All Position, Carbon Steel Electrode ®
BeautyWeld II
WELDING • High quality deposits with minimal spatter • Very Welder-friendly • Smooth Slag release for fast and easy clean-up • Excellent re-strike characteristics increase productivity and efficiency
DESCRIPTION:
WELDING PARAMETERS:
Beautyweld II is a low-carbon electrode for general maintenance and repair with excellent performance and results. High quality, smooth profiled beads are easily attained with minimal spatter and thus clean-up. Fast cleaning, reliable properties and excellent re-strike characteristics make Beautyweld a popular and easy choice for spot and intermittent welding or any other carbon, plain and low-alloy steel applications.
Preparation: Clean weld area. Remove all damaged and fatigued metal, cracks and sharp corners. (Xuper Exotrode® is recommended). Technique: When joining, bevel heavy sections. Preheat is unnecessary unless heavy sections or crack-sensitive base metals are involved. Use AC/DCEP (+) with “A” range for highest deposition rate. Maintain medium arc. Tilt electrode in direction of travel. Weaving should be limited to 1 1/2“x the electrode diameter. Back whip and fill craters.
TYPICAL APPLICATIONS: BUILD-UP OR CLADDING APPLICATIONS: Augers, Impactors, Buckets, Pump Casings, Bucket Teeth, Scraper Blades, Crusher Rollers & Jaws, Sprockets, Gear Teeth, Trencher Teeth, Hammers, Undercarriage Components
DO NOT HEAT 14% MANGANESE STEEL OVER 400°F.
HEALTH AND SAFETY: GENERAL APPLICATIONS: Bucket Lips & Sides, Manganese Filler bars, Conveyor Buckets, Ripper Shanks, Dozer Cutting Edges, Screw Conveyor Flights, Loader Scoops, Wheel Flanges
TECHNICAL DATA: Current: AC/DCEP (+) Typical Tensile Strength: 80,000 psi (552MPa) Typical Yield Strength: 68,000 psi (469 MPa) Elongation: approx. 24% Typical Hardness: Rb 95 as deposited Rc 30 work hardened
PARAMETERS
Observe normal welding practices, respiratory protection and proper air flow pattern advised. For general welding practices, see AWS publications Z49.1 “Safety in Welding and Cutting and Allied Process”. Welding is a completely safe process when performed in accordance with proper safety measures. Become familiar with local safety regulations before beginning welding operations. DO NOT operate welding equipment or use welding materials before you have thoroughly read the proper instruction manual(s). Please refer to the Eutectic internet site for Material Safety Data Sheet (MSDS) information. DISREGARDING THESE INSTRUCTIONS, AND/OR THE INSTRUCTIONS OF WELDING EQUIPMENT OR MATERIAL MANUALS, MAY BE HAZARDOUS TO YOUR HEALTH.
A Range Thick sections, heavy build-up (multi-pass) Diameters: 1/8 5/32 Amperage: 140-180 180-250 B Range Moderate sections Diameters: 1/8 5/32 Amperage: 90-130 120-160
YOUR RESOURCE FOR PROTECTION, REPAIR AND JOINING SOLUTIONS Eutectic Corporation N94 W14355 Garwin Mace Drive Menomonee Falls, WI 53051 USA P 800-558-8524 • F 262-255-5542 www.eutectic.com
Eutectic Canada 428, rue Aime Vincent Vaudreuil-Dorion, Quebec J7V 5V5 Phone: (800) 361-9439 Fax: (514) 695-8793 www.eutectic-na.com
Eutectic Mexico KM 36.5 Autopista Mexico-Quertaro 54730 Cautitlan-Izcalli Estado de Mexico, Mexico Phone: 011 (52) 55-5872-1111 e-mail: eutectic@eutectic.com.mx
Statement of Liability: Due to variations inherent in specific applications, the technical information contained herein, including any information as to suggested product applications or results, is presented without representation or warranty, expressed or implied. Without limitation, there are no warranties of merchantability or of fitness for a particular purpose. Each process and application must be fully evaluated by the user in all respects, including suitability, compliance with applicable law and non-infringement of the rights of others, and Eutectic Corporation and its affiliates shall have no liability in respect thereof. BW2 01-18-13© 2008, Eutectic Corporation, ® Reg. T.M., Printed in the U.S.A.