25.2 28.5 31.5 34.8 38.1 41.4 44.5 47.8 50.8 54.1 60.5 63.8 66.8 69.9 73.2 79.5 85.9 92.2 98.6 104.9 111.3 124.0

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 110 110 110 110 110 90 90 85 85 85 80 80 75 75 75 65 65 50 50 40 35 35 35 25

(MPa) .76 .76 .76 .76 .76 .62 .62 .59 .59 .59 .55 .55 .52 .52 .52 .45 .45 .34 .34 .28 .24 .24 .24 .17

Suction (In. Hg) — — — — — — — — — — — — — — — — — — — — — — — —

(mm Hg) — — — — — — — — — — — — — — — — — — — — — — — —

Min. Bend Radius (In.) — — — — — — — — — — — — — — — — — — — — — — — —

Gates Item No. 4171-0195 4171-0197 4171-0204 4171-0206 4171-0210 4171-0213 4171-0217 4171-0265 4171-0260 4171-0270 4171-0275 4171-0280 4171-0285 4171-0224 4171-0223 4171-0229 4171-0234 4171-0238 4171-0246 4171-0249 4171-0241 4171-0835 4171-0290 4171-0295

Type MQ (Silicone). Orange. Multiple plies of synthetic fabric. Type MQ (Silicone). Green.

1, 5, 6 or 7. Reference the Hose Coupling Section. 10' per carton.

STANDARDS:

Stock (X) or Minimum Order Qty. X X X X X X X X X X X X X X X X X X X X X 200 ft. X X

-65°F to +347°F (-54°C to +175°C) continuous service. Tube: Reinforcement: Cover:

COUPLINGS:

BRANDING:

(Kg) .09 .10 .12 .14 .16 .18 .20 .22 .24 .26 .28 .29 .33 .35 .37 .39 .40 .44 .48 .52 .56 .60 .64 .71

Standard Pack 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft.

Open end water discharge and coolant connections on marine and stationary engines where extremely high and low temperature resistance is required.

PACKAGING:

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

(mm) — — — — — — — — — — — — — — — — — — — — — — — —

Wt. Per Ft. (Lbs.) .19 .23 .27 .31 .35 .40 .44 .48 .52 .57 .61 .65 .73 .77 .81 .85 .89 .97 1.05 1.14 1.23 1.32 1.40 1.56

Unlabeled. Special production runs require minimum order quantities of 200 feet. None. Meets requirements of SAE 20R1, Class A standard wall.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 55

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Heater Hose

Marine Hose

(Specification 4230T) Nom. I.D. (In.) 5/16 3/8 1/2 5/8 3/4 1

(mm) 7.9 9.5 12.7 15.9 19.1 25.4

Nom. O.D. (In.) .62 .69 .81 .94 1.06 1.34

(mm) 15.8 17.5 20.6 23.9 26.9 34.0

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 75 75 75 75 75 75

(MPa) .52 .52 .52 .52 .52 .52

Suction (In. Hg) 25.0 25.0 25.0 25.0 25.0 25.0

(mm Hg) 635 635 635 635 635 635

Min. Bend Radius (In.) 2.0 2.5 3.0 4.0 5.0 7.0

(mm) 51 64 76 102 127 178

Wt. Per Ft. (Lbs.) .14 .16 .19 .23 .26 .37

(Kg) .06 .07 .09 .10 .12 .17

Standard Pack Reel Carton Reel Reel Carton Carton

-40°F to +257°F (-40°C to +125°C) continuous service. Tube: Reinforcement: Cover:

Type P (EPDM). Black. Synthetic, high tensile textile cord. Type P (EPDM). Black.

1, 5, 6 or 7. Reference the Hose Coupling Section.

PACKAGING:

5/16": Packaged in 600' to 800' reels. Maximum 4 pieces. Minimum length 25'. 3/8": Packaged 500' per carton. Maximum 2 pieces. Minimum length 25'. 1/2": Packaged in 600' to 800' reels. Maximum 4 pieces. Minimum length 25'. 5/8": Packaged 300' per reel. Maximum 2 pieces. Minimum length 25'. 3/4": Packaged 200' per carton. Maximum 2 pieces. Minimum length 25'. 1": Packaged 600' per carton. Maximum 2 pieces. Minimum length 25'.

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Gates Item No. 4230-0193 4230-0129 4230-0060 4230-0135 4230-0134 4230-0150

Standard heater lines and small diameter coolant connections.

COUPLINGS:

BRANDING:

Stock (X) or Minimum Order Qty. X X X X X X

Continuous ink brand. Example: “GATES® EB 4230T 1 INCH (25.4mm) MADE IN U.S.A.” Special production runs require minimum order quantities of 25,000 feet. None. Meets requirements of SAE 20R3 Class D-2 (except durometer and compression set).

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 56

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Wet Exhaust (Softwall)

Marine Hose

(Specification 3137ME) Nom. I.D. (In.) 1 1/8 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 2 2 1/8 2 1/4 2 3/8 2 1/2 2 5/8 2 3/4 2 7/8 3 3 1/2 4 4 1/2 5 6

(mm) 28.6 31.8 34.9 38.1 41.3 44.5 47.6 50.8 54.0 57.2 60.3 63.5 66.7 69.9 73.0 76.2 88.9 101.6 114.3 127.0 152.4

Nom. O.D. (In.) 1.40 1.53 1.69 1.78 1.91 2.03 2.19 2.32 2.45 2.57 2.69 2.82 2.95 3.09 3.23 3.36 3.86 4.36 4.86 5.37 6.38

(mm) 35.6 38.9 42.9 45.2 48.5 51.6 55.6 58.9 62.2 65.3 68.3 71.6 74.9 78.5 82.0 85.3 98.0 110.7 123.4 136.4 162.1

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

PACKAGING: BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Max. W.P. (psi) 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100

(MPa) .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69

Suction (In. Hg) — — — — — — — — — — — — — — — — — — — — —

(mm Hg) — — — — — — — — — — — — — — — — — — — — —

Min. Bend Radius (In.) — — — — — — — — — — — — — — — — — — — — —

(mm) — — — — — — — — — — — — — — — — — — — — —

Wt. Per Ea. (Lbs.) 5.59 6.07 6.58 7.12 7.63 8.15 8.63 9.18 9.69 10.19 10.70 11.24 11.79 12.29 12.80 14.45 16.63 18.57 21.14 23.35 27.14

(Kg) 2.54 2.75 2.98 3.23 3.46 3.70 3.91 4.16 4.40 4.58 4.85 5.10 5.35 5.58 5.81 6.55 7.54 8.42 9.59 10.59 12.58

Standard Pack 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft.

Stock (X) or Minimum Order Qty. X X X X X X X X X X X X X X X X X X X X X

Gates Item No. 3137-1207 3137-1209 3137-1213 3137-1215 3137-1217 3137-1219 3137-1221 3137-1223 3137-1225 3137-1227 3137-1229 3137-1231 3137-1233 3137-1235 3137-1237 3137-1239 3137-1245 3137-1249 3137-1252 3137-1253 3137-1254

Heavy-duty fabric reinforced. Designed for use where wire support is not required. Meets marine water and wet exhaust hose requirements. May be used for engine water circulation, discharge lines, heat exchangers and straight wet exhaust connections. For water applications hose is rate at 100 PSI. -40°F to +257°F (-40°C to +125°C) continuous service. Tube: Reinforcement: Cover:

Type P (EPDM). Black. Two plies of synthetic fabric. Type P (EPDM). Black with blue spiral stripe.

All lengths packaged in poly wrap. Continuous transfer label. Example: “GATES® MARINE WET EXHAUST SOFTWALL 100 PSI WP MADE IN U.S.A.” Special production runs require minimum order quantities of 200 feet. None. Meets requirements of SAE J2006 R1.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 57

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Wet Exhaust (Hardwall)

Marine Hose

(Specification 4686ME) Nom. I.D. (In.) 1 1/8 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 2 2 1/8 2 1/4 2 3/8 2 1/2 2 5/8 2 3/4 2 7/8 3 3 1/2 4 4 1/2 5 5 1/2 6

(mm) 28.6 31.8 34.9 38.1 41.3 44.5 47.6 50.8 54.0 57.2 60.3 63.5 66.7 69.9 73.0 76.2 88.9 101.6 114.3 127.0 139.7 152.4

Nom. O.D. (In.) 1.50 1.63 1.75 1.88 2.00 2.12 2.24 2.36 2.49 2.63 2.75 2.90 3.02 3.22 3.42 3.54 4.04 4.54 5.04 5.54 6.04 6.68

(mm) 38.1 41.4 44.5 47.8 50.8 53.9 56.9 59.9 63.3 66.8 69.9 73.7 76.7 81.8 86.9 89.9 102.6 115.3 128.0 140.7 153.4 169.7

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

PACKAGING: BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Max. W.P. (psi) 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100

(MPa) .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69 .69

Suction (In. Hg) 25.0 25.0 25.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 15.0 15.0 15.0 15.0 15.0 10.0 10.0 5.0 5.0 5.0

(mm Hg) 635 635 635 508 508 508 508 508 508 508 508 508 381 381 381 381 381 254 254 127 127 127

Min. Bend Radius (In.) 2.5 2.5 3.0 3.5 3.5 4.0 4.5 5.0 5.5 6.0 6.5 6.5 7.0 7.5 8.0 9.0 12.0 20.0 22.0 24.0 — —

(mm) 64 64 76 89 89 102 114 127 140 152 165 165 178 191 203 229 305 508 559 610 — —

Wt. Per Ea. (Lbs.) 7.40 8.03 8.66 9.31 9.81 10.57 11.23 11.90 12.56 13.20 14.62 15.33 16.00 16.69 17.35 19.41 22.31 27.60 30.89 34.04 39.29 40.37

(Kg) 3.36 3.64 3.93 4.22 4.45 4.79 5.09 5.40 5.70 5.99 6.63 6.95 7.26 7.57 7.87 8.80 10.12 12.52 14.01 15.44 17.82 18.31

Stock (X) or Minimum Order Qty. X X X X X X X X X X X X X X X X X X X X X X

Gates Item No. 4686-0602 4686-0604 4686-0606 4686-0608 4686-0610 4686-0612 4686-0614 4686-0616 4686-0618 4686-0620 4686-0622 4686-0624 4686-0626 4686-0628 4686-0630 4686-0632 4686-0638 4686-0640 4686-0642 4686-0643 4686-0645 4686-0646

Heavy-duty fabric-reinforced hose with a helical steel wire reinforcement to meet marine water and wet exhaust hose requirements. May be used for engine water circulation, discharge lines, heat exchangers and wet exhaust connections. For water applications hose is rate at 100 PSI. -40°F to +257°F (-40°C to +125°C) continuous service. Tube: Reinforcement: Cover:

Type P (EPDM). Black. Two plys of synthetic fabric and two built-in helical steel wires. Type P (EPDM). Black with blue spiral stripe.

All lengths packaged in poly wrap. Continuous transfer label. Example: “GATES® MARINE WET EXHAUST HARDWALL 100 PSI WP SAE J2006R2 MADE IN U.S.A.” Special production runs require minimum order quantities of 200 feet. None. Meets requirements of SAE J2006 R2.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 58

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

4684CF (Wet Exhaust Corrugated)

Marine Hose

(Specification 4684CF) Nom. I.D. (In.) 1 1 1/8 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 2 2 1/8 2 1/4 2 3/8 2 1/2 2 5/8 2 3/4 2 7/8 3 3 1/2 4 4 1/2 5 6

(mm) 25.4 28.6 31.8 34.9 38.1 41.3 44.5 47.6 50.8 54.0 57.2 60.3 63.5 66.7 69.9 73.0 76.2 88.9 101.6 114.3 127.0 152.4

Nom. O.D. (In.) 1.44 1.56 1.69 1.81 1.94 2.06 2.19 2.31 2.44 2.56 2.69 2.81 2.94 3.06 3.19 3.31 3.44 4.06 4.44 4.94 5.44 6.46

(mm) 36.6 39.6 42.9 46.0 49.3 52.3 55.6 58.7 62.0 65.0 68.3 71.4 74.7 77.7 81.0 84.1 87.4 103.1 112.8 125.5 138.2 164.1

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

PACKAGING:

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Max. W.P. (psi) 100 100 100 85 85 75 75 60 60 55 55 50 50 40 40 40 40 35 30 25 15 15

(MPa) .69 .69 .69 .59 .59 .52 .52 .41 .41 .38 .38 .34 .34 .28 .28 .28 .28 .24 .21 .17 .10 .10

Suction (In. Hg) 25.0 25.0 25.0 25.0 25.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 15.0 15.0 15.0 15.0 15.0 10.0 5.0 5.0 5.0

(mm Hg) 635 635 635 635 635 508 508 508 508 508 508 508 508 381 381 381 381 381 254 127 127 127

Min. Bend Radius (In.) 3.0 4.0 4.0 4.0 4.0 5.0 5.0 5.0 5.0 6.0 6.0 7.0 7.0 9.0 10.0 11.0 12.0 17.0 24.0 27.0 30.0 36.0

(mm) 76 102 102 102 102 127 127 127 127 152 152 178 178 229 254 279 305 432 610 914 1016 —

Wt. Per Ft. (Lbs.) .51 .56 .61 .66 .70 .75 .80 .83 .88 .93 .98 1.03 1.08 1.12 1.17 1.21 1.26 1.45 1.64 1.84 2.03 2.42

(Kg) .23 .25 .28 .30 .32 .34 .36 .38 .40 .42 .45 .47 .49 .51 .53 .55 .57 .66 .74 .84 .92 1.10

Standard Pack 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft.

Stock (X) or Minimum Order Qty. X X X X X X X X X X X X X X X X X X X 200 ft. 200 ft. 200 ft.

Gates Item No. 4684-1540 4684-1545 4684-1551 4684-1556 4684-1561 4684-1601 4684-1611 4684-1651 4684-1660 4684-1670 4684-1680 4684-1690 4684-1700 4684-1711 4684-1720 4684-1730 4684-1740 4684-1750 4684-1760 4684-1764 4684-1766 4684-1722

Marine wet exhaust and general purpose applications. Suitable for coolant lines where tight bends are required. -40°F to +212°F (-40°C to +100°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Oil and heat resistant. Synthetic fabric with built-in wire. Type A (Neoprene). Black with red spiral stripe. Oil and heat resistant.

1", 1 1/4", 1 3/8", 1 1/2", 1 5/8", 1 7/8": Packaged 5 each 10' coils in a carton. 3 1/2" through 6": Packaged in straight lengths in woven fiber. All other sizes: Packaged 10' per carton. Continuous transfer label every 10 ft. Example: “GATES® 4684CF Engine Coolant-Marine Wet Exhaust 2 Inch Made In U.S.A.” For enlarged or straight ends, contact Gates Corporation for pricing. Special production runs require minimum order quantities of 200 feet per size. Lengths can be as short as one foot, but minimum billing is for ten feet. None. Meets requirements of SAE 20R2, SAE 20R5, SAE J2006. Tube: RMA (Class B) Medium oil resistance. Cover: RMA (Class C) Limited oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 59

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

C5M Fuel Line

Marine Hose

(Specification 3658F) Nom. I.D. (In.) 1/4 5/16 13/32 1/2 5/8 7/8

(mm) 6.4 7.9 10.3 12.7 15.9 22.2

Nom. O.D. (In.) .58 .67 .77 .92 1.08 1.23

(mm) 14.7 17.0 19.6 23.4 27.4 31.2

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 500 500 500 500 500 500

(MPa) 3.45 3.45 3.45 3.45 3.45 3.45

Suction (In. Hg) 20.0 20.0 20.0 20.0 20.0 20.0

(mm Hg) 508 508 508 508 508 508

Min. Bend Radius (In.) 1.3 1.3 1.8 2.3 2.8 3.5

(mm) 33 33 46 58 71 89

Wt. Per Ft. (Lbs.) .22 .26 .29 .40 .51 .51

(Kg) .10 .12 .13 .18 .23 .23

Standard Pack Reel Reel Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X X X X

Gates Item No. 3658-1965 3658-1969 3658-1973 3658-1977 3658-1981 3658-1985

All commercial and recreational vessel fuel line applications. Suitable for marine diesel, gasoline, gasohol fuels and hot oil applications. -4°F to +212°F (-20°C to +100°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Oil and heat resistant. Braided, high tensile steel wire. Type C2 (Modified Nitrile). Blue.

COUPLINGS:

72 Gates Power Crimp®. For Stainless Steel PC and Brass Reusable couplings reference Gates Hydraulic catalog #35093.

PACKAGING:

1/4" and 5/16": Packaged in 385' reels. Maximum 4 pieces. Minimum length 10'. 13/32": Packaged in 330' reels. Maximum 3 pieces. Minimum length 10'. 1/2": Packaged in 275' reels. Maximum 3 pieces. Minimum length 10'. 5/8": Packaged in 220' reels. Maximum 3 pieces. Minimum length 10'. 7/8": Packaged in 165' reels. Maximum 3 pieces. Minimum length 10'.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous transfer label. Example: “GATES® 8 C5M SAEJ1527 USCG TYPE A1 ISO 7840-A1 HOSE 500 PSI (3.45MPa) FLAME RESISTANT USMSHA 2G-IC-11C/18” Special production runs require minimum order quantities of 5,000 feet. None. Hose is NMMA type accepted. Meets requirements of SAE J1942 and SAE J1527, USCG Type A, Class 1, Style R3, SAE J30R2, MSHA and ABS. Tube: RMA (Class A) High oil resistance. Cover: RMA (Class C) Limited oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 60

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Fuel Line (USCG Type A1)

Marine Hose

(Specification 4219M) 25 Foot Lengths Nom. I.D. (In.) 1/4 5/16 3/8 1/2 5/8

(mm) 6.4 7.9 9.5 12.7 15.9

Nom. O.D. (In.) .64 .70 .77 .89 1.01

(mm) 16.3 17.8 19.6 22.6 25.7

Max. W.P. (psi) 40 40 40 40 40

(mm) 16.3 17.8 19.6 22.6 25.7

Max. W.P. (psi) 40 40 40 40 40

(mm) 16.3 17.8 19.6 22.6 25.7

Max. W.P. (psi) 40 40 40 40 40

(MPa) .28 .28 .28 .28 .28

Suction (In. Hg) 28.0 28.0 28.0 28.0 28.0

(MPa) .28 .28 .28 .28 .28

Suction (In. Hg) 28.0 28.0 28.0 28.0 28.0

(MPa) .28 .28 .28 .28 .28

Suction (In. Hg) 28.0 28.0 28.0 28.0 28.0

(mm Hg) 711 711 711 711 711

Min. Bend Radius (In.) 2.5 3.0 3.0 5.0 6.0

(mm Hg) 711 711 711 711 711

Min. Bend Radius (In.) 2.5 3.0 3.0 5.0 6.0

(mm Hg) 711 711 711 711 711

Min. Bend Radius (In.) 2.5 3.0 3.0 5.0 6.0

(mm) 64 76 76 127 152

Wt. Per Ea. (Lbs.) 4.73 5.08 6.10 7.37 8.61

(Kg) 1.94 2.20 2.50 3.03 3.53

Standard Pack 25 ft. 25 ft. 25 ft. 25 ft. 25 ft.

Stock (X) or Minimum Order Qty. X X X X X

Gates Item No. 4219-4145 4219-4565 4219-4385 4219-4125 4219-4585

(mm) 64 76 76 127 152

Wt. Per Ea. (Lbs.) 8.56 10.15 11.04 13.33 15.57

(Kg) 3.88 4.41 5.01 6.05 7.06

Standard Pack 50 ft. 50 ft. 50 ft. 50 ft. 50 ft.

Stock (X) or Minimum Order Qty. X X X X X

Gates Item No. 4219-4146 4219-4566 4219-4567 4219-4126 4219-4586

(Kg) 19.41 22.04 25.03 30.23 35.30

Standard Pack 250 ft. 250 ft. 250 ft. 250 ft. 250 ft.

Stock (X) or Minimum Order Qty. X X X X X

Gates Item No. 4219-4140 4219-4560 4219-4380 4219-4120 4219-4580

50 Foot Lengths Nom. I.D. (In.) 1/4 5/16 3/8 1/2 5/8

(mm) 6.4 7.9 9.5 12.7 15.9

Nom. O.D. (In.) .64 .70 .77 .89 1.01

Reel Lengths Nom. I.D. (In.) 1/4 5/16 3/8 1/2 5/8

(mm) 6.4 7.9 9.5 12.7 15.9

Nom. O.D. (In.) .64 .70 .77 .89 1.01

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

PACKAGING:

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

(mm) 64 76 76 127 152

Wt. Per Ea. (Lbs.) 45.36 53.57 60.99 66.65 86.10

Flexible connections between rigid fuel distribution lines and engine. Excellent for vent lines and emission control systems. Suitable for marine diesel and gasohol blends of ethanol, methanol and ethers up to 10%. -40°F to +212°F (-40°C to +100°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Oil and heat resistant. Braided, high tensile synthetic cord. Type A (Neoprene). Black.

1/4" through 5/8": Packaged 25' per carton. 1/4" through 5/8": Packaged 50' per carton. 1/4" through 5/8": Packaged in 250'. Maximum of 3 pieces. Minimum length 15'. Continuous ink brand. Example: “GATES® 4219M FUEL LINE USCG TYPE A1 SAE J1527 NMMA TYPE ACCEPTED MADE IN U.S.A.” Special production runs require minimum order quantities of 5,000 feet. Maximum length is 10 feet. None. Hose is NMMA type accepted. Meets requirements of SAE J1527, USCG Type A1, Class 1, Style R1. Tube: RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 61

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Fuel Line (USCG Type B)

Marine Hose

(Specification 4219N) 50 Foot Lengths Nom. I.D. (In.) 1/4 5/16

(mm) 6.4 7.9

Nom. O.D. (In.) .50 .58

(mm) 12.7 14.7

Max. W.P. (psi) 40 40

(mm) 12.7 14.7

Max. W.P. (psi) 40 40

(MPa) .28 .28

Suction (In. Hg) 28.0 28.0

(MPa) .28 .28

Suction (In. Hg) 28.0 28.0

(mm Hg) 711 711

Min. Bend Radius (In.) 2.5 3.0

(mm Hg) 711 711

Min. Bend Radius (In.) 2.5 3.0

(mm) 64 76

Wt. Per Ea. (Lbs.) 4.48 5.59

(Kg) 2.03 2.54

Standard Pack 50 ft. 50 ft.

Stock (X) or Minimum Order Qty. 25,000 ft. 25,000 ft.

Gates Item No. 4219-4046 4219-4066

(Kg) 10.16 12.68

Standard Pack 250 ft. 250 ft.

Stock (X) or Minimum Order Qty. X X

Gates Item No. 4219-4040 4219-4060

250 Foot Reels Nom. I.D. (In.) 1/4 5/16

(mm) 6.4 7.9

Nom. O.D. (In.) .50 .58

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

PACKAGING:

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

(mm) 64 76

Wt. Per Ea. (Lbs.) 22.40 27.95

Flexible connections between rigid fuel distribution lines and engine where the hose is in an open environment on pleasure craft. Excellent for vent lines. Suitable for marine diesel and gasohol blends of ethanol, methanol and ethers up to 10%. NOTE: Not recommended for concealed applications. Not approved for use on commercial or for-hire craft. -40°F to +250°F (-40°C to +121°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Synthetic, high tensile textile cord. Type M (Hypalon). Black.

1/4" and 5/16": 50' per carton. 1/4": Packaged in 250' reels. Maximum of 2 pieces. Minimum length 15'. 5/16": Packaged in 250' single piece reels. Continuous ink brand. Example: “GATES® 4219N 1/2 INCH MARINE FUEL LINE USCG TYPE B1 SAE J1527 NMMA TYPE ACCEPTED MADE IN U.S.A. Special production runs require minimum order quantities of 25,000 feet. None. Hose is NMMA type accepted. Meets requirements of SAE J1527, USCG Type B, Class 1, Style R1. Tube: RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 62

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

4219G (Fuel Line & Tank Vent)

Marine Hose

(Specification 4219G) Nom. I.D. (In.) 3/16 1/4 5/16 3/8 1/2 5/8

(mm) 4.8 6.4 7.9 9.5 12.7 15.9

Nom. O.D. (In.) .41 .50 .56 .62 .78 .94

(mm) 10.4 12.7 14.2 15.8 19.8 23.9

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

PACKAGING: BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Max. W.P. (psi) 50 50 50 50 35 35

(MPa) .34 .34 .34 .34 .24 .24

Suction (In. Hg) 24.0 24.0 24.0 24.0 10.0 10.0

(mm Hg) 610 610 610 610 254 254

Min. Bend Radius (In.) 3.0 3.0 3.0 4.0 5.0 6.0

(mm) 76 76 76 102 127 152

Wt. Per Ft. (Lbs.) .07 .09 .10 .12 .16 .23

(Kg) .03 .04 .05 .05 .07 .10

Standard Pack Reel Reel Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X X X X

Gates Item No. 4219-0093 4219-0103 4219-0107 4219-0109 4219-0102 4219-0097

Fuel line applications to provide flexible connections between rigid fuel distribution lines and the engine. Also for use in evaporative emission control systems and as a vent line. NOTE: Not recommended for fuel injection systems. -40°F to +257°F (-40°C to +125°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Oil, gasoline and gasohol resistant. Synthetic, high tensile textile. Type C2 (NBR/PVC). Black. Fuel, oil, ozone and high temperature resistant.

3/16" through 5/8": Packaged in 450' to 650' reels. Maximum 5 pieces. One piece 25' to 49'. All other pieces 49' and over. Continuous ink label. Example: “GATES® 4219G Fuel Line PCV/EEC 3/8 Inch (9.5mm) SAE 30R7 Made In U.S.A.” Special production runs require minimum order quantities of 25,000 feet. None. Exceeds requirements of SAE 30R6 & SAE 30R7. Hose is NMMA type accepted. Tube: RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 63

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Fuel Fill (USCG Type A1 and B1)

Marine Hose

(Specification 4689M) 12 1/2 Foot Lengths Nom. I.D. (In.) 1 1/2 1 5/8 1 7/8 2 2 3/8

(mm) 38.1 41.3 47.6 50.8 60.3

Nom. O.D. (In.) 1.90 2.03 2.28 2.40 2.78

(mm) 48.3 51.6 57.9 61.0 70.6

Max. W.P. (psi) 18 18 18 18 18

(mm) 35.6 48.3 51.6 57.9 61.0 70.6

Max. W.P. (psi) 35 18 18 18 18 18

(MPa) .12 .12 .12 .12 .12

Suction (In. Hg) 20.0 20.0 20.0 20.0 20.0

(MPa) .24 .12 .12 .12 .12 .12

Suction (In. Hg) 20.0 20.0 20.0 20.0 20.0 20.0

(mm Hg) 508 508 508 508 508

Min. Bend Radius (In.) 7.0 8.0 9.0 9.5 10.0

(mm Hg) 508 508 508 508 508 508

Min. Bend Radius (In.) 4.0 7.0 8.0 9.0 9.5 10.0

(mm) 178 203 229 241 254

Wt. Per Ea. (Lbs.) 9.44 10.06 11.34 12.03 14.02

(Kg) 4.28 4.56 5.14 5.46 6.36

Standard Pack 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft. 12 1/2 ft.

Stock (X) or Minimum Order Qty. 200 ft. 200 ft. 200 ft. 200 ft. 200 ft.

Gates Item No. 4689-5000 4689-5001 4689-5002 4689-5003 4689-5004

(Kg) 12.25 17.12 18.26 20.58 21.83 25.44

Standard Pack 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft.

Stock (X) or Minimum Order Qty. X X X X X X

Gates Item No. 4689-5005 4689-5012 4689-5007 4689-5008 4689-5009 4689-5010

50 Foot Lengths Nom. I.D. (In.) 1 1 1/2 1 5/8 1 7/8 2 2 3/8

(mm) 25.4 38.1 41.3 47.6 50.8 60.3

Nom. O.D. (In.) 1.40 1.90 2.03 2.28 2.40 2.78

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

PACKAGING: BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

(mm) 102 178 203 229 241 254

Wt. Per Ea. (Lbs.) 27.01 37.74 40.25 45.37 48.13 56.08

Designed to transfer fuel from the filler neck to the fuel tank. This top-quality hose is flame and fire resistant and its low permeation rate exceeds USCG standards. Suitable for marine diesel fuel, gasoline and gasohol blends of ethanol, methanol and ethers up to 15%. -40°F to +212°F (-40°C to +100°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Synthetic, high tensile textile cord with steel wire helix. Type A (Neoprene). Black with red spiral stripe.

12 1/2' and 50' lengths: Packaged one length per carton. Continuous transfer label. Example: “GATES® MARINE FUEL FILL MEETS USCG & J1527 TYPE A1 MADE IN U.S.A.″ Special production runs require minimum order quantities of 200 feet. None. Hose is NMMA type accepted. Meets requirements of SAE J1527, USCG Type A1 and B1. Tube: RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 64

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

4663K (Fuel Fill - Corrugated)

Marine Hose

(Specification 4663K) Nom. I.D. (In.) 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 2 2 1/4 2 1/2 3

(mm) 34.9 38.1 41.3 44.5 47.6 50.8 57.2 63.5 76.2

Nom. O.D. (In.) 1.63 1.77 1.90 2.02 2.14 2.25 2.50 2.75 3.27

(mm) 41.4 45.0 48.3 51.3 54.4 57.2 63.5 69.9 83.1

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

PACKAGING: BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Max. W.P. (psi) 20 20 20 20 20 20 20 20 20

(MPa) .14 .14 .14 .14 .14 .14 .14 .14 .14

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 5.0 5.0 5.5 6.0 6.0 7.0 8.0 12.0 —

(mm) 127 127 140 152 152 178 203 305 —

Wt. Per Ft. (Lbs.) .38 .41 .44 .47 .50 .53 .54 .65 .84

(Kg) .17 .19 .20 .21 .23 .24 .25 .30 .38

Standard Pack 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft.

Stock (X) or Minimum Order Qty. X X 200 ft. 200 ft. 200 ft. X X 200 ft. 200 ft.

Gates Item No. 4663-2828 4663-2830 4663-3624 4663-3976 4663-2933 4663-2930 4663-2932 4663-2929 4663-3625

Fuel tank filler applications to provide a flexible connector between fuel tank and fill pipe. Suitable for fill applications on automobiles, trucks, buses and other similar applications where exceptionally flexible hose is required. -40°F to +212°F (-40°C to +100°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Oil and heat resistant. Single ply of synthetic fabric and two built-in helical steel wires. Type A (Neoprene). Black with white spiral stripe. Fabric reinforcement coated with Neoprene.

10' per carton. Continuous transfer label. Example: “GATES® 4663K Fuel Fill Hose Made In U.S.A.” Special production runs require minimum order quantities of 200 feet. Maximum length is 10 feet. None. Hose is NMMA type accepted. Meets requirements of SAE 30R5. Tube: RMA (Class B) Medium oil resistance. Cover: RMA (Class C) Limited oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 65

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Vacuum Tubing

Marine Hose

(Specification 4040A) Nom. I.D. (In.) 7/64 5/32 7/32 1/4 5/16 3/8

(mm) 2.8 4.0 5.6 6.4 7.9 9.5

Nom. O.D. (In.) 1/8 3/16 1/4 5/16 3/8 7/16

(mm) 3.2 4.8 6.4 7.9 9.5 11.1

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION: PACKAGING:

Max. W.P. (psi) — — — — — —

(mm Hg) 762 762 762 762 762 762

Min. Bend Radius (In.) 1.5 1.5 2.0 2.0 2.5 3.0

(mm) 38 38 51 51 64 76

Wt. Per Ea. (Lbs.) 1.00 1.50 2.50 3.00 1.75 2.50

(Kg) .45 .68 1.13 1.36 .79 1.13

Standard Pack 50 ft. 50 ft. 50 ft. 50 ft. 25 ft. 25 ft.

Stock (X) or Minimum Order Qty. X X X X X X

Gates Item No. 4040-4101 4040-4104 4040-4107 4040-4110 4040-4112 4040-4113

Ideal for windshield washers and vacuum-operated accessories. -40°F to +257°F (-40°C to +125°C) continuous service. Tube:

Type P (EPDM). Black. Heat resistant.

7/64" through 3/8": Packaged 50' per reel. 5/16" and 3/8": Packaged 25' per reel.

BRANDING:

None.

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

None.

STANDARDS:

(MPa) — — — — — —

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0

None. Tested to SAE J1037.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 66

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

609W (Dry Cement Delivery)

Material Handling Hose

(Specification 3129F, 3129H, 3129L) 1/8″ Tube Thickness (3129L) Nom. I.D. (In.) 3 4 4 1/2 5 6 6 5/8

(mm) 76.2 101.6 114.3 127.0 152.4 168.3

Nom. O.D. (In.) 3.47 4.47 4.97 5.47 6.47 7.10

(mm) 88.1 113.5 126.2 138.9 164.3 180.3

Max. W.P. (psi) 40 40 35 30 25 20

(MPa) .28 .28 .24 .21 .17 .14

Suction (In. Hg) — — — — — —

(MPa) .41

Suction (In. Hg) —

(MPa) .41

Suction (In. Hg) —

(mm Hg) — — — — — —

Min. Bend Radius (In.) 36.0 48.0 54.0 60.0 72.0 72.0

(mm Hg) —

Min. Bend Radius (In.) 48.0

(mm Hg) —

Min. Bend Radius (In.) 48.0

(mm) 914 1219 1372 1524 1829 1829

Wt. Per Ft. (Lbs.) 1.30 1.69 1.89 2.09 2.48 2.73

(mm) 1219

Wt. Per Ft. (Lbs.) 2.21

(mm) 1219

Wt. Per Ft. (Lbs.) 2.69

(Kg) .59 .77 .86 .95 1.13 1.24

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. X X X X X 200 ft.

Gates Item No. 3129-0660 3129-0670 3129-0675 3129-0680 3129-0690 3129-0700

(Kg) 1.00

Standard Pack 100 ft.

Stock (X) or Minimum Order Qty. X

Gates Item No. 3129-0790

(Kg) 1.22

Standard Pack 100 ft.

Stock (X) or Minimum Order Qty. X

Gates Item No. 3129-0570

3/16″ Tube Thickness (3129H) Nom. I.D. (In.) 4

(mm) 101.6

Nom. O.D. (In.) 4.61

(mm) 117.1

Max. W.P. (psi) 60

1/4″ Tube Thickness (3129F) Nom. I.D. (In.) 4

(mm) 101.6

Nom. O.D. (In.) 4.73

(mm) 120.1

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 60

Pneumatic transfer of bulk cement and other dry bulk materials. -40°F to +150°F (-40°C to +66°C) continuous service. Tube: Reinforcement: Cover:

Type D3 (Natural Rubber). Black. Static conductive. Synthetic, high tensile textile. Type D (SBR). Black with gray spiral stripe.

COUPLINGS:

5, 7, 49 or 78. Reference the Hose Coupling Section.

PACKAGING:

100' length coiled and wrapped in polyethylene.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Continuous transfer label. Example: “GATES® 609W Dry Cement Delivery - Static Conductive Tube 40 PSI (.28MPa) WP Made In U.S.A.” Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 67

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

688SB (Bulk Commodity)

Material Handling Hose

(Specification 4691L) Nom. I.D. (In.) 2 2 3 4 4 4 1/2 5 6 6

(mm) 50.8 50.8 76.2 101.6 101.6 114.3 127.0 152.4 152.4

Nom. O.D. (In.) 2.77 2.77 3.81 4.77 4.77 5.27 5.77 6.76 6.76

(mm) 70.4 70.4 96.8 121.2 121.2 133.9 146.6 171.7 171.7

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 60 60 60 45 45 40 40 40 40

(MPa) .41 .41 .41 .31 .31 .28 .28 .28 .28

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 16.0 16.0 24.0 32.0 32.0 36.0 40.0 48.0 48.0

(mm) 406 406 610 813 813 914 1016 1219 1219

Wt. Per Ft. (Lbs.) 1.65 1.65 2.54 3.21 3.21 3.57 3.93 4.65 4.65

(Kg) .75 .75 1.15 1.46 1.46 1.62 1.78 2.11 2.11

Standard Pack 100 ft. 200 ft. 100 ft. 100 ft. 200 ft. 50 ft. 50 ft. 50 ft. 200 ft.

Stock (X) or Minimum Order Qty. X 400 ft. X X 400 ft. X X X 400 ft.

Gates Item No. 4691-0305 4691-0306 4691-0325 4691-0340 4691-4342 4691-0355 4691-0360 4691-0346 4691-0349

Transfer of bulk materials via suction, gravity or pneumatic systems where abrasion resistance is the primary requirement. Examples: Dry cement, sand, gravel, feed, seed and slurries. -40°F to +150°F (-40°C to +66°C) continuous service. Tube: Reinforcement: Cover:

Type D3 (Natural Rubber). Black. Static conductive. 3/16" thick. Synthetic, high tensile textile with steel wire helix. Type D (SBR). Black corrugated with gray spiral stripe.

COUPLINGS:

5, 6, 7, 49 or 78. Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled and wrapped in polyethylene.

BRANDING:

Continuous transfer label. Example: “GATES® 688SB Wet-Dry Bulk Commodity 60 PSI (.41MPa) WP Made In U.S.A.”

SPECIAL ORDER REQUIREMENTS:

REMNANT LENGTHS:

Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 68

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Hot Air Blower

Material Handling Hose

(Specification 4691HA/4691HC) Nom. I.D. (In.) 1 1/2 2 2 1/2 3 3 1/2 4 5 6

(mm) 38.1 50.8 63.5 76.2 88.9 101.6 127.0 152.4

Nom. O.D. (In.) 2.08 2.58 3.08 3.64 4.14 4.64 5.74 6.74

(mm) 52.8 65.5 78.2 92.5 105.2 117.9 145.8 171.2

RECOMMENDED FOR: TEMPERATURE:

CONSTRUCTION:

Max. W.P. (psi) 130 125 110 100 85 75 55 40

(MPa) .90 .86 .76 .69 .59 .52 .38 .28

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 8.0 9.0 14.0 18.0 21.0 24.0 30.0 36.0

(mm) 203 229 356 457 533 610 762 914

Wt. Per Ft. (Lbs.) .89 1.13 1.43 1.89 2.17 2.44 3.82 4.52

(Kg) .40 .51 .65 .86 .98 1.11 1.73 2.05

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. X X X X X X X X

Gates Item No. 4691-0501 4691-0502 4691-0503 4691-0504 4691-0505 4691-0506 4691-0507 4691-0508

Conveying hot air up to 350°F from blower or compressor to storage tank used in the transfer of dry bulk commodities. Can also be used for transferring mild chemicals at ambient temperatures. -40°F to +350°F (-40°C to +177°C) for hot air service. NOTE: -40°F to +125°F (-40°C to +52°C) for mild chemical transfer. For chemicals above 125°F or suitability for use with a specific chemical, contact Denver Product Application at (303) 744-5070. Tube: Reinforcement: Cover:

Type P (EPDM). Black. Synthetic, high tensile textile with steel wire helix. Type P (EPDM). Black with yellow spiral stripe.

COUPLINGS:

5, 7 or 49. Block 49 (Cam and Groove) should not be used for compressed air service and are not recommended for high temperature service. Reference the Hose Coupling Section.

PACKAGING:

100' length coiled and wrapped in polyethylene.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Continuous transfer label. Example: “GATES® HOT AIR BLOWER 130 PSI (.90MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet for sizes through 4" and 200 feet for sizes above 4". If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 69

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

770SB

Material Handling Hose

(Specification 4691V) Nom. I.D. (In.) 1 1 1/4 1 1/2 2 2 1/2 3 4 5 6

(mm) 25.4 31.8 38.1 50.8 63.5 76.2 101.6 127.0 152.4

Nom. O.D. (In.) 1.39 1.64 1.89 2.39 2.89 3.39 4.39 5.53 6.53

(mm) 35.3 41.7 48.0 60.7 73.4 86.1 111.5 140.5 165.9

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 50 50 50 50 50 50 50 50 50

(MPa) .34 .34 .34 .34 .34 .34 .34 .34 .34

Suction (In. Hg) 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0

(mm Hg) 508 508 508 508 508 508 508 508 508

Min. Bend Radius (In.) 5.0 5.0 6.0 8.0 9.0 10.0 15.0 20.0 24.0

Tube: Reinforcement: Cover:

Gates Item No. 4691-0400 4691-0405 4691-0410 4691-0420 4691-0430 4691-0435 4691-0440 4691-0450 4691-0455

Type D3 (Natural Rubber). Black. Static conductive. Synthetic, high tensile textile with steel wire helix. Type D (SBR). Black corrugated with gray spiral stripe.

5, 6, 7 or 78. Reference the Hose Coupling Section. All lengths coiled and wrapped in polyethylene.

REMNANT LENGTHS:

Stock (X) or Minimum Order Qty. 400 ft. X X X X X X X X

-40°F to +150°F (-40°C to +66°C) continuous service.

COUPLINGS:

SPECIAL ORDER REQUIREMENTS:

(Kg) .22 .27 .31 .34 .41 .54 .68 1.24 1.47

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 50 ft. 50 ft.

Light duty vacuum service in industrial and maintenance applications conveying air, dust, fine particles, leaves, grass, etc.

PACKAGING: BRANDING:

(mm) 127 127 152 203 229 254 381 508 610

Wt. Per Ft. (Lbs.) .49 .59 .68 .75 .91 1.19 1.49 2.73 3.24

Continuous transfer label. Example: “GATES® 770SB LT WT Vacuum Service Only Made In U.S.A.” Special production runs require minimum order quantities of 400 feet for sizes through 4" and 200 feet for sizes above 4". If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 70

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

429W (Sand Blast)

Material Handling Hose

(Specification 4129A) Nom. I.D. (In.) 1/2 3/4 1 1 1 1/4 1 1/2 2

(mm) 12.7 19.1 25.4 25.4 31.8 38.1 50.8

Nom. O.D. (In.) 1.23 1.50 1.87 1.63 2.16 2.37 2.94

(mm) 31.2 38.1 47.5 41.4 54.9 60.2 74.7

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 150 150 150 135 120

(MPa) 1.03 1.03 1.03 1.03 1.03 .93 .83

Suction (In. Hg) 25.0 15.0 5.0 5.0 5.0 5.0 5.0

(mm Hg) 635 381 127 127 127 127 127

Min. Bend Radius (In.) 5.0 8.0 12.0 12.0 12.0 18.0 20.0

Tube: Reinforcement: Cover:

Gates Item No. 4129-0085 4129-0086 4129-0100 4129-0256 4129-0105 4129-0150 4129-0200

Type D3 (Natural Rubber). Black. Static conductive. Synthetic, high tensile textile. Type D (SBR). Black with yellow spiral stripe. All sizes are perforated.

PACKAGING:

50' length coiled and wrapped in polyethylene.

REMNANT LENGTHS:

Stock (X) or Minimum Order Qty. X X X X X X X

-40°F to +150°F (-40°C to +66°C) continuous service.

36. Reference the Hose Coupling Section.

SPECIAL ORDER REQUIREMENTS:

(Kg) .25 .32 .46 .32 .55 .62 .83

Standard Pack 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft.

Sand, shot blasting work and wherever abrasive materials are carried at high velocity.

COUPLINGS:

BRANDING:

(mm) 127 203 305 305 305 457 508

Wt. Per Ft. (Lbs.) .55 .70 1.01 .70 1.22 1.37 1.82

Continuous transfer label. Example: “GATES® 429W Sandblast 150 PSI (1.03MPa) WP Made In India” All sizes are wrapped construction, 50 foot maximum length. Special production runs require minimum order quantities of 600 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. None.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 71

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Master-Flex® 300 EPDM

Material Handling Hose

(Specification 7744) Nom. I.D. (In.) 1 1 1/4 1 1/2 2 2 1/2 3 4 6 *Working

Nom. Max. O.D. W.P. (mm) (In.) (mm) (psi) (MPa) 25.4 1.34 34.0 80 .55 31.8 1.61 40.9 70 .48 38.1 1.96 49.8 60 .41 50.8 2.49 63.2 60 .41 63.5 3.00 76.2 50 .34 76.2 3.60 91.4 50 .34 101.6 4.69 119.1 45 .31 152.4 6.86 174.2 35 .24 Pressure and Suction at +72°F (+22°C).

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Suction (In. Hg) 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0

(mm Hg) 711 711 711 711 711 711 711 711

Min. Bend Radius (In.) 4.0 5.0 6.0 9.0 11.0 12.0 17.0 27.0

(mm) 102 127 152 229 279 305 432 686

(Kg) .10 .14 .22 .31 .41 .47 .82 1.74

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. X X X X X X X X

Gates Item No. 7744-5201 7744-5202 7744-5203 7744-5204 7744-5205 7744-5206 7744-5207 7744-5208

Suction and discharge applications where lightweight, flexible hose is needed for transferring mild diluted chemicals and agricultural spray solutions. Good for septic service and transferring light abrasives. Reference Gates Chemical Resistance Table. -30°F to +140°F (-34°C to +60°C) continuous service. Tube: Reinforcement: Cover:

Type P (EPDM). Black. Polyethylene helix. Green. Type G (PVC). Black with green helix. Corrugated.

COUPLINGS:

1, 6, 7, 49 or 78. Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled and wrapped in polyethylene.

BRANDING:

Wt. Per Ft. (Lbs.) .23 .30 .49 .69 .91 1.03 1.81 3.84

Unlabeled.

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

None.

STANDARDS:

Tube:

None. RMA (Class B) Medium oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 72

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Master-Flex® 400

Material Handling Hose

(Specification 7744) Nom. I.D. (In.) 1 1/2 2 2 1/2 3 4 5 6 8 *Working

Nom. Max. O.D. W.P. (mm) (In.) (mm) (psi) (MPa) 38.1 1.88 47.8 40 .28 50.8 2.41 61.2 35 .24 63.5 2.98 75.7 35 .24 76.2 3.87 98.3 30 .21 101.6 4.65 118.1 30 .21 127.0 5.77 146.6 30 .21 152.4 6.86 174.2 25 .17 203.2 9.10 231.1 25 .17 Pressure and Suction at +72°F (+22°C).

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Suction (In. Hg) 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0

(mm Hg) 711 711 711 711 711 711 711 711

Min. Bend Radius (In.) 3.0 4.0 5.0 6.0 8.0 9.0 12.0 16.0

(mm) 76 102 127 152 203 229 305 406

Stock (X) or Minimum Order Qty. X X X X X 1,000 ft. X X

Gates Item No. 7744-6102 7744-6103 7744-6104 7744-6105 7744-6106 7744-6107 7744-6108 7744-6209

-30°F to +140°F (-34°C to +60°C) continuous service. Tube:

Type C (Nitrile) blend. Static conductive. Type D (SBR). Rigid PVC helix. Black. Type G (PVC). Black with gray helix. Corrugated.

COUPLINGS:

1, 6, 7, 49 or 78. Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled and wrapped in polyethylene.

BRANDING:

(Kg) .17 .25 .35 .48 .76 1.09 1.44 2.60

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 50 ft.

Transfer of bulk materials via suction, pneumatic or gravity systems where abrasion resistance is the primary requirement and a static conductive hose is needed. Can also be used for vacuum or ducting service.

Reinforcement: Cover:

SPECIAL ORDER REQUIREMENTS:

Wt. Per Ft. (Lbs.) .38 .54 .77 1.05 1.68 2.40 3.18 5.73

Unlabeled. Special production runs require minimum order quantities of 1,000 feet per size. No deviations allowed to above product.

REMNANT LENGTHS:

None.

STANDARDS:

Tube:

RMA (Class B) Medium oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 73

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

1000 MP/Mine Spray

Mining Hose

(Specification 3619M) Nom. I.D. (In.) 1/2 1/2 1/2 3/4 3/4 3/4 3/4 1 1 1 1 1 1/4 1 1/4 1 1/4 1 1/4 1 1/2 1 1/2 1 1/2 1 1/2 2 2 2

(mm) 12.7 12.7 12.7 19.1 19.1 19.1 19.1 25.4 25.4 25.4 25.4 31.8 31.8 31.8 31.8 38.1 38.1 38.1 38.1 50.8 50.8 50.8

Nom. O.D. (In.) .84 .84 .84 1.10 1.10 1.10 1.10 1.42 1.42 1.42 1.42 1.69 1.69 1.69 1.69 1.92 1.92 1.92 1.92 2.45 2.45 2.45

(mm) 21.3 21.3 21.3 27.9 27.9 27.9 27.9 36.1 36.1 36.1 36.1 42.9 42.9 42.9 42.9 48.8 48.8 48.8 48.8 62.0 62.0 62.0

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000

(MPa) 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90 6.90

Suction (In. Hg) 30.0 30.0 30.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 20.0 20.0 20.0 20.0 15.0 15.0 15.0 15.0 10.0 10.0 10.0

(mm Hg) 762 762 762 635 635 635 635 635 635 635 635 508 508 508 508 381 381 381 381 254 254 254

Min. Bend Radius (In.) 5.0 5.0 5.0 8.0 8.0 8.0 8.0 11.0 11.0 11.0 11.0 16.0 16.0 16.0 16.0 18.0 18.0 18.0 18.0 25.0 25.0 25.0

(mm) 127 127 127 203 203 203 203 279 279 279 279 406 406 406 406 457 457 457 457 635 635 635

Wt. Per Ft. (Lbs.) .29 .29 .29 .43 .43 .43 .43 .66 .66 .66 .66 .81 .81 .81 .81 .98 .98 .98 .98 1.36 1.36 1.36

(Kg) .13 .13 .13 .20 .20 .20 .20 .30 .30 .30 .30 .37 .37 .37 .37 .45 .45 .45 .45 .62 .62 .62

Standard Pack 50 ft. 100 ft. Bulk 50 ft. 50 ft. 100 ft. Bulk 50 ft. Bulk 100 ft. 50 ft. Bulk 50 ft. 100 ft. Bulk 100 ft. 50 ft. Bulk 50 ft. 100 ft. Bulk 100 ft. 50 ft. Bulk 50 ft. 100 ft. Bulk 100 ft. 100 ft. 50 ft. Bulk 50 ft.

Stock (X) or Minimum Order Qty. X X 5,000 ft. X X 3,000 ft. 3,000 ft. X 3,000 ft. X 3,000 ft. X 3,000 ft. X 3,000 ft. X 3,000 ft. X 3,000 ft. X X 3,000 ft.

Gates Item No. 3619-0699 3619-0716 3619-0761 3619-0700 3619-0721 3619-0762 3619-0789 3619-0701 3619-0763 3619-0786 3619-0790 3619-0702 3619-0764 3619-0787 3619-0791 3619-0708 3619-0765 3619-0788 3619-0792 3619-0745 3619-0760 3619-0766

High-pressure water service in underground mining applications and hot water washdown service. Air service working pressure is 300 PSI for all sizes. -40°F to +212°F (-40°C to +100°C) service range. Tube: Reinforcement: Cover:

Type P (EPDM). Black. Braided, high tensile steel wire. Type C2 (Modified Nitrile). Yellow (non-marking). All sizes are perforated.

COUPLINGS:

72 Gates Power Crimp®, 74 Gates MegaCrimp® (1/2" through 1 1/4"), 14, 15, or 19 (up to 300 PSI only). Reference the Hose Coupling Section.

PACKAGING:

1/2" through 2": 50' and 100' lengths, one length coiled in a carton. 1/2" x 50': Packaged 1200' per bulk carton, each length coiled and tied. 3/4" x 100': Packaged 1000' per bulk carton, each length coiled and tied. 3/4" x 50': Packaged 1000' per bulk carton, each length coiled and tied. 1" x 100': Packaged 700' per bulk carton, each length coiled and tied. 1" x 50': Packaged 700' per bulk carton, each length coiled and tied. 1 1/4" x 100': Packaged 600' per bulk carton, each length coiled and tied. 1 1/4" x 50': Packaged 600' per bulk carton, each length coiled and tied. 1 1/2" x 100': Packaged 400' per bulk carton, each length coiled and tied. 1 1/2" x 50': Packaged 400' per bulk carton, each length coiled and tied. 2" x 50': Packaged 200' per bulk carton, each length coiled and tied.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous transfer label. Example: “GATES® 1000 MP/Mine Spray 1 1/2 INCH (38.1mm) 1000 PSI (6.90MPa) WP 300 PSI (2.07MPa) MAX Air Service MSHA IC-11C MADE IN INDIA” Special production runs require minimum order quantities of 5,000 feet for 1/2" and 3,000 feet for 3/4" through 2". Contact Gates Corporation for lead times. None. Cover:

Meets MSHA 30 CFR 18.65. Flame resistant.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 74

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Longwall Mine Emulsion

Mining Hose

(Specification 3619MC/3619MY) Black Cover (3619MC) Nom. I.D. (In.) 2 1/2 2 1/2 3 3

(mm) 63.5 63.5 76.2 76.2

Nom. O.D. (In.) 3.34 3.34 3.91 3.91

(mm) 84.8 84.8 99.3 99.3

Max. W.P. (psi) 1000 1000 1000 1000

(MPa) 6.90 6.90 6.90 6.90

Suction (In. Hg) 10.0 10.0 10.0 10.0

(MPa) 6.90 6.90

Suction (In. Hg) 10.0 10.0

(mm Hg) 254 254 254 254

Min. Bend Radius (In.) 20.0 20.0 20.0 20.0

(mm Hg) 254 254

Min. Bend Radius (In.) 20.0 20.0

(mm) 508 508 508 508

Wt. Per Ft. (Lbs.) 2.90 2.90 4.05 4.05

(Kg) 1.32 1.32 1.84 1.84

Standard Pack 50 ft. 100 ft. 50 ft. 100 ft.

Stock (X) or Minimum Order Qty. X X X X

Gates Item No. 3619-0809 3619-0811 3619-0810 3619-3531

(mm) 508 508

Wt. Per Ft. (Lbs.) 4.05 4.05

(Kg) 1.84 1.84

Standard Pack 50 ft. 100 ft.

Stock (X) or Minimum Order Qty. X X

Gates Item No. 3619-0051 3619-3530

Yellow Cover (3619MY) Nom. I.D. (In.) 3 3

(mm) 76.2 76.2

Nom. O.D. (In.) 3.91 3.91

(mm) 99.3 99.3

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 1000 1000

Flexible connections in high pressure water distribution and emulsion systems used in a variety of industries. The thick cover meets MSHA’s self-extinguishing requirements, and is designed for the rough mining environment. -40°F to +212°F (-40°C to +100°C) normal service. Tube: Reinforcement: Cover:

Type A (Neoprene). Black. Braided, high tensile steel wire. Type C2 (Specially compounded elastomer). Black. Self-extinguishing to meet MSHA requirements. Type C4 (Modified Nitrile). Yellow (non-marking). Self-extinguishing to meet MSHA requirements.

COUPLINGS:

14, 15 or reusable male couplings (Wildman). Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled in a carton.

BRANDING:

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous ink brand. Example: “GATES® LONGWALL MINE EMULSION 3 INCH (76.2mm) 1000 PSI (6.90MPa) W.P. MSHA 2G-IC-11C MADE IN INDIA”. Continuous ink brand. Example: “GATES® LONGWALL MINE EMULSION 3 INCH (76.2mm) 1000 PSI (6.90MPa) W.P. MSHA IC-11C MADE IN INDIA” (yellow cover only) Special production runs require minimum order quantities of 600 feet per size. None. Tube: Cover:

RMA (Class B) Medium oil resistance. Meets MSHA 30 CFR 18.65. Flame resistant.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 75

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Scorpion™

Mining Hose

(Specification 3618MT) Nom. I.D. (In.) 1 1/2 2 2 1/2 3 4

(mm) 38.1 50.8 63.5 76.2 101.6

Nom. O.D. (In.) 2.02 2.62 3.12 3.64 4.79

(mm) 51.3 66.6 79.3 92.5 121.7

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 600 600 600 600 600

(MPa) 4.13 4.13 4.13 4.13 4.13

Suction (In. Hg) — — — — —

(mm Hg) — — — — —

Min. Bend Radius (In.) 12.0 16.0 18.0 20.0 25.0

(mm) 305 406 457 508 635

Wt. Per Ft. (Lbs.) 1.13 1.51 1.89 2.46 4.10

Gates Item No. 3618-0311 3618-0312 3618-0313 3618-0314 3618-0315

-40°F to +275°F (-40°C to +135°C). Tube: Reinforcement: Cover:

Type J (CPE). Black. Braided, high tensile steel wire. Type J (CPE). Black. All sizes perforated.

14, 15, 18, Dixon Boss Clamps all sizes.

PACKAGING:

50' per carton +/- 10'. Maximum of 2 pieces. Minimum length 10'.

SPECIAL ORDER REQUIREMENTS:

Stock (X) or Minimum Order Qty. X X X X X

High pressure and high temperature air hose used on industrial, construction, pneumatic mining and drilling applications requiring a wire braided hose with a high degree of hot air resistance.

COUPLINGS:

BRANDING:

(Kg) .51 .68 .86 1.12 1.86

Standard Pack 50 ft. 50 ft. 50 ft. 50 ft. 50 ft.

Continuous transfer label. Example: “GATES® SCORPION™ HI-TEMP AIR DRILL 600PSI (4.13 MPa) WP MADE IN USA” Special production runs require minimum order quantities of 600 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity.

REMNANT LENGTHS:

None.

STANDARDS:

Tube:

RMA (Class B) Medium oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 76

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Scorpion™ X-Treme

Mining Hose

(Specification 3618HT) Nom. I.D. (In.) 1 1/2 2 2 1/2 3 4

(mm) 38.1 50.8 63.5 76.2 101.6

Nom. O.D. (In.) 2.02 2.62 3.12 3.77 4.79

(mm) 51.3 66.6 79.3 95.8 121.7

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 600 600 600 600 600

(MPa) 4.13 4.13 4.13 4.13 4.13

Suction (In. Hg) — — — — —

(mm Hg) — — — — —

Min. Bend Radius (In.) 12.0 16.0 18.0 20.0 25.6

(mm) 305 406 457 508 650

Wt. Per Ft. (Lbs.) 1.07 1.46 1.81 2.83 3.96

Gates Item No. 3618-0306 3618-0307 3618-0308 3618-0309 3618-0310

-40°F to +300°F (-40°C to +149°C). Tube: Reinforcement: Cover:

Type B1 (Specially compounded elastomer). Black. Braided, high tensile steel wire. Type J (CPE). Black. All sizes perforated.

14, 15, 18, Dixon Boss Clamps all sizes.

PACKAGING:

50' per carton +/- 10'. Maximum of 2 pieces. Minimum length 10'.

SPECIAL ORDER REQUIREMENTS:

Stock (X) or Minimum Order Qty. X X X X X

High pressure and high temperature air hose used on industrial, construction, pneumatic mining and drilling applications requiring a wire braided hose with extremely high temperature hot air and hot oil resistance.

COUPLINGS:

BRANDING:

(Kg) .49 .66 .82 1.28 1.80

Standard Pack 50 ft. 50 ft. 50 ft. 50 ft. 50 ft.

Continuous transfer label. Example: “GATES® SCORPION™ X-TREME HI-TEMP AIR DRILL 600PSI (4.13 MPa) WP MADE IN USA” Special production runs require minimum order quantities of 600 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity.

REMNANT LENGTHS:

None.

STANDARDS:

Tube:

RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 77

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

18MB Air Drill

Mining Hose

(Specification 3618/3618GL) Nom. I.D. (In.) 3/4 1 1 1/4 1 1/2 2 2 1/2 2 1/2 3 4

(mm) 19.1 25.4 31.8 38.1 50.8 63.5 63.5 76.2 101.6

Nom. O.D. (In.) 1.28 1.55 1.80 2.21 2.77 3.46 3.46 3.97 5.06

(mm) 32.5 39.4 45.7 56.1 70.4 87.9 87.9 100.8 128.5

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 500 500 500 500 600 500 500 500 500

(MPa) 3.45 3.45 3.45 3.45 4.14 3.45 3.45 3.45 3.45

Suction (In. Hg) 25.0 25.0 15.0 15.0 15.0 10.0 10.0 10.0 10.0

(mm Hg) 635 635 381 381 381 254 254 254 254

Min. Bend Radius (In.) 6.0 8.0 10.0 12.0 14.0 30.0 30.0 36.0 47.6

(mm) 152 203 254 305 356 762 762 914 1219

Wt. Per Ft. (Lbs.) .60 .80 .95 1.26 1.99 3.04 3.04 3.69 5.77

(Kg) .27 .36 .43 .57 .90 1.38 1.38 1.67 2.62

Standard Pack 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 50 ft. 60 ft. 50 ft. 50 ft.

Stock (X) or Minimum Order Qty. X X 5,000 ft. X X X X X X

Gates Item No. 3618-0011 3618-0021 3618-0031 3618-0041 3618-0051 3618-0201 3618-0205 3618-0215 3618-0225

Extra heavy duty, high pressure use on industrial, construction and pneumatic mining applications requiring wire braided hose with an oil resistant tube and abrasion resistant cover. -30°F to +212°F (-34°C to +100°C) continuous service. Tube: Reinforcement: Cover:

Type A (Neoprene). Black. Braided, high tensile steel wire. Type C2 (Modified Nitrile). Gray with yellow stripe. All sizes are perforated. For 3/4" through 1 1/4" sizes only. Type D3 (Natural Rubber). Gray with yellow stripe. All sizes are perforated. For 1 1/2" through 4" sizes only.

COUPLINGS:

14, 15 or 18. Reference the Hose Coupling Section.

PACKAGING:

3/4" through 1 1/2": Packaged 49' - 50' length coiled in carton. 2" though 4": Packaged 48' - 50' length coiled in carton. 2 1/2" x 60': Packaged 60' length coiled in carton.

BRANDING:

Continuous transfer label. Example: “GATES® 18MB PREMIUM AIR DRILL 500 PSI (3.45MPa) WP MADE IN USA”

SPECIAL ORDER REQUIREMENTS:

Special production runs require minimum order quantities of 5,000 feet for 3/4" through 1 1/4" and 600 feet for 1 1/2" and larger.

REMNANT LENGTHS:

None.

STANDARDS:

Tube:

RMA (Class B) Medium oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 78

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

500 MP Air Drill

Mining Hose

(Specification 3618/3618Y) Black Cover (3618) Nom. I.D. (In.) (mm) 3/4 19.1 1 25.4 1 1/4 31.8 1 1/2 38.1 2 50.8 2 1/2 63.5 3 76.2 NOTE: For 4" I.D.

Nom. O.D. (In.) (mm) 1.11 28.2 1.45 36.6 1.74 44.2 1.99 50.6 2.50 63.5 3.14 79.8 3.67 93.2 see 18MB.

Max. W.P. (psi) 500 500 500 500 500 500 500

(MPa) 3.45 3.45 3.45 3.45 3.45 3.45 3.45

Suction (In. Hg) 25.0 25.0 15.0 15.0 15.0 10.0 10.0

(MPa) 3.45 3.45 3.45 3.45 3.45 3.45 3.45

Suction (In. Hg) 25.0 25.0 15.0 15.0 15.0 10.0 10.0

(mm Hg) 635 635 381 381 381 254 254

Min. Bend Radius (In.) 6.0 8.0 10.0 12.0 14.0 30.0 36.0

(mm Hg) 635 635 381 381 381 254 254

Min. Bend Radius (In.) 6.0 8.0 10.0 12.0 14.0 30.0 36.0

(mm) 152 203 254 305 356 762 914

Wt. Per Ft. (Lbs.) .41 .66 .86 .98 1.40 2.16 2.73

(mm) 152 203 254 305 356 762 914

Wt. Per Ft. (Lbs.) .41 .65 .85 .96 1.43 2.19 2.78

(Kg) .19 .30 .39 .45 .64 .98 1.24

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. X X X X X X X

Gates Item No. 3618-0801 3618-0802 3618-0803 3618-0804 3618-0805 3618-0806 3618-0807

(Kg) .19 .30 .39 .45 .65 .99 1.26

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. X X X X X X X

Gates Item No. 3618-0808 3618-0809 3618-0810 3618-0811 3618-0812 3618-0813 3618-0814

Yellow Cover (3618Y) Nom. I.D. (In.) (mm) 3/4 19.1 1 25.4 1 1/4 31.8 1 1/2 38.1 2 50.8 2 1/2 63.5 3 76.2 NOTE: For 4" I.D.

Nom. O.D. (In.) (mm) 1.11 28.2 1.45 36.6 1.74 44.2 1.99 50.6 2.50 63.5 3.14 79.8 3.67 93.2 see 18MB.

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 500 500 500 500 500 500 500

Heavy-duty, high pressure use on industrial, construction and pneumatic mining applications requiring wire braided hose with an oil resistant tube and abrasion resistant cover. -22°F to +180°F (-30°C to +82°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Braided, high tensile steel wire. Type C2 (Modified Nitrile). Yellow with black spiral stripe. All sizes are perforated. Type D3 (Natural Rubber). Black with yellow spiral stripe.

COUPLINGS:

14, 15 or 18. Reference the Hose Coupling Section.

PACKAGING:

100' length coiled in a carton.

BRANDING:

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous transfer. Example: “GATES® 500 MP/Air Drill 3/4 INCH (19.1mm) 500 PSI (3.45MPa) WP MADE IN INDIA” Continuous transfer. Example: “GATES® 500 MP/Air Drill 3/4 INCH (19.1mm) 500 PSI (3.45MPa) WP MSHA IC-11C MADE IN INDIA” (yellow cover only). Special production runs require minimum order quantities of 3,000 feet for 3/4" through 1 1/2" and 2,500 feet for 2" and larger. None. Tube: Cover:

RMA (Class B) Medium oil resistance. Meets MSHA 30 CFR 18.65. Flame resistant. Yellow cover only.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 79

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

GATES CERTIFIED ROUGHNECK DISTRIBUTORS Gates Rotary Drilling, Vibrator, Cementing, Sour Service, Choke and Kill, Motion Compensator and Decoker oilfield hoses shown in this section have couplings attached by a Gates Certified Roughneck Distributor from hose already in their stock. The advantage is that hose from the Roughneck Distributorâ&#x20AC;&#x2122;s stock can be cut to the customerâ&#x20AC;&#x2122;s specified length. Couplings are then swaged-on, tested to API 7K standards and then shipped all in a matter of just hours! This greatly reduces the lead time required to supply product meeting your specific needs. The resulting hose assembly far exceeds Gates standards for coupling pull and burst pressure tests for added safety. Contact your nearest Roughneck Distributor for price and availability. Du-Tex, Inc. 134 44th Street Corpus Christi, Texas 78405 www.dutex.com Ph. 361-887-9807 F. 361-887-0812 Mike Ray dutex@msn.com Power Product Technologies Inc. 6200 North Washington Bldg. 1, Unit 1 Denver, Colorado 80216 www.ppt-hose-tech.com Ph. 303-286-7724 F. 303-286-7311 Adam Stewart astewart@ppt-hose-tech.com Robsco, Inc. 4749 Eastpark Drive Houston, Texas 77028 www.robsco.com Ph. 713-672-1777 F. 713-672-1956 Scott Collins scott@robsco.com Frank Navarro frank@robsco.com Gates A.E. Hydraulics Pte Ltd 40 Gul Circle Jurong Industrial Estate Singapore 629575 www.aehydraulic.com Ph. (65) 6861 7322 F. (65) 6861 7631 YK Chua ykchua@aehydraulic.com

Gates Fleximak Ltd. Mod. 215 731b Street P.O. Box 61046 Jebel Ali, Dubai United Arab Emirates www.gatesfleximak.com Ph. 971 4 8813900 F. 971 4 8813902 Tony Rogowsky info@gatesfleximak.com Gates de Mexico, S.A. de C.V. Lerma Hose Plant Blvd. Aeropuerto Miguel Aleman No. 164 52000 Lerma Edo. De Mexico, Mexico www.gates.com.mx Ph. 52 (55) 2000-2777 F. 52 (55) 2000-2727 Antonio Santibanez as1108@gates.com GS Hydro Norge A/S Stavanger Branch Fabrikkveien 26 4033 Stavanger Norway www.gshydro.com Ph. (47) 51 95 96 40 F. (47) 51 95 96 41 Espen Myhre espen.myhre@gshydro.no Hydrasun Limited 392 King Street Aberdeen AB24 3BU United Kingdom www.hydrasun.com Ph. 44 (0) 1224 618618 F. 44 (0) 1224 618612 Bill Anderson bill.anderson@hydrasun.com

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 80

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Black Gold

Oilfield Hose Rotary/Vibrator Drilling – Grade D or Motion Compensator 5,000 psi W.P. – 10,000 Test – 12,500 Minimum Burst Nom. I.D.

Nom. O.D.

Min. Bend Radius (Inches)

Wt. per Ft. of hose (Lbs)

2-1/2

4.14

4.61

3-1/2 4

5.25 5.61

(Specification 4774PE) Swage Cplg. Wts. Each (Lbs) 33

Maximum length of hose (Feet)

Safety Clamp & Chain Part No.

9.8

Coupling Threads API (T) (In.) 3"

7361-0825

10.8

44.5

7361-0830

54 54

12.8 13.4

4" 5"

47 55

90 90

7361-0835 7361-0840

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

COUPLINGS:

Flexible connection between standpipe and swivel (Rotary Drilling) or between pump and standpipe (Rotary Vibrator) for pumping mud at extra high pressure in oil drilling and exploration work. Meets the high demands of directional drilling and down linking with negative pressure pulses and elevated temperatures. Motion Compensator hose is used for stabilization of rotary drilling and pumping equipment against vertical wave action on offshore drill platforms. The Motion Compensator hose is not recommended for phosphate ester fluids. -4°F to +180°F (-20°C to +82°C) continuous service. Type C3 (Modified Nitrile). 3/16" thick. Black. Specially compounded for handling abrasive, corrosive and oily drilling mud. Reinforcement: Multiple layers of polyester cord over tube. Multiple layers of “close wound”, high tensile steel cables, with one layer of adhesion fabric placed between cable layers. Multiple layers of reinforcement under cover. Type C4 (Modified Nitrile). Black. Specially compounded UltraBrasion cover is resistant Cover: to abrasion, corrosion, cutting, gouging, oil and weather.

Tube:

Swaged – API male line pipe threads standard. Gates recommends butt-welded couplings. Couplings can be supplied with your choice of end fittings. Please contact your nearest Roughneck Distributor for more detailed information. (Refer to Roughneck Distributor list at the beginning of this section). NOTE: FIELD WELDING OF FITTINGS TO COUPLING IS NOT RECOMMENDED.

FITTINGS:

PACKAGING: BRANDING:

CERTIFICATION/ STANDARDS:

OPTIONAL:

Each length packaged in a heavy-duty wooden crate. One continuous longitudinal yellow transfer label (with serial number and code date embossed). Example: “GATES® BLACK GOLD® ROTARY VIBRATOR 3 INCH MAX WP 5000 PSI API SPEC 7K TESTED TO 10000 PSI GRADE D FSL 1 TEMP RANGE 1 ISO 14693 LICENSE 7K-0003 MADE IN U.S.A.” API (American Petroleum Institute) Spec 7K. Coupling/Mat’l Traceability (Additional Cost) ISO 14693 Letter of Conformance (Additional Cost) Test Certificates 3rd Party Witness Test (Additional Cost) ABS/CDS Type Approval Accessories such as SAFETY CLAMPS, HOSE LIFT EYE & COLLAR CLAMP and STAINLESS STEEL ARMOR are available.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 81

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Black Gold

Oilfield Hose Rotary/Vibrator Drilling – Grade E 7,500 psi W.P. – 15,000 Test – 18,750 Minimum Burst

(Specification 4773PE)

Nom. I.D. 2-1/2

Nom. O.D. 5.16

Min. Bend Radius (Inches) 48

Wt. per Ft. of hose (Lbs) 20.2

Swage Cplg. Wts. Each (Lbs) 62

Maximum length of hose (Feet) 90

Safety Clamp & Chain Part No. 7361-0835

5.66

22.6

7361-0840

3-1/2 4

6.04 6.48

54 60

24.1 25.8

75 90

90 90

7361-0845 7361-0850

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

COUPLINGS:

Flexible connection between standpipe and swivel (Rotary Drilling) or between pump and standpipe (Rotary Vibrator) for pumping mud at extra high pressure in oil drilling and exploration work. Meets the high demands of directional drilling and down linking with negative pressure pulses and elevated temperatures. -4°F to +180°F (-20°C to +82°C) continuous service. Type C3 (Modified Nitrile). 3/16" thick. Black. Specially compounded for handling abrasive, corrosive and oily drilling mud. Reinforcement: Multiple layers of polyester cord over tube. Multiple layers of “close wound”, high tensile plated steel cables, with one layer of adhesion fabric placed between cable layers. Multiple layers of reinforcement under cover. Type C4 (Modified Nitrile). Black. Specially compounded UltraBrasion cover is resistant Cover: to abrasion, corrosion, cutting, gouging, oil and weather.

Tube:

Swaged – API 7K hose assemblies with working pressures exceeding 5,000 psi, the end fitting will be buttwelded onto the hose coupling. Couplings can be supplied with your choice of end fitting. Please contact your nearest Roughneck Distributor for more detailed information. (Refer to Roughneck Distributor list at the beginning of this section). NOTE: FIELD WELDING OF FITTINGS TO COUPLING IS NOT RECOMMENDED.

FITTINGS:

PACKAGING: BRANDING:

CERTIFICATION/ STANDARDS:

OPTIONAL:

Each length packaged in a heavy-duty wooden crate. One continuous longitudinal yellow transfer label (with serial number and code date embossed). Example: “GATES® BLACK GOLD® ROTARY VIBRATOR 3INCH MAX WP 7500 PSI API SPEC 7K TESTED TO 15000 PSI GRADE E FSL 1 TEMP RANGE 1 ISO 14693 LICENSE 7K-0003 MADE IN U.S.A.” API (American Petroleum Institute) Spec 7K. Coupling/Mat’l Traceability (Additional Cost) ISO 14693 Letter of Conformance (Additional Cost) Test Certificates 3rd Party Witness Test (Additional Cost) ABS/CDS Type Approval Accessories such as SAFETY CLAMPS, HOSE LIFT EYE & COLLAR CLAMP and STAINLESS STEEL ARMOR are available.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 82

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Black Gold

Oilfield Hose Cementing (Nitrile Tube) 5,000 psi W.P. – 10,000 Test – 12,500 Minimum Burst Nom. I.D.

Nom. O.D.

Min. Bend Radius (Inches)

2-1/2

4.14

4.61

3-1/2 4

5.25 5.61

54 54

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

COUPLINGS:

Wt. per Ft. of hose (Lbs)

(Specification 4774PE) Swage Cplg. Wts. Each (Lbs) 33

Maximum length of hose (Feet)

Safety Clamp & Chain Part No.

9.8

Coupling Threads API (T) (In.) 3"

7361-0825

10.8

44.5

7361-0830

12.8 13.4

4" 5"

47 55

90 90

7361-0835 7361-0840

Used as a flexible connection between the cementing pump manifold and cementing head for conveyance of cement slurries at high pressure. -4°F to +180°F (-20°C to +82°C) continuous service. Tube:

Type C3 (Modified Nitrile). 3/16" thick. Black. Specially compounded for handling abrasion and corrosion. Reinforcement: Multiple layers of “close wound”, high tensile steel cables with one layer of adhesion fabric placed between cable layers. Multiple layers of reinforcement under cover. Cover: Type C4 (Modified Nitrile). Black. Specially compounded UltraBrasion cover is resistant to abrasion, corrosion, cutting, gouging, oil and weather.

Swaged – API male line pipe threads standard. Gates recommends butt-welded couplings. Couplings can be supplied with your choice of end fitting. Please contact your nearest Roughneck Distributor for more detailed information. (Refer to Roughneck Distributor list at the beginning of this section). NOTE: FIELD WELDING OF FITTINGS TO COUPLING IS NOT RECOMMENDED.

FITTINGS:

PACKAGING: BRANDING:

CERTIFICATION/ STANDARDS:

OPTIONAL:

Each length packaged in a heavy-duty wooden crate. One continuous longitudinal yellow transfer label (with serial number and code date embossed). Example: “GATES® BLACK GOLD® CEMENTING 4 INCH MAX WP 5000 PSI TESTED TO 10000 PSI FSL 0 TEMP RANGE 1 ISO 14693 LICENSE 7K-0003 MADE IN U.S.A.” API (American Petroleum Institute) Spec 7K. Coupling/Mat’l Traceability (Additional Cost) ISO 14693 Letter of Conformance (Additional Cost) Test Certificates 3rd Party Witness Test (Additional Cost) ABS/CDS Type Approval Accessories such as SAFETY CLAMPS, HOSE LIFT EYE & COLLAR CLAMP and STAINLESS STEEL ARMOR are available.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 83

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Black Gold

Oilfield Hose Cementing (Nitrile Tube) 10,000 psi W.P. – 15,000 Test. – 22,500 Minimum Burst

(Specification 4773PE)

Nom. I.D. 2-1/2

Nom. O.D. 5.16

Min. Bend Radius (Inches) 48

Wt. per Ft. of hose (Lbs) 20.2

Swage Cplg. Wts. Each (Lbs) 62

Maximum length of hose (Feet) 90

Safety Clamp & Chain Part No. 7361-0835

5.66

22.6

7361-0840

3-1/2

6.04

24.1

7361-0845

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

COUPLINGS:

Used as a flexible connection between the cementing pump manifold and cementing head for conveyance of cement slurries at high pressure. -4°F to +180°F (-20°C to +82°C) continuous service. Tube:

Type C3 (Modified Nitrile). 3/16" thick. Black. Specially compounded for handling abrasion and corrosion. Reinforcement: Multiple layers of "close wound" high tensile plated steel cables, with one layer of adhesion fabric placed between cable layers. Multiple layers of reinforcement under cover. Cover: Type C4 (Modified Nitrile). Black. Specially compounded UltraBrasion cover is resistant to abrasion, corrosion, cutting, gouging, oil and weather.

FITTINGS:

PACKAGING: BRANDING:

CERTIFICATION/ STANDARDS:

OPTIONAL:

Each length packaged in a heavy-duty wooden crate. One continuous longitudinal yellow transfer label (with serial number and code date embossed). Example: “GATES® BLACK GOLD® CEMENTING 4 INCH MAX WP 10000 PSI TESTED TO 15000 PSI FSL 0 TEMP RANGE 1 ISO 14693 LICENSE 7K-0003 MADE IN U.S.A.” API (American Petroleum Institute) Spec 7K. Coupling/Mat’l Traceability (Additional Cost) ISO 14693 Letter of Conformance (Additional Cost) Test Certificates 3rd Party Witness Test (Additional Cost) ABS/CDS Type Approval Accessories such as SAFETY CLAMPS, HOSE LIFT EYE & COLLAR CLAMP and STAINLESS STEEL ARMOR are available.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 84

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Black Gold

Oilfield Hose Cementing (Fluoroelastomer Tube) 15,000 psi W.P. – 22,500 Test – 33,750 Minimum Burst Nom. I.D. 2-1/2 3

Nom. O.D. 5.66 6.16

Min. Bend Radius (Inches) 60 60

RECOMMENDED FOR: TEMPERATURE:

Wt. per Ft. of hose (Lbs) 29.4 33.2

Swage Cplg. Wts. Each (Lbs) 130 172

(Specification 4758L) Maximum length of hose (Feet) 90 90

Safety Clamp & Chain Part No. 7361-0840 7361-0845

Used as a flexible connection between the cementing pump manifold and cementing head for conveyance of cement slurries at high pressure. -4°F to +212°F (-20°C to +100°C) continuous service.

CONSTRUCTION:

Type V (Fluoroelastomer). Black. Excellent resistance to abrasion and corrosion. Tube: Reinforcement: Multiple layers of "close wound", high tensile plated steel cables to withstand flexing and high pressures encountered in offshore operations. Multiple layers of reinforcement under cover. Cover: Type C4 (Modified Nitrile). Black. Specially compounded UltraBrasion cover is resistant to abrasion, corrosion, cutting, gouging, oil and weather.

COUPLINGS:

Special Built-In supplied with your choice of end fittings. Please contact your nearest Roughneck Distributor for more detailed information. (Refer to Roughneck Distributor list at the beginning of this section). NOTE: FIELD WELDING OF FITTINGS TO COUPLING IS NOT RECOMMENDED.

FITTINGS:

PACKAGING: BRANDING:

CERTIFICATION/ STANDARDS:

OPTIONAL:

Each length packaged in a heavy-duty wooden crate. One continuous longitudinal yellow transfer label (with serial number and code date embossed). Example: “GATES® BLACK GOLD® CEMENTING 2-1/2 INCH MAX WP 15000 PSI TESTED TO 22500 PSI MADE IN U.S.A.” Coupling/Mat’l Traceability (Additional Cost) Letter of Conformance (Additional Cost) Test Certificates 3rd Party Witness Test (Additional Cost) Accessories such as SAFETY CLAMPS, HOSE LIFT EYE & COLLAR CLAMP and STAINLESS STEEL ARMOR are available.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 85

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Black Gold

Oilfield Hose Cementing (Nitrile Tube) 5,000 psi W.P. – 10,000 Test – 12,500 Minimum Burst Nom. I.D. 2

Nom. O.D. 2.80

Min. Bend Radius (Inches) 36

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

COUPLINGS:

FITTINGS:

PACKAGING: BRANDING:

CERTIFICATION/ STANDARDS:

OPTIONAL:

Wt. per Ft. of hose (Lbs) 4.63

Crimped Cplg. Wts. (Lbs.) 1502 Hammer Union Assy. Female Male Sub/Seal Sub/Nut 7341-1569 7341-1571 (7.8 Lbs.) (17.7 Lbs.)

(Specification 4651ZL) Maximum length of hose (Feet) 200

Safety Clamp & Chain Part No. 7361-6550

Used as a flexible connection between the cementing pump manifold and cementing head for conveyance of cement slurries at high pressure. -4°F to +250°F (-20°C to +121°C) continuous service. Tube: Type C (Nitrile). Black. Specially compounded for handling abrasion and corrosion. Reinforcement: Multiple layers of spiraled high tensile steel wire. Cover: Type A (Neoprene). Black. Oil and abrasion resistant. Crimped – Gates GSH™ with integral 2” Fig. 1502 hammer union couplings with male sub/nut and female sub/seal. Couplings can be supplied with your choice of end fittings. Please contact your nearest Roughneck Distributor for more detailed information. (Refer to Roughneck Distributor list at the beginning of this section). NOTE: FIELD WELDING OF FITTINGS TO COUPLING IS NOT RECOMMENDED. GSH with Integral 2” Fig. 1502 Hammer Unions

Each length packaged in a carton. One continuous longitudinal yellow transfer label (with serial number and code date embossed). Example: “GATES® BLACK GOLD® CEMENTING NOT FOR SOUR SERVICE 2 INCH MAX WP 5000 PSI TESTED TO 10000 PSI FSL 0 TEMP RANGE III ISO 14693 LICENSE 7K-0003 MADE IN U.S.A.” API (American Petroleum Institute) Spec 7K. Coupling/Mat’l Traceability (Additional Cost) ISO 14693 Letter of Conformance (Additional Cost) Test Certificates 3rd Party Witness Test (Additional Cost) ABS/CDS Type Approval Accessories such as SAFETY CLAMPS are available.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 86

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Black Gold

Oilfield Hose Cementing (Nitrile Tube) 10,000 psi W.P. – 15,000 Test – 22,500 Minimum Burst Nom. I.D. 2

Nom. O.D. 2.80

Min. Bend Radius (Inches) 48

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

COUPLINGS:

FITTINGS:

PACKAGING: BRANDING:

CERTIFICATION/ STANDARDS:

OPTIONAL:

Wt. per Ft. of hose (Lbs) 4.66

Crimped Cplg. Wts. (Lbs.) 1502 Hammer Union Assy. Female Male Sub/Seal Sub/Nut 7341-1569 7341-1571 (7.8 Lbs.) (17.7 Lbs.)

(Specification 4651ZA) Maximum length of hose (Feet) 200

Safety Clamp & Chain Part No. 7361-6550

Used as a flexible connection between the cementing pump manifold and cementing head for conveyance of cement slurries at high pressure. -4°F to +250°F (-20°C to +121°C) continuous service. Tube: Type C (Nitrile). Black. Specially compounded for handling abrasion and corrosion. Reinforcement: Multiple layers of spiraled high tensile steel wire. Cover: Type L (MegaTuff®). Black. Oil and abrasion resistant. Crimped – Gates GSH™ with integral 2” Fig. 1502 hammer union couplings with male sub/nut and female sub/seal. Couplings can be supplied with your choice of end fittings. Please contact your nearest Roughneck Distributor for more detailed information. (Refer to Roughneck Distributor list at the beginning of this section). NOTE: FIELD WELDING OF FITTINGS TO COUPLING IS NOT RECOMMENDED. GSH with Integral 2” Fig. 1502 Hammer Unions

Each length packaged in a carton. One continuous longitudinal yellow transfer label (with serial number and code date embossed). Example: “GATES® BLACK GOLD® CEMENTING NOT FOR SOUR SERVICE 2 INCH MAX WP 10000 PSI TESTED TO 15000 PSI FSL 0 TEMP RANGE III ISO 14693 LICENSE 7K-0003 MADE IN U.S.A.” API (American Petroleum Institute) Spec 7K. Coupling/Mat’l Traceability (Additional Cost) ISO 14693 Letter of Conformance (Additional Cost) Test Certificates 3rd Party Witness Test (Additional Cost) ABS/CDS Type Approval Accessories such as SAFETY CLAMPS are available.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 87

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Black Gold

Oilfield Hose Sour Service 5,000 psi W.P. – 10,000 Test – 12,500 Minimum Burst Nom. I.D.

Nom. O.D.

Min. Bend Radius (Inches)

Wt. per Ft. of hose (Lbs)

2-1/2

4.15

4.61

3-1/2 4

5.25 5.58

54 54

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

COUPLINGS:

(Specification 4774F) Swage Cplg. Wts. Each (Lbs) 33

Maximum length of hose (Feet)

Safety Clamp & Chain Part No.

10.1

Coupling Threads API (T) (In.) 3"

7361-0825

11.1

44.5

7361-0830

13.2 13.9

4" 5"

47 55

90 90

7361-0835 7361-0840

Flexible connection between standpipe and swivel (Rotary Drilling) or between pump and standpipe (Rotary Vibrator). -4°F to +200°F (-20°C to +93°C) continuous service. Tube:

Type V (Fluoroelastomer). Black. Resists abrasion, corrosion, oil, and up to 20% H 2S. NOTE: Hose is manufactured to handle up to 20% Hydrogen Sulfide (H 2S) for 1 hour at 93°C (200°F) at rated working pressure. Reinforcement: Multiple layers of "close wound", high tensile steel cables, with one layer of adhesion fabric placed between cable layers. Multiple layers of reinforcement under cover. Cover: Type C4 (Modified Nitrile). Black. Specially compounded UltraBrasion cover is resistant to abrasion, corrosion, cutting, gouging, oil and weather.

Swaged – meets NACE MR0175. API male line pipe threads standard. Gates recommends butt-welded couplings. Couplings can be supplied with your choice of end fittings. Please contact your nearest Roughneck Distributor for more detailed information. (Refer to Roughneck Distributor list at the beginning of this section). NOTE: FIELD WELDING OF FITTINGS TO COUPLING IS NOT RECOMMENDED.

FITTINGS:

PACKAGING: BRANDING:

CERTIFICATION/ STANDARDS:

OPTIONAL:

Each length packaged in a heavy-duty wooden crate. One continuous longitudinal yellow transfer label (with serial number and code date embossed). Example: “GATES® BLACK GOLD® SOUR SERVICE – MAX 20% H2S 4 INCH MAX WP 5000 PSI TESTED TO 10000 PSI MADE IN U.S.A.” Coupling/Mat’l Traceability (Additional Cost) Letter of Conformance (Additional Cost) NACE Test Certificates 3rd Party Witness Test (Additional Cost) Accessories such as SAFETY CLAMPS, HOSE LIFT EYE & COLLAR CLAMP and STAINLESS STEEL ARMOR are available.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 88

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Black Gold

Oilfield Hose Sour Service 7,500 psi W.P. – 15,000 Test – 18,750 Minimum Burst

(Specification 4773LE)

Nom. I.D. 2-1/2

Nom. O.D. 5.14

Min. Bend Radius (Inches) 48

Wt. per Ft. of hose (Lbs) 20.6

Swage Cplg. Wts. Each (Lbs) 62

Maximum length of hose (Feet) 90

Safety Clamp & Chain Part No. 7361-0835

5.64

23.0

7361-0840

3-1/2 4

6.05 6.40

54 60

24.6 26.4

75 90

90 90

7361-0845 7361-0850

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

COUPLINGS:

Flexible connection between standpipe and swivel (Rotary Drilling) or between pump and standpipe (Rotary Vibrator). -4°F to +200°F (-20°C to +93°C) continuous service. Tube:

Swaged – meets NACE MR0175. API 7K hose assemblies with working pressures exceeding 5,000 psi, the end fitting will be butt-welded onto the hose coupling. Couplings can be supplied with your choice of end fittings. Please contact your nearest Roughneck Distributor for more detailed information. (Refer to Roughneck Distributor list at the beginning of this section). NOTE: FIELD WELDING OF FITTINGS TO COUPLING IS NOT RECOMMENDED.

FITTINGS:

PACKAGING: BRANDING:

CERTIFICATION/ STANDARDS:

OPTIONAL:

Each length packaged in a heavy-duty wooden crate. One continuous longitudinal yellow transfer label (with serial number and code date embossed). Example: “GATES® BLACK GOLD® SOUR SERVICE – MAX 20% H2S 4 INCH MAX WP 7500 PSI TESTED TO 15000 PSI MADE IN U.S.A.” Coupling/Mat’l Traceability (Additional Cost) Letter of Conformance (Additional Cost) NACE Test Certificates 3rd Party Witness Test (Additional Cost) Accessories such as SAFETY CLAMPS, HOSE LIFT EYE & COLLAR CLAMP and STAINLESS STEEL ARMOR are available.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 89

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Black Gold

Oilfield Hose Choke and Kill 5,000 psi W.P. – 10,000 Test – 15,000 Minimum Burst Nom. I.D. 2-1/2*

Nom. O.D. 4.15

Min. Bend Radius (Inches) 36

Wt. per Ft. of hose (Lbs) 10.1

Swage Cplg. Wts. Each (Lbs) 33

(Specification 4774F*/4773LE**) Maximum length of hose (Feet) 90

Safety Clamp & Chain Part No. 7361-0825

4.61

11.1

44.5

7361-0830

3-1/2*

5.25

13.2

7361-0835

4**

6.40

26.4

7361-0850

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

COUPLINGS:

Flexible hose between the riser and manifold or around the ball joint of offshore drilling rigs. -4°F to +200°F (-20°C to +93°C) continuous service. Tube:

Type V (Fluoroelastomer). Black. Resists abrasion, corrosion, oil, and up to 20% H 2S. NOTE: Hose is manufactured to handle up to 20% Hydrogen Sulfide (H2S) for 1 hour at 93°C (200°F) at rated working pressure. Reinforcement: Multiple layers of "close wound", high tensile steel cables, with one layer of adhesion fabric placed between cable layers. Multiple layers of reinforcement under cover. Cover: Type C4 (Modified Nitrile). Black. Specially compounded UltraBrasion cover is resistant to abrasion, corrosion, cutting, gouging, oil and weather.

Swaged – meets NACE MR0175. Per API – flexible Choke and Kill hose end fittings will be butt-welded and the pressure rating shall be equivalent to the pressure rating of the flexible hose. Couplings can be supplied with your choice of end fittings. Please contact your nearest Roughneck Distributor for more detailed information. (Refer to Roughneck Distributor list at the beginning of this section). NOTE: FIELD WELDING OF FITTINGS TO COUPLING IS NOT RECOMMENDED.

FITTINGS:

PACKAGING: BRANDING:

CERTIFICATION/ STANDARDS:

OPTIONAL:

Each length packaged in a heavy-duty wooden crate. One continuous longitudinal yellow transfer label (with serial number and code date embossed). Example: “GATES® BLACK GOLD® CHOKE AND KILL – MAX 20% H2S 4 INCH MAX WP 5000 PSI TESTED TO 10000 PSI MADE IN U.S.A.” Coupling/Mat’l Traceability (Additional Cost) Letter of Conformance (Additional Cost) NACE Test Certificates 3rd Party Witness Test (Additional Cost) Accessories such as SAFETY CLAMPS, HOSE LIFT EYE & COLLAR CLAMP and STAINLESS STEEL ARMOR are available.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 90

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Black Gold

Oilfield Hose Choke and Kill 10,000 psi W.P. – 15,000 Test – 22,500 Minimum Burst

(Specification 4773LE)

Nom. I.D. 2-1/2

Nom. O.D. 5.14

Min. Bend Radius (Inches) 48

Wt. per Ft. of hose (Lbs) 20.6

Swage Cplg. Wts. Each (Lbs) 60

Maximum length of hose (Feet) 90

Safety Clamp & Chain Part No. 7361-0835

5.64

23.0

7361-0840

3-1/2

6.05

24.6

7361-0845

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

COUPLINGS:

Flexible hose between the riser and manifold or around the ball joint of offshore drilling rigs. -4°F to +200°F (-20°C to +93°C) continuous service. Tube:

Type V (Fluoroelastomer). Black. Resists abrasion, corrosion, oil, and up to 20% H 2S. NOTE: Hose is manufactured to handle up to 20% Hydrogen Sulfide (H 2S) for 1 hour at 93°C (200°F) at rated working pressure. Reinforcement: Multiple layers of "close wound", high tensile plated steel cables, with one layer of adhesion fabric placed between cable layers. Multiple layers of reinforcement under cover. Cover: Type C4 (Modified Nitrile). Black. Specially compounded UltraBrasion cover is resistant to abrasion, corrosion, cutting, gouging, oil and weather.

FITTINGS:

PACKAGING: BRANDING:

CERTIFICATION/ STANDARDS:

OPTIONAL:

Each length packaged in a heavy-duty wooden crate. One continuous longitudinal yellow transfer label (with serial number and code date embossed). Example: “GATES® BLACK GOLD® CHOKE AND KILL – MAX 20% H2S 3 INCH MAX WP 10000 PSI TESTED TO 15000 PSI MADE IN U.S.A.” Coupling/Mat’l Traceability (Additional Cost) Letter of Conformance (Additional Cost) Lloyds Fire Test OD/1000/499 NACE Test Certificates 3rd Party Witness Test (Additional Cost) Accessories such as SAFETY CLAMPS, HOSE LIFT EYE & COLLAR CLAMP and STAINLESS STEEL ARMOR are available.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 91

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Black Gold

Oilfield Hose Super Choke and Kill 15,000 psi W.P. – 22,500 Test – 33,750 Minimum Burst

(Specification 4758L)

Nom. I.D. 2-1/2

Nom. O.D. 5.66

Min. Bend Radius (Inches) 60

Wt. per Ft. of hose (Lbs) 29.4

Swage Cplg. Wts. Each (Lbs) 130

Maximum length of hose (Feet) 90

Safety Clamp & Chain Part No. 7361-0840

6.16

33.2

172

7361-0845

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

COUPLINGS:

Flexible hose between the riser and manifold or around the ball joint of offshore drilling rigs. -4°F to +200°F (-20°C to +93°C) continuous service. Tube:

Type V (Fluoroelastomer). Black. Resists abrasion, corrosion, oil, and up to 20% H 2S. NOTE: Hose is manufactured to handle up to 20% Hydrogen Sulfide (H 2S) for 1 hour at 93°C (200°F) at rated working pressure. Reinforcement: Multiple layers of "close wound", high tensile plated steel cables to withstand flexing and high pressures encountered in offshore operations. Multiple layers of fabric reinforcement under cover. Cover: Type C4 (Modified Nitrile). Black. Specially compounded UltraBrasion cover is resistant to abrasion, corrosion, cutting, gouging, oil and weather.

Special Built-In – meets NACE MR0175. Per API – flexible Choke and Kill hose end fittings will be buttwelded and the pressure rating shall be equivalent to the pressure rating of the flexible hose. Couplings can be supplied with your choice of end fittings. Please contact your nearest Roughneck Distributor for more detailed information. (Refer to Roughneck Distributor list at the beginning of this section). NOTE: FIELD WELDING OF FITTINGS TO COUPLING IS NOT RECOMMENDED.

FITTINGS:

PACKAGING: BRANDING:

CERTIFICATION/ STANDARDS:

OPTIONAL:

Each length packaged in a heavy-duty wooden crate. One continuous longitudinal yellow transfer label (with serial number and code date embossed). Example: “GATES® BLACK GOLD® SUPER CHOKE AND KILL – MAX 20% H2S 3 INCH MAX WP 15000 PSI TESTED TO 22500 PSI MADE IN U.S.A.” Coupling/Mat’l Traceability (Additional Cost) Letter of Conformance (Additional Cost) NACE Test Certificates 3rd Party Witness Test (Additional Cost) Accessories such as SAFETY CLAMPS, HOSE LIFT EYE & COLLAR CLAMP and STAINLESS STEEL ARMOR are available.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 92

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Black Gold

Oilfield Hose Rotary Decoking

5,000 psi W.P. – 10,000 Test – 12,500 Minimum Burst – Grade D (Specification 4774PE) Nom. I.D. 3

Nom. O.D. 4.61

Min. Bend Radius (Inches) 48

Wt. per Ft. of hose (Lbs) 10.8

Swage Cplg. Wts. Each (Lbs) 44.5

Maximum length of hose (Feet) 90

Safety Clamp & Chain Part No. 7361-0830

3-1/2

5.25

12.8

5.61

13.4

7361-0835

7361-0840

7,500 psi W.P. – 15,000 Test – 18,750 Minimum Burst – Grade E (Specification 4773PE) Nom. I.D. 3 3-1/2

Nom. O.D. 5.66 6.04

Min. Bend Radius (Inches) 48 54

Wt. per Ft. of hose (Lbs) 22.6 24.1

Swage Cplg. Wts. Each (Lbs) 70 75

Maximum length of hose (Feet) 90 90

Safety Clamp & Chain Part No. 7361-0840 7361-0845

6.40

25.8

7361-0850

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

COUPLINGS:

Coke is one of the by-products used in oil refining. It is stored in silos until it can be loaded into railroad cars for shipment. The coke hardens after being placed in the silos. To unload the coke from the silos, a decoking hose is attached to a drill stem which travels down the silo using warm, high-pressure water to wash the loosened coke from the silo.

-4°F to +180°F (-20°C to +82°C) continuous service. Tube:

Type C3 (Modified Nitrile). 3/16" thick. Black. Specially compounded for handling abrasion and corrosion. Reinforcement: Multiple layers of polyester cord over tube. Multiple layers of "close wound", high tensile steel cables with one layer of adhesion fabric placed between cable layers. Multiple layers of reinforcement under cover. Cover: Type C4 (Modified Nitrile). Black. Specially compounded UltraBrasion cover is resistant to abrasion, corrosion, cutting, gouging, oil and weather. Swaged – supplied with API standard flanges or equivalent of your choice. Please contact your nearest Roughneck Distributor for more detailed information. (Refer to Roughneck Distributor list at the beginning of this section).

NOTE: FIELD WELDING OF FITTINGS TO COUPLING IS NOT RECOMMENDED. FITTINGS:

PACKAGING: BRANDING: CERTIFICATION/ STANDARDS:

OPTIONAL:

Coupling/Mat’l Traceability (Additional Cost) Letter of Conformance (Additional Cost) Test Certificates 3rd Party Witness Test (Additional Cost) Accessories such as SAFETY CLAMPS, HOSE LIFT EYE & COLLAR CLAMP and STAINLESS STEEL ARMOR are available.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 93

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Safety Clamps & Chain

Oilfield Hose

For Rotary Vibrator/Drilling Hose Grade “D” Rotary Hose or Motion Compensator Hose 5,000 psi W.P. – 10,000 Test Nom. I.D. (In.)

2-1/2 3 3-1/2 4

(mm)

Standard Pack

Stock (X) or Minimum Order Qty.

Gates Item. No.

63.5 76.2 88.9 101.6

1 EA 1 EA 1 EA 1 EA

X X X X

7361-0825 7361-0830 7361-0835 7361-0840

Stock (X) or Minimum Order Qty.

Gates Item. No.

X X X X

7361-0835 7361-0840 7361-0845 7361-0850

Grade “E” Rotary Hose 7,500 psi W.P. – 15,000 Test Nom. I.D. (In.)

(mm)

Standard Pack

2-1/2 3 3-1/2 4

63.5 76.2 88.9 101.6

1 EA 1 EA 1 EA 1 EA

SAFETY CLAMP: NOTE:

LIFT EYE AND COLLAR: NOTE:

STAINELSS STEEL ARMOR: NOTE:

A set of safety clamps can be obtained on special order. Location for attaching these safety clamps is shown by notations marked at each end of the assembly. Not Sold Separately. Additional Cost. Contact a Roughneck Distributor for pricing.

Hose lift eye and collar clamp also available. Do not use safety clamp and chain for lifting. Additional Cost. Contact a Roughneck Distributor for pricing.

An external stainless steel armor shield can be supplied. Applied over the hose cover. The armor provides extra abrasion and mechanical protection for the hose, where external abuse is severe. Additional Cost. Contact a Roughneck Distributor for pricing.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 94

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Powerbraid® Plus (Slim Hole Rotary)

Oilfield Hose

(Specification 3670H, 4651RL, ZL) 2,000 - 3,000 Working Pressure 4651RL, 3670H Nom. I.D. (In.) 2 2 2 1/2 3

(mm) 50.8 50.8 63.5 76.2

Nom. O.D. (In.) 2.63 2.63 3.38 3.90

(mm) 66.8 66.8 85.9 99.1

Max. W.P. (psi) 3000 3000 2500 2000

(MPa) 20.68 20.68 17.24 13.79

Suction (In. Hg) — — — —

(mm Hg) — — — —

Min. Bend Radius (In.) 25.0 25.0 30.0 36.0

(mm Hg) — — — — —

Min. Bend Radius (In.) 12.0 16.5 20.0 25.0 25.0

(mm) 635 635 762 914

Wt. Per Ft. (Lbs.) 2.95 2.95 4.00 4.33

(mm) 305 419 508 635 635

Wt. Per Ft. (Lbs.) 1.49 2.67 3.22 4.72 4.72

(Kg) 1.34 1.34 1.81 1.96

Standard Pack 50 ft. 200 ft. 50 ft. 50 ft.

Stock (X) or Minimum Order Qty. X X X X

Gates Item No. 3670-0655 3670-0660 3670-0656 3670-0657

(Kg) .68 1.21 1.46 2.14 2.14

Standard Pack 200 ft. 200 ft. 200 ft. 50 ft. 200 ft.

Stock (X) or Minimum Order Qty. X X X X X

Gates Item No. 3670-0665 3670-0670 3670-0675 3670-0679 3670-0680

5,000 Working Pressure 4651ZL Nom. I.D. (In.) 1 1 1/4 1 1/2 2 2

(mm) 25.4 31.8 38.1 50.8 50.8

Nom. O.D. (In.) 1.53 1.97 2.26 2.80 2.80

(mm) 38.9 50.0 57.4 71.1 71.1

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 5000 5000 5000 5000 5000

(MPa) 34.47 34.47 34.47 34.47 34.47

Suction (In. Hg) — — — — —

Rotary applications on workover rigs and slim hole or seismograph rigs designed to operate at a maximum of 2,000 to 5,000 PSI rated working pressure depending on size. Applications on small or medium-size drilling rigs used for water well operations, water well core drill, blast or shot hole operations. Hoses are flexible connectors in pressure lines used in conveying mud or air. For normal air or mud applications and where increased resistance to external abuse or pump pulsations is required. -40°F to +180°F (-40°C to +82°C) continuous service. Tube: Reinforcement: Cover:

Type A (Neoprene). Black. For 1 1/2" I.D. and 2" I.D. 5,000 psi and 2" I.D. 3,000 psi. Type C (Nitrile). Black. For 1' and 1 1/4" I.D. 5,000 psi, 2 1/2" I.D. 2,500 psi and 3" I.D. 2,000 psi. High tensile steel wire. (Minimum 2.5:1 design factor). Type A (Neoprene). Black with blue longitudinal stripes. All sizes perforated.

COUPLINGS:

1 1/2" I.D. 5,000 psi. Gates 24PCM-24MPAPI (7347-0307) 1 1/4" I.D. 5,000 psi. Gates 20GS-20MPAPI (7347-7695) 1" I.D. 5,000 psi. Gates 16GS-16MPLH (7347-7654) 2" I.D. 5,000 psi. Gates 32PCM-32MPAPI (7347-0305) 2" I.D. 5,000 psi. Gates 32PCS-32MPAPI (7347-0389) 71 Permanent (Mulconroy - API threads only) or reusable male couplings (Wildman - API threads only). 77 GSH® with Integral 2" Fig. 1502 Hammer Unions. Reference the Hose Coupling Section. For GS, PCM and PCS couplings reference Gates Hydraulic Hose catalog #35093.

PACKAGING:

All sizes packaged 1 length in a carton.

BRANDING:

Continuous transfer label. Example: “GATES® POWERBRAID® PLUS SLIM HOLE ROTARY 2 INCH 3000 PSI WP FLAME RESISTANT, MSHA 2G-IC-11C MADE IN U.S.A.”

SPECIAL ORDER REQUIREMENTS:

Special production runs require minimum order quantities of 3,000 feet for 1" and 1,800 feet for 1 1/4" through 2". For 2", 2 1/2" and 3" 50 foot lengths, minimum is 600 feet. Maximum length available for 2 1/2" and 3" is 50 ft.

REMNANT LENGTHS: STANDARDS:

None. Tube: Cover:

RMA (Class B) Medium oil resistance. Meets MSHA 30 CFR 18.65. Flame resistant.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 95

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

16 EFBOP Blow-Out Preventer

Oilfield Hose

(Specification 4651ZL, XL) Nom. I.D. (In.) 1 1

(mm) 25.4 25.4

Nom. O.D. (In.) 1.53 1.53

(mm) 38.9 38.9

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 5000 6000

(MPa) 34.97 41.36

Suction (In. Hg) — —

(mm Hg) — —

Min. Bend Radius (In.) 12.0 12.0

(mm) 305 305

Wt. Per Ft. (Lbs.) 1.49 1.49

(Kg) .68 .68

Standard Pack 200 ft. 200 ft.

Stock (X) or Minimum Order Qty. X X

Gates Item No. 3670-0141 3670-0140

Insert hose in all oilfield blow-out systems. This rugged hose has been tested for 5,000 psi STATIC pressure requirements. NOTE: Insert must be sleeved and shielded for BOP applications in accordance with applicable specifications. -40°F to +250°F (-40°C to +121°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Petroleum and Bio-degradable oil resistant. High tensile steel wire. (Minimum 4:1 design factor for static applications). Type A (Neoprene). Black. Red lettering.

COUPLINGS:

Gates GlobalSpiral. Stem 16GS-16MPAPI (7347-79285), 16GS-16MPLH (7347-76545). Ferrule 16GS1F-4 (734703145). See the Gates Hydraulics catalog 35093.

PACKAGING:

200' per carton.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous transfer label. Example: “GATES® ENVIROFLUID™ 16 EFBOP 5000 PSI MAX STATIC WP USE ONLY FOR BLOW OUT PREVENTER INSERT HOSE MADE IN U.S.A.” Special production runs require minimum order quantities of 3000 feet. If a special transfer label is required, contact Gates Corporation for minimum quantity. None. Tube: Cover:

RMA (Class A) High oil resistance. Meets MSHA 30 CFR 18.65. Flame resistant.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 96

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Longhorn®

Petroleum Transfer Hose

(Specification 4688CC/4688DC) Smooth Cover (4688CC) Nom. I.D. (In.) 1 1 1 1/4 1 1/2 1 1/2 2 2 2 1/2 2 1/2 3 3 4 4

(mm) 25.4 25.4 31.8 38.1 38.1 50.8 50.8 63.5 63.5 76.2 76.2 101.6 101.6

Nom. O.D. (In.) 1.50 1.50 1.75 2.02 2.02 2.52 2.52 3.05 3.05 3.58 3.58 4.62 4.62

(mm) 38.1 38.1 44.5 51.3 51.3 64.0 64.0 77.5 77.5 90.9 90.9 117.4 117.4

Max. W.P. (psi) 150 150 150 150 150 150 150 150 150 150 150 150 150

(MPa) 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(MPa) 1.03 1.03 1.03 1.03

Suction (In. Hg) 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 3.0 3.0 4.0 4.0 4.0 6.0 6.0 8.0 8.0 9.0 9.0 12.0 12.0

(mm Hg) 762 762 762 762

Min. Bend Radius (In.) 5.0 8.0 11.0 17.0

(mm) 76 76 102 102 102 152 152 203 203 229 229 305 305

Wt. Per Ft. (Lbs.) .60 .60 .72 .88 .88 1.12 1.12 1.50 1.50 1.90 1.90 2.65 2.65

(mm) 127 203 279 432

Wt. Per Ft. (Lbs.) 1.13 1.78 2.65 5.91

(Kg) .27 .27 .33 .36 .36 .51 .51 .68 .68 .86 .86 1.20 1.20

Standard Pack 200 ft. 100 ft. 100 ft. 100 ft. 200 ft. 100 ft. 200 ft. 200 ft. 100 ft. 100 ft. 200 ft. 100 ft. 200 ft.

Stock (X) or Minimum Order Qty. 400 ft. X X X 400 ft. X 400 ft. 400 ft. X X 400 ft. X 400 ft.

Gates Item No. 4688-0454 4688-1305 4688-1306 4688-1307 4688-1493 4688-1308 4688-1342 4688-0455 4688-1309 4688-1310 4688-1343 4688-1311 4688-1344

(Kg) .51 .81 1.20 2.68

Standard Pack 100 ft. 100 ft. 100 ft. 50 ft.

Stock (X) or Minimum Order Qty. X X X X

Gates Item No. 4688-1351 4688-1352 4688-1353 4688-1355

Corrugated Cover (4688DC) Nom. I.D. (In.) 2 3 4 6

(mm) 50.8 76.2 101.6 152.4

Nom. O.D. (In.) 2.52 3.58 4.64 6.87

(mm) 64.0 90.9 117.9 174.5

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 150 150

Transfer of refined fuels (commercial gasoline and diesel fuel), oils and other petroleum products. Ideal for oilfield service truck use. Service life of transfer hoses can be extended by draining hoses after use. For bio-diesel and other alternative fuel applications, see Longhorn® AF. Petroleum transfer hoses may be used with all grades of bio-diesel only if the exposure is intermittent and the hose is drained between uses. -40°F to +180°F (-40°C to +82°C). Warning: Do not convey fuels over 120°F (+49°C). Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Synthetic, high tensile textile with steel wire helix. Type A (Neoprene). Black with red spiral stripe.

COUPLINGS:

7, 26, 49 or 78. (for ambient temperatures only). Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled and wrapped in polyethylene.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous transfer label. Example: “GATES® Longhorn® Petroleum Transfer 150 PSI (1.03MPa) WP Made In U.S.A.” Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube:

RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 97

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Longhorn® AF (Alternative Fuel-Corrugated)

Petroleum Transfer Hose

(Specification 4688AC, AF) Smooth Cover (4688AF) Nom. I.D. (In.) 1 1 1 1/4 1 1/4 1 1/2 1 1/2 2 2 2 1/2 2 1/2 3 3 4 4

(mm) 25.4 25.4 31.8 31.8 38.1 38.1 50.8 50.8 63.5 63.5 76.2 76.2 101.6 101.6

Nom. O.D. (In.) 1.50 1.50 1.75 1.75 2.02 2.02 2.52 2.52 3.05 3.05 3.53 3.53 4.57 4.57

(mm) 38.1 38.1 44.5 44.5 51.3 51.3 64.0 64.0 77.5 77.5 89.7 89.7 116.1 116.1

Max. W.P. (psi) 150 150 150 150 150 150 150 150 150 150 150 150 150 150

(MPa) 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(MPa) 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 3.0 3.0 4.0 4.0 4.0 4.0 6.0 6.0 8.0 8.0 9.0 9.0 12.0 12.0

(mm Hg) 762 762 762 762 762 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 3.0 4.0 4.0 4.0 4.0 6.0 6.0 8.0 8.0 9.0 9.0 12.0 12.0

(mm) 76 76 102 102 102 102 152 152 203 203 229 229 305 305

Wt. Per Ft. (Lbs.) .53 .59 .70 .70 .87 .87 1.10 1.10 1.47 1.47 1.86 1.86 2.59 2.59

(mm) 76 102 102 102 102 152 152 203 203 229 229 305 305

Wt. Per Ft. (Lbs.) .59 .70 .70 .87 .87 1.10 1.10 1.47 1.47 1.86 1.86 2.59 2.59

(Kg) .27 .27 .32 .32 .39 .39 .50 .50 .67 .67 .84 .84 1.17 1.17

Standard Pack 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft.

Stock (X) or Minimum Order Qty. X 400 ft. X 400 ft. X 400 ft. X 400 ft. X 400 ft. X 400 ft. X 400 ft.

Gates Item No. 4688-1700 4688-1701 4688-1702 4688-1703 4688-1704 4688-1705 4688-1706 4688-1707 4688-1708 4688-1709 4688-1710 4688-1711 4688-1712 4688-1713

(Kg) .27 .32 .32 .39 .39 .50 .50 .67 .67 .84 .84 1.17 1.17

Standard Pack 100 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft.

Stock (X) or Minimum Order Qty. X X 400 ft. X 400 ft. X 400 ft. X 400 ft. X 400 ft. X 400 ft.

Gates Item No. 4688-1718 4688-1720 4688-1721 4688-1722 4688-1723 4688-1724 4688-1725 4688-1726 4688-1727 4688-1728 4688-1729 4688-1730 4688-1731

Corrugated Cover (4688AC) Nom. I.D. (In.) 1 1 1/4 1 1/4 1 1/2 1 1/2 2 2 2 1/2 2 1/2 3 3 4 4

(mm) 25.4 31.8 31.8 38.1 38.1 50.8 50.8 63.5 63.5 76.2 76.2 101.6 101.6

Nom. O.D. (In.) 1.50 1.75 1.75 2.02 2.02 2.52 2.52 3.05 3.05 3.53 3.53 4.57 4.57

(mm) 38.1 44.5 44.5 51.3 51.3 64 64 77.5 77.5 89.7 89.7 116.1 116.1

Max. W.P. (psi) 150 150 150 150 150 150 150 150 150 150 150 150 150

RECOMMENDED FOR:

Longhorn AF is designed and engineered specifically for constant contact use in the transfer of alternative fuels such as bio-diesel, bio-diesel blends, ethanol and ethanol blends. It can also be used for transfer of commercial gasolines, diesel fuels, oils and other petroleum products. It is ideal for tank truck, terminal loading and in-plant operations.

TEMPERATURE:

-30°F to +180°F (-34°C to +82°C). Warning: Do not convey fuels over 120°F (+49°C). Contact Denver Product Application (303) 744-5070 for use at temperature extremes.

CONSTRUCTION:

Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Synthetic, high tensile textile with steel wire helix. Type C2 (Modified Nitrile). Black with red spiral stripe and green boarder.

COUPLINGS:

7, 26, 49 or 78. (for ambient temperatures only). Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled and wrapped in polyethylene.

BRANDING:

Continuous transfer label. Example: “GATES® LONGHORN® AF 150 PSI (1.03MPa) WP FLAME RESISTANT MSHA IC-4116 MADE IN U.S.A.”

SPECIAL ORDER REQUIREMENTS:

REMNANT LENGTHS: STANDARDS:

Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube: Cover:

RMA (Class A) High oil resistance. Meets MSHA 30 CFR 18.65. Flame resistant. RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 98

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Steer®

Petroleum Transfer Hose

(Specification 4688CN) Nom. I.D. (In.) 2 2 3 3 4 4

(mm) 50.8 50.8 76.2 76.2 101.6 101.6

Nom. O.D. (In.) 2.44 2.44 3.45 3.45 4.51 4.51

(mm) 62.0 62.0 87.6 87.6 114.6 114.6

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 150 150 150 150

(MPa) 1.03 1.03 1.03 1.03 1.03 1.03

Suction (In. Hg) — — — — — —

(mm Hg) — — — — — —

Min. Bend Radius (In.) — — — — — —

(mm) — — — — — —

Wt. Per Ft. (Lbs.) .93 .93 1.39 1.39 2.03 2.03

(Kg) .42 .42 .63 .63 .92 .92

Standard Pack 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft.

-40°F to +180°F (-40°C to +82°C). Warning: Do not convey fuels over 120°F (+49°C). Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Braided, high tensile synthetic textile cord with static conductor. Type A (Neoprene). Black with red spiral stripe.

7, 26, 49 or 78. (for ambient temperatures only). Reference the Hose Coupling Section.

PACKAGING:

100' length coiled and wrapped in polyethylene.

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Gates Item No. 4688-1320 4688-1491 4688-1321 4688-1530 4688-1322 4688-1531

COUPLINGS:

BRANDING:

Stock (X) or Minimum Order Qty. X 400 ft. X 400 ft. X 400 ft.

Continuous transfer label. Example: “GATES® Steer® Petroleum Transfer Discharge 150 PSI (1.03MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube:

RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 99

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Maverick™

Petroleum Transfer Hose

(Specification 4687R) Nom. I.D. (In.) 2 3 4

(mm) 50.8 76.2 101.6

Nom. O.D. (In.) 2.48 3.50 4.50

(mm) 63.0 88.9 114.3

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 100 100 100

(MPa) .69 .69 .69

Suction (In. Hg) 30.0 30.0 30.0

(mm Hg) 762 762 762

Min. Bend Radius (In.) 4.0 6.0 11.0

(mm) 102 152 279

Wt. Per Ft. (Lbs.) 1.08 1.73 2.25

(Kg) .49 .79 1.02

Standard Pack 100 ft. 100 ft. 100 ft.

-40°F to +180°F (-40°C to +82°C). Warning: Do not convey fuels over 120°F (+49°C). Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Synthetic, high tensile textile with steel wire helix. Type C2 (Modified Nitrile). Red corrugated with white spiral stripe.

COUPLINGS:

7, 26, 49 or 78. (for ambient temperatures only). Reference the Hose Coupling Section. 100' length coiled and wrapped in polyethylene.

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Gates Item No. 4687-0251 4687-0252 4687-0253

PACKAGING: BRANDING:

Stock (X) or Minimum Order Qty. X X X

Continuous transfer label. Example: “GATES® Maverick™ Petroleum Transfer 100 PSI (.69MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube:

RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 100

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Super-Vac®

Petroleum Transfer Hose

(Specification 4688V) Nom. I.D. (In.) 1 1 1/4 1 1/2 2 2 2 1/2 3 4 6 6 6

(mm) 25.4 31.8 38.1 50.8 50.8 63.5 76.2 101.6 152.4 152.4 152.4

Nom. O.D. (In.) 1.42 1.68 1.97 2.47 2.47 2.99 3.52 4.52 6.67 6.67 6.67

(mm) 36.1 42.7 50.0 62.7 62.7 75.9 89.4 114.8 169.4 169.4 169.4

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 150 150 150 150 150 100 60 60 60

(MPa) 1.03 1.03 1.03 1.03 1.03 1.03 1.03 .69 .41 .41 .41

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 3.0 3.0 3.0 4.0 4.0 5.0 6.0 8.0 18.0 18.0 18.0

(mm) 76 76 76 102 102 127 152 203 457 457 457

Wt. Per Ft. (Lbs.) .52 .67 .77 .99 .99 1.46 1.76 2.29 4.37 4.37 4.37

(Kg) .24 .30 .35 .45 .45 .66 .80 1.04 1.98 1.98 1.98

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 200 ft. 100 ft. 100 ft. 100 ft. 20 ft. 50 ft. 200 ft.

-40°F to +150°F (-40°C to +66°C) continuous service. NOTE: Diesel fuel normally conveyed below 120°F (+49°C). Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Synthetic, high tensile textile with steel wire helix. Type D (SBR). Black corrugated with blue spiral stripe.

COUPLINGS:

6, 7 or 78. (for ambient temperatures only). Reference the Hose Coupling Section. All lengths coiled and wrapped in polyethylene.

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Gates Item No. 4688-0651 4688-0653 4688-0656 4688-0665 4688-0668 4688-0675 4688-0680 4688-0690 4688-0697 4688-0698 4688-0702

NOTE: NOT RECOMMENDED FOR REFINED PETROLEUM PRODUCTS SUCH AS GASOLINE. Tank truck service, including oil field vacuum truck, where full suction or rated working pressures are required. Ideal for applications handling crude oil, salt and fresh water, tank bottoms, drilling mud, dilute solutions of hydrochloric acids, diesel fuels and sewage transfer. Reference Gates Chemical Resistance Table.

PACKAGING: BRANDING:

Stock (X) or Minimum Order Qty. X X X X 400 ft. X X X X X 400 ft.

Continuous transfer label. Example: “GATES® Super-Vac® Oil Field Vacuum 150 PSI (1.03MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet for sizes through 4" and 200 feet for sizes above 4". If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube:

RMA (Class B) Medium oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 101

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Blender Transfer

Petroleum Transfer Hose

(Specification 4110DW) Nom. I.D. (In.) 4 5

(mm) 101.6 127.0

Nom. O.D. (In.) 4.73 5.73

(mm) 120.1 145.5

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

PACKAGING: BRANDING: SPECIAL ORDER REQUIREMENTS:

Max. W.P. (psi) 150 150

(MPa) 1.03 1.03

Suction (In. Hg) — —

(mm Hg) — —

Min. Bend Radius (In.) — —

(mm) — —

Wt. Per Ft. (Lbs.) 3.07 3.77

(Kg) 1.39 1.71

Standard Pack 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. 400 ft. 400 ft.

Gates Item No. 4110-0400 4110-0500

Transfer of water, petroleum based fluids, dilute acids, chemicals and abrasive slurries used in oil and gas well stimulation. -40°F to +180°F (-40°C to +82°C). Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Synthetic, high tensile textile. Type A (Neoprene). Black with red spiral stripe.

100' length coiled and wrapped in polyethylene. Continuous transfer label. Example: “GATES® Blender Transfer 150 PSI (1.03MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet for 4" and 200 feet for 5". If a special transfer label is required, contact Denver Industrial Hose Marketing for minimum quantity.

REMNANT LENGTHS:

None.

STANDARDS:

Tube:

RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 102

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Sea Horse® 400 (Fuel Transfer)

Petroleum Transfer Hose

(Specification 4110SH) Nom. I.D. (In.) 2 3 4

(mm) 50.8 76.2 101.6

Nom. O.D. (In.) 2.70 3.67 4.83

(mm) 68.6 93.2 122.7

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 400 400 400

(MPa) 2.76 2.76 2.76

Suction (In. Hg) 10.0 10.0 10.0

(mm Hg) 254 254 254

Min. Bend Radius (In.) 17.0 22.0 30.0

200' length coiled and wrapped in polyethylene.

STANDARDS:

Gates Item No. 4110-0715 4110-0716 4110-0717

Type C (Nitrile). Black. Synthetic, high tensile textile with static wire. Type A (Neoprene). Black with red spiral stripe.

14, 15, 71. Reference the Hose Coupling Section.

REMNANT LENGTHS:

Stock (X) or Minimum Order Qty. X X X

-40°F to +180°F (-40°C to +82°C) continuous service. Tube: Reinforcement: Cover:

COUPLINGS:

SPECIAL ORDER REQUIREMENTS:

(Kg) .68 .97 1.56

Standard Pack 200 ft. 200 ft. 200 ft.

Transfer of refined fuels (commercial gasoline, diesel fuel) oils and other petroleum products. Transfer hoses are designed for intermittent contact with refined fuels and must be drained after use. Ideal for offshore/onshore transfer applications involving discharge service for diesel oils and other similar petroleum products where an extremely lightweight, flexible hose with a high rated working pressure and a small minimum bend radius is required. For bio-diesel and other alternative fuel applications, see Longhorn® AF. Petroleum transfer hoses may be used with all grades of bio-diesel only if the exposure is intermittent and the hose is drained between uses.

PACKAGING: BRANDING:

(mm) 432 559 762

Wt. Per Ft. (Lbs.) 1.51 2.14 3.43

Continuous transfer label. Example: “GATES® SEA HORSE® 400 Fuel Transfer 400 PSI (2.76MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube:

RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 103

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Sea Horse® 400 HW (Fuel Transfer Suction/Discharge Hardwall)

Petroleum Transfer Hose

(Specification 4688SH) Nom. I.D. (In.) 2 3 4

(mm) 50.8 76.2 101.6

Nom. O.D. (In.) 2.84 4.00 4.99

(mm) 72.1 101.6 126.8

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 400 400 400

(MPa) 2.76 2.76 2.76

Suction (In. Hg) 30.0 30.0 30.0

(mm Hg) 762 762 762

Min. Bend Radius (In.) 15.0 20.0 25.0

Tube: Reinforcement: Cover:

200' length coiled and wrapped in polyethylene.

STANDARDS:

Gates Item No. 4688-0590 4688-0591 4688-0592

Type C (Nitrile). Black. Synthetic, high tensile textile with steel wire helix. Type A (Neoprene). Black with red spiral stripe.

14, 15, 71. Reference the Hose Coupling Section.

REMNANT LENGTHS:

Stock (X) or Minimum Order Qty. X X X

-40°F to +180°F (-40°C to +82°C) continuous service.

COUPLINGS:

SPECIAL ORDER REQUIREMENTS:

(Kg) .92 1.66 2.11

Standard Pack 200 ft. 200 ft. 200 ft.

Transfer of refined fuels (commercial gasoline and diesel fuel) oils and other petroleum products. Transfer hoses are designed for intermittent contact with refined fuels and must be drained after use. Ideal for offshore/onshore transfer applications involving suction and discharge service for diesel oils and other similar petroleum products where an extremely lightweight, hardwall, flexible hose with a high rated working pressure and a small minimum bend radius is required. For bio-diesel and other alternative fuel applications, see Longhorn® AF. Petroleum transfer hoses may be used with all grades of bio-diesel only if the exposure is intermittent and the hose is drained between uses.

PACKAGING: BRANDING:

(mm) 381 508 635

Wt. Per Ft. (Lbs.) 2.03 3.66 4.64

Continuous transfer label. Example: “GATES® SEA HORSE® 400 HW Hardwall Fuel Transfer 400 PSI (2.76 MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube:

RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 104

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Sea Horse® (Fuel Transfer)

Petroleum Transfer Hose

(Specification 4110SS) Nom. I.D. (In.) 2 2 1/2 3 4 5

(mm) 50.8 63.5 76.2 101.6 127.0

Nom. O.D. (In.) 2.66 3.16 3.70 4.70 5.84

(mm) 67.6 80.3 94.0 119.4 148.3

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 300 300 300 300 300

(MPa) 2.07 2.07 2.07 2.07 2.07

Suction (In. Hg) 10.0 10.0 10.0 10.0 10.0

(mm Hg) 254 254 254 254 254

Min. Bend Radius (In.) 14.0 17.0 21.0 28.0 35.0

(mm) 356 432 533 711 889

Wt. Per Ft. (Lbs.) 1.40 1.70 2.17 2.80 4.14

(Kg) .64 .77 .98 1.27 1.88

Standard Pack 200 ft. 200 ft. 200 ft. 200 ft. 200 ft.

-40°F to +180°F (-40°C to +82°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Synthetic, high tensile textile with static wire. Type A (Neoprene). Black with red spiral stripe.

14, 15, 71, all sizes. 26 2" and 2 1/2" only. Reference the Hose Coupling Section.

PACKAGING:

200' length coiled and wrapped in polyethylene.

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Gates Item No. 4110-0701 4110-0704 4110-0707 4110-0710 4110-0713

COUPLINGS:

BRANDING:

Stock (X) or Minimum Order Qty. X 400 ft. X X X

Continuous transfer label. Example: “GATES® SEA HORSE® Fuel Transfer 300 PSI (2.07MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet for sizes through 4" and 200 feet for sizes above 4". If a special transfer label is required, contact Gates Corporation for minimum quantity. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube:

RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 105

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Sea Horse® HW (Fuel Transfer Suction/Discharge - Hardwall)

Petroleum Transfer Hose

(Specification 4688SS) Nom. I.D. (In.) 2 3 4 6

(mm) 50.8 76.2 101.6 152.4

Nom. O.D. (In.) 2.78 3.86 4.87 7.07

(mm) 70.6 98.0 123.7 179.6

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 300 300 300 200

(MPa) 2.07 2.07 2.07 1.38

Suction (In. Hg) 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762

Min. Bend Radius (In.) 10.0 18.0 24.0 36.0

Tube: Reinforcement: Cover:

200' length coiled and wrapped in polyethylene.

STANDARDS:

Stock (X) or Minimum Order Qty. X X X X

Gates Item No. 4688-0584 4688-0585 4688-0587 4688-0589

Type C (Nitrile). Black. Synthetic, high tensile textile with steel wire helix. Type A (Neoprene). Black with red spiral stripe.

PACKAGING:

REMNANT LENGTHS:

Standard Pack 200 ft. 200 ft. 200 ft. 100 ft.

-40°F to +180°F (-40°C to +82°C) continuous service.

14, 15 or 71. Reference the Hose Coupling Section.

SPECIAL ORDER REQUIREMENTS:

(Kg) .85 1.42 1.83 3.61

COUPLINGS:

BRANDING:

(mm) 254 457 610 914

Wt. Per Ft. (Lbs.) 1.87 3.14 4.03 7.95

Continuous transfer label. Example: “GATES® SEA HORSE® HW Hardwall Fuel Transfer 300 PSI (2.07MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet for sizes through 4" and 200 feet for sizes above 4". If a special transfer label is required, contact Gates Corporation for minimum quantity. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube:

RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 106

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Trident® 400

Petroleum Transfer Hose

(Specification 3150B) Nom. I.D. (In.) 2 2 1/2 3 4

(mm) 50.8 63.5 76.2 101.6

Nom. O.D. (In.) 2.71 3.20 3.71 4.84

(mm) 68.8 81.3 94.2 122.9

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 400 400 400 400

(MPa) 2.76 2.76 2.76 2.76

Suction (In. Hg) 10.0 10.0 10.0 10.0

(mm Hg) 254 254 254 254

Min. Bend Radius (In.) 16.0 20.0 24.0 32.0

(mm) 406 508 610 813

200' length coiled and wrapped in polyethylene.

STANDARDS:

Gates Item No. 3150-0410 3150-0411 3150-0412 3150-0413

Type A (Neoprene). Black. Synthetic, high tensile textile. Type A (Neoprene). Black with blue spiral stripe for high visibility.

14, 15, 71 or 8. Reference the Hose Coupling Section.

REMNANT LENGTHS:

Stock (X) or Minimum Order Qty. X 400 ft. X X

-30°F to +158°F (-34°C to +70°C) continuous service. Tube: Reinforcement: Cover:

COUPLINGS:

SPECIAL ORDER REQUIREMENTS:

(Kg) .68 .83 1.01 1.58

Standard Pack 200 ft. 200 ft. 200 ft. 200 ft.

NOTE: For fuels, use a petroleum transfer hose with a Type C (Nitrile) tube. Water, air and petroleum product transfer applications where a lightweight, flexible hose in long lengths is required.

PACKAGING: BRANDING:

Wt. Per Ft. (Lbs.) 1.50 1.82 2.23 3.49

Continuous transfer label. Example: “GATES® Trident® 400 Multi Service Transfer Air-Water-Petroleum 400 PSI WP Fluid/250 PSI WP Air Made In U.S.A.” Special production runs require minimum order quantities of 400 feet per size. If a special transfer label is required, contact Gates Corporation for minimum quantity. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. Tube:

RMA (Class B) Medium oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 107

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Master-Flex® Fuel Delivery

Petroleum Transfer Hose

(Specification 7744) Nom. I.D. (In.) (mm) 3 76.2 4 101.6 *Working Pressure

Nom. Max. O.D. W.P. (In.) (mm) (psi) (MPa) 3.76 95.5 65 .45 4.79 121.7 65 .45 and Suction at +72°F (+22°C).

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Suction (In. Hg) 28.0 28.0

(mm Hg) 711 711

Min. Bend Radius (In.) 6.0 8.0

(mm) 152 203

Stock (X) or Minimum Order Qty. X X

Gates Item No. 7744-7103 7744-7104

-30°F to +130°F (-34°C to +55°C) Warning: Do not convey fuels over 120°F (+49°C). Tube: Reinforcement: Cover:

Type C3 (Modified Nitrile). Black. Polyester fabric with static wire. Type G (PVC). Black with yellow helix.

COUPLINGS:

6, 7, 49 or 78. Reference the Hose Coupling Section. All lengths coiled and wrapped in polyethylene.

BRANDING:

(Kg) .78 1.11

Standard Pack 100 ft. 100 ft.

Transfer of commercial gasolines, diesel fuel, oils and other petroleum products. Ideal for oilfield service truck use.

PACKAGING:

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Wt. Per Ft. (Lbs.) 1.71 2.44

Unlabeled. None. None.

Master-Flex® Fuel Delivery Sleeve Nom. I.D. (In.) 3 4

(mm) 76.2 101.6

INSTALLATION:

RECOMMENDED FOR:

Wt. Per Ea. (Lbs.) 5.13 7.32

(Kg) 2.33 3.32

Standard Pack 3 ft. 3 ft.

Stock (X) or Minimum Order Qty. 1 ea. 1 ea.

Gates Item No. 7744-8103 7744-8104

Apply the sleeve by twisting in a clockwise direction. Use of an appropriate lubricant, i.e. soapy water solution, will simplify sleeve application and reduce possibility of damage to hose cover. Make sure sleeve is applied prior to coupling insertion. Soft Black PVC sleeve is designed to fit Gates Fuel Delivery Hose and provides a smooth banding surface.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 108

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Master-Flex® Vapor Recovery

Petroleum Transfer Hose

(Specification 7744) Nom. I.D. (In.) 1 1/2 2 3 4 5 6

(mm) 38.1 50.8 76.2 101.6 127.0 152.4

Nom. O.D. (In.) 1.88 2.43 3.54 4.56 5.51 6.52

(mm) 47.8 61.7 89.9 115.8 140.0 165.6

Max. W.P. (psi) 5 5 5 5 5 5

(MPa) .03 .03 .03 .03 .03 .03

Suction (In. Hg) — — — — — —

(mm Hg) — — — — — —

Min. Bend Radius (In.) 1.5 2.0 3.0 4.0 5.0 6.0

(mm) 38 51 76 102 127 152

Wt. Per Ft. (Lbs.) .36 .48 .69 .92 1.13 1.24

(Kg) .16 .22 .31 .42 .51 .56

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. 1,000 ft. X X X 1,000 ft. 1,000 ft.

Gates Item No. 7744-7015 7744-7020 7744-7030 7744-7040 7744-7050 7744-7060

*Working Pressure and Suction at +72°F (+22°C).

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Vapor Recovery for use with Gates Brahma®, Longhorn® and Master-Flex® Fuel Delivery. Can also be used for ducting, dust and light abrasive material handling. -30°F to +140°F (-34°C to +60°C) continuous service. Tube: Reinforcement: Cover:

Type U (Polyurethane). Clear. Rigid yellow PVC helix with copper static wire. Type G (PVC). Clear with yellow helix.

COUPLINGS:

7, 26, 49 or 78. Reference the Hose Coupling Section.

PACKAGING:

100' coiled and wrapped in polyethylene.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Unlabeled. Special production runs require minimum order quantities of 1,000 feet per size. No deviations allowed to above product. None.

Master-Flex® Vapor Recovery Sleeve Nom. I.D. (In.) 3 4

(mm) 76.2 101.6

INSTALLATION:

RECOMMENDED FOR:

Wt. Per Ea. (Lbs.) 5.13 7.32

(Kg) 2.33 3.32

Standard Pack 3 ft. 3 ft.

Stock (X) or Minimum Order Qty. 1 ea. 1 ea.

Gates Item No. 7744-8030 7744-8040

Apply the sleeve by twisting in a clockwise direction. Use of an appropriate lubricant, i.e. soapy water solution, will simplify sleeve application and reduce possibility of damage to hose cover. Make sure sleeve is applied prior to coupling insertion. Soft Gray PVC sleeve is designed to fit Gates Vapor Recovery Hose and provides a smooth banding surface.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 109

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Fuel Oil Delivery

Petroleum Transfer Hose

(Specification 3221FR) Nom. I.D. (In.) 1 1 1 1 1 1/4 1 1/4 1 1/4 1 1/4 1 3/8 1 3/8 1 3/8 1 3/8 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2

(mm) 25.4 25.4 25.4 25.4 31.8 31.8 31.8 31.8 34.9 34.9 34.9 34.9 38.1 38.1 38.1 38.1 38.1

Nom. O.D. (In.) 1.50 1.50 1.50 1.50 1.75 1.75 1.75 1.75 1.87 1.87 1.87 1.87 2.08 2.08 2.08 2.08 2.08

(mm) 38.1 38.1 38.1 38.1 44.5 44.5 44.5 44.5 47.5 47.5 47.5 47.5 52.8 52.8 52.8 52.8 52.8

Max. W.P. (psi) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200

(MPa) 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38

Suction (In. Hg) 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0

(mm Hg) 254 254 254 254 254 254 254 254 254 254 254 254 254 254 254 254 254

Min. Bend Radius (In.) 8.0 8.0 8.0 8.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 12.0 12.0 12.0 12.0 12.0

(mm) 203 203 203 203 254 254 254 254 254 254 254 254 305 305 305 305 305

Wt. Per Ft. (Lbs.) .58 .58 .58 .58 .75 .75 .75 .75 .80 .80 .80 .80 .95 .95 .95 .95 .95

(Kg) .26 .26 .26 .26 .34 .34 .34 .34 .36 .36 .36 .36 .43 .43 .43 .43 .43

Standard Pack 100 ft. 125 ft. 150 ft. 175 ft. 100 ft. 125 ft. 150 ft. 175 ft. 100 ft. 125 ft. 150 ft. 175 ft. 100 ft. 125 ft. 150 ft. 175 ft. 200 ft.

Stock (X) or Minimum Order Qty. X X X X X X X X X X X X X X X X X

Gates Item No. 3221-0410 3221-0411 3221-0412 3221-0413 3221-0414 3221-0415 3221-0416 3221-0417 3221-0418 3221-0419 3221-0420 3221-0421 3221-0422 3221-0423 3221-0424 3221-0425 3221-0426

(Kg) 27.67 34.25 40.82 47.63 33.11 41.39 49.67 57.95 34.93 43.66 52.39 61.12 38.56 48.19 57.83 67.47 88.45

Standard Pack 100 ft. cpld 125 ft. cpld 150 ft. cpld 175 ft. cpld 100 ft. cpld 125 ft. cpld 150 ft. cpld 175 ft. cpld 100 ft. cpld 125 ft. cpld 150 ft. cpld 175 ft. cpld 100 ft. cpld 125 ft. cpld 150 ft. cpld 175 ft. cpld 200 ft. cpld

Stock (X) or Minimum Order Qty. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea.

Gates Item No. 3221-0075 3221-0076 3221-0077 3221-0078 3221-0079 3221-0080 3221-0081 3221-0082 3221-0083 3221-0084 3221-0085 3221-0086 3221-0087 3221-0088 3221-0089 3221-0090 3221-0095

Fuel Oil Delivery Assemblies Nom. I.D. (In.) 1 1 1 1 1 1/4 1 1/4 1 1/4 1 1/4 1 3/8 1 3/8 1 3/8 1 3/8 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2

(mm) 25.4 25.4 25.4 25.4 31.8 31.8 31.8 31.8 34.9 34.9 34.9 34.9 38.1 38.1 38.1 38.1 38.1

Nom. O.D. (In.) 1.50 1.50 1.50 1.50 1.75 1.75 1.75 1.75 1.87 1.87 1.87 1.87 2.08 2.08 2.08 2.08 2.08

(mm) 38.1 38.1 38.1 38.1 44.5 44.5 44.5 44.5 47.5 47.5 47.5 47.5 52.8 52.8 52.8 52.8 52.8

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200

(MPa) 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38 1.38

Suction (In. Hg) 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0

(mm Hg) 254 254 254 254 254 254 254 254 254 254 254 254 254 254 254 254 254

Min. Bend Radius (In.) 8.0 8.0 8.0 8.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 12.0 12.0 12.0 12.0 12.0

(mm) 203 203 203 203 254 254 254 254 254 254 254 254 305 305 305 305 305

Wt. Per Ea. (Lbs.) 61.00 75.50 90.00 104.50 79.00 97.75 116.50 135.25 84.00 104.00 124.00 144.00 100.00 123.75 147.50 171.25 195.00

Transferring fuel oils or commercial gasolines in applications at temperatures as low as -40°F (-40°C). Hose remains flexible to -20°F (-29°C). For home and commercial service where a non-marking cover is required. -40°F to +180°F (-29°C to +82°C) continuous service. NOTE: Gasoline is normally conveyed below 120°F (+49°C). Tube: Reinforcement: Cover:

Type C (Nitrile). Black. High tensile synthetic textile cord. Type C4 (Carboxylated Nitrile). Red. Non-marking.

COUPLINGS:

26 or 49. Reference the Hose Coupling Section.

PACKAGING:

1" through 1 /38": Cut lengths: Packaged one each in a carton. 1 1/2": Cut lengths: Packaged one length coiled and shrink wrapped on a pallet.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous ink print label. Example: “GATES® FUEL OIL DELIVER/GASOLINE 1 1/2 INCH (38.1mm) 200 PSI (1.38MPa) WP MADE IN U.S.A.” Special production runs require minimum order quantities of 25,000 feet for all sizes. None. Tube:

RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 110

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

LP350 (Butane-Propane)

Petroleum Transfer Hose

(Specification 3220LP, 3320) Nom. I.D. (In.) 1 1/4 1 1/2 2 3

(mm) 31.8 38.1 50.8 76.2

Nom. O.D. (In.) 1.85 2.25 2.86 3.88

(mm) 47.0 57.2 72.6 98.6

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 350 350 350 350

(MPa) 2.41 2.41 2.41 2.41

Suction (In. Hg) 10.0 10.0 10.0 10.0

(mm Hg) 254 254 254 254

Min. Bend Radius (In.) 10.0 12.0 14.0 24.0

(mm) 254 305 356 610

Wt. Per Ft. (Lbs.) .89 1.35 2.01 2.77

(Kg) .40 .61 .91 1.26

Standard Pack Reel 60 ft. 60 ft. 60 ft.

Stock (X) or Minimum Order Qty. X X X X

Gates Item No. 3220-0855 3320-0935 3320-0938 3320-0934

Liquid or gaseous propane, butane or any combination of these two mixtures. Can be used for natural gas (not to exceed 50 psi) under certain conditions such as: open/outside areas and well ventilated factory buildings (if local building codes permit). Not recommended for residential, office buildings or as fuel line hose on compressed natural gas vehicles. Contact Denver Product Application (303) 744-5070 for inspection and assembly testing information. -40°F to +180°F (-40°C to +82°C) continuous service. Warning: Do not convey LP Gas over 140°F (60°C). Tube: Reinforcement: Cover:

Type A (Neoprene). 1 1/2", 2" and 3". Black. Type C (Nitrile) 1 1/4". Black. Braided, high tensile synthetic textile cord. Type A (Neoprene). Black. All sizes are perforated.

COUPLINGS:

75 Gates GLX® only for 1/4" through 1". 72 Gates Power Crimp® only for 1 1/4", 1 1/2" and 2" I.D. For Power Crimp ferrules, reference the Hose Coupling Section. Do not use male swivel, reusable or o-ring type couplings. For 3" I.D. use Dixon LP Boss only.

PACKAGING:

1 1/4": Packaged in 270' to 330' reels. Maximum of 3 pieces. Minimum length 25'. 1 1/2" through 3": Packaged 60' in a carton.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous molded strip brand label. Example: “GATES® LP350 LP-Gas Hose 2 INCH DO NOT EXCEED 350 PSI WP Made In U.S.A. Special production runs require minimum order quantities of 5,000 feet for 1 1/4" and 600 feet for 1 1/2" through 3". Any other size in specified lengths requires a minimum production order. For price, add 15% (x1.15) to price. None. CAN/CGA-8.1-M86. NFPA 58, Section 2-4.6. Underwriters Laboratories Standard No. 21. (Applies to all sizes).

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 111

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

LP350X (Butane-Propane)

Petroleum Transfer Hose

(Specification 3220SP) Nom. I.D. (In.) 1/4 1/4 3/8 3/8 1/2 1/2 3/4 3/4 3/4 3/4 1 1 1 1

(mm) 6.4 6.4 9.5 9.5 12.7 12.7 19.1 19.1 19.1 19.1 25.4 25.4 25.4 25.4

Nom. O.D. (In.) .58 .58 .74 .74 .91 .91 1.23 1.23 1.23 1.23 1.51 1.51 1.51 1.51

(mm) 14.7 14.7 18.8 18.8 23.1 23.1 31.2 31.2 31.2 31.2 38.4 38.4 38.4 38.4

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 350 350 350 350 350 350 350 350 350 350 350 350 350 350

(MPa) 2.41 2.41 2.41 2.41 2.41 2.41 2.41 2.41 2.41 2.41 2.41 2.41 2.41 2.41

Suction (In. Hg) 30.0 30.0 30.0 30.0 25.0 25.0 20.0 20.0 20.0 20.0 15.0 15.0 15.0 15.0

(mm Hg) 762 762 762 762 635 635 508 508 508 508 381 381 381 381

Min. Bend Radius (In.) 3.0 3.0 3.0 3.0 5.0 5.0 6.0 6.0 6.0 6.0 8.0 8.0 8.0 8.0

(mm) 76 76 76 76 127 127 152 152 152 152 203 203 203 203

Wt. Per Ft. (Lbs.) .14 .14 .21 .21 .28 .28 .44 .44 .44 .44 .60 .60 .60 .60

(Kg) .06 .06 .10 .10 .13 .13 .20 .20 .20 .20 .27 .27 .27 .27

Standard Pack Reel Bulk Reel Bulk Reel Bulk Reel 100 ft. 125 ft. 150 ft. Reel 100 ft. 125 ft. 150 ft.

Stock (X) or Minimum Order Qty. X 3700 ft. (X) X 2000 ft. (X) X 1000 ft. (X) X X X X X X X X

Gates Item No. 3220-1200 3220-1201 3220-1202 3220-1203 3220-1204 3220-1205 3220-1206 3220-1207 3220-1208 3220-1209 3220-1210 3220-1211 3220-1212 3220-1213

Type C (Nitrile). Black. High tensile synthetic textile cord. Type A (Neoprene). Black. All sizes are perforated.

COUPLINGS:

75 Gates GLX®. Do not use male swivel, reusable or o-ring type couplings. Reference the Hose Coupling Section.

PACKAGING:

1/4" Bulk Pack: Packaged 3700' in a pallet carton. Maximum 10 pieces. Maximum of 6 pieces under 25'. Minimum length 10'. 1/4" through 1/2": Packaged in 600' to 800' reels. Maximum 4 pieces. One length 25' to 50'. Maximum of 2 pieces under 100'. 3/8" Bulk Pack: Packaged 2000' in a pallet carton. Maximum 10 pieces. Maximum of 6 pieces under 25'. Minimum length 10'. 1/2" Bulk Pack: Packaged 1000' in a pallet carton. Maximum 10 pieces. All lengths in increments of 25'. Minimum length 25'. 3/4" and 1" Cut lengths: Coiled in cartons. 3/4" through 1": Packaged in 300' to 400' reels. Maximum 3 pieces. One length 25' to 50'. All other lengths over 50'. Maximum of 2 pieces under 100'.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous molded strip brand label. Example: “GATES® LP350X UL/CGA TYPE 1 LP-Gas Hose 1 INCH DO NOT EXCEED 350 PSI WP Made In U.S.A.” Special production runs require minimum order quantities of 25,000 feet. 3/4" and 1" cut lengths are available as standard items as listed. Any other size in specified lengths requires a minimum production order. For price add 15% (x1.15) to reel price. None. CAN/CGA-8.1-M86 Type 1. NFPA 58, Section 2-4.6. Underwriters Laboratories Standard No. 21. (Applies to all sizes).

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 112

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

LPG Vapor

Petroleum Transfer Hose

(Specification 3220E) Nom. I.D. (In.) 3/16 1/4 3/8

(mm) 4.8 6.4 9.5

Nom. O.D. (In.) .44 .53 .66

(mm) 11.2 13.5 16.8

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 125 125 125

(MPa) .86 .86 .86

Suction (In. Hg) 30.0 30.0 25.0

(mm Hg) 762 762 635

Min. Bend Radius (In.) 2.0 3.0 3.0

(mm) 51 76 76

Wt. Per Ft. (Lbs.) .08 .11 .14

(Kg) .04 .05 .06

Standard Pack Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X

Gates Item No. 3220-0451 3220-0456 3220-0461

Flexible connector for conveying low pressure LPG (vapor only) to many types of farm and industrial heating applications; e.g., space heaters. NOTE: This hose should not be used for liquid LPG or in UL approved appliances such as barbecue grills. -30°F to +150°F (-34°C to +66°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. High tensile synthetic textile cord. Type A (Neoprene). Black.

PACKAGING:

3/16" through 3/8": Packaged in 600' to 800' reels. Maximum 4 pieces. One length 25' to 50'. Maximum of 2 lengths under 100'.

BRANDING:

Continuous ink print label. Example: “GATES® LPG Vapor 3/8 Inch (9.5mm) 125 PSI (.86MPa) WP Made In U.S.A.”

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Special production runs require minimum order quantities of 25,000 feet per size. None. Underwriters Laboratories Standard No. 569. (Applies to hose assemblies only).

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 113

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Blacksnake® (Curb Pump Hardwall)

Petroleum Transfer Hose

(Specification 3624) Nom. I.D. (In.) 5/8 3/4 1

(mm) 15.9 19.1 25.4

Nom. O.D. (In.) 1.00 1.13 1.38

(mm) 25.4 28.7 35.1

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 150

(MPa) 1.03 1.03 1.03

Suction (In. Hg) 30.0 30.0 30.0

(mm Hg) 762 762 762

Min. Bend Radius (In.) 6.0 6.0 8.0

(mm) 152 152 203

Wt. Per Ft. (Lbs.) .37 .42 .57

(Kg) .17 .19 .26

Standard Pack Reel Reel Reel

-40°F to +120°F (-40°C to +49°C) continuous service. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Braided, high tensile steel wire. Type J (CPE). Black.

24. Reference the Hose Coupling Section.

PACKAGING:

5/8" through 1": Packaged 500' per reel. Maximum 5 pieces. Minimum length 12'.

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Gates Item No. 3624-0001 3624-0002 3624-0003

Dispensing all types of commercial gasolines, or other petroleum based products, from service station pumps. A heavy duty hardwall hose which does not collapse in reel use or behind the nozzle in heavy duty service.

COUPLINGS:

BRANDING:

Stock (X) or Minimum Order Qty. X X X

Continuous transfer label. Example: “GATES® BLACKSNAKE® 3/4 Inch (19.1mm) 1 wire braid (UL) Listed Gasoline Hose Made In U.S.A.” Special production runs require minimum order quantities of 5,000 feet per size. None. Underwriters Laboratories Standard No. 330. (USA and Canada). Tube: RMA (Class A) High oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 114

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

PowerClean™ - 1 Wire Braid

Pressure Washer

(Specification 4657, KB, KG, KK, KY, PB, PG, PY) PowerClean™ 2500 Color Black Black Blue Gray Yellow

Nom. I.D. (In.) 1/2 1/2 1/2 1/2 1/2

(mm) 12.7 12.7 12.7 12.7 12.7

Nom. O.D. (In.) .80 .80 .80 .80 .80

(mm) 20.3 20.3 20.3 20.3 20.3

Max. W.P. (psi) 2500 2500 2500 2500 2500

(mm) 17.3 17.3 17.3 17.3 17.3 17.3

Max. W.P. (psi) 3000 3000 3000 3000 3000 3000

(mm) 13.5 13.5 13.5 13.5 13.5

Max. W.P. (psi) 3500 3500 3500 3500 3500

(mm) 17.3 17.3 17.3 17.3 17.3

Max. W.P. (psi) 4000 4000 4000 4000 4000

(MPa) 17.24 17.24 17.24 17.24 17.24

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0

(MPa) 20.68 20.68 20.68 20.68 20.68 20.68

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0

(MPa) 24.13 24.13 24.13 24.13 24.13

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0

(MPa) 27.58 27.58 27.58 27.58 27.58

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762

Min. Bend Radius (In.) 7.0 7.0 7.0 7.0 7.0

(mm Hg) 762 762 762 762 762 762

Min. Bend Radius (In.) 5.0 5.0 5.0 5.0 5.0 5.0

(mm Hg) 762 762 762 762 762

Min. Bend Radius (In.) 4.0 4.0 4.0 4.0 4.0

(mm Hg) 762 762 762 762 762

Min. Bend Radius (In.) 5.0 5.0 5.0 5.0 5.0

(mm) 178 178 178 178 178

Wt. Per Ft. (Lbs.) .28 .28 .28 .28 .28

(Kg) .13 .13 .13 .13 .13

Standard Pack Reel Lg. Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X 5,000 ft. X 5,000 ft. X

Gates Item No. 4657-2408 4657-2412 4657-2413 4657-2414 4657-2415

(mm) 127 127 127 127 127 127

Wt. Per Ft. (Lbs.) .23 .23 .23 .23 .23 .23

(Kg) .10 .10 .10 .10 .10 .10

Standard Pack Lg. Reel Reel Lg. Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X X X X

Gates Item No. 4657-2401 4657-2402 4657-2403 4657-2404 4657-2416 4657-2417

(mm) 102 102 102 102 102

Wt. Per Ft. (Lbs.) .15 .15 .15 .15 .15

(Kg) .07 .07 .07 .07 .07

Standard Pack Reel Lg. Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X X 5,000 ft.

Gates Item No. 4657-2400 4657-2418 4657-2419 4657-2420 4657-2421

(mm) 127 127 127 127 127

Wt. Per Ft. (Lbs.) .23 .23 .25 .23 .23

(Kg) .10 .10 .10 .10 .10

Standard Pack Reel Lg. Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X 5,000 ft. 5,000 ft.

Gates Item No. 4657-2225 4657-2405 4657-2422 4657-2423 4657-2424

PowerClean™ 3000 Color Black Black Blue Blue Gray Yellow

Nom. I.D. (In.) 3/8 3/8 3/8 3/8 3/8 3/8

(mm) 9.5 9.5 9.5 9.5 9.5 9.5

Nom. O.D. (In.) .68 .68 .68 .68 .68 .68

PowerClean™ 3500 Color Black Black Blue Gray Yellow

Nom. I.D. (In.) 1/4 1/4 1/4 1/4 1/4

(mm) 6.4 6.4 6.4 6.4 6.4

Nom. O.D. (In.) .53 .53 .53 .53 .53

PowerClean™ 4000 Color Black Black Blue Gray Yellow

Nom. I.D. (In.) 3/8 3/8 3/8 3/8 3/8

(mm) 9.5 9.5 9.5 9.5 9.5

Nom. O.D. (In.) .68 .68 .68 .68 .68

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Heavy-duty use on hot and cold water high pressure cleaning equipment where heavy duty service is required. Flexible. Use Bend Restrictors to extend service life. NOTE: Not recommended for steam service. -40°F to +250°F (-40°C to +121°C). Laboratory tested for normal service. Increased operating temperatures will reduce hose assembly service life. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Specially compounded to handle high pressure water service. High tensile steel one-wire braid. Type C2 (Modified Nitrile). Black, Blue, Gray, Yellow. Specially compounded to handle pressure washer environment. (Blue, Gray and Yellow covers are non-marking).

COUPLINGS:

74 MegaCrimp® couplings. Reference the Hose Coupling Section.

PACKAGING:

1/4" through 1/2": Packaged in 1000' large reels. Any number of pieces. All lengths in 50' increments. Minimum length 50'. 1/4" through 1/2": Packaged in 300' reels. Any number of pieces. All lengths in 50' increments. Minimum length 50'.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Continuous ink brand. Example: “GATES® 3/8 Inch PowerClean™ 3000 Max WP 3000 PSI Not For Steam Service Made In U.S.A.” Special production runs require minimum order quantities of 5,000 feet per size. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 115

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

PowerClean™ - 2 Wire Braid

Pressure Washer

(Specification 4657F, XB, XG, XY) PowerClean™ 4000 Color Black Black Blue Gray Yellow

Nom. I.D. (In.) 1/2 1/2 1/2 1/2 1/2

(mm) 12.7 12.7 12.7 12.7 12.7

Nom. O.D. (In.) .86 .86 .86 .86 .86

(mm) 21.8 21.8 21.8 21.8 21.8

Max. W.P. (psi) 4000 4000 4000 4000 4000

(mm) 18.8 18.8 18.8 18.8 18.8

Max. W.P. (psi) 5000 5000 5000 5000 5000

(mm) 15.0

Max. W.P. (psi) 6000

(MPa) 27.58 27.58 27.58 27.58 27.58

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0

(MPa) 34.47 34.47 34.47 34.47 34.47

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0

(MPa) 41.37

Suction (In. Hg) 30.0

(mm Hg) 762 762 762 762 762

Min. Bend Radius (In.) 7.0 7.0 7.0 7.0 7.0

(mm Hg) 762 762 762 762 762

Min. Bend Radius (In.) 5.0 5.0 5.0 5.0 5.0

(mm Hg) 762

Min. Bend Radius (In.) 4.0

(mm) 178 178 178 178 178

Wt. Per Ft. (Lbs.) .42 .42 .42 .42 .42

(mm) 127 127 127 127 127

Wt. Per Ft. (Lbs.) .35 .35 .35 .35 .35

(mm) 102

Wt. Per Ft. (Lbs.) .25

(Kg) .19 .19 .19 .19 .19

Standard Pack Lg. Reel Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. 5,000 ft. X 5,000 ft. 5,000 ft. 5,000 ft.

Gates Item No. 4657-2425 4657-2426 4657-2409 4657-2427 4657-2428

(Kg) .16 .16 .16 .16 .16

Standard Pack Lg. Reel Reel Reel Reel Reel

Stock (X) or Minimum Order Qty. X X X 5,000 ft. 5,000 ft.

Gates Item No. 4657-2406 4657-2407 4657-2429 4657-2430 4657-2431

(Kg) .11

Standard Pack Reel

Stock (X) or Minimum Order Qty. X

Gates Item No. 4657-2410

PowerClean™ 5000 Color Black Black Blue Gray Yellow

Nom. I.D. (In.) 3/8 3/8 3/8 3/8 3/8

(mm) 9.5 9.5 9.5 9.5 9.5

Nom. O.D. (In.) .74 .74 .74 .74 .74

PowerClean™ 6000 Color Black

Nom. I.D. (In.) 1/4

(mm) 6.4

Nom. O.D. (In.) .59

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Type C (Nitrile). Black. Specially compounded to handle high pressure water service. High tensile steel two-wire braid. Type C2 (Modified Nitrile). Black, Blue, Gray, Yellow. Specially compounded to handle pressure washer environment. (Blue, Gray and Yellow covers are non-marking).

COUPLINGS:

74 MegaCrimp® couplings. Reference the Hose Coupling Section.

PACKAGING:

1/4" through 1/2": Packaged in 300' reels. Any number of pieces. All lengths in 50' increments. Minimum length 50'. 3/8" and 1/2": Packaged in 1000' large reels. Any number of pieces. All lengths in 50' increments. Minimum length 50'.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Continuous ink brand. Example: “GATES® 3/8 Inch PowerClean™ 5000 Max WP 5000 PSI Not For Steam Service Made In U.S.A.” Special production runs require minimum order quantities of 5,000 feet per size. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 116

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Pressure Washer Assemblies

Pressure Washer

(Specification 3603PW) Nom. I.D. (In.) 1/4 3/8 3/8 1/2

(mm) 6.4 9.5 9.5 12.7

Nom. O.D. (In.) .48 .63 .63 .76

(mm) 12.2 16.0 16.0 19.3

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 3000 3000 3000 3000

(MPa) 20.68 20.68 20.68 20.68

Suction (In. Hg) 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762

Min. Bend Radius (In.) 4.0 5.0 5.0 7.0

(mm) 102 127 127 178

Wt. Per Ea. (Lbs.) 5.50 8.50 8.50 11.50

(Kg) 2.50 3.86 3.86 5.22

Gates Item No. 3604-0034 3604-0035 3604-0071 3604-0036

-40°F to +250°F (-40°C to +121°C). Laboratory tested for normal service. Increased operating temperatures will reduce hose assembly service life. Tube: Reinforcement: Cover:

Type C (Nitrile). Black. Specially compounded to handle high pressure water service. High tensile steel one-wire braid. Type C2 (Modified Nitrile). Black. Specially compounded to handle pressure washer environment. Bend restrictors applied on each end.

COUPLINGS:

Gates permanent couplings (MP/MPX). Factory coupled assemblies only. 1/4" 3/8" 3/8" 1/2"

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Stock (X) or Minimum Order Qty. 5 ea. (X) 5 ea. (X) 50 ea. 5 ea. (X)

Standard duty use on hot and cold water high pressure cleaning equipment. Extremely flexible, lightweight and easy to handle. NOTE: Not recommended for steam service.

PACKAGING:

BRANDING:

Standard Pack 50 ft. 50 ft. 100 ft. 50 ft.

x x x x

50': Coiled in a carton, 5 assemblies per carton. 100': Coiled in a carton, 5 assemblies per carton. 50': Coiled in a carton, 5 assemblies per carton. 100': Coiled in a carton, 5 assemblies per carton.

Continuous ink brand. Example: “GATES® 3/8 Inch Pressure Washer Max 3000 PSI Not For Steam Service Made In Mexico” Special production runs require minimum order quantities of 5,000 feet per size. None.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 117

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Cyclone®

Pressure Washer

(Specification 3217HY) Nom. I.D. (In.) 3/8 3/8 1/2 1/2 3/4

(mm) 9.5 9.5 12.7 12.7 19.1

Nom. O.D. (In.) .73 .73 .94 .94 1.20

(mm) 18.5 18.5 23.9 23.9 30.5

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 1000 1000 1000 1000 1000

(MPa) 6.90 6.90 6.90 6.90 6.90

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762

Min. Bend Radius (In.) 4.0 4.0 5.0 5.0 6.0

(mm) 102 102 127 127 152

Wt. Per Ft. (Lbs.) .18 .18 .29 .29 .41

(Kg) .08 .08 .13 .13 .19

Standard Pack 100 ft. Reel Reel 100 ft. Reel

Stock (X) or Minimum Order Qty. X X X 5,000 ft. X

Gates Item No. 3217-0584 3217-0585 3217-0586 3217-0587 3217-0588

High-pressure washer operations using mild detergents in meat and poultry plants. Cover is resistant to weather, oil, animal fat, abrasion and heat encountered in packing plant cleaning applications. Air service working pressure is 300 psi for all sizes. -40°F to +212°F (-40°C to +100°C) continuous washdown service. Tube: Reinforcement: Cover:

Type C2 (Modified Nitrile). Black. Braided, synthetic high tensile cord. Type C2 (Modified Nitrile). Yellow. (Red, green and blue cover available on special order).

COUPLINGS:

75 Gates GLX®. Reference the Hose Coupling Section.

PACKAGING:

3/8" through 3/4": Packaged in 500' to 750' reels. Maximum 3 pieces. Minimum length 50'. 3/8" x 100': Packaged 500' in a pallet box. Each length coiled and tied. 1/2" x 100': Packaged 500' in a pallet box. Each length coiled and tied.

BRANDING:

Continuous ink print label. Example: “GATES® Cyclone® Washdown 3/8 Inch (9.5mm) 1000 PSI (6.90MPa) WP Made In U.S.A.”

SPECIAL ORDER REQUIREMENTS:

Red, green and blue covers are made to order and require 5,000 feet orders per size/color. Contact Gates Corporation for pricing, order requirements and availability. Special production runs require minimum order quantities of 5,000 feet per size. For special requirements contact Gates Corporation.

REMNANT LENGTHS:

None.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 118

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Creamery/Paper Mill Washdown

Pressure Washer

(Specification 3213B/3325T) Without Nozzle (3213B) Nom. I.D. (In.) 1/2 3/4 3/4 1 1

(mm) 12.7 19.1 19.1 25.4 25.4

Nom. O.D. (In.) .91 1.25 1.25 1.52 1.52

(mm) 23.1 31.8 31.8 38.6 38.6

Max. W.P. (psi) 200 200 200 200 200

(MPa) 1.38 1.38 1.38 1.38 1.38

Suction (In. Hg) 25.0 15.0 15.0 15.0 15.0

(MPa) 1.03 1.03 1.03

Suction (In. Hg) 25.0 15.0 15.0

(mm Hg) 635 381 381 381 381

Min. Bend Radius (In.) 5.0 6.0 6.0 8.0 8.0

(mm) 127 152 152 203 203

Wt. Per Ft. (Lbs.) .28 .49 .49 .65 .65

(Kg) .13 .22 .22 .30 .30

Standard Pack Reel 50 ft. Reel Reel 50 ft.

Stock (X) or Minimum Order Qty. X X X 25,000 ft. X

Gates Item No. 3213-0401 3213-0413 3213-0501 3213-0415 3213-0416

(Kg) 12.47 15.20 17.92

Standard Pack 50 ft. 50 ft. 50 ft.

Stock (X) or Minimum Order Qty. 1 ea. (X) 1 ea. (X) 1 ea. (X)

Gates Item No. 3213-0543 3213-0544 3213-0545

With Nozzle (3325T) Nom. I.D. (In.) 3/4 1 1 1/4

(mm) 19.1 25.4 31.8

Nom. O.D. (In.) 1.25 1.50 1.75

(mm) 31.8 38.1 44.5

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 150

(mm Hg) 635 381 381

Min. Bend Radius (In.) 6.0 8.0 10.0

(mm) 152 203 254

Wt. Per Ea. (Lbs.) 27.50 33.50 39.50

CAUTION: NOT RECOMMENDED FOR USE WITH STEAM. Cold and hot water up to 212°F (100°C) where steam is injected into the water. Used for paper mill, food handling or processing plant washdown service requiring hose with a non-marking cover. -20°F to +180°F (-29°C to +82°C) continuous service. For nozzle only. -40°F to +212°F (-40°C to +100°C) continuous service. Tube: Reinforcement: Cover:

Type D (SBR). Black. For nozzle only. Type P (EPDM). Black. Braided, high tensile synthetic textile cord. For nozzle only. Synthetic, high tensile textile cord. Type D (Natural Rubber). Gray with green stripe. For nozzle only. Type P (EPDM). White. All sizes are perforated on plain end hose only.

COUPLINGS:

1, 14, 15 or 75 Gates GLX® (For without nozzle only). Reference the Hose Coupling Section.

PACKAGING:

1/2": Packaged in 600' to 800' reels. Maximum 4 pieces. Minimum length 25'. 3/4" and 1": Packaged in 300' to 400' reels. Maximum 3 pieces. One length 25' to 50'. Maximum of 2 lengths under 100'. 50' lengths (with nozzle): Packaged each length coiled and wrapped in polyethylene. 50' lengths (without nozzle): Packaged 50' coiled in a carton.

BRANDING:

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Continuous ink print label. Example: “GATES® WASHDOWN 3/4 INCH (19.1mm) 200 PSI (1.38MPa) WP MADE IN U.S.A.” Continuous transfer label. Example: “GATES® WASHDOWN 3/4 INCH (19.1mm) 150 PSI (1.03MPa) WP MADE IN MEXICO” Special production runs require minimum order quantities of 25,000 feet for plain end hose and 600 feet for 3/4" through 1 1/4" with nozzle. None.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 119

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

205MB Steam King®

Steam Hose

(Specification 3605) Smooth Cover Nom. I.D. (In.) 3/8 3/8 1/2 1/2 1/2 3/4 3/4 3/4 1

(mm) 9.5 9.5 12.7 12.7 12.7 19.1 19.1 19.1 25.4

Nom. O.D. (In.) .78 .78 1.06 1.06 1.06 1.28 1.28 1.28 1.63

(mm) 19.8 19.8 26.9 26.9 26.9 32.5 32.5 32.5 41.4

Max. W.P. (psi) 250 250 250 250 250 250 250 250 250

(mm) 32.3 38.6 38.6 46.0 54.4 67.6

Max. W.P. (psi) 250 250 250 250 250 250

(MPa) 1.72 1.72 1.72 1.72 1.72 1.72 1.72 1.72 1.72

Suction (In. Hg) 30.0 30.0 25.0 25.0 25.0 20.0 20.0 20.0 20.0

(MPa) 1.72 1.72 1.72 1.72 1.72 1.72

Suction (In. Hg) 20.0 20.0 20.0 20.0 10.0 10.0

(mm Hg) 762 762 635 635 635 508 508 508 508

Min. Bend Radius (In.) 4.0 4.0 7.0 7.0 7.0 9.0 9.0 9.0 11.0

(mm Hg) 508 508 508 508 254 254

Min. Bend Radius (In.) 9.0 11.0 11.0 16.0 20.0 25.0

(mm Hg) 508 508 508

Min. Bend Radius (In.) 9.0 9.0 9.0

(mm) 102 102 178 178 178 229 229 229 279

Wt. Per Ft. (Lbs.) .26 .26 .40 .40 .40 .49 .49 .49 .78

(Kg) .12 .12 .18 .18 .18 .22 .22 .22 .35

Standard Pack 50 ft. Reel 50 ft. Reel 50 ft.-BP** 50 ft. Reel 50 ft.-BP** Reel

Stock (X) or Minimum Order Qty. 250 ft. (X) X 200 ft. (X) X 1,500 ft. (X) 150 ft. (X) X 1,000 ft. (X) X

Gates Item No. 3605-0650 3605-0652 3605-0655 3605-0672 3605-0677 3605-0664 3605-0678 3605-0679 3605-0668

(mm) 229 279 279 406 508 635

Wt. Per Ft. (Lbs.) .57 .70 .70 .90 1.21 1.57

(Kg) .26 .32 .32 .41 .55 .71

Standard Pack 50 ft. 50 ft. 50 ft.-BP** 50 ft. 50 ft. 50 ft.

Stock (X) or Minimum Order Qty. 100 ft. (X) 200 ft. (X) 600 ft. (X) 100 ft. (X) X X

Gates Item No. 3605-0901 3605-0665 3605-0669 3605-0671 3605-0676 3605-0681

(mm) 229 229 229

Wt. Per Ea. (Lbs.) 31.90 30.90 29.90

(Kg) 14.47 14.02 13.56

Standard Pack 50 ft. F/F 50 ft. F/M 50 ft. M/M

Stock (X) or Minimum Order Qty. 1 ea. (X) 1 ea. (X) 1 ea. (X)

Gates Item No. 3605-0736 3605-0737 3605-0738

Wrapped Cover Nom. I.D. (In.) 3/4 1 1 1 1/4 1 1/2 2

(mm) 19.1 25.4 25.4 31.8 38.1 50.8

Nom. O.D. (In.) 1.27 1.52 1.52 1.81 2.14 2.66

205MB Assemblies Wrapped Cover Nom. I.D. (In.) 3/4 3/4 3/4

(mm) 19.1 19.1 19.1

Nom. O.D. (In.) 1.27 1.27 1.27

(mm) 32.3 32.3 32.3

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 250 250 250

(MPa) 1.72 1.72 1.72

Suction (In. Hg) 20.0 20.0 20.0

NOTE: DO NOT ALTERNATE USE BETWEEN STEAM AND WATER. -40°F to +450°F (-40°C to +232°C) continuous service. Tube: Reinforcement: Cover:

Type P2 (EPDM). Black. Braided, high tensile steel wire. Type P2 (EPDM). Black. All sizes are perforated.

COUPLINGS:

14, 15, or 76 only. Reference the Hose Coupling Section.

PACKAGING:

**BP - Bulk Pack, 50' coiled and tied in a pallet carton: 1/2" - 1,500'; 3/4" - 1,000'; 1" - 600'. 3/8" x 50': Packaged 250' per carton, each length coiled and tied. 3/8": Packaged in 200' to 300' reels. Maximum of 3 pieces. Minimum length 25'. One length under 100'. 1/2" x 50': Packaged 200' per carton, each length coiled and tied. 3/4" x 50" coupled assy: Coiled in carton, one assembly per carton. 3/4" x 50': Packaged 100' or 150' per carton, each length coiled and tied. 1" x 50': Packaged 200' per carton, each length coiled and tied. 1 1/4" x 50': Packaged 100' per carton, each length coiled and tied. 1 1/2" and 2" x 50': Packaged 50' per carton, each length coiled and tied. 1/2", 3/4" and 1": Packaged in 500' reels. Maximum of 3 pieces. All lengths in 50' increments.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Continuous molded brand. Example: “GATES® 205MB STEAM KING® 3/4 INCH 2 WIRE BRAID 250 PSI WP AT 450°F MADE IN U.S.A. CAUTION: TIGHTEN CLAMPS BEFORE USING.” Special production runs require minimum order quantities of 5,000 feet. None.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 120

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

232MB Steam Queen®

Steam Hose

(Specification 3602EL) Nom. I.D. (In.) 3/8 3/8 1/2 1/2 3/4 3/4 1 1 1/2 2

(mm) 9.5 9.5 12.7 12.7 19.1 19.1 25.4 38.1 50.8

Nom. O.D. (In.) .80 .80 1.02 1.02 1.27 1.27 1.52 2.18 2.66

(mm) 20.3 20.3 25.9 25.9 32.3 32.3 38.6 55.4 67.6

Max. W.P. (psi) 250 250 250 250 250 250 250 250 250

(MPa) 1.72 1.72 1.72 1.72 1.72 1.72 1.72 1.72 1.72

Suction (In. Hg) 30.0 30.0 25.0 25.0 20.0 20.0 20.0 10.0 10.0

(mm Hg) 762 762 635 635 508 508 508 254 254

Min. Bend Radius (In.) 4.0 4.0 7.0 7.0 9.0 9.0 11.0 20.0 25.0

(mm) 102 102 178 178 229 229 279 508 635

Wt. Per Ft. (Lbs.) .30 .30 .45 .45 .60 .60 .73 1.24 1.64

(Kg) .14 .14 .20 .20 .27 .27 .33 .56 .74

Standard Pack 50 ft. Reel 50 ft. Reel 50 ft. Reel 50 ft. 50 ft. 50 ft.

Stock (X) or Minimum Order Qty. X X X X X X X X X

Gates Item No. 3602-1051 3602-1061 3602-1052 3602-1062 3602-1055 3602-1065 3602-1057 3602-1059 3602-1060

(Kg) 15.15 14.70 14.24

Standard Pack 50 ft. F/F 50 ft. F/M 50 ft. M/M

Stock (X) or Minimum Order Qty. 1 ea. (X) 1 ea. (X) 1 ea. (X)

Gates Item No. 3602-0002 3602-0003 3602-0004

232MB Assemblies Wrapped Cover Nom. I.D. (In.) 3/4 3/4 3/4

(mm) 19.1 19.1 19.1

Nom. O.D. (In.) 1.27 1.27 1.27

(mm) 32.3 32.3 32.3

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 250 250 250

(MPa) 1.72 1.72 1.72

Suction (In. Hg) 20.0 20.0 20.0

(mm Hg) 508 508 508

Min. Bend Radius (In.) 9.0 9.0 9.0

(mm) 229 229 229

Wt. Per Ea. (Lbs.) 33.40 32.40 31.40

All types of steam - saturated and superheated - up to 250 PSI and +450°F (+232°C). NOTE: DO NOT ALTERNATE USE BETWEEN STEAM AND WATER. -40°F to +450°F (-40°C to +232°C) continuous service. Tube: Reinforcement: Cover:

Type P2 (EPDM). Black. Braided, high tensile steel wire. Type B1 (Special compound designed to withstand heat and oil). Red. All sizes are perforated.

COUPLINGS:

14, 15, or 76 only. Reference the Hose Coupling Section.

PACKAGING:

3/8" through 3/4": Packaged in 200' to 300' reels. Maximum of 3 pieces. Minimum length 25'. One length under 100'. 3/4" x 50" coupled assy: Coiled in carton, one assembly per carton. 50' lengths: Coiled in a carton.

BRANDING:

SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS: STANDARDS:

Continuous molded brand. Example: “GATES® 232MB STEAM QUEEN® 3/4 INCH 2 WIRE BRAID 250 PSI WP AT 450°F MADE IN U.S.A. (assemblies only) Continuous molded brand. Example: ”GATES® 232MB STEAM QUEEN® 3/4 INCH 2 WIRE BRAID 250 PSI WP AT 450°F MADE IN U.S.A. CAUTION: TIGHTEN CLAMPS BEFORE USING.’ Special production runs require minimum order quantities of 5,000 feet for sizes less than 1 1/2" and 600 feet for 1 1/2" and larger. None. Cover:

RMA (Class C) Limited oil resistance.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 121

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Steam and Its Effect on Hose Water can exist in three different basic states — solid, liquid or gas — and there are three different conditions of the gas (steam). Which particular condition exists is dictated by the pressure and temperature existing.

These conditions are: Wet Saturated Steam or “Wet Steam” Dry Saturated Steam Superheated Steam or “Dry Steam”

By way of explanation, refer to the steam chart. The heavy black line is the boiling point of water at various gauge pressures. Any point on this line represents saturated steam. Saturated steam may be completely free of unvaporized water particles, or it may carry such particles. In other words, saturated steam may be “Dry” or “Wet.” Any point below the line represents Hot Water — any point above the line represents Superheated Steam.

The dotted line shows the process of saturated steam being transformed into superheated steam. If a steam line is at a pressure of 150 psi, and a temperature of 366ºF., it contains saturated steam. If the pressure is substantially reduced by the expansion of the steam (such as the sudden opening of a valve or the steam passing into a larger pipe or hose), the condition of the steam follows the dotted line to some point X in the superheated steam area. This condition may not last very long, but the superheated steam tends to deteriorate the tube stock in ordinary steam hose intended for use with saturated steam. This usually results in hose failure.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 122

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

How to Select The Correct Steam Hose Assembly 1.

Determine Required Hose Size The hose size required is usually fixed by size of fittings or pipe to which the hose is to be connected. It is important that you do not select a hose with inside diameter larger than the diameter of the preceding pipe.

STEAM HOSE TABLE Recommended Service Rated Working Pressure (psi)

Working Temperature (°F)

232MB ® Steam Queen

250

450

Determine Condition of Steam (Saturated or Superheated) Locate the actual Rated Working Pressure and Temperature on the steam chart on previous page. Any point on the heavy line is saturated steam.

205MB ® Steam King

250

450

Select the Correct Hose From the table at right, select the hose that fulfills the requirements of both the condition of the team and the Rated Working Pressure.

Gauge Pressure (psi)

*Temperature of Saturated Steam (ºF)

Gauge Pressure (psi)

*Temperature of Saturated Steam (ºF)

Gauge Pressure (psi)

*Temperature of Saturated Steam (ºF)

10 25 30 35 40

239 267 274 281 287

110 115 120 125 130

344 347 350 353 356

200 205 210 215 220

388 390 392 394 395

45 50 55 60 65 70 75 80 85 90

292 298 303 307 312 316 320 324 328 331

135 140 145 150 155 160 165 170 175 180

358 361 363 366 368 371 373 375 377 380

225 230 235 240 245 250 255 260 265 270

397 399 401 403 404 406 408 409 411 413

95 335 185 382 100 338 190 384 105 341 195 386 *Based on an atmosphere pressure of 14.7 psi.

275

414

Find Actual Rated Working Pressure and Temperature Take pressure and temperature readings just ahead of the hose connection.

Determine Length Required Length required is almost always dictated by the application. Select Couplings Required Gates recommends interlocking* and permanent crimped types of couplings for steam hose applications. These are identified as: 14 Interlocking, ground joint 15 Interlocking, washer joint 76 Permanent Crimped Steam Hose Couplings

Hose Type

Type of Steam Saturated or Superheated Saturated or Superheated

Properties of Saturated Steam th (Abridged from Handbook of Chemistry and Physics – 39 Edition.)

*Remember to retighten bolts on a regular basis. 7.

Maintenance and Inspection For proper maintenance and inspection of interlocking and permanent crimped steam hose assemblies, refer to RMA IP-11-1.

IMPORTANT: Steam can be dangerous material. Play it safe – stay within the limits of published recommendations!

Do Not Alternate Use Between Steam and Water

NOTE: When electrical continuity is required, ground the wire braid in the hose to couplings with aluminum, copper or stainless steel staples.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 123

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Shark®

Water Hose

(Specification 4686AR/4686DC) Nom. I.D. (In.) 1 1 1/4 1 1/2 2 2 2 1/2 3 4 5 6 6 6

(mm) 25.4 31.8 38.1 50.8 50.8 63.5 76.2 101.6 127.0 152.4 152.4 152.4

Nom. O.D. (In.) 1.45 1.71 1.96 2.46 2.46 3.02 3.58 4.58 5.60 6.65 6.65 6.65

(mm) 36.8 43.4 49.8 62.5 62.5 76.7 90.9 116.3 142.2 168.9 168.9 168.9

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 150 150 150 150 150 150 100 100 100 100

(MPa) 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 .69 .69 .69 .69

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 5.0 6.0 8.0 10.0 10.0 12.0 15.0 20.0 25.0 30.0 30.0 30.0

(mm) 127 152 203 254 254 305 381 508 635 762 762 762

Wt. Per Ft. (Lbs.) .53 .68 .79 1.01 1.01 1.46 2.01 2.62 3.89 4.84 4.84 4.84

(Kg) .24 .31 .36 .46 .46 .66 .91 1.19 1.76 2.20 2.20 2.20

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 200 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 20 ft. 25 ft.

Stock (X) or Minimum Order Qty. X X X X 400 ft. X X X X X X X

Gates Item No. 4686-0701 4686-0702 4686-0703 4686-0704 4686-0710 4686-0705 4686-0706 4686-0707 4686-0708 4686-0709 4686-0711 4686-0712

Suction hose used to convey water, detergents, phosphate ester hydraulic fluids and dilute solutions of acids, alkalies and glycols. -40°F to +180°F (-40°C to +82°C) continuous service. Tube: Reinforcement: Cover:

Type P (EPDM). Black. Synthetic, high tensile textile with steel wire helix. Type D (SBR). Black with green spiral stripe.

COUPLINGS:

6, 7, 49 or 78. Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled and wrapped in polyethylene.

BRANDING:

Continuous transfer label. Example: “GATES® Shark® Water Suction/Discharge 150 PSI (1.03MPa) WP Made In U.S.A.”

SPECIAL ORDER REQUIREMENTS:

REMNANT LENGTHS:

Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 124

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Barracuda®

Water Hose

(Specification 4686AT) Nom. I.D. (In.) 1 1 1/4 1 1/2 1 1/2 2 2 2 1/2 2 1/2 3 3 4 4 6 6 6 8 10 12

(mm) 25.4 31.8 38.1 38.1 50.8 50.8 63.5 63.5 76.2 76.2 101.6 101.6 152.0 152.0 152.0 203.2 254.0 304.8

Nom. O.D. (In.) 1.33 1.61 1.86 1.86 2.36 2.36 2.96 2.96 3.54 3.54 4.54 4.54 6.68 6.68 6.68 9.00 11.27 13.27

(mm) 33.8 40.9 47.2 47.2 59.9 59.9 75.2 75.2 89.9 89.9 115.3 115.3 170.0 170.0 170.0 228.6 286.3 337.1

RECOMMENDED FOR:

TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 150 150 150 150 150 150 150 150 150 150 100 100 100 100 100 100

(MPa) 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 .69 .69 .69 .69 .69 .69

Suction (In. Hg) 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0

(mm Hg) 762 762 762 762 762 762 762 762 762 762 762 762 762 762 762 762 762 762

Min. Bend Radius (In.) 5.0 5.0 6.0 6.0 8.0 8.0 10.0 10.0 14.0 14.0 18.0 18.0 28.0 28.0 28.0 40.0 50.0 60.0

(mm) 127 127 152 152 203 203 254 254 356 356 457 457 711 711 711 1016 1270 1524

Wt. Per Ft. (Lbs.) .39 .51 .60 .60 .76 .76 1.06 1.06 1.74 1.74 2.25 2.25 3.94 3.94 3.94 8.81 15.80 18.63

(Kg) .18 .23 .27 .27 .35 .35 .48 .48 .79 .79 1.02 1.02 1.79 1.79 1.79 4.00 7.17 8.45

Stock (X) or Minimum Order Qty. 400 ft. X X 400 ft. X 400 ft. X 400 ft. X 400 ft. X 400 ft. X X 400 ft. X X X

Gates Item No. 4686-0199 4686-0203 4686-0204 4686-0237 4686-0200 4686-0235 4686-0205 4686-0250 4686-0201 4686-0236 4686-0202 4686-0208 4686-0206 4686-0207 4686-0234 4686-0209 4686-0210 4686-0211

Medium to light duty water suction/discharge for agricultural, construction and industrial applications. EPDM tube designed to handle a variety of liquids including Lasso*, Lasso II* and Freedom*. Recommended for sanitation liner in marine applications. -32°F to +200°F (-36°C to +93°C). For 8" through 12" sizes. -40°F to +180°F (-40°C to +82°C). For 1" through 6" sizes. Tube: Reinforcement: Cover:

Type P (EPDM). Black. Synthetic, high tensile textile with steel wire helix. Type P (EPDM). Black with green spiral stripe.

COUPLINGS:

5, 6, 7, 8, 49 or 78 all sizes. Reference the Hose Coupling Section.

PACKAGING:

1" through 6": Packaged with each length coiled and wrapped in polyethylene. 8" through 12": Packaged with each length placed in nylon woven fabric.

BRANDING:

Standard Pack 100 ft. 100 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft. 25 ft. 20 ft. 200 ft. 25 ft. 25 ft. 25 ft.

Continuous transfer label. Example: “GATES® Barracuda® Water Suction/Discharge 150 PSI (1.03MPa) WP Made In U.S.A.”

SPECIAL ORDER REQUIREMENTS:

Special production runs require minimum order quantities of 400 feet for sizes through 4" I.D. and 200 feet for sizes above 4" I.D. If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details.

REMNANT LENGTHS:

Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability. *Lasso®, Lasso II® and Freedom® are Registered Trademarks of Monsanto.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 125

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Steelhead®

Water Hose

(Specification 3135SP) Nom. I.D. (In.) 1 1/2 1 5/8 1 7/8 2 2 1/2 3 3 3 1/2 4 4 1/2 6

(mm) 38.1 41.3 47.6 50.8 63.5 76.2 76.2 88.9 101.6 114.3 152.4

Nom. O.D. (In.) 1.98 2.10 2.35 2.48 2.99 3.49 3.49 3.99 4.49 5.01 6.51

(mm) 50.3 53.3 59.7 63.5 76.0 88.7 88.7 101.4 114.1 127.3 165.4

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 150 150 150 150 150 150 150 150 150

(MPa) 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03

Suction (In. Hg) — — — — — — — — — — —

(mm Hg) — — — — — — — — — — —

Min. Bend Radius (In.) 12.0 15.0 15.0 20.0 25.0 36.0 36.0 42.0 48.0 54.0 72.0

(mm) 305 381 381 508 635 914 914 1067 1219 1372 1829

Wt. Per Ft. (Lbs.) .70 .74 .88 .93 1.14 1.35 1.64 1.35 1.85 2.16 2.84

(Kg) .32 .34 .40 .42 .52 .61 .74 .74 .84 .98 1.29

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 200 ft. 100 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. X 400 ft. 400 ft. X X X 400 ft. 400 ft. X X X

Gates Item No. 3135-2651 3135-2652 3135-2653 3135-2654 3135-2655 3135-2656 3135-2661 3135-2657 3135-2658 3135-2659 3135-2660

Water discharge in heavy duty industrial applications. -40°F to +150°F (-40°C to +66°C) continuous service. Tube: Reinforcement: Cover:

Type D (SBR). Black. Multiple plies of synthetic, high tensile textile. Type D (SBR). Black with green spiral stripe.

COUPLINGS:

1, 3, 5, 7, 49 or 78. Reference the Hose Coupling Section.

PACKAGING:

100' coiled and wrapped in polyethylene.

BRANDING:

Continuous transfer label. Example: “GATES® Steelhead® HD Water Discharge 150 PSI (1.03MPa) WP Made In U.S.A.”

SPECIAL ORDER REQUIREMENTS:

REMNANT LENGTHS:

Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 126

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Marlin®

Water Hose

(Specification 3137M) Nom. I.D. (In.) 1 1/2 1 1/2 2 2 2 1/2 2 1/2 3 3 3 1/2 4 4 4 5 6 6

(mm) 38.1 38.1 50.8 50.8 63.5 63.5 76.2 76.2 88.9 101.6 101.6 101.6 127.0 152.4 152.4

Nom. O.D. (In.) 1.82 1.90 2.33 2.41 2.83 2.91 3.33 3.41 3.91 4.33 4.41 4.33 5.44 6.40 6.49

(mm) 46.2 48.3 59.2 61.2 71.9 73.9 84.6 86.6 99.3 110.0 112.0 110.0 138.2 162.6 164.9

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150

(MPa) 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03

Suction (In. Hg) — — — — — — — — — — — — — — —

(mm Hg) — — — — — — — — — — — — — — —

Min. Bend Radius (In.) 12.0 12.0 20.0 20.0 25.0 25.0 36.0 36.0 42.0 48.0 48.0 48.0 60.0 72.0 72.0

(mm) 305 305 508 508 635 635 914 914 1067 1219 1219 1219 1524 1829 1829

Gates Item No. 3137-0370 3137-0371 3137-0372 3137-0373 3137-0374 3137-0375 3137-0376 3137-0377 3137-0378 3137-0379 3137-0380 3137-1272 3137-0381 3137-0382 3137-0383

Type P (EPDM). Black. Multiple plies of synthetic, high tensile textile. Type D (SBR). Black with green spiral stripe.

1, 3, 5, 7, 49 or 78. Reference the Hose Coupling Section. 100' coiled and wrapped in polyethylene.

REMNANT LENGTHS:

Stock (X) or Minimum Order Qty. X X X X 400 ft. X X X X X X 400 ft. X X X

-40°F to +180°F (-40°C to +82°C) continuous service. Tube: Reinforcement: Cover:

COUPLINGS:

SPECIAL ORDER REQUIREMENTS:

(Kg) .21 .29 .30 .38 .36 .46 .43 .55 .67 .60 .76 .60 .98 1.05 1.34

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 200 ft. 100 ft. 100 ft. 100 ft.

Water discharge in heavy duty service requiring a compact, rugged and lightweight hose.

PACKAGING: BRANDING:

Wt. Per Ft. (Lbs.) .47 .63 .65 .84 1.02 1.02 1.21 1.21 1.47 1.32 1.67 1.32 2.17 2.32 2.96

Continuous transfer label. Example: “GATES® Marlin® Water Discharge 150 PSI (1.03MPa) WP Made In U.S.A.” Special production runs require minimum order quantities of 400 feet for sizes through 4" and 200 feet for sizes above 4". If a special transfer label is required, contact Gates Corporation for minimum quantity. Specific cut lengths available through the Cut Length Program. Contact Customer Service for details. Remnant lengths are sometimes available in popular sizes at a discount. Contact Gates Corporation for pricing, order requirements and availability.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 127

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Dolphin®

Water Hose

(Specification 3137T) Nom. I.D. (In.) 1 1/4 1 1/2 1 1/2 2 2 2 1/2 3 3 4 4 6 6

(mm) 31.8 38.1 38.1 50.8 50.8 63.5 76.2 76.2 101.6 101.6 152.4 152.4

Nom. O.D. (In.) 1.53 1.78 1.78 2.32 2.32 2.82 3.36 3.36 4.36 4.36 6.38 6.38

(mm) 38.9 45.2 45.2 58.9 58.9 71.6 85.3 85.3 111.7 111.7 162.1 162.1

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 150 150 150 150 150 150 150 150 150 150 125 125

(MPa) 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 1.03 .86 .86

Suction (In. Hg) — — — — — — — — — — — —

(mm Hg) — — — — — — — — — — — —

Min. Bend Radius (In.) — — — — — — — — — — — —

(mm) — — — — — — — — — — — —

Wt. Per Ft. (Lbs.) .37 .43 .43 .65 .65 .80 1.08 1.08 1.41 1.41 2.09 2.09

(Kg) .17 .20 .20 .30 .30 .36 .49 .49 .64 .64 .95 .95

Standard Pack 100 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 100 ft. 200 ft. 100 ft. 200 ft. 100 ft. 200 ft.

Stock (X) or Minimum Order Qty. X X 400 ft. X 400 ft. X X 400 ft. X 400 ft. X 400 ft.

Gates Item No. 3137-0884 3137-0883 3137-0898 3137-0885 3137-0905 3137-0888 3137-0886 3137-0895 3137-0889 3137-0896 3137-0890 3137-0892

Medium to light duty water discharge for agricultural, construction and industrial applications. EPDM tube designed to handle a variety of liquids including Lasso*, Lasso II* and Freedom*. -40°F to +180°F (-40°C to +82°C). Tube: Reinforcement: Cover:

Type P (EPDM). Black. Synthetic, high tensile textile. Type P (EPDM). Black with green spiral stripe.

COUPLINGS:

5, 6, 7, 8, 49 or 78 all sizes. Reference the Hose Coupling Section. NOTE: 3:1 Safety Factor for Burst Pressure to Working Pressure is reduced when the temperature increases.

PACKAGING:

100' length coiled and wrapped in polyethylene.

BRANDING:

Continuous transfer label. Example: “GATES® Dolphin® Water Discharge 150 PSI (1.03MPa) WP Made In U.S.A.”

SPECIAL ORDER REQUIREMENTS:

REMNANT LENGTHS:

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 128

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Master-Flex® 500

Water Hose

(Specification 7744) Nom. I.D. (In.) 1 1/2 2 2 1/2 3 4 6 8

(mm) 38.1 50.8 63.5 76.2 101.6 152.4 203.2

Nom. O.D. (In.) 1.67 2.16 2.55 3.17 4.20 6.20 8.16

(mm) 42.4 54.9 64.8 80.5 106.7 157.5 207.3

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Max. W.P. (psi) 75 65 60 60 60 45 45

(MPa) .52 .45 .41 .41 .41 .31 .31

Suction (In. Hg) — — — — — — —

(mm Hg) — — — — — — —

Min. Bend Radius (In.) — — — — — — —

(mm) — — — — — — —

Wt. Per Ft. (Lbs.) .17 .21 .28 .39 .53 .88 1.27

(Kg) .08 .10 .13 .18 .24 .40 .58

Standard Pack 300 ft. 300 ft. 300 ft. 300 ft. 300 ft. 300 ft. 300 ft.

Stock (X) or Minimum Order Qty. X X X X X X X

Gates Item No. 7744-1001 7744-1002 7744-1003 7744-1004 7744-1005 7744-1006 7744-1007

General lay flat water discharge service. Excellent for job sites in construction, irrigation and areas where a lightweight, flexible hose is required. +25°F to +120°F (-4°C to +49°C) continuous service. Tube: Reinforcement: Cover:

Type G (PVC). Blue with yellow identification. Synthetic, high tensile textile. Type G (PVC). Blue. Smooth.

COUPLINGS:

5, 6, 7 or 49. One band for 1 1/2". Two bands for 2" I.D. and larger. Reference the Hose Coupling Section.

PACKAGING:

300' length coiled in polyethylene and banded, one length.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Ink stamp every 5 ft. with I.D. only. None. None.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 129

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Master-Flex® 100GR

Water Hose

(Specification 7744) Nom. I.D. (In.) 1 1 1/4 1 1/2 2 2 1/2 3 4 5 6

(mm) 25.4 31.8 38.1 50.8 63.5 76.2 101.6 127.0 152.4

Nom. O.D. (In.) 1.27 1.53 1.82 2.36 2.90 3.44 4.52 5.65 6.80

(mm) 32.3 38.9 46.2 59.9 73.7 87.4 114.8 143.5 172.7

Max. W.P. (psi) 90 90 90 70 65 60 50 45 45

(MPa) .62 .62 .62 .48 .45 .41 .34 .31 .31

Suction (In. Hg) 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0

(mm Hg) 711 711 711 711 711 711 711 711 711

Min. Bend Radius (In.) 3.0 4.0 5.0 6.0 8.0 9.0 13.0 21.0 24.0

(mm) 76 102 127 152 203 229 330 533 610

Wt. Per Ft. (Lbs.) .27 .36 .47 .66 .92 1.20 1.87 3.08 4.56

(Kg) .12 .16 .21 .30 .42 .54 .86 1.40 2.07

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. X X X X X X X 1,000 ft. X

Gates Item No. 7744-3101 7744-3102 7744-3103 7744-3104 7744-3105 7744-3106 7744-3107 7744-3108 7744-3109

*Working Pressure and Suction at +72°F (+22°C).

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Conveying water and light chemical solutions under suction or rated discharge pressure. -10°F to +130°F (-23°C to +55°C) continuous service. Tube: Reinforcement: Cover:

Type G (PVC). Green. Rigid thermoplastic helix. White. Type G (PVC). Green. Smooth.

COUPLINGS:

1, 6, 7, 49 or 78 all sizes. Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled and wrapped in polyethylene.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Unlabeled. Special production runs require minimum order quantities of 1,000 feet per size. No deviations allowed to above product. None.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 130

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Master-Flex® 101CL

Water Hose

(Specification 7744) Smooth Cover Nom. I.D. (In.) 1 1 1/4 1 1/2 2 2 1/2 3 4 5 6

(mm) 25.4 31.8 38.1 50.8 63.5 76.2 101.6 127.0 152.4

Nom. O.D. (In.) 1.27 1.53 1.82 2.36 2.90 3.44 4.52 5.65 6.80

(mm) 32.3 38.9 46.2 60.0 73.7 87.4 114.8 143.5 172.7

Max. W.P. (psi) 90 90 90 70 65 55 50 45 45

(MPa) .62 .62 .62 .48 .45 .38 .34 .31 .31

Suction (In. Hg) 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0

(mm Hg) 711 711 711 711 711 711 711 711 711

Min. Bend Radius (In.) 3.0 4.0 5.0 6.0 8.0 9.0 13.0 21.0 24.0

(mm Hg) 711 711 711 711 711 711 711 711

Min. Bend Radius (In.) 2.0 3.0 3.0 4.0 6.0 8.0 11.0 15.0

(mm) 76 102 127 152 203 229 330 533 610

Wt. Per Ft. (Lbs.) .27 .34 .47 .66 .92 1.20 1.87 3.00 4.42

(Kg) .12 .15 .21 .30 .42 .54 .85 1.36 2.00

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. X X X X X X X 1,000 ft. X

Gates Item No. 7744-2101 7744-2102 7744-2103 7744-2104 7744-2105 7744-2106 7744-2107 7744-2108 7744-2109

(mm) 51 76 76 102 152 203 279 381

Wt. Per Ft. (Lbs.) .14 .31 .37 .57 1.04 1.65 2.34 4.08

(Kg) .06 — .17 .26 .47 .75 1.06 1.85

Standard Pack 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft. 100 ft.

Stock (X) or Minimum Order Qty. X X X X X X 1,000 ft. X

Gates Item No. 7744-0000 7744-0015 7744-0008 7744-0009 7744-0011 7744-0012 7744-0013 7744-0014

*Working Pressure and Suction at +72°F (+22°C).

Corrugated Cover Nom. I.D. (In.) 1 1 1/4 1 1/2 2 3 4 5 6 *Working

Nom. Max. O.D. W.P. (mm) (In.) (mm) (psi) (MPa) 25.4 1.26 32.0 35 .24 31.8 1.61 40.9 50 .34 38.1 1.86 47.2 50 .34 50.8 2.44 62.0 40 .28 76.2 3.54 89.9 35 .24 101.6 4.65 118.1 35 .24 127.0 5.73 145.5 30 .21 152.4 6.98 177.3 35 .24 Pressure and Suction at +72°F (+22°C).

RECOMMENDED FOR: TEMPERATURE: CONSTRUCTION:

Suction (In. Hg) 28.0 28.0 28.0 28.0 28.0 28.0 28.0 28.0

Conveying water and light chemical solutions where a clear PVC hose with a white helix is desirable for heavy duty applications. -10°F to +130°F (-23°C to +55°C) continuous service. Tube: Reinforcement:

Type G (PVC). Clear. Smooth. Rigid thermoplastic helix.

COUPLINGS:

1, 6, 7, 49 or 78 all sizes. Reference the Hose Coupling Section.

PACKAGING:

All lengths coiled and wrapped in polyethylene.

BRANDING: SPECIAL ORDER REQUIREMENTS: REMNANT LENGTHS:

Unlabeled. Special production runs require minimum order quantities of 1,000 feet per size. No deviations allowed to above product. None.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 131

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

GATES GC®96 INDUSTRIAL HOSE CRIMPER The GC®96 crimper is capable of crimping up to 6 inch ID industrial hose. This crimper allows distributors to make assemblies that are reliable and professional looking, thus providing more value to the end user. The large crimper head allows industrial hose assemblies to be made with a variety of terminations using crimpable ferrules and sleeves. The GC96 crimper has additional versatility since in conjunction with optional spacer dies and GC ®32–XD dies; it can make Gates hydraulic hose assemblies also.

Features: • • • • • • •

Electronic touch screen control panel for fast input of crimper settings Horizontal front-end feed makes crimping easier and convenient 340 ton force that allows crimping of a wide variety of couplings 2 speed die closure and rapid retract permit fast assembly fabrication 3-phase inverter allows crimper to be used all over the world Full range of die sets that enable production of a wide range of hose assemblies Complete line of options permit customizing the crimper to meet your needs

Model Number: GC96

Product Number: 7480-9001

Crimping Force: 340 Tons

Capability: 1/4" – 2": Industrial and hydraulic hose (except 2", 6-wire) 2-1/2" – 4": Industrial hose 5" – 6": Industrial hose up to and including 100 PSI WP

Power Source: 208-264 Volts, 45-65 HZ, 1 or 3 Phase and 20 Amps Electrical inverter for world-wide use

Crimper Dimensions: 31" H x 32" W x 16" D

Weight: 650 lbs.

Crimper GC96 Crimper – Includes Starter Kit, Foot Pedal, 96-610 Die Set and Lifting Rope

Product No. 7480-9001

Weight (lbs) 650

Dies and Accessories Quick Change Tool Standard Die Kit includes GC32 QCT and GC96 Spacer Dies Mirror Starter Kit Calibration Ring Knuckles GC96 Spacer Dies with box Die Set — 96-610 with box Die Set — 96-611 with box Die Set — 96-612 with box Die Set — 96-613 with box Die Set — 96-614 with box

Product No. 7482-7104 7482-9104 7482-9109 7482-9112 7482-9200 7482-9601 7482-9600 7482-9610 7482-9611 7482-9612 7482-9613 7482-9614

Weight (lbs) 2 36 10 10 2 5 31 47 41 40 46 31

For Pricing of Crimper and Accessories, please contact your local Gates Field Representative. NOTE: For replacement parts, see GC96 Operating Manual. GC32 dies should be ordered from the Hydraulic Price Sheet #35096-00.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 132

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Stainless Steel Clamps

Clamps

(Specification 7408) Clamp Size 8 10 12 16 20 24 28 32 36 48 52 56 60 64 72 104

Hose Range Min. .3125 .375 .625 .75 1 1.25 1.25 1.5 1.75 2.5 3 2 2.25 2.25 3 4

RECOMMENDED FOR: CONSTRUCTION: PACKAGING:

Clamp Range Max. .5 .625 .75 1 1.25 1.5 1.75 2 2.25 3 3.25 3.5 3.75 4 4.5 6.5

Min. 7/16 1/2 1/2 3/4 3/4 1 1 5/16 1 1/16 1 7/8 1 5/8 1 7/8 2 1/8 2 5/16 2 5/8 3 1/2 4

Max. 1 1 1/8 1 1/4 1 1/2 1 3/4 2 2 1/4 2 1/2 2 3/4 3 1/2 3 3/4 4 4 1/4 4 1/2 5 7

Standard Pack 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea.

Stock (X) or Minimum Order Qty. X X X X X X X X X X X X X X X X

Gates Item No. 7408-1008 7408-1010 7408-1012 7408-1016 7408-1020 7408-1024 7408-1028 7408-1032 7408-1036 7408-1048 7408-1052 7408-1056 7408-1060 7408-1064 7408-1072 7408-1104

Clamping all types of hose and tubing in corrosive marine environment. Clamps are constructed of 100% marine grade stainless steel. Bands are 9/16" wide with rounded edges to prevent cutting. Screws feature 305 grade stainless steel construction and deep slotted hex heads. 10 each per box.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The worldâ&#x20AC;&#x2122;s most trusted name in belts, hose and hydraulics. 133

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Heavy-Duty T-Bolt Clamps

Clamps

(Specification 7422) SAE Size 8 10 12 28 32 36 40 44 48 52 56 60 64 68 72 76 80 84 88 92 100 108 116 124 132 140 148 156 164 172 180 188 196 204 212 220 228 236 244

Min. Dia. (In.) 1.375 1.5 1.625 1.75 1.875 2 2.125 2.25 2.375 2.5 2.625 2.75 2.875 3 3.125 3.25 3.375 3.5 3.625 3.75 4 4.25 4.5 4.75 5 5.25 5.5 5.75 6 6.25 6.5 6.75 7 7.25 7.5 7.75 8 8.25 8.5

RECOMMENDED FOR: CONSTRUCTION:

PACKAGING:

mm 35.1 38.1 41.4 44.5 47.8 50.8 54.1 57.2 60.5 63.5 66.8 69.9 73.2 76.2 79.5 82.6 85.9 88.9 92.2 95.3 101.6 108 114.3 120.7 127 133.4 139.7 146.1 152.4 158.8 165.1 171.5 177.8 184.2 190.5 196.9 203.2 209.6 215.9

Max. Dia. (In.) 1.5625 1.625 1.875 2 2.1875 2.3125 2.4375 2.5625 2.6875 2.8125 2.9375 3.0625 3.1875 3.3125 3.4375 3.5625 3.6875 3.8125 3.9375 4.0625 4.3125 4.5625 4.8125 5.0625 5.3125 5.5625 5.8125 6.0625 6.3125 6.5625 6.8125 7.0625 7.3125 7.5625 7.8125 8.0625 8.3125 8.5625 8.8125

mm 38.6 41.7 46 50.8 55.6 58.7 62 65 68.3 71.4 74.7 77.7 81 84.1 87.4 90.4 93.7 96.8 100.1 103.1 109.5 115.8 122.2 128.5 134.9 141.2 147.6 153.9 160.3 166.6 173 179.3 185.7 192 198.4 204.7 211.1 217.4 223.8

Recommended Installation Torque 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm) 75 in./lbs. (8.5 Nm)

Standard Pack 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea. 10 ea.

Stock (X) or Minimum Order Qty. X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X

Gates Item No. 7422-1049 7422-1050 7422-1051 7422-1052 7422-1053 7422-1054 7422-1055 7422-1056 7422-1057 7422-1058 7422-1059 7422-1060 7422-1061 7422-1062 7422-1063 7422-1064 7422-1065 7422-1066 7422-1067 7422-1068 7422-1069 7422-1070 7422-1071 7422-1072 7422-1073 7422-1074 7422-1075 7422-1076 7422-1077 7422-1078 7422-1079 7422-1080 7422-1081 7422-1082 7422-1083 7422-1084 7422-1085 7422-1086 7422-1087

Use in high vibration and large diameter applications. Typical applications include industrial machinery, truck air take systems, cold side charge air systems and off road equipment. T-Bolt Standard Design Band/Bridge: 3/4" width, 201/301 stainless steel. Bolt: 1/4" - 28 plated steel. Nut: 7/16" hex, nylon insert, plated steel locknut. Trunnion: Plated Steel 10 each per box.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 134

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Hose Couplings GLX® - Male Pipe (NPTF 30° Cone Seat)

Standard Pack Size (In.) 1/4 1/4 3/8 3/8 1/2 1/2 5/8 3/4 3/4 1 1 1/4 1/2

Stem Hex (In.) 1/2 9/16 11/16 11/16 13/16 7/8 15/16 1 1/16 1 1/16 1 3/8 1 3/4 13/16

Thread (In.) 1/8-27 1/4-18 1/4-18 3/8-18 3/8-18 1/2-14 1/2-14 1/2-14 3/4-14 1-11 1/2 1 1/4-11 1/2 3/4-14

Description 4GLX-2MP 4GLX-4MP 6GLX-4MP 6GLX-6MP 8GLX-6MP 8GLX-8MP 10GLX-8MP 12GLX-8MP 12GLX-12MP 16GLX-16MP 20GLX-20MP 8GLX-12MP

Nut Hex (In.) — — — — — — — — — — — —

Overall Length (In.) (mm) 2.01 51.1 2.17 55.1 2.32 58.9 2.32 58.9 2.72 69.1 2.78 70.6 2.40 61.0 3.46 87.9 3.46 87.9 4.11 104.4 4.41 112.0 3.46 87.8

Cut Off Length (In.) (mm) .98 24.9 1.14 29.0 1.22 31.0 1.22 31.0 1.24 31.5 1.40 35.6 1.55 39.3 1.46 37.1 1.46 37.1 1.88 47.8 2.09 53.0 1.45 36.9

Weight Per Ea. (Lbs.) .09 .11 .15 .16 .25 .29 .22 .45 .49 .78 1.24 .15

Standard Pack 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea.

Stock (X) or Minimum Order Qty. 50 ea. X 50 ea. X 50 ea. X X 50 ea. X X X X

Gates Item No. 7107-00105 7107-00115 7107-00135 7107-00145 7107-00165 7107-00175 7107-00195 7107-00215 7107-00225 7107-00255 7107-00265 7107-00785

Bulk Pack Size (In.) 1/4 1/4 3/8 3/8 1/2 1/2 5/8 3/4 3/4 1 1 1/4 1/2

Description 4GLX-2MPXBULK 4GLX-4MPXBULK 6GLX-4MPXBULK 6GLX-6MPXBULK 8GLX-6MPXBULK 8GLX-8MPXBULK 10GLX-8MPXBULK 12GLX-8MPXBULK 12GLX-12MPXBULK 16GLX-16MPXBULK 20GLX-20MPXBULK 8GLX-12MPXBULK

Stem Hex (In.) 1/2 9/16 11/16 11/16 13/16 7/8 15/16 1 1/16 1 1/16 1 3/8 1 3/4 13/16

Thread (In.) 1/8-27 1/4-18 1/4-18 3/8-18 3/8-18 1/2-14 1/2-14 1/2-14 3/4-14 1-11 1/2 1 1/4-11 1/2 3/4-14

Nut Hex (In.) — — — — — — — — — — — —

Overall Length (In.) (mm) 2.01 51.1 2.17 55.1 2.32 58.9 2.32 58.9 2.72 69.1 2.78 70.6 2.40 61.0 3.46 87.9 3.46 87.9 4.11 104.4 4.41 112.0 3.46 87.8

Cut Off Length (In.) (mm) .98 24.9 1.14 29.0 1.22 31.0 1.22 31.0 1.24 31.5 1.40 35.6 1.55 39.3 1.46 37.1 1.46 37.1 1.88 47.8 2.09 53.0 1.45 36.9

Weight Per Ea. (Lbs.) .09 .11 .15 .16 .25 .29 .22 .46 .49 .78 1.24 .15

Standard Pack 200 ea. 200 ea. 150 ea. 150 ea. 100 ea. 100 ea. 100 ea. 75 ea. 75 ea. 25 ea. 20 ea. 60 ea.

Stock (X) or Minimum Order Qty. 200 ea. X 150 ea. X 100 ea. X X 75 ea. X X X 60 ea.

Gates Item No. 7107-0010 7107-0011 7107-0013 7107-0014 7107-0016 7107-0017 7107-0019 7107-0021 7107-0022 7107-0025 7107-0026 7107-0078

GLX® - MS 45° SAE Male Solid

Standard Pack Size (In.) 1/4 3/8 1/2 3/4

Description 4GLX-4MS 6GLX-6MS 8GLX-8MS 12GLX-12MS

Thread (In.) 7/16-20 5/8-18 3/4-16 1 1/16-14

Stem Hex (In.) 1/2 5/8 13/16 1 1/16

Nut Hex (In.) — — — —

Overall Length (In.) (mm) 2.11 53.6 2.38 60.5 2.89 73.4 3.78 96.0

Cut Off Length (In.) (mm) 1.08 27.4 1.28 32.5 1.42 36.1 1.77 45.0

Weight Per Ea. (Lbs.) .09 .16 .27 .54

Standard Pack 1 ea. 1 ea. 1 ea. 1 ea.

Stock (X) or Minimum Order Qty. 50 ea. 50 ea. 50 ea. 50 ea.

Gates Item No. 7107-00525 7107-00535 7107-00545 7107-00555

Bulk Pack Size (In.) 1/4 3/8 1/2 3/4

Description 4GLX-4MSXBULK 6GLX-6MSXBULK 8GLX-8MSXBULK 12GLX-12MSXBULK

Thread (In.) 7/16-20 5/8-18 3/4-16 1 1/16-14

Stem Hex (In.) 1/2 5/8 13/16 1 1/16

Nut Hex (In.) — — — —

Overall Length (In.) (mm) 2.11 53.6 2.38 60.5 2.89 73.4 3.78 96.0

Cut Off Length (In.) (mm) 1.08 27.4 1.28 32.5 1.42 36.1 1.77 45.0

Weight Per Ea. (Lbs.) .09 .16 .27 .54

Standard Pack 1 ea. 1 ea. 1 ea. 1 ea.

Stock (X) or Minimum Order Qty. 50 ea. 50 ea. 50 ea. 50 ea.

Gates Item No. 7107-0052 7107-0053 7107-0054 7107-0055

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 135

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Hose Couplings GLX® - FSX 45° SAE Female Swivel

Standard Pack Size (In.) 1/4 3/8 1/2 3/4

Description 4GLX-4FSX 6GLX-6FSX 8GLX-8FSX 12GLX-12FSX

Thread (In.) 7/16-20 5/8-18 3/4-16 1 1/16-14

Stem Hex (In.) 1/2 5/8 13/16 1 1/16

Nut Hex (In.) — — — —

Overall Length (In.) (mm) 2.24 56.9 2.44 62.0 2.82 71.6 3.68 93.5

Cut Off Length (In.) (mm) 1.22 31.0 1.35 34.3 1.34 34.0 1.67 42.4

Weight Per Ea. (Lbs.) .13 .17 .26 .51

Standard Pack 200 ea. 150 ea. 100 ea. 75 ea.

Stock (X) or Minimum Order Qty. 200 ea. 150 ea. 100 ea. 75 ea.

Gates Item No. 7107-00485 7107-00495 7107-00505 7107-00515

Bulk Pack Size (In.) 1/4 3/8 1/2 3/4

Description 4GLX-4FSXXBULK 6GLX-6FSX XBULK 8GLX-8FSX XBULK 12GLX-12FSX XBULK

Stem Hex (In.) 1/2 5/8 13/16 1 1/16

Thread (In.) 7/16-20 5/8-18 3/4-16 1 1/16-14

Nut Hex (In.) — — — —

Overall Length (In.) (mm) 2.24 56.9 2.44 62.0 2.82 71.6 3.68 93.5

Cut Off Length (In.) (mm) 1.22 31.0 1.35 34.3 1.34 34.0 1.67 42.4

Weight Per Ea. (Lbs.) .13 .17 .26 .51

Standard Pack 1 ea. 1 ea. 1 ea. 1 ea.

Stock (X) or Minimum Order Qty. 50 ea. 50 ea. 50 ea. 50 ea.

Gates Item No. 7107-0048 7107-0049 7107-0050 7107-0051

GLX® - MPX Male NPTF Swivel

Standard Pack Size (In.) 1/4 3/8 1/2 3/4 1 1 1/4

Description 4GLX-4MPX 6GLX-6MPX 8GLX-8MPX 12GLX-12MPX 16GLX-16MPX 20GLX-20MPX

Thread (In.) 1/4-18 3/8-18 1/2-14 3/4-14 1-11 1/2 1 1/4-11 1/2

Stem Hex (In.) 1/2 5/8 13/16 1 1/16 1 3/8 1 7/8

Nut Hex (In.) 11/16 7/8 1 1 5/16 1 5/8 2

Overall Length (In.) (mm) 2.61 66.3 2.81 71.4 3.42 86.9 4.02 102.0 4.73 120.1 5.30 134.6

Cut Off Length (In.) (mm) 1.58 40.1 1.72 43.7 1.95 49.5 2.01 51.1 2.50 63.5 2.98 75.7

Weight Per Ea. (Lbs.) .15 .25 .36 .65 .98 1.83

Standard Pack 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea.

Stock (X) or Minimum Order Qty. 50 ea. 50 ea. 50 ea. 50 ea. 50 ea. 50 ea.

Gates Item No. 7107-00565 7107-00575 7107-00585 7107-00595 7107-00605 7107-00615

Bulk Pack Size (In.) 1/4 3/8 1/2 3/4 1 1 1/4

Description 4GLX-4MPX XBULK 6GLX-6MPX XBULK 8GLX-8MPX XBULK 12GLX-12MPX XBULK 16GLX-16MPX XBULK 20GLX-20MPX XBULK

Thread (In.) 1/4-18 3/8-18 1/2-14 3/4-14 1-11 1/2 1 1/4-11 1/2

Stem Hex (In.) 1/2 5/8 13/16 1 1/16 1 3/8 1 7/8

Nut Hex (In.) 11/16 7/8 1 1 5/16 1 5/8 2

Overall Length (In.) (mm) 2.61 66.3 2.81 71.4 3.42 86.9 4.02 102.0 4.73 120.1 5.30 134.6

Cut Off Length (In.) (mm) 1.58 40.1 1.72 43.7 1.95 49.5 2.01 51.1 2.50 63.5 2.98 75.7

Weight Per Ea. (Lbs.) .15 .25 .36 .65 1.14 1.83

Standard Pack 200 ea. 150 ea. 100 ea. 75 ea. 25 ea. 20 ea.

Stock (X) or Minimum Order Qty. 200 ea. 150 ea. 100 ea. 75 ea. 25 ea. 20 ea.

Gates Item No. 7107-0056 7107-0057 7107-0058 7107-0059 7107-0060 7107-0061

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 136

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Hose Couplings GLX® - FP Female NPTF Swivel

Standard Pack Size (In.) 1/4 3/8 3/8 1/2 1/2 3/4 1

Description 4GLX-4FP 6GLX-4FP 6GLX-6FP 8GLX-6FP 8GLX-8FP 12GLX-12FL 16GLX-16FP

Thread (In.) 1/4-18 1/4-18 3/8-18 3/8-18 1/2-14 3/4-14 1-11 1/2

Stem Hex (In.) 11/16 11/16 13/16 13/16 1 1 1/4 1 1/2

Nut Hex (In.) — — — — — — —

Overall Length (In.) (mm) 1.99 50.5 2.07 52.6 2.07 52.6 2.48 63.0 2.64 67.1 3.23 82.0 3.86 98.0

Cut Off Length (In.) (mm) .96 24.4 .97 24.6 .97 24.6 1.00 25.4 1.16 29.5 1.22 31.0 1.62 41.1

Weight Per Ea. (Lbs.) .11 .16 .18 .25 .28 .48 .76

Standard Pack 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea.

Stock (X) or Minimum Order Qty. 50 ea. 50 ea. 50 ea. 50 ea. 50 ea. 50 ea. 50 ea.

Gates Item No. 7107-00415 7107-00425 7107-00435 7107-00445 7107-00455 7107-00465 7107-00475

Bulk Pack Size (In.) 1/4 3/8 3/8 1/2 1/2 3/4 1

Thread (In.) 1/4-18 1/4-18 3/8-18 3/8-18 1/2-14 3/4-14 1-11 1/2

Description 4GLX-4FPXBULK 6FLX-4FPXBULK 6GLX-6FPXBULK 8GLX-6FPXBULK 8GLX-8FPXBULK 12GLX-12FPXBULK 16GLX-16FPXBULK

Stem Hex (In.) 11/16 11/16 13/16 13/16 1 1 1/4 1 1/2

Nut Hex (In.) — — — — — — —

Overall Length (In.) (mm) 1.99 50.5 2.07 52.6 2.07 52.6 2.48 63.0 2.64 67.1 3.23 82.0 3.86 98.0

Cut Off Length (In.) (mm) .96 24.4 .97 24.6 .97 24.6 1.00 25.4 1.16 29.5 1.22 31.0 1.62 41.1

Weight Per Ea. (Lbs.) .12 .16 .18 .25 .28 .48 .76

Standard Pack 200 ea. 150 ea. 150 ea. 100 ea. 100 ea. 75 ea. 25 ea.

Stock (X) or Minimum Order Qty. 200 ea. 150 ea. 150 ea. 100 ea. 100 ea. 75 ea. 25 ea.

Gates Item No. 7107-0041 7107-0042 7107-0043 7107-0044 7107-0045 7107-0046 7107-0047

GLX® - FPX Female NPSM Swivel

Standard Pack Size (In.) 1/4 3/8 3/8 1/2 1/2 3/4 1

Description 4GLX-4FPX 6GLX-4FPX 6GLX-6FPX 8GLX-6FPX 8GLX-8FPX 12GLX-12FPX 16GLX-16FPX

Thread (In.) 1/4-18 1/4-18 3/8-18 3/8-18 1/2-14 3/4-14 1-11 1/2

Stem Hex (In.) 1/2 5/8 5/8 13/16 13/16 1 1/16 1 3/8

Nut Hex (In.) 11/16 11/16 7/8 7/8 1 1 1/4 1 1/2

Overall Length (In.) (mm) 2.24 56.9 2.40 61.0 2.49 63.2 2.85 72.4 2.89 73.4 3.72 94.5 4.11 104.4

Cut Off Length (In.) (mm) 1.22 31.0 1.30 33.0 1.39 35.3 1.38 35.1 1.41 35.8 1.71 43.4 1.87 47.5

Weight Per Ea. (Lbs.) .12 .18 .21 .30 .32 .57 .98

Standard Pack 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea.

Stock (X) or Minimum Order Qty. 50 ea. 50 ea. 50 ea. 50 ea. 50 ea. 50 ea. 50 ea.

Gates Item No. 7107-00345 7107-00355 7107-00365 7107-00375 7107-00385 7107-00395 7107-00405

Bulk Pack Size (In.) 1/4 3/8 3/8 1/2 1/2 3/4 1

Description 4GLX-4FPXXBULK 6FLX-4FPX XBULK 6GLX-6FPX XBULK 8GLX-6FPX XBULK 8GLX-8FPX XBULK 12GLX-12FPX XBULK 16GLX-16FPX XBULK

Thread (In.) 1/4-18 1/4-18 3/8-18 3/8-18 1/2-14 3/4-14 1-11 1/2

Stem Hex (In.) 1/2 5/8 5/8 13/16 13/16 1 1/16 1 3/8

Nut Hex (In.) 11/16 11/16 7/8 7/8 1 1 1/4 1 1/2

Overall Length (In.) (mm) 2.24 56.9 2.40 61.0 2.49 63.2 2.85 72.4 2.89 73.4 3.72 94.5 4.11 104.4

Cut Off Length (In.) (mm) 1.22 31.0 1.30 33.0 1.39 35.3 1.38 35.1 1.41 35.8 1.71 43.4 1.87 47.5

Weight Per Ea. (Lbs.) .12 .18 .21 .30 .32 .57 .98

Standard Pack 200 ea. 150 ea. 150 ea. 100 ea. 100 ea. 75 ea. 25 ea.

Stock (X) or Minimum Order Qty. 200 ea. 150 ea. 150 ea. 100 ea. 100 ea. 75 ea. 25 ea.

Gates Item No. 7107-0034 7107-0035 7107-0036 7107-0037 7107-0038 7107-0039 7107-0040

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 137

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Hose Couplings GLX® - Female JIC 37° Flare Swivel

Standard Pack Size (In.) 1/4 3/8 1/2 5/8 3/4 1 1 1/4

Description 4GLX-4FJX 6GLX-6FJX 8GLX-8FJX 10GLX-10FJX 12GLX-12FJX 16GLX-16FJX 20GLX20FJX

Thread (In.) 7/16-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 5/16-1/2 1 5/8-12

Stem Hex (In.) 1/2 5/8 13/16 — 1 1/16 1 3/8 1 3/4

Nut Hex (In.) 9/16 3/4 7/8 1 1/16 1 1/4 1 1/2 2

Overall Length (In.) (mm) 2.10 53.3 2.31 58.7 2.82 71.6 2.27 57.7 3.68 93.5 4.17 105.9 4.58 116.4

Cut Off Length (In.) (mm) 1.08 27.4 1.19 30.2 1.34 34.0 1.42 36.0 1.67 42.4 1.94 49.3 2.26 57.4

Weight Per Ea. (Lbs.) .11 .19 .34 .24 .63 1.08 1.32

Standard Pack 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea.

Stock (X) or Minimum Order Qty. X X X X X X X

Gates Item No. 7107-00275 7107-00285 7107-00295 7107-00305 7107-00315 7107-00325 7107-00335

Bulk Pack Size (In.) 1/4 3/8 1/2 5/8 3/4 1 1 1/4

Description 4GLX-4FJXXBULK 6GLX-6FJX XBULK 8GLX-8FJX XBULK 10GLX-10FJX XBULK 12GLX-12FJX XBULK 16GLX-16FJX XBULK 20GLX-20FJX XBULK

Stem Hex (In.) 1/2 5/8 13/16 — 1 1/16 1 3/8 1 3/4

Thread (In.) 7/16-20 9/16-18 3/4-16 7/8-14 1 1/16-12 1 5/16-1/2 1 5/8-12

Nut Hex (In.) 9/16 3/4 7/8 1 1/16 1 1/4 1 1/2 2

Overall Length (In.) (mm) 2.10 53.3 2.31 58.7 2.82 71.6 2.27 57.7 3.68 93.5 4.17 105.9 4.58 116.4

Cut Off Length (In.) (mm) 1.08 27.4 1.19 30.2 1.34 34.0 1.42 36.0 1.67 42.4 1.94 49.3 2.26 57.4

Weight Per Ea. (Lbs.) .11 .19 .34 .24 .63 1.08 1.32

Standard Pack 200 ea. 150 ea. 100 ea. 100 ea. 75 ea. 25 ea. 20 ea.

Stock (X) or Minimum Order Qty. X X X X X X X

Gates Item No. 7107-0027 7107-0028 7107-0029 7107-0030 7107-0031 7107-0032 7107-0033

GSH™ - GSH with Intergral 2″ Fig. 1502 Hammer Unions

2″ Figure 1502 Female Sub with Seal Size (In.) 1 1/2 2

Thread (In.) — —

Description 24GSH-32FHU 32GSH-32FHU

Stem Hex (In.) — —

Nut Hex (In.) — —

Overall Length (In.) (mm) 2.52 64.0 2.64 67.1

Cut Off Length (In.) (mm) 6.26 159.0 7.13 181.1

Weight Per Ea. (Lbs.) 5.49 7.45

Stock (X) or Minimum Order Qty. X X

Gates Item No. 7341-02675 7341-15695

Stock (X) or Minimum Order Qty. X X

Gates Item No. 7341-02695 7341-15715

Standard Pack 1 ea. 1 ea.

Stock (X) or Minimum Order Qty. X X

Gates Item No. 7341-02685 7341-15705

Standard Pack 1 ea. 1 ea.

Stock (X) or Minimum Order Qty. X X

Gates Item No. 7253-01905 7253-01915

Standard Pack 1 ea. 1 ea.

2″ Figure 1502 Male Sub with Nut Size (In.) 1 1/2 2

Description 24-GSH-32MHUWN 32GSH-32MHUWN

Stem Hex (In.) — —

Thread (In.) — —

Nut Hex (In.) — —

Overall Length (In.) (mm) 6.64 168.7 7.25 184.2

Cut Off Length (In.) (mm) 2.90 73.7 2.76 70.1

Weight Per Ea. (Lbs.) 16.43 17.75

Standard Pack 1 ea. 1 ea.

2″ Figure 1502 Male Sub without Nut Size (In.) 1 1/2 2

Description 24GSH-32MHU 32GSH-32MHU

Thread (In.) — —

Stem Hex (In.) — —

Nut Hex (In.) — —

Overall Length (In.) (mm) 6.64 168.7 7.25 184.2

Cut Off Length (In.) (mm) 2.90 73.7 2.76 70.1

Weight Per Ea. (Lbs.) 2.75 7.64

2″ Figure 1502 Rubber Lip Seal and Wing Nut Size (In.) 2 2

Description -32 SR -32 WN

Thread (In.) — —

Stem Hex (In.) — —

Nut Hex (In.) — —

Overall Length (In.) (mm) — — — —

Cut Off Length (In.) (mm) — — — —

Weight Per Ea. (Lbs.) .05 9.20

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 138

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Hose Couplings 2″ Butt Weld Size (In.) 2 2 2 2

Description 32GSH-32XXSBW 32GSH-40S160BW 32GSH-32S160BW 32GSH-48XXSBWXBULK

Thread (In.) — — — —

Stem Hex (In.) — — — —

Nut Hex (In.) — — — —

Overall Length (In.) (mm) 6.68 169.7 6.65 168.9 6.68 169.7 6.61 167.9

Cut Off Length (In.) (mm) 2.19 55.6 2.16 54.9 2.19 55.6 2.13 54.1

Weight Per Ea. (Lbs.) 5.14 5.51 5.16 5.82

Standard Pack 1 ea. 1 ea. 1 ea. 1 ea.

Stock (X) or Minimum Order Qty. X X X X

Gates Item No. 7341-15775 7341-15785 7341-15795 7341-15805

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 139

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products How To Use The Coupling Section NOTE: Because the hose/coupling interface is critical to hose assembly performance, always follow the specific instructions of hose and coupling manufacturers regarding the match of hose/fittings and assembly procedures. Trained personnel using proper tools and procedures should make hose assemblies. Failure to follow hose and couplings manufacturers’ instructions or failure to use trained personnel might be dangerous and could result in damage to property and serious bodily injury. Couplings are designated by Numbers, and are described as to construction and source. Adapters and fittings are available for special applications. Each coupling has a pressure rating of Low, Medium or High. These terms have a general meaning as follows: Low Pressure.......................................................... 100 psi maximum Medium Pressure................................................... 315 psi maximum High Pressure......................................................... 800 psi maximum

Coupling ratings apply only where the recommended clamps or bands are used. Use this information as a guide since different tube stocks affect coupling retention. Common shank couplings or nipples with bands or clamps should be used only on straight or plain end water or material handling hoses up to the following rated working pressures: 1/2"- l-1/2"I.D. — 315 psi 2 -3" I.D. — 100 psi 4" I.D. — 75 psi

5" I.D. — 60 psi 6" I.D. — 50 psi

NOTE: Band-It® Swaged Hose Nipples, a form of combination nipple, can be used for higher rated working pressures. They are available in plated and unplated steel plus stainless steel with Tapered Pipe Thread for 1/2"through 6" I.D. hose.

Listed are all of the clamps, bands and ferrules used to secure the couplings to the hose. The proper clamp size should be selected carefully, since many clamps will fit only one hose size or a narrow range of sizes. For certain critical fluids, specific couplings are used, as follows:

Critical Applications 1. Use only the couplings recommended in this catalog for conveying: Steam LP Gas Corrosive Chemicals Petroleum Products 2. For conveying flammable fluids, use couplings made of nonsparking materials, such as brass or aluminum. 3. For ground fueling of aircraft, use certified coupled assemblies only. When you have selected a hose from the Hose Section, you will have found one or more coupling recommendations for that hose. The following procedure will help you make the final selection:

A. If more than one coupling is recommended, make a final selection for type of coupling on basis of cost, sizes available, thread type available and application. B. Determine how the coupling is to be fastened to the hose—ferrule, band or clamp.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 140

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Coupling Installation Before making any hose assembly, check these general instructions and precautions: 1. Square Ends—Before attaching a coupling to the hose, make sure the end is cut square. This will help prevent leakage of the coupling. 2. Proper Fit of Ferrules and Clamps—This is important. Make sure you are using the correct sizes for the hose being coupled. Never buff the cover, except when specified for certain hydraulic hose couplings, and you should not enlarge the hose tube in any way to make the coupling insert fit. Occasionally, a nipple pusher tool will be helpful in pushing the insert into the hose. 3. Installation Lubricants—Use of lubricants on coupling inserts and ferrules will simplify coupling installation and reduce possibility of damage to the hose. Some lubricants to use are water, soap solution or Lactol. Or, you can use a solution of glycerin and alcohol made up of one (1) part glycerin and 15 parts wood alcohol by volume. 4. Appearance of the Hose Assembly—A properly installed coupling significantly improves customer acceptance of the product. It also provides added assurance of satisfactory service and safety of assembly. 5. Seal the Ends—Where the hose is intended for use in petroleum transfer applications and hose ends will be exposed after couplings are attached, apply a sufficient amount of quality Neoprene cement or shellac to seal the ends. 6. Critical Applications. (a) Use only the couplings recommended in this Hose Coupling Section for conveying: • Steam • Petroleum Products • LP Gas • Edible Products • Corrosive Chemicals (b) For conveying flammable fluids, use couplings made of nonsparking materials; i.e., brass or aluminum. (c) For aircraft ground fueling hose, use factory coupled assemblies only.

NOTE: Refer to NAHAD Industrial Hose Assembly Guidelines for installation information and additional general information.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 141

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Pipe Thread Usage There are several terms or abbreviations which have come into common use for denoting pipe threads. Some of these are: Iron Pipe Threads IPT Tapered IPT Straight IPT IP—S IP—T These may be satisfactory for general reference, but since there are several types of pipe thread, it is best to use the notations as given by a recognized standard (ANSI B2.1). The types in this standard which are used with industrial hose couplings are listed later in this section. Compatibility of threads and method of sealing determine which type of thread is to be used. An NPT male and female form a pressure-tight joint, and usually some type of sealing compound is placed on the threads. NPTF threads are similar in that the seal is made by tight fit between the threads. However the fit is close enough that a sealing compound is not needed. NPSM threads are used for either male or female fittings, but the seal is formed by compressing a packing or by metal contact between chamfers on the male and female. Size range is from 1/4" through 6" nominal pipe I.D. NPSH threads are similar to NPSM threads but are used mostly for fire hose or special couplings. Size range is from 1/2" through 2" nominal pipe I.D. The seal is made by compressing packing. GHT, garden hose threads, are a form of NPSH threads used on water hose. There is only one basic size of thread, 3/4 – 11-1/2. It is not compatible with 3/4-14NPT, NPSH or NPSM threads.

Couplings which come in sets usually have a female with NPSM threads and washer; and a male with NPT or NPSM threads. Long shank couplings and pin lug couplings are examples where the male has NPSM threads. Reusable petroleum couplings are examples of sets in which the male has NPT threads. Standard brass inserts have NPTF males and solid females and NPSM swivel females. The seal is made by contact of chamfers or tight fit of threads. (See Chart No.1). Couplings for hydraulic hose have threads which may conform to the above descriptions. In addition, there are many other types peculiar to the hydraulic field. For a complete description of threads, identification, sizes, methods of sealing and other related data, see Hydraulic Hose Catalog #35093. Combinations of Pipe Threads that Are Compatible: Female Male NPT (Thread Seal)

NPT NPTF

NPTF (Thread Seal)

NPTF (Dryseal) NPT

NPSM (Washer Seal)

NPT NPTF NPSM

NPSM (Mechanical Seal)

NPT NPTF

NPSH (Washer Seal)

NPSH NPT

GHT (Washer Seal)

GHT

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 142

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Nominal Pipe Size (ln.) 1/8 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 3-1/2 4 5 6

* **

Pipe O.D. (ln.) .405 .504 .675 .840 1.050 1.315 1.660 1.900 2.375 2.875 3.500 4.000 4.500 5.563 6.625

Threads Per Inch 27 18 18 14 14 11-1/2 11-1/2 11-1/2 11-1/2 8 8 8 8 8 8

NPT & NPTF *Ext. Thrd. Pitch (A) Diameter 0.36351 0.47739 0.61201 0.75843 0.96768 1.21363 1.55713 1.79609 2.26902 2.71593 3.34062 3.83750 4.33438 5.39073 6.44609

NPT *Int. Thrd. Pitch (B) Diameter 0.37476 0.48989 0.62701 0.77843 0.98887 1.23863 1.58338 1.82234 2.29627 2.76216 3.38850 3.88881 4.38712 5.44929 6.50597

NPSM** Ext. Thrd. Max. Major Diameter 0.409 0.541 0.678 0.844 1.054 1.318 1.663 1.902 2.376 2.877 3.503 4.003 4.502 5.564 6.620

Int. Thrd. Min. Minor Diameter 0.362 0.470 0.607 0.753 0.964 1.208 1.553 1.792 2.265 2.718 3.344 3.845 4.343 5.405 6.462

Dimensions A & B shown on the sketch above Loose Fitting

Chart No. 3

GHT

American Standard Straight Pipe Threads for Hose Couplings and Nipples Nominal Size (Hose I.D.) Threads Depth of (ln.) Per ln. Pitch Thread Coupling 0.05648 0.08696 11-1/2 1/2, 5/8, 3/4 Nipple 0.05648 0.08696 11-1/2 1/2, 5/8, 3/4 Female

NPSH

1/2 3/4 1 1-1/4 1-1/2 2

14 14 11-1/2 11-1/2 11-1/2 11-1/2

0.07143 0.07143 0.08696 0.08696 0.08696 0.08696

0.04639 0.04639 0.05648 0.05648 0.05648 0.05648

14 14 11-1/2 11-1/2 11-1/2 11-1/2

0.07143 0.07143 0.08696 0.08696 0.08696 0.08696

0.04639 0.04639 0.05648 0.05648 0.05648 0.05648

Male 1/2 3/4 1 1-1/4 1-1/2 2

Major Diam. Min. 1.0725 Max. 1.0625 Major Diam. Min. 0.8323 1.0428 1.3051 1.6499 1.8888 2.3628 Major Diam. Max. 0.8248 1.0353 1.2951 1.6399 1.8788 2.3528

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The worldâ&#x20AC;&#x2122;s most trusted name in belts, hose and hydraulics. 143

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Couplings for Gates Hoses 1 Long Shank

Description: Cast brass, serrated shank, set has hex male and hex swivel female couplings, with a washer seal. Threads are GHT or NPSM. Sources: A P G Dixon Valve & Coupling Co. Seal-Fast, Inc.

2 Lightweight Water Hose

Description: Spun or wrought brass serrated shank, round swivel female and solid male, both GHT, washer seal. Sources: American Coupling Co. L.R. Nelson Corp.

7 Combination Nipple

Victaulic Nipple Description: Swaged steel with scored or serrated shank, NPT threads same nominal size as I.D. of hose. Special plastic materials available. Sources: A P G Band-It-IDEX, Inc. Campbell Fittings, Inc. Dixon Valve & Coupling Co. Martin Brass Works, Inc. P-T Coupling Co. Seal-Fast, Inc.

8 Tri-Lokt

3 Cast Brass or Zinc Short Shank

Description: Cast brass, serrated shank, hex swivel female with washer, solid male, GHT threads, 3/4-11-1/2. Sources: A P G J.C. Gadd Co. Seal-Fast, Inc.

Description: Machined steel insert, male NPT threads only. Held in place with steel yoke and Band-It Jr. clamps. Insert is reusable â&#x20AC;&#x201D; can be reinstalled with new yoke and clamps. Source: Band-It-IDEX, Inc.

10 Single or Double Bolt Malleable Iron Clamp

4 Machined Brass Short Shank

Description: Machined brass, serrated shank. Each set has round swivel female and solid male, GHT, washer seal. Octagon nut male and female. Sources: American Coupling Co. Anderson Fittings APG Campbell Fittings, Inc. Lenz, Inc.

5 Brass Pin Lug

Description: Cast brass shank and swivel, shank is serrated. NPSM threads in female and male, with washer seal. Sizes under 3â&#x20AC;? have lugs on female only. Sources: A P G Dixon Valve & Coupling Co. P-T Coupling Co.

Description: Cast malleable iron, cadmium plated. Source: Dixon Valve & Coupling Co.

14 Interlocking, Ground Joint

Description: Malleable iron swivel. Inserts and spud may be either steel or malleable iron. All parts are cadmium plated. Male and female threads both NPT with same nominal size as hose l.D. Ground joint between spud and female insert. Available with 2- and 4-bolt clamps. Sources: A P G Dixon Valve & Coupling Co. P-T Coupling Co. Seal-Fast, Inc.

15 Interlocking, Washer Joint

6 Malleable Iron Pin Lug

Description: Malleable iron shank and swivel with serrated shank, cadmium plated. NPSM threads in male and female, washer seal. Pin lugs on female Only. Sources: A P G Dixon Valve & Coupling Co. P-T Coupling Co. Seal-Fast, Inc.

Description: Malleable iron swivel. Insert and spud may be either malleable iron or steel. All parts are cadmium plated. Female thread in spud is NPT with same nominal size as hose I.D. Washer joint between insert and spud. Available with 2- and 4-bolt clamps. Source: Campbell Fittings, Inc. Dixon Valve & Coupling Co. P-T Coupling Co.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 144

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Couplings for Gates Hose—continued 18 Universal Quick Acting

21 Band Rolls

Description: Cast malleable iron with cadmium plate, cast bronze.

Washer seal between two quick-acting heads. Several types of heads are available, but all have same-size attaching heads regardless of hose size. Fingers lock together with quarter-turn rotation. Sources: A P G Campbell Fittings, Inc. Dixon Valve & Coupling Co. P-T Coupling Co. Seal-Fast, Inc.

Description: Available in 100-foot rolls, carbon steel or stainless steel. Buckles—100 per box Sources: Band-It-IDEX, Inc. Fast-Lok Hose Clamps Punch-Lok Co.

23 Reusable Gasoline Pump

19 Standard Air Hose

Description: Machined brass, with serrated shank, NPTF threads on hex solid male and on hex solid female, and NPSM threads on hex swivel female. Sources: American Coupling Co. Anderson Fittings APG Dixon Valve & Coupling Co. Lenz, Inc. National Coupling Co. Plews-Schrader

20 Ferrules

Description: Various materials; Two piece construction. Male NPT or IPT threads (also see coupling 47). Sources: J.C. Gadd Co. P-T Coupling Co. Serv-AII Die and Tool Co.

24 Permanent Gasoline Pump Hose

Description: Various materials; One piece construction. Male NPT or IPT threads. Sources: J.C. Gadd Co. Serv-AII Die and Tool Co.

26 Internal Expansion-Brass Description: All stock ferrules are plain drawn brass. Sources: American Coupling Co. Anderson Fittings Dixon Valve & Coupling Co. Jagemann Stamping Co. Plews-Schrader Truex, Inc. Winzler Stamping Co.

21 Preformed Band Clamps

Description: Body is forged brass. Ferrule is cold-drawn copper alloy. Male coupling has NPT threads, female swivel coupling has NPSH threads. All threads same nominal size as hose l.D. except 1-3/8" l.D. size which has 1-1/2 – 11-1/2 threads. On 1-1/2" and larger sizes, female has special tightening lugs. Sources: Dixon Valve & Coupling Co. ProGrip Co. United Metal Industries, Inc.

26 Ferrules for Internal Expansion

Description: A preformed ring clamp of rust-resistant carbon steel or Type 201 stainless steel. Also available in Type 316 stainless steel, and non-sparking silicon bronze. Sources: Band-It Fast-Lok Hose Clamps Punch-Lok Co.

Sources:

Dixon Valve & Coupling Co. ProGrip Co. United Metal Industries, Inc.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 145

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Couplings for Gates Hoseâ&#x20AC;&#x201D;continued 27 Reusable Petroleum Hose (Compression Ring)

Description: Machined brass coupling body, cast brass sleeve, flat steel wire compression ring. Male NPT or female swivel with NPSM threads and washer seal. Threads are same nominal size as hose I.D. Sources: United Metal Industries, Inc.

28 Barrel Pump

36 Sandblast

Sources:

APG Campbell Fitting, Inc. Dixon Valve & Coupling Co. P-T Coupling Co. Seal-Fast, Inc.

47 Reusable Fuel Oil

Description: Various materials with serrated shank. Threads are male NPT only. Sources: J.C. Gadd Co. Serv-AII Die and Tool Co.

34 Stainless Steel Nipples

Description: Type 316 stainless steel, with serrated shank, solid male NPT threads, hex swivel female, NPSM threads, washer seal. Threads same nominal size as hose l.D Sources: Dixon Valve & Coupling Co. Martin Brass Works, Inc.

Description: This coupling is similar to 23 except it has a brass finish, instead of chrome plating. Male NPTF threads, female NPSM threads, washer seal. Threads same nominal size as hose l.D., except as noted. Sources: United Metal Industries, Inc.

48 Band-It Nipples

Description: Machined steel hex inserts, rust-resistant blued finish, serrated shank, male NPT threads. Source: Band-It-IDEX, Inc.

35 Four-Finger Boss Clamp

Description: Plated iron, stainless steel and brass clamps in 2, 3 and 4 gripping finger configurations. Corresponding stems come in NPT or beveled ends. Available in 2-, 4- and 6-bolt clamps. Follow manufacturer s recommendations for bolt torque and tightening sequence procedures. Sources: Dixon Valve & Coupling Co.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 146

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Couplings for Gates Hose—continued 49 Quick-Connecting

71 Permanent Swaged or Crimped

Description: The basic parts of this coupling are a bronze female shank coupler and a male adapter, which have a washer seal but no threads. These two parts fit snugly together and are held in place by two cams on the female shank coupler which rotate against a groove in the male adapter. This allows the coupling to be connected or disconnected very quickly. Adapters and dust caps are available as shown below. Standard materials are bronze or aluminum. Sources: A P G Dixon Valve & Coupling Co. OPW Engineered Systems P-T Coupling Co. Scully Signal Co. Seal-Fast, Inc.

Part A—Adapter (See NOTE below)

Part C—Shank Coupler (See NOTE below)

Part B—Adapter (See NOTE below)

Solid Male

Ferrule

Description: API or NPT threads on connecting end of stem for easy flange attachment. Strong collar to anchor ferrule to stem. Electroplated steel. Also available in stainless steel, brass and other special metals. Sources: Campbell Fittings, Inc. (Max. 1500 psi) Dixon Valve & Coupling Co. George Myer Company, Inc. ProGrip Co. (Max. 500 psi)

72 Gates Power Crimp

Part D—Coupler (See NOTE below)

Part E—Shank Adapter

Part F—Adapter

Dust Cap

Dust Plug

90˚ Elbow Coupler with Check Valve

90˚ Elbow Coupler without Check Valve

PCS Male

PC Male

PCS Ferrule

PC Ferrule

73 Permanent Swaged or Crimped NOTE:

Part A and Part D have female NPT threads. Part B and Part F have male NPT threads. Above threads have same nominal size as hose l.D. The above couplers and adapters are used to convert threaded-end couplings to quick connect.

61 Center Punch

Cam and Groove

Description: NPT threads on connecting end of stem for easy flange attachment. Strong collar to anchor ferrule to stem. Electroplated steel. Also available in stainless steel, brass and other special metals. Sources: A P G Dixon Valve & Coupling Co. ProGrip Co.

74 Gates MegaCrimp

™

Description: Open-end band or preformed band of rust-resistant steel. Also available in stainless steel. Sources: Fast-Lok Hose Clamps Punch-Lok Co. Description: NPT threads on connecting end of stem for easy ™ flange attachment. Tuffcoat plated steel. The “C” insert assures an even distribution of crimping forces to form a concentric seal. Sources: Gates Corp.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 147

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products 75 Gates GLX

Male Pipe

Couplings for Gates Hose—continued 78 Crimp Sleeves

Female Swivel

Description: One piece staked ferrule design. Smooth ferrule ID designed for textile reinforced transfer hoses. Male pipe NPTF 30° cone seat and female JIC 37° flare swivel terminations. TuffCoat™ plated steel for 400 hour red rust corrosion protection (SAE-J516 and ASTMB-117 salt spray conditions). Sources: Gates Corp.

76 Permanent Crimped Steam Hose Couplings

Description: Available in plated steel, 316 stainless steel and aluminum. Suitable for replacing band clamps when using pin lug, combination nipple or cam and groove stems. Working pressures are determined by the type of couplings and hose used. Sources: APG Campbell Fittings, Inc. Dixon Valve & Coupling Co. P-T Coupling Co.

79 Holedall Permanent Swage Couplings – Long Style

Male Pipe

Female Ground Joint

Description: Permanently crimped steam hose couplings – Female ® Viton Seal Ground Joint or Male NPT Thread. Precision metal to metal contact with a Viton seal provides leak-free performance. Streamlined permanently crimped ferrule eliminates protruding bolts that require retightening and can catch on equipment or cause injury. Sources: Campbell Fittings, Inc.

Description: Patented Holedall couplings include a Holedall stem and specially engineered ferrule. This multi-purpose, high-pressure coupling system requires no bolts and results in a clean coupling with no protrusions. Sources: Dixon Valve & Coupling Co.

77 Gates GSH™ with Integral 2” Fig. 1502 Hammer Unions

Description: One piece, no skive, staked ferrule design. Stem terminations are integral (not Welded) mating male or female Fig. 1502 hammer union subs. The male sub is supplied with a hammer union nut. The female sub is supplied with a rubber lip seal. Sources: Gates Corp.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 148

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Coupling Sources American Couplings Company A Dixon Company Westmont, IL 60559 (800) 323-4440

George Myer Company, Inc. Houston, TX 77023 (800) 600-3074

2 4 19 20 Anderson Fittings Oak Forrest, IL 60452 (800) 323-5284

4 19 20 APG Houston, TX 77020 (800) 888-5223

19 20 Jagemann Stamping Company Manitowoc, WI 54220 (920) 682-4633

20 Lenz, Inc. Dayton, OH 45401 (937) 277-9364

4 19

1 3 4 5 6 7 14 18 19 36 49 73 78 Band-IT-IDEX, Inc. Denver, CO 80216 (303) 320-4555

4 7 15 18 36 71 76 78 Dixon Valve & Coupling Co. Chestertown, MD 21620 (800) 355-1991

1 6 7 10 14 15 18 19 20 26 35 49 71 73 78 79 Fast-Lok Hose Clamps Division of Deco Products Co. Decorah, IA 52101 (800) 327-9751

61 Gadd, J.C., Company Denver, CO 80227 (720) 849-4392

3 23 24 28

Scully Signal Co. Wilmington, MA 01887 (617) 692-8600

49 Seal-Fast, Inc. Houston, TX 77220 (800) 681-1515

1 3 6 7 18 36 49 Martin Brass Works, Inc. Jamaica, NY 11433 (718) 523-3146

7 34

7 8 21 48 Campbell Fittings, Inc. Boyertown, PA 19512 (800) 367-3678

Plews-Schrader Division of Tomkins Ind. & Auto Dixon, IL 61021 (800) 545-1689

Serv-AII Die and Tool Co. Crystal Lake, IL 60014 (815) 459-2900

23 24 28 National Coupling Co. Stafford, TX 77477 (281) 499-2583

19 Nelson Corp., L.R. Peoria, IL 61615 (309) 692-2200

Truex, Inc. Pawtucket, RI 02861 (800) 458-7839

20 United Metal Industries, Inc. New Hyde Park, NY 11040 (800) 359-6801

26 27 OPW Engineered Systems Lebanon, OH 45036 (800) 547-9393

Winzler Stamping Company Montpelier, OH 43543 (419) 485-3147

20 P-T Coupling Co. ProGrip Co. Punch-Lok Co. Enid, OK 73701 (800) 654-0320

5 6 7 14 15 18 21 23 26 49 61 71 73 78

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The worldâ&#x20AC;&#x2122;s most trusted name in belts, hose and hydraulics. 149

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Definitions and Abbreviations API Thread—American Petroleum Institute Thread.

I.D.—Abbreviation for Inside Diameter.

Block Number—A number, e.g., 1, that designates each Gates coupling.

Insert—That part of the coupling which fits into the I.D. of the hose, which often has a threaded end, also called stem or nipple.

Conductive—Rubber designed to transmit electrical current; conducting static electricity

IPT—Iron Pipe Thread. A general term applying to all pipe threads. See Pipe Thread Usage page.

Coupling—A device used to attach a hose to a fitting or other hose in a secure, leakproof manner. There are two primary types: Permanent—A coupling that is applied to the hose with crimping or swaging dies and cannot be easily removed. It is referred to as a "one-time coupling." Reusable—A coupling that can be used more than once. It can be applied to or removed from a hose with the use of simple tools.

MBR—Abbreviation for Minimum Bend Radius. It's the smallest radius, in inches, around which a hose can be bent without overstressing components, collapsing the hose wall and without substantially reducing fluid flow.

Coupling Joint—This leak proof connection is achieved by fastening together the mating surfaces of two couplings. The leak proof seal is obtained by any one of these methods: 1. Washer seal 2. Mechanical seal 3. Thread seal

NPSH—American Standard Straight Pipe Thread for hose couplings and nipples. NPSM—American Standard Straight Pipe Thread—Common name, straight pipe thread for mechanical joints. NPT—American Standard Taper Pipe Thread—Common name, tapered pipe thread. NPTF—American Standard Dryseal Pipe Thread—Common name, dryseal for pressure type joints without sealer.

Ferrule—The external part of the coupling which serves to hold the insert to the hose.

O.D.—Abbreviation for Outside Diameter.

GHT—Garden Hose Thread. See Pipe Thread Usage for compatibility.

Resistant—Rubber designed to prevent transmission of electrical current; nonconductive.

Helix—Reinforcement formed by spiraling a wire or plastic rod around the cylindrical body of hose—usually to resist collapse or improve minimum bend radius.

Shank—That part of the coupling which fits into the I.D. of the hose.

Chart No.1 Coupling Joints

Swivel Female NPSM Threads

Male NPT or NPSM Threads

Washer Seal

Washer Joint

Swivel Female NPSM Threads

Male NPT or NPTF Threads

Male NPTF Threads

Solid Female NPTF Threads

Seal - Metal to Metal Contact

Mechanical Joint

Thread Seal

Dryseal Joint

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 150

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products RMA Tolerances 1.

Hand Built Hose – Wire and Nonwire (W and SB) Size (ln.) 3/4 and under Over 3/4 through 2 Over 2 through 3-1/2 Over 3-1/2 through 4 Over 4 through 6-5/8

O.D. (ln.) ± .031 ± .063 ± .063 ± .063 + .125 - .250

I.D. (ln.) ± .023 ± .031 ± .063 I.D. (ln.) ± .016 ± .023 ± .031 ± .039 ± .039 ± .047 ± .063

Tolerance (ln.)

12 and under ± .125 Over 12 through 24 ± .188 Over 24 through 36 ± .250 Over 36 through 48 ± .375 Over 48 through 72 ± .500 Over 72 ± 1% *Helix wire hoses which can be coiled can appear shorter than the factory cut length. This phenomenon is normal, and the hose(s) will return to the factory cut length upon initial pressurization.

O.D. (ln.) ± .031 ± .031 ± .063

Horizontal Braid Hose (HB and HW) Size (ln.) 1/4, 5/16, 3/8 1/2, 5/8, 3/4 1 1-1/4, 1-1/2 2 2-1/2, 3 3-1/2, 4

Specified Cut Length of Hose* Length (ln.)

Vertical Braid Hose (B) & Spiral Hose Size (ln.) 3/16 1/4 through 3/4 1 through 1-1/2

I.D. (ln.) ± .031 ± .031 ± .047 ± .063 + .063 - .250

O.D. (ln.) ± .031 ± .031 ± .031 ± .047 ± .063 ± .063 ± .063

Made-To-Order Hoses Wire-Inserted Construction, Gates Length (Ft.) up to 5 5 to 10 10 to 25 over 25

Tolerance (ln.) ±1 + 2, -1 ±2 ± 1%

How to Measure Hose Lengths and Assemblies L

Uncoupled L

Coupled or Coupled and Flanged Hose or hose assembly lengths (“L”) are measured as shown above, unless otherwise specified.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 151

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Care and Maintenance of Hose (Reprinted From RMA Hose Handbook)

Hose has a limited life and the user must be alert to signs of impending failure, particularly when the conditions of service include high working pressures and/or the conveyance or containment of hazardous materials. The periodic inspection and testing procedures described here provide a schedule of specific measures which constitute a minimum level of user action to detect signs indicating hose deterioration or loss of performance before conditions leading to malfunction or failure are reached. SAFETY WARNING: Failure to follow properly the manufacturer's recommended procedures for the care, maintenance and storage of a particular hose might result in its failure to perform in the manner intended and might result in possible damage to property and serious bodily injury. General instructions are also described for the proper storage of hose to minimize deterioration from exposure to elements or environments which are known to be deleterious to rubber products. Proper storage conditions can enhance and extend substantially the ultimate life of hose products.

General Care and Maintenance of Hose Hose should not be subjected to any form of abuse in service. It should be handled with reasonable care. Hose should not be dragged over sharp or abrasive surfaces unless specifically designed for such service. Care should be taken to protect hose from severe end loads for which the hose or hose assembly were not designed. Hose should be used at or below its rated working pressure; any changes in pressure should be made gradually so as to not subject the hose to excessive surge pressures. Hose should not be kinked or be run over by equipment. In handling large size hose, dollies should be used whenever possible; slings or handling rigs, properly placed, should be used to support heavy hose used in oil suction and discharge service.

General Test and Inspection Procedures for Hose An inspection and hydrostatic test should be made at periodic intervals to determine if a hose is suitable for continued service. A visual inspection of the hose should be made for loose covers, kinks, bulges or soft spot which might indicate broken or displaced reinforcement. The couplings or fittings should be closely examined and, if there is any sign of movement of the hose from the couplings, the hose should be removed from service. The periodic inspection should include a hydrostatic test for one minute at 150 percent of the recommended working pressure of the hose. An exception to this would be woven jacketed fire hose.* During the hydrostatic test, the hose should be straight, not coiled or in a kinked position. Water is the usual test medium and, following the test, the hose may be flushed with alcohol to remove traces of moisture. A regular schedule for testing should be followed and inspection records maintained.

SAFETY WARNING: Before conducting any pressure tests on hose, provision must be made to ensure the safety of the personnel performing the tests and to prevent any possible damage to property. Only trained personnel using proper tools and procedures should conduct any pressure tests. *Woven jacket fire hose should be tested in accordance with the service test provisions contained in the current edition of National Fire Protection Bulletin No.1962 — Standard for the Care, Use and Service Testing of Fire Hose.

1. Air or any other compressible gas must never be used as the test media because of the explosive action of the hose should a failure occur. Such a failure might result in possible damage to property and serious bodily injury. 2. Air should be removed from the hose by bleeding it through an outlet valve while the hose is being filled with the test medium. 3. Hose to be pressure tested must be restrained by placing steel rods or straps close to each end and at approximate 10 foot (3 m) intervals along its length to keep the hose from "whipping" if failure occurs. The steel rods or straps are to be anchored firmly to the test structure but in such a manner that they do not contact the hose which must be free to move. 4. The outlet end of hose is to be bulwarked so that a blown-out fitting will be stopped. 5. Provisions must be made to protect testing personnel from the forces of the pressure media if a failure occurs. 6. Testing personnel must never stand in front of or in back of the ends of a hose being pressure tested. 7. When liquids such as gasoline, oil, solvent, or other hazardous fluids are used as the test fluid, precautions must be taken to protect against fire or other damage should a hose assembly fail and the test liquid be sprayed over the surrounding area. The Rubber Manufacturers Association has published separately a series of Hose Technical information bulletins describing hoses designed for different applications which detail Maintenance, Testing and Inspection recommendations. Reference should be made to the current RMA Catalog of Publications to determine the availability of the latest edition. Bulletins published as of January 2003 include the following:

Publication No. IP 11—1—Steam Hose IP 11—2—Anhydrous Ammonia Hose IP 11—4—Oil Suction and Discharge Hose IP 11—5—Welding Hose IP 11—7—Chemical Hose IP 11—8—Fuel Dispensing Hose

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 152

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Hose Cleaning There are many different methods used to clean hose assemblies. An apron, safety glasses or face shield, rubber boots and gloves should be worn to help protect the person doing the cleaning from potential injury. Some suggested methods for select hoses in this catalog are listed below. Which method to use and how often cleaning should be performed is based on the following: • Type of hose • Residual material in the hose • Cleanliness requirements for the application • Cleaning facilities available • Consideration for disposal of the residual material and cleaning solutions(s) • Requirements for special applications such as foods, pharmaceuticals, etc.

Solution Recommendations 1. 2. 3. 4. 5.

Cleaning solutions should be chosen that will dissolve or remove the residual material without damaging the hose assembly. A dilute solution of soap in water can often be sufficient. CAUTION – Some chemicals, such as concentrated acids or bases, can react with water releasing heat and byproducts, and possibly splatter. Consult the MSDS of the material being cleaned to identify potential cleaning solutions. After identifying potential cleaning solutions, check Chemical Resistance Table in this catalog for compatibility with hose tube and cover. Non-compatibility of a cleaning solution can cause damage to the hose.

Flushing or Immersing in a Cleaning Bath 1. 2.

D o not exceed the maximum working pressure or temperature for the hose. The cover of the hose should also be washed or wiped to remove any residual material.

Steam Cleaning 1. 2. 3. 4. 5.

S team cleaning is not generally recommended. High temperatures can accelerate aging of a hose and shorten service life. D o not exceed the maximum temperature rating of the hose. Doing so can cause defects such as tube delamination (reducing tube to reinforcement adhesion), tube cracking or tube flow leaving thin spots. N ever use superheated steam! This will exaggerate the potential damages noted above. Only “open end” 50 psi steam should be used. If the hose has blockage, remove it before introducing steam. If the steam source has a wand attached, use caution inserting the wand so that physical damage to the hose is not caused. Sharp edges on the wand can cut the tube, and thin spots could occur where the hot wand contacts the tube.

Shuttle Method 1. 2. 3. 4.

T his is not a recommended cleaning method for hose assemblies. This method uses a shuttle to travel through the inside of the hose assembly to wipe residual material from the hose. The shuttle and residual material can come out of the hose at velocities that could cause injuries or damage. There is also danger from a build up of pressure if the shuttle becomes lodged. The shuttle can cause damage to the hose tube.

Recommended Cleaning of Chemical Hose 1. 2. 3. 4. 5.

Drain the hose after each use. Flush with water or other neutralizing cleaning solution. Properly dispose of drained fluid and cleaning waste. Between uses, store the hose in a clean, dry environment away from sunlight. A void cross contamination. Dedicate a hose to handle a specific chemical.

Recommended Cleaning of Food Hose 1. 2. 3. 4. 5.

Drain the hose after each use. Flush with water or other cleaning solution. Properly dispose of drained material and cleaning waste. Between uses, store the hose in a clean, dry environment away from sunlight. A void cross contamination. Dedicate a hose to handle a specific food material.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 153

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Storage Rubber hose products in storage can be affected adversely by temperature, humidity, ozone, sunlight, oils, solvents, corrosive liquids and fumes, insects, rodents and radioactive materials. The appropriate method for storing hose depends to a great extent on its size (diameter and length), the quantity to be stored and the way in which it is packaged. Hose should not be piled or stacked to such an extent that the weight of the stack creates distortions on the length stored at the bottom. Since hose products vary considerably in size, weight and length, it is not practical to establish definite recommendations on this point. Hose having a very light wall will not support as much load as could a hose having a heavier wall or hose having a wire reinforcement. Hose which is shipped in coils or bales should be stored so that the coils are in a horizontal plane. Whenever feasible, rubber hose products should be stored in their original shipping containers, especially when such containers are wooden crates or cardboard cartons which provide some protection against the deteriorating effects of oils, solvents and corrosive liquids; shipping containers also afford some protection against ozone and sunlight. Certain rodents and insects will damage rubber hose products and adequate protection from them should be provided. Cotton jacketed hose should be protected against fungal growths if the hose is to be stored for prolonged periods in humid conditions in excess of 70 percent.

The ideal temperature for the storage of rubber products ranges for 50º to 70ºF (10-21ºC) with a maximum limit of 100ºF (38ºC). If stored below 32ºF (0ºC), some rubber products become stiff and would require warming before being placed in service. Rubber products should not be stored near sources of heat, such as radiators, base heaters, etc., nor should they be stored under conditions of high or low humidity. To avoid the adverse effects of high ozone concentration, rubber hose products should not be stored near electrical equipment that may generate ozone or be stored for any lengthy period in geographical areas of known high ozone concentration. Hose should not be stored in locations where the ozone level exceeds the National Institute of Occupational Safety and Health’s upper limits of 0.10 ppm. Exposure to direct or reflected sunlight – even through windows – should also be avoided. Uncovered hose should not be stored under fluorescent or mercury lamps which generate light waves harmful to rubber. Storage areas should be relatively cool and dark, and free of dampness and mildew. Items should be stored on a first-in, firstout basis, since even under the best of conditions, an unusually long shelf life could deteriorate certain rubber products.

Decimal and Millimeter Equivalents of Fractions Inches Fractions 1/64 ---------------------------------------1/32 ------------------------3/64 ---------------------------------------1/16 ----------5/64 ---------------------------------------3/32 ------------------------7/64 ---------------------------------------1/8 ------------9/64 ---------------------------------------5/32 ------------------------11/64 -------------------------------------3/16 ----------13/64 -------------------------------------7/32 ------------------------15/64 -------------------------------------1/4 ------------17/64 -------------------------------------9/32 ------------------------19/64 -------------------------------------5/16 ----------21/64 -------------------------------------11/32 ----------------------23/64 -------------------------------------3/8 ------------25/64 -------------------------------------13/32-----------------------27/64--------------------------------------7/16-----------29/64------------------------------------15/32---------------------31/64------------------------------------1/2------------

Decimals .015625 .03125 .046875 .0625 .078125 .09375 .109375 .125 .140625 .15625 .171875 .1875 .203125 .21875 .234375 .250 .265625 .28125 .296875 .3125 .328125 .34375 .359375 .375 .390625 .40625 .421875 .4375 .453125 .46875 .484375 .500

Millimeters .397 .794 1.191 1.588 1.984 2.381 2.778 3.175 3.572 3.969 4.366 4.763 5.159 5.556 5.953 6.350 6.747 7.144 7.541 7.938 8.334 8.731 9.128 9.525 9.922 10.319 10.716 11.113 11.509 11.906 12.303 12.700

Inches Fractions 33/64---------------------------------17/32------------------35/64 --------------------------------9/16 -----37/64 --------------------------------19/32 -----------------39/64 --------------------------------5/8 -------41/64 --------------------------------21/32 -----------------43/64---------------------------------11/16 ----45/64 --------------------------------23/32 -----------------47/64 --------------------------------3/4 -------49/64 --------------------------------25/32------------------51/64---------------------------------13/16----53/64---------------------------------27/32------------------55/64 --------------------------------7/8--------57/64---------------------------------29/32------------------59/64---------------------------------15/16----61/64-------------------------------31/32----------------63/64-------------------------------1---------

Decimals .515625 .53125 .546875 .5625 .578125 .59375 .609375 .625 .640625 .65625 .671875 .6875 .703125 .71875 .734375 .750 .765625 .78125 .796875 .8125 .828125 .84375 .859375 .875 .890625 .90625 .921875 .9375 .953125 .96875 .984375 1.000

Millimeters 13.097 13.494 13.891 14.288 14.684 15.081 15.478 15.875 16.272 16.669 17.066 17.463 17.859 18.256 18.653 19.050 19.447 19.844 20.241 20.638 21.034 21.431 21.828 22.225 22.622 23.019 23.416 23.813 24.209 24.606 25.003 25.400

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 154

Industrial Hose Products

Hose Finder

Rubber hoses are used basically to convey material. They are used for a variety of reasons, but principally for: • • • • •

Flexibility; allows for changes in alignment, hookup or outlet. Absorbing vibration. Resistance to Corrosive fluids. Resistance to abrasion. Providing a closed system.

In applying any product, the more you know about the application, the better the product you choose to meet the needs of the application. This is particularly true with hose because of the many variables involved. Each type of hose and coupling is designed to give satisfactory, safe service life for a particular application. To obtain this service life, the user should: • • • •

Select the proper hose and couplings for the application. Take reasonable care of the hose assembly while it is in service. Maintain the hose assembly in good working condition. Observe all applicable safety regulations.

If a hose assembly was incorrectly selected to solve an application problem, there is very little that care and maintenance can do to prolong its service life. It’s very simple: hoses will fail soon regardless of the care and maintenance provided if they are misapplied. When designing a system with rubber hose, engineering principles regarding materials always apply. Take advantage of the outstanding characteristics of rubber materials listed on the Characteristics and Resistance Information for Hose Tube and Cover Compounds page and avoid those conditions that shorten hose life. Some of these conditions are: • • • •

Exposure to higher-than-rated temperatures. Exposure to severe external abuse such as kinking, pulling, excessive bending. Exposure to corrosive fluids to which hose has little resistance. Subjecting hose to higher than rated working pressure/high surge pressure.

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

The process of selecting hoses from Industrial Hose Products #39496-000 or the following Data Pages usually is resolved in one of two ways: • •

Making the optimum choice from several possible selections for an application. Making the only choice, which satisfies all the requirements of a somewhat special application; i.e., transfer of LP Gas.

Hoses are versatile, and it’s often possible to use one type of hose for several different applications. However, certain specific applications are critical and/or hazardous, and the only type of hose used should be the one Gates recommends for that application. Some of the critical or hazardous applications involving hoses are: • • • •

Steam. Liquid Petroleum Gas (LPG). Corrosive chemicals. Air Drill operation.

Refer to the product description pages in this catalog for details of hoses used in these applications. The hoses listed in this Hose Finder may be found in one or more additional Gates catalogs or Market Specifications publications. The Data Pages are intended to give you a reference for quickly locating standard line hoses for a given application. Hoses are listed by size (I.D.) and rated working pressure. Pertinent specification information is also provided for each hose. Precautionary Notes Not all of the sizes shown are stock items and may require minimum order quantities. In addition, many of the larger diameter hoses (water, material handling, etc.) are made to order. For availability, delivery and pricing information refer to your Industrial Hose Products #39496-000, Customer Service Representative in Denver or your local Gates Representative.

The world’s most trusted name in belts, hose and hydraulics.

155

Industrial Hose Products

Hose Finder

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

PROPER HOSE SELECTION Proper hose selection is the first step in preventive maintenance. Selecting the best product for the application will allow you to obtain the maximum life expectancy from the product for the best value. When selecting the correct hose, use the acronym STAMPED as your guide:

S – Size:

I.D. (Inside Diameter) O.D. (Outside Diameter) Based on the machinery sizing.

T – Temperature:

Consider exterior and interior temperature, as well as temperature impact on the material being conveyed.

A – Application:

Where will the hose be used? How will the hose be used? How often will the hose be used (continuous, intermittent, seldom)? What are the environmental conditions? Special hose construction (crush resistant)? Conductivity requirements? Is the hose used in a critical application? Government or Industrial Standard requirements? Use hoses that are specifically designed for these applications: ound Refueling

M – Material being conveyed:

Chemical name(s) and state(s) – (liquid, solid or gas) Food Dry or powder Liquid

P – Pressure:

What is the working pressure? What is the maximum surge pressure? Is there a vacuum?

E – End requirements:

What type of thread ends? See Coupling Section.

D – Delivery:

Identify how many items and when they need to be supplied. • Distributors – Call Customer Service. • End Users – Call Distributors.

156

Gates Corporation

Hose Finder

Industrial Hose Products Explanation of Column Headings 1. 2. 3.

5. 6.

How to Select a Hose From the Data Pages

Hose I.D. (In.) — This is the nominal hose inside diameter in inches (Refer to RMA Tolerances page). Hose Name — This is the hose identification shown in the catalog. For some special hoses, it may be a number, not a name. Rated Working Pressure (psi) — This is the design working pressure and is based on a certain percentage of the hose burst value. It varies with hose type and intended application. Suction (In. Hg) — This is the vacuum rating of the hose when used in suction applications at ambient temperatures, and not bent beyond the minimum bend radius Hose O.D. — The outside diameter (Refer to RMA Tolerances page). Tube — For reference, the Gates rubber type identification is given and the color used on that particular hose. Refer to Characteristics and Resistance Information for Hose Tube and Cover Compounds page for a description of these stocks. Oil Resistance — RMA Oil Resistance rating is listed: High = High Med. = Medium Low = Low > 100% swell – = Not Rated. Cover — Same information for tube stock. Color Abbreviations: Beige – Beige Blk – Black Blu – Blue Bur – Burgundy Clear – Clear Gld – Gold Grn – Green Gry – Gray

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Example 1 Given: A customer wants a 3/4” I.D. x 20” hose to handle air or water and general purpose applications. Temperatures are ambient, a pressure rating up to 300 psi is required and it must have textile reinforcement with a high oil resistant tube. Turn to Hose Finder Data Pages for the listing of 3/4” I.D. hoses. In the Rated Working Pressure column, you will find the 300 psi figures. NOTE: Several hoses have a 300 psi rating or higher. But, the ones with textile reinforcement and high oil resistance that are multi-purpose are 19B, 119B or Premo Flex® hoses. All of these hoses could be suitable for the application. Refer to corresponding catalog page number for specific hose details and coupling recommendations. Example 2 Given: 6” x 50” dry powder food grade transfer hose is needed. The hose requirements are: full suction, 50 psi and a temperature of 100˚F. Turn to Hose Finder Data Pages for the listing of 6” I.D. hoses. In the Rated Working Pressure column, you will find the 50 psi rating or higher. The two hoses with 50 psi and full suction ratings and suitable for bulk food transfer are 690SB and 692SB. Refer to corresponding catalog page number for specific hose details and coupling recommendations.

Mar – Maroon Nat – Natural Org – Orange Red – Red Tan – Tan Wht – White Yel – Yellow

Refer to the product description pages in this catalog for description of any special cover stripes. 8.

Hose Weight (lb/ft) — This is approximate measurement per current specification. 9. Minimum Bend Radius – This is the smallest radius in inches around which a hose can be bent without overstressing components, without collapsing the hose wall and without substantially reducing fluid flow. 10. Hose Temperature Range – Includes maximum and minimum temperatures of each hose listed. 11. Hose Category — This is a listing of hose types as indicated in the Table of Contents of the Industrial Hose Products #39496-000. Most hoses are not limited to these applications only.

The world’s most trusted name in belts, hose and hydraulics.

157

158

0.12 0.19 0.41 0.44 0.45 0.43 0.25 0.31 0.64 0.64 0.64 0.50 0.50 0.50 0.53 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.62 0.50 0.50 0.62 0.50 0.50 0.47 0.53 0.57 0.47 0.54 0.50 0.62 0.57 0.58 0.62 0.62 0.52 0.58 0.57 0.63 0.48 0.53 0.59 0.38 0.70 0.70 0.70 0.58 0.58 0.56

P P C C C C P P C C C C C C C P P P C C B1 P P P P P B1 C G P B1 C C G1 B1 C C C C Z C C A C C C P C C C C C C

— — C2 A C2 C2 — — A A A M M C2 A P P P A C2 P P P P P P P C2 G P P A A G1 P C2 A A C2 A C2 C4 M C2 C2 C2 — A A A M M C2

1.5 1.5 3.0 2.0 2.0 3.0 2.0 2.0 2.5 2.5 2.5 2.5 2.5 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 2.0 2.0 — 3.0 2.0 3.0 3.0 .7 3.0 2.0 3.0 3.0 3.0 3.0 1.3 3.0 3.0 4.0 4.0 4.0 2.5 3.0 3.0 3.0 3.0 3.0 3.0

Gates Corporation

1.00 1.50 0.07 0.08 0.07 0.07 2.50 3.00 4.73 45.36 8.56 22.40 4.48 0.09 0.11 0.09 0.09 0.09 0.09 0.09 0.09 0.09 0.15 0.09 0.09 0.15 0.09 0.09 0.07 0.10 0.12 0.09 0.11 0.11 0.15 0.12 0.14 0.16 0.14 0.09 0.22 0.12 0.22 5.50 0.15 0.25 1.75 10.15 5.08 53.57 27.95 5.59 0.10

Max.

30.0 30.0 24.0 30.0 30.0 30.0 30.0 30.0 28.0 28.0 28.0 28.0 28.0 24.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 — 30.0 30.0 27.9 30.0 25.0 30.0 30.0 30.0 30.0 30.0 30.0 20.0 30.0 30.0 30.0 30.0 30.0 30.0 28.0 28.0 28.0 28.0 28.0 24.0

Min. Bend Radius (In.) Hose Wt. (Lbs./Ft.)

— — 50 125 250 500 — — 40 40 40 40 40 50 125 200 200 200 250 250 250 250 250 250 250 250 250 250 250 300 300 300 300 300 315 315 350 500 500 500 500 501 1000 3000 3500 6000 — 40 40 40 40 40 50

Temp (°F) Min.

5/16

Cover Type

1/4

Tube Type

7/32

Hose O.D. (In.)

3/16

4219G (Fuel Line & Tank Vent) LPG Vapor Premo Flex 19B Plant Master Vacuum Tubing Vacuum Tubing Fuel Line (USCG Type A1) Fuel Line (USCG Type A1) Fuel Line (USCG Type A1) Fuel Line (USCG Type B) Fuel Line (USCG Type B) 4219G (Fuel Line & Tank Vent) LPG Vapor Adapta Flex Black Adapta Flex Red Adapta Flex Red Cover - UPS Shippable Reels 119B Plant Master 19B Plant Master 6B Dura Master Adapta Flex Black Adapta Flex Black Adapta Flex Blue, Green & Yellow Cover Adapta Flex Red Adapta Flex Red Duro Flex Premo Flex Tufflex Food Adapta Flex Red Duro Flex LOL Plus (Lock-On Hose) Python Plus (Lock-On Hose) Tufflex Plus 6B Dura Master Premo Flex LP350X (Butane-Propane) 119B Plant Master 19B Plant Master 77B (Paint Spray and Chemical) C5M Fuel Line Terminator 319MB Gold Master Pressure Washer Assemblies PowerClean - 1 Wire Braid PowerClean - 2 Wire Braid Vacuum Tubing Fuel Line (USCG Type A1) Fuel Line (USCG Type A1) Fuel Line (USCG Type A1) Fuel Line (USCG Type B) Fuel Line (USCG Type B) 4219G (Fuel Line & Tank Vent)

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Data Pages

Suction (In. Hg.)

Name

7/64 Vacuum Tubing 5/32 Vacuum Tubing

Hose Finder Rated W.P. (psi)

Hose I.D. (In.)

Industrial Hose Products

-40°F -40°F -40°F -30°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -30°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -10°F -40°F -40°F -40°F -20°F -15°F -40°F -40°F -40°F -40°F -40°F -40°F -4°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F

+257°F +257°F +257°F +150°F +212°F +212°F +257°F +257°F +212°F +212°F +212°F +250°F +250°F +257°F +150°F +200°F +200°F +200°F +212°F +212°F +200°F +200°F +200°F +200°F +200°F +200°F +200°F +212°F +130°F +200°F +200°F +212°F +212°F +150°F +200°F +212°F +180°F +212°F +212°F +150°F +212°F +212°F +212°F +250°F +250°F +250°F +257°F +212°F +212°F +212°F +250°F +250°F +257°F

Hose Categories Marine Marine Marine Petroleum Transfer Air and Multi-Purpose Air and Multi-Purpose Marine Marine Marine Marine Marine Marine Marine Marine Petroleum Transfer Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Food and Beverage Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Petroleum Transfer Air and Multi-Purpose Air and Multi-Purpose Acid-Chemical Marine Air and Multi-Purpose Air and Multi-Purpose Pressure Washer Pressure Washer Pressure Washer Marine Marine Marine Marine Marine Marine Marine

Catalog Page No. 66 66 63 113 25 20 66 66 61 61 61 62 62 63 113 30 28 29 21 20 26 30 30 31 28 28 27 25 50 28 27 23 24 32 26 25 112 21 20 19 60 22 33 117 115 116 66 61 61 61 62 62 63

Hose Finder

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

P P P P C A C C2 B1 P C C2 C C2 C C2 Z A C C2 P — C A C A C A C C2 P P MQ MQ C A P P P P P P G G C A C C2 P2 P2 P2 B1 B1 P P P P P P P B1 P C C2 P P P P B1 P C A P P C A G1 G1 B1 P C C2 C A C A C C2 Z A C C4 G G G G A M C2 C2 C A C C2 C C2

Max.

Temp (°F) Min.

Hose Wt. (Lbs./Ft.)

0.62 0.53 0.62 0.62 0.62 0.56 0.67 0.69 0.59 0.67 0.44 0.77 0.77 0.77 0.62 0.69 0.74 0.66 0.66 0.66 0.66 0.63 0.69 0.69 0.78 0.80 0.69 0.66 0.66 0.66 0.66 0.66 0.69 0.67 0.73 0.63 0.75 0.68 0.60 0.75 0.73 0.74 0.75 0.75 0.67 0.75 0.67 0.69 0.77 0.73 0.75 0.68 0.63

Min. Bend Radius (In.)

25.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 20.0 30.0 28.0 28.0 28.0 24.0 25.0 — 25.0 30.0 30.0 30.0 — 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 27.9 30.0 30.0 25.0 30.0 30.0 30.0 30.0 30.0 30.0 25.0 25.0 25.0 30.0 30.0 30.0 30.0 30.0

Cover Type

Hose O.D. (In.)

75 200 250 250 250 250 315 500 500 500 — 40 40 40 50 75 110 125 200 200 200 200 250 250 250 250 250 250 250 250 250 250 300 300 300 300 300 300 300 315 315 350 500 500 500 501 570 800 1000 1000 1125 3000 3000

Tube Type

Suction (In. Hg.)

Name Heater Hose Adapta Flex Red 119B Plant Master 19B Plant Master 6B Dura Master 5/16 Premo Flex Premo Flex 19B Plant Master 77B (Paint Spray and Chemical) C5M Fuel Line Vacuum Tubing Fuel Line (USCG Type A1) Fuel Line (USCG Type A1) Fuel Line (USCG Type A1) 4219G (Fuel Line & Tank Vent) Heater Hose Engine Coolant (Silicone) LPG Vapor Adapta Flex Black Adapta Flex Red Adapta Flex Red Cover - UPS Shippable Reels Tufflex Food 119B Plant Master 19B Plant Master 205MB Steam King 232MB Steam Queen 6B Dura Master Adapta Flex Black Adapta Flex Blue, Green & Yellow Cover Adapta Flex Red Duro Flex 3/8 Premo Flex Adapta Flex Blue, Green & Yellow Cover Adapta Flex Red Duro Flex LOL Plus (Lock-On Hose) Ohmega (Pot Room) Python Plus (Lock-On Hose) Tufflex Plus 6B Dura Master Premo Flex LP350X (Butane-Propane) 119B Plant Master 19B Plant Master 77B (Paint Spray and Chemical) Terminator Thermo AG 570 (Ag Spray) Thermo AG 800 (Ag Spray) 319MB Gold Master Cyclone 33HB (Divers’ Air) PowerClean - 1 Wire Braid Pressure Washer Assemblies

Rated W.P. (psi)

Hose I.D. (In.)

Data Pages

2.0 0.14 -40°F +257°F 3.0 0.09 -40°F +200°F 3.0 0.13 -40°F +212°F 3.0 0.13 -40°F +212°F 3.0 0.14 -40°F +200°F 2.0 0.10 -40°F +212°F 2.0 0.16 -40°F +212°F 3.0 0.17 -40°F +212°F 3.0 0.11 -40°F +150°F 1.3 0.26 -4°F +212°F 3.0 2.50 -40°F +257°F 3.0 11.04 -40°F +212°F 3.0 6.10 -40°F +212°F 3.0 60.99 -40°F +212°F 4.0 0.12 -40°F +257°F 2.5 0.16 -40°F +257°F — 0.19 -65°F +347°F 3.0 0.14 -30°F +150°F 3.0 0.14 -40°F +200°F 3.0 0.14 -40°F +200°F 3.0 0.14 -40°F +200°F — 0.11 -10°F +130°F 3.0 0.15 -40°F +212°F 3.0 0.15 -40°F +212°F 4.0 0.26 -40°F +450°F 4.0 0.30 -40°F +450°F 3.0 0.16 -40°F +200°F 3.0 0.14 -40°F +200°F 3.0 0.14 -40°F +200°F 3.0 0.14 -40°F +200°F 3.0 0.14 -40°F +200°F 3.0 0.14 -40°F +212°F 3.0 0.15 -40°F +200°F 3.0 0.15 -40°F +200°F 3.0 0.18 -40°F +200°F 3.0 0.11 -40°F +212°F 3.0 0.19 -20°F +150°F 3.0 0.15 -20°F +212°F 1.0 0.11 -15°F +150°F 3.0 0.20 -40°F +200°F 3.0 0.18 -40°F +212°F 3.0 0.21 -40°F +180°F 3.0 0.21 -40°F +212°F 3.0 0.18 -40°F +212°F 3.0 0.14 -40°F +150°F 3.0 0.19 -40°F +212°F 4.0 0.12 -10°F +130°F 4.0 0.14 -10°F +130°F 3.0 0.31 -40°F +212°F 4.0 0.18 -40°F +212°F 4.0 0.19 -40°F +120°F 5.0 0.23 -40°F +250°F 5.0 8.50 -40°F +250°F

Hose Categories Marine Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Acid-Chemical Marine Marine Marine Marine Marine Marine Marine Marine Petroleum Transfer Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Food and Beverage Air and Multi-Purpose Air and Multi-Purpose Steam Steam Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Petroleum Transfer Air and Multi-Purpose Air and Multi-Purpose Acid-Chemical Air and Multi-Purpose Acid-Chemical Acid-Chemical Air and Multi-Purpose Pressure Washer Air and Multi-Purpose Pressure Washer Pressure Washer

The world’s most trusted name in belts, hose and hydraulics.

Catalog Page No. 56 28 21 20 26 25 25 20 19 60 66 61 61 61 63 56 55 113 30 28 29 50 21 20 120 121 26 30 31 28 27 25 31 28 27 23 36 24 32 26 25 112 21 20 19 22 17 18 33 118 37 115 117

159

1/2

5/8

160

C C2 C C2 C C2 C C2 C C2 C A C A C A P P MQ MQ D3 D P P P P P P P P G G C A C C2 P2 P2 P2 B1 B1 P P P P P P P B1 P C C2 P P P P B1 P C A P P C A G1 G1 B1 P C C2 C A C A C C2 C C2 C C4 G G Z A G G P C2 A M C A C2 C2 C C2 C C2 C C2 A A C C2 C A

Max.

Temp (°F) Min.

0.68 0.68 0.74 0.77 0.78 0.89 0.89 0.89 0.81 0.87 1.23 0.81 0.81 0.81 0.91 0.75 0.84 0.84 1.06 1.02 0.84 0.81 0.81 0.81 0.81 0.85 0.83 0.83 0.84 0.77 0.88 0.81 0.79 0.88 0.88 0.91 0.88 0.88 0.92 0.89 0.81 0.87 0.84 0.84 0.92 0.94 0.94 0.80 0.76 0.86 0.81 0.94 1.01

Min. Bend Radius (In.) Hose Wt. (Lbs./Ft.)

30.0 30.0 30.0 20.0 10.0 28.0 28.0 28.0 25.0 — 25.0 25.0 25.0 25.0 25.0 — 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 27.9 25.0 30.0 25.0 25.0 25.0 25.0 25.0 25.0 20.0 25.0 25.0 25.0 25.0 30.0 30.0 30.0 30.0 30.0 30.0 30.0 5.0 10.0 28.0

Cover Type

4000 4000 5000 500 35 40 40 40 75 110 150 200 200 200 200 200 250 250 250 250 250 250 250 250 250 250 300 300 300 300 300 300 300 315 315 350 500 500 500 501 570 750 800 1000 1000 1000 1000 2500 3000 4000 10 35 40

Tube Type

Hose O.D. (In.)

13/32

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Data Pages Suction (In. Hg.)

3/8

Name PowerClean - 1 Wire Braid PowerClean - 1 Wire Braid PowerClean - 2 Wire Braid C5M Fuel Line 4219G (Fuel Line & Tank Vent) Fuel Line (USCG Type A1) Fuel Line (USCG Type A1) Fuel Line (USCG Type A1) Heater Hose Engine Coolant (Silicone) 429W (Sand Blast) Adapta Flex Black Adapta Flex Red Adapta Flex Red Cover - UPS Shippable Reels Creamery/Paper Mill Washdown Tufflex Food 119B Plant Master 19B Plant Master 205MB Steam King 232MB Steam Queen 6B Dura Master Adapta Flex Black Adapta Flex Blue, Green & Yellow Cover Adapta Flex Red Duro Flex Premo Flex Adapta Flex Blue, Green & Yellow Cover Adapta Flex Red Duro Flex LOL Plus (Lock-On Hose) Ohmega (Pot Room) Python Plus (Lock-On Hose) Tufflex Plus 6B Dura Master Premo Flex LP350X (Butane-Propane) 119B Plant Master 19B Plant Master C5M Fuel Line Terminator Thermo AG 570 (Ag Spray) 77B (Paint Spray and Chemical) Thermo AG 800 (Ag Spray) 1000 MP/Mine Spray 319MB Gold Master 33HB (Divers’ Air) Cyclone PowerClean - 1 Wire Braid Pressure Washer Assemblies PowerClean - 2 Wire Braid 63SB (Air & Vapor Duct) 4219G (Fuel Line & Tank Vent) Fuel Line (USCG Type A1)

Hose Finder Rated W.P. (psi)

Hose I.D. (In.)

Industrial Hose Products

5.0 0.23 -40°F +250°F 5.0 0.25 -40°F +250°F 5.0 0.35 -40°F +250°F 1.8 0.29 -4°F +212°F 5.0 0.16 -40°F +257°F 5.0 13.33 -40°F +212°F 5.0 66.65 -40°F +212°F 5.0 7.37 -40°F +212°F 3.0 0.19 -40°F +257°F — 0.23 -65°F +347°F 5.0 0.55 -40°F +150°F 5.0 0.19 -40°F +200°F 5.0 0.19 -40°F +200°F 5.0 0.19 -40°F +200°F 5.0 0.28 -40°F +212°F — 0.13 -10°F +130°F 5.0 0.21 -40°F +212°F 5.0 0.20 -40°F +212°F 7.0 0.40 -40°F +450°F 7.0 0.45 -40°F +450°F 5.0 0.21 -40°F +200°F 5.0 0.19 -40°F +200°F 5.0 0.19 -40°F +200°F 5.0 0.19 -40°F +200°F 4.0 0.19 -40°F +200°F 4.0 0.22 -40°F +212°F 5.0 0.20 -40°F +200°F 5.0 0.20 -40°F +200°F 4.0 0.25 -40°F +200°F 5.0 0.15 -40°F +212°F 5.0 0.24 -20°F +150°F 5.0 0.18 -20°F +212°F 1.3 0.13 -15°F +150°F 5.0 0.25 -40°F +200°F 4.0 0.24 -40°F +212°F 5.0 0.28 -40°F +180°F 5.0 0.26 -40°F +212°F 5.0 0.23 -40°F +212°F 2.3 0.40 -4°F +212°F 5.0 0.25 -40°F +212°F 5.0 0.17 -10°F +130°F 5.0 0.23 -40°F +150°F 5.0 0.18 -10°F +130°F 5.0 0.29 -40°F +212°F 5.0 0.42 -40°F +212°F 5.0 0.29 -40°F +120°F 5.0 0.29 -40°F +212°F 7.0 0.28 -40°F +250°F 7.0 11.50 -40°F +250°F 7.0 0.42 -40°F +250°F 1.0 0.12 -30°F +250°F 6.0 0.23 -40°F +257°F 6.0 15.57 -40°F +212°F

Gates Corporation

Hose Categories Pressure Washer Pressure Washer Pressure Washer Marine Marine Marine Marine Marine Marine Marine Material Handling Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Pressure Washer Food and Beverage Air and Multi-Purpose Air and Multi-Purpose Steam Steam Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Petroleum Transfer Air and Multi-Purpose Air and Multi-Purpose Marine Air and Multi-Purpose Acid-Chemical Acid-Chemical Acid-Chemical Mining Air and Multi-Purpose Air and Multi-Purpose Pressure Washer Pressure Washer Pressure Washer Pressure Washer Air and Multi-Purpose Marine Marine

Catalog Page No. 115 115 116 60 63 61 61 61 56 55 71 30 28 29 119 50 21 20 120 121 26 30 31 28 27 25 31 28 27 23 36 24 32 26 25 112 21 20 60 22 17 19 18 74 33 37 118 115 117 116 34 63 61

Hose Finder

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

C A C A P P MQ MQ C J P P P P P P G G C A C C2 P P B1 P C C2 B1 P C A G1 G1 C C2 C C2 C C2 A A A A P P P P MQ MQ D3 D C J P P D D C A C2 C2 G G P P P P P P P P K P K P L P T P T P C A C C2 P2 P2 P2 P2 P2 B1 B1 P P P P P P P P P B1 P S P

Max.

Temp (°F) Min.

Hose Wt. (Lbs./Ft.)

1.01 1.01 0.94 0.99 1.00 0.97 0.97 0.97 0.88 0.94 0.94 0.97 0.98 0.98 0.98 0.94 0.92 0.98 1.00 1.08 0.94 1.00 1.06 1.17 1.12 1.50 1.13 1.27 1.25 1.17 1.33 1.03 1.11 1.11 1.11 1.25 1.25 1.36 1.22 1.29 1.33 1.09 1.09 1.28 1.27 1.27 1.09 1.15 1.15 1.11 1.15 1.15 1.22

Min. Bend Radius (In.)

28.0 28.0 25.0 — 30.0 20.0 20.0 20.0 — 20.0 20.0 20.0 20.0 20.0 20.0 27.9 20.0 20.0 20.0 20.0 5.0 15.0 25.0 5.0 — 15.0 30.0 30.0 25.0 — 30.0 — 15.0 15.0 15.0 15.0 30.0 20.0 30.0 30.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 30.0

Cover Type

Hose O.D. (In.)

40 40 75 110 150 200 200 200 200 250 250 250 250 250 300 300 300 315 500 500 10 20 75 80 110 150 150 150 150 150 150 150 200 200 200 200 200 200 200 200 200 250 250 250 250 250 250 250 250 250 250 250 250

Tube Type

Suction (In. Hg.)

Name Fuel Line (USCG Type A1) Fuel Line (USCG Type A1) Heater Hose Engine Coolant (Silicone) Blacksnake (Curb Pump - Hardwall) Adapta Flex Black Adapta Flex Red Adapta Flex Red Cover - UPS Shippable Reels Tufflex Food 119B Plant Master 5/8 19B Plant Master Adapta Flex Red Duro Flex Premo Flex Duro Flex LOL Plus (Lock-On Hose) Tufflex Plus Premo Flex 19B Plant Master C5M Fuel Line 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) Heater Hose 75W (Standard Wall Coolant) Engine Coolant (Silicone) 429W (Sand Blast) Blacksnake (Curb Pump - Hardwall) Colt Creamery/Paper Mill Washdown Engine Coolant (Oil Resistant - Softwall) Food Master Lite Tufflex Food Adapta Flex Black Adapta Flex Red Adapta Flex Red Cover - UPS Shippable Reels Creamery/Paper Mill Washdown 3/4 Mustang Mustang Crush Resistant Renegade Stallion Stallion Crush Resistant 119B Plant Master 19B Plant Master 205MB Steam King 205MB Steam King 232MB Steam Queen 6B Dura Master Adapta Flex Black Adapta Flex Blue, Green & Yellow Cover Adapta Flex Red Adapta Flex Red Duro Flex Food & Beverage Master

Rated W.P. (psi)

Hose I.D. (In.)

Data Pages

6.0 8.61 -40°F +212°F 6.0 86.10 -40°F +212°F 4.0 0.23 -40°F +257°F — 0.27 -65°F +347°F 6.0 0.37 -40°F +120°F 6.0 0.26 -40°F +200°F 6.0 0.26 -40°F +200°F 6.0 0.26 -40°F +200°F — 0.15 -10°F +130°F 6.0 0.23 -40°F +212°F 6.0 0.22 -40°F +212°F 6.0 0.26 -40°F +200°F 5.0 0.27 -40°F +200°F 5.0 0.27 -40°F +212°F 5.0 0.27 -40°F +200°F 6.0 0.20 -40°F +212°F 1.8 0.20 -15°F +150°F 5.0 0.27 -40°F +212°F 6.0 0.27 -40°F +212°F 2.8 0.51 -4°F +212°F 1.0 0.14 -30°F +250°F 1.0 0.20 -30°F +250°F 5.0 0.26 -40°F +257°F 6.0 0.37 -40°F +257°F — 0.31 -65°F +347°F 8.0 0.70 -40°F +150°F 6.0 0.42 -40°F +120°F 3.0 0.50 -40°F +250°F 6.0 27.50 -20°F +180°F 6.0 0.34 -40°F +212°F 2.0 0.65 -40°F +230°F — 0.20 -10°F +130°F 6.0 0.32 -40°F +200°F 6.0 0.31 -40°F +200°F 6.0 0.31 -40°F +200°F 6.0 0.49 -40°F +212°F 4.0 0.45 -40°F +250°F 4.0 0.53 -40°F +250°F 4.0 0.41 -40°F +212°F 4.0 0.52 -40°F +300°F 4.0 0.53 -40°F +300°F 6.0 0.29 -40°F +212°F 6.0 0.28 -40°F +212°F 9.0 0.49 -40°F +450°F 9.0 0.57 -40°F +450°F 9.0 0.60 -40°F +450°F 6.0 0.29 -40°F +200°F 6.0 0.35 -40°F +200°F 6.0 0.35 -40°F +200°F 6.0 0.35 -40°F +200°F 6.0 0.35 -40°F +200°F 5.0 0.36 -40°F +200°F 2.0 0.42 -40°F +230°F

Hose Categories Marine Marine Marine Marine Petroleum Transfer Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Food and Beverage Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Marine Air and Multi-Purpose Air and Multi-Purpose Marine Marine Marine Material Handling Petroleum Transfer Acid-Chemical Pressure Washer Marine Food and Beverage Food and Beverage Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Pressure Washer Acid-Chemical Acid-Chemical Acid-Chemical Acid-Chemical Acid-Chemical Air and Multi-Purpose Air and Multi-Purpose Steam Steam Steam Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Food and Beverage

The world’s most trusted name in belts, hose and hydraulics.

Catalog Page No. 61 61 56 55 114 30 28 29 50 21 20 28 27 25 27 23 32 25 20 60 34 35 56 51 55 71 114 16 119 53 41 50 30 28 29 119 12 13 15 10 11 21 20 120 120 121 26 30 31 28 28 27 38

161

162

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

C C2 P P P P B1 P C A P P G1 G1 B1 P C C2 C A C A A C2 C C2 C D3 C C2 C C4 G G Z A G G P C2 A M C2 C2 A A P P MQ MQ C A P P C C2 A A A A C A G — G G D3 D P P P G MQ MQ G G G — C A P P G G G G C A P P D3 D D3 D P P P P P P C J P P D D

Max.

Temp (°F) Min.

1.15 1.15 1.15 1.15 1.06 1.16 1.07 1.19 1.19 1.23 1.19 1.28 1.19 1.11 1.11 1.22 1.08 1.16 1.41 1.10 1.21 1.20 1.06 1.25 1.24 1.30 1.38 1.23 1.19 1.25 1.40 1.26 1.26 1.39 1.34 1.34 1.37 1.27 1.27 1.44 1.46 1.29 1.31 1.42 1.38 1.63 1.87 1.40 1.39 1.33 1.38 1.52 1.50

Min. Bend Radius (In.) Hose Wt. (Lbs./Ft.)

20.0 15.0 15.0 20.0 15.0 20.0 15.0 20.0 20.0 20.0 20.0 25.0 20.0 25.0 25.0 15.0 25.0 25.0 25.0 25.0 25.0 30.0 5.0 7.0 — — 15.0 20.0 5.0 15.0 20.0 28.0 28.0 20.0 25.0 28.0 — 28.0 28.0 25.0 25.0 28.0 — — 7.0 5.0 5.0 10.0 10.0 30.0 30.0 30.0 15.0

Cover Type

250 300 300 300 300 300 300 315 315 350 500 500 500 500 500 501 570 750 800 1000 1000 1000 10 75 110 150 175 500 10 20 35 35 40 50 75 80 90 90 90 100 100 100 125 135 140 150 150 150 150 150 150 150 150

Tube Type

Hose O.D. (In.)

Data Pages Suction (In. Hg.)

Name Premo Flex Adapta Flex Blue, Green & Yellow Cover Adapta Flex Red Duro Flex LOL Plus (Lock-On Hose) Ohmega (Pot Room) Tufflex Plus 6B Dura Master Premo Flex LP350X (Butane-Propane) 119B Plant Master 3/4 18MB Air Drill 19B Plant Master 500 MP Air Drill 500 MP Air Drill Terminator Thermo AG 570 (Ag Spray) 77B (Paint Spray and Chemical) Thermo AG 800 (Ag Spray) 1000 MP/Mine Spray 319MB Gold Master Cyclone 63SB (Air & Vapor Duct) 75W (Standard Wall Coolant) Engine Coolant (Silicone) 7/8 Engine Coolant (Oil Resistant - Softwall) 76W (Heavy Wall Coolant) C5M Fuel Line 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) Fuel Fill (USCG Type A1 and B1) Master-Flex 101CL Master-Flex 201CR 770SB Heater Hose Master-Flex 300 EPDM Engine Coolant (Silicone) Master-Flex 100GR Master-Flex 101CL 4684CF (Wet Exhaust - Corrugated) 1 Engine Coolant (Wire Inserted - Hardwall) Master-Flex 200CL Tufflex Food Engine Coolant (Oil Resistant - Softwall) 75W (Standard Wall Coolant) 429W (Sand Blast) 429W (Sand Blast) Adapta Flex Black Adapta Flex Red Barracuda Blacksnake (Curb Pump - Hardwall) Colt Creamery/Paper Mill Washdown

Hose Finder Rated W.P. (psi)

Hose I.D. (In.)

Industrial Hose Products

5.0 0.36 -40°F +212°F 6.0 0.35 -40°F +200°F 6.0 0.35 -40°F +200°F 5.0 0.36 -40°F +200°F 7.0 0.24 -40°F +212°F 6.0 0.36 -20°F +150°F 2.5 0.29 -15°F +150°F 6.0 0.40 -40°F +200°F 5.0 0.40 -40°F +212°F 6.0 0.44 -40°F +180°F 6.0 0.42 -40°F +212°F 6.0 0.60 -30°F +212°F 6.0 0.38 -40°F +212°F 6.0 0.41 -22°F +180°F 6.0 0.41 -22°F +180°F 6.0 0.42 -40°F +212°F 6.0 0.27 -10°F +130°F 6.0 0.35 -40°F +150°F 6.0 0.30 -10°F +130°F 8.0 0.43 -40°F +212°F 8.0 0.60 -40°F +212°F 6.0 0.41 -40°F +212°F 1.0 0.17 -30°F +250°F 7.0 0.39 -40°F +257°F — 0.35 -65°F +347°F 7.0 0.38 -40°F +212°F 7.0 0.58 -40°F +257°F 3.5 0.51 -4°F +212°F 1.0 0.20 -30°F +250°F 1.0 0.26 -30°F +250°F 4.0 27.01 -40°F +212°F 2.0 0.14 -10°F +130°F 2.0 0.14 -10°F +130°F 5.0 0.49 -40°F +150°F 7.0 0.37 -40°F +257°F 4.0 0.23 -30°F +140°F — 0.40 -65°F +347°F 3.0 0.27 -10°F +130°F 3.0 0.27 -10°F +130°F 3.0 0.51 -40°F +212°F 2.0 2.50 -40°F +257°F 3.0 0.30 -10°F +130°F — 0.32 -10°F +130°F 8.0 0.43 -40°F +212°F 8.0 0.42 -40°F +257°F 12.0 0.70 -40°F +150°F 12.0 1.01 -40°F +150°F 8.0 0.44 -40°F +200°F 8.0 0.43 -40°F +200°F 5.0 0.39 -40°F +180°F 8.0 0.57 -40°F +120°F 3.5 0.61 -40°F +250°F 8.0 33.50 -20°F +180°F

Gates Corporation

Hose Categories Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Petroleum Transfer Air and Multi-Purpose Mining Air and Multi-Purpose Mining Mining Air and Multi-Purpose Acid-Chemical Acid-Chemical Acid-Chemical Mining Air and Multi-Purpose Pressure Washer Air and Multi-Purpose Marine Marine Marine Marine Marine Air and Multi-Purpose Air and Multi-Purpose Marine Water Food and Beverage Material Handling Marine Material Handling Marine Water Water Marine Marine Food and Beverage Food and Beverage Marine Marine Material Handling Material Handling Air and Multi-Purpose Air and Multi-Purpose Water Petroleum Transfer Acid-Chemical Pressure Washer

Catalog Page No. 25 31 28 27 23 36 32 26 25 112 21 78 20 79 79 22 17 19 18 74 33 118 34 51 55 53 52 60 34 35 64 131 48 70 56 72 55 130 131 59 54 47 50 53 51 71 71 30 28 125 114 16 119

Hose Finder

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

3.0 3.0 3.0 3.0 5.0 3.0 8.0 8.0 8.0 8.0 8.0 8.0 5.0 5.0 5.0 5.0 5.0 3.5 8.0 8.0 11.0 11.0 11.0 8.0 3.0 8.0 3.0 8.0 8.0 10.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 11.0 11.0 12.0 12.0 12.0 — 4.0 2.5 2.5 — 8.0 8.0 8.0 1.0 1.0

0.79 0.60 0.53 0.59 0.53 0.52 0.59 0.45 0.45 0.45 0.65 0.58 0.56 0.64 0.51 0.63 0.63 0.44 0.42 0.41 0.70 0.78 0.73 0.42 0.52 0.54 0.52 0.54 0.54 0.61 0.59 0.60 0.62 0.80 0.55 0.65 0.66 0.57 0.66 0.77 1.49 1.49 1.49 0.44 0.56 2.75 7.40 5.59 0.47 0.48 0.64 0.22 0.34

Max.

C2 C2 C A C C2 C C2 P D C D P P P P P P P P P P C C4 K P K P L P T P T P G1 G1 C A C C2 P2 P2 P2 P2 P2 B1 B1 P S P B1 P S P C C2 P P D2 P B1 P C A C A A C2 C C2 C C2 C D3 C C4 P C2 A M C A C A C A MQ MQ C A P P P P P P P P C A P P A A A A

Temp (°F) Min.

Hose Wt. (Lbs./Ft.)

1.58 1.50 1.50 1.50 1.45 1.42 1.50 1.40 1.39 1.40 1.52 1.50 1.50 1.61 1.47 1.56 1.58 1.44 1.38 1.38 1.52 1.63 1.52 1.38 1.48 1.47 1.48 1.47 1.47 1.53 1.50 1.51 1.50 1.55 1.50 1.45 1.45 1.51 1.42 1.46 1.53 1.53 1.53 1.50 1.56 1.58 1.50 1.40 1.50 1.55 1.63 1.44 1.50

Min. Bend Radius (In.)

30.0 30.0 30.0 30.0 30.0 30.0 10.0 10.0 10.0 10.0 15.0 10.0 30.0 20.0 30.0 30.0 20.0 15.0 10.0 10.0 20.0 20.0 20.0 10.0 30.0 10.0 30.0 10.0 10.0 15.0 20.0 15.0 20.0 25.0 20.0 25.0 25.0 10.0 25.0 25.0 — — — — 25.0 25.0 25.0 — 6.0 — 10.0 5.0 15.0

Cover Type

Hose O.D. (In.)

150 150 150 150 150 150 175 200 200 200 200 200 200 200 200 200 200 200 250 250 250 250 250 250 250 250 250 250 300 300 315 350 500 500 500 500 500 501 1000 1000 5000 5000 6000 90 100 100 100 100 125 135 175 10 20

Tube Type

Suction (In. Hg.)

Name Food Master Lite Longhorn Longhorn AF (Alternative Fuel-Corrugated) Longhorn AF (Alternative Fuel-Corrugated) Shark Super-Vac 76W (Heavy Wall Coolant) Adapta Flex Black Adapta Flex Red Adapta Flex Red Cover - UPS Shippable Reels Creamery/Paper Mill Washdown Fuel Oil Delivery Mustang Mustang Crush Resistant Renegade Stallion Stallion Crush Resistant Tufflex Plus 119B Plant Master 19B Plant Master 205MB Steam King 1 205MB Steam King 232MB Steam Queen 6B Dura Master Cellar Master Duro Flex Food & Beverage Master Premo Flex Adapta Flex Red Aquarius Potable Water 6B Dura Master LP350X (Butane-Propane) 119B Plant Master 18MB Air Drill 19B Plant Master 500 MP Air Drill 500 MP Air Drill Terminator 1000 MP/Mine Spray 319MB Gold Master 16 EFBOP Blow-Out Preventer Powerbraid Plus (Slim Hole Rotary) 16 EFBOP Blow-Out Preventer Engine Coolant (Silicone) 4684CF (Wet Exhaust - Corrugated) Engine Coolant (Wire Inserted - Hardwall) Wet Exhaust (Hardwall) 1 1/8 Wet Exhaust (Softwall) 75W (Standard Wall Coolant) Engine Coolant (Oil Resistant - Softwall) 76W (Heavy Wall Coolant) 63SB (Air & Vapor Duct) 1 1/4 163SB (Air & Vapor Duct - Heavy Duty)

Rated W.P. (psi)

Hose I.D. (In.)

Data Pages

-40°F -40°F -30°F -30°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -15°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -30°F -40°F -22°F -22°F -40°F -40°F -40°F -40°F -40°F -40°F -65°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -30°F -30°F

+230°F +180°F +180°F +180°F +180°F +150°F +257°F +200°F +200°F +200°F +212°F +180°F +250°F +250°F +212°F +300°F +300°F +150°F +212°F +212°F +450°F +450°F +450°F +200°F +230°F +200°F +230°F +212°F +200°F +150°F +200°F +180°F +212°F +212°F +212°F +180°F +180°F +212°F +212°F +212°F +250°F +180°F +250°F +347°F +212°F +257°F +257°F +257°F +257°F +212°F +257°F +250°F +250°F

Hose Categories Food and Beverage Petroleum Transfer Petroleum Transfer Petroleum Transfer Water Petroleum Transfer Marine Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Pressure Washer Petroleum Transfer Acid-Chemical Acid-Chemical Acid-Chemical Acid-Chemical Acid-Chemical Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Steam Steam Steam Air and Multi-Purpose Food and Beverage Air and Multi-Purpose Food and Beverage Air and Multi-Purpose Air and Multi-Purpose Food and Beverage Air and Multi-Purpose Petroleum Transfer Air and Multi-Purpose Mining Air and Multi-Purpose Mining Mining Air and Multi-Purpose Mining Air and Multi-Purpose Oilfield Oilfield Oilfield Marine Marine Marine Marine Marine Marine Marine Marine Air and Multi-Purpose Air and Multi-Purpose

The world’s most trusted name in belts, hose and hydraulics.

Catalog Page No. 41 97 98 98 124 101 52 30 28 29 119 110 12 13 15 10 11 32 21 20 120 120 121 26 39 27 38 25 28 43 26 112 21 78 20 79 79 22 74 33 96 95 96 55 59 54 58 57 51 53 52 34 35

163

164

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

D3 D G — G G P G MQ MQ G G G — G G C A P P P P G G P P P P P P C A D3 D P P P P D D P P C A C C2 P D C D B1 P C C4 K P L P C A C C2 P2 P2 P P B1 P C C2 C A A C2 C C2 C C2 C D3 C C4 P C2 A M C A A A A A C A C A MQ MQ P P P P C A P P

Max.

Temp (°F) Min.

1.64 1.61 1.61 1.61 1.63 1.53 1.53 1.56 1.69 1.63 1.71 1.75 1.63 1.53 1.74 1.67 2.16 1.61 1.79 1.75 1.53 1.75 1.75 1.71 1.68 1.73 1.75 1.75 1.72 1.75 1.75 1.81 1.73 1.73 1.75 1.85 1.80 1.75 1.74 1.74 1.78 1.69 1.69 1.97 1.52 1.63 1.63 1.81 1.75 1.83 1.75 1.80 1.75

Min. Bend Radius (In.) Hose Wt. (Lbs./Ft.)

20.0 28.0 28.0 28.0 — 28.0 28.0 28.0 25.0 5.0 25.0 — 25.0 — 10.0 — 5.0 30.0 30.0 15.0 — 30.0 30.0 30.0 30.0 10.0 10.0 30.0 30.0 10.0 10.0 20.0 10.0 10.0 10.0 10.0 15.0 10.0 15.0 15.0 10.0 20.0 20.0 — 5.0 15.0 30.0 25.0 — 25.0 4.0 — 25.0

Cover Type

50 50 50 70 85 90 90 90 100 100 100 100 100 100 125 135 150 150 150 150 150 150 150 150 150 200 200 200 200 250 250 250 250 250 250 350 500 500 500 500 501 1000 1000 5000 10 15 20 85 85 85 100 100 100

Tube Type

Hose O.D. (In.)

Data Pages Suction (In. Hg.)

Name 770SB Master-Flex 101CL Master-Flex 201CR Master-Flex 300 EPDM Engine Coolant (Silicone) Master-Flex 100GR Master-Flex 101CL Master-Flex 200CL 4684CF (Wet Exhaust - Corrugated) 75W (Standard Wall Coolant) Engine Coolant (Wire Inserted - Hardwall) Tufflex Food Wet Exhaust (Hardwall) Wet Exhaust (Softwall) 76W (Heavy Wall Coolant) Engine Coolant (Oil Resistant - Softwall) 429W (Sand Blast) Barracuda Colt Creamery/Paper Mill Washdown Dolphin Longhorn 1 1/4 Longhorn AF (Alternative Fuel-Corrugated) Shark Super-Vac 6B Dura Master Fuel Oil Delivery Mustang Renegade 119B Plant Master 19B Plant Master 205MB Steam King Adapta Flex Black Duro Flex Premo Flex LP350 (Butane-Propane) 18MB Air Drill 19B Plant Master 500 MP Air Drill 500 MP Air Drill Terminator 1000 MP/Mine Spray 319MB Gold Master Powerbraid Plus (Slim Hole Rotary) 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) 4663K (Fuel Fill - Corrugated) 4684CF (Wet Exhaust - Corrugated) 1 3/8 Engine Coolant (Silicone) Engine Coolant (Wire Inserted - Hardwall) 75W (Standard Wall Coolant) Engine Coolant (Oil Resistant - Softwall) Wet Exhaust (Hardwall)

Hose Finder Rated W.P. (psi)

Hose I.D. (In.)

Industrial Hose Products

5.0 0.59 -40°F +150°F 3.0 0.31 -10°F +130°F 3.0 0.31 -10°F +130°F 5.0 0.30 -30°F +140°F — 0.48 -65°F +347°F 4.0 0.36 -10°F +130°F 4.0 0.34 -10°F +130°F 4.0 0.38 -10°F +130°F 4.0 0.61 -40°F +212°F 12.0 0.51 -40°F +257°F 2.5 3.00 -40°F +257°F — 0.63 -10°F +130°F 2.5 8.03 -40°F +257°F — 6.07 -40°F +257°F 12.0 0.70 -40°F +257°F 10.0 0.51 -40°F +212°F 12.0 1.22 -40°F +150°F 5.0 0.51 -40°F +180°F 4.0 0.77 -40°F +250°F 10.0 39.50 -20°F +180°F — 0.37 -40°F +180°F 4.0 0.72 -40°F +180°F 4.0 0.70 -30°F +180°F 6.0 0.68 -40°F +180°F 3.0 0.67 -40°F +150°F 10.0 0.67 -40°F +200°F 10.0 0.75 -40°F +180°F 6.0 0.66 -40°F +250°F 6.0 0.60 -40°F +212°F 10.0 0.69 -40°F +212°F 10.0 0.67 -40°F +212°F 16.0 0.90 -40°F +450°F 10.0 0.68 -40°F +200°F 10.0 0.67 -40°F +200°F 10.0 0.67 -40°F +212°F 10.0 0.89 -40°F +180°F 10.0 0.95 -30°F +212°F 10.0 0.76 -40°F +212°F 10.0 0.85 -22°F +180°F 10.0 0.86 -22°F +180°F 10.0 0.73 -40°F +212°F 16.0 0.81 -40°F +212°F 16.0 0.87 -40°F +212°F 16.5 2.67 -40°F +180°F 1.5 0.24 -30°F +250°F 1.5 0.44 -30°F +250°F 5.0 0.38 -40°F +212°F 4.0 0.66 -40°F +212°F — 0.52 -65°F +347°F 3.0 3.25 -40°F +257°F 12.0 0.55 -40°F +257°F 12.0 0.56 -40°F +212°F 3.0 8.66 -40°F +257°F

Gates Corporation

Hose Categories Material Handling Water Food and Beverage Material Handling Marine Water Water Food and Beverage Marine Marine Marine Food and Beverage Marine Marine Marine Marine Material Handling Water Acid-Chemical Pressure Washer Water Petroleum Transfer Petroleum Transfer Water Petroleum Transfer Air and Multi-Purpose Petroleum Transfer Acid-Chemical Acid-Chemical Air and Multi-Purpose Air and Multi-Purpose Steam Air and Multi-Purpose Air and Multi-Purpose Air and Multi-Purpose Petroleum Transfer Mining Air and Multi-Purpose Mining Mining Air and Multi-Purpose Mining Air and Multi-Purpose Oilfield Air and Multi-Purpose Air and Multi-Purpose Marine Marine Marine Marine Marine Marine Marine

Catalog Page No. 70 131 48 72 55 130 131 47 59 51 54 50 58 57 52 53 71 125 16 119 128 97 98 124 101 26 110 12 15 21 20 120 30 27 25 111 78 20 79 79 22 74 33 95 34 35 65 59 55 54 51 53 58

Hose Finder

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

P P P P C C4 C C2 C C2 U G A A A A C A C A C A C G D3 D G — G G P G G G G G C A MQ MQ P P G G G — G G P P C A P P P P P P P P D3 D D2 D3 C P P P S P P P P P C 2 C2 C A C C2 P D P D C 2 C2 P D D D C D B1 P K L C C2 K P K P K P L P

Max.

Temp (°F) Min.

Hose Wt. (Lbs./Ft.)

1.69 1.88 1.87 1.87 1.88 1.88 1.69 1.75 1.90 1.90 1.77 1.88 1.89 1.86 1.82 1.96 1.67 2.00 1.94 1.88 1.96 1.82 1.82 1.84 1.88 1.92 1.88 1.78 2.00 2.08 2.37 2.23 2.07 1.86 2.00 2.04 1.78 2.10 2.02 2.02 1.82 1.90 2.07 1.96 1.98 1.97 1.98 1.97 2.08 2.04 2.04 2.13 2.00

Min. Bend Radius (In.)

— 10.0 10.0 10.0 10.0 — 5.0 15.0 20.0 20.0 30.0 28.0 20.0 28.0 28.0 28.0 — — 25.0 — 20.0 28.0 28.0 28.0 3.0 — 20.0 — 10.0 30.0 5.0 30.0 30.0 30.0 30.0 30.0 — 30.0 30.0 30.0 — — — 30.0 — 30.0 10.0 30.0 10.0 30.0 30.0 20.0 30.0

Cover Type

Hose O.D. (In.)

100 110 200 250 500 5 10 15 18 18 20 40 50 50 50 60 75 75 85 85 85 90 90 90 100 100 100 100 112 130 135 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 200 200 200 200 200 200 200

Tube Type

Suction (In. Hg.)

Name Wet Exhaust (Softwall) 76W (Heavy Wall Coolant) 1 3/8 Fuel Oil Delivery 19B Plant Master 19B Plant Master Master-Flex Vapor Recovery 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) Fuel Fill (USCG Type A1 and B1) Fuel Fill (USCG Type A1 and B1) 4663K (Fuel Fill - Corrugated) Master-Flex 400 770SB Master-Flex 101CL Master-Flex 201CR Master-Flex 300 EPDM Master-Flex 500 Tufflex Food 4684CF (Wet Exhaust - Corrugated) Engine Coolant (Silicone) Engine Coolant (Wire Inserted - Hardwall) Master-Flex 100GR Master-Flex 101CL Master-Flex 200CL 75W (Standard Wall Coolant) Engine Coolant (Oil Resistant - Softwall) Wet Exhaust (Hardwall) Wet Exhaust (Softwall) 76W (Heavy Wall Coolant) 1 1/2 Hot Air Blower 429W (Sand Blast) 690SB (Bulk Commodity) 692SB (Bulk Commodity) Barracuda Cellar Master Light Colt Dolphin Food Master Lite Longhorn Longhorn AF (Alternative Fuel-Corrugated) Marlin Marlin Sani-Pure Shark Steelhead Super-Vac 6B Dura Master Appaloosa Fuel Oil Delivery Mustang Mustang Mustang Crush Resistant Renegade

Rated W.P. (psi)

Hose I.D. (In.)

Data Pages

— 6.58 -40°F +257°F 12.0 0.76 -40°F +257°F 10.0 0.80 -40°F +180°F 10.0 0.71 -40°F +212°F 10.0 0.73 -40°F +212°F 1.5 0.36 -30°F +140°F 1.5 0.26 -30°F +250°F 1.5 0.48 -30°F +250°F 7.0 37.74 -40°F +212°F 7.0 9.44 -40°F +212°F 5.0 0.41 -40°F +212°F 3.0 0.38 -30°F +140°F 6.0 0.68 -40°F +150°F 3.0 0.37 -10°F +130°F 3.0 0.37 -10°F +130°F 6.0 0.49 -30°F +140°F — 0.17 +25°F +120°F — 0.74 -10°F +130°F 4.0 0.70 -40°F +212°F — 0.57 -65°F +347°F 3.5 3.50 -40°F +257°F 5.0 0.47 -10°F +130°F 5.0 0.47 -10°F +130°F 5.0 0.48 -10°F +130°F 12.0 0.51 -40°F +257°F 12.0 0.60 -40°F +212°F 3.5 9.31 -40°F +257°F — 7.12 -40°F +257°F 12.0 0.81 -40°F +257°F 8.0 0.89 -40°F +350°F 18.0 1.37 -40°F +150°F 10.0 1.41 -40°F +150°F 9.0 1.13 -40°F +180°F 6.0 0.60 -40°F +180°F 6.0 0.77 -40°F +212°F 5.0 0.89 -40°F +250°F — 0.43 -40°F +180°F 4.5 1.14 -40°F +230°F 4.0 0.88 -40°F +180°F 4.0 0.87 -30°F +180°F 12.0 0.47 -40°F +180°F 12.0 0.63 -40°F +180°F 18.0 0.97 -40°F +230°F 8.0 0.79 -40°F +180°F 12.0 0.70 -40°F +150°F 3.0 0.77 -40°F +150°F 12.0 0.79 -40°F +200°F 8.0 0.76 -40°F +225°F 12.0 0.95 -40°F +180°F 8.0 0.87 -40°F +250°F 8.0 0.88 -40°F +250°F 8.0 0.90 -40°F +250°F 8.0 0.78 -40°F +212°F

Hose Categories Marine Marine Petroleum Transfer Air and Multi-Purpose Air and Multi-Purpose Petroleum Transfer Air and Multi-Purpose Air and Multi-Purpose Marine Marine Marine Material Handling Material Handling Water Food and Beverage Material Handling Water Food and Beverage Marine Marine Marine Water Water Food and Beverage Marine Marine Marine Marine Marine Material Handling Material Handling Food and Beverage Food and Beverage Water Food and Beverage Acid-Chemical Water Food and Beverage Petroleum Transfer Petroleum Transfer Water Water Food and Beverage Water Water Petroleum Transfer Air and Multi-Purpose Acid-Chemical Petroleum Transfer Acid-Chemical Acid-Chemical Acid-Chemical Acid-Chemical

The world’s most trusted name in belts, hose and hydraulics.

Catalog Page No. 57 52 110 20 20 109 34 35 64 64 65 73 70 131 48 72 129 50 59 55 54 130 131 47 51 53 58 57 52 69 71 44 45 125 40 16 128 41 97 98 127 127 42 124 126 101 26 14 110 12 12 13 15

165

166

T P T P T P C A C C2 P2 P2 P2 B1 P P S P B1 P S P C C2 A A A D3 C C2 C C2 C D3 C C4 J J B1 J P C2 A M A A A A A A C A C A C A C A P P MQ MQ C A P P P P P P P P D D A A A A C A C A P P C A P P MQ MQ P P P P P P A A A A C A C A C A

Min. Bend Radius (In.) Hose Wt. (Lbs./Ft.)

Cover Type

2.05 2.05 2.08 2.00 2.00 2.14 2.18 1.98 2.07 1.98 2.07 2.00 2.25 2.21 2.00 1.99 1.99 2.09 2.02 2.02 1.92 1.94 2.26 1.81 1.88 2.03 2.03 1.90 2.06 2.08 2.00 2.05 2.00 2.00 1.91 2.13 2.10 1.94 2.00 2.02 2.19 2.13 2.17 2.21 2.13 2.25 2.12 2.03 2.06 2.13 2.28 2.28 2.14

Tube Type

30.0 30.0 20.0 10.0 10.0 10.0 10.0 10.0 30.0 10.0 30.0 10.0 10.0 15.0 10.0 15.0 15.0 10.0 — — 15.0 15.0 — 5.0 15.0 20.0 20.0 30.0 20.0 20.0 — — 2.0 20.0 — 7.0 — 5.0 15.0 30.0 20.0 1.0 — 20.0 — 5.0 20.0 — 5.0 15.0 20.0 20.0 30.0

8.0 8.0 8.0 12.0 12.0 20.0 20.0 12.0 4.5 12.0 4.5 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 18.0 18.0 20.0 2.0 1.8 8.0 8.0 5.5 5.0 3.5 — 15.0 15.0 3.5 — 14.0 15.0 2.0 1.8 6.0 5.0 15.0 15.0 4.0 — 15.0 4.0 — 2.0 1.8 9.0 9.0 6.0

Gates Corporation

0.89 0.93 0.86 0.81 0.78 1.21 1.24 0.79 0.90 0.79 0.90 0.78 1.35 1.26 0.78 0.96 0.98 0.96 1.13 1.07 0.98 1.06 3.22 0.28 0.51 10.06 40.25 0.44 0.75 3.75 0.61 0.63 0.63 9.81 7.63 0.87 0.74 0.30 0.54 0.47 0.80 0.67 0.68 4.00 0.65 0.93 10.57 8.15 0.32 0.58 11.34 45.37 0.50

Max.

1 7/8

200 200 200 250 250 250 250 250 250 250 250 250 350 500 500 500 500 501 600 600 1000 1000 5000 10 15 18 18 20 75 75 80 85 90 100 100 106 150 10 15 20 75 75 75 75 80 100 100 100 10 15 18 18 20

Temp (°F) Min.

1 3/4

Hose O.D. (In.)

1 5/8

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Data Pages Suction (In. Hg.)

1 1/2

Name Stallion Stallion Stallion Crush Resistant 119B Plant Master 19B Plant Master 205MB Steam King 232MB Steam Queen Adapta Flex Black Cellar Master Duro Flex Food & Beverage Master Premo Flex LP350 (Butane-Propane) 18MB Air Drill 19B Plant Master 500 MP Air Drill 500 MP Air Drill Terminator Scorpion Scorpion X-Treme 1000 MP/Mine Spray 319MB Gold Master Powerbraid Plus (Slim Hole Rotary) 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) Fuel Fill (USCG Type A1 and B1) Fuel Fill (USCG Type A1 and B1) 4663K (Fuel Fill - Corrugated) 4684CF (Wet Exhaust - Corrugated) Engine Coolant (Wire Inserted - Hardwall) Engine Coolant (Silicone) Engine Coolant (Oil Resistant - Softwall) 75W (Standard Wall Coolant) Wet Exhaust (Hardwall) Wet Exhaust (Softwall) 76W (Heavy Wall Coolant) Steelhead 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) 4663K (Fuel Fill - Corrugated) 4684CF (Wet Exhaust - Corrugated) 75W (Standard Wall Coolant) Engine Coolant (Oil Resistant - Softwall) Engine Coolant (Wire Inserted - Hardwall) Engine Coolant (Silicone) 76W (Heavy Wall Coolant) Wet Exhaust (Hardwall) Wet Exhaust (Softwall) 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) Fuel Fill (USCG Type A1 and B1) Fuel Fill (USCG Type A1 and B1) 4663K (Fuel Fill - Corrugated)

Hose Finder Rated W.P. (psi)

Hose I.D. (In.)

Industrial Hose Products

-40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -30°F -40°F -22°F -22°F -40°F -40°F -40°F -40°F -40°F -40°F -30°F -30°F -40°F -40°F -40°F -40°F -40°F -65°F -40°F -40°F -40°F -40°F -40°F -40°F -30°F -30°F -40°F -40°F -40°F -40°F -40°F -65°F -40°F -40°F -40°F -30°F -30°F -40°F -40°F -40°F

+300°F +300°F +300°F +212°F +212°F +450°F +450°F +200°F +230°F +200°F +230°F +212°F +180°F +212°F +212°F +180°F +180°F +212°F +275°F +300°F +212°F +212°F +180°F +250°F +250°F +212°F +212°F +212°F +212°F +257°F +347°F +212°F +257°F +257°F +257°F +257°F +150°F +250°F +250°F +212°F +212°F +257°F +212°F +257°F +347°F +257°F +257°F +257°F +250°F +250°F +212°F +212°F +212°F

Hose Categories Acid-Chemical Acid-Chemical Acid-Chemical Air and Multi-Purpose Air and Multi-Purpose Steam Steam Air and Multi-Purpose Food and Beverage Air and Multi-Purpose Food and Beverage Air and Multi-Purpose Petroleum Transfer Mining Air and Multi-Purpose Mining Mining Air and Multi-Purpose Mining Mining Mining Air and Multi-Purpose Oilfield Air and Multi-Purpose Air and Multi-Purpose Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Water Air and Multi-Purpose Air and Multi-Purpose Marine Marine Marine Marine Marine Marine Marine Marine Marine Air and Multi-Purpose Air and Multi-Purpose Marine Marine Marine

Catalog Page No. 10 10 11 21 20 120 121 30 39 27 38 25 111 78 20 79 79 22 76 77 74 33 95 34 35 64 64 65 59 54 55 53 51 58 57 52 126 34 35 65 59 51 53 54 55 52 58 57 34 35 64 64 65

Hose Finder

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

C A P P P P C A P P P P P P D D A A U G A A C A C A C A C G G — G G G G D3 D C A D3 D P P C A P P P G G G G G G — G G MQ MQ G G P P C C2 P P P P D3 D P P D2 D3 C P P P S P P P P P C 2 C2 C A C A C C2 P D P D C2 C2 P D D D C A

Max.

Temp (°F) Min.

Hose Wt. (Lbs./Ft.)

2.31 2.33 2.25 2.30 2.38 2.24 2.19 2.35 2.19 2.43 2.25 2.40 2.40 2.25 2.41 2.44 2.44 2.37 2.39 2.44 2.77 2.39 2.42 2.46 2.49 2.16 2.36 2.36 2.39 2.38 2.50 2.50 2.48 2.36 2.32 2.94 2.58 2.75 2.60 2.36 2.50 2.54 2.32 2.60 2.52 2.52 2.52 2.33 2.41 2.57 2.46 2.48 2.44

Min. Bend Radius (In.)

20.0 20.0 — — 4.0 20.0 — — 3.0 — 15.0 20.0 20.0 30.0 28.0 28.0 28.0 28.0 20.0 20.0 30.0 — — 20.0 28.0 — 28.0 28.0 28.0 — — 3.0 30.0 20.0 — 5.0 30.0 30.0 30.0 30.0 30.0 30.0 — 30.0 30.0 30.0 30.0 — — — 30.0 — —

Cover Type

Hose O.D. (In.)

60 60 75 75 94 100 100 150 5 5 15 18 18 20 35 40 40 40 50 60 60 60 60 60 60 65 70 70 70 75 75 88 100 100 100 120 125 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150

Tube Type

Suction (In. Hg.)

Name 4684CF (Wet Exhaust - Corrugated) Engine Coolant (Wire Inserted - Hardwall) 75W (Standard Wall Coolant) Engine Coolant (Oil Resistant - Softwall) 1 7/8 76W (Heavy Wall Coolant) Wet Exhaust (Hardwall) Wet Exhaust (Softwall) Steelhead 63SB (Air & Vapor Duct) Master-Flex Vapor Recovery 163SB (Air & Vapor Duct - Heavy Duty) Fuel Fill (USCG Type A1 and B1) Fuel Fill (USCG Type A1 and B1) 4663K (Fuel Fill - Corrugated) Master-Flex 400 Master-Flex 101CL Master-Flex 201CR Master-Flex 202SW 770SB 4684CF (Wet Exhaust - Corrugated) 688SB (Bulk Commodity) 75W (Standard Wall Coolant) Engine Coolant (Oil Resistant - Softwall) Engine Coolant (Wire Inserted - Hardwall) Master-Flex 300 EPDM Master-Flex 500 Master-Flex 100GR Master-Flex 101CL Master-Flex 200CL Engine Coolant (Silicone) 2 Tufflex Food 76W (Heavy Wall Coolant) Maverick Wet Exhaust (Hardwall) Wet Exhaust (Softwall) 429W (Sand Blast) Hot Air Blower 690SB (Bulk Commodity) 692SB (Bulk Commodity) Barracuda Cellar Master Light Colt Dolphin Food Master Lite Longhorn Longhorn Longhorn AF (Alternative Fuel-Corrugated) Marlin Marlin Sani-Pure Shark Steelhead Steer

Rated W.P. (psi)

Hose I.D. (In.)

Data Pages

5.0 0.83 -40°F +212°F 4.5 4.25 -40°F +257°F — 0.72 -40°F +257°F — 0.73 -40°F +212°F — 0.98 -40°F +257°F 4.5 11.23 -40°F +257°F — 8.63 -40°F +257°F 15.0 0.88 -40°F +150°F 2.0 0.33 -30°F +250°F 2.0 0.48 -30°F +140°F 2.0 0.60 -30°F +250°F 9.5 12.03 -40°F +212°F 9.5 48.13 -40°F +212°F 7.0 0.53 -40°F +212°F 4.0 0.54 -30°F +140°F 4.0 0.57 -10°F +130°F 4.0 0.57 -10°F +130°F 4.0 0.58 -10°F +130°F 8.0 0.75 -40°F +150°F 5.0 0.88 -40°F +212°F 16.0 1.65 -40°F +150°F — 0.76 -40°F +257°F — 0.77 -40°F +212°F 5.0 4.75 -40°F +257°F 9.0 0.69 -30°F +140°F — 0.21 +25°F +120°F 6.0 0.66 -10°F +130°F 6.0 0.66 -10°F +130°F 6.0 0.71 -10°F +130°F — 0.73 -65°F +347°F — 0.95 -10°F +130°F — 1.04 -40°F +257°F 4.0 1.08 -40°F +180°F 5.0 11.90 -40°F +257°F — 9.18 -40°F +257°F 20.0 1.82 -40°F +150°F 9.0 1.13 -40°F +350°F 12.0 1.88 -40°F +150°F 12.0 1.46 -40°F +180°F 8.0 0.76 -40°F +180°F 12.0 0.96 -40°F +212°F 6.0 1.11 -40°F +250°F — 0.65 -40°F +180°F 6.0 1.50 -40°F +230°F 5.0 1.13 -40°F +180°F 6.0 1.12 -40°F +180°F 6.0 1.10 -30°F +180°F 20.0 0.65 -40°F +180°F 20.0 0.84 -40°F +180°F 24.0 1.25 -40°F +230°F 10.0 1.01 -40°F +180°F 20.0 0.93 -40°F +150°F — 0.93 -40°F +180°F

Hose Categories Marine Marine Marine Marine Marine Marine Marine Water Air and Multi-Purpose Petroleum Transfer Air and Multi-Purpose Marine Marine Marine Material Handling Water Food and Beverage Food and Beverage Material Handling Marine Material Handling Marine Marine Marine Material Handling Water Water Water Food and Beverage Marine Food and Beverage Marine Petroleum Transfer Marine Marine Material Handling Material Handling Food and Beverage Food and Beverage Water Food and Beverage Acid-Chemical Water Food and Beverage Petroleum Transfer Petroleum Transfer Petroleum Transfer Water Water Food and Beverage Water Water Petroleum Transfer

The world’s most trusted name in belts, hose and hydraulics.

Catalog Page No. 59 54 51 53 52 58 57 126 34 109 35 64 64 65 73 131 48 49 70 59 68 51 53 54 72 129 130 131 47 55 50 52 100 58 57 71 69 44 45 125 40 16 128 41 97 97 98 127 127 42 124 126 99

167

2 1/4

2 3/8

168

C D B1 B2 K L K P K P K P L P T P T P P2 P2 P2 B1 S P S P S P D2 P C A C A A A C A C A A A C D3 C C2 C C4 A D3 J J B1 J P C2 A M A A A A A A A A C A P P P P C A MQ MQ P P P P A A A A C A C A P P P P C A MQ MQ P P P P P P A A A A

Max.

Temp (°F) Min.

2.47 2.56 2.47 2.54 2.54 2.63 2.50 2.55 2.58 2.66 2.66 2.62 2.62 2.62 2.70 2.66 2.78 2.86 2.70 2.84 2.71 2.50 2.50 2.64 2.77 2.62 2.62 2.45 2.46 2.63 2.80 2.31 2.40 2.56 2.58 2.51 2.55 2.51 2.49 2.45 2.44 2.50 2.50 2.69 2.71 2.64 2.67 2.63 2.74 2.63 2.57 2.56 2.63

Min. Bend Radius (In.) Hose Wt. (Lbs./Ft.)

30.0 4.0 30.0 30.0 30.0 20.0 30.0 30.0 20.0 10.0 10.0 30.0 30.0 30.0 10.0 10.0 30.0 10.0 10.0 30.0 10.0 15.0 15.0 10.0 15.0 — — 10.0 10.0 — — 3.0 15.0 20.0 20.0 — — — 20.0 — 3.0 15.0 30.0 20.0 20.0 — — — 1.0 20.0 — 3.0 15.0

Cover Type

150 200 200 200 200 200 200 200 200 250 250 250 250 250 300 300 300 350 400 400 400 500 500 501 600 600 600 1000 1000 3000 5000 5 10 55 55 60 60 75 100 100 5 10 20 55 55 60 60 75 88 100 100 5 10

Tube Type

Hose O.D. (In.)

2 1/8

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Data Pages Suction (In. Hg.)

Name Super-Vac 6B Dura Master Appaloosa Mustang Mustang Mustang Crush Resistant Renegade Stallion Stallion Crush Resistant 205MB Steam King 232MB Steam Queen Cellar Master Food & Beverage Master Food & Beverage Master Aquarius Potable Water Sea Horse (Fuel Transfer) Sea Horse HW (Fuel Transfer Suction/Discharge - Hardwall) LP350 (Butane-Propane) Sea Horse 400 (Fuel Transfer) Sea Horse 400 HW (Fuel Transfer Suction/Discharge - Hardwall) Trident 400 500 MP Air Drill 500 MP Air Drill Terminator 18MB Air Drill Scorpion Scorpion X-Treme 1000 MP/Mine Spray 319MB Gold Master Powerbraid Plus (Slim Hole Rotary) Powerbraid Plus (Slim Hole Rotary) 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) 4684CF (Wet Exhaust - Corrugated) Engine Coolant (Wire Inserted - Hardwall) 75W (Standard Wall Coolant) Engine Coolant (Oil Resistant - Softwall) Engine Coolant (Silicone) Wet Exhaust (Hardwall) Wet Exhaust (Softwall) 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) 4663K (Fuel Fill - Corrugated) 4684CF (Wet Exhaust - Corrugated) Engine Coolant (Wire Inserted - Hardwall) 75W (Standard Wall Coolant) Engine Coolant (Oil Resistant - Softwall) Engine Coolant (Silicone) 76W (Heavy Wall Coolant) Wet Exhaust (Hardwall) Wet Exhaust (Softwall) 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty)

Hose Finder Rated W.P. (psi)

Hose I.D. (In.)

Industrial Hose Products

4.0 0.99 -40°F +150°F 16.5 0.99 -22°F +158°F 9.0 0.97 -40°F +225°F 9.0 1.10 -40°F +250°F 9.0 1.11 -40°F +250°F 9.0 1.13 -40°F +250°F 9.0 0.99 -40°F +212°F 9.0 1.18 -40°F +300°F 9.0 1.09 -40°F +300°F 25.0 1.57 -40°F +450°F 25.0 1.64 -40°F +450°F 6.0 1.20 -40°F +230°F 6.0 1.19 -40°F +230°F 6.0 1.20 -40°F +230°F 14.0 1.46 -40°F +150°F 14.0 1.40 -40°F +180°F 10.0 1.87 -40°F +180°F 14.0 2.01 -40°F +180°F 17.0 1.51 -40°F +180°F 15.0 2.03 -40°F +180°F 16.0 1.50 -30°F +158°F 14.0 1.40 -22°F +180°F 14.0 1.43 -22°F +180°F 14.0 1.35 -40°F +212°F 14.0 1.99 -30°F +212°F 16.0 1.51 -40°F +275°F 16.0 1.46 -40°F +300°F 25.0 1.36 -40°F +212°F 25.0 1.48 -40°F +212°F 25.0 2.95 -40°F +180°F 25.0 4.72 -40°F +180°F 2.5 0.35 -30°F +250°F 2.5 0.74 -30°F +250°F 6.0 0.93 -40°F +212°F 5.5 5.05 -40°F +257°F — 0.79 -40°F +257°F — 0.82 -40°F +212°F — 0.77 -65°F +347°F 5.5 12.56 -40°F +257°F — 9.69 -40°F +257°F 2.5 0.37 -30°F +250°F 2.5 0.88 -30°F +250°F 8.0 0.54 -40°F +212°F 6.0 0.98 -40°F +212°F 6.0 5.30 -40°F +257°F — 0.84 -40°F +257°F — 0.85 -40°F +212°F — 0.81 -65°F +347°F — 1.15 -40°F +257°F 6.0 13.20 -40°F +257°F — 10.19 -40°F +257°F 2.5 0.39 -30°F +250°F 2.5 0.71 -30°F +250°F

Gates Corporation

Hose Categories Petroleum Transfer Air and Multi-Purpose Acid-Chemical Acid-Chemical Acid-Chemical Acid-Chemical Acid-Chemical Acid-Chemical Acid-Chemical Steam Steam Food and Beverage Food and Beverage Food and Beverage Food and Beverage Petroleum Transfer Petroleum Transfer Petroleum Transfer Petroleum Transfer Petroleum Transfer Petroleum Transfer Mining Mining Air and Multi-Purpose Mining Mining Mining Mining Air and Multi-Purpose Oilfield Oilfield Air and Multi-Purpose Air and Multi-Purpose Marine Marine Marine Marine Marine Marine Marine Air and Multi-Purpose Air and Multi-Purpose Marine Marine Marine Marine Marine Marine Marine Marine Marine Air and Multi-Purpose Air and Multi-Purpose

Catalog Page No. 101 26 14 12 12 13 15 10 11 120 121 39 38 38 43 105 106 111 103 104 107 79 79 22 78 76 77 74 33 95 95 34 35 59 54 51 53 55 58 57 34 35 65 59 54 51 53 55 52 58 57 34 35

Hose Finder

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

10.0 10.0 7.0 6.5 — — — — 6.5 — 2.5 2.5 12.0 5.0 5.0 4.0 7.0 9.0 6.5 11.0 — — — — 8.0 8.0 8.0 — 6.5 — 14.0 15.0 15.0 10.0 10.0 22.0 9.0 — 12.0 8.0 8.0 25.0 25.0 12.0 12.0 30.0 12.0 12.0 25.0 5.0 12.0 12.0 17.0

14.02 56.08 1.03 5.55 0.88 0.89 0.85 1.21 14.62 10.70 0.41 0.74 0.65 0.77 0.77 0.79 1.08 0.91 5.80 0.91 0.92 0.94 0.28 0.89 0.92 0.92 0.97 1.27 15.33 11.24 1.43 2.25 1.77 1.06 1.06 1.53 1.48 0.80 1.98 1.50 1.47 1.02 1.02 1.40 1.28 1.65 1.46 1.49 1.14 1.46 1.81 1.81 1.70

Max.

C A C A C A P P P P C A MQ MQ P P P P P P A A A A C A C G G G G G C A D3 D P P P G P P C A G G MQ MQ G G G — G G P P P P P P P P D2 D3 C P P P P P S P P P P P C 2 C2 C A C C2 P D P D K P L P C2 C2 P D T P D D C D S P S P C A

Temp (°F) Min.

Hose Wt. (Lbs./Ft.)

2.78 2.78 2.81 2.83 2.76 2.80 2.75 2.88 2.75 2.69 2.69 2.75 2.75 2.98 2.98 3.01 2.94 2.89 2.96 3.00 2.89 2.92 2.55 2.88 2.90 2.90 2.92 3.00 2.90 2.82 3.08 3.23 2.85 2.96 2.96 3.11 3.05 2.82 3.13 3.05 3.05 2.83 2.91 3.05 3.01 3.08 3.02 3.07 2.99 2.99 3.25 3.25 3.16

Min. Bend Radius (In.)

20.0 20.0 20.0 20.0 — — — — 20.0 — 3.0 15.0 30.0 28.0 28.0 28.0 20.0 20.0 20.0 28.0 — — — — 28.0 28.0 28.0 — 20.0 — 30.0 30.0 30.0 30.0 30.0 30.0 30.0 — 30.0 30.0 30.0 — — 30.0 30.0 — 30.0 30.0 — 30.0 30.0 30.0 10.0

Cover Type

Hose O.D. (In.)

18 18 50 50 60 60 65 81 100 100 5 10 20 35 40 40 50 50 50 50 60 60 60 65 65 65 65 75 100 100 110 125 125 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 250 250 300

Tube Type

Suction (In. Hg.)

Name Fuel Fill (USCG Type A1 and B1) Fuel Fill (USCG Type A1 and B1) 4684CF (Wet Exhaust - Corrugated) Engine Coolant (Wire Inserted - Hardwall) 75W (Standard Wall Coolant) 2 3/8 Engine Coolant (Oil Resistant - Softwall) Engine Coolant (Silicone) 76W (Heavy Wall Coolant) Wet Exhaust (Hardwall) Wet Exhaust (Softwall) 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) 4663K (Fuel Fill - Corrugated) Master-Flex 400 Master-Flex 201CR Master-Flex 202SW 4684CF (Wet Exhaust - Corrugated) 770SB Engine Coolant (Wire Inserted - Hardwall) Master-Flex 300 EPDM 75W (Standard Wall Coolant) Engine Coolant (Oil Resistant - Softwall) Master-Flex 500 Engine Coolant (Silicone) Master-Flex 100GR Master-Flex 101CL Master-Flex 200CL 76W (Heavy Wall Coolant) Wet Exhaust (Hardwall) Wet Exhaust (Softwall) Hot Air Blower 2 1/2 690SB (Bulk Commodity) 692SB (Bulk Commodity) Barracuda Barracuda Cellar Master Light Colt Dolphin Food Master Lite Longhorn Longhorn AF (Alternative Fuel-Corrugated) Marlin Marlin Mustang Renegade Sani-Pure Shark Stallion Steelhead Super-Vac Cellar Master Food & Beverage Master Sea Horse (Fuel Transfer)

Rated W.P. (psi)

Hose I.D. (In.)

Data Pages

-40°F -40°F -40°F -40°F -40°F -40°F -65°F -40°F -40°F -40°F -30°F -30°F -40°F -30°F -10°F -10°F -40°F -40°F -40°F -30°F -40°F -40°F +25°F -65°F -10°F -10°F -10°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -32°F -40°F -40°F -40°F -40°F -40°F -30°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F

+212°F +212°F +212°F +257°F +257°F +212°F +347°F +257°F +257°F +257°F +250°F +250°F +212°F +140°F +130°F +130°F +212°F +150°F +257°F +140°F +257°F +212°F +120°F +347°F +130°F +130°F +130°F +257°F +257°F +257°F +350°F +150°F +180°F +180°F +200°F +212°F +250°F +180°F +230°F +180°F +180°F +180°F +180°F +250°F +212°F +230°F +180°F +300°F +150°F +150°F +230°F +230°F +180°F

Hose Categories Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Air and Multi-Purpose Air and Multi-Purpose Marine Material Handling Food and Beverage Food and Beverage Marine Material Handling Marine Material Handling Marine Marine Water Marine Water Water Food and Beverage Marine Marine Marine Material Handling Food and Beverage Food and Beverage Water Water Food and Beverage Acid-Chemical Water Food and Beverage Petroleum Transfer Petroleum Transfer Water Water Acid-Chemical Acid-Chemical Food and Beverage Water Acid-Chemical Water Petroleum Transfer Food and Beverage Food and Beverage Petroleum Transfer

The world’s most trusted name in belts, hose and hydraulics.

Catalog Page No. 64 64 59 54 51 53 55 52 58 57 34 35 65 73 48 49 59 70 54 72 51 53 129 55 130 131 47 52 58 57 69 44 45 125 125 40 16 128 41 97 98 127 127 12 15 42 124 10 126 101 39 38 105

169

170

A A A D3 C D3 C C2 J J B1 J A C2 C A A A A A C A P P P P C A P P P P P P A A A A C A P P MQ MQ P P C A P P P P P P C A P P C A P P P P P P P P A A U G A A C A C G G — G G G G C A D3 D P P P P D3 D C A MQ MQ P G G — D3 D G G

Min. Bend Radius (In.) Hose Wt. (Lbs./Ft.)

Cover Type

3.20 3.46 3.14 3.14 3.12 3.12 3.34 3.38 2.81 2.88 3.06 3.08 3.02 3.05 3.13 3.02 2.95 2.94 3.00 3.19 3.21 3.13 3.14 3.17 3.25 3.22 3.09 3.31 3.33 3.30 3.26 3.38 3.42 3.23 3.19 3.54 3.25 3.27 3.87 3.54 3.54 3.05 3.44 3.47 3.43 3.39 3.39 3.42 3.38 3.60 3.44 3.81 3.44

Tube Type

10.0 10.0 10.0 10.0 — — 10.0 — 3.0 15.0 15.0 15.0 — — — 15.0 — 3.0 15.0 15.0 15.0 — — — — 15.0 — 15.0 15.0 — — — 15.0 — 3.0 — 7.0 30.0 28.0 28.0 28.0 28.0 15.0 — 15.0 — 20.0 — — 28.0 28.0 30.0 28.0

20.0 30.0 30.0 30.0 18.0 18.0 20.0 30.0 2.8 3.0 9.0 7.0 — — — 7.0 — 2.8 7.0 10.0 7.5 — — — — 7.5 — 11.0 9.0 — — — 8.0 — 3.0 3.0 10.0 — 6.0 6.0 6.0 6.0 12.0 36.0 9.0 — 10.0 — — 12.0 9.0 24.0 9.0

Gates Corporation

1.82 3.04 2.16 2.19 1.89 1.81 2.90 4.00 0.43 0.78 1.12 6.05 0.96 0.98 1.32 16.00 11.79 0.44 0.81 1.17 6.30 0.97 1.00 1.03 1.37 16.69 12.29 1.21 6.60 1.07 1.04 1.43 17.35 12.80 0.49 0.69 0.88 0.84 1.05 1.04 1.04 1.06 1.26 1.30 6.85 1.10 1.19 1.10 1.05 1.03 1.20 2.54 1.20

Max.

2 7/8

400 500 500 500 600 600 1000 2500 5 10 40 40 60 60 69 100 100 5 10 40 40 50 60 60 63 100 100 40 40 55 60 63 100 100 5 5 10 20 30 35 35 35 40 40 40 50 50 50 50 50 55 60 60

Temp (°F) Min.

2 3/4

Hose O.D. (In.)

2 5/8

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Data Pages Suction (In. Hg.)

2 1/2

Name Trident 400 18MB Air Drill 500 MP Air Drill 500 MP Air Drill Scorpion Scorpion X-Treme Longwall Mine Emulsion Powerbraid Plus (Slim Hole Rotary) 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) 4684CF (Wet Exhaust - Corrugated) Engine Coolant (Wire Inserted - Hardwall) 75W (Standard Wall Coolant) Engine Coolant (Oil Resistant - Softwall) 76W (Heavy Wall Coolant) Wet Exhaust (Hardwall) Wet Exhaust (Softwall) 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) 4684CF (Wet Exhaust - Corrugated) Engine Coolant (Wire Inserted - Hardwall) Engine Coolant (Silicone) 75W (Standard Wall Coolant) Engine Coolant (Oil Resistant - Softwall) 76W (Heavy Wall Coolant) Wet Exhaust (Hardwall) Wet Exhaust (Softwall) 4684CF (Wet Exhaust - Corrugated) Engine Coolant (Wire Inserted - Hardwall) Engine Coolant (Oil Resistant - Softwall) 75W (Standard Wall Coolant) 76W (Heavy Wall Coolant) Wet Exhaust (Hardwall) Wet Exhaust (Softwall) 63SB (Air & Vapor Duct) Master-Flex Vapor Recovery 163SB (Air & Vapor Duct - Heavy Duty) 4663K (Fuel Fill - Corrugated) Master-Flex 400 Master-Flex 101CL Master-Flex 201CR Master-Flex 202SW 4684CF (Wet Exhaust - Corrugated) 609W (Dry Cement Delivery) Engine Coolant (Wire Inserted - Hardwall) 75W (Standard Wall Coolant) 770SB Engine Coolant (Oil Resistant - Softwall) Engine Coolant (Silicone) Master-Flex 300 EPDM Master-Flex 101CL 688SB (Bulk Commodity) Master-Flex 100GR

Hose Finder Rated W.P. (psi)

Hose I.D. (In.)

Industrial Hose Products

-30°F -30°F -22°F -22°F -40°F -40°F -40°F -40°F -30°F -30°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -30°F -30°F -40°F -40°F -65°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -30°F -30°F -30°F -40°F -30°F -10°F -10°F -10°F -40°F -40°F -40°F -40°F -40°F -40°F -65°F -30°F -10°F -40°F -10°F

+158°F +212°F +180°F +180°F +275°F +300°F +212°F +180°F +250°F +250°F +212°F +257°F +257°F +212°F +257°F +257°F +257°F +250°F +250°F +212°F +257°F +347°F +257°F +212°F +257°F +257°F +257°F +212°F +257°F +212°F +257°F +257°F +257°F +257°F +250°F +140°F +250°F +212°F +140°F +130°F +130°F +130°F +212°F +150°F +257°F +257°F +150°F +212°F +347°F +140°F +130°F +150°F +130°F

Hose Categories Petroleum Transfer Mining Mining Mining Mining Mining Mining Oilfield Air and Multi-Purpose Air and Multi-Purpose Marine Marine Marine Marine Marine Marine Marine Air and Multi-Purpose Air and Multi-Purpose Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Marine Air and Multi-Purpose Petroleum Transfer Air and Multi-Purpose Marine Material Handling Water Food and Beverage Food and Beverage Marine Material Handling Marine Marine Material Handling Marine Marine Material Handling Water Material Handling Water

Catalog Page No. 107 78 79 79 76 77 75 95 34 35 59 54 51 53 52 58 57 34 35 59 54 55 51 53 52 58 57 59 54 53 51 52 58 57 34 109 35 65 73 131 48 49 59 67 54 51 70 53 55 72 131 68 130

Hose Finder

Industrial Hose Products

G G G G P P C3 G D2 D3 P P C C2 P P P P C P K L P P S P P P P P C2 C2 C A C A C C2 P D P D K P K P L P C 2 C2 P D T P D D D D C A C D D2 P S P S P S P C A C A A A C A C A A A A D3 C D3 C C2 J J B1 J A C4 A C2 A C4 A C2 C A A A C A MQ MQ

Max.

Temp (°F) Min.

Hose Wt. (Lbs./Ft.)

3.46 3.17 3.50 3.76 3.75 3.64 3.50 3.54 3.36 3.52 3.51 3.54 3.75 3.60 3.36 3.63 3.58 3.58 3.53 3.33 3.41 3.58 3.58 3.53 3.58 3.58 3.59 3.49 3.49 3.45 3.52 3.70 3.86 3.86 3.86 3.70 3.86 3.88 3.67 4.00 3.71 3.97 3.67 3.67 3.64 3.77 3.91 3.91 3.91 3.91 3.90 3.35 3.67 3.63

Min. Bend Radius (In.)

28.0 — — 28.0 30.0 30.0 30.0 15.0 — 30.0 30.0 30.0 30.0 30.0 — 30.0 30.0 30.0 30.0 — — 30.0 30.0 30.0 — 30.0 30.0 — — — 30.0 10.0 30.0 30.0 30.0 10.0 30.0 10.0 10.0 30.0 10.0 10.0 10.0 10.0 — — 10.0 10.0 10.0 10.0 — 7.0 — —

Cover Type

Hose O.D. (In.)

60 60 63 65 100 100 100 100 100 125 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 200 250 250 250 300 300 350 400 400 400 500 500 500 600 600 1000 1000 1000 1000 2000 10 35 40

Tube Type

Suction (In. Hg.)

3 1/8 3 1/4 3 1/4

Name Master-Flex 200CL Master-Flex 500 76W (Heavy Wall Coolant) Master-Flex Fuel Delivery 690SB (Bulk Commodity) Hot Air Blower Maverick Wet Exhaust (Hardwall) Wet Exhaust (Softwall) 692SB (Bulk Commodity) Appaloosa Barracuda Cellar Master Light Colt Dolphin Food Master Lite Longhorn Longhorn Longhorn AF (Alternative Fuel-Corrugated) Marlin Marlin Mustang Mustang Renegade Sani-Pure Shark Stallion Steelhead Steelhead Steer Super-Vac Aquarius Potable Water Cellar Master Food & Beverage Master Food & Beverage Master Sea Horse (Fuel Transfer) Sea Horse HW (Fuel Transfer Suction/Discharge - Hardwall) LP350 (Butane-Propane) Sea Horse 400 (Fuel Transfer) Sea Horse 400 HW (Fuel Transfer Suction/Discharge - Hardwall) Trident 400 18MB Air Drill 500 MP Air Drill 500 MP Air Drill Scorpion Scorpion X-Treme Longwall Mine Emulsion Longwall Mine Emulsion Longwall Mine Emulsion Longwall Mine Emulsion Powerbraid Plus (Slim Hole Rotary) 163SB (Air & Vapor Duct - Heavy Duty) Engine Coolant (Oil Resistant - Softwall) Engine Coolant (Silicone)

Rated W.P. (psi)

Data Pages

Hose I.D. (In.)

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

9.0 1.27 -10°F +130°F — 0.39 +25°F +120°F — 1.49 -40°F +257°F 6.0 1.71 -30°F +130°F 18.0 2.73 -40°F +150°F 18.0 1.89 -40°F +350°F 6.0 1.73 -40°F +180°F 9.0 19.41 -40°F +257°F — 14.45 -40°F +257°F 18.0 2.20 -40°F +180°F 18.0 1.58 -40°F +225°F 14.0 1.74 -40°F +180°F 20.0 2.13 -40°F +212°F 11.0 1.94 -40°F +250°F — 1.08 -40°F +180°F 18.0 2.35 -40°F +230°F 8.0 1.78 -40°F +180°F 9.0 1.90 -40°F +180°F 9.0 1.86 -30°F +180°F 36.0 1.21 -40°F +180°F 36.0 1.21 -40°F +180°F 18.0 1.79 -40°F +250°F 18.0 1.81 -40°F +250°F 18.0 1.63 -40°F +212°F 36.0 1.90 -40°F +230°F 15.0 2.01 -40°F +180°F 18.0 1.83 -40°F +300°F 36.0 1.35 -40°F +150°F 36.0 1.64 -40°F +150°F — 1.39 -40°F +180°F 6.0 1.76 -40°F +150°F 21.0 2.15 -40°F +150°F 18.0 2.46 -40°F +230°F 18.0 2.46 -40°F +230°F 18.0 2.47 -40°F +230°F 21.0 2.17 -40°F +180°F 18.0 3.14 -40°F +180°F 24.0 2.77 -40°F +180°F 22.0 2.14 -40°F +180°F 20.0 3.66 -40°F +180°F 24.0 2.23 -30°F +158°F 36.0 3.69 -30°F +212°F 36.0 2.73 -22°F +180°F 36.0 2.78 -22°F +180°F 20.0 2.46 -40°F +275°F 20.0 2.83 -40°F +300°F 20.0 4.05 -40°F +212°F 20.0 4.05 -40°F +212°F 20.0 4.05 -40°F +212°F 20.0 4.05 -40°F +212°F 36.0 4.33 -40°F +180°F 10.0 0.84 -30°F +250°F — 1.19 -40°F +212°F — 1.14 -65°F +347°F

Hose Categories Food and Beverage Water Marine Petroleum Transfer Food and Beverage Material Handling Petroleum Transfer Marine Marine Food and Beverage Acid-Chemical Water Food and Beverage Acid-Chemical Water Food and Beverage Petroleum Transfer Petroleum Transfer Petroleum Transfer Water Water Acid-Chemical Acid-Chemical Acid-Chemical Food and Beverage Water Acid-Chemical Water Water Petroleum Transfer Petroleum Transfer Food and Beverage Food and Beverage Food and Beverage Food and Beverage Petroleum Transfer Petroleum Transfer Petroleum Transfer Petroleum Transfer Petroleum Transfer Petroleum Transfer Mining Mining Mining Mining Mining Mining Mining Mining Mining Oilfield Air and Multi-Purpose Marine Marine

The world’s most trusted name in belts, hose and hydraulics.

Catalog Page No. 47 129 52 108 44 69 100 58 57 45 14 125 40 16 128 41 97 97 98 127 127 12 12 15 42 124 10 126 126 99 101 43 39 38 38 105 106 111 103 104 107 78 79 79 76 77 75 75 75 75 95 35 53 55

171

172

3.5 10.0 — — 17.0 — 12.0 — 21.0 12.0 — 42.0 42.0 4.0 — 4.0 4.0 12.0 — — 24.0 20.0 8.0 — 8.0 8.0 8.0 — 48.0 48.0 32.0 17.0 15.0 13.0 13.0 12.0 48.0 48.0 — 8.0 24.0 24.0 24.0 11.0 8.0 20.0 — 16.0 24.0 24.0 24.0 28.0

Gates Corporation

0.57 1.01 1.28 1.26 1.45 1.23 7.90 1.71 2.17 22.31 16.63 1.47 1.35 0.59 1.32 0.80 0.92 1.15 1.46 1.43 1.64 8.95 1.68 1.40 1.65 1.65 1.68 1.95 1.69 2.22 3.21 1.81 1.49 1.87 1.87 2.01 2.21 2.69 0.53 2.44 3.51 2.96 2.44 2.25 2.29 27.60 18.57 2.52 2.72 2.11 2.74 2.70

Max.

A A A A C A P P C A MQ MQ P P P P P P P P P P P D D D A A MQ MQ A A U G A A C A P P C A P P C G MQ MQ G — G G G G P P D3 D D2 D3 D3 D P G D3 D G G G — G G D3 D D3 D G G C3 G D2 D3 C P P P C C2 C D P P P P P P K P L P T P D2 P

Min. Bend Radius (In.) Hose Wt. (Lbs./Ft.)

3.69 3.75 3.92 3.89 4.06 3.88 3.93 4.00 4.14 4.04 3.86 3.91 3.99 3.81 4.13 4.19 4.56 4.25 4.42 4.39 4.44 4.43 4.65 4.38 4.65 4.65 4.54 4.50 4.47 4.56 4.77 4.69 4.39 4.52 4.52 4.56 4.61 4.73 4.20 4.79 4.71 4.55 4.64 4.50 4.52 4.54 4.36 4.60 4.69 4.53 4.66 4.70

Cover Type

3.0 7.0 — — 15.0 — 15.0 — 30.0 15.0 — — — 3.0 — 3.0 — 7.0 — — 10.0 10.0 28.0 — 28.0 28.0 28.0 — — — 30.0 28.0 20.0 28.0 28.0 28.0 — — — 28.0 30.0 30.0 30.0 30.0 30.0 10.0 — 30.0 30.0 30.0 30.0 10.0

Tube Type

5 10 10 20 35 35 35 50 85 100 100 150 150 5 35 5 5 10 10 12 30 30 30 35 35 35 35 38 40 40 45 45 50 50 50 50 60 60 60 65 75 75 75 100 100 100 100 125 125 125 125 150

Temp (°F) Min.

Hose O.D. (In.)

3 5/8 3 3/4

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Data Pages Suction (In. Hg.)

3 1/2

Name 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) Engine Coolant (Oil Resistant - Softwall) 75W (Standard Wall Coolant) 4684CF (Wet Exhaust - Corrugated) Engine Coolant (Silicone) Engine Coolant (Wire Inserted - Hardwall) 76W (Heavy Wall Coolant) Hot Air Blower Wet Exhaust (Hardwall) Wet Exhaust (Softwall) Marlin Steelhead 63SB (Air & Vapor Duct) Engine Coolant (Silicone) 63SB (Air & Vapor Duct) Master-Flex Vapor Recovery 163SB (Air & Vapor Duct - Heavy Duty) Engine Coolant (Oil Resistant - Softwall) 75W (Standard Wall Coolant) 4684CF (Wet Exhaust - Corrugated) Engine Coolant (Wire Inserted - Hardwall) Master-Flex 400 Engine Coolant (Silicone) Master-Flex 101CL Master-Flex 201CR Master-Flex 202SW 76W (Heavy Wall Coolant) 609W (Dry Cement Delivery) 610W (Bulk Commodity) 688SB (Bulk Commodity) Master-Flex 300 EPDM 770SB Master-Flex 100GR Master-Flex 101CL Master-Flex 200CL 609W (Dry Cement Delivery) 609W (Dry Cement Delivery) Master-Flex 500 Master-Flex Fuel Delivery 690SB (Bulk Commodity) 692SB (Bulk Commodity) Hot Air Blower Maverick Super-Vac Wet Exhaust (Hardwall) Wet Exhaust (Softwall) Colt Mustang Renegade Stallion Aquarius Potable Water

Hose Finder Rated W.P. (psi)

Hose I.D. (In.)

Industrial Hose Products

-30°F -30°F -40°F -40°F -40°F -65°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -30°F -65°F -30°F -30°F -30°F -40°F -40°F -40°F -40°F -30°F -65°F -10°F -10°F -10°F -40°F -40°F -40°F -40°F -30°F -40°F -10°F -10°F -10°F -40°F -40°F +25°F -30°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F

+250°F +250°F +212°F +257°F +212°F +347°F +257°F +257°F +350°F +257°F +257°F +180°F +150°F +250°F +347°F +250°F +140°F +250°F +212°F +257°F +212°F +257°F +140°F +347°F +130°F +130°F +130°F +257°F +150°F +150°F +150°F +140°F +150°F +130°F +130°F +130°F +150°F +150°F +120°F +130°F +150°F +180°F +350°F +180°F +150°F +257°F +257°F +250°F +250°F +212°F +300°F +150°F

Hose Categories Air and Multi-Purpose Air and Multi-Purpose Marine Marine Marine Marine Marine Marine Material Handling Marine Marine Water Water Air and Multi-Purpose Marine Air and Multi-Purpose Petroleum Transfer Air and Multi-Purpose Marine Marine Marine Marine Material Handling Marine Water Food and Beverage Food and Beverage Marine Material Handling Food and Beverage Material Handling Material Handling Material Handling Water Water Food and Beverage Material Handling Material Handling Water Petroleum Transfer Food and Beverage Food and Beverage Material Handling Petroleum Transfer Petroleum Transfer Marine Marine Acid-Chemical Acid-Chemical Acid-Chemical Acid-Chemical Food and Beverage

Catalog Page No. 34 35 53 51 59 55 54 52 69 58 57 127 126 34 55 34 109 35 53 51 59 54 73 55 131 48 49 52 67 46 68 72 70 130 131 47 67 67 129 108 44 45 69 100 101 58 57 16 12 15 10 43

Hose Finder

Industrial Hose Products

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Hose Wt. (Lbs./Ft.)

Min.

Max.

4.54 4.73 4.76 4.36 4.65 4.64 4.62 4.57 4.33 4.41 4.61 4.58 4.49 4.51 4.88 4.88 4.70 4.87 4.83 4.99 4.84 5.06 4.79 4.79 4.69 4.75 4.92 4.89 4.94 4.88 4.97 5.27 5.04 4.86 5.01 5.19 5.51 5.25 5.44 5.43 5.47 5.56 5.73 5.77 5.77 5.65 5.65 5.53 5.75 5.74 5.60 5.54 5.37

Min. Bend Radius (In.)

30.0 — 30.0 — 30.0 30.0 30.0 30.0 — — — 30.0 — — 30.0 30.0 10.0 30.0 10.0 30.0 10.0 10.0 — — 3.0 7.0 — — 5.0 — — 30.0 10.0 — — 3.0 — 6.0 5.0 5.0 — — 28.0 28.0 30.0 28.0 28.0 20.0 30.0 30.0 30.0 5.0 —

Cover Type

Hose O.D. (In.)

150 150 150 150 150 150 150 150 150 150 150 150 150 150 250 250 300 300 400 400 400 500 600 600 5 10 10 12 25 25 35 40 100 100 150 5 5 10 15 15 30 30 30 30 40 45 45 50 55 55 100 100 100

Temp (°F)

P P C A S P P P C2 C2 C A C A C C2 P D P D C2 C2 P D D D C A S P S P C A C A C A C A A A A D3 J J B1 J A A A A C A P P C A MQ MQ D3 D D3 D P P P P D D A A U G A A C A P P D3 D D2 D3 G — C G D3 D G G G — D3 D D2 D3 P P P D P P P P

18.0 — 28.0 — 24.0 11.0 12.0 12.0 48.0 48.0 48.0 20.0 48.0 — 36.0 36.0 28.0 24.0 30.0 25.0 32.0 47.6 25.0 25.6 5.0 12.0 — — 27.0 — 54.0 36.0 22.0 — 54.0 6.0 5.0 12.0 30.0 24.0 60.0 60.0 11.0 9.0 40.0 21.0 21.0 20.0 30.0 30.0 25.0 24.0 —

2.25 3.07 2.82 1.41 3.12 2.65 2.65 2.59 1.32 1.67 2.77 2.62 1.85 2.03 3.24 3.24 2.80 4.03 3.43 4.64 3.49 5.77 4.10 3.96 0.89 1.25 1.62 1.60 1.84 1.56 1.89 3.57 30.89 21.14 2.16 0.99 1.13 1.38 2.03 13.45 2.09 2.73 2.34 2.40 3.93 3.08 3.00 2.73 4.30 3.82 3.89 34.04 23.35

-40°F -40°F -40°F -40°F -40°F -40°F -40°F -30°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -30°F -30°F -40°F -40°F -30°F -30°F -40°F -40°F -40°F -65°F -40°F -40°F -40°F -40°F -40°F -30°F -30°F -30°F -40°F -40°F -40°F -40°F -10°F -30°F -40°F -10°F -10°F -40°F -40°F -40°F -40°F -40°F -40°F

+180°F +180°F +212°F +180°F +230°F +180°F +180°F +180°F +180°F +180°F +230°F +180°F +150°F +180°F +230°F +230°F +180°F +180°F +180°F +180°F +158°F +212°F +275°F +300°F +250°F +250°F +212°F +257°F +212°F +347°F +150°F +150°F +257°F +257°F +150°F +250°F +140°F +250°F +212°F +257°F +150°F +150°F +130°F +140°F +150°F +130°F +130°F +150°F +150°F +350°F +180°F +257°F +257°F

Tube Type

Suction (In. Hg.)

Name Barracuda Blender Transfer Cellar Master Light Dolphin Food Master Lite Longhorn Longhorn Longhorn AF (Alternative Fuel-Corrugated) Marlin Marlin Sani-Pure Shark 4 Steelhead Steer Cellar Master Food & Beverage Master Sea Horse (Fuel Transfer) Sea Horse HW (Fuel Transfer Suction/Discharge - Hardwall) Sea Horse 400 (Fuel Transfer) Sea Horse 400 HW (Fuel Transfer Suction/Discharge - Hardwall) Trident 400 18MB Air Drill Scorpion Scorpion X-Treme 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) Engine Coolant (Oil Resistant - Softwall) 75W (Standard Wall Coolant) 4684CF (Wet Exhaust - Corrugated) 4 1/2 Engine Coolant (Silicone) 609W (Dry Cement Delivery) 688SB (Bulk Commodity) Wet Exhaust (Hardwall) Wet Exhaust (Softwall) Steelhead 63SB (Air & Vapor Duct) Master-Flex Vapor Recovery 163SB (Air & Vapor Duct - Heavy Duty) 4684CF (Wet Exhaust - Corrugated) Engine Coolant (Wire Inserted - Hardwall) 609W (Dry Cement Delivery) 610W (Bulk Commodity) Master-Flex 101CL Master-Flex 400 5 688SB (Bulk Commodity) Master-Flex 100GR Master-Flex 101CL 770SB 690SB (Bulk Commodity) Hot Air Blower Shark Wet Exhaust (Hardwall) Wet Exhaust (Softwall)

Rated W.P. (psi)

Hose I.D. (In.)

Data Pages

Hose Categories Water Petroleum Transfer Food and Beverage Water Food and Beverage Petroleum Transfer Petroleum Transfer Petroleum Transfer Water Water Food and Beverage Water Water Petroleum Transfer Food and Beverage Food and Beverage Petroleum Transfer Petroleum Transfer Petroleum Transfer Petroleum Transfer Petroleum Transfer Mining Mining Mining Air and Multi-Purpose Air and Multi-Purpose Marine Marine Marine Marine Material Handling Material Handling Marine Marine Water Air and Multi-Purpose Petroleum Transfer Air and Multi-Purpose Marine Marine Material Handling Food and Beverage Water Material Handling Material Handling Water Water Material Handling Food and Beverage Material Handling Water Marine Marine

The world’s most trusted name in belts, hose and hydraulics.

Catalog Page No. 125 102 40 128 41 97 97 98 127 127 42 124 126 99 39 38 105 106 103 104 107 78 76 77 34 35 53 51 59 55 67 68 58 57 126 34 109 35 59 54 67 46 131 73 68 130 131 70 44 69 124 58 57

173

10 12

174

Min. Bend Radius (In.) Hose Wt. (Lbs./Ft.)

A D A A A P G A A P D D3 G — G D P G — G D3 P D D P D P P P P C2 A D D C2 D A D G G P P P

Suction (In. Hg.)

C P C A A P U A C P D3 D2 C G P D3 P G G G D2 C D3 C P P P P P P C2 C P P C2 D C D3 C G P P P

— 60.0 35.0 6.0 12.0 — 6.0 15.0 36.0 — 72.0 72.0 12.0 15.0 27.0 48.0 36.0 24.0 24.0 — 36.0 36.0 24.0 18.0 28.0 30.0 — — 24.0 — 36.0 17.0 72.0 72.0 72.0 72.0 36.0 72.0 16.0 — 40.0 50.0 60.0

Gates Corporation

3.77 2.17 4.14 1.08 1.51 39.29 1.24 1.64 2.42 16.00 2.48 3.25 3.18 4.08 3.84 4.65 4.52 4.56 4.42 0.88 7.08 5.61 3.24 4.37 3.94 4.84 40.37 27.14 4.95 2.09 5.60 5.91 2.32 2.96 4.10 2.84 7.95 2.73 5.73 1.27 8.81 15.80 18.63

Max.

— 5.73 — 5.44 10.0 5.84 3.0 5.69 6.0 5.75 5.0 6.04 — 6.52 6.0 6.25 5.0 6.46 5.0 6.43 — 6.47 — 6.56 28.0 6.86 28.0 6.98 28.0 6.86 30.0 6.76 30.0 6.74 28.0 6.80 28.0 6.80 — 6.20 30.0 6.91 25.0 6.74 20.0 6.53 30.0 6.67 30.0 6.68 30.0 6.65 5.0 6.68 — 6.38 30.0 6.78 — 6.38 30.0 6.74 30.0 6.87 — 6.40 — 6.49 — 6.64 — 6.51 30.0 7.07 — 7.10 28.0 9.10 — 8.16 30.0 9.00 30.0 11.27 30.0 13.27

Temp (°F) Min.

6 5/8

Cover Type

150 150 300 5 10 100 5 8 15 15 25 25 25 35 35 40 40 45 45 45 50 50 50 60 100 100 100 100 125 125 150 150 150 150 150 150 200 20 25 45 100 100 100

Tube Type

5 1/2

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Data Pages Hose O.D. (In.)

Name Blender Transfer Marlin Sea Horse (Fuel Transfer) 63SB (Air & Vapor Duct) 163SB (Air & Vapor Duct - Heavy Duty) Wet Exhaust (Hardwall) Master-Flex Vapor Recovery 163SB (Air & Vapor Duct - Heavy Duty) 4684CF (Wet Exhaust - Corrugated) Engine Coolant (Wire Inserted - Hardwall) 609W (Dry Cement Delivery) 610W (Bulk Commodity) Master-Flex 400 Master-Flex 101CL Master-Flex 300 EPDM 688SB (Bulk Commodity) Hot Air Blower Master-Flex 100GR Master-Flex 101CL Master-Flex 500 690SB (Bulk Commodity) 692SB (Bulk Commodity) 770SB Super-Vac Barracuda Shark Wet Exhaust (Hardwall) Wet Exhaust (Softwall) Colt Dolphin Food Master Lite Longhorn Marlin Marlin Sani-Pure Steelhead Sea Horse HW (Fuel Transfer Suction/Discharge - Hardwall) 609W (Dry Cement Delivery) Master-Flex 400 Master-Flex 500 Barracuda Barracuda Barracuda

Hose Finder Rated W.P. (psi)

Hose I.D. (In.)

Industrial Hose Products

-40°F -40°F -40°F -30°F -30°F -40°F -30°F -30°F -40°F -40°F -40°F -40°F -30°F -10°F -30°F -40°F -40°F -10°F -10°F +25°F -40°F -40°F -40°F -40°F -32°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -40°F -30°F +25°F -32°F -32°F -32°F

+180°F +180°F +180°F +250°F +250°F +257°F +140°F +250°F +212°F +257°F +150°F +150°F +140°F +130°F +140°F +150°F +350°F +130°F +130°F +120°F +150°F +180°F +150°F +150°F +200°F +180°F +257°F +257°F +250°F +180°F +230°F +180°F +180°F +180°F +230°F +150°F +180°F +150°F +140°F +120°F +200°F +200°F +200°F

Hose Categories Petroleum Transfer Water Petroleum Transfer Air and Multi-Purpose Air and Multi-Purpose Marine Petroleum Transfer Air and Multi-Purpose Marine Marine Material Handling Food and Beverage Material Handling Water Material Handling Material Handling Material Handling Water Water Water Food and Beverage Food and Beverage Material Handling Petroleum Transfer Water Water Marine Marine Acid-Chemical Water Food and Beverage Petroleum Transfer Water Water Food and Beverage Water Petroleum Transfer Material Handling Material Handling Water Water Water Water

Catalog Page No. 102 127 105 34 35 58 109 35 59 54 67 46 73 131 72 68 69 130 131 129 44 45 70 101 125 124 58 57 16 128 41 97 127 127 42 126 106 67 73 129 125 125 125

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Chemical Resistance Table

The Chemical Resistance Table was compiled for use as a guide in selecting the most satisfactory hose tube and cover stocks for specific chemical applications. The data included are the best available to us at this time and will be revised as additional test information is obtained. It is always advisable to test rubber stocks under actual application conditions whenever possible. We recognize that much of the material contained in this resistance table must be, to a degree, general in nature. Factors such as method of compounding, temperature, chemical concentrations, conditions of exposure, etc., can appreciably affect polymer behavior. For certain applications, hoses designed for these applications must be used; therefore, the choice of tube stocks is restricted. These applications are: Steam

—

Hose from the Steam Hose line

Edible Products

—

FDA, 3A, USDA

Concentrated Chemicals

—

Hose from the Acid-Chemical Hose line

L.P Gas

—

LP Gas Hose only

Gasoline and Petroleum Products

—

Hoses from the Petroleum Transfer Hose line

Hydraulic

—

Hoses from Hydraulic Products Catalog

The nature of certain chemicals is such that Gates cannot offer a suitable hose to handle them. Many of the common chemicals are included in the Chemical Resistance Table. If they are not listed, please contact Hose/Connectors Product Application, Denver.

NOTE:

Before using a Gates hose to convey a chemical not listed in this Chemical Resistance Table, contact Denver Product Application for a recommendation. Phone (303) 744-5070.

Hose Selection Procedure: 1.

with a 1 or 2 rating. For continuous contact applications make note of tube materials with a 1 rating only.

Identify the…

Size of Hose required. Temperature of material being conveyed and environmental temperature. Application conditions/requirements such as vibration, flexing, abrasion. Material Being Conveyed Pressure of operation and maximum obtainable in the system including “spikes” and pump/valve ratings. 2.

Use the Industrial Hose Catalog, Industrial Hose Finder, or Hydraulic Hose Catalog to select hoses that have satisfactory working pressure ratings.

Verify maximum and minimum operating temperatures.

Select the hose that has the best chemical resistance rating (i.e. 1 is Preferred, 2 is Acceptable).

Select the proper coupling for the hose chosen from the Industrial Hose Catalog.

Locate the material being conveyed in the chemical resistance chart and identify potential tube materials: For intermittent contact or transfer service, make note of all tube materials

NOTE:

For Gates Acid/Chemical Hose, permanent style Couplings must be used for service temperatures above 125ºF (52ºC).

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 175

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

LISTING OF GATES HOSE STOCK TYPES Stock Type

Composition

Polychloroprene (Neoprene)

Similar to Type A except it is white and is used primarily for edible products

B1 B2

Proprietary for special applications. Contact Denver Hose Product Application

Acrylonitrile Butadiene (NBR)

A blend of Type C and plastic. Used primarily as hose cover material

Modification to Nitrile tube

Modification of Nitrile with excellent abrasion, tearing and gouging resistance (cover)

Natural Rubber (NR) and Styrene Butadiene (SBR)

Similar to Type D, except it is white and compounded to handle food products

Natural Rubber

PolyVinyl Chloride (PVC)

Modified PVC

Isobutylene and Isoprene (Butyl)

Chlorinated Polyethylene (CPE)

Specially compounded Cross-Linked Polyethylene (Gatron )

Ultra High Molecular Weight Polyethylene Ethylene (UHMWPE)

Chlorosulfonated Polyethylene (Hypalon )

Silicone Rubber

Ethylene, Propylene Diene (EPDM)

Special for Steam Hose applications

Specially Compounded Thermoplastic Vulcanizate (Sanitron )

Fluorinated Polyethylene (Teflon or Neoflon )

Urethane

Fluorocarbon (FKM)

Polyamide Resins (Nylon)

™

NOTE: Tube and cover compounds with the same name or Gates Type can differ between hoses. Compounds are designed for specific hose application requirements. Refer to the hose product sheet for recommended applications and restrictions. Example: Petroleum Transfer Hose Longhorn (Type C Nitrile) has a different Nitrile tube compound than Fuel Line 4219G (Type C Nitrile). Please read and observe all warnings on the back of the front cover of this catalog.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 176

A2 B1 B2 C2 C3 C4 D2 D3 G1 MQ P2

PA Good Good to Excellent Excellent Excellent Excellent Excellent Good Excellent

Good to Excellent Excellent Good Excellent Excellent Excellent Good

Nylon

Polyamide Resins

Good

V FluoroCarbon Fluoroelastomer FKM Viton® Fluorel® FKM

White food grade Neoprene, complies with FDA (tube) Proprietary for special applications. Contact Denver Hose Product Application Modification of Nitrile with increased ozone resistance (tube and cover) Modification to Nitrile tube Modification of Nitrile with excellent abrasion, tearing and gouging resistance (cover) White food grade Natural Rubber, complies with FDA (tube) Natural Rubber Modified PVC Silicone Rubber Special for Steam Hose applications

Natural Ultra High Ethylene Isobutylene ChloroCross Polyvinyl Fluorinated PolyurePoly Acrylonitrile Rubber or Molecular Chlorinated Elastomer and Isosulfonated Propylene Linked Polyethylene thane Chloroprene Butadiene Styrene Chloride Polyethylene Weight Polyethylene Polyethylene Diene prene Polyethylene Butadiene (plasticized) ® Gum Neoflon Common Name or Buna-N Rubber, or ™ PVC Butyl CPE Gatron Trade Name Neoprene Nitrile UHMWPE Hypalon® EPDM Urethane Buna-S Teflon® ASTM CR NBR NR or SBR — IIR CM XLPE UHPE CSM EPDM FEP EU Fair Fair Good to Physical Strength Good Good Excellent Good Good Very Good Good Very Good Excellent to Good to Good Excellent RESISTANCE TO: Good Fair Good Fair Good Excellent Good Good Excellent Good Excellent Excellent Abrasion to Excellent to Good to Excellent to Good to Excellent Good Poor Fair Weather/Ozone Poor Excellent Excellent Good Excellent Good Excellent Excellent Excellent to Excellent to Fair to Good Good Good Fair Fair Gas Permeation Good Good Good Excellent Good Good Excellent Excellent to Excellent to Excellent to Good to Good Good Good Petroleum Oils Excellent Excellent Poor Poor Good Excellent Excellent Poor Excellent Good to Excellent to Excellent Fair Gasolines Excellent Poor Fair Poor Good Excellent Excellent Fair Poor Excellent Fair to Good Good Good High Temperatures Good Fair Poor Excellent Excellent Good Fair Excellent Excellent Fair To Excellent to Excellent Fair Fair Fair Fair Low Temperatures Good Poor Good Good Fair Good Excellent to Good to Good to Good Fair to Good

GATES TYPE

These ratings are for normal or usual range of the specified compounds. Many are also modified to meet the needs of specific applications. See notes below.

CHARACTERISTICS AND RESISTANCE INFORMATION FOR HOSE TUBE AND COVER COMPOUNDS

Industrial Hose Products 39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 177

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Gates Chemical Rating System

as paint must be conveyed through a hose that has very good non-discoloring characteristics. If the product is not visually affected, then the hose is satisfactory. For some products, the discoloration may be objectionable from a visual standpoint. Also, the concentration of the particles causing the discoloration may be objectionable if they affect the final use of the product.

NOTE: Ratings are for the effect on the polymer only. "1" Preferred: Constant Contact — This chemical is expected to have minor or no effect on the Polymer. Hose approved for continuous contact. Environmental changes such as temperature, concentration, etc., may promote increased degradation.

"2" Acceptable: Intermittent Contact — This polymer should give reasonably satisfactory service. Due to the nature of this chemical, and under prolonged continuous exposure, the rubber may show minor to moderate deterioration and/or solution discoloration. Hose in-tended for transfer service only. Environmental changes such as temperature, concentration, etc., may promote increased degradation.

"X" Not Recommended — The polymer is

Some of the more common methods of checking discoloration are: 1.

Allowing the fluid to remain in a sample piece of hose for a specific period and expected operating temperature, then inspecting visually for discoloration.

Testing fluid as in No. 1 above and then passing it through filter paper to check foreign content.

A more refined test can be made with a spectrophotometer. This instrument measures light transmission through the fluid before and after immersion tests with rubber stocks. This gives a relative rating expressed in percent, the original fluid being rated at 100%.

unsatisfactory for this chemical and should not be used.

"-" (Dash) — Insufficient or no data available for this material. Testing is advised.

NOTE 1.

The above ratings as applied to the Chemical Resistance Table are intended as guides only. They are compiled from the best data available to us. Ratings shown in the table are based on 100% concentrated or saturated solutions, unless otherwise noted, and up to 100 F (+38°C), unless otherwise stated.

NOTE 2.

If unusual conditions exist, a polymer test in the fluid is suggested.

NOTE 3.

Where a chemical listed in the Resistance Table is soluble in a solvent other than water, the solvent should also be checked for its suitability with the polymer.

NOTE 4.

Discoloration of fluids conveyed in the hose. There are no generally accepted standard tests for measuring or rating discoloration of fluids passing through a hose. The amount of discoloration that can be tolerated is usually established by the user on the basis of application. Obviously, products such

If discoloration of the product becomes a serious problem for a specific application, contact Denver Product Application for a recommendation. Phone (303) 744-5070.

NOTE 5.

Fluid permeation through the tube wall needs to be considered. A tube material may show no sign of degradation, however hose failure can occur if material permeates through the tube to degrade adhesive layers or reinforcement.

Hose Coupling Material —

Gates recommends hose couplings made of six materials: Iron or Carbon Steel, 304SS, 316SS, Aluminum, Brass and Polypropylene. The Chemical Resistance Table includes columns showing the suitability of a specific coupling material for the chemicals listed. In most instances, at least one coupling material is rated for each chemical. For certain chemicals, other metallic alloys or plastics than those shown in the table are required. These are generally available from other coupling manufacturers, but are not stocked by Gates.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 178

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Neoprene

Butyl

Fluorocarbon

X X 1 2 1 1 1 1 2 X 2 X X 1 1 1 1 1 X 2 -

X X 2 2 1 1 X X 1 1 1 1 1 1 1 1 X X 1 -

X X X X X X X 1 1 1 1 1 X 1 2 1 X X 1 -

PVC

X X 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 -

Nylon

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 X X 2 X 1 X 2 2 X 1 2 X X 2 2 X 2 X 2 1 X 2 X 2 1 X 2 X X X X 2 X X X X X X X 2 X X X 2 X X X X 2 - X X 2 X X X X 2 - X X 2 X 2 2 2 2 X X X X 1 X X X 2 - X X 2 NO HOSE AVAILABLE - X X X - X X X 2 X X X X X X 2 2 X X X X 1 X 1 - 2 1 2 X 1 1 X X X 2 1 X X X X 1 1 1 1 1 1 1 X - 1 1 1 - 1 1 2 2 1 - 1 1 1 X X X X X X X X X X - 1 1 - 1 1 - 1 -

CPE

X 1 1 2 1 1 2 X 1 2 1 2 2 X 1 1 1

X 1 1 1 1 1 X X 1 2 1 1 2 1 2 1 1

Hypalon

Sanitron

EPDM

2 1 1 2 1 1 1 X X 1 1 1 X 2 2 2 1 1

™

UHMWPE

2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1

™

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Gatron

Liquid Colorless Liquid Colorless Liquid Liquid above 176°F(80°C ) Clear Colorless Liquid Clear Colorless Liquid Clear Colorless Liquid Clear Colorless Liquid Clear Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid In Alcohol or Ether Gas Colorless Liquid Colorless Liquid Colorless to Yellow Liquid Colorless Crystals Colorless Liquid Colorless Liquid Colorless Liquid Liquid Colorless Liquid White Crystals Liquid Colorless Gas Colorless Gas Colorless Gas Colorless Gas Liquid Colorless Crystals In Water Solutions Varies Powder Liquid Colorless Liquid Colorless to Yellow Liquid Colorless Liquid Colorless Liquid Powder Colorless Liquid White Crystals White Crystals

Teflon /Neoflon

Form (at room temperature unless otherwise stated)

1 X X X X X X X X X X X X 1 X X

2 X 2 2 X X 2 2 X 2 X 2 2 -

1 1 1 1 1 1 X 1 1 1 2 1 1 2 1 1 1

1 2 X X X X X 1 X 1 X -

X 2 X X X X X X X 1 X -

1 1 X 1 1 1 1 1 X 1 1 1 1 1 2 1 1 1 1 1 1 -

X X 1 1 X 1 X 1 -

X X 1 X 1 1 1 X 1 1 1 1 1 2 X -

1 1 X X X X X 1 X 1 1 -

X X X 1 X 2 X X 1 X X X X -

Polypropylene

Brass

Aluminum

Stainless Steel 316

Stainless Steel 304

SBR

NBR

Food & Bev. Mstr.

™

Renegade

T K ®

NOTE: Ratings are for the effect on the polymer only !

Absorption Oil Acetal Acetaldehyde Acetamide Acetic Acid (40% or less) Acetic Acid (56% or less) Acetic Acid (85% or less) Acetic Acid (Glacial - 99.4%) Acetic Acid, Anhydride Acetic Anhydride (Acetic Oxide) Acetic Ether (Ethyl Acetate) Acetic Oxide (Acetic Anhydride) Acetone (Dimethylketone) Acetone Cyanohydrin Acetonitrile (Methyl Cyanide) Acetophenone Acetyl Chloride Acetyl Oxide (Acetic Anhydride) Acetyl-P-Toluidine (In Ether or Alcohols) Acetylene Acetylene Dichloride (Dichloroethylene) Acetylene Tetrachloride (Tetrachloroethane) Acrolein (Hydroquinone Inhibited) Acrylamide Acrylates (HEA or HPA) Acrylic Acid Acrylic Acid (Glacial 97%) Acrylic Emulsion Acrylonitrile Adipic Acid (70°F) Aeroshell 7A, 17 Grease Air, 212°F (100°C) Air, 257°F (125°C) Air, 300°F (149°C) Air, Ambient Aircraft Hyd. Oil AA Alachlor (Lasso) Alkaline Liquid (NOS) Alkyaryl Polyether Alcohol Alkyd Resin (Thermosetting Polymer) Alkylaryl Sulfonate (Alkylbenzene Sulfonate) Allomalaic Acid (Fumaric Acid) Solution Allyl Alcohol Allyl Bromide Allyl Chloride Alpha Methylstyrene Alpha Olefin Sulfonate Alpha Picoline Alum (Aluminum Sulphate or Other) Alum, Potash (Aluminum Potassium Sulfate)

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Chemical A

Couplings / Adapters

G ates Hose / Polymers

Iron/Carbon Steel

Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

1 X X X 1 X 1 X 1 1 1 1 1 1 X X

1 2 2 2 2 2 2 2 1 2 1 2 1 1 1 1 1 1 1 1 1 X 2

1 2 2 2 2 2 2 1 2 1 2 1 1 1 1 1 1 1 1 2 2

1 1 2 2 2 1 2 1 2 1 1 1 1 X X

1 1 1 X X X X 1 X 1 X 1 1 1 X X

1 2 2 X X X X 2 X 2 2 X X 1 2 1 1

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 179

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

SBR

Neoprene

Butyl

Fluorocarbon

1 1 1 1 1 X 1 1 1 1 1 1

1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 1 1

PVC

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Nylon

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

- 1 - 1 - 1 1 X X X X X 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 1 X X 1 X X X 1 1 1 1 1 1 1 X X X X 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 - 1 2 2 2 2 2 2 2 2 2 2 1 NO HOSE AVAILABLE 1 1 1 1 1 1 1 1 2 1 - 1 1 X - 1 2 - 1 2 1 1 X 1 - 1 2 X 2 2 2 2 2 2 2 1 - 1 - 1 1 - 1 1 - 1 1 X X X 2 X - X - 1 1 1 1 1 1 - 1 - 1 2 1 1 1 1 1 1 1 -

CPE

X 1 1 1 1 1 1 1 1 1 2 2 2

EPDM

X 1 1 1 1 1 1 1 1 1 2

Hypalon

Sanitron

X X 1 1 1 1 1 1 1 1 1 1 1 1

™

1 X 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2

™

1 X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

UHMWPE

(at room temperature unless otherwise stated) Granular White Crystalline Powder White Powder Colorless Liquid White to Yellow Crystals White to Yellow Solution White to Yellow Crystals White Solution White Crystals In Hot Water In Mineral Acid or Caustic Soda In Cold Water In HCl or HNO3 (slightly soluble) Varies White Crystals In Water Liquid Varies White Plates (Solid) Varies Varies Purple Powder Colorless Viscous Liquid Liquid Gas or liquid Colorless Liquid Colorless Liquid Liquid above 167°F (75°C) In Water White Crystals Colorless Liquid Colorless to White Powder White Crystals Liquid White Crystals Colorless Liquid Colorless Liquid White powder Colorless Crystals Aggregate Aggregate Liquid Colorless crystal Solution in Water White Crystals or Powder Liquid Yellow Solution Gray to White Crystals Yellow Crystals Liquid In Water

1 1 1 1 1 1 1 1 1 1 X X X -

X 1 1 1 X -

X 1 1 1 1 1 1 1 1 1

X X X 1 1 1

X 1 X 1 X 1 1 2 -

2 1 1 1 2 2 1 X 1 1 1

1 1 1 2 1 1 1 1

1 1 1 1 1 1 1 1 1 1 1

1 2 X X 1 -

1 1 1 1 1 X 2 1 1 -

Polypropylene

Brass

Aluminum

Stainless Steel 316

Stainless Steel 304

NBR

Food & Bev. Mstr.

™

Renegade

Gatron

Aluminum Fluoride Aluminum Formate (Di & Tri In Water) Aluminum Hydroxide (Alumina Trihydrate) Aluminum Nitrate Aluminum Phosphate Solution Aluminum Salts Aluminum Sulfate Aluminum Sulfate Solution Aluminum Sulfate Solution (49.7% H2O) Amines (A class of Organic Compounds) Amines (Aromatic - IE P-Toluidine) Amines (Mixed) Amines (Primary, Secondary, Tertiary, Etc) Aminodiphenylamine Aminoethanol (Ethanolamine) Aminoethylethanolamine Ammonia (Anhydrous) Ammonia (Aqueous up to 30% NH3) Ammonia Liquor Ammoniated Fatty Acid (ie Ammonium Caprylate) Ammonium Acetate Ammonium Bicarbonate Ammonium Bisulfate (50%) Ammonium Carbonate Ammonium Chloride Ammonium Chloride Solution Ammonium Flouride Ammonium Hydroxide (16%, 20%, 26%, & 30%) Ammonium Hydroxide (up to 30% NH3) Ammonium Metaphosphate Ammonium Nitrate Ammonium Nitrate Fertilizer (20.5% N,or 33.5% N) Ammonium Nitrate Prills and Oil Ammonium Nitrate Solution (up to 83%) Ammonium Nitrite Ammonium Persulfate Ammonium Phosphate Ammonium Phosphate Solutions Ammonium Polysulfide Solution Ammonium Sulfate Ammonium Sulfide Ammonium Sulfide Solution (40-44% or less) Ammonium Thiocyanate (50-60% or less)

Teflon /Neoflon

Form

Aluminum Chlorohydrate Solution (Up to 50% )

T K ®

NOTE: Ratings are for the effect on the polymer only !

Chemical

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Alumina - Calcined (Conveyed Pneumatically) Alumina Trihydrate (Conveyed Pnuematically) Aluminum Acetate Aluminum Alkyl (ie Triethylaluminum) Aluminum Bromide Aluminum Chloride Solution Aluminum Chloride, Anhydrous

Couplings / Adapters

G ates Hose / Polymers

Iron/Carbon Steel

Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

X X X X X X X 1 1 2 2 1 1 1 1 1 X X 1 1 1 1

1 2 2 2 1 1 2 X X X 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1

1 2 2 2 1 1 2 2 2 2 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

X 2 2 2 X X X X X 2 2 2 2 X X X X X -

X X X X 1 X X X X 1 X X X X X X X X X X X X X X -

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 X 1 1 1 1 1 1

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 180

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Neoprene

Butyl

Fluorocarbon

G Polypropylene

Brass

Aluminum

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

SBR

NBR

Food & Bev. Mstr.

™

Renegade

T K

1 1 X 1 1 1 X X 1 X 1 X X X X 2 X X 2 X X -

X 1 2 2 X 2 1 1 2 1 X 2 1 2 1 1 1 1 1 1 1 1 1 -

1 1 1 1 1 1 1 1 1 1 X 1 1 1 1 1 1 X 1 X 1 1 1 1 1 1 1 1 1 1 -

1 1 1 1 1 1 1 1 1 1 X 1 1 1 1 1 1 X 1 X 1 1 1 1 1 1 1 1 1 1 1 -

X 1 2 2 2 1 1 1 1 2 2 1 1 1 1 1 -

1 1 X X X X X 1 1 X 2 1 1 1 1 1 1 1 1 1 -

X X X 1 1 2 2 1 2 1 1 1 X 2 2 2 X X X X X -

2 -

1 1

1 1 1

2 1

Sanitron

EPDM

2 X X X -

2 2 X X X X X -

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

2 1 1 2 1 1 1 1 1 1 1 2 1 2 1 1 2 2 X 2 2 1 1 1 1 2 2 1

X X 1 1 2 1 1 1 X 1 2 1 1 2 X X X X X X 1 1 1 1 1 2 1

1 1 1 X 2 2 1 1 X 1 X 2 2 X X X X X 2 X X 2 X X X

1 1 1 -

Hypalon

CPE

Nylon

PVC

UHMWPE 1 2 2 2 2 -

™

Gatron 1 2 2 1 1 2 X 2 2

™

1 1 1 1 1 1 1 1 1 1

Form (at room temperature unless otherwise stated) Colorless Liquid Colorless Liquid Colorless Liquid Straw to Purple Liquid Clear Straw Colored Liquid Colorless Liquid Clear Liquid White Crystals/Liquid > 73°F(23°C) Gas or Liquid Colorless Oily Liquid White Crystals Colorless Oily Liquid White Solid/Liquid > 108°F(42°C) Liquid Solid to Liquid Colorless to Reddish Brown Liquid Liquid White Powder Reddish-yellow Liquid White Crystal Colorless Liquid Fuming Yellow Liquid Colorless Gas Typically Colorless Liquids In Water In Acid Varies Varies Black Solid Black Liquid Black Liquid Black Liquid In Carbon Disulfide Brown Liquid Brown Liquid Brown Liquid Liquid Liquid Liquid Liquid

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

Chemical

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Amyl Acetate (Banana or Pearl Oil) Amyl Alcohol Amyl Chloride (Chloropentane) Amyl Chlorides (mixed) Amyl Chloronaphthalene Amyl Naphthalene Amyl Phenol Amylamine Amylbenzene (sec amylbenzene) Anethole (anise camphor) Anhydrous Ammonia (R 717) Aniline Aniline Dyes Aniline Hydrochloride Aniline Oil (Aniline) Animal Fat (Lard) Animal Gelatin Animal Grease, Inedible, Liquid Animal Oils Ant Oil (Furfural) Antifreeze (Glycol Base) Antimony Chloride (50%) Antimony Pentachloride Antimony Salts Aqua Ammonia (Ammonium Hydroxide) (30%) Aqua Regia (Nitrohydrochloric Acid) Argon, Compressed Aromatic Hydrocarbons Arsenic Acid Arsenic Trioxide Askarel (Transformer Oil) Asphalt Asphalt (Blown) Asphalt (Cut Back) Asphalt Emulsion Asphalt Paint Asphaltene ASTM Oil No. 1 ASTM Oil No. 2 ASTM Oil No. 3 ASTM Reference Fuel A ASTM Reference Fuel B ASTM Reference Fuel C ATF (Automatic Transmission Oil)

Couplings / Adapters

G ates Hose / Polymers

X 1 1 1 1 X 1 1

X 2 X X X X X

X 1 2 X X X

1 1 1 1 X

X 2 X X -

2 2 2 2 X X X 1 1 1 X 1 X 2 X X X X X X X X X X X X X

X X X X 2 2 2 2 2 2 X X X X X X X X X X X X X X X 2 - X X X 2 X X 2 X X X X X X NO HOSE AVAILABLE X X X X 2 X X X X 2 2 2 2 X 2 X X X X 2 1 X X 2 X 1 - 1 1 - X 2 X 1 - 2 X X X 2 X 1 1 1 1 1 2 2 1 2 2 2 2 2 X X X X X 1 1 1 1 1 2 X X X X - X X 2 2 X X 2 X X X X X X 2 X X X - 1 2 X X 2 X 2 X X X 2 X X 2 X 1 X X 1 X 1 X X 2 X 1 X X X X 1 X X 1 X 1 X X 2 X 2 X X X X 1 X

1 2 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

X X X X 2 2 1 1 X 1 X X X X X X 2 2 X 1 X X -

2 2 2 1 1 1 1 1 2 1 X 1 1 X X 1 1 1 1 2 2 1

X X 1 1 1 1 X X 1 1 1 X 2 2 1 1 1 1 1 1 1 -

X X -

1 X -

2 -

X -

1 -

B Baltic Types 100, 150, 200, 300, 500 Banvel (Ag Spray, Concentrated) Bardol B Barite (Natural Barium Sulfate)

Liquid Liquid Dark colored Liquid White to Yellowish Powder

X -

X 1

X -

X X -

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 181

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Couplings / Adapters

Butyl

Fluorocarbon

X 1 X 2 1 X X X X X X X X X X X X X X X 1 2 1 X X 1 X X X X X X X

1 1 1 1 1 1 X 1 X X X 1 X X X 1 X X X 1 X 1 1 X X X X 1 1 2 1 1 X X 1 X X X X X X X

1 1 1 1 X X X X X X X X X X X X 2 2 2 X 1 2 1 2 X 1 X X 2 X X

X 1 1 1 1 X 2 X 2 X 2 2 X X 1 2 X X X 2 2 X 1 1 1 X 1 1 X X X X X X X

1 1 1 1 X 1 X 1 1 1 X 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 X 1 1 1 X X 1 1 1 X

Polypropylene

Neoprene

1 1 1 X 1 1 X X 2 X X X X X X 2 X 2 2 2 X 1 1 1 1 X 1 X X 1 2 X

Brass

X 1 1 1 X 2 X X 2 2 X X 2 2 X X X 2 2 2 1 1 1 X 1 1 X X X X X X X X

Aluminum

SBR

1 1 1 2 X 1 2 X X 1 X X 1 1 1 1 1 X 1 1 X X X X X X X -

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

PVC

Nylon

CPE

Hypalon

NBR

EPDM

Food & Bev. Mstr.

X 1 1 2 X 1 X X 2 2 X X X 2 X X 2 2 X 1 1 X X 1 X X X X

X 1 1 1 2 X 1 2 X X 1 X 2 X 2 2 2 1 1 1 1 1 1 X X X 2

X 1 2 1 2 1 2 X 2 1 1 1 X 1 1 X X X 1 1 -

1 1 X 1 1 2 X X X X X X X X 1 X X X 1 1 X 1 1 1 1 2 2 1 X X X X X X -

2 X 2 1 X 1 X 1 1 X 1 1 1 1 1 1 2 2 1 1 1 1 1 2 X 1 1 2 1 1 1 -

1 1 1 1 1 1 X 1 1 1 1 1 2 2 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 -

1 1 1 1 1 1 X 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -

X 1 1 X 1 1 1 1 1 1 1 1 -

1 2 2 X 1 1 1 2 2 1 1 2 X 1 1 2 1 1 1 1 1

1 1 1 1 1 X X 1 X 1 X 1 X 1 1 1 1 1 1 1 1 X 1 X 1 -

1 1 1 1 1 2 1 1 1 X 2 1 2 2 X X 1 1 1 1 1 1 X X 1 2 -

UHMWPE

1 1 1 1 1 1 1 1 2 1 2 1 1 2 1 2 1 1 2 2 X 1 1 1 1 1 1 1 1 1 1 2 2 1 2

™

Gatron

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

™

Form (at room temperature Chemical unless otherwise stated) Barium Carbonate White Powder Barium Chloride Colorless Crystals Barium Hydroxide White Powder Barium Sulfate White to Yellowish Powder Barium Sulfide Yellowish Green to Gray Powder Basic Copper Arsenate Blue to Green Powder BBP (Butyl Benzyl Phthalate) Clear Oily Liquid Beer Yellow Liquid Beet Sugar Liquors Colorless Solution Bellows 80-20 Hydraulic Oil Liquid Benzaldehyde (Benzoic Aldehyde) Colorless to Yellow Liquid Benzene (Benzol) Colorless to Yellow Liquid Benzenesulfonic Acid Liquid above 151°F (66°C) Benzidine Paste Benzoic Acid White Crystals Benzoic Aldehyde (Benzaldehyde) Colorless to Yellow Liquid Benzol (Benzene) Colorless to Yellow Liquid Benzophenone White Powder Benzotrichloride Colorless to Yellow Liquid Benzyl Acetate Water White Liquid Benzyl Alcohol Water White Liquid Benzyl Alcohol, Photo Inhibited Water White Liquid Benzyl Benzoate Water White Liquid Benzyl Chloride Colorless Liquid Bicarbonate Of Soda White Powder Bio-Diesel (B100) Liquid below 125°F (52°C) Bio-Diesel (B100) Liquid 125°F (52°C) and above Bismuth Carbonate White Powder Bisphenol A White Flakes Bitumastic Liquid Black Liquor (RXN Product Pulpwood+NaOH) Black Alkaline Liquid Black Sulfate Liquor (See "Black Liquor") Black Alkaline Liquid Blast Furnace Gas (Cooled) Gas Bleach (Chlorinated Lime) White Powder (35-37% Cl) Bleach Liquor (Calcium Hypochlorite/H2O) Clear Solution Borax (Sodium Borate) White Crystals Bordeaux Mixture (Slaked Lime &Copper Sulfate) In Water Boric Acid White Powder or Colorless Scale Boric Oxide Colorless Powder Brake Fluid (Petroleum Base) Liquid Brake Fluid (Synthetic Base) Liquid Brine (Salt) Liquid Bromine Dark Reddish Brown Liquid Bromobenzene Colorless Liquid Bromochloroethane Colorless Liquid Bromochloromethane (Chlorobromomethane) Clear Liquid Bromotoluene Clear Liquid Bubble Bath Compounds Liquid Bunker Oil Liquid Butadiene (1,3) Gas Butanal (Butyraldehyde) Water White Liquid

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

Sanitron

T K

™

Renegade

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Stallion ® Mustang

G ates Hose / Polymers

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 182

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Couplings / Adapters

Neoprene

Butyl

Fluorocarbon

G Polypropylene

Brass

Aluminum

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

SBR

1 1 1 1 1 X 1 1 -

1 1 1 2 1 1 1 1 X -

1 1 1 1 1 1 1 1 1 1 -

1 1 1 1 1 1 1 1 1 -

1 1 1 1 1 1 1 1 1 2 -

1 X 1 X -

1 1 2 1 1 1 1 1 1 2 X 2

X 1 1 1 X X 2 -

X 1 1 2 1 1 2 2 1 2 X 1 -

2 1 1 1 1 1 1 1 1 1 1 1 -

X 2 1 1 X -

X 1 X 1 2 X 2 X -

1 1 1 1 1 1 1 1 1 -

Sanitron

EPDM

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 1 1 1 2 1 1 1 1 1 1 2 1 -

1 1 2 1 2 1 -

1 2 2 1 2 1 1 1 1 X 2 1 -

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2

1 1 X X

1 1 1 1 1 -

Hypalon

CPE

Nylon

PVC

UHMWPE 2

™

Gatron 1

™

Form (at room temperature Chemical unless otherwise stated) Butandiol (Butylene Glycol) Colorless Oily Liquid Butane (Gas) Colorless Gas Butane (Liquid) Liquid Butanol (Butyl Alcohol) Colorless Liquid Butter Yellow to white semi-Solid to Liquid Butter Oil (Use FDA Hose) Yellow to white Liquid Butyric Acid Colorless Liquid Butyl Carbitol (Diethylene Glycol Butyl Ether) Colorless Liquid Butyl Cellosolve (EG Monobutyl Ether) Colorless Liquid Butyl "OxitolTM" for EG Monobutyl Ether Colorless Liquid Butyl Acetate Colorless Liquid Butyl Acrylate Colorless Liquid Butyl Alcohol (Butanol) Colorless Liquid Butyl Aldehyde Water White Liquid Butyl Benzyl Phthalate (BBP) Clear Oily Liquid Butyl Chloride Colorless Liquid Butyl Ether Colorless Liquid Butyl Ethyl Ether (Ethyl-n-Butyl Ether) Liquid Butyl Formate Colorless Liquid Butyl Mercaptan (2-Methyl-2-Butanathiol) Liquid Butyl Methacrylate Colorless Liquid Butyl Stearate Colorless Liquid Butylamine Colorless Liquid Butylene Glycol (Butandiol) Colorless Oily Liquid Butyraldehyde (Butanal) Water White Liquid Butyric Acid Colorless Liquid Butyric Anhydride Water White Liquid

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

NBR

Food & Bev. Mstr.

T K

™

Renegade

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Stallion ® Mustang

G ates Hose / Polymers

1 2 2 1 1 X 1 2 X X X 1 -

USE LPG HOSE ONLY USE LPG HOSE ONLY 1 1 1 2 1 - X X 2 - 2 2 X 2 2 X X 2 2 X X X X 2 1 1 1 2 1 X - X X - X 1 2 X X 2 2 2 - X X X - X X - X X X 2 X X X X X X X X X X X X X X 1 -

1 1 1 X X 1 X X 1 X 1 1 X 1 X 1 -

2 X X 2 X X 2 X X X -

1 2 1 1 1 1 2 1 1 2 2 2 1 -

1 X 1 1 X 1 -

1 1 1 1 1 1 2 1 1 -

X 1 1 1 X 1 1 1 1 1 1 1 1 1 1 2 2 -

X 1 1 X 1 1 1 1 1 1 1 1 1 1 1 X -

X 1 1 1 1 1 1 1 1 1 1 1 2

1 1 1 1 1 1 1 1 1 1 1

1 1 X 1 X X

C Cadmium Acetate (Soluble in H2O & Alcohols) Cake Alum (Aluminum Sulfate) Cake Alum Solution (Al Sulphate up to 50%) Calcine Liquor (Radioactive Waste) Calcium Acetate Calcium Aluminate (Soluble in Acids) Calcium Aluminate (Tricalcium Aluminate) Calcium Arsenate Calcium Bisulfide (Calcium Hydrosulfide) Calcium Bisulfite (Calcium Hydrogen Sulfite) Calcium Bromide Solution Calcium Carbonate Calcium Carbonate Slurry Calcium Chlorate Calcium Chloride, Dry Calcium Chloride, Liquid (Not For Food) Calcium Chloride, Liquid, Food Grade 33% Calcium Hydrogen Sulfite (Calcium Bisulfite) Calcium Hydrosulfide (Calcium Bisulfide) Calcium Hydroxide (Hydrated or Slaked Lime) Calcium Hydroxide Solutions Calcium Hypochlorite

In Water or Alcohol White Crystals In Water In Water Solution Powder In Acid Crystals or Powder In Dilute Acid In Alcohol or Water Yellow Liquid In Water or Alcohol Solid White Powder Solid in H2O In Water or Alcohol White solid In Water or Alcohol In Water Yellow Liquid In Alcohol or Water Solid White Powder In Glycerol or Acids Solid White Crystals

2 2 2 1 1 2 1 1 2 2 1 X

X 1 2 1 1 2 2 1 1 2 1 1 1 2 2 1 X

1 X 1 1 1 1 1 1 1 1 1 1 1 X

1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 2

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 183

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Neoprene

Butyl

Fluorocarbon

1 X 1 X -

X X 1 -

X X X X X 2 1 -

PVC

1 1 1 1 -

Nylon

1 1 1 1 1 1 1

- X X X 2 2 2 1 2 1 1 1 1 1 - 1 2 2 1 2 - 1 1 - 1 1 1 1 2 1 2 1 X 1 2 2 1 1 2 2 1 2 - 1 X X X X X X X X X 2 X X X X 2 X X X X 2 1 1 1 1 1 1 2 2 1 2 2 X X X X 2 X X 2 X X X X X X 1 1 1 1 1 X X X X 1 1 X X 1 2 X 2 1 2 1 2 2 2 1 - 1 X 1 1 2 2 X X 1 1 1 1 1 - 1 2 X X X X X - X X X X X X - X X X NO HOSE AVAILABLE X X X X X X X X X X -

CPE

1 1 1 X 2 2 X 2 2 2 1 2 X 1 X 1 X 2 2 2 2 2 1 X X X X

EPDM

1 X 1 1 2 2 X 1 X 1 1 1 X X

Hypalon

Sanitron

X 1 1 2 1 1 1 X 1 X 1 1 1 X

™

UHMWPE

1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 2 2 2 1 X 1 1 1 2 1 1 1 2 1 X

™

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Gatron

Teflon /Neoflon

Form (at room temperature Chemical unless otherwise stated) Calcium Hypochlorite Solutions In Water or Alcohol Calcium Metasilicate (Calcium Silicate) White Powder Calcium Nitrate Solutions In Water, Alcohol, or Acetone Calcium Oxide (Lime; quick,unslaked) White to Gray Lumps Calcium Silicate (Calcium Metasilicate) White Powder Calcium Stearate White Powder Calcium Sulfate White Powder or Crystals Calcium Sulfide Yellow to Gray Powder Calcium Sulfite (Soluble In Sulfurous Acid) In Acid Caliche Liquors (Sodium Nitrate) In Water Camphene (Liquid above 115°F/46°C) Liquid above 115°F (46°C) Cane Sugar Liquors In Water Caproic Acid Colorless or Yellow Liquid Caprolactam White Flakes Caprolactam, Molten (Above 156°F/69°C) Liquid Caprylic Acid (Octanoic Acid) Colorless, Oily Liquid Carbamates Crystals Carbolic Acid Liquid above 109°F (43°C) Carbolic Acid (Phenol) White or Pink Crystals Carbolic Acid (Phenol, 82-95% in Creosols) Liquid Carbon Dioxide (Dry) Gas Carbon Dioxide (Wet) Gas with Water Vapor Carbon Disulfide Clear to Faint Yellow Liquid Carbon Monoxide Gas Carbon Tetrachloride (Pyrene) Colorless Liquid Carbonic Acid Liquid Carbonyl Chloride (Phosgene) Gas/ Liquid Casein (White amorphous solid) In Concentrated Acid Castor Oil Pale Yellow or Colorless Liquid Caustic Potash, Dry (Potassium Hydroxide) White pellets or flakes Caustic Potash, Liquid (up to 45%) Solution in Water Caustic Soda, Dry (Sodium Hydroxide) White beads or pellets Caustic Soda, Liquid (up to 73%) Solution in Water Cellosolve Acetate (Eg Ethyl Ether Acetate) Colorless Liquid Cellosolve Butyl (Eg Butyl Ether) Colorless Liquid Cellulose Solid, many forms Cement, Portland Gray Powder China-Wood Oil (Tung Oil) Yellow Oil Chlordane Colorless Viscous Liquid Chlorinated Napthalene (Chloronapthalene) Oily Liquid to Solid Chlorinated Solvents (ie Tetrchloroethane) Colorless Liquid Chlorine Gas Chlorine Liquid (Liquid @ 210 PSIG @ 120°F/(38°C ) Clear Amber Liquid Chlorine Trifluoride Pale Green Liquid Chlorine Water (3% Chlorine) Clear, yellowish Liquid Chloroacetic Acid (Monochloroacetic Acid) Powder or White Crystals Chloroacetic Acid (Under 100°F/38°C) Solid Chloroacetic Acid Solution In Water, Alcohol, Ether Chloroacetone Colorless Liquid Chloroacetyl Chloride Water White Liquid

1 1 1 1 2 1 1 1 2 1 1 2 1 1 1 1 1 1 1 1 1 1 2 X X X 1 1 1 1 1

2 2 1 2 1 1 1 X 1 X X X X 1 1 X 1 X 1 X 1 1 1 1 2 X X X

1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 X

X X X X 1 1 2 X 1 2 1 1

1 1 1 1 2 1 X X X 1 1 X 1 X X 1 1 X 1 X 1 1 2 2 X

1 1 1 1 1 X -

2 2 -

X X -

X X 1

Polypropylene

Brass

Aluminum

Stainless Steel 316

SBR

Food & Bev. Mstr.

NOTE: Ratings are for the effect on the polymer only !

NBR

Renegade

T K

™

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Stainless Steel 304

Couplings / Adapters

G ates Hose / Polymers

Iron/Carbon Steel

Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

1 1 1 1 1 1 X X X 1 1 2 1 X X 1 1 1 1 X -

X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 X X -

2 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 X X -

X 1 1 1 2 1 2 2 2 1 1 2 1 X 2 1 1 -

X 1 1 1 1 2 X X X 1 1 2 1 2 X 1 1 2 -

1 1 1 1 1 1 X 1 X 1 1 1 1 1 1 -

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 184

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Neoprene

Butyl

Fluorocarbon

2 2 -

X X X

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 X 1 1 1 1 1 1

1 2 1 X 1 1 X X 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 2 1 1 2 2

X 1 2 1 1 2 2 1 2 X 1 -

X 1 1 1 1 X 1 X X X 2 X 2 X 2 1 2 X 1 X -

PVC

2 2 2 2

Nylon

1 1 1 1 1 1 1

X X X X X 1 X X X X X X SPECIAL HOSE REQUIRED X X X X X X 1 X X X X X X 1 X X X X X X 1 X X NO HOSE AVAILABLE - X - X 2 X X X X X X 1 - 2 2 2 2 1 1 1 1 1 1 1 1 2 X X X X X 1 2 X X X X X 1 1 1 X X X X 1 1 X 1 2 X 2 2 1 2 1 X 2 X X 2 X 1 X 2 X X 2 X 1 - 2 X X 2 2 1 X X 1 2 1 2 X X X X 2 1 X X X X X X 1 - 2 2 1 - 2 2 2 2 2 1 2 2 2 2 2 2 1 1 1 2 2 1 1 1 2 1 2 2 1 2 1 - 1 - X 1 1 2 2 X X 2 2 1 2 2 2 2 2 2 2 2 2 - 1 1 - 2 X X X 2 1 - X X X X 2 1 X X X X X X 1 2 2 X X 1 1 X 1 X X 2 X 1 - 2 2 1 X 1 X X 2 X 1

CPE

X X

Hypalon

Sanitron

EPDM

™

UHMWPE

2 2

™

1 1 1

Gatron

Teflon /Neoflon

Form (at room temperature Chemical unless otherwise stated) Chloroaniline Amber Liquid Chlorobenzene (Phenyl Chloride) (Monochlorobenzene) Clear Liquid Chlorobromomethane (Bromochloromethane) Clear Liquid Chlorodifluoromethane (Freon 22) Gas Chloroethane (Ethylene Dichloride) Colorless Liquid Chloroform Colorless Liquid Chloronapthalene (Chlorinated Napthalene) Oily Liquid to Solid Chloropentane (n-amyl chloride) Colorless Liquid Chlorophenol In Benzene, Alcohol, Ether Chloropicrin Mixture Colorless Liquid Chloropropylene Oxide (Epichlorohydrin) Volatile Liquid Chlorosulfonic Acid Colorless to Light Yellow Liquid Chlorothene (TM for chlorinated solvents) Colorless Liquid Chlorotoluene Colorless Liquid Chlorox Colorless Liquid Chocolate Syrup Liquid Chrome Alum (Chromium Potassium Sulfate) In Water Chromic Acid (100%) Dark Red Crystals Chromic Acid (25% Solution or less) In Water Chromic Acid (50% Solution with water) In Water Chromic Acid (Chromium Trioxide) Purplish-Red Crystals Chromic Chloride In Water Chromium Trioxide (Chromic Acid) Purplish-Red Crystals Cider Liquid Cinene (Dipentene) Colorless Liquid Citgo FR Fuels Liquid Citric Acid Solution In Water Coal Gas (Coke Oven Gas, Max 120°F/49°C) Gas Coal Tar Black, viscous Liquid Coal Tar Pitch (Roofing) Liquid above 212°F (100°C) Cobalt Nickel Plating Solution Liquid Cocoa Butter (Theobroma Oil) Liquid above 95°F (35°C) Coconut Oil Liquid above 77°F (25°C) Cod Liver Oil Pale Yellow Liquid Coke Oven Gas (Under 300°F/149°C) Gas Copper Arsenate (Cupric Arsenate) In Dilute Acid Copper Chloride (Cupric Chloride) In Water Copper Cyanide (Cupric Cyanide) In Dilute Acids or Alkalies Copper Nitrate (Cupric Nitrate) In Water Copper Sulfate (Cupric Sulfate) In Water Copper Sulfide (Soluble in Nitric Acid) In Nitric Acid Corn Oil Pale Yellow Liquid Corn Syrup (Glucose Syrup) Clear Liquid Cottonseed Oil Liquid, several colors Creosote (high Napthalene/Anthracene) Liquid Cresol (Methyl Phenol) Liquid above 95°F (35°C) Cresylic Acid Liquid Crotonic Acid (Methylacrylic Acid) White Crystalline Solid Crude Oil (Crude Petroleum Oil) Liquid Crude Wax Liquid above 200°F (93°C) Cryolite (Greeland Spar) In Sulfuric Acid

X X

X X X -

X X -

X 2 -

X X X X -

X 2 1 2 2 1 X 2 2 X 2 2 2 2 1 1 1 X 2 2 X X X 2 X

X 1 1 1 1 2 2 2 1 1 2 2 1 1 2 -

1 1 1 X X X X X 1 X X X X X -

X 1 1 1 X X X X 1 X 2 2 1 1 X X 2 1 1 1 1 1 X 1 1 -

Polypropylene

Brass

Aluminum

Stainless Steel 316

SBR

Food & Bev. Mstr.

NOTE: Ratings are for the effect on the polymer only !

NBR

Renegade

T K

™

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Stainless Steel 304

Couplings / Adapters

G ates Hose / Polymers

Iron/Carbon Steel

Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

1 1 1 1 1 X X X X X X 1 1 1 1 1 X X X 1 1 1 2 2 1 1 1 1

1 1 1 1 1 1 2 X X X X X X 1 1 1 1 1 X 1 1 1 1 1 1 1 1 X 1 1 1

1 1 1 1 1 1 1 X 2 2 2 2 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 1 X X X X X 1 1 1 2 X 1 1 1 1 1 1 -

1 1 1 1 1 X X X X X X 1 1 X X X X 1 1 X 1 1 1

X X X X 1 X 1 1 1 1 1 2 1 1 1 1 1 X 1 2 2 1 1 X

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 185

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

G Polypropylene

Brass

Aluminum

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

PVC

Nylon

CPE

Hypalon

Fluorocarbon

Butyl

Food & Bev. Mstr.

™

Renegade

T K

2 2 1 2 X 2 2 1 X X X 1 X X X X -

1 1 1 1 1 1 1 1 1 1 1 X X 1 2 X 2 1

2 2 2 1 1 X 2 1 1 X 2 X X X X X -

2 2 1 1 1 1 1 1 2 2 -

X X 1 1

1 1 1 1 1 1 1 X X X X -

1 X X X 1 1 1 2 1 1 1

1 X 1 1 1 1 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 1 1 1 1 1 1

X X X 2 1 1

X X X X 1 1 1 X X 1 1 1

1 1 1 1 X 1 1 1 1 1 X 1 X -

2 X X X 1 X - X X X 1 - X X X 2 X - X X X 1 - 1 1 1 1 1 1 1 1 1 1 X X 2 1 - 2 2 2 2 1 X 1 - 1 X 1 X X X X 2 X X 2 2 2 X 1 1 1 1 1 - 1 1 1 X X X X 2 X X X X X 2 X X X X X 2 2 X X X X X X X X X X 2 1 X - 2 X X X X - X X 2 X X X X X 1 X X X X X 1 X X X X X 1 SPECIAL HOSE REQUIRED

X X 2 X 2 1 1 2 X 2 1 X X X X X X X X

2 1 1 1 1 1 2 1 2 X 2 X X X

1 1 1 1 1 1 1 -

X 1 1 1 1 2 1 X X 1 2 1 X X X X

2 1 2 1 1 X 1 1 1 -

1 1 1 1 1 1 1 2 1 1 1 1 1 -

1 1 1 1 1 1 1 1 1 1 1 1 1 -

1 1 1 1 X 1 1 1 -

1 1 1 1 1 1 1 1 1 1 1 1 -

1 1 1 1 1 1 1 2 2 -

Sanitron

EPDM

NBR

SBR

Neoprene

X -

2 1 2 X 2 2 1 X X X 1 X X -

2 2 1 1 1 1 1 2 2 1 2 2 X 2 2 X X -

2 2 2 2 2 X 2 2 1 X X X X X -

2 2 2 2 2 X 2 2 1 X X X X X X X -

2 2 1 1 2 X X 2 1 1 1 X 2 X 2 X -

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

2 1 1 2 1 X 1 1 1 1 1 1 1 1 2 2 2

2 1 1 1 -

X 1 1 1 X X X

X 1 1 1 X 1 2 1 1 2 1 X X X X X X

UHMWPE 1 -

™

Gatron 2 1 1 1 1 1 2 1 1 1 1 2 2 1 2 -

™

1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1

Form (at room temperature unless otherwise stated) Colorless Liquid In Dilute Acid In Water In Dilute Acids or Alkalies In Water In Water Liquid Liquid Liquid In Dilute Acids or Alkalies In Water In Water In Nitric Acid In Water Colorless Liquid Colorless, oily Liquid Colorless to yellow Liquid Colorless Liquid Colorless Liquid Colorless Liquid Water white Liquid Colorless Liquids Colorless Liquid

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

Chemical

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Cumene (Isopropyl Benzene) Cupric Arsenate (Copper Arsenate) Cupric Chloride (Copper Chloride) Cupric Cyanide (Copper Cyanide) Cupric Nitrate (Copper Nitrate) Cupric Sulfate (Copper Sulfate) Cutting Oil (Mineral Oil Base) Cutting Oil, Sulfur Base Cutting Oil, Water Soluble Cyanide, Copper (Cupric Cyanide) Cyanide, Mercuric Cyanide, Potassium Cyanide, Silver Cyanide, Sodium Cyclohexane Cyclohexanol Cyclohexanone Cyclohexylamine Cyclopentane Cyclopentanol Cyclopentanone Cymene Cymene (Isopropyltoluene)

Couplings / Adapters

G ates Hose / Polymers

D Decalin (TM for decahydronapthalene) Decanal (Decyl Aldehyde) Decanol (Decyl Alcohol) Decyl Aldehyde (n-decanal) Deicing Fluid (ethylene or propylene glycol) Denatured Alcohol Detergent Sol. (Sodium dodcylbenzenesulfonate) Developing Solutions (Hypos) Dextron Dextrin (Starch gum) Diacetone Diacetone Alcohol Diammonium Phosphate Diazinon Dibenzyl Ether Dibutyl Ether Dibutyl Phthalate Dibutylamine Dibutylsebacate Dichloroacetic Acid Dichloroaniline Dichlorobenzene (ortho) Dichlorobenzene (para) Dichlorobenzyl Chloride Dichlorodifluoromethane (Freon 12)

Colorless Liquid Colorless to yellow Liquid Colorless, water white Liquid Colorless to yellow Liquid Orange Liquid Colorless Liquid In Water Liquid Brown Liquid Yellow or White Powder Colorless Liquid Colorless Liquid In Water In Petroleum Solvents Colorless Liquid Colorless Liquid Colorless Oily Liquid Colorless Liquid Clear Colorless Liquid Colorless Liquid In Alcohol or Benzene Colorless Liquid White Crystals Colorless Liquid Gas, Liquid @ 140 PSIG @ 100°F (38°C)

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 186

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Couplings / Adapters

Butyl

Fluorocarbon

X X X X X X X X 2 X X X 1 X X X 1 X X 1 X X X X X X -

X X X X X X X X X X 2 X X X X X X X X X 1 X 1 X 1 X X X 2 X X X X -

X X X X X X 2 X X X X X 1 X X 1 X 1 X X X X X X -

X X X X X X X X 1 X 1 2 2 X 2 2 2 X 2 2 1 X 1 1 2 X 1 1 1 2 2 2 2 -

2 1 1 2 1 2 X X X X 2 X 1 1 X X 1 1 1 1 1 X 1 X 1 X X X 1 X X 1 X X

Polypropylene

Neoprene

X X X X X X X 1 2 X X X X X X X X 1 1 X 2 X X 2 X X X X -

Brass

X X X X X X X X 2 X 2 X 1 X 2 2 1 1 1 1 1 1 1 1 1 1 1 X 1 1 X 2 1 X 1 2

Aluminum

SBR

X X X X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 X 1 X 1 1 1

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

PVC

Nylon

CPE

Hypalon

NBR

Food & Bev. Mstr. S

Sanitron

X X X X X X X X X 2 X X X X X X X X X X X X X X X X X -

X X X 1 1 2 2 2 2 2 1 1 1 2 1 2 -

X 1 X 1 1 1 1 1 1 1 -

X X X 2 2 X X X X 1 1 -

1 1 1 1 2 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 1 -

1 1 X X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -

X X 2 1 1 1 1 1 1 1 1

2 X X 2 1 2 1 1 2 1 -

UHMWPE

2 2 X 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1

™

Gatron

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

™

Form (at room temperature Chemical unless otherwise stated) Dichloroethane (Ethylene Dichloride) Colorless Oily Liquid Dichloroethyl Ether Colorless Liquid Dichloroethylene Colorless Liquid Dichloroethylene (Acetylene Dichloride) Colorless Liquid Dichloromethane (Methylene Chloride) Colorless Liquid Dichloropentane Light Yellow Liquid Dichloropropane (Propylene Dichloride) Colorless Liquid Dicyclohexylamine Colorless Liquid DIDA (Diisodecyl Adipate) Light Colored Oily Liquid Diesel Fuel Liquid Diethanolamine (20%) In Water or Alcohol Diethanolamine Liquid above 83°F (29°C) Diethyl Ether (Ethyl Ether) Colorless Liquid Diethyl Ketone Colorless Liquid Diethyl Oxalate Colorless Oily Liquid Diethyl Phthalate (Ethyl Phthalate) Water White Liquid Diethyl Sebacate Diethyl Sulfate Colorless Liquid Diethyl Sulfide (Ethyl Sulfide) Colorless Oily Liquid Diethylacetaldehyde (Ethylbutyraldehyde) Colorless Liquid Diethylamine Colorless Liquid Diethylbenzene Colorless Liquid Diethylene Dioxide (1,4 Dioxane) Colorless Liquid Diethylene Ether (Dioxane) Colorless Liquid Diethylene Glycol (Dihydroxydiethyl Ether) Colorless Syrupy Liquid Diethylene Glycol Methyl Ether (Methyl Cellosolve) Colorless Liquid Diethylene Glycol Monobutyl Ether Colorless Liquid Diethylene Glycol Monobutyl Ether Acetate Colorless Liquid Diethylene Glycol Monoethyl Ether Colorless Liquid Diethylene Glycol Monomethyl Ether Colorless Liquid Diethylene Glycol Monomethyl Ether Acetate Colorless Liquid Diethylenetriamine Yellow Liquid Dihydroxyacetone In Water Dihydroxydiethyl ether (Diethylene glycol) Colorless Syrupy Liquid Diisobutyl Ketone Colorless Liquid Diisobutyl Phenol (Octyl Phenol) White Flakes Diisobutyl Phthalate Liquid Diisobutylene Colorless Liquids Diisodecyl Adipate (DIDA) Light Colored Oily Liquid Diisooctyl Phthalate (DIOP) Nearly Colorless Liquid Diisopropanolamine Liquid above 108°F (42°C) Diisopropyl Ketone Colorless Liquid Diisopropylamine Colorless Liquid Diisopropylbenzene (meta) Colorless Liquid Diisopropylidene Acetone (Phorone) Yellow Liquid Dilauryl Ether Liquid above 92°F (33°C) Dimethyl Acetamide (DMAC) Colorless Liquid Dimethyl Aniline Yellow/brown Oily Liquid Dimethyl Ether Liquid under Pressure Dimethyl Formamide Water White Liquid

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

EPDM

T K

™

Renegade

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Stallion ® Mustang

G ates Hose / Polymers

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 187

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Food & Bev. Mstr.

CPE

Nylon

PVC

Iron/Carbon Steel

Stainless Steel 304

Stainless Steel 316

Aluminum

Brass

Polypropylene

Hypalon

Fluorocarbon

Butyl

Neoprene

SBR

NBR

EPDM

Sanitron

UHMWPE

Gatron

™

Renegade

T K

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 X 1 1 2 1 1 2 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 2 2 1 1 X 2 1 2 1 1 1 1 1

1 X 1 X 1 1 1 1 1 X 1 1 -

1 1 X 1 1 X 1 1 1 1 1 1 X 1 1 1 1 1 X X X X 1 1 1 1 -

2 X 2 X 1 2 X 1 X X 1 2 2 X 1 1 1 X 1 X X X X 1 2 1 1 1 X

X X X X 1 X X X X X X X 1 X X 1 X 1 1

X X X X 2 X X X X X X X X X -

X X X 2 X X X X X X X X X X -

X X X X 2 X X X X X X 1 X -

2 2 X X 1 2 X 2 1 2 2 X X X X 1 X

1 X 1 1 1 1 1 1 X X 1 1 1 X 1 1 1 1 X X X X 1 1 X 1 1 1 1 1 X 1 1 1 1 1 1 -

X X X 2 X X X X X X X 1 X -

1 X 1 1 2 X 2 2 X 2 1 -

1 X 1 1 1 1 1 1 X 1

1 X 2 X X X X X X 2

1 1 1 1 1 1 1 1 1 1 1 2 1

1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 1 1 1

1 2 1 1 1 1 1 1 1 1 1 1

1 1 2 X 1 1 1 1 -

™

Form (at room temperature unless otherwise stated) Colorless Oily Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Crystals Liquid @ 70 PSIG @ 120°F (49°C) Colorless Liquid Dark Red Liquid Colorless Liquid Colorless Liquid Water White Liquid Water white Liquid Colorless Liquid White solid, liquid @ 68°F (20°C) In Chloroform Liquid @ 50 PSIG @ 120°F (49°C) In Alcohol or Ether Light Colored Oily Liquid Colorless Liquid Light Colored Liquid Pale Straw Colored Liquid Water White Liquid Nearly Colorless Liquid Colorless Liquid Colorless Liquid Water White Liquid Colorless Liquid Yellow White Powder Colorless Liquid Water White Liquid Colorless Liquid Colorless Liquid Liquid Colorless or White Powder In Water Clear to Brown Liquid Water White to Straw Liquid Gas Colorless Liquid Colorless Liquid Water white Liquid Dark Red Liquid Liquid Straw Colored Liquid Gray, Pink or White Powder Liquid Liquid Colorless Liquid Liquid

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

Chemical

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Dimethyl Phthalate Dimethyl Sulfate (Methyl Sulfate) Dimethyl Sulfide Dimethyl Sulfoxide Dimethyl Terephthalate Dimethylamine (DMA) Dimethylaminoethanol (Dimethylethanolamine) Dimethylaminomethyl Phenol (DMP) Dimethylbenzene (DMB) Dimethylcarbinol (isopropyl alcohol) Dimethylcyclohexylamine Dimethylformamide (DMF) Dimethylketone (Acetone) Dimethylphenol (Xylenol) Dinitrobenzene (Soluble in Chloroform) Dinitrogen Tetroxide (Nitrogen Dioxide) Dinitrotoluene, Solid Dioctyl Adipate di (2-ethylhexyl) adipate Dioctyl Phosphite, di-(2-ethylhexyl) phosphite Dioctyl Phthalate, di-(2-ethylhexyl) phthalate Dioctyl Sebacate, di-(2-ethylhexyl) sebacate Dioctylamine di-(2-ethylhexyl)amine DIOP (Diisooctyl Phthalate) Dioxane (Diethylene Dioxide) Dioxane (Diethylene Ether) Dioxolane (Ethylene Glycol Formal) Dipentene (Cinene, Limonene) Diphenyl Phthalate Dipropyl Ketone Dipropylamine Dipropylene Glycol Dipropylene Glycol Monomethyl Ether (DPM) Dirco Oils Disodium Phosphate (DSP soluble in H2O) Disodium Phosphate Solution Distillate Fuel Oil Divinylbenzene (20-25% or 50-60% Grades) DMA (Dimethylamine) DMAC (Dimethyl Acetamide) DMB (Dimethylbenzene) DMF (Dimethylformamide) DMP (Dimethylaminomethyl phenol) Dodecylbenzene (Detergent Alkylate) Dodecylphenol Dolomite Dowtherm A (Biphenyl and Biphenyl Ether Mix.) Dowtherm SR-1 (Ethylene Glycol) DPM (Dipropylene Glycol Monomethyl Ether) Duro Oils

Couplings / Adapters

G ates Hose / Polymers

E EDB (Ethylene Dibromide)

Colorless Liquid

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 188

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Couplings / Adapters

Butyl

Fluorocarbon

X 1 2 X X X X X 1 X X X X X 2 X X 2 X X X -

X 1 2 X X X X X 1 X X X X X X X X X 2 X X X X 2 X X 1 X -

1 2 1 2 X X X X X 1 X X X X X X X X X X X 1 X X 1 1 X X 1 -

2 1 2 2 2 2 X X 1 X X X 2 X 2 X X X 2 X 2 X 2 2 X 1 1 2 X 1 -

1 1 1 X X 1 1 X X X X X X 1 2 1 1 1 X X 1 2 1 X 1 1 X 1 1 X 1 1 1 X 1 2 1 X -

Polypropylene

Neoprene

1 1 2 2 X X X X 1 X X 2 X X X X X X X X X X X X X X X 1 X X 1 1 X X 1 X X

Brass

1 1 X X 1 X 1 2 1 2 2 2 2 1 X X X X 2 2 X X X 2 2 X X 2 1 X 1 1 1 X X 1 1 1

Aluminum

SBR

1 X X X 1 1 1 2 2 2 1 1 1 1 1 1 2 X 1 1 1

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

PVC

Nylon

CPE

Hypalon

NBR

Food & Bev. Mstr. S

Sanitron

1 X 2 X X X X 1 X X 2 X X X X X X X X X 2 2 X 2 -

1 1 1 2 1 2 2 1 2 1 1 2 1 2 1 1 2 1 1 1 X 1 -

1 1 1 1 1 1 2 1 1 1 X X -

2 2 2 2 2 X X X 2 X X X 1 X X 1 1 X X X 1 -

1 1 1 1 1 1 1 1 1 1 2 2 1 2 2 1 1 1 2 1 -

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -

1 1 1 1 1 1 1 1 1 1 1 1 -

1 1 2 1 1 1 1 2 1 2 1 1 1 1 1 1 1 1 1 -

1 1 2 2 X X X 1 X 1 1 1 -

1 1 1 X X 1 2 X 1 1 1 2 1 -

UHMWPE

1 1 1 2 2 1 2 1 1 1 2 2 1 2 1 2 2 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 2 1 1 1

™

Gatron

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

™

Form (at room temperature Chemical unless otherwise stated) EDTA (Ethylenediaminetetraacetic Acid) Colorless Crystals Emulsion (Oil in Water) Water is Continuous Phase Enamels Liquid Epichlorohydrin (Chloropropylene Oxide) Volatile Liquid Epoxy Resin Solid Pellet Essential Oils Liquid Ethanol (Ethyl Alcohol) Colorless Liquid Ethanolamine (Aminoethanol) Colorless Viscous Liquid Ethers Liquids Ethyl Acetate (Acetic Ether) Colorless Liquid Ethyl Acetoacetate Colorless Liquid Ethyl Acrylate Colorless Liquid Ethyl Acrylate, Inhibited Colorless Liquid Ethyl Alcohol (Ethanol) Colorless Liquid Ethyl Aluminum Dichloride (Above 90°F/32°C) Clear Yellow Liquid Ethyl Bromide Colorless Liquid Ethyl Butyl Ether (Butyl Ethyl Ether) Liquid Ethyl Butyrate Colorless Liquid Ethyl Chloride Compressed Liquid Ethyl Chloroformate (Ethyl Chlorocarbonate) Water White Liquid Ethyl Ether (Diethyl Ether) Colorless Liquid Ethyl Ether Acetate (Cellosolve Acetate) Colorless Liquid Ethyl Formate Water White Liquid Ethyl Iodide Colorless Liquid Ethyl Isobutyrate Colorless Liquid Ethyl Mercaptan (Ethanethiol) Colorless Pungent Liquid Ethyl Methyl Ketone (MEK) Colorless Liquid Ethyl Oleate Light Yellowish Liquid Ethyl Oxalate Colorless Liquid Ethyl Pentachlorobenzene Ethyl Phthalate (Diethyl phthalate) Water White Liquid Ethyl Propionate Water White Liquid Ethyl Propyl Ketone (3-Hexanone) Colorless Liquid Ethyl Silicate Colorless Liquid Ethyl Sulfide (Diethyl Sulfide) Colorless Oily Liquid Ethylamine Colorless Liquid or Gas Ethylbenzene Colorless Liquid Ethylbutanol (2-Ethylbutyl Alcohol) Colorless Liquid Ethylbutyl Alcohol (Ethylbutanol) Colorless Liquid Ethylbutyl Amine Water White Liquid Ethylbutyl Ketone Clear Liquid Ethylbutyraldehyde (Diethylacetaldehyde) Colorless Liquid Ethylcellulose Granular Solid Ethylene Chlorohydrin Colorless Liquid Ethylene Cyanohydrin Straw Colored Liquid Ethylene Dibromide (EDB) Colorless Liquid Ethylene Dichloride (Chloroethane) Colorless Liquid Ethylene Glycol Colorless Liquid Ethylene Glycol Formal (Dioxolane) Water White Liquid Ethylene Glycol Monoethylether Colorless Liquid Ethylene Glycol Monoethylether Acetate Colorless Liquid

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

EPDM

T K

™

Renegade

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Stallion ® Mustang

G ates Hose / Polymers

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 189

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

G Polypropylene

Brass

Aluminum

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

PVC

Nylon

CPE

Hypalon

Fluorocarbon

Butyl

Food & Bev. Mstr.

™

Renegade

T K

2 1 1

X 1 1 X X 1

X -

1 1

1 1 1

1 X 1

1 -

2 X X 2 2 2 1 1 1 1 1 1 1 1 1 - 1 2 - 1 2 1 1 2 - 1 2 1 1 - 2 1 2 2 1 - 1 1 1 1 - 1 2 2 - 2 2 1 1 - 1 1 1 2 - 2 2 2 2 - 2 2 1 1 1 1 1 1 1 1 X 1 - 2 1 - 2 2 2 2 - 1 - 2 2 2 - 2 2 2 1 1 NO HOSE AVAILABLE 2 X - 2 X 1 1 1 2 X X 2 2 1 1 2 X X 2 2 1 - X X 2 - X X 1 2 X X 1 X - 1 SPECIAL HOSE REQUIRED SPECIAL HOSE REQUIRED

X 2 2 2 1 2 2 2 2 1 2 2 2 -

2 1 1 1 1 1 1 1 1 1 1 -

1 1 1 1 1 1 1 X

2 1 1 1 1 1 2 1 2 1 X X 1

2 2 2 2 -

1 1 1 1 -

X 1 1 1 X X -

X 1 1 X -

2 X X X X X X X X X 1 1 X X X -

1 X X 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 -

1 X X 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 -

1 X X X X X 1 1 1 2 2 -

2 X X X X 2 2 X 1 1 1 1 2 -

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -

Sanitron

EPDM

NBR

SBR

Neoprene

1 1 1 2 1

2 1 2 1 2 1 2 1 1

X X 1 1 X X 1

1 1

X -

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 X

2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -

2 1 1 1 1 1 1 1 1 1 X

2 1 1 1 X 1 -

2 1 1 1 2 2 2 1 X X 2 1 X

1 1 1 1 1 1 1

1 1 2 1 1 1 1 1

1 1 1 -

1 1 1 1 -

UHMWPE 1 1 1

™

Gatron 1 1 2 1 1 1 1 1 1 2 1

™

1 1 1 1 1 1 1 1 1 1 1

Form (at room temperature unless otherwise stated) Colorless Liquid Colorless Liquid Colorless Liquid Colorless Crystals Colorless Liquid Colorless Liquid Colorless Liquid Liquid Water White Liquid Liquid Colorless Liquid

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

Chemical

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Ethylene Glycol Monomethyl Ether Ethylene Glycol N-Butyl Ether Ethylenediamine Ethylenediaminetetraacetic acid (EDTA) Ethylhexaldehyde Ethylhexanediol Ethylhexanol (2-ethylhexyl alcohol) Ethylhexoic Acid Ethylhexyl Acetate Ethylhexyl Acrylate Ethylhexyl Alcohol (Ethylhexanol)

Couplings / Adapters

G ates Hose / Polymers

F Fatty Acid Fatty Alcohol, Blend Fatty Petroleum Alcohol Ferric Bromide Ferric Chloride Ferric Chloride solution Ferric Nitrate Ferric Nitrate Solution Ferric Sulfate Ferric Sulfate Solution Ferrous Acetate Solution Ferrous Chloride Ferrous Chloride, Solution Ferrous Nitrate Ferrous Sulfate Solution Fertilizer (Liquid Manure) Finishing Oil Fire-Resistant Hydra-Fluid (Texaco) Firtec 290, MF Fish Oil Fixing Solution (Photo) Flint Floor Wax (Temperature Dependent) Fluoboric Acid (48% Purity) Fluoboric Acid (up to 48%) Fluorine Fluorine (Liquid) Fluosilicic Acid (50%) Formaldehyde Formaldehyde Solution (up to 50%) Formalin (37-50% HCHO with 15% MeOH) Formamide Formic Acid FR Fluid D FR Hydraulic Fluid Freon 12 (Dichlorodifluoromethane) Freon 13

Solid, Semisolid or Liquid C8-11 Liquids, >C11 Solids C11 or Less are Liquids Red Crystals Black-Brown Solid Liquid Violet Crystals Liquid Yellow Crystals or Gray Powder Liquid Liquid in H2O or Alcohol Greenish-White Crystals Liquid Liquid Liquid Liquid Liquid Liquid Liquid Liquid Gray, Brownish, Black Varies Colorless Liquid Colorless Liquid Pale Yellow Gas Yellow Liquid Colorless Liquid Gas Liquid Liquid Colorless Oily Liquid Colorless Liquid (bp 100°C) Liquid Brown Liquid Gas or Liquid Gas or Liquid

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 190

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Butyl

Fluorocarbon

G Polypropylene

Neoprene

Brass

Aluminum

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

PVC

Nylon

CPE

SBR

NBR

Food & Bev. Mstr.

™

Renegade

T K

X X X X X X X 1 -

2 1 2 2 1 1 1 1 1

2 1 1 1 1 1 1 1 1 -

1 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 -

2 2 -

1 1 1 2 1 1 -

1 X 1 2 2 2 1 -

In Alcohol or Glycerol In Alcohol Solution Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Flakes or Powder Clear Colorless Liquid White Crystals Crystals or Powder Aqueous Solution Crystals to White Powder Liquid Varies Clear Viscous Liquid Clear Viscous Liquid Liquid above 80°F (27°C) Liquid Watery suspension Clear Colorless Liquid White Crystals Powdered, Flake, Crystals Semi-Solid Liquid Liquid

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 2 2 2 2 1 1 1 1 1 1 1 1 1 1

1 1 1 1 1 1 2 1 1 2 1 1 1

1 1 X X X X X 1 1 1 1 1 2 -

1 X X X X 2 1 1 X 1 1 1 1 1 X 1

X X 2 2 2 2 X 1 2 1 1 1 1 1 2

2 2 X X X X 1 1 X 1 1 1 X 1

2 2 X X X X 1 1 X 1 1 X 1 1 1 1 X 1

X X 2 2 2 2 X 1 2 1 1 1 2 1

2 2 X X X X X X 1 X 1 1 1 1 1 X 1

1 1 1 1 1 1 X 1 1 1 1 1 1 1 -

X X X X 2 1 1 1 1 1 2 1

1 1 1 X 1 1 1 2

X X 1 1 1 1 1 X 2 1 1 -

X X X X X X 1 X 1 1 1 1 1 1 -

X X 2 2 2 2 1 1 2 2 2 1 1 1 1

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 1 1 1 1 -

1 1 1 1 1 1 X 1 1 1 1 1 -

1 1 X X -

Oils to Waxy Solid Liquid Liquid Black to Brick Red

1 1 1 1

1 1 1 -

1 1 -

X X X -

X -

X 1

X -

1 1 1 -

1 1 -

Gatron

Hypalon

Sanitron

2 1 1 1 1 1 1 1 1 1 1 1

™

1 1 1 1 1 1 1 1 1 1 1 1

SPECIAL HOSE REQUIRED SPECIAL HOSE REQUIRED SPECIAL HOSE REQUIRED X 1 X X 2 X 1 2 - 2 2 1 2 1 2 2 1 X X X X X X X X X X 2 X 2 X X X X 2 X 1 X X X X X X 1 2 2 2 2 2 2 1 1 1 1 1 X 1 1 X 1 -

(at room temperature unless otherwise stated) Gas or Liquid Gas or Liquid Clear Liquid Liquid Water White to Brown Liquids Colorless Crystals Liquid Colorless to Brown Liquid Colorless to Reddish Brown Liquid Colorless to Brown Liquid Colorless to Brown Liquid Colorless to Reddish Brown Liquid Colorless Liquid -

EPDM

™

UHMWPE

Form

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

Chemical

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Freon 134a (HFC 134a) Freon 22 (Chlorodifluoromethane) Freon 23 Fruit Juices Fuel Oil (ASTM 1-6) Fumaric Acid Fumaric Acid Solution (Allomalaic Acid) Furan (Furfuran) Furfural (Ant Oil) Furfural Alcohol Furfuran (Furan) Furfuryl Alcohol Fusel Oil (Amyl Alcohol, Grain Oil) Fyrguard 150, 200 Fyrquel 15R&O, 220R&O, 550R&O Fyrquel 90, 150, 220, 300, 550, 1000

Couplings / Adapters

G ates Hose / Polymers

X 2 2 2 -

1 1 1 1 1 1 -

1 1 1 1 1 -

G Gallic Acid (3,4,5 Trihydroxybenzoic Acid) Gallic Acid Solution Gasohol (Gasoline blended with Ethanol) Gasoline (Oxygenated - Blended With MTBE) Gasoline (Unleaded Up to 50% Aromatics) Gasoline (White) Gelatin Glacial Acetic Acid Glacial Methacrylic Acid (GMAA) Glauber's Salt (Sodium Sulfate Decahydrate) Gluconic Acid (Commercial 50% Aqueous) Glucose Glucose Solution Glue Glycerine (Glycerol) Glycerol (Glycerine) Glycerol Monolaurate Glycol FR Fluids Glycol Slurry Glycols (ie Ethylene Glycol) GMAA (Glacial Methacrylic Acid) Graphite Grease Grease, Silicone Base Green Liquor (Effluent Alkaline Pulping) Green Sulfate Liquor

H Halowax (Chlorinated Hydrocarbons) HEA (2-Hydroxyethyl Acrylate) HEA Acid (2-Hydroxyethyl Acrylate) Hematite (Iron Ore) 1 Petroleum hose only.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 191

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Couplings / Adapters

Butyl

Fluorocarbon

X X 1 X X X X 1 X 2 X X X 2 2 2 2 -

X X 1 1 1 X 1 1 X X X X X 1 1 X 2 X X X 2 2 2 2 -

X 2 1 2 2 1 1 X 2 1 X X X X X X X -

X X 1 X X 2 X 2 X 1 1 X 1 1 X X X 1 X 1 1 X 2 2 2 X 2 2 2 2 -

1 1 1 1 1 1 1 1 X 1 1 1 X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 X X X 1 1 1 1 1

Polypropylene

Neoprene

2 1 1 1 1 X 2 1 X 2 1 X 1 1 1 1 1 1 1 1 X 1 1 1 X X X 1 X X X X -

Brass

X X X 1 X 1 X X X X X 1 1 1 1 X 1 X X X X 1 X 1 X 2 2 2 X X 1 2 X -

Aluminum

SBR

1 X X 1 X 1 X X X 1 1 1 1 1 1 -

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

PVC

Nylon

CPE

Hypalon

NBR

EPDM

Food & Bev. Mstr.

X 1 X X X X 1 2 X X X 2 2 2 2 -

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -

1 1 1 1 1 1 1 1 1 1 1 1 1 1 X X X X -

X 2 1 X 1 1 1 1 1 2 X X X 2 X X X X -

1 1 1 1 1 1 1 1 1 1 1 X 1 X 1 1 1 1 1 1 1 1 1 X X X

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 X X X

1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 X X X X X

1 1 1 2 1 2 1 1 1 1 1 X X 1 1 1 1 1 1 X X X

1 1 1 1 1 1 1 1 1 1 1 1 1 -

UHMWPE

1 2 2 1 1 1 X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -

™

Gatron

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

™

Form (at room temperature Chemical unless otherwise stated) HEP (2-Hydroxypropyl Acrylate) Liquid Heptachlor (In Xylene) Liquid Heptanal (Heptaldehyde) Colorless Oily Liquid Heptane Colorless Liquid Heptanedicarboxylic Acid (Azelaic Acid) Yellowish to White Powder Heptanoic Acid Clear Oily Liquid Heptanol Colorless Liquid Hexachlorocyclohexane White to Yellowish Flakes Hexachlorocyclopentadiene Yellow Liquid Hexadecanoic Acid (Palmitic Acid) White Crystals Hexahydrophthalic Anhydride Clear Colorless Viscous Liquid Hexaldehyde Colorless Liquid Hexamethylenediamine, Solution Colorless Flat Solid Leaflets Hexamethyleneimine Clear Colorless Liquid Hexane Colorless Liquid Hexanol (Hexyl Alcohol) Colorless Liquid Hexanone (Ethyl Propyl Ketone) Colorless Liquid Hexene Colorless Liquid Hexyl "Cellosolve" (EG monohexyl ether) Water White Liquid Hexyl Alcohol (Hexanol) Colorless Liquid Hexyl Methacrylate Liquid Hexylamine Water White Liquid Hexylene (1-Hexene) Colorless Liquid Hexylene Glycol Colorless Liquid Honey Yellow Liquid Houghto-Safe 1055, 1110, 1115, 1120, 1130 Liquid Houghto-Safe 271, 416, 520 & 616, 620 Liquid Houghto-Safe 5046 Liquid Houghto-Safe 625, 640 & 525 (Under 100°F/38°C) Liquid HPA Acid (2-Hydroxypropyl Acrylate) Liquid HPO (Sodium Thiosulfate) White Powder Hy-Chock Oil Liquid Hydrocyanic Acid (up to 98%) Water White Liquid Hydrafluid 760 (Texaco and Houghton) Liquid Hydrafluid AZR&O, A, B, AA, C Liquid Hydrasol A (Textile Dying) Hydraulic Fluid (Phosphate Ester Base) Liquid Hydraulic Fluid (Polyalphaolifin) Liquid Hydraulic Fluid (Std. Petroleum Oils) Liquid Hydraulic Fluid (Water Glycol Base) Liquid Hydraulic Fluid HF-18, HF-20 Liquid Hydraulic Fluid HF-31 Liquid Hydrazine Colorless Fuming Liquid Hydrazine Hydrate Colorless Fuming Liquid Hydrazine Solution Liquid Hydro-Drive Oil (Houghton) Liquid Hydrobromic Acid (62% and less) Colorless to Yellow Liquid Hydrobromic Acid (to 48%) Colorless to Yellow Liquid Hydrochloric Acid (15%) Colorless to Yellow Liquid Hydrochloric Acid (37%) Colorless to Yellow Liquid Hydrochloric Acid, anhydrous Colorless Fuming Gas

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

Sanitron

T K

™

Renegade

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Stallion ® Mustang

G ates Hose / Polymers

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 192

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Couplings / Adapters

Neoprene

Butyl

Fluorocarbon

G Polypropylene

Brass

Aluminum

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

CPE

SBR

NBR

Food & Bev. Mstr.

1 2 2 -

X X X X X X X 1 X X X X -

1 X X X X X X 1 2 2 2 2 1 1 -

1 X X X X X X 1 1 1 1 1 1 1 -

1 X X X X X 1 1 1 1 -

X X X X X X 1 X X X X -

X 1 1 1 1

2 1 1 X 1 X

2 1 1 X 1 1

1 1 1 X 1 1

2 1 1 X

1 1

1 1 1 1 1 1

1 2 1 1 1 1 1

1 1 1 1

PVC

1 1 1 1 1 2 1 1

- X 2 2 X 1 2 1 - 1 2 2 2 2 1 1 1 2 X X X 2 2 1 1 1 1 2 X X X 2 2 1 2 1 1 - X X X 2 X 1 2 1 1 X X X X X 1 2 2 X X X X X X 2 2 1 2 2 X X X X X 1 1 X CONTACT DENVER PRODUCT APPLICATION - 1 X X X X 1 1 - 1 - 2 X - 2 1 1 - 1 X X X 2 X X 1 2 X X 1 X 1 1 1 X 1 2 X X 1 X 1 1 1 X 2 X X X 2 1 1 1 - 2 X X X 2 1 1 NO HOSE AVAILABLE - 1 X X - 2 X X - 1 1 - 2 2 1 - X 2 X - X - X X X X 2 X - X X - X X 1 - 1 1 2 1 X 1 - 1 1 X 1 - 1 1 1 1 X 1 - 1 - 2 X X X X 2 X X 1 2 X X X X X 1 2 -

Nylon

1 1 1 1

1 2 2 -

Hypalon

1 1 1 X X X 1

Sanitron

UHMWPE

1 1 1 1 1 1 1 1

™

Gatron

(at room temperature Chemical unless otherwise stated) Hydrocyanic Acid (10% Solution with water) Water White Liquid 1 Water White Liquid below 77°F(25°C) 1 Hydrocyanic Acid (98% or less) Hydrocyanic Acid (up to 20%) Water White Liquid 1 Hydrofluoric Acid (38% or less) Colorless Liquid 1 Hydrofluoric Acid (47% or less) Colorless Liquid 1 Hydrofluoric Acid (53 % or less) Colorless Liquid 1 Hydrofluoric Acid (70%) iquid 1 Hydrofluoric Acid (Concentrated) Colorless LiquidColorless L 1 Hydrofluosilicic Acid In Water 1 Hydrogen (Gas) Gas Hydrogen Bromide Liquified (Anhydrous) Liquid 1 Hydrogen Bromide Solution (HydroBromic Acid) Liquid 1 Hydrogen Bromide, Anhydride Colorless Gas 1 Hydrogen Chloride Colorless Fuming Gas 1 Hydrogen Dioxide (Hydrogen Peroxide) Liquid 1 Hydrogen Fluoride Colorless Gas or Liquid 1 Hydrogen Peroxide (35% or less) Liquid 1 Hydrogen Peroxide (50% or less) Liquid 1 Hydrogen Peroxide (70% or less) Liquid 1 Hydrogen Peroxide (90% or less) Liquid 1 Hydrogen Sulfide Colorless Gas Hydrogen Sulfide, Liquified Liquid @ 410 PSI, 120°F (49°C) 1 Hydrolube (Water Glycol) Liquid 1 Hydrolubric Oil (Houghton) Liquid 1 Hydroquinone White Crystals 1 Hydroquinone Solution Liquid 1 Hydroxyacetic Acid Colorless Crystals Hydroxyacetic Acid Solution Liquid 1 Hydroxyethyl Acrylate (HEA) Liquid 1 Hydroxyethyl Acrylate Acid (HEA Acid) Liquid 1 Hydroxyethyl Methacrylate Clear Liquid 1 Hydroxyethyl Methacrylate Solution in Xylene Clear Liquid 1 Hydroxypropyl Acrylate Acid (HPA Acid) Liquid 1 Hylene (Toluene Diisocyanate) Yellow Liquid 1 Hypochlorous Acid (only in dilute solutions) Greenish-Yellow Aqueous Sol. 1

™

Form

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

EPDM

T K

™

Renegade

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Stallion ® Mustang

G ates Hose / Polymers

X X X X X X

X X 2 X X X X X X

1 2 X X

1 2 2 X

1 -

1 1 -

I Ink (Printers) Ink Oil Insulating Oil (Transformer) Iodine Iodine Solution Iodine, In Alcohol Iron Acetate Liquor (Black Liquor) Iron Hydroxide Iron Ore (Hematite) Iron Oxide (Black, Brown, Red or Yellow) Iron Oxide Slurry Iron Salts Iron Sulfate Solution (Ferric Sulfate) 1 Petroleum hose only.

Liquid Liquid Liquid Grayish Black Granules Liquid Liquid Black Liquid Brown precipitate Black to Brick Red Solid Slurry Liquid

1 1 1 1 1 1 1 1 1 1

1 1 1 -

X X 1 1 2 1 1 2

2 2 1 2 1 1 2

X X X X 2

X X 1 X X X 1 1 1 1 -

2 X 2 2 1 1 2

X X 2 1 1 2

X 1 1 1 1 1 1 1

X 2 1 1 2

1 2 1

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 193

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Neoprene

Butyl

Fluorocarbon

G Polypropylene

Brass

Aluminum

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

SBR

NBR

Food & Bev. Mstr.

™

Renegade

T K

2 2 X 2 X 2 X -

1 1 1 1 1 1 1 1 1

1 1 2 1 1 1 1 1

2 2 1 2 1 2 1 1

1 1 -

1 1 1 1 1

X X X X X

2 2 2

1 1 1

2 2 2

1 1 1

Sanitron

EPDM

2 2 X -

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 2 2 1 1 1 2 1 2 1 1 2 1 1 2 -

1 1 1 1 1 1 1 -

1 1 X X 1 1 1 1 X 2 X -

1 1 1 1 1 1

1 1 1 1

1 -

Hypalon

CPE

Nylon

PVC

UHMWPE -

™

Gatron 1 2 -

™

1 1 1 1 1 1 1 1

Form (at room temperature unless otherwise stated) Liquid Colorless Liquid Colorless Liquid Water White Liquid Colorless to Yellow Liquid Colorless Liquid Colorless Liquid Colorless Gas Liquid @ 98 PSIG, 120°F (49°C) Colorless Liquid Gas Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Gas Liquid @ 88 PSIG, 120°F (49°C) Colorless Liquid Water White to Yellow Liquid Colorless Liquid Viscous Liquid Clear Liquid Water White Liquid Colorless Liquid Water White Liquid Liquid above 106°F (41°C) Colorless Liquid Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

Chemical

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Iron Sulfide Solution (Ferrous Sulfide) Isoamyl Acetate Isoamyl Alcohol (Isobutyl Carbinol) Isoamyl Bromide Isoamyl Butyrate Isoamyl Chloride Isoamyl Ether Isoamyl Phthalate Isobutane Isobutane Liquid Isobutanol (Isobutyl Alcohol) Isobutene (Isobutylene) Isobutyl Acetate Isobutyl Alcohol (Isobutanol) Isobutyl Aldehyde (Isobutyraldehyde) Isobutyl Carbinol (Primary Isoamyl Alcohol) Isobutylamine Isobutylene (Isobutene) Isobutylene Liquid (Isobutene Liquid) Isobutyraldehyde (Isobutyl Aldehyde) Isocyanate (Toluene Diisocyanate) Isooctane Isooctyl Adipate Isooctyl Alcohol Isooctyl Thioglycolate Isopentane Isophorone Isophthaloyl Chloride Isopropanol (Isopropyl Alcohol) Isopropanolamine (MIPA) Isopropyl Acetate Isopropyl Alcohol (Isopropanol) Isopropyl Benzene (Cumene) Isopropyl Chloride Isopropyl Ether Isopropylamine Isopropylbenzene (Cumene) Isopropyltoluene (Cymene)

Couplings / Adapters

G ates Hose / Polymers

1 X 2 2 X 1 X X

X 2 X X X X

1 X X 1 2 2 X 2 X X 1 2 1 2 1 X -

X - X X X 2 - 2 2 2 X - X X X X - X X X - X X X - X 2 USE LPG HOSE ONLY 2 2 2 2 2 1 X X X - X X X 2 2 2 2 2 X - X X X 2 - 2 2 2 X - X 2 1 X X X - X X X X X X X X 1 X X 1 X 1 2 2 2 1 2 - 2 1 X X X X 2 1 2 2 2 1 X X X X 2 -

1 1 2 X 1 X 2 X 2 1 X 1 1 1 1 1 1 1 1 X 1 1 1 X 1 1

1 X X 1 X 2 X X X 1 2 X X 2 X -

1 1 2 1 1 2 2 -

1 1 1 1 1 1 1 1

X X X X X

1 1 X 1 1 1

X X X X X

2 X 2 X X

X X X X X

1 1 1 1 1 1

X X X X X

1 -

J Jet Fuel A and A1 Jet Fuel JP1 Jet Fuel JP10 (Tetrahydroxydicyclopentadiene) Jet Fuel JP4 Jet Fuel JP5 Jet Fuel JP8

Liquid Liquid Liquid Liquid Liquid Liquid

K Kaolin Clay White to Yellowish Powder Karo Syrup Yellow Liquid 2 Aircraft fueling hose only for fueling operations.

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 194

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Couplings / Adapters

Food & Bev. Mstr.

T K

™

Renegade

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Stallion ® Mustang

G ates Hose / Polymers

Nylon

PVC

Iron/Carbon Steel

Stainless Steel 304

Stainless Steel 316

Aluminum

Brass

Polypropylene

1 1 1 -

1 1 -

X 1 1 1 -

X 2 2 -

1 1 X -

X X -

X X 1

X 1 X -

X 2 -

1 X -

X X -

1 -

1 1 1 -

2 X -

1 1 -

1 1 1 -

1 1 -

1 1 1 1 1 Colorless to Yellow Syrupy Liquid 1 Liquid above 108°F (42°C) 1 Colorless to Yellow Liquid 1 Colorless Crystals 1 Liquid 1 White Powder Liquid above 75°F (24°C) 1 White Crystals Solution 1 White Crystals 1 Solution 1 Solution 1 White Powder White to Blue Powder Colorless Oily Liquid 1 Colorless Liquid 1 Light Brown Viscous Liquid-Solid 1 Clear Liquid 1 White to Gray Lumpy Solid Solution 1 Solution 1 White Powder Powder White Crystalline Powder Powder or Lumps Colorless Liquid 1 1 Colorless to Straw Colored Liquid 1 Yellow Amber to Brown Liquid 1 Liquid 1 White Crystals Solution X Liquid 1 Liquid 1 Liquid 1

1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 1 2 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 1 1 1 1 X 1 X X -

1 1 1 1 1 X 1 1 1 1 1 X 2 -

2 2 2 2 X 1 1 1 X X X 2 2 X X 2 2 X X

X X 1 2 1 1 2 1 2 2 X 1 X 2 X 2 2 2 2 1

X 2 X X 2 2 2 X X X X 2 X X 2 X X

X 2 X X 1 2 1 1 2 1 2 1 1 X X X 1 X 2 1 1 1 1 X X 2 1 X X

X 1 1 2 2 2 2 X X 2 X 1 X X 2 2 2

X X X 2 2 2 X X X X 2 X 2 X X

X 1 1 1 1 1 X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

X 1 1 1 X 2 X X X 2 X 1 2

1 1 1 1 1

1 X 1 1 2 1 1 1 1 1 1

X X 1 1 1 1 1 X 2 2 1 1 2 X 2

X X X X X X 1 1 1 1 2 2 1 1 1 2 2 X 1 2 1 1 1 1

X X 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 1 1 1 1 1 1 1

1 1 X X X X 1 1 1 X 1 1 1 1 1 1

1 1 2 2 2 2 1 X X 1 1 1 X 1 2 1 1 1 1

Liquid

™

Form (at room temperature Chemical unless otherwise stated) Kerosene Water White Oily Liquid Ketchup Red Liquid Ketoglutaric Acid In Water or Alcohol Ketones (ie Acetone, MEK, Cyclohexanone ) Generally Liquids Koch Acid White Solid

Teflon /Neoflon

CPE

Hypalon

Fluorocarbon

Butyl

Neoprene

SBR

NBR

Sanitron

EPDM

UHMWPE

Gatron

NOTE: Ratings are for the effect on the polymer only !

L Lacquer - Alcohol or Acetate as Solvent Lacquer - Toluene or Xylene as Solvent Lactic Acid (90% or less) Lactic Acid, Food Grade - 50-80% Lactic Acid, Plastic Grade - 50-80% or less Lactic Acid, USP 85-90% or less Lactol Lard (Fat of the Hog) Lard Oil Lasso (Alachlor) Latex Paint Lauryl Peroxide Lauryl Alcohol Lead Acetate Lead Acetate Solution Lead Arsenate Lead Arsenate Solution (In Nitric Acid) Lead Nitrate Solution (In Water or Alcohol) Lead Silicate (basic) Lead Sulphate (Basic, Blue Basic, Tribasic) Lead, Tetraethyl (Tetraethyl Lead) Lead, Tetramethyl (Tetramethyl Lead) Lecithin Ligroin Lime (Calcium Oxide) Lime Sulfur Solution Lime, Chlorinated (Bleaching Solution) Lime, Chlorinated (normal 35-37% Chlorine) Lime, Hydraulic (Calcined Limestone) Lime, Slaked (Calcium Hydroxide) Limestone Limonene Lindane (Ag Spray) Linoleic Acid Linseed Oil Liquid Soap Lithium Chloride Lithium Chloride (35-40% Brine) Lubricating Oil Diester (Under 135°F/57°C) Lubricating Oil (SAE 10, 20, 30, 40, & 50) Lubricating Oil (Under 120°F/49°C)

Solution Solution Colorless-Yellow Liquid Colorless to Yellow Liquid Colorless to Yellow Liquid

M Machine Oil (Under 135°F/57°C)

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 195

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Neoprene

Butyl

Fluorocarbon

1 X 1 1 1 -

1 1 1 1 -

1 2 1 1 -

1 1 1 1 1 1 1 1 1

1 1 1 2 1 1 1 1

1 1 1 1

2 1 1 -

2 2 2 2 2 2 -

1 1 1 1 1 1

1 1 1

X 1

2 X X 1

PVC

1 1 1 1 1 1 -

Nylon

1 1 1 1 1 1 1 1 -

- 1 - 1 - 1 1 1 1 1 - 1 - 1 1 - 1 - 1 - 1 - 1 1 - 1 2 - 2 1 1 1 1 2 1 - X X 1 1 NO HOSE AVAILABLE 2 2 2 X - 1 - 1 1 X X - 1 1 2 2 - 1 - 1 USE LPG HOSE ONLY 1 - 2 X X X X 2 2 2 2 2 1 X X X X 2 - 1 2 2 1 1 2 - 1 2 2 2 1 2 2 2 2 1 2 NO HOSE AVAILABLE X X X X 2 X X X X X 1 X X X 1 - 2 2 1 1 1 1 1 1

CPE

1 1 1 1 1 1 2 2

EPDM

1 1 1 1 1 1 -

Hypalon

Sanitron

1 1 1 1 1 1 1 1 1 -

™

UHMWPE

1 1 1 1 1 1 1 1 1 1

™

1 1 1 1 1 1 1 1 1 1 1

Gatron

Teflon /Neoflon

Form (at room temperature Chemical unless otherwise stated) Magnesite White to Brown Crystalline Solid Magnesium Powder Magnesium Acetate Colorless Crystalline Aggregate Magnesium Acetate Solution In Water or Alcohol Magnesium Carbonate White Powder Magnesium Carbonate Solution (in Acid) Liquid Solution Magnesium Chloride Colorless to White Crystals Magnesium Chloride Brine Solution Magnesium Chloride, Hydrated (in H2O or Alcohol) Solution Magnesium Hydroxide White Powder Magnesium Hydroxide Solution (in Dilute Acid) Liquid Solution Magnesium Nitrate White Crystals Magnesium Nitrate Solution (in H2O or Alcohol) Liquid Solution Magnesium Oxide, Dry White Powder Magnesium Oxide, Slurry Magnesium Sulfate Solution Liquid Solution Malathion (Ag Spray Dilute) Clear to Amber Liquid Malathion (Ag Spray) Clear to Amber Liquid Maleic Acid Liquid Maleic Acid Solution Solution Maleic Anhydride Colorless Needles Maleic Anhydride (Heated Liquid) Liquid above 124°F (53°C) Malic Acid (dl form) Colorless Crystals Malic Acid Solution (in H2O or Alcohol) Solution Malt Extract (Maltine) Light Brown Viscous Liquid Malt, Dry Yellow to Amber Grain Maltine (Malt Extract) Light Brown Viscous Liquid Manganese Salts Manganese Sulfate (Manganous Sulfate) Pale Red Solid Manganese Sulfate Solution Solution in Water Manganese Sulfide (Manganous Sulfide) Green Crystals Manganese Sulfite (Manganous Sulfite) Black to Brownish Red Powder MAPP Gas (Methylacetylene Propadiene) Liquid Maxmul (Penzoil Hydraulic Fluid) Liquid Mayonnaise Semi-Liquid MBK (Methyl Butyl Ketone) Colorless Liquid MEA (Ethanolamine) Colorless Viscous Liquid MEK (Methyl Ethyl Ketone) Colorless Liquid Mercuric Chloride White Powder Mercuric Chloride Solution (in H2O, or Alcohol) Solution Mercuric Cyanide Colorless Transparent Prisms Mercuric Cyanide Solution (in H2O or Alcohol) Solution Mercurous Nitrate Solution Solution Mercury Silver Liquid Mercury Vapor Gas Mesityl Oxide (Methyl Isobutenyl Ketone) Colorless Oily Liquid Mesitylene (Trimethylbenzene) Liquid Metallic Soaps (Aluminium, Calcium, Zinc) Solids @ Room Temperature Methallyl Alcohol (Methylallyl Alcohol) Colorless Liquid Methane Gas Methanol (Methyl Alcohol) Colorless Liquid

1 1 1 1 1 1 1 1 1 -

1 1 -

1 1 1

1 1 1 -

7 1 1 1 1 1 -

1 1 -

1 -

X 1 1 -

X X X 1 -

X X X 1 1 1

2 1 2 1 1

1 -

1 X 2 X 2 1

X 1 1 2 1 X

X 2 2 1

2 1 1

1 1

X X 2

Polypropylene

Brass

Aluminum

Stainless Steel 316

SBR

Food & Bev. Mstr.

NOTE: Ratings are for the effect on the polymer only !

NBR

Renegade

T K

™

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Stainless Steel 304

Couplings / Adapters

G ates Hose / Polymers

Iron/Carbon Steel

Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

1 1 X 1 1 1 1 2 1 1 2 2 1 1 1 X X 1 1 1 1 1 1

1 1 2 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

X X X X X 1 1 X X X X X X 1 1 1

2 1 1 1 1 1 1 1 X X X 1 1 2

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 196

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Butyl

Fluorocarbon

1 X X X X X 1 X X X X X X X X 2 X X X 1 X X X X X X X X X X X X X 2 -

X X X 1 X X X X X X X 2 X X X X X X X 2 X -

2 2 2 X 1 1 X X 1 2 X X X X X X X 2 2 1 2 2 2 2 2 2 X X 2 1 X 2 2 2 1 2 -

X X X X 1 X 1 1 1 X 1 1 1 1 1 X 1 X X 2 X X X X X X X X 1 1 X X 1 1 2 1 1

Polypropylene

Neoprene

X X X 1 X X X X X X X X 2 X X X X X X X X X X X -

Brass

X X X X 2 1 X 1 X X X X X 1 X X 1 X X X X X X X X X X X 2 X 2 1 X -

Aluminum

SBR

2 2 1 2 2 1 X X 1 2 1 1 X X X 2 X 2 2 2 2 2 X 1 2 2 X 2 2 -

Stainless Steel 316

NBR

2 1 1 X 1 1 1 X X 1 X 1 2 1 1 -

Stainless Steel 304

Iron/Carbon Steel

PVC

Nylon

CPE

Hypalon

Sanitron

Food & Bev. Mstr. P

EPDM

™

Renegade

X X X X 1 X X X X X X X X X X X 1 X X X X X X 2 X X 2 X X 2 -

1 1 1 1 2 1 1 X X 1 2 2 2 2 2 2 1 1 1 1 1 -

1 1 1 X 1 1 1 X 1 1 1 1 X X 1 X -

X X 1 2 X X 1 X X X 1 X X X X 1 X X 1 1 X X -

1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 -

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -

1 1 1 1 1 1 1 1 1 1 -

1 1 2 1 1 1 1 1 1 1 1 -

2 -

1 1 1 1 2 1 1 1 1 -

™

1 2 2 1 1 1 1 1 1 1 1 1 2 2 1 2 1 1 2 2 2 2 1 1 1 1 2 1 1 1 1 1

™

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Liquid @ 160 PSIG @ 120°F (49°C) 1 Colorless Liquid 1 Colorless Liquid 1 Colorless Liquid 1 Colorless Liquid 1 Colorless Liquid 1 Colorless Liquid 1 1 Colorless Liquid 1 Colorless Liquid 1 Colorless Liquid 1 Colorless Oily Liquid 1 Colorless Liquid 1 Colorless Liquid 1 Colorless Liquid 1 Colorless Liquid 1 Liquid above 95°F (35°C) 1 Colorless Liquid 1 Colorless Liquid 1 Water White Liquid 1 Yellow to Red Liquid 1 Liquid above 99°F (38°C) 1 Colorless Liquid 1 Colorless Liquid Colorless Liquid 1 Water White Liquid 1 Liquid @ 107 PSIG @ 68 F° (20°C) 1 White Crystalline Solid 1 Colorless Liquid 1 Colorless Liquid 1 Colorless to Straw Colored Liquid 1 Colorless Liquid 1 Liquid @ 120 PSIG @ (120°F (49°C) 1 Colorless Liquid 1 Colorless Liquid 1

UHMWPE

(at room temperature unless otherwise stated) White Crystalline Powder Solution Liquid Colorless Liquid Colorless Liquid Water White Liquid Colorless Liquid White Solid Colorless Liquid Liquid @ 55 PSIG @ 120°F (49°C) Colorless to Straw Colored Liquid Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid

Gatron

Methyl Chloride Methyl Chloroform (1,1,1 Trichloroethane) Methyl Chloroformate Methyl Cyanide (Acetonitrile) Methyl Cyclohexane Methyl Ethyl Ketone (MEK) Methyl Formate Methyl Hexanol Methyl Hexanone (Methyl Isoamyl Ketone) Methyl Hexyl Ketone Methyl Isoamyl Ketone (Methyl Hexanone) Methyl Isobutenyl Ketone (Mesityl Oxide) Methyl Isobutyl Ketone (MIBK) Methyl Isopropyl Ketone Methyl Methacrylate Methyl Methacrylate Monomer, Inhibited Methyl Phenol (Cresol) Methyl Propyl Carbinol (2 Pentanol) Methyl Propyl Ether Methyl Propyl Ketone (Pentanone) Methyl Salicylate Methyl Stearate Methyl Sulfate (Dimethyl Sulfate) Methyl-2-Pyrrolidone Methyl-n-Amyl Carbinol Methyl-n-Amylketone Methylacetylene Propadiene (MAPP Gas) Methylacrylic Acid (Crotonic Acid) Methylal Methylallyl Alcohol (Methallyl Alcohol) Methylallyl Chloride Methylamine (30-40% in H2O) Methylamine (Anhydrous) Methylamyl Acetate Methylamyl Alcohol

Teflon /Neoflon

Form

Methyl Cellosolve (Diethylene Glycol Methyl Ether)

T K ®

NOTE: Ratings are for the effect on the polymer only !

Chemical

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Methionine Methoxychlor Solution (in Alcohol) Methyamine (Monomethylamine) Methyl Acetate Methyl Acetoacetate Methyl Acetone Methyl Acrylate (Inhibited) Methyl Acrylate Acid(Methylacrylic Acid) Methyl Alcohol (100%) (Methanol) Methyl Bromide Methyl Bromoacetate Methyl Butanathiol (Butyl Mercaptan) Methyl Butanol (2-Methyl-1-Butanol) Methyl Butyl Ketone (MBK) Methyl Carbitol (Diethylene Glycol Methyl Ether)

Couplings / Adapters

G ates Hose / Polymers

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 197

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

SBR

Neoprene

Butyl

Fluorocarbon

G Polypropylene

Brass

Aluminum

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

NBR

Food & Bev. Mstr.

™

Renegade

EPDM 2 X X X -

1 2 X 2 X 1 2 X -

1 1 1 1 1 1 2 X 1 1 1 1 1 1 X X

1 1 1 1 1 1 1 X 1 1 1 1 1 1 1 1 X 1

1 X X 2 2 1 2 X 1 1 X -

1 1 1 1 1 1 X 2 1 1 1 X 1 1 X -

1 -

White Powder Liquid Solution White Powder Colorless Liquid Powder Liquid Liquid Liquid Colorless Liquid Colorless to Yellow Liquid Liquid

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 1 1 1 1 2 2 2 1 1 1 1 1 1 2 1 -

1 X X 1 1 1 1 -

X X 1 1 X 1 1 1 1 X 1 2 1 2

Colorless Liquid Colorless Liquid Colorless Liquid Liquid White Crystalline Flakes Commercial Grade is Dark Fluid Colorless Liquid Liquid Green Crystals Solution Green to Brown Crystals/Powder Brown Deliquescent Scales Solution Green Deliquescent Crystals Solution

1 1 1 1 1 1 1 1 1

1 2 2 1 1 1 1 1 1

1 1 1 -

X X 2 1 -

X X 1 1 2

2 1 1 1 1 X X -

1 1 1 1 1 2 2 -

1 1 1 1 1 2 2 2 2

1 1 1 X X X X

1 1 1 1 1 X X -

Hypalon

CPE

Nylon

PVC

Liquid @ 120 PSIG @ 120°F (49°C)

Sanitron 1 1 X X X -

™

1 2 2 -

™

1 1 1 1 1 1 2

(at room temperature unless otherwise stated) Colorless to Brown Liquid Colorless Liquid Clear Liquid Colorless Liquid Colorless Liquid Colorless Liquid Liquid above 99°F (37°C) Colorless Liquid Colorless Liquid White Liquid Colorless Liquid Colorless Liquid Liquid Liquid Brown Liquid Colorless to Light Brown Crystals Liquid Solution Clear Liquid Colorless Liquid Liquid @ 15 PSIG @ 120°F (49°C) Liquid Solution Liquid to Solid

UHMWPE

Teflon /Neoflon

Gatron

Monochlorobenzene Monoethanolamine Monoethylamine Monoethylamine Solution (70% or less) Monoglycerides Monomethylamine (Methyamine) Monopentaerythritol (Pentaerythritol) Monopentaerythritol Solution Monosodium Phosphate (Monobasic) Morpholine Mortar, Inorganic Motor Oil Mould Oil Mouth Wash MTBE (Methyl Tertiary Butyl Ether) Muriatic Acid (Hydrochloric) Mustard

1 1 1 1 1 1 1 1

Form

Monochloroacetic Acid Solution (in H2O or Alcohol)

T K ®

NOTE: Ratings are for the effect on the polymer only !

Chemical

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Methylaniline Methyldiethanolamine Methylene Bromide Methylene Chloride (Dichloromethane) Methylene Dichloride Methylene Dichloride (Methylene Chloride) Methylene Diphenyl Diisocyanate, MDI Methylstyrene MIBK (Methyl Isobutyl Ketone) Milk Mineral Oil Mineral Spirits (VM&P Naphtha) MIPA (Isopropanolamine) Mobile Therm 603 Molasses Monochloroacetic Acid

Couplings / Adapters

G ates Hose / Polymers

1 1 2 1 1 1 X

2 X X X X

X X X 2

X X X X 1

X X X X X X

X X 1 2 X 2 1 1 2 X X -

X - X 2 X X X X X X X X X X X X X X X X X X X 2 USE FDA HOSE ONLY 1 X X 1 X 1 X X X 2 - 2 1 1 2 2 2 2 1 - X X X X X X 2 2 2 2 2 X X X X 2 - 1 - 2 2 X 2 - 1 1 X X 2 X X 2 2 X 2 - 1 1 1 1

1 1 X 1 1 1 X X 1 1 X 1 -

1 X X 1 X X X 2 2 1

1 X 1 1 1 1 1 -

1 1 X X 1 1 1 X -

2 X X X X 2 2 2

X 1 2 2 1 2 2 2

1 1 1 1 1 1 1

X X 2 2

1 1 1 1

1 1 1 -

N n-Hexaldehyde n-Methyl-2-Pyrrolidone n-Octane Naphtha (Low Aromatic Content) Naphthalene Naphthenic Acid Neohexane Neutral Oil Nickel Acetate Nickel Acetate Solution (In Water or Alcohol) Nickel Carbonate Nickel Chloride Nickel Chloride Solution (In Water or Alcohol) Nickel Nitrate Nickel Nitrate Solution (In Water or Alcohol)

X X X X 2 2 2

X X X 1 X 1 2 1 1 2 1 2

2 X 2 2 2 2

1 X X X 1 2 2

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 198

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Neoprene

Butyl

Fluorocarbon

G Polypropylene

Brass

Aluminum

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

SBR

NBR

Food & Bev. Mstr.

™

Renegade

T K

1 X X 1 X -

1 X X X X X X X X X X 1 1 1 1 X 1 -

1 2 2 X 1 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 -

1 1 1 2 1 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 -

X X X 1 1 1 X X -

X X X X X X X X X X X X 1 1 1 1 X 1 1 X -

1 2 2 2 1 2 X -

X 1 1 1 -

2 1 1 1 -

1 1 1 1 -

X 1 1 1 -

X 2 2 1 -

2 1

Sanitron

EPDM

1 2 1 2 2 2 2 X X X X 1 -

1 2 1 2 2 1 2 2 X X X X X X 2 2

1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 -

1 1 1 -

1 1 1 1 -

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 1 1 1 2 2 2 1

1 1 2 -

1 1 X 2 X X

Hypalon

CPE

Nylon

PVC

UHMWPE 1 1 1 1 1 X X X X X X -

™

Gatron 1 1 1 1 1 1 1 1 1 1 2 2 X X X X 2 1

™

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Form (at room temperature unless otherwise stated) Liquid Yellow Green to Blue Crystals Solution Colorless Oil Colorless Crystals to White Lumps Solution Colorless Liquid Transparent or Yellowish Liquid Transparent or Yellowish Liquid Colorless Liquid Colorless to Yellow Liquid Colorless to Yellow Liquid Transparent or Yellowish Liquid Colorless to Yellow Liquid Yellow Liquid Red Liquid Yellow Liquid @ 43°F (6°C) Colorless Liquid Liquid Colorless Gas Liquid @ 50 PSIG @ 120°F (49°C) Solutions in Water Gas Liquid @ 50 PSIG @ 120°F (49°C) Colorless Liquid Colorless Liquid Yellow-Red Liquid or Gas Light Blue Liquid Gas Liquid @ 800 PSIG @ 68°F (20°C) Colorless Liquid Colorless Liquid Colorless Liquid

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

Chemical

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Nickel Plating Solution Nickel Salts Nickel Sulfate Nickel Sulfate Solution Nicotine Salts (ie Nicotine Hydrochloride) Niter Cake (Sodium Bisulfate) Niter Cake Solution Nitric Acid (25% or less) Nitric Acid (10%) Nitric Acid (25%) Nitric Acid (35% or less, 26 Degrees Baume) Nitric Acid (52% or less, 36 Degrees Baume) Nitric Acid (61% or less, 40 Degrees Baume) Nitric Acid (63.5% or less) Nitric Acid (67% or less, 42 Degrees Baume) Nitric Acid (95% or less, 48.5 Degrees Baume) Nitric Acid (Red Fuming) Nitrobenzene Nitroethane Nitrogen (Cryogenic Liquid) Nitrogen (Gas) Nitrogen Dioxide (Nitrogen Tetroxide) Nitrogen Fertilizer (Ammonia, Urea) Nitrogen Oxide (Nitrous Oxide) Nitrogen Tetroxide (Nitrogen Dioxide) Nitromethane Nitropropane Nitrosyl Chloride Nitrous Acid (Up to 10%) Nitrous Oxide (Nitrogen Oxide) Nitrous Oxide, Compressed Liquid Nonene (1-nonylene) Nonyl Alcohol (Octyl Carbinol) Nonylene (Nonene)

Couplings / Adapters

G ates Hose / Polymers

1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 -

2 1 2 1 1 2 2 2 1 2 2 X X X X X 2

1 1 1 1 1 1 X X X X X X X X 1

1 1 X X X X X X X X X X 2 -

X 2 1 1 1 X X X X X X X X X X X -

1 2 2 2 2 -

2 2 2 1 1 1 1 1 - 1 2 2 2 2 2 1 1 1 1 1 - X X 2 X X X X 2 X X X X 2 X X X X 2 X X X X 2 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 2 2 X 2 NO HOSE AVAILABLE 1 1 1 1 1 X X X X 1 X - 2 X 2 X X X X 2 - 1 X X X X 1 1 -

1 1 1 1 X X 1 1 1 1

1 1 X 1 1 -

1 1 1 -

1 X 1 1 1 X -

2 X X X X X

2 2 X 2 X 1 X 1 1 1 2 1

1 1 1 X 1 X 1 X 1 1 1 1 1

2 1 X X 2 X X 2 X

1 1 1 1 1 1 2 -

1 1 1 1 1 1 1

O Octadecanoic Acid (Stearic Acid) Octanoic Acid (Caprylic Acid) Octanol (Octyl Alcohol) Octene Octyl Acetate Octyl Alcohol (Octanol) Octyl Aldehyde Octyl Carbinol (Nonyl Alcohol) Octyl Phenol (Diisobutyl Phenol) Octylamine Oil (SAE Motor Oils) Oil of Turpentine Oils, Animal (High Fatty Acid Content) Oils, Mineral (Aliphatic or Aromatic) Oils, Vegetable (Soybean, Coconut, Corn)

Colorless Waxy Solid Colorless Oily Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid Colorless Liquid White Flakes Water White Liquid Liquid Liquid Solid to Liquids Liquids Liquids

2 2 2 X X X X X

2 2 X 2 X 1 X X X X X X

2 2 2 2 2 2 X -

2 X X 2 X X 2 X X

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 199

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Couplings / Adapters

Neoprene

Butyl

Fluorocarbon

G Polypropylene

Brass

Aluminum

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

SBR

2 2 X 1

2 1 1 2 1

1 1 1 1 1 1

1 1 2 1

2 2 1 X 1

1 X 1 1 1

1 1 2 X X 2 X X X X 1 2 X X -

1 1 2 1 1 1 2 X X -

1 1 2 1 1 1 1 2 1 1 1 1 -

1 1 1 1 1 1 1 1 1 1 1 1 -

1 1 1 1 1 1 2 _ -

1 1 X 1 1 1 X 1 X X -

1 1 1 -

Sanitron

EPDM

2 X 2 X X 2 1

2 X 2 X X X 2 1

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 2 1 1 1 1 1 1 X 1 2 2 2 1 X 1 1 2 2 2 -

1 1 1 1 1 1 X 1 2 1 X 1 1 2 2 -

1 X X 2 X 2 X X 1 2 2 X X X X X X 2 2 -

Hypalon

CPE

Nylon

PVC

UHMWPE 2 X 1 X 2 1 -

™

Gatron 2 X 1 2 X 2 1

™

1 1 1 1 1 1 1 1 1

Form (at room temperature Chemical unless otherwise stated) Oleic Acid (fatty acid) Yellow to Red Oily Liquid Oleum (Fuming Sulfuric, 30% SO3 or less) Clear to Off White Fuming Liquid Olive Oil Yellow to Green Liquid Ortho-Dichlorobenzene (also meta and para) Colorless Liquid Ortho-xylene (1,2 Dimethylbenzene) Clear Colorless Liquid OS 45 Hydraulic Fluid (Silicate Ester Base) Liquid Oxalic Acid Transparent Crystals Oxalic Acid (50%) Crystals in H2O Oxygen Colorless Gas Liquid @ 200 PSIG @ -231°F (-146°C) Oxygen, Refrigerated Liquid Ozone Gas

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

NBR

Food & Bev. Mstr.

T K

™

Renegade

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Stallion ® Mustang

G ates Hose / Polymers

2 1 1 1 1 1 1 1

X X X X X 2 2 1

2 X 2 X X 1 1

X 1 1 X X -

2 X 2 X X X -

2 X X 2 2 X X X X X 2 X X X 2 X X X X X X X X X X 2 X X 1 X - 1 X X X X 2 2 2 2 1 NO HOSE AVAILABLE X X X 2 2

2 X X 2 X X X 1 2 2 X X X X X X 2 2 -

2 2 X 1 2 1 2 1 X X 2 X 2 X 1 1 X X X -

1 1 1 1 1 1 1 1 1 1 X 1 1 1 1 1 1 1 1 1 1 1 1 2 1 -

X X 2 X X X 2 2 X X X 2 X X X X -

1 1 1 1 1 2 1 X 1 1 -

1 1 X 1 X 2 X 1 X X 2 -

P Paint (Emulsion or Latex) Paint (Inorganic) Paint (Oil or Solvent Based) Paint Remover Paint Resin Palm Oil Palmitic Acid (Hexadecanoic Acid)

Liquid Liquid Liquid or Paste Liquid or Paste Yellow to Brown Solid Crystals in Hot Alcohols Papermakers Alum (Aluminum Ammonium Sulfate) In Water Paraffin (Aliphatic Hydrocarbon) Varies from Gas to Waxy Solid Paraformaldehyde White Solid - Flakes or Powder Paraldehyde Colorless Liquid Paranox (Detergent, Disperser; Exxon) Parapol (Liquid Polyisobutylene; Exxon) Liquid Peanut Oil Yellow to Green Liquid Pelargonic Acid Colorless to Yellow Oil Pentachloroethane Colorless Liquid Pentachlorophenol In Oil In Oil (Wood Preservative) Pentaerythritol (Monopentaerythritol) White Powder Pentane Colorless Liquid Pentanol (Methyl Propyl Carbinol) Colorless Liquid Pentanone (Methyl Propyl Ketone) Water White Liquid Pentasol (Amyl alcohols, primary and secondary) Liquid Perchloric Acid (70%) 70% or Less with H2O Perchloroethylene Colorless Liquid Petroleum Coke Solid Pellets Petroleum Distillate Liquid Petroleum Ether (Naptha) Liquid Petroleum Naphtha (Toluene/Cyclohexane/Xylene) Liquid Petroleum Naphtha Flash Point Over 200 Degrees Liquid Petroleum Oils (Refined) Liquid Petroleum Oils (Sour) Liquid Petroleum Paraffin Wax Solid with low Melt Points Phenol (Carbolic Acid) White or Pink Crystals Phenol Acid 95% or less with H2O Phenolates Phenolsulfonic Acid Yellow to Brown Liquid Phenothiazine Greenish Powder or Flakes Phenyl Acetate Water White Liquid

X X X X X X 2 2 X X X X X X X -

X X X X X 1 X 1 X 2 2 X 1 X X X X X X 1 -

X 2 2 2 2 2 X X 2 2 X X X 2 2 X X X -

X X 2 2 X X 1 1 2 2 2 X X X X X 2 2 -

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 200

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

Neoprene

Butyl

Fluorocarbon

X X X X 2 2 X 2 2 2 2 2 2 1 1

X X X X 2 2 X 2 X X X -

X 1 X X X 1 2 2 X 1 2 X X X 1 1 1 1 1 1

X X X X 2 2 X 2 X X 1 1 2

X 2 2 2 2 X 2 X X X 2 1 1 2 1

1 X 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 1 2 1 1 2 -

1 1 1 1 1 1 1 2 -

1 1 -

2 1 1 1 1 1 1 2 1 -

2 1 1 1 1 1 1 X 1 -

2 1 1 1 1 1 1 2 1 -

X 1 1 1 1 1 1 1 1 -

CPE

X 2 X 1 2 1 1 2 2 2 1 2 2 X X X 2 1 1 1 2 1

X 2 2 X X X X 1 1 X 2 2 -

X X X X 1 1 X X X 2 -

1 1 X X X X X X 1 -

1 1 1 1 2 2 1 1 1 X -

1 1 1 1 2 1 1 2 2 -

1 1 1 1 1 1 1 1 1 1 1 1 -

2 2 -

1 1 1 -

Sanitron

EPDM

X X 1 2 1 1 2 2 2 2 2 X X 1 1 1

Hypalon

UHMWPE X 1 1 X 1 1 1 1 1 1 X 2 2 X 1 -

™

Gatron 2 1 X 1 1 2 1 1 2 2 2 1 2 2 1 2 1 1 2 1 1 1 1 1 -

™

Teflon /Neoflon

Form

(at room temperature Chemical unless otherwise stated) Phenyl Chloride (Chlorobenzene) Clear Volatile Liquid 1 Phenylenediamine (ortho) Colorless to Red Solid Needles Phorone (Diisopropylidene Acetone) Yellow Liquid 1 Gas, Liquid 60 PSI @ 120°F (49°C) 1 Phosgene (Carbonyl Chloride) Phosphate Ester Hydraulic Fluid Liquid 1 Phosphate Rock Solid Phosphate, Trisodium In Water 1 Phosphoric Acid (100%) Crystals 1 Phosphoric Acid (35% or less) Colorless Liquid 1 Phosphoric Acid (50%) Colorless Liquid 1 Phosphoric Acid (75%) Colorless Liquid 1 Phosphoric Acid (85%) Syrupy Liquid 1 Phosphoric Acid (90%) Syrupy Liquid 1 Phosphoric Acid, Spent Liquid 1 Photographic, Developers 1 Photographic, Emulsions Liquid 1 Photographic, Fixing Solutions Liquid 1 Phthalic Acid Colorless Crystals Phthalic Acid (50%) Colorless Liquid 1 Phthalic Anhydride, Molten White Crystalline Solid Picric Acid (Solution) In Water 1 Picric Acid (Trinitrophenol) Yellow Crystals 1 Pine Oil Colorless to Amber Liquid 1 Pine Tar Viscous Brown to Black Liquid 1 Pinene Colorless Transparent Liquid 1 Piperazine Hydrochloride Solution (34%) In Water 1 Pitch In Aromatic Hydrocarbons 1 Plating Solution Chrome (Under 120°F/49°C) Liquid 1 Pluronic (Block Polymer with Hydroxyl by BASF) Liquid 1 Polyester Plastic 1 Polyethylene Glycol Colorless Liquid to glassy Solid 1 Polyethylene Plastic Solid Beads Polypropylene Glycol Liquid 1 Polypropylene Plastic Solid Beads Polystyrene Plastic Solid Beads Polyurethane Foam (Under 125°F/52°C) 1 Polyvinyl Acetate - Emulsions Emulsion 1 1 Potash (Potassium Carbonate) Aqueous Solution Liquid Potassium Acetate White Powder 1 Potassium Bicarbonate Colorless crystal or white Powder 1 Potassium Bisulfate Colorless crystal 1 Potassium Bromate White Crystal or Powder 1 Potassium Bromide White Crystals or Powder 1 Potassium Carbonate White granular Powder 1 Potassium Carbonate, Liquid Colorless to Cloudy Liquid 1 Potassium Chlorate Colorless to white Powder 1 Potassium Chloride Colorless to white Solid 1 Potassium Chloride, Dry White Solid 1 Potassium Chromate Yellow Crystal 1 Potassium Cuprocyanide White Crystalline Solid 1 Potassium Cyanide White Crystal 1

X X X X 1 1 1 1 2 X X 1 1 1

X 1 1 1 1 2 2 -

2 1 1 1 1 1 1 2 1 -

1 1 1 1 1 1

Polypropylene

Brass

Stainless Steel 304

Iron/Carbon Steel

PVC

Nylon

SBR

Food & Bev. Mstr.

NOTE: Ratings are for the effect on the polymer only !

NBR

Renegade

T K

™

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Aluminum

Couplings / Adapters

G ates Hose / Polymers

Stainless Steel 316

Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

1 1 1 1 2 2 1 1 1 X -

1 X X X X X X -

1 1 2 2 X X X X -

X 1 1 1 1 1 1 1 -

1 1 1 -

X X -

1 1 1 1 1 1 -

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 201

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products

SBR

Neoprene

Butyl

Fluorocarbon

PVC

- 1 - 2 2 2 2 2 1 X 1 1 2 2 2 2 1 2 - 1 - 1 2 2 2 2 1 X 2 - 1 1 - 1 1 1 - 1 - 1 - 1 1 1 - 1 1 2 - 1 1 1 - 1 - 1 1 - 1 1 1 2 - 1 - 1 - 1 1 1 CONTACT DENVER PRODUCT APPLICATION - 1 1 - X 1 1 2 1 1 1 1 - 1 1 2 X 2 2 X 2 1 2 1 X - 2 1 1 1 1 - 1 - X - X 2 X X - X - X X 2 X - X X X X X X 1 X - 2 - 2 2 X - X X X X X X 2 X 1 1 1 1 1 1 1 1 1 1 1 - 2 X - X 2 2 - X 1 X - 2 X 2 - 2 - X 2 1 - 2 - 2 X X X X 2 1 X 2 - 2 X X X X 2 2 X 2 2 X X X X X X 1 - 2 - 2 2 2 - 2 - X X X X X X 1 X 2 - 2 X X X X 2 1 X 2 - X X X X X X 1 X 2 - 2 X X X X 2 1 X 2 X X X X X X X 1 X 2 2 - X X X 2 - 2 X 2 - X 1 X 1 -

Nylon

1 1 1 1 X -

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1

Hypalon

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Sanitron

1 -

™

UHMWPE

1 1 1 1 1 -

™

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Gatron

Teflon /Neoflon

Form (at room temperature unless otherwise stated) White Crystalline Powder Yellow Crystal or Powder White Crystalline Powder White Solid Colorless to Cloudy Liquid Colorless to Cloudy Liquid White Solid Colorless to white Solid Dark purple Crystal White Crystal Colorless to white Crystal White Crystal or Powder Red or yellow Crystal or Solid White Crystal or Powder Colorless crystal Liquid Colorless Gas Colorless Liquid Colorless Liquid Colorless Oily Liquid Colorless Liquid Colorless Liquid White-water Liquid Colorless Liquid Colorless Gas Colorless Liquid Colorless Liquid Liquid Colorless Liquid Liquid Liquid Liquid Liquid Liquid Liquid Liquid Liquid Liquid Liquid Liquid Colorless Liquid Liquid Liquid Liquid Liquid Liquid

2 2 1 X 1 X 1 -

1 1 1 2 1 X 1 1 X 1 1 2 1 -

1 1 2 2 1 2 2 2 1 1 X 2 2 2 1 1 -

2 2 1 2 X X X X X X X X X 2 X 2 -

Polypropylene

Brass

Aluminum

Stainless Steel 316

Stainless Steel 304

CPE

NBR

EPDM

Food & Bev. Mstr.

™

Renegade

T K ®

NOTE: Ratings are for the effect on the polymer only !

Chemical

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Potassium Dichromate Potassium Ferrocyanide Potassium Fluoride Potassium Hydrate Potassium Hydroxide (45% Caustic Potash) Potassium Hydroxide, Liquid Potassium Iodide Potassium Nitrate Potassium Permanganate Potassium Persulfate Potassium Phosphate Potassium Silicate, Other Than Dry Potassium Sulfate Potassium Sulfide Potassium Sulfite Potassium Thiosulfate Primatol A, S, P (Ag Spray) Propane Gas Propanediol Propanol (Propyl Alcohol) Propionic Acid Propyl Acetate Propyl Alcohol (Propanol) Propyl Aldehyde Propyl Chloride Propylene Propylene Diamine Propylene Dichloride (Dichloropropane) Propylene Glycol Propylene Oxide Purina Insecticide Puropale RX Oils Pydraul 10E, 29E-LT, 30E, 60, 65E, 115SE Pydraul 135 Pydraul 150 Pydraul 280 Pydraul 312 Pydraul 50E Pydraul 540 Pydraul 625 Pydraul A-200 Pydraul F-9 Pyrene (Carbon Tetrachloride) Pyrethrum Pyridine (50%) Pyrogard 160, 230, 630 Pyrogard 51, 53, 55 Pyrogard C, D Pyronal (Transformer Oil)

Couplings / Adapters

G ates Hose / Polymers

Iron/Carbon Steel

Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

1 1 1 1 1 1 1 1 1 1 1 1 X 1 1 1 -

1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 -

1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 -

1 1 1 1 X 1 1 -

2 1 1 1 2 1 1 -

1 1 2 X -

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 202

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070 Renegade

Food & Bev. Mstr.

T K

™

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

CPE

Nylon

PVC

Iron/Carbon Steel

Stainless Steel 304

Stainless Steel 316

Aluminum

Brass

Polypropylene

Liquid Liquid

1 1

2 1

2 2

1 1

Liquid Brownish to yellow Liquid Liquid Liquid Liquid

1 1 1 1 1 1 1 1

1 1 1 2 1 1 1 1

2 X 2 -

2 2 -

X 2 2 X X X

1 1 1 1 2 1

X X X -

2 2 X -

X 2 2 X X X

2 1 2 -

X X X -

2 -

1 1 2 1 1 1 1

2 2 2 2

1 1 1 2 1 1 -

1 1 1 1 1 1 -

1 1 1 1 1 -

1 1 1 2 1 1 -

1 -

White Powder Liquid Colorless Liquid Sludge Liquid Orange to colorless flake Brownish or yellow Liquid Liquid Liquid White Powder Colorless crystal Liquid Liquid Liquid Liquid Grayish Powder Liquid Colorless crystal Colorless to cloudy Liquid White Crystals or Powder White Crystal or Powder Red to clear Liquid Colorless Crystals to White Lumps White Crystals or Powder White Crystals Grayish Powder Colorless Crystals Colorless to white Crystals

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 1 2 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 1 X 2 1 1

1 1 1 1 1 1 1

2 1 1 2 1 X 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1

X 2 2 2 1 1 2 2 1 X X 1 1 1 X 1 1 2 1 1 1 1 1 1

2 2 2 2 1 X X 2 1 2 2 1 2 1 1 1 1 1 1

2 X X X 1 1 X X 2 1 2 2 1 2 1 1 1 1 1 1

2 2 2 1 2 2 1 1 X X 2 1 1 X 1 1 2 1 1 1 1 2 1

2 1 1 1 1 2 1 2 1 2 1 1 1 1 1 1 1 2 1

2 1 1 1 2 2 1 X 1 1 1 X 1 1 1 1 1 1 1 1 1

2 2 2 1 2 2 1 X X 1 1 1 X 1 1 2 1 1 1 1 1 1

1 1 2 1 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 1 2 1 1 1 1 1 1

1 1 2 1 2 2 2 1 2 X 1 2 1 1 1 2 1 1 2 1 1 1 1 1 1

2 2 X 1 1 2 1 1 1 1 1 1 2 X 1 2 1 2

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

2 2 1 1 1 X 1 X X X

2 2 1 1 1 2 1 2 1 2 X 2 2 X

1 1 1 1 1 1 -

™

Form

(at room temperature unless otherwise stated)

Hypalon

Fluorocarbon

Butyl

Neoprene

SBR

NBR

Sanitron

EPDM

UHMWPE

Gatron

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

Chemical

Couplings / Adapters

G ates Hose / Polymers

Q Quenching Oil Quintolubric 822

R Ramrod (Ag Spray) Rando Oils Rape Seed Oil Red Oil (Commercial Oleic Acid) (MIL-5606) Refined Wax (Petroleum) Regal Oils R&O Richfield "A" Weed Killer Road Paving Compound Road Tar Rubilene Oils

S Salicylic Acid Salt Water (Sea Water) Sauerkraut Sea Water Sevin Sewage Shampoo Shellac Shortening Silicate of Soda Silicone Greases Silicone Oils Silver Cyanide Silver Nitrate Skydrol 500A & 7000 Soap Oil Soap Solutions Soap, Liquid Soda Ash (Sodium Carbonate) Soda Water Sodium Acetate Sodium Aluminate Solution Sodium Benzoate Sodium Bicarbonate Sodium Bichromate Solution Sodium Bisulfate (Niter Cake) Sodium Bisulfite Sodium Borate (Borax) Sodium Carbonate (Soda Ash) Sodium Chlorate Sodium Chloride

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 203

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Couplings / Adapters

Butyl

Fluorocarbon

2 2 1 1 2 2 2 2 1 1 X 2 1 X X 2 X X 2 1 2 1 X 2 2 2 1 X X 2 1 1 -

2 2 1 1 2 2 2 X 1 1 X 2 1 X X 2 X X 2 1 2 1 2 2 2 2 2 1 X X 2 2 1 1 -

X 1 1 1 2 2 X 1 2 2 2 1 X 2 X X 1 X 1 1 2 1 2 2 2 2 1 1 2 X X 1 2 1 -

2 2 1 1 1 2 2 2 2 1 2 2 2 2 2 2 1 2 1 1 2 1 1 2 1 1 2 1 2 X 2 X X 2 1 X -

X 1 1 1 1 2 1 1 1 X X X X 1 X 1 2 1 1 1 2 1 2 2 2 1 X 1 1 1 1 1 1 -

Polypropylene

Neoprene

X 1 1 1 1 2 X 2 X X X 2 X X 2 2 X X 1 1 2 1 2 2 2 2 1 1 1 2 X 2 2 1 2 1 -

Brass

X 1 1 1 2 1 2 2 2 2 2 2 2 1 1 1 2 2 2 2 1 1 1 1 1 1 2 1 1 1 X X X 2 1 1 -

Aluminum

SBR

1 1 1 1 1 1 1 2 X 1 -

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

PVC

Nylon

CPE

Hypalon

NBR

EPDM

Food & Bev. Mstr.

2 X 1 1 2 2 1 1 1 2 2 1 1 1 2 2 X 1 1 1 2 1 2 2 2 2 2 1 2 2 X 2 1 1 -

1 1 1 1 1 1 1 1 X 1 1 1 1 2 1 1 1 1 1 1 X 1 1 -

X 2 1 1 2 2 X X X X 2 1 1 1 2 X 1 1 1 2 1 X 1 X 2 1 1 1 X X X 1 1 -

2 2 1 1 1 1 1 1 2 2 1 2 1 1 1 1 1 1 1 1 1 2 1 1 2 1 1 X 2 X 2 1 1 1 -

2 2 2 2 X X X X X X 1 X X 1 1 X 1 1 X 1 1

1 1 1 2 2 2 X X X 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1

1 1 2 1 2 2 2 2 2 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1

X X X X X X X X X 1 2 1 1 X 2 X 1 1 1

X X X X X X X X X X 2 X X X X X 1 X 1 1

1 1 1 1 1 1 1 1 1 -

1 1 1 2 2 2 1 1 1 1 2 1 2 -

UHMWPE

1 1 1 2 2 1 1 1 1 1 2 1 2 2 1 1 1 1 1 1 1 2 1 2 1 2 2 1 1 2 1 1 2 1 2 1 1 1 1 1

™

Gatron

2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

™

Form (at room temperature Chemical unless otherwise stated) Sodium Chlorite Solution Colorless to cloudy Liquid Sodium Chromate Yellow, translucent Crystals Sodium Cyanide In Water Sodium Cyanide White Crystaline Powder Sodium Dichromate Red to red-orange Crystals Sodium Ferricyanide Ruby-red Crystals Sodium Ferrocyanide Yellow, transparent Crystals Sodium Fluoride (70%) White Liquid Sodium Hydrate White Solid Sodium Hydrochlorite Pale greenish Liquid Sodium Hydrosulfide Colorless needles Sodium Hydrosulfite Lemon colored Powder or flake Sodium Hydroxide (10%) Colorless Liquid Sodium Hydroxide (40%) Colorless Liquid Sodium Hydroxide (50%) (Under 212°F/100°C) Colorless Liquid Sodium Hydroxide (50%) (Under 115°F/46°C) Colorless Liquid Sodium Hydroxide (50%) (Under 180°F/82°C) Colorless Liquid Sodium Hydroxide (60%) White Liquid Sodium Hydroxide (25%) Colorless Liquid Sodium Hypochlorite (20%) White Liquid Sodium Hypochlorite (5%) White Liquid Sodium Hyposulfate Large, transparent Crystals Sodium Metallic Silver Solid Sodium Metaphosphate Colorless Crystals to white Powder Sodium Nitrate Colorless crystal Sodium Perborate White, amorphous Powder Sodium Peroxide Yellowish white Powder Sodium Phosphate Colorless Crystals to white Powder Sodium Silicate Lumps of greenish glass Sodium Sulfate White Crystals or Powder Sodium Sulfate Decahydrate (Glauber's Salt) Crystals or Powder Sodium Sulfhydrate Colorless to cloudy Liquid Sodium Sulfide Yellow/Brick red flakes or Crystals Sodium Sulfide Solution Colorless to cloudy Liquid Sodium Sulfite White Crystals or Powder Sodium Sulfite Solution Colorless to cloudy Liquid Sodium Sulphydrate Colorless needles Sodium Thiocyanate Solution Colorless to cloudy Liquid Sodium Thiosulfate (HPO) White Powder Sodium Tripolyphosphate (STPP) White Powder Solnus Oils Liquid Sour Crude Oil Liquid Soybean Oil Pale yellow oil Spent Acid Liquid Stannic Chloride Colorless, fuming Liquid Stannic Sulfide Yellow to brown Powder Stannous Chloride (Under 150°F) White Mass Starch White amorphous Powder Starch gum (Dextrin) Yellow or White Powder Stauffer Jet 1 Liquid Stauffer Jet 2 Liquid

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

Sanitron

T K

™

Renegade

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Stallion ® Mustang

G ates Hose / Polymers

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 204

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Polypropylene

Brass

Fluorocarbon

Aluminum

Butyl

Stainless Steel 316

Neoprene

Stainless Steel 304

Iron/Carbon Steel

PVC

Nylon

CPE

Hypalon

SBR

NBR

Food & Bev. Mstr.

™

Renegade

T K

2 1 2 2 2 2 2 2 2 2 2 X 1 X 1 1 1 2 X X X X X 1 1 -

1 1 2 1 1 X 1 X 1 1 1 2 X X X X X 1 1 -

1 2 1 1 2 X 1 2 X 1 X X X X X X X X X X X 1 1 1 1 1 -

1 2 2 X 1 2 1 X X 2 1 X 1 2 2 2 2 2 -

X 2 2 1 X 2 2 2 X X X X X X X X X 1 1 1 1 1 -

2 1 2 X 1 X 1 2 X X X X X X X X X X X X 1 1 1 1 1

1 1 1 2 1 2 1 2 X 2 2 2 2 2 2 2 2 2 1 2 2 1 1 1 1 1 1

X X X 1 2 2 X X X X X X X X X 1 X 1 1 1 -

X 1 X 2 X 1 X X X X X X X X X X X X 1 -

1 X X X -

X X 2 2 1 2

1 1 X 1 1

1 1 1 1 -

X 2 1 1 2 2

2 2 2 1 -

X X 2 1 1 1 2 1

2 2 2 1 1 1 2 1

1 2 2 1 2 -

2 X X 2 1

Sanitron

EPDM

1 2 X 1 1 1 1 1 1 X 1 1 1 1 2 2 2 2 X 1 1 X 1

2 X 2 X 1 1 2 X 2 2 1 1 1 2 1 X 1 1 1 2 X X X X X 1 1 X X X X X -

1 1 1 1 1 1 1 1 1

2 1 1 1 1 1 1 1

1 2 1 -

X 2 2 1 X X 1 -

X X 2 1 X 1 1

USE STEAM HOSE ONLY 2 2 2 2 2 1 2 X X X 1 - 2 2 2 X X X X X 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 X X X 2 1 - X X 2 X X X X X 1 X X 2 X X X X X X 1 X X X 2 2 X X X X 2 1 2 2 2 2 1 1 2 X X X X X 1 2 1 1 1 1 1 X X X X X 2 2 2 2 1 1 1 X X X 2 1 1 X X X X 1 1 X X X X 2 1 X X X X X 1 X X X X X 1 X X X X X 1 X X X X X 1 X X X X X 1 X X X 2 1 X X X X X 1 1 X 1 1 X 1 1 X 1 1 X 1 X - 1 1 2 1

UHMWPE 1 1 1 1 1 X 1 1 1 1 1 1 1 1 X 1 1 -

™

Gatron 1 2 2 2 1 1 1 1 X 2 2 1 2 1 X 1 1 1 1 2 X X X X 1 1 1 1 1 1 1 1

™

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Form (at room temperature unless otherwise stated) Gas Colorless Waxy Solid Colorless crystal or Powder Clear petroleum distillate White Powder Liquid Colorless Oily Liquid Liquid Liquid Liquid In Water Colorless Liquid Yellow Crystals Yellow Oily Liquid Colorless Gas or Liquid Colorless Liquid Colorless Gas Solid Colorless Water Solution Colorless Liquid Colorless Water Solution Colorless Water Solution Colorless Liquid Colorless to Brown Solution Colorless Liquid Colorless to Brown Oily Liquid Colorless Liquid Colorless to Brown Oily Liquid Colorless to Dark Brown Oily Liquid Colorless Liquid Colorless Liquid Liquid Liquid Liquid Liquid Liquid Viscous Liquid

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

Chemical

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Steam Stearic Acid (Octadecanoic Acid) Stearin Stoddard Solvent STPP (Sodium Tripolyphosphate) Straight Synthetic Oils Styrene (Monomer) Sucrose Solutions Sugar, Liquid, Blended Sugar, Syrup Sulfamic Acid Sulfamic Acid (10%) (Under 170°F/77°C) Sulfate Liquors (Under 150°F/66°C) Sulfur (Under 200°F/93°C) Sulfur Chloride Sulfur Dioxide Sulfur Dioxide (Dry) Sulfur Dioxide (Liquid) Sulfur Dioxide (Moist) Sulfur Hexaflouride (Gas) Sulfur Trioxide (Dry) Sulfuric Acid (10%) Sulfuric Acid (100%) Sulfuric Acid (30%) Sulfuric Acid (50%) Sulfuric Acid (60%) (48.5 deg Baume) Sulfuric Acid (75%) Sulfuric Acid (88%) (64.7 deg Baume) Sulfuric Acid (93%) Sulfuric Acid (96%) Sulfuric Acid (98%) Sulfuric Acid, Fuming (Oleum) Sulfurous Acid (10%) Sulfurous Acid (75%) Sun R&O Oils Suntac HP Oils Suntac WR Oils Sunvis Oils 700, 800, 900 Synthetic Oil (Citgo) Syrup

Couplings / Adapters

G ates Hose / Polymers

T Tall Oil Tall Oil (Under 150°F/66°C) Tallow Tannic Acid Tannic Acid (10 %) Tar (Bituminous) (Under 100°F/38°C) Tar Oil Tartaric Acid TEA (Triethanolamine)

Black liquid Liquid White to clear Solid or Liquid Faint Yellow Powder Yellow Liquid Yellow to dark brown Liquid White Crystalline Powder Colorless Viscous Liquid

1 2 2 X X 2 2 2

X X 2 2 X 2 2

X 2 2 2 2 2 2 2

X X 2 1 X X 1 2

2 1 1 1 1 1 X

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 205

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Couplings / Adapters

Butyl

Fluorocarbon

X X X X X X X X X X X X X X X X X X X X X X X 2 X 2 X 2 2 2 X

X X X X 2 X X X X X X 2 X X X X X X X X X X 1 X X X X X 2 X 2 2 X 2 2 X X

X X X X X 2 X X X X X X X X X 2 2 X X X X 2 X 2 X X 2 2 X

X X X X X X 1 2 X X 2 2 X X 2 X X X X X X 2 X X X X X 2 2 X 2 2 X 2 2 2 X

1 1 1 1 2 1 1 1 2 1 2 1 1 1 1 2 2 1 X 1 2 1 1 1 1 1 2 1 1 1 1 X 2 2 1 1 1 X 1 1

Polypropylene

Neoprene

2 1 1 2 2 2 X X X 2 X X 2 X X X X X X X 1 1 X X X X X 2 X 2 2 2 X X 2 2 2

Brass

X X X X X 2 X X 2 X X X 2 X X X X X 2 X X X 1 1 2 1 X 2 2 1 X

Aluminum

SBR

X X X 2 X X X X X X 1 X 2 X

Stainless Steel 316

Stainless Steel 304

Iron/Carbon Steel

PVC

Nylon

CPE

Hypalon

NBR

EPDM

Food & Bev. Mstr.

X 2 X X 2 X X X X 2 X X X X X X X X X X X X X 2 2 2 X 2

1 X X X 1 1 1 X 2 X 2 1 1 1 -

2 1 1 2 1 2 1 1 2 1 1 1 1 1 2 2 X 2 1 X 1 X -

1 2 2 2 X 1 X X X X X X 2 X 2 X X 1 2

1 1 2 2 1 2 1 1 1 1 1 1 1 1 1 X 1 X X 1

1 1 1 1 2 1 1 1 1 1 1 1 1 1 2 1

1 1 1 1 2 1 1 1 1 1 1 1 2 1 1 1 1 1

1 X 1 1 1 X X X X X X 1

1 2 X 1 1 1 1 1 1 1 X X 1

X X X 2 1 1 -

X 2 2 2 2 X X X X 1 X 2 X X -

UHMWPE

2 1 1 2 1 2 X 2 2 X 1 X 2 2 2 2 1 1 1 1 2 X 1 1 1 2 2 2

™

Gatron

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

™

Form (at room temperature Chemical unless otherwise stated) TEL (Tetraethyl Lead) Colorless Oily Liquid Tellus Oils Liquid Tenol Oils Liquid Tergitol (Ethoxylates and Ethoxysulfates of Alcohol) Terpineol Colorless Liquid or Crystal Tertiary Butyl Alcohol Colorless Liquid or Crystal Tetrachlorobenzene White Crystal Tetrachloroethane (Acetylene Tetrachloride) Colorless Liquid Tetrachloroethylene Colorless Liquid Tetrachloromethane Colorless Liquid Tetrachloronaphthalene Oily Liquid to Crystaline Solid Tetradecanol White Solid Tetraethyl Lead (TEL) Colorless Oily Liquid Tetraethylene Glycol Colorless Liquid Tetrahydrofuran (THF) Colorless Liquid Tetrahydroxydicyclopentadiene (JP 10) Tetralin Colorless Liquid Theobromo Oil (Cocoa Butter) Liquid above 95°F (35°C) THF (Tetrahydrofuran) Colorless Liquid Thiopen Tin Tetrachloride Colorless Liquid Titanium Tetrachloride Colorless Liquid Toluene (Toluol) (Methyl Benzene) Colorless Liquid Toluene Diisocyanate (Hylene) Yellow Liquid Toluene Diisocyanate (Isocyanate) Water White to Yellow Liquid Toluidine Yellow Liquid or White Crystal Toluol (Toluene) Colorless Liquid Transformer Oil (Askarel Types)1 Liquid Transformer Oil (Petroleum Type)1 Liquid Transmission Fluid (Type A) Liquid Tributoxyethyl Phosphate Yellow Liquid Tributyl Phosphate Colorless Liquid Tricalcium Aluminate (Calcium Aluminate) Crystals or Powder Trichlorobenzene White Crystal or colorless Liquid Trichloroethane 1,1,1 (Methyl Chloroform) Colorless Liquid Trichloroethylene Colorless Liquid Trichloropropane Colorless Liquid Tricresyl Phosphate Colorless Liquid Triethanolamine (TEA) Colorless Viscous Liquid Triethylamine Colorless Liquid Triethylene Glycol Colorless Liquid Trihydroxybenzoic Acid (Gallic Acid) In Alcohol or Glycerol Trimethyl Phosphite Colorless Liquid Trimethylbenzene (Mesitylene) Liquid Trinitrophenol (Picric Acid) Yellow Crystals Trioctyl Phosphate Liquid Triphenyl Phosphate Colorless Powder Tripolyphosphate (STPP), (Sodium) White Powder Trisodium Phosphate (TSP) Colorless crystal Tung Oil Yellow drying oil 1 Petroleum hose only. 2Aircraft fueling hose only for fueling operations.

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

Sanitron

T K

™

Renegade

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Stallion ® Mustang

G ates Hose / Polymers

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. Gates Corporation 206

39496-000 July 30, 2009 Supersedes 39496-000 July 30, 2007

Industrial Hose Products Contact Denver Product Application for recommendations for chemicals not listed. Phone (303) 744-5070

Food & Bev. Mstr.

CPE

Nylon

PVC

Iron/Carbon Steel

Stainless Steel 304

Stainless Steel 316

Aluminum

Brass

Polypropylene

Hypalon

Fluorocarbon

Butyl

Neoprene

SBR

NBR

Sanitron

EPDM

UHMWPE

Gatron

™

Renegade

T K

(at room temperature unless otherwise stated) Liquid oil 1

™

Form

Teflon /Neoflon

NOTE: Ratings are for the effect on the polymer only !

Chemical

Stallion ® Mustang

1 = Preferred - Constant Contact 2 = Acceptable - Intermittent Contact X = Not Recommended – = No Data

Turpentine

Couplings / Adapters

G ates Hose / Polymers

U Ucon Hydrolube Types 150CP, 200CP Ucon Hydrolube Types 275CP, 300CP, 550CP Ucon M1 Undecanol (Undecyl Alcohol) Undecyl Alcohol (Undecanol) Union Hydraulic Tractor Fluid Urea Solution (100%)

Liquid Liquid Liquid Colorless Liquid Colorless Liquid Brown Liquid Liquid

1 1 1 1 1 1 1

1 1 1 1

1 1 X -

1 1 1 1 1 1 2

X 1

X 2 2 1

1 X 1 X 2

1 2 2 -

2 2 1

1 2 1 1 1

2 2 2 2 2

1 1 1 1

1 1 1 -

Liquids Liquid Brownish to colorless Liquid Colorless Liquid Colorless Gas Colorless Liquid Liquid Colorless Liquid

1 1 1 1 1 1 1 1 1 1

2 1 1 2 1 1 1

1 X -

X 2 1 2 X X

X 2 2 X X X X X

X 2 2 X X X 1 1

X X 2 2 X X X X

X 2 2 2 X X X -

X X 2 2 2 X X X X

2 1 1 X 2 1 1 1

X 1 2 X X X X X

1 2 1 X X -

1 1 1 X 1 1

2 2 1 X X 2 -

2 1 1 X 2 1 1

1 1 1 2 1 1 1 1

1 1 1 1 2 1 1 1

1 1 X 1 1 2

2 1 X 2 X 1

Liquid to semi-Solid paste Liquid Liquid Liquid Liquid Liquid Liquid Liquid Liquid Liquid Liquid

1 1 1 1 1

1 1 1

1 1 1 1

1 1 1

1 1 -

1 1 1

1 -

1 1 1

1 1 1 1 1

1 1 2 1

1 1 -

1 2 1 -

X X

1 1 1 1 1 2 1 1 2 1 1 1 1 2 1 USE FDA HOSE ONLY X X X X X 1 X X 2 X

1 1

X 2

1 1

1 1 1 1

1 1 1

2 2 -

1 2 -

1 1 -

1 -

1 1 1 -

Colorless Liquid White solid, liquid @ 68°F (20°C)

1 1

2 1

X -

1 1

X -

White Crystal Colorless to cloudy Liquid Yellow Solid White or gray Powder Colorless to cloudy Liquid

1 1 1 1 1 1 1

1 1 1 1 1

1 -

X 2 2

1 X 1 2

2 2 X

X 1 2

X 2 2 2

X 1 -

X 1 1 2

1 1 1

2 X 1 2

2 1 2 1 1 2

1 X X

1 2 1 2

1 1 1 1

1 X X

V Varnish Vegetable Oils Versilube F-50, F-44 Vinegar Vinyl Acetate Vinyl Chloride (Monomer) Vinyl Fluoride Vinyl Trichloride (Trichloroethane) Vitrea Oils VM&P Naptha (Mineral Spirits)

W Waste Paint Water Water (Brine) Water (Deionized) Water (Distilled) Water (Potable) Water Glycols Water in Oil Emulsions White & Bagley No. 2190 Cutting Oil Wines Wood Oil

X Xylene (Dimethylbenzene) Xylenol (Dimethylphenol)

Z Zeric Zinc Acetate Zinc Chloride Solutions Zinc Chromate Zinc Hydrate Zinc Oxide Zinc Sulfate Solutions

Due to continual product improvements, Gates reserves the right to alter specs and prices without prior notice. The world’s most trusted name in belts, hose and hydraulics. 207

2009 GATES INDUSTRIAL HOSE, COUPLINGS & EQUIPMENT

The Worldâ&#x20AC;&#x2122;s Most Trusted Name in Belts, Hose and Hydraulics.

Your Local Distributor:

Gates Corporation 1551 Wewatta Street | P.O. Box 5887 | Denver, CO 80217-5887 (800) 366-3128 | Fax (303) 744-4499 www.gates.com/industrialhose

39496-000 October 2009

Hose, Couplings & Equipment