BW1 Cinemax by Cineversum

CineMax Kit ASSEMBLY AND CALIBRATION

www.cineversum.com

Ref: T9003000

Rev: 02

Part. No.: R599766

Changes CineVERSUM provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and ﬁtness for a particular purpose. CineVERSUM may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice. This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication.

Copyright All right reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of CineVERSUM.

Guarantee CineVERSUM provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults. CineVERSUM must be informed immediately in writing of any complaints. If the purchaser or third party caries out modifications or repairs on goods delivered by CineVERSUM, or if the goods are handle incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by CineVERSUM either. The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer.

Trademarks Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brands and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products of their manufactures.

R599766 - 2.35 Cinemax Kit

TABLE OF CONTENTS 1.0

2.35 Cinemax Kit .............................................................................................................. 4 1.1 1.2

1.3

2.0

Projector-side configuration ............................................................................................ 8 2.1

2.2

2.3

2.4

3.0

Installing the Mounting Plate............................................................................................................. 4 Cinemax prismatic Lens alignment ................................................................................................... 5 Adjust the full screen picture .............................................................................................. 5 Set the horizontal picture position into the screen .............................................................. 6 Set the tilt and vertical position of the lens ......................................................................... 7 Install the Lens Cap ........................................................................................................................... 8 Configure the 12V Trigger 2.............................................................................................................. 8 Connect your screen control device to the 12V Trigger 2 output ...................................... 8 Configure Initial Setup Menu -> Trigger 2 to THEATRE .............................................. 8 Configure the Anamorphic Aspect Ratios ......................................................................................... 9 16:9 input: Aspect Ratio to Converted 16:9 .................................................................... 9 Cinemascope input: Aspect Ratio to Cinemascope ......................................................... 9 Using the Remote Control Unit. ...................................................................................................... 10 Select the correct Aspect Ratio for each input .................................................................. 10 [ASPECT] button behavior ............................................................................................... 11 Quick Aspect Ratio change on the same input.................................................................. 11 Using RS-232 protocole................................................................................................................... 11 Communication Specifications ......................................................................................... 11 Command Format.............................................................................................................. 12 Available Lengths and Commands.................................................................................... 12

Miscellaneous .................................................................................................................. 14 3.1 3.2

Dimensions ...................................................................................................................................... 14 Projection distances ......................................................................................................................... 14

R599766 - 2.35 Cinemax Kit

1.0 2.35 CINEMAX KIT

1.0 2.35 CINEMAX KIT The 2.35 Cinemax Kit is a simple and versatile solution to operate a cinemascope experience using the Cinemax prismatic Lens. The Blackwing One features an exclusive THEATRE Mode for an easier screen masking control. The new THEATRE Mode features:

1.1

•

Integrated CIW system.

•

Dedicated menu to program the 12V Trigger2 output to control your motorized screen mask.

•

Direct access button on the Remote Control Unit to switch between Anamorphic modes.

Installing the Mounting Plate a)Use the 3x M6x15 screws to ﬁx the plate at the bottom of the projector.

M6x15 screews

b) Use the 4x M5x7 screws to fix the lens support. to the fixing plate and the 2 round head screws to fix the Cinemax prismatic Lens in front of the projector lens.

M5x7

round head screws

R599766 - 2.35 Cinemax Kit

1.0 2.35 CINEMAX KIT

1.2

Cinemax prismatic Lens alignment Adjust the full screen picture To obtain a 2.35 picture, you can use a 16:9 picture set to Full Screen aspect ratio. The picture must fulďŹ ll the screen. These adjustment are made by using the Zoom and the vertical shift and horizontal shift of the projector. When the picture position is correct, adjust the picture focus.

ZOOM

Adjust the Zoom and the Lens Offset until the picture fulďŹ lls the screen.

R599766 - 2.35 Cinemax Kit

1.0 2.35 CINEMAX KIT

FOCU

Adjust the picture Focus

Set the horizontal picture position into the screen

A A

To adjust the horizontal position of the picture into the screen, release the 4 screws (A) and turn the Anamorphic Lens left or right to obtain a centered 2.35 picture. Tighten the screws when completed. This adjustment can also be achieved by using the Horizontal Lens Offset. The Horizontal Lens Offset should be used only for ďŹ ne adjustments. The use of the maximum 30% horizontal offset may decrease the overall picture quality..

R599766 - 2.35 Cinemax Kit

1.0 2.35 CINEMAX KIT

Set the tilt and vertical position of the lens

Adjust the Anamorphic Lens tilt and vertical position, so that the projector light beam is centered into the Anamorphic Lens and to compensate the upper and lower pincushion effects. Tighten the 2 screws (B) when completed. You may obtain a residual pincushion effect at the screen when using a throw ratio between 1.5:1 and 1.8:1 or a projection distance shorter than 5 meters. It is recommended to install your projector at a minimum distance of 5 meters from the screen and using 1.8:1 or higher throw ratio with a ďŹ&#x201A;at screen. Otherwise, the use of a curved 2.35 screen is recommended.

R599766 - 2.35 Cinemax Kit

2.0 PROJECTOR-SIDE CONFIGURATION

1.3

Install the Lens Cap

C Install the lens Cap and ﬁx it using the 2 screws (C).

2.0 PROJECTOR-SIDE CONFIGURATION 2.1

Conﬁgure the 12V Trigger 2 Connect your screen control device to the 12V Trigger 2 output 12V Trigger 1 12V Trigger 2

Screen mask Control

The 12V Trigger 2 output can control the screen masking

Conﬁgure Initial Setup Menu ⇒ Trigger 2 to “THEATRE” The “Initial Setup ⇒ Trigger 2” menu determines the Trigger 2 output located in the panel input of the Blackwing One this is a global parameter (for all inputs):

•

ON: the 12V Trigger 2 is always active when the projector is switched ON.

•

OFF: the 12V Trigger 2 is always switched Off.

•

THEATRE: this option turns ON the Trigger 2 output when the aspect ratio is set to “Cinemascope”.

R599766 - 2.35 Cinemax Kit

2.0 PROJECTOR-SIDE CONFIGURATION

2.2

Conﬁgure the Anamorphic Aspect Ratios 16:9 input: Aspect Ratio to “Converted 16:9” When you select a 16:9 input, choose the Converted 16:9 aspect ratio, and conﬁgure the Aspect Ratio between 1.30 and 1.40 to obtain the correct geometry. • Select Converted 16:9 in the OSD Menu “Input Signal ⇒ Aspect Ratio ⇒ Converted 16:9” • Then choose the correct Aspect Ratio between 1.30 and 1.40 in the menu ”Input Signal ⇒ Converted 16:9 Aspect Ratio ⇒ 1.33” so that the 16:9 picture is letter-boxed into the 2.35 screen. You can rise the Aspect Ratio up to 1.78 to reduce the black bars on the left and the right of the screen but the picture may be horizontally stretched.

1.33x

1.60x

You can rise the Converted 16:9 Aspect Ratio from 1.30 up to 1.78 to reduce the black bars.

Cinemascope input: Aspect Ratio to “Cinemascope” When selecting a wide format input (2.35:1, 2.37:1 or 2.40:1), the original aspect ratio of the source is larger than 16:9, you can see black bars on the top and the bottom of the screen. • Select the Cinemascope mode for this input in the “Input Signal ⇒ Aspect Ratio ⇒ Cinemascope”. • Then choose the correct Cinemascope Aspect Ratio between 2.30 and 2.50 in the menu ”Input Signal ⇒ Cinemascope Aspect Ratio ⇒ 2.37“ so that the black bars disappear and the active picture fulﬁlls the screen.

2.34x

2.37x

Adjust the Cinemascope Aspect Ratio between 2.30 and 2.50 to eliminate the black bars. You can lower the Cinemascope aspect ratio down to 1.78 if you plan to watch an original 16:9 program with upper and lower picture portion lost. The picture may be horizontally stretched.

R599766 - 2.35 Cinemax Kit

2.0 PROJECTOR-SIDE CONFIGURATION

2.3

Using the Remote Control Unit.

Select active input

Select the correct Aspect Ratio

Blackwing One RCU and quick access features

Select the correct Aspect Ratio for each input On the ﬁrst install, conﬁgure the desired Aspect Ratio for each input. By example, a TV source on HDMI1 will use Converted 16:9 (16:9 native format) and a Blu-Ray player on HDMI2 will use Cinemascope (Cinemascope format). Each input retains the last Aspect Ratio applied, so that selecting a different input with the RCU automatically choose the correct Aspect Ratio.

R599766 - 2.35 Cinemax Kit

2.0 PROJECTOR-SIDE CONFIGURATION

[ASPECT] button behavior The [ASPECT] button triggers the 5 aspect ratio modes. Once a given aspect ratio is validated, the order of the next aspect ratio is reversed so that the previous aspect ratio becomes the next aspect ratio as described below.

Full Screen

Cinemascope

Standard

The Cinemax Kit uses Converted 16:9 and and Cinemascope modes.

Virtual Wide

Converted 16:9

When you press sequentially the [ASPECT] button, the aspect mode rotation goes clock-wise. Press [ESC] or wait 15 seconds until the message fades out to confirm selection. Next time that you will press the [ASPECT] button, the rotation order is reversed. This behavior ensures a fast switch between two particular aspect ratios.

Quick Aspect Ratio change on the same input The Remote Control Unit can be used to quickly switch the aspect ratio by pressing twice the [ASPECT] button to switch forth and backward from Cinemascope to Converted 16:9 as described below: Full Screen on 2.35 screen

Converted 16:9

Cinemascope

16:9 picture

2.35:1 picture

When the source automatically switches format... ... press twice [ASPECT] button on the Remote Control Unit

2.4

Using RS-232 protocole Communication SpeciďŹ cations Control of 2.35 THEATRE Concept is possible using a computer or automation device connected with a RS-232 straight cable connected to the Blackwing One (male - female D-sub 9 pins cable). Communication speciďŹ cations

R599766 - 2.35 Cinemax Kit

2.0 PROJECTOR-SIDE CONFIGURATION for this unit are as follows:

Baud Rate

115200 bps

Data Format

Binary

Character Length

8 bits

Parity

None

Stop Bit

1 bit

X on/off

None

Flow Control

None

Command Format When sending a command to this unit, use the following data format:

Header

Length

Command

EoD

1 or 3 bytes

0 or 1 byte

at least 1 byte

1 byte

Header

(00h) for power ON command, (77h 88h 99h) for other commands.

Length

The total bytes of “Length” and “Command”

Command

Designates the command

EoD

Designates the end of the data. Fixed to (FFh)

Available Lengths and Commands Command Header (00h) Power ON

Length

Command

None

01h

Length

Command

03h

02h 01hh

Switch Input

03h

Blanking

03h

Keypad

03h

12V Trigger #2

03h

02h 02h 02h 03h 02h 04h 02h 05h 02h 06h 02h 07h 02h 08h 02h 09h 01h 01h 01h 02h 01h 03h 01h 04h 01h 05h 01h 06h 01h 07h 01h 08h 01h 09h 03h 01h 03h 02h 03h 03h

Command Header (77h 88h 99h) Power OFF

Description If the projector is in standby mode, this command switch the unit ON. Description If the projector is powered ON, this command switch this unit into Standby Mode. (Directly OFF) Switch active input to Video (Composite) Switch active input to S-Video Switch active input to Component Switch active input to VGA (sD15) Switch active input to HDMI 1 Switch active input to HDMI 2 Toggle projector Blanking ON Toggle projector Blanking OFF MENU: Toggle OSD Menu ON and OFF UP: Uses as up function key for navigation DOWN: Uses as down function key for navigation LEFT: Uses as left function key for navigation RIGHT: Uses as right function key for navigation ENTER: Selects menu item or the next menu EXIT: exits the current menu to the previous one. SOURCE: Switch input source. Power OFF: Turn off the projector (send twice) Switch the trigger to ON. Switch the trigger to OFF Switch the trigger to THEATRE

R599766 - 2.35 Cinemax Kit

2.0 PROJECTOR-SIDE CONFIGURATION Aspect Ratio

03h

Lens Aperture

03h

Picture Mode

03h

Picture Adjust

03h

Colour Temperature

03h

Gamma

03h

Scaling features

03h

Temporal Noise

03h

Mosquito Noise

03h

Block Artifact

03h

Reset to default

03h

03h 04h 03h 05h 03h 06h 03h 07h 03h 08h 03h 09h 03h 0Ah 04h 01h 04h 02h 04h 03h 04h 04h 04h 05h 04h 06h 05h 01h 05h 02h 05h 03h 05h 04h 05h 05h 05h 06h 05h 07h 06h 01h 06h 02h 06h 03h 06h 04h 06h 05h 06h 06h 06h 07h 07h 01h 07h 02h 07h 03h 07h 04h 07h 05h 07h 06h 07h 07h 08h 01h 08h 02h 08h 03h 08h 04h 08h 05h 08h 06h 08h 07h 08h 08h 09h 01h 09h 02h 09h 03h 09h 04h 09h 05h 09h 06h 0Ah 01h

Switch aspect ratio to Standard Switch aspect ratio to Full Screen Switch aspect ratio to Cinemascope Switch aspect ratio to Converted 16:9 Switch aspect ratio to Virtual Wide Open one level up the Lens Aperture Close on level down the Lens Aperture Switch picture mode to Standard Switch picture mode to Dynamic Switch picture mode to Theater Switch picture mode to User 1 Switch picture mode to User 2 Switch picture mode to User 3 Show brightness slider (use left or right to modify) Show contrast slider Show colour slider Show hue slider Show sharpness slider Show black level slider Show white level slider Switch colour temperature to Low Switch colour temperature to medium Switch colour temperature to High Switch colour temperature to User 1 Switch colour temperature to User 2 Switch colour temperature to User 3 Switch colour temperature to Medium-high Switch gamma to Gamma 1 Switch gamma to Gamma 2 Switch gamma to Gamma 3 Switch gamma to Gamma 4 Switch gamma to User 1 Switch gamma to User 2 Switch gamma to User 3 Set detail enhancement to Off Set detail enhancement to Low Set detail enhancement to Medium Set detail enhancement to High Set TNR to Off Set TNR to Low Set TNR to Medium Set TNR to High Set MNR to Off Set MNR to Low Set MNR to Medium Set MNR to High Set BAR to Off Set BAR to On Reset settings to default value

Examples You want to... Command to send Switch the projector ON 00h 01h FFh Switch the projector OFF 77h 88h 99h 03h 02h 01h FFh Switch the projector OFF with OSD conďŹ rmation 77h 88h 99h 03h 01h 09h FFh

R599766 - 2.35 Cinemax Kit

3.0 MISCELLANEOUS Switch Aspcet Ratio mode to Cinemascope Switch Aspcet Ratio mode to Converted 16:9

77h 88h 99h 03h 03h 06h FFh 77h 88h 99h 03h 03h 07h FFh

3.0 MISCELLANEOUS 3.1

Dimensions

199 mm 7.8’’

800mm

3.2

31.5’’

800mm

31.5’’

530 mm

20.9’’

Projection distances Projection Screen Size Diagonal size (Aspect Ratio 2.35:1)

Projection Screen Base size

Projection Screen Height

Blackwing One

107" (2720 mm)

98.4" (2500 mm)

41.7" (1060 mm)

3240 mm - 4640 mm

128" (3250 mm)

118.1" (3000 mm)

50.4" (1280 mm)

3870 mm - 5550 mm

149" (3780 mm)

137.8" (3500 mm)

58.7" (1490 mm)

4510 mm - 6460 mm

170" (4520 mm)

157.5" (4000 mm)

66.9" (1700 mm)

5150 mm - 7370 mm

200" (5080 mm)

184.3" (4680 mm)

77.5" (1970 mm)

6050 mm - 8670 mm

Projecting Distance minimum - maximum

R599766 - 2.35 Cinemax Kit

Contact Information: TEC - CineVERSUM 7, rue La CAILLE, 75017 Paris - FRANCE Web: www.cineversum.com

Contact information

TEC - CineVERSUM 7, rue La Caille, 75017 Paris, France www.cineversum.com Part. No. R599766