Model 72600 Long arm, Single needle, High speed, Extra heavy duty, Top and bottom feed lockstitch sewing machine with extra large capacity hook and bobbin for heavy weight materials & thick sewing threads
Instructions Manual & Illustrated Parts Catalogue
This catalog has been prepared to guide you while operating 72600 heavy duty industrial sewing machine and arranged to simplify ordering spare parts. Before putting the machines described in this manual into service, carefully read the instructions. The starting of each machine is only permitted after taking notice of the instructions and by qualified operators.
Edition No.: English 2.0 Rights Reserved In All Countries Printed in China
TABLE OF CONTENTS
INSTRUCTIONS OF MACHINE BEFORE USING INSTALLING THE MOTOR CONNECTING THE CLUTH LEVER TO THE PEDAL OILING TRIAL RUN INSTALLING THE NEEDLE
Page
2 2 2 2 3 3 3
COORDINATION AMONG THE NEEDLE, THE THREAD AND THE MATERIAL THREADING THE NEEDLE THREAD BOBBIN WINDER ADJUSTMENT ADJUSTING THE STITCH LENGTH ADJUSTING THE PRESSURE OF PRESSER FOOT ADJUST THE THREAD TENSION TIMING BETWEEN THE NEEDLE AND THE ROTATING HOOK REMOVING AND INSTALLING THE ROTATING HOOK INSTALING THE ROTATING HOOK POSITION LIMIT SOCKET INSTALLING FEED DOG TIMING BETWEEN THE NEEDLE AND FEED-DOG ADJUSTING PRESSER BAR CROSS LIFTING MECHANISMS ADJUSTING TOTAL LIFTING HEIGHT OF ALTERNATING AND SMALL PRESSER FOOT CLEAN THE MACHINE REGULARY PARTS MANUAL CASTING HOUSING NEEDLE BAR AND UPPER SHAFT UPPER FEED MECHANISM BOTTOM SHAFT FEED REGULATING MECHANISM FEED MECHANISM PRESSER FOOT LIFTER (1/3) PRESSER FOOT LIFTER (2/3) PRESSER FOOT LIFTER (3/3) OIL PARTS ACCESSORIES
-1-
3 4 4 4 5 5 5 6 6 7 7 8 8 8 10 11-12 13-15 16-18 19-20 21-22 23-25 26-27 28-30 31-32 33-34 35-36
INSTRUCTIONS OF MACHINE #72600 heavy duty sewing machine is designed for seaming heavy weight fabric such as tent, canvas, upholstery, leather with upper and lower feed and large rotary hook, the free-formed stitching function make this model specially suitable for stitching the FIBC bags. Seam specification: 301 lockstitch Stitch range: 0-12.7 mm Needle: DDĂ—1 25# Needle bar stroke: 50.8mm Presser foot lift by hand: 12.7mm Presser foot lift by pneumatic: 18mm Rotary hook: KRT132 Working clearance: 400mmĂ—180mm Lubrication: manual Maximum speed: up to 1400 stitches/min., depending on stitch length and speed of conveyor as well as on operation and material.
BEFORE USING 1.
Before use, please clean the grease and dust on the surface of the machine with petro and soft cloth.
2.
Before use the machine, a through examine should be made to the machine. Rotate the pulley slightly by hand to see if every part moves smoothly. If any colliding or resistance happen, please make relative adjustment.
INSTALLING THE MOTOR Align machine balance wheel belt groove with motor pulley belt groove by moving the motor leftward or rightward. Be sure the belt is not touch with table.
CONNECTING THE CLUTH LEVER TO THE PEDAL (Fig. 1) The optimum angle of pedal with floor is approx 15 degree. Adjust the clutch of the motor so that clutch lever (Fig.1, C) and draw bar (Fig.1, B) run in line. The machine would have stable motion and long using. The machine balance wheel should rotate corner clockwise for normal sewing when view from opposite side of the balance wheel. The motor rotates in the same direction. The rotation can be reversed by reversing (turn over 180 deg.) The plug of the motor. Adjust the tension of O-belt (Fig.1, F) by moving the motor vertically. The proper tension of V-belt is a slack of 10-12mm.
Fig. 1 -2-
OILING (Fig. 2)
Oil the machine every day throughly after finishing working according to (Fig.2), and run the machine for 1-2 minutes.
Fig. 2 TRIAL RUN When the machine left out of operation for a quite long time and used again, remove the red rubber plug on top of the machine head, oil it throughly, then lift the presser foot and run at a low speed of 1000~1500spm, observe the sparkling condition through oil window . As the lubrication is well, keep the running test at the low speed about 30 minutes, then increase the speed gradually, after months running to perfect its performance. Then increase up to roper sewing speed.
INSTALLING THE NEEDLE Turn the balance wheel to lift the needle bar to its highest point, loosen needle set screw, making the needle groove turn to the left side of an operator, fully insert the needle shank up to the bottom of needle socket, then tighten needle set screw.
COORDINATION AMONG THE NEEDLE, THE THREAD AND THE MATERIAL (Fig. 3) For needle thread left-hand twist thread should be used and for bobbin thread, both left and right could be used. To identify the handedness of the thread, pinch the thread like Fig. 9 shows, twist the thread with right hand to the direction as the arrow shows, if the strand gets tight with the twist, left-hand twist it is, otherwise right-hand twist. DDĂ—1 type Nm 25 needle should be used. The thickness of the needle should be suitable for the materials.If a very thin needle is used to sew heavy duty materials,the needle is easily to be broken, ship stitching and thread broken could also be resulted. In contrast, if a very thick needle is used,damage might be caused to the materials for the too big needle holes. So suitable needle should be choose according to the character of threads.
-3-
Fig. 3
THREADING THE NEEDLE THREAD (Fig. 4)
Thread the needle thread following (Fig. 4.)
Fig. 4 BOBBIN WINDER ADJUSTMENT (Fig. 5) Bobbin thread should be orderly and tight. If the bobbin thread is too loose, increase the pressure of disc A. If the bobbin thread is not orderly, adjust the position of thread passing rack C. To adjust, loosen screw B, if the bobbin thread is like picture (b) in the pictures below, move the thread passing rack to the right side; if like picture (c), to the left side. Till the bobbin thread is like picture (a), retighten the screw. Note.: Thread pressure should be decreased when winding polyester or nylon thread, otherwise the bobbin D will be broken or become out of shape. Bobbin thread should not be too full, otherwise thread will get off the bobbin because of too loose. Proper bobbin thread quantity should be 80% of the full bobbin thread. Bobbin thread winding quantity is adjustment by adjusting the screw E.
Fig. 5 6) ADJUSTING THE STITCH LENGTH (Fig. Fig.6) Loosen screw (A) , rotate stitch length adjusting connecting lever pin (B). Rotate (B) clockwise: forward stitch length is increased reverse stitch is decreased Rotate (B) anti-clockwise: forward stitch length is decreased reverse stitch is increased
Fig. 6 -4-
7) ADJUSTING THE PRESSURE OF PRESSER FOOT (Fig. Fig.7) Pressure on presser foot is to be adjusted in accordance with materials to be sewn. Loosen lock nut A. If heavy materials to be sewn,turn pressure regulating thumb screw clock wise as shown (a) to increase the pressure. While light materials to be sewn,turn the pressure regulating thumb screw counter clockwise as shown in (b) to decrease the pressure on presser foot, then tighten lock nut A.
The pressure of presser foot is proper as the sewing materials can be fed normally.
Fig. 7
ADJUST THE THREAD TENSION (Fig. 8) In general, the thread tension is to be adjust in accordance with material thread and others. In practice, the thread tension is adjusted according to the stitches resulted to get the normal stitches. When adjusting the bobbin thread tension, turn bobbin case tension spring screw A clock wise for more tension or turn the screw counter clockwise for less tension. It is a common practice to check the bobbin thread tension. If the bobbin case falls down slowly the proper tension is obtained. The needle thread tension should be adjusted with reference to the bobbin thread tension. The needle thread tension can be range of the thread take up spring tension of tension disc and the position of thread guide.
Fig. 8
TIMING BETWEEN THE NEEDLE AND THE ROTATING SHUTTLE (Fig.9 and Fig. 10) (1) Adjusting the position of needle bar turn the balance wheel to locate the needle bar at its lowest position, then turn the balance wheel and make the needle bar move upward by 4.5mm. At this time, the hook tip should be higher than the needle eyelet about 1.5mm, (Fig. 9). (2) Distance between groove of the needle and hook tip should be 0.05mm, (Fig. 10). (3) To adjust the height of the needle, loosen the needle bar connecting shaft screw, move the needle upward and downward by hand to get the required height, then retighten the screw.
-5-
Fig. 10
Fig. 9
REMOVING AND INSTALLING THE ROTATING SHUTTLE (Fig. 11) Lift the needle bar to its highest position, remove the throat plate, take down the needle and the bobbin case, loosen rotating shuttle bobbin case holder position bracket screw C and take down position bracket A, then loosen set screws B of rotating shuttle to keep hook freely, turning around its axis, turn the balance wheel first to raise the feed bar to its highest position, at this time, take down the rotating hook slowly while turning it to keep away from the feed dog support. Installing the rotating hook can be done in reverse sequence.
Fig. 11 The projecting flange of the position bracket A should be engaged in the notch of the bobbin case folder, and maintain a clearance of 1.1 - 1.13mm between projecting flange top and the bottom of notch while.
LING THE ROTAT ING HOOK POSITION LIMIT SOCKET (Fig. 12) INSTAL INSTALLING ROTATING
When installing the position limit socket E, first loosen screw D. Adjust the distance between position limit socket and rotating hook be 1.2-1.5mm, and distance between position limit spring and bobbin case is 1-1.12mm. Make sure C does not touch hoop tip B.
Fig. 12 -6-
INSTALLING FEED DOG (Fig. 13 and Fig. 14)
Fig. 13
Fig. 14
When feed amount is at the max. The front end of feed dog A is near the front of throat plate slot, the gauge between the two is 1.5mm. This is the standard position of feed dog. To adjust the position of feed dog (Fig. 14), move feed dog to the front end of throat plate, Loosen Screw A, move feed dog support B in the direction shown by arrow to adjust. After adjustment tighten screw A.
TIMING BETWEEN THE NEEDLE AND FEED-DOG (Fig. 15 and Fig. 16) 1. Standard position (Fig. 15). Turn the shaft wheel, low the position of feed dog A, when the feed dog is parallel, Needle C point needle plate and feed dog are now aligned. Adjustment could be done by adjusting installing position of the feed cam and feed lifting cam. 2. Installing of the feed cam (Fig. 16). Open the back cover, uninstall the oil baffle plate, turn the shaft wheel anti-clockwise by left hand. The center for second screw of the feed cam C should be in a straight line to the needle bar center, and parallel the main shaft. 3. Installing of feeding lifting cam. (Fig. 16) Rotate the feed lifting cam anticlockwise, make the of feed cam and needle bar in one straight line.
center of the first screw B, center of the second screw C
Fig. 15
Fig. 16
-7-
ADJUSTING PRESSER BAR CROSS LIFTING MECHANISM (Fig. 17) In the process of sewing, the cross lifting height of alternating presser foot and small presser foot could be adjusted in a certain range according to different extent of looseness and tightness of the materials. Loose eccentric wheel link lever adjusting crank screw A, turn the presser foot lifting crank upwards as the picture shows, the alternating presser lifting height increases, otherwise, turn the crank downwards, the lifting height of the small presser foot decrease. But the adjusting quality is in a certain limit, not too big. When the adjustment is finished, tighten the screws up, turn the arm shaft wheel with hand, inspect everything. Run the machine only after everything is OK.
Fig. 17 ADJUSTING TOTAL LIFTING HEIGHT OF ALTERNATING AND PRESSER FOOT (Fig. 18)
In the precess of sewing, the front of alternative presser foot groove should not hit the back of small presser foot, and keep distance C (usually about 1.5mm). When sewing with small thread length, the alternative presser foot should be move a little to the needle bat. Adjust method: Loosen the screw of back crank for the alternative shaft, rotate the alternative shaft upward. Pay attention fo the distance C.
Fig. 18 CLEARING THE MACHINE REGULARLY (Fig. 19) Clean the feed dog, rotate shuttle and bobbin case regularly.
1. Clean the feed dog. Remove the needle plate, clean feed dog A, then install the feed dog.
2. Clean the rotate shuttle as shown in the picture B.
-8-
Fig. 19
-9-
PARTS MANUAL FOR HEAVY DUTY SEWING MACHINE
- 10 -
01 CASTING HOUSING
- 11 -
01 CASTING HOUSING
Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42
Part No. 260101 260102 260103 260104 206105 260106 260107 260108 260109 260110 260111 260112 260113 260114 260115 260116 260117 260118 260119 260120 260121 260122 260123 260124 260125 260126 260127 260128 260129 260130 260131 260132 260133 260134 260135 260136 260137 120138 120139 120140 120141 120142
Description Face cover Screw Thread guide Thread guide Screw Thread eyelet Thread tension post Thread tension disk Thread tension spring Nut Thread eyelet Arm cover, right Arm cover, left Back cover Thread releasing pin Set screw Thread tension base Thread regulating spring Thread take-up spring Regulating disk Thread tension post Thread tension disk, inner Thread tension disk, outer Thread releasing disk Thread tension spring Nut Sliding plate, right Screw Needle plate Screw Sliding plate, left Sliding plate fitting Screw Screw Thread tension ass’y Thread tension ass’y Screw Washer Screw Screw Thread guide Screw - 12 -
Qty 1 4 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 1 2 2 1 1 1 1 1 4 1 1
Remarks
02 NEEDLE BAR AND UPPER SHAFT
- 13 -
02 NEEDLE BAR AND UPPER SHAFT
Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
Part No. 260301 260302 260303 260304 206305 260306 260307 260308 260309 260310 260311 260312 260313 260314 260315 260316 260317 260318 260319 260320 260321 260322 260323 260324 260325 260326 260327 260328 260329 260330 260331 260332 260333 260334 260335 260336 260337 260338 260339 260340 260341
Description Needle Needle bar bushing, lower Needle set screw Needle bar bushing, upper Set Screw Needle bar Needle bar connecting rod Take-up thread connecting rod Take-up thread connecting pin Needle bar connecting pin Thread take-up lever Thread take-up lever bearing Thread take-up lever bolt Thread take-up crank Set screw Screw Slider slot Sliding block Screw Collar Pin Screw Pin Set screw Needle bar crank Set screw Sleeve, front Sleeve, rear Sleeve, middle Felt Felt Arm shaft Set screw Feed dog lift eccentric Feeding eccentric Feeding eccentric side plate Screw Arm shaft bevel gear Vertical shaft bevel gear, upper Vertical shaft bevel gear, lower Screw
- 14 -
Qty 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 1 1 1 2 2 1 1 1 1 1 10 1 1 1 2 1 1 7 1 1 1 2 1 1 1 2
Remarks
02 NEEDLE BAR AND UPPER SHAFT (CONTINUE)
Ref. No. 41B 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57
Part No. 260341B 260342 260343 260344 260345 260346 260347 260348 260349 260350 260351 260352 2603533 260354 260355 260356 260357
Description Set screw Vertical shaft Feed dog lifting connecting rod Feeding connecting rod Vertical shaft bushing, lower Vertical shaft bushing, upper Oil tube Hand wheel Oil felt Spacing Reed Screw Screw Screw Collar Screw Screw Oil tube
- 15 -
Qty 1 1 1 1 1 1 1 1 2 2 2 3 1 1 3 3 1
Remarks
03 UPPER FEED MECHANISM
- 16 -
D MECHANISM 03 UPPER FEE FEED
Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
Part No. 260501 260502 260503 260504 206505 260506 260507 260508 260509 260510 260511 260512 260513 260514 260515 260516 260517 260518 260519 206520 206521 206522 206523 206524 206525 206526 206527 206528 206529 206530 260531 260532 260533 260534 260535 260536 260537 260538 260539 260540 260541
Description Presser foot lifting shaft Bushing Screw Crank, front Screw Crank, rear Screw Eccentric connecting rod Eccentric cam Screw Screw Nut Nut Nut Screw Screw Presser foot lifting rocker Presser bar Guide plate Screw Alternant presser foot Screw Alternant presser foot connecting rod Bolt Fork lever Connecting rod Nut Screw Bolt Oscillating shaft crank, front Taper Pin Bolt Oscillating shaft bushing, front Sliding block Washer Oscillating shaft bushing, rear Oscillating shaft collar Screw Oscillating shaft Oscillating shaft crank, rear Oscillating connecting rod
- 17 -
Qty 1 2 4 1 1 1 1 1 1 4 1 1 1 2 1 4 1 1 1 2 1 1 1 2 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1
Remarks
D MECHANISM 03 UPPER FEE FEED (CONTINUE)
Ref. No. 42 43
Part No. 260542 260543
Description Connecting pin Screw
Qty 1 1
- 18 -
Remarks
04 BOTTOM SHAFT
- 19 -
04 BOTTOM SHAFT
Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
Part No. 260701 260702 260703 260704 206705 260706 260707 260708 260709 260710 260711 260712 260713 260714 260715 260716 260717 260718 260719 260720 260721 260722 260723 260724 260725 260726 260727 260728 260729 260730 260731 260732 260733 260734
Description Main shaft bevel gear Screw Bushing, rear Screw Felt Collar Screw Shuttle base Bushing, front Shuttle race Screw Bobbin Bobbin case ass’y Shuttle set bracket Screw Spacing base Bolt Spring Screw Spacing bracket Pin Spacing spring Screw Main shaft Rotating shuttle ass’y Bobbin case Shuttle body ring Spring Screw Spring Screw Screw Screw Spacing spring
Qty 1 2 1 2 2 2 4 1 1 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1
- 20 -
Remarks
05 FEED REGULATING MECHANISM
- 21 -
05 FEED REGULATING MECHANISM Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
Part No. 260901 260902 260903 260904 206905 260906 260907 260908 260909 260910 260911 260912 260913 260914 260915 260916 260917 260918 260919 206920 206921 206922 206923 206924 206925 206926 206927 206928
Description Feed rocker Connecting pin Screw Screw Feed rocker crank Bolt Feed dog lifting sliding block Feed dog Feed dog lift shaft crank, rear Feed rocker shaft Bushing, front Bushing, rear Middle bushing, left Middle bushing, right Feed shaft rear crank Screw Feed crank Pin Screw Feed dog lift shaft Bushing, front Bushing, rear Set screw Feed rocker shaft crank, front Screw Screw Nut Screw
- 22 -
Qty 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 2 1 1 1 2 5
Remarks
06 FEED MECHANISM
- 23 -
06 FEED MECHANISM
Ref. No.
Part No.
Description
Qty
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
261101 261102 261103 261104 261105 261106 261107 261108 261109 261110 261111 261112 261113 261114 261115 261116 261117
Pin Stitch adjusting bracket Screw Screw Sleeve Stitch adjusting bracket shaft Rubber plug Set screw Back tack lever crank Pin roller Spring Screw Back tack lever Pin Screw Screw
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Screw
1
18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
261118 261119 261120 261121 261122 261123 261124 261125 261126 261127 261128 261129 261130 261131 261132 261133 261134 261135 261136 261137 261138 261139 261140 261141
Screw Stitch adjusting rod O type rubber ring Stitch adjusting knob Stitch adjusting panel Washer Screw Spacing pin Spring Spring hanger Screw Backs tack cylinder Stitch adjusting connecting rod Pin Connecting rod Screw Connecting rod Pin Screw Bearing Eccentric shaft Stitch adjusting crank Set pin, left Screw
1 1 1 1 1 1 1 1 2 1 1 1 1 1 2 1 2 1 2 1 1 1 1 2
- 24 -
Remarks
Optional
06 FEED MECHANISM (CONTINUE)
Ref. No. 42 43 44 45 46 47
Part No. 261142 261143 261144 261145 261146 261147
Description Set pin, right Push lever Spring Pin Set screw Back tack cylinder knockout pin
- 25 -
Qty
Remarks
1 1 1 1 4 1
Optional Optional
07 PRESSER FOOT LIFTER (1/3)
- 26 -
07 PRESSER FOOT LIFTER (1/3)
Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 12B 13 14 15 16 17
Part No. 261301 261302 261303 261304 261305 261306 261307 261308 261309 261310 261311 261312 261312B 261313 261314 261315 261316 261317
Description Presser foot lifter base Screw Pin Reset spring bracket Screw Set screw Connecting plate Pin Presser foot lifter Alternate presser foot lifter Handle ball Alternate presser foot lifter connecting bar Alternate presser foot lifter connecting bar E type ring Washer Presser foot lifter rod Set screw Reset spring
- 27 -
Qty 1 2 2 1 4 2 1 1 1 1 2 1 1 2 1 1 1 1
Remarks
Optional
08 PRESSER FOOT LIFTER (2/3)
- 28 -
08 PRESSER FOOT LIFTER (2/3)
Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17A 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 38B 39
Part No. 261501 261502 261503 261504 261505 261506 261507 261508 261509 261510 261511 261512 261513 261514 261515 261516 261517(A) 261517 261518 261519 261520 261521 261522 261523 261524 261525 261526 261527 261528 261529 261530 261531 261532 261533 261534 261535 261536 261537 261538 261538(B) 261539
Description Presset foot lifer bar Screw Presser bar lift lever (A) Screw Presser bar lift lever (B) Connecting rod Screw Connector Nut Presser bar lift spring Screw Screw Knee lifter lever Screw Roller pin Screw Connecting plate Hanger Screw Presser bar guide bracket Screw Presser foot lifter cylinder ass’y Washer Thread guide Set screw Spring Thread guide base Screw Pin Spacing block Screw Nut Presser bar flat guide bracket Screw Presser bar Spring Screw Nut Presser foot Presser foot with filler cord guide Air cylinder
- 29 -
Qty 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1
Remarks
Optional
Optional Optional
08 PRESSER FOOT LIFTER (2/3) (CONTINUE)
Ref. No. 40 41 42 43 44 45 46 47 48
Part No. 261540 261541 261542 261543 261544 261545 261546 261547 261548
Description Air cylinder base Nut Lifter rod Connector Screw Screw Screw Spring Set screw
- 30 -
Qty
Remarks
1 4 1 1 1 1 1 1 1
Optional Optional Optional Optional Optional Optional
Optional
09 PRESSER FOOT LIFTER (3/3)
- 31 -
09 PRESSER FOOT LIFTER (3/3)
Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
Part No. 261701 261702 261703 261704 261705 261706 261707 261708 261709 261710 261711 261712 261713 261714 261715 261716 261717 261718 261719 261720 261721 261722
Description Connector A Connecting rod Connector B Connecting spring Knee lifter shaft Pin Spring bracket Spring Connector Knee lifter crank Screw Screw Screw Screw Screw Screw Screw Knee lever rod Kneel lifter bar Kneel lifter bracket Set bracket Screw
Qty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1
- 32 -
Remarks
10 OILING PARTS
- 33 -
ING PARTS 10 OIL OILING
Ref. No. 1 2 3 4 5 6 7 8 9 10
Part No. 261901 261902 261903 261904 261905 261906 261907 261908 261909 261910
Description Oil shield Screw Oil shield Oil cup, right Felt Oil tube, E Felt Oil wick Washer Screw
Qty 1 2 1 1 1 3 1 1 1 1
- 34 -
Remarks
11 ACCESSORIES
- 35 -
11 ACCESSORIES
Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
Part No. 262101 262102 262103 262104 262105 262106 262107 262108 262109 262110 262111 262112 262113 262114 262115 262116 262117 262118 262119 262120 262121 262122 262123 262124 262125
Description Machine head supporter Thread stand ass’y Parts bag Belt guard ass’y Screw Bolt Screw Screw Washer Oil pan V-belt Needle Screw driver (small) Screw driver (middle) Screw driver (big) Screw driver Oil can Nail Washer Allen wrench Allen wrench Allen wrench Allen wrench Rubber cushion Hinge
- 36 -
Qty 1 1 1 1 1 6 3 4 4 1 1 3 1 1 1 1 1 4 4 1 1 1 2 2 2
Remarks