Ut testing section 4 calibration methods

Page 1

Section 4: Calibration Methods


Content: Section 4: Calibration Methods 4.1: Calibration Methods 4.2: The Calibrations 4.2.1: Distance Amplitude Correction (DAC) 4.2.2: Finding the probe index 4.2.3: Checking the probe angle 4.2.4: Calibration of shear waves for range V1 Block 4.2.5: Dead Zone 4.2.7: Transfer Correction 4.2.8: Linearity Checks (Time Base/ Equipment Gain/ Vertical Gain) 4.2.9: TCG-Time Correction Gain 4.3: Curvature Correction 4.4: Calibration References & Standards 4.5: Questions & Answers 4.6: Video Time


4.1: Calibration Methods Calibration refers to the act of evaluating and adjusting the precision and accuracy of measurement equipment. In ultrasonic testing, several forms of calibration must occur. First, the electronics of the equipment must be calibrated to ensure that they are performing as designed. This operation is usually performed by the equipment manufacturer and will not be discussed further in this material. It is also usually necessary for the operator to perform a "user calibration" of the equipment. This user calibration is necessary because most ultrasonic equipment can be reconfigured for use in a large variety of applications. The user must "calibrate" the system, which includes the equipment settings, the transducer, and the test setup, to validate that the desired level of (1) precision and (2) accuracy are achieved. The term calibration standard is usually only used when an absolute value is measured and in many cases, the standards are traceable back to standards at the National Institute for Standards and Technology.


Calibrations


In ultrasonic testing, there is also a need for reference standards. Reference standards are used to establish a general level of consistency in measurements and to help interpret and quantify the information contained in the received signal. Reference standards are used to validate that the equipment and the setup provide similar results from one day to the next and that similar results are produced by different systems. Reference standards also help the inspector to estimate the size of flaws. In a pulse-echo type setup, signal strength depends on both the size of the flaw and the distance between the flaw and the transducer. The inspector can use a reference standard with an artificially induced flaw of known size and at approximately the same distance away for the transducer to produce a signal. By comparing the signal from the reference standard to that received from the actual flaw, the inspector can estimate the flaw size.


This section will discuss some of the more common calibration and reference specimen that are used in ultrasonic inspection. Some of these specimens are shown in the figure above. Be aware that there are other standards available and that specially designed standards may be required for many applications. The information provided here is intended to serve a general introduction to the standards and not to be instruction on the proper use of the standards.


Introduction to the Common Standards Calibration and reference standards for ultrasonic testing come in many shapes and sizes. The type of standard used is dependent on the NDE application and the form and shape of the object being evaluated. The material of the reference standard should be the same as the material being inspected and the artificially induced flaw should closely resemble that of the actual flaw. This second requirement is a major limitation of most standard reference samples. Most use drilled holes and notches that do not closely represent real flaws. In most cases the artificially induced defects in reference standards are better reflectors of sound energy (due to their flatter and smoother surfaces) and produce indications that are larger than those that a similar sized flaw would produce. Producing more "realistic" defects is cost prohibitive in most cases and, therefore, the inspector can only make an estimate of the flaw size. Computer programs that allow the inspector to create computer simulated models of the part and flaw may one day lessen this limitation.


The IIW Type Calibration Block


The IIW Type Calibration Block


The IIW Type 2 Calibration Block


The IIW Type I Calibration Block


EN12223:1999 Calibration Block


The IIW Phase Array Calibration Block


The IIW Calibration Block 1st Check Index / Check Range


The IIW Calibration Block 2nd Check Angle


The IIW Calibration Block 2nd Check Angle




Find probe angle

Find Index/Range/Resolution


The IIW Phase Array Calibration Block 3rd Check Resolution


V2 Calibration Block


The IIW 2 Calibration Block Check focal point Check probe angle Check range Can not Check resolution


Calibration Blocks


Calibration Blocks- Area Amplitude Block


The standard shown in the above figure is commonly known in the US as an IIW type reference block. IIW is an acronym for the International Institute of Welding. It is referred to as an IIW "type" reference block because it was patterned after the "true" IIW block but does not conform to IIW requirements in IIS/IIW-23-59. "True" IIW blocks are only made out of steel (to be precise, killed, open hearth or electric furnace, low-carbon steel in the normalized condition with a grain size of McQuaid-Ehn #8) where IIW "type" blocks can be commercially obtained in a selection of materials. The dimensions of "true" IIW blocks are in metric units while IIW "type" blocks usually have English units. IIW "type" blocks may also include additional calibration and references features such as notches, circular groves, and scales that are not specified by IIW. There are two full-sized and a mini versions of the IIW type blocks. The Mini version is about one-half the size of the full-sized block and weighs only about one-fourth as much. The IIW type US-1 block was derived the basic "true" IIW block and is shown below in the figure on the left. The IIW type US2 block was developed for US Air Force application and is shown below in the center. The Mini version is shown on the right.


IIW Blocks- US-1

IIW Type US-1


IIW Blocks- IIW Type US-2


IIW Blocks- IIW Type Mini


V1/5, A2 Block


IIW type blocks are used to calibrate instruments for both angle beam and normal incident inspections. Some of their uses include setting metal-distance and sensitivity settings, determining the sound exit point and refracted angle of angle beam transducers, and evaluating depth resolution of normal beam inspection setups. Instructions on using the IIW type blocks can be found in the annex of American Society for Testing and Materials Standard E164, Standard Practice for Ultrasonic Contact Examination of Weldments.

The Miniature Angle-Beam or ROMPAS Calibration Block


DSC Block, Mini block, Rompas Block are all mini blocks.

ROMPAS Calibration Block

AWS Shear Wave Distance/Sensitivity Calibration (DSC) Block


A block that closely resembles the miniature angle-beam block and is used in a similar way is the DSC AWS Block. This block is used to determine the beam exit point and refracted angle of angle-beam transducers and to calibrate distance and set the sensitivity for both normal and angle beam inspection setups. Instructions on using the DSC block can be found in the annex of American Society for Testing and Materials Standard E164, Standard Practice for Ultrasonic Contact Examination of Weldments.


A block that closely resembles the miniature angle-beam block and is used in a similar way is the DSC AWS Block. This block is used to determine the beam exit point and refracted angle of angle-beam transducers and to calibrate distance and set the sensitivity for both normal and angle beam inspection setups. Instructions on using the DSC block can be found in the annex of American Society for Testing and Materials Standard E164, Standard Practice for Ultrasonic Contact Examination of Weldments.


DSC AWS Block


Calibration Range Using DSC AWS Block

www.youtube.com/embed/TEQ8Qrz4D-A


AWS Shear Wave Distance Calibration (DC) Block


AWS Shear Wave Distance Calibration (DC) Block


The DC AWS Block is a metal path distance and beam exit point calibration standard that conforms to the requirements of the American Welding Society (AWS) and the American Association of State Highway and Transportation Officials (AASHTO). Instructions on using the DC block can be found in the annex of American Society for Testing and Materials Standard E164, Standard Practice for Ultrasonic Contact Examination of Weldments.


AWS Resolution Calibration (RC) Block The RC Block is used to determine the resolution of angle beam transducers per the requirements of AWS and AASHTO. Engraved Index markers are provided for 45, 60, and 70 degree refracted angle beams.


The RC Block is used to determine the resolution of angle beam transducers per the requirements of AWS and AASHTO. Engraved Index markers are provided for 45, 60, and 70 degree refracted angle beams.


30 FBH Resolution Reference Block The 30 FBH resolution reference block is used to evaluate the near-surface resolution and flaw size/depth sensitivity of a normal-beam setup. The block contains number 3 (3/64"), 5 (5/64"), and 8 (8/64") ASTM flat bottom holes at ten metal-distances ranging from 0.050 inch (1.27 mm) to 1.250 inch (31.75 mm).


Miniature Resolution Block The miniature resolution block is used to evaluate the near-surface resolution and sensitivity of a normal-beam setup It can be used to calibrate highresolution thickness gages over the range of 0.015 inches (0.381 mm) to 0.125 inches (3.175 mm).


Step and Tapered Calibration Wedges Step and tapered calibration wedges come in a large variety of sizes and configurations. Step wedges are typically manufactured with four or five steps but custom wedge can be obtained with any number of steps. Tapered wedges have a constant taper over the desired thickness range.


Distance/Sensitivity (DS) Block The DS test block is a calibration standard used to check the horizontal linearity and the dB accuracy per requirements of AWS and AASHTO.


Area Amplitude Blocks provide standards for discontinuities of different size at the same depth Distance Amplitude Blocks provide standards for discontinuities of same size at the different depth


The ASTM basic set of Area/Distance Amplitude Blocks consists of ten, two inches diameter blocks


The ASTM basic set of Area/Distance Amplitude Blocks consisits of ten, two inches diameter blocks


Distance/Area-Amplitude Blocks Distance/area amplitude correction blocks typically are purchased as a tenblock set, as shown above. Aluminum sets are manufactured per the requirements of ASTM E127 and steel sets per ASTM E428. Sets can also be purchased in titanium. Each block contains a single flat-bottomed, plugged hole. The hole sizes and metal path distances are as follows: • 3/64" at 3" • 5/64" at 1/8", 1/4", 1/2", 3/4", 11/2", 3", and 6" • 8/64" at 3" and 6" Sets are commonly sold in 4340 Vacuum melt Steel, 7075-T6 Aluminum, and Type 304 Corrosion Resistant Steel. Aluminum blocks are fabricated per the requirements of ASTM E127, Standard Practice for Fabricating and Checking Aluminum Alloy Ultrasonic Standard Reference Blocks. Steel blocks are fabricated per the requirements of ASTM E428, Standard Practice for Fabrication and Control of Steel Reference Blocks Used in Ultrasonic Inspection.


ASTM E 127


Area-Amplitude Blocks Area-amplitude blocks are also usually purchased in an eight-block set and look very similar to Distance/Area-Amplitude Blocks. However, areaamplitude blocks have a constant 3-inch metal path distance and the hole sizes are varied from 1/64" to 8/64" in 1/64" steps. The blocks are used to determine the relationship between flaw size and signal amplitude by comparing signal responses for the different sized holes. Sets are commonly sold in 4340 Vacuum melt Steel, 7075-T6 Aluminum, and Type 304 Corrosion Resistant Steel. Aluminum blocks are fabricated per the requirements of ASTM E127, Standard Practice for Fabricating and Checking Aluminum Alloy Ultrasonic Standard Reference Blocks. Steel blocks are fabricated per the requirements of ASTM E428, Standard Practice for Fabrication and Control of Steel Reference Blocks Used in Ultrasonic Inspection.


Distance-Amplitude #3, #5, #8 FBH Blocks Distance-amplitude blocks also very similar to the distance/area-amplitude blocks pictured above. Nineteen block sets with flat-bottom holes of a single size and varying metal path distances are also commercially available. Sets have either a #3 (3/64") FBH, a #5 (5/64") FBH, or a #8 (8/64") FBH. The metal path distances are 1/16", 1/8", 1/4", 3/8", 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-3/4", 2-1/4", 2-3/4", 3-14", 3-3/4", 4-1/4", 4-3/4", 5-1/4", and 5-3/4". The relationship between the metal path distance and the signal amplitude is determined by comparing signals from same size flaws at different depth. Sets are commonly sold in 4340 Vacuum melt Steel, 7075-T6 Aluminum, and Type 304 Corrosion Resistant Steel. Aluminum blocks are fabricated per the requirements of ASTM E127, Standard Practice for Fabricating and Checking Aluminum Alloy Ultrasonic Standard Reference Blocks. Steel blocks are fabricated per the requirements of ASTM E428, Standard Practice for Fabrication and Control of Steel Reference Blocks Used in Ultrasonic Inspection.


Key Words: Distance Amplitude Blocks DSC DC SC AWS RC

Distance sensitivity calibration Distance calibration Sensitivity calibration AWS Resolution Calibration.


Q56: On the area-amplitude ultrasonic standard test blocks, the flat-bottomed holes in the blocks are: A. All of the same diameter B. Different in diameter, increasing by 1/64 inch increments from the No. 1 block to the No. 8 block C. Largest in the No. 1 block and smallest in the No. 8 block D. Drilled to different depths from the front surface of the test block


Q: A primary purpose of a reference standard is: A. To provide a guide for adjusting instrument controls to reveal discontinuities that are considered harmful to the end use of the product. B. To give the technician a tool for determining exact discontinuity size C. To provide assurance that all discontinuities smaller than a certain specified reference reflector are capable of being directed by the test. D. To provide a standard reflector which exactly simulates natural discontinuities of a critical size.


4.2: The Calibrations 4.2.1: Distance Amplitude Correction (DAC) Distance Amplitude Correction (DAC): Acoustic signals from the same reflecting surface will have different amplitudes at different distances from the transducer. Distance amplitude correction (DAC) provides a means of establishing a graphic ‘reference level sensitivity’ as a function of sweep distance on the A-scan display. The use of DAC allows signals reflected from similar discontinuities to be evaluated where signal attenuation as a function of depth has been correlated. Most often DAC will allow for loss in amplitude over material depth (time), graphically on the A-scan display but can also be done electronically by certain instruments. Because near field length and beam spread vary according to transducer size and frequency, and materials vary in attenuation and velocity, a DAC curve must be established for each different situation. DAC may be employed in both longitudinal and shear modes of operation as well as either contact or immersion inspection techniques.


DAC Curve


http://www.huatecgroup.com/china-digital_portable_dac_avg_curves_ultrasonic_flaw_detector_ut_flaw_detector_fd350-632512.html


DAC- Distance Amplitude Correction


DAC- Distance Amplitude Correction DGS- Distance Gain Size



A distance amplitude correction curve is constructed from the peak amplitude responses from reflectors of equal area at different distances in the same material. A-scan echoes are displayed at their non-electronically compensated height and the peak amplitude of each signal is marked on the flaw detector screen or, preferably, on a transparent plastic sheet attached to the screen. Reference standards which incorporate side drilled holes (SDH), flat bottom holes (FBH), or notches whereby the reflectors are located at varying depths are commonly used. It is important to recognize that regardless of the type of reflector used, the size and shape of the reflector must be constant. Commercially available reference standards for constructing DAC include ASTM Distance/Area Amplitude and ASTM E1158 Distance Amplitude blocks, NAVSHIPS Test block, and ASME Basic Calibration Blocks.


The following applet shows a test block with a side drilled hole. The transducer was chosen so that the signal in the shortest pulse-echo path is in the far-field. The transducer may be moved finding signals at depth ratios of 1, 3, 5, and 7. Red points are "drawn" at the peaks of the signals and are used to form the distance amplitude correction curve drawn in blue. Start by pressing the green "Test now!" button. After determining the amplitudes for various path lengths (4), press "Draw DAC" and then press the green "Test now!" button.


DAC Java

http://www.ndt-ed.org/EducationResources/CommunityCollege/Ultrasonics/CalibrationMeth/applet2/applet2.htm


Developing a Distance Amplitude Correction (DAC) Curve Distance Amplitude Correction (DAC) provides a means of establishing a graphic ‘reference level sensitivity’ as a function of sweep distance on the Ascan display. The use of DAC allows signals reflected from similar discontinuities to be evaluated where signal attenuation as a function of depth may be correlated. In establishing the DAC curve, all A-scan echoes are displayed at their non-electronically compensated height. Construction of a DAC involves the use of reference standards which incorporate side drilled holes (SDH), flat bottom holes (FBH), or notches whereby the reflectors are located at varying depths. It is important to recognize regardless of the type of reflector that is used in constructing the DAC, the size and shape of the reflector must be constant over the sound path distance. Commercially available reference standards for constructing DAC include ASTM Distance/Area Amplitude and ASTM E1158 Distance Amplitude blocks, NAVSHIPS Test block, and ASME Basic Calibration Blocks.


Sequence for constructing a DAC curve when performing a straight beam contact inspection on 1 ¾” thick material. 1.) Using a suitable reference standard, calibrate the sweep for a distance appropriate for the material to be inspected, i.e.. using a 1” thick standard, calibrate the sweep for 2” of material travel.


Back Wall Echo


Back Wall Echo

Sweep 2” / Distance 1”


2.) This example represents the use a 1 3/4” thick reference standard with 1/8” side drilled holes located at 1/4 T and 3/4 T respectively. ‘T’ being equal to the block thickness.


3.) Position the transducer over the 1/4T hole and peak the signal to approximately 80% FSH (Full screen height), mark the peak of the echo on the display using a suitable marker, and record the gain setting.


4.) With no further adjustments to the gain control, position the transducer over the 3/4T hole and peak the signal, mark the peak of the echo on the display.


5.) To complete the DAC curve connect the dots with a smooth line. The completed curve represents the ‘reference level sensitivity’ for this application.


Plotting DAC Curve


DAC Curve


DAC Curve


Gain Control for FSH: It should be remember that the dB is a means of comparing signals. All UT sets are different and a FSH with a gain controls of 36dB in one UT set and be at FSH at another UT set with a gain control reading of 26dB. The gain controls allow us to set sensitivity and form the basis of Ultrasonic Sizing Techniques.



Birring NDT Series, Ultrasonic Distance Amplitude Correction - DAC

www.youtube.com/embed/qUqaF0PnLGA?list=UUZncq6JFram3pfQDlzGggwA


Alta Vista UT Calibration DAC Curve

www.youtube.com/embed/VNgMKlp43I8


4.2.2: Finding the probe index


Exit Point A2 Block


Exit Point- A5 Block


Q16: Notches are frequently used as a reference reflector for: A. B. C. D.

Distance amplitude calibration for shear wave Area amplitude calibration Thickness calibration for plate Determining the near-surface resolution


5.2.3: Checking the probe angle


Probe Angles- A2 Block


Probe Angles- A5 Block


4.2.4: Calibration of shear waves for range V1 Block


Calibration of shear waves for range V1 Block


1st Echo from circular Section


Echo from 100mm circular Section


Calibration of shear waves for range V1 Block

Test block 1 for calibrating the time base (depth scale) of a flaw detector for vertical probes (longitudinal waves) for angle probes (transverse waves), for determining the probe index and beam angle of angle probes, and for checking the short term consistency of the sensitivity of vertical probes


Calibration of shear waves for range V2 Block


25 mm radius from V2 Block


50 mm radius from V2 Block


100 mm radius from K2 Block


Calibration of shear waves for range V2 Block


Shear Wave Distance Calibration IIW Block & DSC Blocks

www.youtube.com/embed/RmtHmtOozic


Exit Point /Range/Probe Angle calibration using IIW Block (Repeat-Code1)

www.youtube.com/embed/Qr0dGNuq9yY


4.2.5: Dead Zone Determine the dead zone by finding the hole echo which is easily identifiable from the probe noise at the shortest range


Dead Zone

Determine the dead zone by finding the hole echo which is easily identifiable from the probe noise at the shortest range


4.2.6: 20 dB Profile- A5 Block


20 dB Profile Probe Beam Line of Symmetry


20 dB Profile Probe Beam Sound Pressure


4.2.7: Transfer Correction Methods of compensating for transfer and attenuation loss differences for 0attenuation 000compression probes and for shear wave compression probes. These are based on obtaining similar echo responses on both the calibration block and on the component. For 0degree probes backwall echoes are used to probes establish transfer and attenuation correction. For shear wave probes two identical probes are used in “pitch-catch� in order to obtain what are effectively backwall echoes. either method cannot be used if the either component does not have a convenient parallel section.


Example: 0 degree Probe Calibration 40mm thick block – Gain to achieve FSH


Example: 0 degree Probe Calibration 30mm thick block – Gain to achieve FSH


TRANSFER & ATTENUATION CORRECTION: 0 degree Probes

If the results are plotted on log -linear paper they will form straight parallel lines provided that there is no attenuation difference if an attenuation difference occurs then the resultant lines will no longer be parallel.


Transfer and Attenuation Correction: Shear Probe The principle for obtaining transfer correction for shear wave probes is the same as it was for compression probes except that backwall echoes are replaced by pitch --catch responses.


4.2.8: Linearity Checks (Time Base / Equipment Gain / Vertical Gain)


4.2.8.1:

Linearity of time base

General This check may be carried out using a standard calibration block eg A2, and a compressional wave probe. The linearity should be checked over a range at least equal to that which is to be used in subsequent testing. Method a) Place the probe on the 25mm thickness of the A2 block and adjust the controls to display ten BWEs. b) Adjust the controls so that the first and last BWEs coincide with the scale marks at 1 and 10. c) Increase the gain to bring successive backwall echoes to 80% FSH. The leading edge of each echo should line up with the appropriate reticules line. d) Record any deviations at approximately half screen height. Deviations should be expressed as a percentage of the range between the first and last echoes displayed (ie 225mm).


Tolerance Unless otherwise specified by the testing standard, a tolerance of Âą2% is considered acceptable. Frequency of checking This check shall be carried out at least once per week.






Ultrasonic Testing - Horizontal Linearity (Calibration)

www.youtube.com/embed/NuS6j0SmjKQ


4.2.8.2:

Linearity of Equipment Gains

General This is a check on both the linearity of the amplifier within the set and the calibrated gain control. It can be carried out on any calibration block containing a side-drilled hole and should be the probe to be used in subsequent testing. Reject/suppression controls shall be switched off. Method ď Ž Position the probe on a calibration block to obtain a reflected signal from a small reflector eg 1.5mm hole in the A2 block. ď Ž Adjust the gain to set this signal to 80% FSH and note the gain setting (dB). - Increase the gain by 2dB and record the amplitude of the signal. - Remove the 2dB and return the signal to 80% FSH. - Reduce the gain by 6dB and record signal amplitude. - Reduce the gain by a further 12dB (18 intotal) and record signal amplitude. - Reduce the gain by a further 6dB (24 in total) and record signal amplitude.


Tolerance

Frequency of checking The check shall be carried out at least once per week.




5.2.8.3-1: Linearity of vertical display to EN12668-1 Procedure: Test the ultrasonic instrument screen linearity by altering the amplitude of a reference input using an external calibrated attenuator and observing the change in the signal height on the ultrasonic instrument screen. Report the gain setting at the beginning of the test. Check the linearity at prescribed intervals from 0 dB to - 26 dB of full screen height. Repeat the test for centre frequencies for of each filter as measured in 9.5.2. Using the same set-up shown in Figure 6 set the external calibrated attenuator to 2 dB and adjust the input signal and the gain of the ultrasonic instrument so the signal is 80 % of full screen height. Without changing the gain of the ultrasonic instrument switch the external calibrated attenuator to the values given in the Table 4. For each setting measure the amplitude of the signal on the ultrasonic instrument screen. Extract from: BS EN 12668-1:2010 Non-destructive testing- Characterization and verification of ultrasonic examination equipment Part 1: Instruments



Figure 6 — General purpose set-up for equipment


4.2.8.3-2: Linearity of vertical display to ASTM E317-01 Vertical Limit and Linearity: Significance—Vertical limit and linearity have significance when echo signal amplitudes are to be determined from the display screen or corresponding output signals, and are to be used for evaluation of discontinuities or acceptance criteria. A specified minimum trace deflection and linearity limit may be required to achieve the desired amplitude accuracy. For other situations they may not be important, for example, go/no-go examinations with flaw alarms or evaluation by comparison with a reference level using calibrated gain controls. This practice describes both the two-signal ratio technique (Method A) and the input/output attenuator technique (Method B). Extract from: ASTM E317-01 Standard Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Examination Instruments and Systems without the Use of Electronic Measurement Instruments

Note: Method A: two-signal ratio technique collecting 2 signal from the reflectors of same size at different depth.


Method A: 6.3.2.1 Apparatus—A test block is required that produces two non interfering signals having an amplitude ratio of 2 to 1. These are compared over the usable screen height as the instrument gain is changed. The two amplitudes will be referred to as HA and HB (HA > HB). The two signals may occur in either screen order and do not have to be successive if part of a multipleecho pattern. Unless otherwise specified in the requesting document, any test block that will produce such signals at the nominal test settings specified can be used. For many commonly used search units and test conditions, the test block shown in Fig. 1 will usually be satisfactory when the beam is directed along the H dimension toward the two holes. The method is applicable to either contact or immersion tests; however, if a choice exists, the latter may be preferable for ease of set-up and coupling stability……(more…)



4.2.9: Time Correction Gain (TCG) Please read: http://aqualified.com/tcg-dac-ndt-ultrasound/


Q61: The vertical linear range of a test instrument may be determined by obtaining ultrasonic responses from: A. B. C. D.

a set of distance amplitude blocks steel ball located at several different water path distances a set of area amplitude blocks all of the above


Q29: Test sensitivity correction for a metal distance and discontinuity area responses are accomplished by using: A. B. C. D.

An area amplitude set of blocks An area amplitude and a distance amplitude set of blocks A distance amplitude set of blocks Steel balls of varying diameters.


4.3: Curvature Correction Curvature in the surface of a component will have an effect on the shape of the ultrasonic beam. The image to the right shows the beam from a focused immersion probe being projected on to the surface of a component. Lighter colors represent areas of greater beam intensity. It can be seen that concave surfaces work to focus the beam and convex surfaces work to defocus the beam. Similar effects are also seen with contact transducers. When using the amplitude of the ultrasonic signal to size flaws or for another purpose, it is necessary to correct for surface curvature when it is encountered. The "correction" value is the change in amplitude needed to bring signals from a curved surface measurement to the flat surface or DAC value.


Convex surfaces work to defocus the beam

Diverge if the surface is convex.

Concave surface contourFocusing effects


Concave surfaces work to focus the beam

Diverge if the surface is convex.

Concave surface contourFocusing effects


convex surfaces work to defocus the beam Convex surfaces work to defocus the beam


Convex surfaces work to defocus the beam- When sound travels from a liquid through a metal, it will converge if the surface is concave or diverge if the surface is convex.


Q: In an immersion method, the incident sound path enter the specimen interface with convex geometry, the sound path on entry into the specimen, the convex surface works to a) b) c) d)

De-focus the sound Focus the sound Has no effect on the focusing or de-focusing the sound Reflected totally all the incident sound.


Q: In transmitting sound energy into a part shown below in a immersion testing, the sound beam will be: a) b) c) d)

Diverge Converge Straight into Will not enter


A curvature correction curve can be generated experimentally in a manner similar to that used to generate a DAC curve, This simply requires a component with a representative reflector at various distances below the curved surface. Since any change in the radius will change the focus of the sound beam, it may be necessary to develop reference standards with a range of surface curvatures. However, computer modeling can also be used to generate a close approximation of the curvature correction value. Work by Ying and Baudry (ASME 62-WA175, 1962) and by Birchak and Serabian (Mat. Eval. 36(1), 1978) derived methods for determining "correction factors" to account for change in signal amplitude as a function of the radius of curvature of convex, cylindrical components. An alternative model for contact and immersion probe inspection was more recently by researchers at the Center for NDE at Iowa State University. This mathematical model further predicts transducer radiation patterns using the Gauss-Hermite model, which has been used extensively for simulation of immersion mode inspections.


The resulting model allows computationally efficient prediction of the full ultrasonic fields in the component for 1. 2. 3. 4.

any frequency, including broadband measurements. both circular and rectangular crystal shapes. general component surface curvature both normal and oblique incidence (e.g., angle beam wedges) transducers.

When coupled with analytical models for defect scattering amplitudes, the model can be used to predict actual flaw waveforms. The image shown above was generated with this model.


The plot to the right shows an example curvature correction curve and DAC curve. This curvature correction curve was generated for the application of detecting a #4 flat bottom hole under a curved surface as shown in the sketch and photograph. An immersion techniques was used generate a shear wave since the reflective surface of the target flaw was not parallel with the surface. The DAC curve drops monotonically since the water path ensures that the near field of the sound beam is always outside the part. The correction factor starts out negative because of the focusing effect of the curved surface. At greater depths, the correction factor is positive due to the increased beam spread beyond the focal zone caused by the surface curvature.


Curvature Corrections


A table of correction values and the DAC and curvature correction curves for different size radiuses can be found at the following link.

https://www.nde-ed.org/EducationResources/CommunityCollege/Ultrasonics/CalibrationMeth/table/table.htm


Curvature Correction


Curvature Correction


4.4: Calibration References & Standards What are standards? Standards are documented agreements containing technical specifications or other precise criteria to be used consistently as rules, guidelines, or definitions of characteristics, in order to ensure that materials, products, processes, and services are fit for their purpose. For example, the format of the credit cards, phone cards, and "smart" cards that have become commonplace is derived from an ISO International Standard. Adhering to the standard, which defines such features as an optimal thickness (0.76 mm), means that the cards can be used worldwide.


An important source of practice codes, standards, and recommendations for NDT is given in the Annual Book of the American Society of Testing and Materials, ASTM. Volume 03.03, Nondestructive Testing is revised annually, covering acoustic emission, eddy current, leak testing, liquid penetrant, magnetic particle, radiography, thermography, and ultrasonics. There are many efforts on the part of the National Institute of Standards and Technology (NIST) and other standards organizations, both national and international, to work through technical issues and harmonize national and international standards.


Reference Reflectors: are used as a basis for establishing system performance and sensitivity.


Spherical reflectors are often used in immersion techniques for assessing sound fields. 1. Omni direction 2. Sphere directivity patterns reduce reflectance as compare with plane reflector 3. Sphere of any materials could be used, however steel balls are often preferred.


Reference Reflectors are used as a basis for establishing system performance and sensitivity.


4.5: Questions & Answers Exercises


Q80: The 50 mm diameter hole in an IIW block is used to: (a) Determine the beam index point (b) Check resolution (c) Calibrate angle beam distance (d) Check beam angle Q81: The 100 mm radius in an IIW block is used to: (a) Calibrate sensitivity level (b) Check resolution (c) Calibrate angle beam distance (d) Check beam angle


Q6: The Notches are frequently used for reference reflectors for: A. B. C. D.

Distance amplitude calibration for shear wave Area amplitude calibration Thickness calibration of plate Determine of near surface resolution

Q17: Notches provide good reference discontinuities when UT examination is conducted to primarily detect defects such as: A. B. C. D.

Porosity in rolled plate Inadequate penetration at the root of weld Weld porosity Internal inclusion


4.6: Video Time

http://v.pps.tv/play_315ARS.html


Birring NDT Series, UT of Welds Part 1 of 2 - CALIBRATION

https://www.youtube.com/embed/SRJktrHUlM4


Birring NDT Series, Ultrasonic Testing # 4, Angle Beam Shear Wave UT as per AWS D1.1

www.youtube.com/embed/vXcAI-Zci30






Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.