A L U M I N U M & E X T R U S I O N S
F O R T H E S I G N I N D U S T R Y
ITEM- NUMBER
DESCRIPTION
ITEM- NUMBER
DESCRIPTION
ALUMINUM
2T12520020020
TUBE ⅛” x 2” x 2” x 20’ ALUM.
2T12520020020
TUBE ⅛” x 2” x 2” x 20’ ALUM.
2T12512512520
TUBE ⅛” x 1¼” x 1¼” x 20’ ALUM.
2T12512512520
TUBE ⅛” x 1¼” x 1¼” x 20’ ALUM.
2T12515015020
TUBE ⅛” x 1½ x 1½ x20’ ALUM.
2T12515015020
TUBE ⅛” x 1½ x 1½ x 20’ ALUM.
2TO6315015020
TUBE 1/16” x 1½ x 1½ x 20’ ALUM.
2TO63115015020
TUBE 1/16” x 1½ x 1½ x 20’ ALUM.
2TO6310010020
TUBE 1/16” x 1” x 1” x 20’ ALUM.
2TO6310010020
TUBE 1/16” x 1” x 1” x 20’ ALUM.
2TO6320020020
TUBE 1/16” x 2“ x 2” x 20’ ALUM.
2T12510010020
TUBE ⅛” x 1” x 1” x 20’ ALUM.
2T12510020020
TUBE ⅛” x 1” x 2” x 20’ ALUM.
2T12507515020
TUBE ⅛” x ¾” x ¾ “ x 20’ ALUM.
2T06307507520
TUBE 1/16” x ¾” x ¾” x 20’ ALUM.
2T12520020010
TUBE ⅛” x 2” x 2” x 10’ ALUM.
2T06307507510
TUBE 1/16” x ¾” x ¾” x 10’ ALUM.
2T06310010010
TUBE 1/16” x 1” x 1 “ x 10’ ALUM.
2T12515015010
TUBE ⅛ X 1½” x 1½” x 10’ ALUM.
2T06315015010
TUBE1/16 x 1½” x 1½” x 10’ ALUM.
212507515010
TUBE ⅛ x ¾” x 1½” x 10’ ALUM.
212510020010
TUBE ⅛ x 1” x 2” x 10’ ALUM.
212510010010
TUBE ⅛ x 1” x 1” x 10’ ALUM.
2T06320020010
TUBE1/16 x 2” x 2” x 10’ ALUM.
ITEM- NUMBER
DESCRIPTION
Custom cutting available ITEM- NUMBER
DESCRIPTION
2CS-MFTS6
Monoclic Spring
2CSS-10-3-20
CSS-10-3x20’ B-Lite Gold
2CS-ERP11
Easyclic Spring Rear Profile
2CSS-11-4-20
CSS-11-4x20’ B-Lite Chrome
2CS-ELP13
Monoclic Corner Angle
2CSS-11-3-20
CSS-11-3x20’ B-Lite Gold
2CS-EFT12
Easyclic Spring Front Trim
2CSS-11-1-20
CSS-11-1x20’ Mill Finished
2CSS-12-3-20’
CSS-12-3-20’ B-Lite Gold
2CSS-16-26’1”
CSS-16x26’1” 6063 T-5
2CSS-15-26’1”
CSS-15x26’1” 6063 T-5
2CSS-14-1-20
CSS-14 1x20’ Mill Finished
2CSS-13-1-20
CSS-13 1x20’ Mill Finished
2CSS-13-1-20
CSS-13 1x20’ Mill Finished
ITEM- NUMBER
DESCRIPTION
2BAR12510020
Rect. Bar ⅛” x 1” x 20’
2BAR18812520
Rect. Bar 3/16” x 1” x 20’
ALUMINUM
ITEM- NUMBER
DESCRIPTION
ITEM- NUMBER
DESCRIPTION
2A18810010020
ANGLE 3/16” x 1” x 1” x 20’ ALUM.
2A12520020010
ANGLE ⅛” x 2“ x 2” x 10’ ALUM.
2A18820020020
ANGLE 3/16” x 2” x 2” x 20’ ALUM.
2A18820020020
ANGLE 3/16” x 2” x 2” x 10’ ALUM.
2A12520010020
ANGLE ⅛” x 1½” x 1½” x 20’ ALUM.
2A12520010010
ANGLE ⅛” x 2” x 1” x 10’ ALUM.
2A06320020020
ANGLE 1/16” x 2” x 2 “ x 20’ ALUM.
2A06310010010
ANGLE 1/16” x 1” x 1 “ x 10’ ALUM.
2A12507507520
ANGLE ⅛ x 3/4” x 3/4” x 20’ ALUM.
2A12515015010
ANGLE ⅛ x 1½” x 1½” x 10’ ALUM.
2AO6315015020
ANGLE 1/16” x 1½“ x 1½” x 20’ ALUM.
2AO6315015010
2A06307507520
ANGLE 1/16” x 1½“ x 1½” x 10’ ALUM.
ANGLE 1/16 x ¾” x ¾ “ x 20’ ALUM.
2A12507507510
ANGLE ⅛ x ¾” x ¾” x 10’ ALUM.
2A37550050025
ANGLE ⅜” x 5” x 5” x 25’ ALUM.
2A12510010015
ANGLE .125 x 1” x 1” x 15’ ALUM.
2A37560040025
ANGLE ⅜” x 6” x 4” x 25’ ALUM.
2A06305005010
ANGLE 1/16 x ½” x ½” x 15’ ALUM.
2A37560060025
ANGLE ⅜” x 6” x 6 “ x 25’ ALUM.
2A06307507510
ANGLE 1/16 x ¾” x ¾” x 10’ ALUM.
2A25020020020
ANGLE ¼ x 2” x 2” x 20’ ALUM.
2A06320020010
ANGLE 1/16 x 2” x 2” x 10’ ALUM.
2A12520020020
ANGLE ⅛” x 2“ x 2” x 20’ ALUM.
2A12515015020
ANGLE ⅛” x 1½” x 1½” x 20’ ALUM.
2A125210010020
ANGLE ⅛” x 1” x 1” x 20’ ALUM.
2A06310010010
ANGLE 1/16” x 1” x 1 “ x 10’ ALUM.
2A06305005020
ANGLE 1/16 x ½” x ½” x 20’ ALUM.
2A06307507508
ANGLE 1/16 x ¾” x ¾” x 8’ ALUM. 2RT250035144
Drawn .250 x.035 x 144 3003 H14
PLANCHAS DE ALUMINIO APLICACIONES: R贸tulos, Paneles, Exhibidores POP, Cajas Lum铆nicas, Vallas.
EXTRUSIONS
ALUMINUM SHEETS
ITEM-NUMBER
280-48144-111 280-48120-111 280-48096-111 263-48144M111 263-48120M111 263-48120-111 263-48096M111 263-48096-111 250-48144-111 250-48120-111 250-48096-111 240-60144-111 240-60120-111 240-48144-111 240-48144M111 240-48120M111 240-48120-111 240-4896M111 240-48096-111 232-60144-111 232-60096-111 232-60096M111 232-60120-111 232-60120M111 232-48120M111 232-48144-111 232-48144M111 232-48120-111 232-48096-111 240-60096-111 263-60096M111 263-60120M111 263-60144M111
DESCRIPTION
CLASS-CODE
.080x48x144 White /white .080x48x120 White /white .080x48x96 White /white .063x48x144 White Masked .063x48x120 White/white Masked .063x48x120 White Un Masked .063x48x96 White/white Masked **USAR 63-48096M111***** .050x48x144 Masked White/white .050x48x120 Masked White/white .050x48x96 Masked White/white .040x60x144 White/ White .040x60x120 White /white .040x60x144 White /white .040x60x144 White /white Masked .040x60x120 Masked White /white .040x60x120 White /white .040x60x96 Masked White /white .040x60x96 White /white .032x60x144 White /white .032x60x96 White /white .032x60x96 White /white Masked .032x60x120 White /white .032x60x120 White /white Masked .032x48x120 Masked White /white .032x48x144 White /white .032x48x144 Masked White /white .032x48x120 White /white .032x48x96 White /white .032x60x96 White /white .063x60x96 White /white Masked .063x60x120 White /white Masked .063x60x144 White /white Masked
ITEM-NUMBER
DESCRIPTION
263-48120-102 250-48120-101 240-48120-131 240-48120-156 240-48120-171 240-48120-193 240-48120-105 240-48120-101 240-48120-103 240-48120-104 240-48096-131 240-48096-156 240-48096-171 240-48096-110 240-48096-101 240-48096-102 240-48096-103 240-48096-104 240-48096-235 240-48120-235
.063x48x120 .050x48x120 .040x48x120 .040x48x120 .040x48x120 .040x48x120 .040x48x96 .040x48x120 .040x48x144 .040x48x120 .040x48x96 .040x48x144 .040x48x96 .040x48x96 .040x48x96 .040x48x96 .040x48x96 .040x48x96 .040x48x96 .040x48x120
100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100
CLASS-CODE
Matte Black /white Raven Black /white Red /white Caut. Yellow/ White Ivy Green/white Brigth Puple/white Orange/white Raven Black/white Heron Blue/white Heron Blue/heron Red/white Caut. Yellow/ White Ivy Green/white Raven Black/black Raven Black /white Matte Balck /white Heron Blue /white Hero Blue/hero Med Gray/charco Med Gray/charco
101 101 101 101 101 101 101 101 101 101 101 101 101 101 101 101 101 101 101 101
ITEM-NUMBER
290-48096-400 290-48120-400 290-48144-400
ESPESOR ALTO ANCHO
.090 x 48 x 96 .090 x 48 x 120 .090 x 48 x 144 .080 x 60 x 96 .080 x 60 x 120 .080 x 60 x 120 .080 x 48 x 144 .080 x 48 x 144 .080 x 48 x 96 .080 x 48 x 120 .080 x 48 x 120 .080 x 36 x 144 .080 x 48 x 96
263-60144-52 263-60096-52 263-60120-52 263-48144-52 263-48120-52 263-48096-52 236-36096-52 263-36120-52 263-36144-52
.063 x 60 x 144 .063 x 60 x 96 .063 x 60 x 120 .063 x 48 x 144 .063 x 48 x 120 .063 x 48 x 96 .063 x 36 x 96 .063 x 36 x 120 .063 x 36 x 144
263-48144-400 263-48120-400 263-48096-400 263-36144-400
.063 x 48 x 144 .063 x 48 x 120 .063 x 48 x 96 .063 x 36 x 144
250-48144-400 250-48144-52 250-48120-400 250-48120-52 250-48096-400 250-48096-52 250-36096-52 250-36120-52 250-36144-52
.050 x 48 x 144 .050 x 48 x 144 .050 x 48 x 120 .050 x 48 x 120 .050 x 48 x 96 .050 x 48 x 96 .050 x 36 x 96 .050 x 36 x 120 .050 x 36 x 144
240-48144-400 240-48120M400 240-48120-400 240-48096M400 240-48096-400 240-36120-400
.040 x 48 x 144 .040 x 48 x 120 .040 x 48 x 120 .040 x 48 x 96 .040 x 48 x 96 .040 x 36 x 120
232-48120-400 232-48096-400 232-36120-400
.032 x 48 x 120 .032 x 48 x 96 .032 x 36 x 120
2250-48096-40
.025 x 48 x 96
216-34076-400 216-36076-400
5052 5052 5052 5052 5052 5052 5052-H32 5052-H32 5052-H32 5052-H32 5052-H32 5052-H32 5052 5052 5052
ITEM-NUMBER
ESPESOR ALTO ANCHO
2190-48120-40 2188-48120-40 2188-48096-40
.190 x 48 x 120 .188 x 48 x 120 .188 x 48 x 96
2125-60192-52 2125-60120-52 2125-60144-52 2125-60156-52 2125-60096-52 2125-48168-52 2125-48144-40 2125-48144-52 2125-48156-52 2125-48096-40 2125-48096-52 2125-48120-40 2125-48120-52 2125-36120-52 2125-36144-52 2125-48180-52
.125 x 60 x 192 .125 x 60 x 120 .125 x 60 x 144 .125 x 60 x 156 .125 x 60 x 96 .125 x 48 x 168 .125 x 48 x 144 .125 x 48 x 144 .125 x 48 x 156 .125 x 48 x 96 .125 x 48 x 96 .125 x 48 x 120 .125 x 48 x 120 .125 x 36x1 20 .125 x 36 x 144 .125 x 48 x 180
26061T6
1/2” x 48 x 144 ALUM. PLATE
2250-48192-6061 2125-48096-3003 2188-48192-3003
4’ x 16’ ALUM. BRHIGT TREAD PLT 4’ x 8’ ALUMBRIGHT TREAD PLT 4’ x 16’ ALUM. BRHIGT TREAD PLT
COLOR
5052 5052 5052 5052 5052 5052 5052 5052
1
ALUMINUM
280-60096-52 280-60120-400 280-60120-52 280-48144-400 280-48144-52 280-48096-52 280-48120-400 280-48120-52 280-36144-52 280-48096-400
COLOR
5052 5052 5052
5052 5052 5052 5052 5052 5052
.016 x 34 x 76 MILL FINISHED 30 .016 x 34 x 76 MILL FINISHED 30
ITEM-NUMBER 240-48120M231
ESPESOR ALTO ANCHO
240-48120M235 240-48120-230
.040 x 48 x 120 MIRROR CLEAR .040 x 48 x 120 B.B. CLEAR ANODIZED .040 x 48 x 120 CLEAR SATIN ANODIZED
240-48120M236 240-48120-232
.040 x 48 x 120 B.B. GOLD ANODIZED .040 x 48 x 120 GOLD SATIN ANODIZED
240-48096-240
.040 x 48 x 96
BRONZE ANODIZED
COLOR
ALUMINUM ITEM- NUMBER
DESCRIPTION
Custom cutting available
2SIGNCOMP2075
2¼” Retainer 24’5”
2SIGNCOMP2055
1½” Retainer 24’5”
2SIGNCOMP2056-20
Econo Molding 20’
2SIGNCOMP2056
Econo Molding 24’5”
2SIGNCOMP5116
040 x 10 x ¼ WB Raceway Cover
2SIGNCOMP2056P
Econo Molding 24’5”
2SIGNCOMP4580
Signcomp R/C Sing Face Bleed
2SIGNCOMP2034
Single Face Filler 24’5” Econ.
2SIGNCOMP4000
Signcomp Single Face Body 9” R
2SIGNCOMP2034P
Single Face Filler 24’5” Econ.
2SIGNCOMP1985
Socket Raceway 24’5”
2SIGNCOMP1987
Transformer Raceway Cover 24’2”
2SIGNCOMP1986
Socket Raceway Cover 24’2”
2SIGNCOMP1948
¾” Wall Frame 24’2”
2SIGNCOMP1949
1¼” Wall Frame 24’2”
2SIGNCOMP1981
2 PC Trans Raceway-Front 24’2”
2SIGNCOMP2075
2¼ Dual Frame Cover 24’5”
2SIGNCOMP1982
2 PC Trans Raceway-Back 24’2”
2SIGNCOMP1986
Transformer Raceway Cove 24’2”
2SIGNCOMP4540
Signcomp R/C Med. Body Dual
2SIGNCOMP4550
Signcomp R/C Med. B Bleed
2SIGNCOMP4560
Single Face Body 9” R/C
2SIGNCOMP4220
Signcomp 2.25 Dual Rad. Cover
2SIGNCOMP4260P
Signcomp Bleed Tension Cover
2SIGNCOMP4280
Signcomp 1.5” Retainer R/C
2SIGNCOMP4200
Signcomp Dual Frame R/C
2SIGNCOMP2122
Bleed Retro Frame Cover 24’5”
2SIGNCOMP2128
2¾” Divider 24’5”
2SIGNCOMP4280
Signcomp 1.5” Retainer R/C
2SIGNCOMP1941
2 Part Large Outer Frame 24’5”
2SIGNCOMP1959
2 Part Large Inner Frame 24’6”
2SIGNCOMP1989
Trans Raceway Mounting Clip
2SIGNCOMP5290-1
Raceway Cvr.Screw 2Pt Retainer
2SIGNCOMP1007
DESCRIPTION S1 3¼” ROUND POST 24’
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP1210
S3 3¼” RADIUS POST 24’
ITEM- NUMBER
DESCRIPTION
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP1100
S2 2” SQUARE POST 24’
2SIGNCOMP1233
S3 3¼” SQUARE POST 24’
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP1260
S3 3¼” SLIDE BODY 24’2”
ITEM- NUMBER 2SIGNCOMP1120
DESCRIPTION
EXTRUSIONS
ITEM- NUMBER
S2 BLEED BODY 24’ 2”
ITEM- NUMBER
DESCRIPTION
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP1200
S2/S3 REVEAL 24’
2SIGNCOMP1270
S3 3¼” BLEED BODY 24’2”
EXTRUSIONS
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP1500
S7 7” RADIUS POST 24’
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP1510
S7 7” RECTANGULAR POST 24’
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP1592
S7 HINGE BODY 24’2”
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP1662
1 1¼DIVIDER 24’
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP1666
INSERT RETAINER 16’1”
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP1550
S7 REVEAL 24’
ITEM- NUMBER
DESCRIPTION
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP1570
S7 7” BLEED BODY 24’2”
2SIGNCOMP1668
INSERT DIVIDER 16’
EXTRUSIONS
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP1671
6” RADIUS ¼ ROUND END 24’2”
7-1/2” 1/4”
1/4” Joiner Bracket
1/4” Corner Angle Slot
1/4” Steel Mounting Plate 5-3/16”
W ater Relief Channel
Raceway Cover Ta b
Inner Body Flanges
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP2015
MEDIUM BODY 24’5”
3/8” Oversized Hole 10-3/4”
1/4” Joiner Bracket Slot
Ballast Bracket Slots
1/4”
8-7/16”
Raceway Cover Ta b
Hinge Screw
Part #5170
W ater Relief Channel
Inner Body Flanges
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP2005
WIDE BODY 24’ 5”
1/4” Corner Angle Part #5312
Closure Screw
Part #5180
1-3/4”
1-11/16”
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP2040
RETRO BODY 24’5”
Corner Angle Screw
Part #5218
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP1592
S7 HINGE BODY 24’2”
ITEM- NUMBER
DESCRIPTION
2SIGNCOMP1668
INSERT DIVIDER 16’
T E N S I O N I N G
S Y S T E M S
F O R
F L E X I B L E
F A C E S
EXTRUSIONS
Sign Cabinet Body Extrusions Single Face Body 24’5” 2SIGNCOMP2025
6-1/8”
Retro Body 24’5”
1/4”
2SIGNCOMP2040
3-15/16” .040 aluminum back
Hinge Screw 2SIGNCOMP5170
1-3/4”
1-11/16”
Medium Body Part #2015
7-1/2”
1/4” 5-3/16” Screw 2SIGNCOMP5170
Wide Body 24’5” 2SIGNCOMP2005
10-3/4”
1/4” 8-7/16”
Hingeable Retainer Extrusions Bleed Tension Frame Cover 24’5” 2SIGNCOMP2095
Tension Frame 24’5”
Dual Frame 24’5”
1½” Tension Frame Cover
2¼” Dual Frame Cover
2SIGNCOMP2065
2SIGNCOMP2085
2SIGNCOMP2084
2SIGNCOMP2075
Frame Brace 2SIGNCOMP5350
Frame Support Tube 2SIGNCOMP2175
Frame Brace 2SIGNCOMP5350
Frame Support Tube 2SIGNCOMP2175
T E N S I O N I N G
S Y S T E M S
F O R
F L E X I B L E
F A C E S
2” Retro Frame 24’5”
EXTRUSIONS
Retro Frame Extrusions Bleed Retro Frame
2SINGCOMP2112
2SIGNCOMP2105
2-3/8” Retro Frame Cover
2SIGNCOMP2115 (Optional Brake Form Cover)
Frame Brace 2SIGNCOMP5350
Frame Support Tube 2SIGNCOMP2175
Frame Brace 2SIGNCOMP5350
Flat Bleed Retro Frame
Wall Mount Retro Frame
Flat Bleed Retro Frame Cover
Wall Mount Retro Frame Cover
Part #2104
Frame Support Tube 2SIGNCOMP2175
2SIGNCOMP2090
Part #2121
NOTE: Wall Mount Retro Tensioning Tool, 2sigcomp5137 required.
2SIGNCOMP2091
Flat Bleed Retro Frame
Flat Bleed Retro Frame
Extended Bleed Retro Cover
1-1/2” Flat Retro Frame Cover
Part #2104
Part #2104
Part #2123
Part #2125
Retro Fascia Frame Extrusions Bleed Fascia Frame 24’ 5”
1-1/2” Fascia Frame 24’5”
Part 2SIGNCOMP2092
(Optional Brake Form Cover)
2SIGNCOMP2094
Cover Screw 2SIGNCOMP5195
Corner Key 2SIGNCOMP5210
(Optional Brake Form Cover)
Frame Corner Angle 2SIGNCOMP5305 Corner Key 2SIGNCOMP5210
Cover Screw 2SIGNCOMP5195
T E N S I O N I N G
S Y S T E M S
F O R
F L E X I B L E
F A C E S
EXTRUSIONS
Divider Bar Dual Divider 24” 2SIGNCOMP2142
2-1/2” Dual Divider Cover
2SIGNCOMP2146
6” & 9” Radius Cast Aluminum Corners Medium Body
Wide Body
Single Face Body
Dual Frame
with 2-1/4” Dual Frame Cover
Tension Frame
with Bleed Tension Frame Cover
NOTE: The hingeable body and frames are cast aluminum 2-1/4” Dual Frame Cover and Bleed Tension Frame Covers are injection molded polycarbonate, pre-primed ready for paint/top coating.
Hingeable Systems Configurations Medium Body
Single Face Body
Retro Body
13-3/4”
17”
9-1/4”
4-7/8”
Tension Frame
14”
17-1/4”
9-3/8”
4-15/16”
Tension Frame
14-1/2”
17-3/4”
9-5/8”
5-3/16”
Dual Frame
Wide Body
with 2-1/4” Dual Frame Cover
with Bleed Tension Frame Cover
with 1-1/2” Tension Frame Cover
T E N S I O N I N G
S Y S T E M S
F O R
F L E X I B L E
F
A C E S
EXTRUSIONS
The very best flexible face tensioning system. Easy to use:
Tension Clip
1. FOLD fabric over mandrel. 2. SNAP clip onto mandrel & fabric. 3. INSERT Tension Clip with fabric into either retro frame or hingeable frame. * * * *
2SIGNCOMP5360
No holes to drill. No fasteners required. Easy to adjust and will not migrate. Absolutely no slippage . Clips attach to fabric, face side up. Once attached, faces may be rolled for transport or storage. Simple to tension, quick to release. The Tensioning Tool allows for easy and controlled tensioning force. Tension Clips release from the extruded frame with a standard slotted screwdriver .
Tension Clip Body
Tension Clip Mandrel Face Side Up
of
Side Profile Tension Clip with Fabric
T ool
Tension Clip Mandrel
Tensioning
1. FOLD
T ool Wall Mount Tensioning
Tension Clip Body
2. SNAP
3. INSERT Shown in Retro Frame Part #2112
UL Recognized
Component
System:
The Under writers Laboratory file number is (E136850).
S I G N
E X T R U S I O N S
A N D
S Y S T E M S
EXTRUSIONS
Tensioning System Instructions 2.) Fold the fabric over the mandrel.
D. Tension Clip Attachment 1.) Place the mandrel, smooth side up, on the fabric just inside the clip placement line.
(Illus. 5)
(Illus. 3.)
Illus. 5
3.) Rotate the fabric and mandrel for ward by lifting the edge nearest you to stand the mandrel and fabric up on its edge. (Illus. 6)
Illus. 3
IMPORTANT - Tension Clips are attached to the fabric graphic side up.
NOTE - The Tension Clip is comprised of two components: The Tension Clip Body and the Tension Clip Mandrel. (Illus. 4) Illus. 6
Tension Clip Body
4.) With the SignComp logo facing toward you, use thumb pressure to drive one end of the clip body down on to the mandrel and fabric. (Illus. 7 & 8) (4)
(5) Tension Clip Mandrel
Illus. 4
Illus. 7
S I G N
E X T R U S I O N S
A N D
S Y S T E M S
E. Tension Clip Placement
EXTRUSIONS
Tensioning System Instructions (Illus. 10)
For: Dual Frame, 2” Retro Frame and 1-1/2” Fascia Frame. Place Tension Clips approximately 6” on center .
5.) Using palm pressure, drive the remaining end of the clip body down onto the mandrel and fabric.
1-1/2” Fascia Frame Part #2094
(Illus. 7, 8, & 9.)
Dual Frame Part #2065
2” Retro Frame Part #2112
For: Tension Frame, Bleed Retro Frame, Flat Bleed Retro Frame, Dual Divider and Bleed Fascia Frame. Place Tension Clips approximately 5” on center .
Bleed Fascia Frame Part #2092
Tension Frame Part #2085
Bleed Retro Frame Part #2105
Flat Bleed Retro Frame Part #2104
Dual Divider Part #2142
Illus. 8
Illus. 10
Illus. 9
HINT: Do not try to drive both ends of the clip
body down onto the mandrel and fabric at the same time. Snap one end down then the other end.
HINT - Tension Clip Position may be adjusted with out removing the T ension Clip from the fabric. Slide the clip mandrel in the direction you wish to move the Tension Clip. Follow this by sliding the Tension Clip Body. Repeat this procedure until position adjustment is achieved. HINT - The Tension Clip may be detached from the fabric by pulling the Tension Clip Body straight off and away from the fabric and Tension Clip Mandrel.
S I G N
E X T R U S I O N S
A N D
S Y S T E M S
EXTRUSIONS
Tensioning System Instructions F. Tensioning 1.) Lay the assembled frame flat with the extruded Tension Channel facing up. 2.) Lay the fabric, with the Tension Clips attached, over the assembled frame graphic side up. 3.) Insert the Tension Clips into the Tension Channel of the assembled frame. Work your way around the frame just starting each clip into the extruded frame as shown. (Illus. 12 & 13.) HINT: When pulling on the fabric do not pull directly on the fabric flap or Tension Clip doing so will cause the T ension Clip to pop off. When pulling on the face grasp the fold and pull the face into place.
Illus. 11
4.) Using the Tension Tool, exert a downward for ce onto each Tension Clip, pressing it into the extruded frame as shown. (Illus. 12 & 13.) HINT: Just start the Tension Clips in one or two clicks, working your way around the frame. Go back around a second time and apply tension by driving the Tension Clips down into the frame. Do not over tension . Apply just enough tension to achieve a smooth, flat appearance.
G. Tension Tool Use
Illus. 12 Rotate
Hook the Tension Tool tip under the outside rail of the assembled frame. Slide the Tension Tool along the outside rail. With gentle, consistent pressure, force the Tension Clip into place by pressing the “wings� of the Tension Tool downward onto any portion of the Tension Clip. By pushing or pulling the Tension Tool handle while the Tension Tool tip is inserted under the outside rail, leverage is gained to exert for ce down on to the Tension Clip. (Illus 12 & 13.)
NOTE: Downward pressure may be applied to either end or the middle of the Tension Clip.
Outside Rail
Illus. 13
S I G N
E X T R U S I O N S
A N D
S Y S T E M S
H. Releasing the Tension and Removing the Tension Clip
or
EXTRUSIONS
Tensioning System Instructions (T ilt) (Rotate)
A standard slotted screwdriver is used to release tension from the installed fabric. Insert the tip of the screwdriver into the recess located at the backside of the Tension Clip. Rotate or tilt the screwdriver to separate the Tension Clip teeth away from the extruded teeth within the frame. This will release the tension or allow the Tension Clip to be removed from the frame by prying or pulling the Tension Clip up & out. (Illus. 14 &15.)
1.) Insert the screwdriver tip into the Tension Clip recess.
2.) Rotate or tilt the
screwdriver to release the Tension Clip teeth away from the extruded frame.
3.) Remove Tension Clip
by prying or pulling it out and up from the frame.
Illus. 14
I. References
ST RAI G H T
Illus. 15
ANG L ED
T E N SI O N C H A N N E L FR A M E S
T E N SI O N C H A N N E L FR A M E S
D ual Fram e
Ten sion Fram e
Part #2065
Recess on backside
Tension Clip Body
Part #2085
Important Note: It is important to note the stretch factor of the flexible fabric varies considerably for each brand. When tensioning large sign faces (10’ x 10’ or larger) it is advisable to test the stretch factor by using a strip of the same fabric with one tension clip on each end.
Tension Clip Mandrel
S I G N
E X T R U S I O N S
A N D
S Y S T E M S
EXTRUSIONS
Tensioning System Instructions Befor e beginning, thoroughly read all tensioning instructions. Tools Required: 1. 2.
SignComp Tensioning Tool, part #5135. Pen or marker .
1
3. 4.
2
Flexible Sign Fabric Requirements
ST RAI G H T
FOR:
TENSION CHANNEL FRAMES
1½” Fascia 24’5” Frame 2SIGNCOMP2094
Dual Frame 24’5” 2SIGNCOMP2065
Razor blade or utility knife. Standard slotted screw driver.
2” Retro Frame 24’5” 2SIGNCOMP2112
Dual Divider 24’5” SIGNCOMP2142
Tension Clip Requirements
To determine the approximate number of Tension Clips required, measure the outside dimensions of the assembled sign frame. You will require a minimum of two (2) Tension Clips for ever y perimeter foot. Use 6” on center for straight tension channel frames and 5” on center for angled tension channel frames.
12’
6’ To the outside dimensions of any assembled STRAIGHT TENSION CHANNEL FRAME, add 1-1/2” of flexible fabric to all four sides. (Add a total of 3” of fabric to both the height and width dimensions of the assembled frame.) NOTE: Measure from the center of the Dual Divider .
12’
Outside dimensions = 36’ (perimeter feet) x 12” = 432”. 432” / 6” = 72 Tension Clips for straight tension channel frames. 432” / 5” = 87 Tension Clips for angled tension channel frames.
ANG L ED
FOR:
Example Sign Size
TENSION CHANNEL FRAMES
See page 4, E. Tension Clip Placement for further details. Bleed Fascia Frame 24’5” 2SIGNCOMP2092
Tension Frame 24’5” 2SIGNCOMP2085
Bleed Retro Frame 24’5” 2SIGNCOMP2105
Flat Bleed Retro Frame Part #2104
To the outside dimensions of any assembled ANGLED TENSION CHANNEL FRAME, add 3” of flexible fabric to all four sides. (Add a total of 6” of fabric to both the height and width dimensions of the assembled frame.)
6’
S I G N
E X T R U S I O N S
A N D
S Y S T E M S
3
Basic Instructions
EXTRUSIONS
Tensioning System Instructions HINT: Angled Tension Channel Frames may be
used as a straight edge to draw the clip placement line and trimmed to size fabric line.
A. Trim the flexible sign fabric to size The fabric is to be cut to the appropriate size. See page 1, 1. Flexible Sign Fabric Requirements.
B. Establish the Tension Clip Placement Line
Bleed Fascia Frame 24’5” 2SIGNCOMP2092
Tension Frame 24’5” 2SIGNCOMP2085
Bleed Retro Frame 24’5” 2SIGNCOMP2105
Flat Bleed Retro Frame Part #2104
IMPORTANT - Address the fabric graphic side up.
The clip placement line is to be located on the graphic side of the fabric.
FOR ALL FRAMES:
Draw or drop the clip placement line 1-1/2” in from the edge of the trimmed to size fabric.
HINT : Straight Tension Channel Frames may be
placed on the fabric and traced along the outside perimeter of the frame to establish the clip placement line. Be sure to add 1-1/2” of fabric outside the clip placement line to establish the trimmed to size fabric. (Illus. 1 & 2)
IMPORTANT : Be sure to adjust the position of the angled tension channel frame to accommodate the additional fabric required. See Page 1, 1. Flexible Sign Fabric Requirements. ension NOTE: For Large Applications:
For applications larger than 10’, move the T Clip placement line in approximately 1/4” for ever y 5’ increment. For example a 15’ x 15’ Frame Tension Clips are to be placed approximately 1-3/4” in from the trimmed to size fabric. See page 7, important note.
C. Notch the Corners
1½” Fascia Frame 2SIGNCOMP2094
Dual Frame 24’5” 2SIGNCOMP2065
2” Retro Frame 24’5” 2SIGNCOMP2112
Cut away an approximate 2-1/2” square notch from the fabric edge in each of the four corners of the trimmed to size fabric. HINT :
1½” Tension Clip Placement Line Trimmed to Size Flexible Sign Fabric
Illus. 1
2½” Notched Corner (Discard)
2½”
Illus. 2
1½” ”
2½”
(Graphic Side Up)
Trimmed to Size Flexible Sign Fabric
EXTRUSIONS
SignComp products offer mounting
options
Internal Mounting SystemInboard Posts
Base Plate Mounting
Fabricated base skirts are easily removed for access to mounting plates
Base Plate Mounting
Direct Burial
Wall projection, ceiling mount and sleeve mounting applications are available options
External Mounting SystemOutboard Posts
Base Plate Mounting
Direct Burial W all projection, ceiling mount and sleeve mounting applications are available options
Direct Burial
SignComp’s Insert Panels are: Quickly removable Completely interchangeable Easily replaceable They simply slide in and out after the Insert Panel End Cover is removed. Illuminated applications Non-illuminated applications Hingeable and Non-hingeable aluminum framework Flush frameless appearance Concealed structural divider
Choice of custom size panels
Custom
Panel
Custom height panels may be placed anywhere on the face Insert
Custom
Insert
Panel
Panel
Panel
Choice of three Extruded Aluminum Insert Panels 4”, 6” and 8” or create custom height Aluminum Insert Panels by fixing Top and Bottom Aluminum Insert Adaptors to .090” aluminum sheet * Extruded aluminum * 16’1” extruded lengths * Clear anodized to facilitate the sliding
motion
* For illuminated applications:
Routed out graphics backed with plastic
* For non-illuminated applications:
Painted or applied vinyl graphics
Create custom height Plastic Insert Panels by fixing Top and Bottom Plastic Insert Adaptors to .125” plastic sheet * Extruded modified DR white acrylic * 8’1” extruded lengths * For illuminated applications:
Surface painted opaque background over applied masking films (applied masking films are removed to reveal translucent graphics) * For non-illuminated applications: Painted or applied vinyl graphics
4” Extruded Panels
6” Extruded Panels
8” Extruded Panels
Custom Height Aluminum Panels
Custom Height Plastic Panels
EXTRUSIONS
A simple new approach to flush changeable message panels
EXTRUSIONS
SignComp products offer variety for design applications Series 12 Hinge Body
Part #1612 For low profile, hingeable applications
Adjustable Reveal
6” Radius ¼ Round End
Plan View
Available with or without 6” Radius Ends
2SIGNCOMP1671
Elevation
View
Series 7 Hinge Body 24’2”
2SIGNCOMP1592 For post & panel, hingeable applications
Adjustable Reveal
3 Post Selections
Plan View
Plan View
Elevation
View
Elevation
View
Elevation
View
Series 7 Single Face Hinge Body
Part #1602 For wall mounted, hingeable applications
6” Radius 1/4 Round End 2SIGNCOMP1671
Plan View
Adjustable Reveal
Available with or without 6” Radius Ends
Series 3 Access Body
Part #1290 For non-illuminated,
post & panel applications
Adjustable Reveal
Plan View
8 Post Selections
Series 7/12 Retro Body
Part #1600 For retro fit or custom depth applications
Plan View
Custom depth, hingeable, single or double face applications are achieved by attaching the Series 7/12 Retro Body to fabricated or existing sign cabinet frames.
Insert Panels slide in and slide out after Insert End Cover is removed
Hingeable aluminum framework
Simply remove Insert End Cover to access insert panels Insert Panels are supported the full width by concealed Insert Dividers
End view of Insert Divider
Flush, countersunk stainless steel fasteners hold the Insert End Cover in place Concealed, structural dividers support the Insert Panels Aluminum Insert Panels, Insert Divider and Aluminum Insert Panel Adaptors are supplied clear anodized to facilitate the sliding motion Integrated, hingeable frame allows for easy access for service
EXTRUSIONS
The simplicity of SignComp’s changeable Insert Panels on hingeable aluminum frames
EXTRUSIONS
Available in Series 3, 7 and 12
Series 12 Hinge Body
Series 7 Hinge Body
Part #1612
Series 7 Single Face Hinge Body
Part #1592
Double face, ground mounted, hingeable applications
Double face, post & panel, hingeable applications
Part #1602
Single face, wall mounted, hingeable applications
2-5/16
Series 7/12 Retro Body Part #1600
The Insert Panel System easily integrates with: 12 Hinge Body 7 Hinge Body 7 Single Face 3 Access Body 7/12 Retro Body
Choice of two End Covers Insert End Cover
Extended Insert End Cover
Part #1696 1/8”
1-1/4”
Part #1698
1-1/4”
3/16”
Corner Key
Part #5210
1-1/4”
1-3/16”
Corner Key Part #5210
Insert Divider Tab shelf Extruded Insert Panel
Part #1290 Double Face, post & panel, non-hingeable applications
Custom depth, hingeable, single or double face applications are achieved by attaching the Series 7/12 Retro Body to fabricated or existing sign cabinet frames.
Double face or single face, post & panel or ground mounted, hingeable applications
Series Series Series Series Series
Series 3 Access Body
Access Frame Part #1690
Access Frame Part #1690
Series 3 square ⅜ cap 2SIGNCOMP 5406
Divider corner angle 2SIGNCOMP5300
Custom cutting available Hinge Screw 2SIGNCOMP5170
2T-12-14-75 Teck 12-14x3/4in. Reg Post Cap ⅜ S7 2SIGNCOMP5034
Frame corner angle 2SIGNCOMP 5305
Use Teck #10 x ⅝ 2SIGNCOMP5218
Closure Screw 2SIGNCOMP5180
Cap Screw 2SIGNCOMP5040
EXTRUSIONS
Corner Key 2SIGNCOMP5210
EC-8R
EXCELLART EXTRUSIONS
1 3/32” 8”
1”
1” EC-4,7&8
ITEM- NUMBER 2EC-8R
EC-4,7,8-P
DESCRIPTION
Narrowline Retainer
EC 8R FRAME 26’ MILL FINISH
EC-8R Frame System
ITEM- NUMBER
The EC-8R frame system is 8" in depth and is designed for double face cabinets. EC-8R system was designed for lightweight interior and exterior applications. Unique to the EC-8 system is its 1" radius retainer. This system will hold up to 3/16" material in its built-in retainer system. The removable retainer integrally locks into the EC-8 frame to close the face in on both sides. When closed, it will lock itself into the EC-8 frame showing no exterior fasteners. Corner angles have also been raised off the bottom of the frame to avoid any visible fasteners around the cabinet. Available in mill finish.
2EC4/7/8-NARROWLINE
EC 4,7,8 RETAINER 20’ 6IN. MILL
2EC4/7/8-P
EC 4,7,8 RETAINER 20’ 6”. BRONZE
EC-4,N
3 7/16” 1 1/16” ITEM- NUMBER
EC-8
DESCRIPTION
DESCRIPTION
2EC4N
EC 4N NARROW LINE 26’ MILL FIN
2EC7-P
EC 7 FRAME 20’ 6” BRONZE
2EC7R-P
EC 7R FRAME 20’ 6” BRONZE
7⅛” 1”
EC-4,RN
EC-8 Frame System The EC-8 Frame system is designed for double face applications. Like the EC-4 & 7 frame systems they all use the "snap" retainer system. This frame system can be used for enter and exit signs or directory signs.
ITEM- NUMBER 2EC-8
DESCRIPTION EC 8 FRAME 26’ MILL FINISH
3 7/8” 1” ITEM- NUMBER 2EC4RN
DESCRIPTION EC 4RN NARROW LINE 26’ MILL FIN
EC-6
1½” 1⅜”
ITEM- NUMBER 2EC-6
6½” ITEM- NUMBER
5⅝”
2EC-6R
DESCRIPTION
EC 6 FRAME 26’ MILL FINISH
DESCRIPTION EC 6R FRAME 26’ MILL FINISH
EXCELLART EXTRUSIONS
EC-6R
EC-6R Frame System
EC-6 Frame System This is a versatile family of sign frame extrusions suitable for most single face applications and some double face situations when using pan formed faces. When constructing a simple, economical, single face sign, the EC-6R frame is an ideal choice since its one-piece design dramatically reduces fabrication time. Of course you will still have a removable retainer on one end to facilitate sliding the face out of the way for service access to the interior of the cabinet. For those times when you require a slightly deeper cabinet, just select the desired EC retainer, including our Flex System, and attach to the EC-6 frame body. With this construction, depths of up to 9" can be obtained. Available in both mill finish and pre-painted dark bronze.
The EC-6 frame system is one of many versatile sign frame extrusions suitable for most single face applications and some double face situations when using pan formed faces. When constructing a simple, economical single face sign the EC-6R frame is an ideal choice based on its one-piece design dramatically reduces fabrication time. This system will have removable retainers on one end to facilitate sliding the face out of the way for service access to the interior of the cabinet. For those times when you require a slightly deeper cabinet just select the desired EC retainer system. With the EC-6 frame many depths can be obtained based on the retainer desired. The EC-6 Frame System is available in both mill and pre-painted dark bronze finishes.
EC-12P
EC-12 Standard Frame System 12” 1⅝”
ITEM- NUMBER 2EC12-P
DESCRIPTION
EC12 STANDARD 20’6” BRONZE.
The widest frame in the EC family, the EC-12 frame can be used for monument signs, pole signs with larger diameter poles or whenever a deeper cabinet is desired. This frame has a design similar to the popular EC-6 and EC-9 frames and boasts a strong 8" corner angle. When using the EC-12 as the main frame body and your choice of any retainer in the EC line you can achieve depths from 12 3/4" with the LF retainer to 20" with the EC Flex System. The EC-12 frame is available in both mill and pre-painted dark bronze finishes.
EXCELLART EXTRUSIONS
EC-12
7 13/16” 7 3/16”
12”
7”
1⅝”
ITEM- NUMBER 2EC12-HINGED-P
DESCRIPTION
Ec 12 Hinged Frame 20’6” Bron. 7¼”
EC-12 Hinged Frame System Our widest double face frame extrusion for use when hinged access to the light fixtures is desired, monument signs, pole signs with large diameter poles or whenever a deeper cabinet is required. The integral hinge combines a clean appearance with a functional drainage channel. Another design feature is the ability to add a second retainer to the frame. This retainer holds the inside face in place for your readerboard while using the integral retainer system as your vandal cover. When assembled, a reveal is only shown on top of the cabinet, the side and bottom retainers close neatly into place creating a flush cabinet. Cabinet depths from 13 1/4" to 19 ¾" can be achieved depending on the retainer selected. The EC-12 frame is available in both mill finish and pre-painted dark bronze finishes.
ITEM- NUMBER
DESCRIPTION
2EC-CHANLETTRACEWAY
Ec Chan. Lett. Raceway Set
EC-Channel Letter Raceway Consists of: EC-CLR Back - Part #14010-01 EC-CLR Front - Part #14010-02 EC-CLR Lid - Part #14010-03 This is a three (3)-component raceway that will accommodate all the GFI transformers being manufactured to meet UL 2161 requirements. Back and Front extrusions "snap" together to form a 7 1/4" x 7 13/16" raceway. The Front panel can be drilled or routed prior to assembly. A hinged lid is used for easy access. Available in 20'0" stock lengths or cut to size. End caps, braces and baffles are also available.
1⅛” 1 7/16” 1½” 1½” 5/16” 5/16”
ITEM- NUMBER
2F/HINGEDRETAINER-P
DESCRIPTION F Hinged Retainer 20’6” Bronz
ITEM- NUMBER 2F/STANDARD
DESCRIPTION F Standard Retainer 26’ Mill
1½”
ITEM- NUMBER
DESCRIPTION
2EC-LF/RETAINER
Ec Lf Retainer 20’6” Mill Fin.
2EC/LF-RETAINER/1X5
Eclf Retainer 1”x ⅝ X 12’
ITEM- NUMBER
1½”
1¼”
ITEM- NUMBER
2EC-IDS/24X73
DESCRIPTION 24x73 Ids System W/retainer
Standard Frame With Bleed Cover
DESCRIPTION
2RROD2076012
Rond Rod ½” X 12’
2PS4037537510
Pipe Sch 40 ⅜8” Nps 20’.
2PS40387537512
Pipe Sch 40 ⅜” Nps 12’
2CSS-13-1-20
Css-13-1 X 20’ Mill Finished
2CSS-14-1-20
Css-14-1 X 20’ Mill Finished
2CSS-15-26-1”
Css-15 X 26’1” 6063 T-5 Alumi.
2CSS-16-26’1”
Css-16 X 26’1” 6063 T-5 Alumi.
2CSS-12-3-20
Css-12-3 X 20’ B-lite Gold
2CSS-11-1-20
Css-11-1 X 20’ Mill Finished
2CSS-11-3-20
Css-11-3 X 20’ B-lite Gold
2CSS-11-4-20
Css-11-4 X 20’ B-lite Chrome
2CSS-10-3-20
Css-10-3 X 20’ B-lite Gold
Teak
EC-Flex Clip
Signcom P 5040
Signcomp 5170
Signcom PS 180
EXCELLART EXTRUSIONS
1¼”