Unparalleled Traction on Slippery Surfaces Such as Steps & Wet Floors
AbraCor Non-Skid ®
VOC-Free Composite
COATING • Un-paralled traction on slippery surfaces • No special tools required • Will cure at room temperature
DESCRIPTION:
APPLICATIONS:
AbraCor Non-Skid is a high performance three-part system consisting of a hardener, resin and coarse grit. It is designed to provide unparalleled traction on slippery surfaces such as steps and wet floors. It is suitable for use on clean, sound concrete surfaces and properly prepared steel surfaces.
Flooring Areas and Steps located around …..
When mixed, the resin and hardener react and cure to form a tough, adherent and wear resistant coating. The subsequently applied coarse grit provides the non-skid property. Careful control of the viscosity of the resin-hardener mix insures ease of application using a short-to medium nap roller.
TECHNICAL DATA:
In service, AbraCor Non-Skid provides an effective traction enhancing system that can be used in high traffic areas. Each kit consists of 6 pounds of resin, 3 pounds of hardener and 20 pounds of grit, enough to cover approximately 15 square feet.
APPLICATION PROCEDURE:
• Pumps • Valves • Loading Docks
• Hockey/Sports Arenas • Chemical Mixing Areas • Holding Tanks
PHYSICAL PROPERTY Tensile bond: Shrinkage: Specific Gravity: Max. Operating Temp.:
VALUE 3,000 psi (steel) < 1/2” % 86.46 lb/ft 3 180°-200°F (approx. 82°- 93°C)
ASTM TEST C 633 C 881 D 792
PROCESS PARAMETERS:
1) Surface preparation is critical to success. Concrete surfaces must be clean and sound. Remove grease and oil using a suitable industrial detergent or degreasing compound. Remove scale, chipped or weak concrete. Etching may be used if followed by flushing with clean water. On steel surfaces roughening to a white metal finish by grit blasting is optimal. Remove all grease and oil using a film-free solvent or suitable detergent. In all cases apply AbraCor Non-Skid to a dry surface.
Color, mixed:
Dark gray
Mixing ratio by weight:
2 resin : 1 hardener
Pot life at 75°F: (approx. 24°C)
45 minutes
Gel time:
75 minutes
100% cure:
7 days
2) Mix AbraCor Non-Skid using 2-parts resin to 1-part hardener. Mechanically-assisted mixing for 2-3 minutes to achieve a uniform gray color. Pour within 10 minutes to prevent excessive heat build-up and spread using a short or medium nap roller.
Cure time:
7-8 hrs at 75°F (24°C)
Coverage:
1.61 ft2@ per lb @ 0.030” film thickeness
Viscosity:
Roller applied
3) Sprinkle 2-3 pounds of grit per square foot. Sweep or vacuum away any loose grit after the AbraCor has become tacky to the touch.
COVERAGE & PART NUMBER: 29 lb Kit:
AbraCor Non-Skid has been formulated to allow application in-situ, with no special tools and without the need for additional heat. Coatings can be used on both new and worn areas. Properly mixed and applied coatings will cure at room temperature with minimal shrinkage.
14.5 ft2 @0.030” thick 8617801
Note: Coverage is approximately 1.61 ft 2 per pound of resin and hardener. Do not include the weight of the grit in coverage calculations
YOUR RESOURCE FOR PROTECTION, REPAIR AND JOINING SOLUTIONS Eutectic Corporation N94 W14355 Garwin Mace Drive Menomonee Falls, WI 53051 USA P 800-558-8524 • F 262-255-5542 www.eutecticusa.com
Eutectic Canada 428, rue Aime Vincent Vaudreuil-Dorion, Quebec J7V 5V5 Phone: (800) 361-9439 Fax: (514) 695-8793 www.eutectic-na.com
Eutectic Mexico KM 36.5 Autopista Mexico-Quertaro 54730 Cautitlan-Izcalli Estado de Mexico, Mexico Phone: 011 (52) 55-5872-1111 e-mail: eutectic.mexico@eutectic.com.mx
Statement of Liability: Due to variations inherent in specific applications, the technical information contained herein, including any information as to suggested product applications or results, is presented without representation or warranty, expressed or implied. Without limitation, there are no warranties of merchantability or of fitness for a particular purpose. Each process and application must be fully evaluated by the user in all respects, including suitability, compliance with applicable law and non-infringement of the rights of others, and Eutectic Corporation and its affiliates shall have no liability in respect thereof. ABNS 10-09© 2008, Eutectic Corporation, ® Reg. T.M., Printed in the U.S.A.