XS Power D1200 Deep cycle 12-Volt Deep Cycle AGM Power Cell with 2600 Max Amps
XS Power D3100 12-Volt Deep Cycle AGM Power Cell with 5000 Max Amps
XS Power D3400 12-Volt Deep Cycle AGM Power Cell with 3300 Max Amps
XS Power D7500 12-Volt Deep Cycle AGM Power Cell with 6000 Max Amps
XS Power D680 12-Volt Deep Cycle AGM Power Cell with 1000 Max Amps
XS Power D975 12-Volt Deep Cycle AGM Power Cell with 2100 Max Amps
4
Key Features Extremely rigid non-pressed paper cone assembly Multilayered polymer wide roll foam surround Polypropylene dust cover with embossed DC logo 8� OD flat linear roll spider Heavy duty interweaved tinsel lead wire sewn to the spider Cast aluminum black frame FEA analyzed and optimized motor assembly - Fully CNC machined Rubber mounting gasket Chrome spring loaded push terminals 2.5� Hi-temp copper voice coil wound on black anodized voice coil former Rubber magnet cover With more power handling than before, the Level 2 is back and better than ever! This sub has everything you need in a daily driver except the cost. This is one of our greatest accomplishments.It starts out with a double-stacked FEA optimized motor. A chrome top plate and T yoke to keep it looking good. It has 22 mm of X-Max, progressive spider, 2.5" voice coil, cast basket, push terminals and a rating suggestion of 600w RMS/1200w peak power handling.
Key Features Extremely rigid non-pressed paper cone assembly Multilayered polymer foam surround Polypropylene dust cover with embossed DC logo Dual 8” OD semi cup progressive roll spider Extra heavy duty interweaved tinsel lead wire sewn to spider Cast aluminum black frame FEA analyzed and optimized motor assembly – Fully CNC machined Rubber mounting gasket Chrome spring loaded push terminals Dual 4 ohm 3” Hi-temp Aluminum voice coil wound on black anodized voice coil former Rubber magnet cover The level 3 sub is the ultimate daily driver sub. It puts out the low lows with lots of output designed for sealed or ported enclosures. The Level 3 sub is a triple stacked FEA optimized motor wrapped in a magnet boot, chrome top plate and T yoke. The deep gap offers more X-max for a total of 22.5mm. This sub also comes with dual upgraded progressive spiders, cone, surround, 3" voice coil, cast basket, push terminals, and upgraded sewn down lead wire. We give the Level 3 a power rating of 900w RMS/1800w peak.
Key Features
Extremely rigid non-pressed paper cone assembly Multilayered polymer foam surround Polypropylene dust cover with embossed DC logo Triple 8"OD semi cup progressive roll spider Extra heavy duty interweaved tinsel lead wire sewn down to spider Cast aluminum black frame FEA analyzed and optimized motor assembly – Fully CNC machined Rubber mounting gasket Chrome spring loaded push terminals 3� Hi-temp Edge wound aluminum voice coil wound on black anodized voice coil former Rubber magnet cover The Level 4 m2 was designed to take even more power and get even louder than the m1. With fantastic power handling and smashing lows its hard to beat. The Level 4 sub is a large triple stacked motor, wrapped in a magnet boot with a chrome top plate and T yoke yielding 23.5mm of X-Max. Furthermore, you get the upgraded triple progressive spiders, cone, surround, 3" coil, cast basket, push terminals and upgraded lead wire sewn to the spider. This sub is rated at 1400w RMS and 2800w peak.
Key Features
Extremely rigid non-pressed paper cone assembly Multilayered polymer foam surround Polypropylene dust cover with embossed DC logo Quad 8"OD semi cup progressive roll spiders Dual Extra heavy duty interweaved tinsel lead wire Cast aluminum black frame FEA analyzed and optimized motor assembly – Fully CNC machined Rubber mounting gasket Chrome spring loaded push terminals Dual 0.7, 1.0, 1.4 or 2 ohm 3" 8 Layer Hi-temp Aluminum Stealth Coil The XLm2 is the next generation of our most award winning driver. The XLm2 has more cooling, longer lasting spider packs, and about a 45% increase in the RMS rating over the Xlm1! Although this sub was already great to begin with, we took a lot of time to redesign constructive changes.
The 1.2kw competition series amplifier is a 1,200 watt mono block. It is capable of running up to 16 volts for up to1,450 watts. It is a linkable amp and designed to run a 1 ohm per amp or 2 ohms when strapped. It comes with a bass knob. For power inputs it will accept 4 awg for power and 4 awg for ground.
Key Features • 1 ohm stable • Variable low pass filter • Variable subsonic filter • Variable bass boost • Wired remote control • Dash mounted voltage meter We recommend for installation • 1 upgraded battery under the hood
The 2.0kw competition series amplifier is a 2,000 watt mono block. It is a linkable amp and designed to run a 1 ohm per amp or 2 ohms when strapped. It comes with a bass knob and a clipping indicator. For power inputs it will accept 0 awg for power and 0 awg for ground.
Key
Features
• 1 ohm stable • Variable low pass filter • Variable subsonic filter • Variable bass boost • Wired remote control • Clipping indicator
The 3.5kw competition series amplifier is a 3,500 watt mono block. It is capable of running up to 18 volts for up to 5,100 watts. It is a linkable amp and designed to run a 1 ohm per amp or 2 ohms when strapped. It comes with a bass knob and a clipping indicator. For power inputs it will accept 0 awg for power and 0 awg for ground.
Key Features • 1 ohm stable • Variable low pass filter • Variable subsonic filter • Variable bass boost • Wired remote control • Clipping indicator
The 5.0kw competition series amplifier is a 5,000 watt mono block. It is capable of running up to 18 volts for up to 7,300 watts. It is a linkable amp and designed to run a 1 ohm per amp or 2 ohms when strapped. It comes with a bass knob and a clipping indicator. For power inputs it will accept dual 0 awg for power and dual 0 awg for ground.
Key Features • 1 ohm stable • Variable low pass filter • Variable subsonic filter • Variable bass boost • Wired remote control • Clipping indicator • Dual 0 awg power and ground inputs (both must be used)