CATALOGUE OF PRODUCTS 2013

CATALOGUE OF PRODUCTS

2013

CATALOGUE OF PRODUCTS

2013

Content of product ADHESIVE

01

DW 1000 DW 1100 DW 2000 DW KLEBEMÖRTEL 2.5 DW 3000 DW EXTENSION DW GRANDFIX DW 2000 RAPID DW SELFWETTING DW VETROSYSTEM DW YTONG DW HOLZFIX DW MARMOFLEX DW FLEXTERIOR DW URBAN 40 DW CONEXION 77 DW CONEXION 99

02

FUGA COLOR 0-5 MEGAFUGA 3-20

03

FIBREN GP-70 YTONG PUTZ + MORTAR FOR PLASTERING MORTAR FOR MASONRY GIPSPUTZ

12 14 16 18 20 22 24 26 28 30 31 32 34 36 42 48 50

GROUTS FOR JOINTS 54 56

MORTARS 60 62 64 66 68

REFINISHES

04

FINO CLASSIC BONIFIN ACRYL SPACHTEL SPATORELLA SPATORELLA GIPS

05

GRAFIATO ACRYL DECORTEX GRAFIATO DECORTEX MINERAL

06

IZOELASTIC LIQUID DW IZOL IZOBAND IZOELASTIC IZOFLEX MONOFLEX MONOLIT IZOTRATE

07

TECNOFIX TECNOFIX LIQUID DW PRIMER HYDRO PRIMER BETON CONTACT GIPS PRIMER

08

DW 17 FLEXIT LATEX PLASTOLIT

72 74 76 78 80

DECORATIVE COATINGS 84 86 88 90

WATERPROOF COATINGS 94 96 97 98 100 102 104 106

PRIMERS 110 112 114 115 116 117

ADDITIVES

120 121 122 123

LEVELLING COMPOUNDS

09

TECNO FLOOR FLATEX

10

SILICONE, FOAM FIBERGLASS MESH

126 128

EXTRA PRODUCTS 130 132

About us DAST is not only a passionate producer of qualitative construction and repairing materials but of anything connected to living and working in comfortable and healthy environments. What we do is providing a strong and stable base and a smart and full of flavor view for your family, work and play environments. Find us and you will get convinced that we are more than what we create. Everything start with meeting DAST and a long lasting friendship relationship will start because we are devoted to understanding what you are looking for and we can offer you the choice you make. It is not uncommon that customers congratulate us friendly.

Our partners are our orientation of the social life in cities and villages, where the best professionals and technicians of industry meet. Our distributors offer our safe product because they expect that the client comes back to congratulate. Because our clients know they can trust our strict quality, a sincere service and a total commitment.

Thus DAST is not only a passionate producer of qualitative construction and repairing materials but a community of proud and satisfied people, ambitious and challenging and

Developing Ecological Technology

professionals always in search of new energies. DAST sh.a is a German-Albanian consortium created by the combination of experience, technology, deep knowledge of the market, outstanding entrepreneurial skills and financial potential. Established in January 2008, DAST has grown quickly and has taken a leading position in Albania and a wide recognition in the Balkans. DAST products are traded in Germany, Italy, Greece, Albania, Macedonia, Montenegro, Kosovo, Lebanon, Belgium and beyond.

Autostrada Tiranë - Durrës Km. 30, Shqipëri, Tel: +355 52 25 25 25, Fax: +355 52 25 25 26, e-mail: info@dast.al, www.dast.al

DAST product portfolio includes tile adhesives, fuges’fillers, decorative outfits, mortars, room finishes, products based Gypsum, auto levelers, hydro isolators, as well as the silicones, additive amplifiers, acid cleaners, nets, bars and other accessories applicable in flooring tiles, wall decorative coating, realization of the refinishes, different bricks and blocks sticking, brick and block walls filling, flattening and leveling, and hydro isolation of horizontal and vertical surfaces, in internal and external environments at variable weather conditions.

Our Research and Development department is a forefront function in designing and projecting new solutions. Our laboratories are equipped with the latest technology and procedures, in line with our mission to anticipate market demand with smart and sustainable solutions. A research team composed of engineers works continuously to find solutions. The production technology is thoroughly modern and manageable through an integrated electronic system. Manufacturing, packaging and control functions are fully automated and controlled by electronic sensor system. Our products are certified according to EN technical standards and the quality management is done according to ISO 9001 standards. The customer service is very accurate and devoted to the customer’s need based on what the latter’s viewpoints are.

This is the reason why DAST is not only an passionate producer of qualitative construction and repairing materials, but a community of proud, satisfied people, ambitious professionals always in search of new energies.

ACADEMY The company Dast sh.a has created Dast Academy, which is the first academy in Albania and the region that gives training courses / seminars in the field of construction. This academy offers a broad range of professional certification and graduate programs through cooperation with renowned partners abroad In support of the construction industry.

The purpose of organizing these seminars with professionals in the construction field are: • Introduce participants to the Dast sh.a, its 4-year activity, research and development work in laboratories, manufac turing processes, advanced technology and dedicated staff.

• Informing specialists in the field of construction on the products manufactured by this company, advantages and benefits of their applications.

• Introduction of new products generated in the laboratory, in order to improve living conditions.

• Demonstration of professional applications and knowledge of improved techniques.

• Counseling from the best professionals in the field and share the experiences of the participants in these seminars.

For all participants in these seminars Dast Academy issues certificates that prove the benefit of the knowledge acquired. The Dast sh.a certificates offer full warranty for the use and application of its products.

If you have questions about our products and operations, please do not hesitate to contact us at our address: info@dast.al

LABORATORY DAST believes in the added value of European Technology and Engineering Standards. This is the reason why our products dominate every market where traded. M-tec technology, technical standards EN and ISO 9001 quality standards help us to provide valuable solutions at competitive prices. Because we do not pay for the mistakes, because the technology is fully automated and designed to implement strict technical standards EN and does not make mistakes.

M-tec production lines installed in our factory, have a production capacity of 50 tons / hour. M-tec production technology has the advantage that it does not require installations at heights. Individually programmed controllers, associated with mechanical components, guarantee maximum accuracy of the system. M-tec technology is suitable for mass production, realizes weighing heavy components products recapture and realizes automatic transportation to mixing silos. It is equipped with a flexible dosage of additives (FAD).

Powerdose is a fully automatic dosing system. DAST uses it for high precision dosing of materials in bulk, as powders and granular materials, particularly for materials in the form of powder with poor quality flow. Latest Technology visualizing control by which can be controlled independently from the overall system controller, adding precise dosage in extremely small quantities with a precision up to + / -1 gram, leading to 0 the possibility of error and distortion products. Precision is independent of the material’s volume, while DAST manages to minimize the amount of raw materials by completely avoiding losses and damages.

The forefront technology in the manufacturing industry of building materials, repair and maintenance of residential premises, work and play, are a strong point of DAST and an added value for our products; a greater advantage to our customers and higher living quality for people.

THE SYSTEM OF TILES FLOORING IN INTERIOR AND EXTERIOR AREAS

■ DW 1000 ■ DW 1100 ■ DW 2000 ■ DW KLEBEMÖRTEL 2.5 ■ DW 3000

■ DW GRANDFIX ■ DW 2000 RAPID ■ DW SELFWETTING ■ DW VETROSYSTEM

■ DW EXTENSION ■ DW YTONG ■ DW HOLZFIX ■ DW MARMOFLEX

01 ADHESIVE DW 1000

E

CONSUM C1

2

3-5 kg/m

It is equipped with optimum adhesive abilities in every kind of traditional supports and it has good waterproofing characteristics. It is allowed to apply it to layers of 5mm. the strengthening is uniform, no shrinkage and layer holes. Classified according to EN12004, category C1.

APPLICATION AREA Appropriate for the ceramics tiles, gres porcelain, and cement based floors for exterior and interior environments.

Elasticizing In order to lay tiles in unstable surfaces as a result of the swelling or contraction or of vibration such as gypsum tiles, terraces, balconies, etc. it is necessary that 25kg of tiles’ adhesive DW 1000 be elasticized by adding 5-6kg FLEXIT (read technical data FLEXIT page 119) and the amount of water depending on the workability demand.

Preparation of the support Cement based supports Cement based traditional supports must have a maturation time of 28 days at a temperature of 23°C and U.R 40%. The supports must be flat and stable according to the use purpose. The support where the product will be applied must be clean without foreign substances such as: paints, oils, varnishes, material anti adhesives. Cleaning can be done mechanically or manually. Water must be sprayed on the

12

support before applying the adhesives in order to have the necessary time of drying.

Tiles laying It is recommended that initially the product laying on the support be implemented with the straight part of the commodity and later with the serrated part in order to obtain the best application of the product and a good and uniform spread in the whole surface. The product can be applied with an appropriate commodity depending on the type and dimensions of the tiles. It is recommended to use pressure after laying the tiles in a way that the back part be wet totally. In particular conditions such as high temperatures or strong winds, sun or support which strongly absorb water and have a negative effect in the product’s performance can lower significantly the time of spreading and correction and in order to avoid such problems it is recommended that the support be sprinkled with water before applying the adhesive or be treated with the liner DW PRIMER. It is important to check whether the adhesive has formed a membrane before laying the tiles. In such a case it is necessary spreading the adhesive in order to reactivate its adhesive characteristic. It is to avoid water in the adhesive substances which have created a membrane (solidified) because in a case like this an anti adhesive layer is formed.

In the case of laying tiles and of floors in the outdoor environments especially in the case when the back part of the tiles is of relief it is advisable that the adhesive substance be spread even in the back part of the tiles and in the support too in order to avoid the creation of cavity in which water may penetrate or humidity may form what actually would cause breaking and removal of the tiles.

www.dast.al

01

TECHNICAL DATA (AT 23 C AND 50% U.R) 0

Form

Powder

Color

Grey/white

Preservation

12 months in original packing in a dry place

Combustibility

Incombustible

Water demand

6-6,5 liter water in 25 kg DW 1000

Density of fresh mortar

1.7 gr/cm3

pH of mixture

12

Pot Life

3-4 hours

Application temperature

+50C up to +350C

Open time

≥ 20 min

Correction time

15 min

Passing rate

after 24 hours

Pointing on walls

After 8 to 12 hours

Pointing on floors

after 24 to 36 hours

1 final data: Deformation rate

0

Adhesive strength in concrete

≥ 0,5 N/mm2

Adhesive strength after the action of ≥ 0,5 N/mm2 heat Adhesive strength after immersion ≥ 0,5 N/mm2 on water

2

Adhesive strength after freeze-melt ≥ 0,5 N/mm2 cycles Compression strength

≥ 7 N/mm2

Note Gypsum or anhydrite based supports must be almost dry, humidity must be less than 0.5%, the support must be stable. The surface where the product will be applied must be treated with DW PRIMER.

3

PACKING DW 1000 grey and white in sacks of a weight of 25 kg.

13

01 ADHESIVE DW 1100

E

CONSUM C1 T

2

3-5 kg/m

DW 1100 is equipped with an adhesive optimal ability in any kind of traditional support and has good water resistance qualities, as well as zero slipping level. It is allowed the application in layers up to 5 mm, solidifying is uniform, no shrinkage and no pitting in the layers. It is classified according to EN12004, category C1T. Application area It is appropriate for sticking ceramic tiles, gres porcelain and cement based flooring for exterior and interior environments.

Elasticizing Tiling the non-stable surfaces as a result of shrinkage and swelling or vibrations as the gypsum tiles, terraces, balconies etc. Is necessary that 25 kg of tiles’ sticking material DW1100 be elasticized by adding 5-6 kg FLEXIT (read the technical data page 119) and the quantity of water according to the workability requirement.

The preparation of the support Cement- based supports The traditional cement based supports must have an appropriate maturation time of 28 days at a temperature of 23°c and U.R 40%. The supports must be flat and stable according to the function of usage. The support where the product will be applied must be clean with no foreign substances such as: paints, oils, varnishes, anti adhesive

14

material. Cleaning is done mechanically or manually. The support should be sprayed with water before applying the adhesive material in order to allow proper drying time.

The tiles flooring In order to have the best application of the product as well as obtaining a good and uniform spread in the whole surface, it is recommended that the flooring of the product over the support be done with the straight part of the commodity and later with the serrated part. The product must be applied with an appropriate commodity in accordance to the type and size of the tiles. It is recommended that after flooring the tile the back side of it be pressured in order that it gets totally wet. Under special conditions such as high temperature or strong winds, sun or high water absorbing supports which have a bad effect in the product’s performance and can even lower the spreading and correction time. In order to avoid such problems it is recommended that the support be spread with water before applying the adhesive material or be treated with the primer DW PRIMER. However it is important to check whether the adhesive has formed the membrane before flooring the tiles. In such a case it is necessary to spread again the adhesive material in order to reactivate its adhesive characteristic. It is to avoid the contact of water with the adhesive material which has created a membrane ( it is solidified) because in such a case it is formed an anti adhesive layer. In the case of coatings and exterior flooring especially when the back part of the tiles has relief it is advisable that the adhesive material be spread in the back part of the tile as well and over the support in order to avoid she shaping of cavities where water can penetrate or humidity take place which at a later time may cause tile’s breaking or removal. www.dast.al

01

TECHNICAL DATA (AT 23 C AND 50% U.R) 0

Form

Powder

Color

Grey/white

Preservation

12months in original packing at a dry place

Combustibility

Incombustible

Water demand

6-6,5 liter water per 25 kg DW 1100

Density of fresh mortar

1.7 gr/cm3

Mixture ph

12

Time of workability

3-4 hours

Application Temperature

+50C to +350C

Open time

≥20 min

Correction time

15 min

Pointing on walls

After 24 hours

Pointing on floors

After 8 to 12 hours

Final solidifying

after 24 to 36 hours

1

final data Deformation rate

0

Adhesive strength in concrete

≥ 0,5 N/mm2

Adhesive strength after the heat ≥ 0,5 N/mm2 action Adhesive strength after immer≥ 0,5 N/mm2 sion in water Adhesive strength after the the ≥ 0,5 N/mm2 thaw-freezing cycles Resistance in pressure

2

≥ 8 N/mm2

consume 3 -5 Kg/m2 Packing DW 1100 grey and white in sacks of a weigh of 25 Kg.

15

01 ADHESIVE DW 2000

E

CONSUM C2 E

2

3-5 kg/m

DW 2000 has optimal adhesive power of any traditional support as well as good characteristics, water resistant and long workability time. It is recommended the application in layers of 5mm thickness. It uniform , no shrinkage and deformation of the layer. Classification according to EN12004. Category: C2E. Application area It is appropriate for the ceramic tiles and cement based cements, gres porcelain welding. Ceramic tiles for balconies and terraces, for interior and exterior areas, for flooring tiles over tiles and flooring tiles over stone materials it is to reinforce with the additive FLEXIT. Elasticizing Flooring tiles in unstable surfaces as a result of shrinking and inflation or vibrations such in the case of gypsum tiles, terraces, balconies etc. It is necessary that 25 kg of adhesive for tiles DW2000 be elasticized by adding 5-6 kg FLEXIT (read the technical data page 119) and the amount of water depending on the workability demand.

The preparation of the support Cement based supports Traditional cement based supports must have a maturation time of 28 days at a temperature of 23Ëš and U.R 40%. The

16

supports must be flat and stable according to the purpose of usage. The support where the product will be applied must be clean and out of foreign materials such as: paints, oilsm varnishes, anti adhesive materials . The cleaning is done mechanically or manually. The support must be sprayed with water before the adhesive material be applied in order to provide the necessary drying time.

The application of tiles For a best application of the product and in order to obtain a good and uniform spreading in the whole surface, it is recommended that initially the flooring of the product over the support be done with the straight part of the commodity and then with the serrated part. The product must be applied with an appropriate commodity depending on the type and size of the tiles. It is recommended that after flooring be pressured the tiles so that the back part be totally wet. Under special conditions as at high temperatures, strong winds, sun, or high absorbing water supports which negatively affect in the product’s performance by even lowering considerably the time of spreading and correction. In order to avoid such problems it is recommended that the support be sprayed with water before applying the adhesive material or be treated with the primer DW PRIMER. However it is important to check whether the adhesive material has formed the membrane before flooring the tiles.

In such a case it is necessary to spread again the adhesive material in order to reactivate its adhesive characteristic. It is to avoid the contact of water with the adhesive material which has created a membrane (it is solidified) because in such a case it is formed an anti adhesive layer. In the case of coatings and exterior flooring especially when the back part of the tiles has reliefs it is advisable that the adhesive www.dast.al

01

material be spread in the back part of the tile as well and over the support in order to avoid she shaping of cavities where water can penetrate or humidity take place which at a later time may cause tile’s breaking or removal.

TECHNICAL DATA (AT 230C AND 50% U.R) Form

Powder

Color

Grey/white

Preservation

12months in original packing at a dry place

Combustibility

Incombustible

Water demand

6-6,5 liter water per 25 kg DW 2000

Density of fresh mortar

1.81 gr/cm3

Mixture ph

12

Application temperature

+50C to +350C

Open time

≥30 min

Correction time

≥20 min

Passing rate

After 24 hours

Pointing on walls

After 8 to 12 hours

Pointing on floors

after 24 to 36 hours

Final solidifying

14 days

1

final data Deformation rate

Not deformable

Adhesive strength in concrete

≥ 1.0N/mm2

Adhesive strength after the heat ≥ 1.0N/mm2 action Adhesive strength after immer≥ 1.0N/mm2 sion in water

2

Adhesive strength after the the ≥ 1.0N/mm2 thaw-freezing cycles Compression strength

≥ 10 N/mm2

: The gypsum based supports must be almost totally dry, the values of the remaining humidity must be less than 0.5%, the support must be stable. The surface where the product will be applied must be treated with DW PRIMER. note

packing dw

3

2000 grey and white in sacks of 25 kg.

17

01 ADHESIVE DW KLEBEMĂ–RTEL 2.5

E CONSUM C2 T

2

3-5 kg/m

Cement based adhesive. Without vertical slippery. Ideal for gres porcelain tiles.

Technical Characteristics It is an adhesive in the form of powder characterized of very good adhesive abilities; very good on the surfaces with low absorbing qualities which are characterized of average deformation rate.

The product is characterized of a very good waterproofing and without vertical slippery.

It is appropriate for welding the ceramic tiles, gres and gres porcelain over cement based supports for interior and exterior environments.

It is classified in the category C2TE of adhesives according to EN12004.

Application Area It is appropriate for welding the ceramic tiles, gres porcelain, clinker, monocotto, bicotto and natural stone on cement based walls and floors for interior and exterior environments; for welding the ceramic tiles in balconies, terraces and for flooring the tiles on floors with heavy traffic. When flooring tiles over tiles and over natural stone material, on plasterboard, environments with humidity and flooring tiles on floors with central system heating must be reinforced with the additive FLEXIT.

18

Elasticizing In order to cover with tiles surfaces which are unstable because of shrinkage and inflation and vibrations such as in the case of prefabricated concrete tiles, gypsum tiles, wooden floors or surfaces, floors with heating , balconies, metallic surfaces etc. It is necessary that 25 kg of adhesive material for tiles DW KLEBERMĂ–RTEL 2.5 be elasticized by adding 5-6kg of Flexit ( read the technical data FLEXIT page 119) and the quantity of water according to the workability requirement.

The preparation of the support Cement based support The traditional cement based supports must have a maturation time of 28 days at a temperature of 23°C and U.R 40%. The supports must be flat and stable according to the purpose of use. The support where the product will be applied must be clean, without foreign substances such as: paints, varnishes, anti adhesive materials. The cleaning can be done mechanically or manually. The support must be sprayed with water before applying the adhesive material in order to give it the necessary time for drying.

Tiles Flooring For the best application of the product as well as for obtaining a good and uniform spread in the whole surface, it is recommended to initially put the product over the support with the straight side of the commodity, and then with its serrated part. The product must be applied with an appropriate commodity according to the type and size of the tile.

It is recommended to exercise pressure on tiles after being placed in a way that the back side be all wet.

Under particular conditions such as: high temperatures or strong winds, sun or high water absorbing subtracts which negatively affect in the performance of the product and can www.dast.al

01

even significantly lower the spreading and correction time, in order to avoid such problems it is recommended that the support be sprayed with water before applying the adhesive material or be treated with the liner DW PRIMER. It is important to check whether the adhesive material has created a membrane before flooring the tiles. It is to avoid pouring the water in the adhesive material which has created a membrane (which is solidified) because in such a case an anti adhesive layer is formed.

In the case of flooring the floors in exterior environments especially in the cases when the back side of the tiles has a relief it is advisable that the adhesive material be spread in the back sides of the tiles too and in the support in such a way that no cavities be formed where water may penetrate or humidity may take place which may later cause removal or even the breaking of tiles.

Technical Data (at 230C and 50% U.R) Form

Powder

Color

Grey/white

Preservation

12 months in original pascking in a dry place

Density of fresh mortar

1.6 gr/cm3

Safety

Irritating

Water demand

7.5-8 L water for every 25 kg Klebemortel 2.5

Pointing on floors

After 24 to 36 hours

Duration of the mixture

More than 8 hours

Final solidifying

afte 14 days

Application Temperature

+50C to +350C

Mixture pH

12

Open time

≥ 30 min

Correction time

≥ 20 min

Passing rate

After 24 hours

Pointing on walls

After 4 to 8 hours

FINAL DATA

1

Deformation rate

High

Adhesive in concrete

≥ 1,0N/mm2

Adhesive strength after the heating action

≥ 1,0 N/mm2

Adhesive strength after immersion in water

≥ 1,0 N/ mm2

Adhesive strength after the thawfreezing cycles

≥ 1,0 N/ mm2

Stability against humidity

Very good

Stability against aging

Very good

: Gypsum or anhydride based supports must be almost totally dry, the values of the remaining humidity must be less than 0.5%, the support must be stable. The surface where the productis applied must be stable. The surface where the support is applied must be treated with DW PRIMER. note

2

PACKING DW Klebemörtel 2.5 grey and white in sacks of 25 kg.

19

01 ADHESIVE DW 3000

E

CONSUM C2 TE

2

3-5 kg/m

Cement based sdhesive of high performance, no vertical slipping rate and long time of spreading. Ideal for welding tiles in facades.

Technical Characteristics Powder adhesive with optimal sticking abilities in surfaces of low absorption and deformation. It is water resistant and it has zero vertical slippery rate. It is appropriate especially for non absorbing tiles, floors subject of continuous traffic and for flooring over tiles.

It is appropriate for interior and exterior usage.

Classified according to EN 12004, Category C2TE. Application area It is appropriate for the ceramic tiles’ welding, clinker, monocotto, bicotto and natural stones on walls and cement based floors for interior and exterior environments characterized of high rate of humidity, for the ceramic tiles welding in balconies and terraces, for the welding of tiles on floors of high traffic, and for flooring tiles over tiles. For the flooring of tiles on materials made of natural stone, over plasterboard, wet environments and flooring tiles on floors with central heat system it is necessary to reinforce with the additive FLEXIT. Elasticizing Flooring with tile the unstable surfaces because of shrink-

20

age and inflation or vibrations as in the case of prefabricated concrete tiles, gypsum tiles, wooden floors or surfaces, central heat system floors, terraces, balconies, fountains or small pools, metallic surfaces etc it is necessary that 25kg of tiles’ adhesive material DW3000 be elasticized by adding 5-6kg FLEXIT ( read the technical data flexit page 119).

The preparation of the support Cement based supports Traditional cement based supports must have a maturation time of 28 days at a temperature of 23Ëš and U.R 40%. The supports must be flat and stable according to the purpose of usage. The support where the product will be applied must be clean and out of foreign materials such as: paints, oilsm varnishes, anti adhesive materials . The cleaning is done mechanically or manually. The support must be sprayed with water before the adhesive material be applied in order to provide the necessary drying time.

Tiles Flooring It is necessary that for a correct application of DW 3000 applying a light layer of adhesive material with a serrated comb, then apply the adhesive material with a serrated commodity appropriate for the required thickness of the layer, for the severity of the support and for the type of the tile which will be welded. Press carefully the tile after it has been floored in a way that the back part be wet totally.

Special conditions such as strong wind, high temperature, strong sun or high water absorbing supports may reduce the spreading and correction time in a few minutes. It is recommended that the support be wet before applying the adhesive material. However it is important to check www.dast.al

01

whether the adhesive material has formed the membrane before flooring the tiles. In such a case it is necessary to spread again the adhesive material in order to reactivate its adhesive characteristic. It is to avoid the contact of water with the adhesive material which has created a membrane (it is solidified) because in such a case it is formed an anti adhesive layer. In the case of exterior walls and floors especially when the back part of the tile is too much structured or is a clinker tile, terracotta etc spread the adhesive material in the back part as well in order to avoid the unfilled holes where water can penetrate or humidity be condensed as this may cause the removal or breaking of the tiles in time of freezes.

TECHNICAL DATA (AT 230C AND 50% U.R) Form

Powder

Color

Grey/white

Preservation

12months in original packing at a dry place

Combustibility

Incombustible

Water demand

7-8 liter water per 25 kg DW 2000

Density of fresh mortar

1.6 gr/cm3

Mixture ph

12

Application Temperature

+50C to +350C

Open time

≥35 min

Correction time

≥25 min

1

The passing rate

After 24 hours

Pointing on walls

After 8 to 12 hours

Pointing on floors

after 24 to 36 hours

Final solidifying

14 days

final data Deformation rate

Non- deformable

Adhesive strength in concrete

≥ 1.0N/mm2

Adhesive strength after the heat ≥ 1.0N/mm2 action Adhesive strength after immer≥ 1.0N/mm2 sion in water

2

Adhesive strength after the the ≥ 1.0N/mm2 thaw-freezing cycles Compression strength

≥ 10 N/mm2

: The gypsum or anhydride based supports must be almost totally dry, the values of the remaining humidity must be less than 0.5%, the support must be stable. the surface where the product will be applied must be treated with dw primer. note

3

PACKING DW 3000 grey and white in sacks of 25 kg.

21

01 ADHESIVE DW EXTENSION

E

CONSUM C2 TE

2

/m 0.85 kg m per 1m

DW EXTENSION is a cement based adhesive for tiles, lightened with additive covering capability, without vertical slippery; long time of spreading and very good workability, classified according to EN12004, C2TE category.

Technical Characteristics Appropriate for tiles flooring on walls, cement based supports in interior and exterior environments.

It is a tile’s adhesive lightened 30% more compared to the other adhesives by ensuring this way a high covering and lower consume compared to other adhesives.

Important notes Do not use it on gypsum or anhydride bases Do not use it in prefabricated concrete elements Do not use it on metallic surfaces Do not use it in structures subject to strong movements The preparation of mixtures Mix 25 kg DW Extension with 10 liters of water through an electric mixer of 500 rotations per minute until obtaining a homogenous mass. The mass should be left for 5 minutes and be mixed again before using it. The obtained mass is ready for use in about 2-3 hours.

22

The preparation of the support Cement based floors The cement based floors must have a normal maturation of 28 days at a temperature of +23°C and U.R 50%. The supports must be flat and stable, dimensionally and mechanically resistant according to the purpose of usage, clean of oil remaining, oils or varnishes, wax and anti adhesive materials. The cleaning of oils, varnishes, wax or anti adhesive materials must be realized mechanically or manually. The supports must be dry enough: in case of humidity the adhesive may slow down the process of solidifying.

Plasters The plasters must be matured at least once a week for 1 cm thickness. The supports must be perpendicular and mechanically resistant according to the purpose of usage, without friable pieces and free of oils, varnishes, wax and anti adhesive materials. The cleaning of oils, varnishes, wax and anti adhesive materials must be realized manually or mechanically. The supports must be dry enough: in case of humidity the adhesive may slow down the process of solidifying.

Flooring the tiles It is recommended to initially spread a light layer of the adhesive material with a free commodity for a correct application of the DW Extension. Then start applying the adhesive material with a serrated commodity appropriate for the layer’s thickness you want to have, depending on the tiles format and its back side configuration.

Special environmental conditions: sun raises, strong wind, high temperature or high absorbing supports may reduce in a drastic way the spreading and correction time. In order www.dast.al

01

to prevent such problems it is advised to wet the support before flooring the adhesive. However it is necessary that the adhesive be verified not to be solidified. In case it is solidified the adhesive must be spatulated in order to reactivate the adhesiveness.

Technical data (at 230C and 50% U.R) Form

Powder

Color

Grey

Preservation

12 months in original packing at a dry place

Combustibility

Incombustible

Water demand

10 liters water for 25 kg DW Extension

Density of fresh mortar

1.2 gr/cm3

Mixture pH

12

Vertical slippery

≤ 0.5 mm

Application temperature

+50C to +350C

Open time

≥ 35 min

Correction time

≥ 30 min

Passing rate

After 24 hours

Pointing on walls

After 8 to 12 hours

Pointing on floors

1

After 24 to 36 hours

FINAL DATA : Deformation rate according to EN 0 12002 Adhesive strength in concrete ac≥ 1,0 N/mm2 cording to EN 1348 Adhesive strength after heating ac≥ 1,0 N/mm2 tion according to EN 1348 Adhesive strength after immersion in ≥ 1,0 N/mm2 water according to EN 1348 Adhesive strength after thaw-freeze ≥ 1,0 N/mm2 cycles according to EN 1348 Compression strength

≥ 10 N/mm2

CONSUME 0.85 Kg/m2 per mm thickness.

2

PACKING DW Extension grey and white in scaks of 25 Kg

23

01 ADHESIVE DW GRANDFIX

E

CONSUM C2 TE

2

3-5 kg/m

Cement based adhesive for flooring the clinker tiles, terracotta, gres and traditional tiles Technical characteristics Cement based powder like adhesive, selected granulometry sand, synthetic resins and special additives.

Long duration of workability, very good adhesiveness, good spreading and very good water retention.

Appropriate for flooring tiles in not very good leveled surfaces Appropriate for welding clinker tiles, terracotta, gres and traditional tiles in interior and exterior environments in supports with high rate of irregularities Elasticizing In order to floor the unstable surfaces because of shrinkage and inflation or vibrations such as in the case of prefabricated concrete tiles, gypsum tiles, terraces, balconies, metallic surfaces etc (read the technical data in page 119).

The mixture preparation Mix 6.5-7 liters of clean water with 25 kg of product; the obtained mass is recommended to be mixed with an electric mixer with low number of rotations until a homogenous mass of a certain viscosity and free of grains is formed.

The obtained mass is left at rest for 10 minutes and it is recommended to be mixed again before use. The workability time of the mixture is 5-6 hours.

24

The Preparation of the Support Cement based supports Traditional cement based supports must have a maturation time of 28 days at a temperature of 23°C and U.R 40%. The supports must be flat and stable according to the purpose of usage. The support where the product will be applied must be clean and out of foreign substances such as paints oils, varnishes and anti adhesive materials.

The cleaning is done mechanically or manually. The support must be sprayed with water before applying the adhesive material in such a way that it gives enough time to dry.

The tiles flooring For a correct application of DW GRANDFIX it is recommended that initially be spread a light layer of the adhesive with a free commodity. Then start applying the adhesive with a serrated commodity appropriate for the layer’s thickness you want depending on the tile’s format and on the configuration of its back side.

Special environmental conditions: strong sun rays, strong winds, high temperatures or high absorbing supports may reduce in a drastic way the spreading and correction time.

In order to prevent such problems it is advised to wet the support before applying the adhesive material or treat it with DW Primer. It is important however to check before flooring the tiles that the adhesive material be not solidified. In case it is, the adhesive material must be respatulated in order to reactivate the adhesiveness.

www.dast.al

01 Technical Data (at 230C and 50% U.R) Form

Powder

Color

Grey/white

Preservation

12 months in original packing at a dry place

Combustibility

Incombustibility

Water demand

6.5 -7 liter water for 25 kg DW Grandfix

Density of fresh mortar

1.81 gr/cm3

Mixture pH

12

Application Temperature

+50C to +350C

Open time

≥ 30 min

Correction time

≥ 20 min

Passing rate

After 24 hours

Pointing on walls

After 8 to 12 hours

Pointing on floors

After 24 to 36 hours

1

Final Data: Deformation rate

0

Adhesive strength on concrete

≥ 1,0 N/mm2

Adhesive strength after the heating ≥ 1,0 N/mm2 action Adhesive strength after the immer- ≥ 1,0 N/mm2 sion in water Adhesive strength after the thaw- ≥ 1,0 N/mm2 freezing cycles Compression strength

2

≥ 10 N/mm2

: Gypsum based supports or anhydride must be almost totally dry, the remaining humidity values must be less 0.5%, the support must be stable. The suface where the product will be applied must be treated with DW PRIMER. note

PCKING DW Grandfix grey and white in sacks of 25 kg.

25

01 ADHESIVE DW 2000 RAPID

E

CONSUM C2F

2

3-5 kg/m

Cement based adhesive Technical characteristics Cement based adhesive with high strength rate, granular selected sand, synthetic resin and special additives.

The short time of preza makes them very quickly ready for use the surfaces where it has been applied.

Good adhesive rate and non/absorbing materials.

Important notes Do not use it in gypsum or anhydrites basis Do not use it in prefabricated concrete elements Do not use in metallic surfaces Do not use it in marbles with unstable dimensions Do not use it in structures which are subject to strong movements The mixture preparation Mix 25 kg of DW 2000 Rapid in 6.5-7 litre of clean water through an electric mixer with 500 rotations per minute until a homogenous mass is obtained. The mass must be left for about 5 minutes and be mixed again before usage.

The mass obtained in this way is ready for use in 2-3 hours.

26

The preparation of the support Cement based floors Cement based floors must have a normal maturation of 28 days at a temperature of +23째c and U.R 50%. The supports must be flat and stable, dimensionally and mechanically resistant according to the purpose of usage, clean of oil remaining, oils, varnishes, wax and anti adhesive materials. The cleaning of oils, varnishes, wax and anti adhesive materials must be done mechanically or manually. The supports must be dry enough: in case of humidity the adhesive material may slow down the solidifying process.

The tiles flooring It is recommended to initially spread a light layer of the adhesive material with a free commodity in order to have a correct application of DW 2000. Then start applying the adhesive material with a serrated commodity appropriate for the thickness of the layer you want depending on the tiles format and its back part configuration. However it is necessary that in any case before flooring the tiles be verified that the adhesive material has not strengthened. In case it is strengthened the adhesive material must be spatulated again in order to reactivate the adhesiveness.

www.dast.al

01 Technical Data at 23°c and U.R 50%U.R Form

Dust

Color

Grey, white

Preservation

12 months in original packing in dry place

Combustibility

0

Water demand

6.5 -7 litre water per 25 kg DW Dw Grandfix

Density of fresh mortar

1.81 gr/cm3

Mixture pH

12

Application Temperature

+50C to +350C

Open time

≤ 25 min

Correction time

≤ 20 min

Passing rate

after 24 hours

1

final data : Deformation rate

0

Adhesive strength in con≥ 1,0 N/mm2 crete Adhesive strength after the ≥ 1,0 N/mm2 heat action Adhesive strength after the ≥ 1,0 N/mm2 immersion in water

2

Adhesive strength after the ≥ 1,0 N/mm2 thaw-freezing cycles Compression strength

≥ 10 N/mm2

Packing DW 2000 Rapid white and grey, on sacks of 25 Kg

3

27

01 ADHESIVE DW SELFWETTING

E

CONSUM C2 E

2

3-5 kg/m

DW Selfwetting with self wetting abilities and with a long spreading time. It is a cement based adhesive with a selected granulometry, resins and special additives. Classified according to EN12004, category C2E. Technical Characteristics Powder based adhesive with self wetting ability : a movement or a light oppression is enough in order to ensure 100% of the tiles dampening.

It enables a 3-20mm without any cavity.

It enables a time spare and it increases the work efficiency.

It is appropriate for flooring tiles when the temperatures of the environment are high.

Application area It is appropriate for flooring the ceramic based tiles on cement walls and floors in interior and exterior environments.

Important notes Do not use it on gypsum or anhydride basements.

Do not use it on prefabricated concrete elements.

Do not use it on metallic surfaces.

Do not use it for the placing of marbles of unstable dimensions.

Do not use it on structures subject to strong movements.

28

The preparation of the support Cement floors Cement based floors must have a normal maturation of 28 days at a temperature of +23°C and U.R 50%. The supports must be flat and stable, dimensionally and mechanically resistant according to the purpose of use, clean of oil remaining, oils and varnishes, wax and anti adhesive materials. The cleaning of oils, varnishes, wax and anti adhesive materials must be realized mechanically or manually. The supports must be dry enough: if there is humidity the adhesive material may slow down the process of solidifying.

Tiles flooring For a correct application of DW Selfwetting it is recommended to initially spread a light layer of adhesive material with a free commodity. Then start applying the commodity with a serrated commodity appropriate for the desired thickness, depending on the tile’s format and its back side configuration.

Special environmental conditions: sun rays, strong wind, high temperature or high absorbing supports may reduce in a drastic way the spread and correction time. It is necessary that before flooring the tiles, the adhesive material be verified of not being solidified. The adhesive material must be respatulated in order to reactivate the adhesiveness.

www.dast.al

01

Technical Data (at 23 C and 50% U.R) 0

Form

Powder

Color

Grey

Preservation

12 months in original packing at a dry place

Combustibility

0

Water demand

6-6,5 liter water for 25 kg DW Dw Selfwetting

Density of fresh mortar

1.6gr/cm3

Mixture pH

≥12

Workability time

4-5 hours

Applicaiotn Temperatura

From +50C to +350C

Open time

≥ 35 min

Correction time

≥ 30 min

Passing rate

After 24 hours

Pointing on walls

after 8 to 12 hours

Pointing on floors

After 24 to 36 hours

1

2

final Data Deformation rate

0

Adhesive strength on concrete

≥ 1,0 N/mm2

Adhesive strength after the heating action

≥ 1,0 N/mm2

Adhesive strength after immersion on water

≥ 1,0 N/mm2

Adhesive strength after the thaw-freezing cycles

≥ 1,0 N/mm2

Packing DW Selfwetting grey and white in sacks of 25 Kg

3

29

01 ADHESIVE DW VETROSYSTEM

E

CONSUM

er

0.5 kg/p brick

Adhesive material for fuges filling and sticking with glass bricks.

Technical characteristics DW Vetrosystem is a cement based material, sand with selected granulometry, synthetic resins and additives.

It creates a very good adhesiveness and stable in time.

Technical Data (at 23°C and 50% U.R)

Open time

≼ 35 min

Final solidifying

After 14 days

Final Data Compression srength

13 N/mm2

Flexural srength

6.5 N/mm2

Humididty resistance

Good

Application area It can be used for sticking the glass bricks on a vertical wall in interior and exterior environments.

Form

Powder

Color

White

Preservation

12 ginal packing at a dry place

Combustibility

Incombustible

Water demand

6-6.5 liter water for 25 kg DW VetroSystem

Pot life

3-4 hours

Density of fresh mortar

1.7 gr/cm3

Glass brick fitting For the application of the DW Vetrosystem in sticking the glass bricks a metallic commodity or trowel is used. The material is spread in both surfaces that will be added in such a way that the best sticking takes place. It is necessary that the glass bricks during the fitting be fit in a way that the unnecessary adhesive material comes out. After the unnecessary adhesive material comes out the fuge must be uniformed by using a wet sponge. Clean it with a clean and dry textile at the end.

Mixture pH

12

CONSUME 0.5 kg per each brick

Application temperature

+50C to +350C

Consistence

Paste

PACKING white DW Vetrosystem in sacks of 25 kg.

30

www.dast.al

01 DW YTONG

E

CONSUM ICSIII/M5

2

7-8 kg/m

Cement based adhesive material for aac blocks Technical characteristics DW Vetrosystem is a cement based material, sand with selected granulometry, synthetic resins and additives.

It creates a very good adhesiveness; light spread and good water resistance.

For interior and exterior environments.

Technical Data (at 23°C and 50% U.R)

Open time

≥ 40 min

Correction time

≥ 20 min

Final solidifying

After 14 days

FINAL DATA Compression srength to EN 12808-3

≥10 N/mm2 ≥ 2,0 N/mm2

Form

Powder

Color

Grey

Flexural srength EN 12808-3

Preservation

12 months in original packing at a dry place

Resistance in blocks detachement

≥ 1,0 N/mm2

Combustibility

Incombustible

Humidity resistance

Good

Water demand

6.5-7 liter water for 25 kg DW YTONG

CONSUME

7-8 kgm2

Pot life

4-5 hours

PACKING

GREY DW YTONG in sacks of 25 kg

Density of fresh mortar

1.6 gr/cm3

Mixture pH

≥12

Application temperature

from+5°C to +35°C

Consistence

Paste

31

01 ADHESIVE DW HOLZFIX

E

CONSUM C2 S1

3,5 to 2 5kg/m

Cement based adhesives for the welding of the ceramic tiles, monocotto, bicotto, and gres porcelain on the floor and on existing wooden walls or tiles over tiles in interior and exterior environments.

Technical characteristics Cement based adhesive, selected granulometry sand, limestone, synthetic resins and special additives.

Grey or white special adhesives containing special polymers, thixotropic, freeing resistant.

It is ideal to apply them on wooden floors subject to shaknings.

Application areas It serves for welding the natural stone tiles, ceramic tiles and porcelain tiles on the floor or walls of soft and non- absorbing surfaces. Ideal for applications on wood compositions.

Preparation of the mixture Mix 25 kg of DW Holzfix powder in 7-8liter of water by making use of an electric mixer of 500 rotations per minute until a homogenous mass is obtained. Let at rest the obtained mass for 5 minutes and mix it again before using it. The mass obtained is ready for use in about 2-3 hours.

32

The preparation of the support The support where the product will be applied must be stable and out of oils or foreign substances which may prohibit welding.

The tiles flooring For a correct application of the DW HOLZFIX, it is recommended to initially open a light adhesive layer with a free commodity. Then start applying the adhesive material with a serrated commodity appropriate for the thickness of the layer you want depending on the tile’s format and its back side configuration. In case of flooring the tiles in an exterior environment it is absolutely necessary to apply a layer of DW Holzfix at their back side in order to ensure that all the holes where water may penetrate or humidity and condensation may be caused are filled which in case of freezing it may provoke removal or breakings.

www.dast.al

01

Technical Data (at 23°C at 50% U.R ): Form

Powder

Color

Grey/white

Preservation

12 months in original packing at a dry place

Combustibility

Incombustible

Water demand

7-8 liter water for 25 kg DW Holzfix

Density of fresh mortar

1.8 gr/cm3

Mixture pH

12

Application temperature

from+5°C to +35°C

Open time

≥ 35 min

Correction time

≥ 30 min

Passing rate

After 36 hours

Pointing on walls

After 8 to 12 hours

Pointing on floors

after 24 to 48 hours

Final solidification

After 14 days

Final Data

1 Deformation rate

0

Adhesive strength on concrete ≥ 1,0 N/mm2 Adhesive strength after the ≥ 1,0 N/mm2 heating action Adhesive strength after the ≥ 1,0 N/mm2 immersion in water Adhesive strength after the ≥ 1,0 N/mm2 thaw-freezing cycles e

2

Compression strength

≥10 N/mm2

Flexibility

≤ 5 mm

PACKING White DW Holzfix in sacks of 25 kg

33

01 ADHESIVE DW MARMOFLEX

E

CONSUM C2 TE

2

3-5 kg/m

Cement based adhesive with special qualities for welding marble tiles on floors or walls in interior or exterior environments.

Technical Characteristics Cement based adhesive powder , sand of selected granulometry, limestone, synthetic resins and special additives.

Ideal for stable welding of limestone granite and natural stone tiles, on floors and walls in interior and exterior environments.

It is capable of being spread in layers up to 20mm each time and keep heavier tiles too.

No vertical slippery and long time of spreading.

It is classified as adhesive of C2TE category according to EN. Important notes Do not use it in gypsum or anhydride basements Do not use it in prefabricated concrete elements Do not use it on metallic surfaces Do not use for placing of marbles with unstable dimensions Do not use in structures subject to strong movements

34

The preparation of mixtures Mix 25kg DW MARMOFLEX with 6.5-7 litres of clean water with an electric mixer with 500 rotations per minute until a homogenous mass is obtained. The mass must be left to rest for 5 minutes and then mixed again before use.

The mass obtained this way is ready for use in 2.3 hours.

The preparation of the support Cement based floors Cement based floors must have a normal maturation of 28 days at a temperature of 23째C and U.R 50%. The supports must be flat and stable, dimensionally and mechanically resistant according to the purpose of use, free of oil remaining, oils and varnishes, wax and other material against welding. The cleaning of oils, varnishes, wax and anti adhesive materials must be realized mechanically or manually.

The supports must be dry enough: in case of humidity the adhesive material may slow down the process of solidifying.

www.dast.al

01

Technical Data (at 23°C and 50% U.R ): Form

Powder

Color

White

Preservation

12 months in the original packing at a dry place

Combustibility

Incombustible

Water demand

6.5-7 liter water for 25 kg DW Marmorflex

Density of fresh mortar

1.6 gr/cm3

Mixing pH

≥12

Application Temperatura

from+5°C to +35°C

Application thickness

up to 20 mm

Spreading time according to EN 1346

≥ 35 min

Correction time

≥ 30 min

Vertical slippery according ≤ 0.5 mm to EN 1308 Kalueshmëria

after 36 hours

1

Pointing on walls

after 8 to 12 hours

Pointing on floors

after 24 to 48 hours

Final solidifying

After 14 days

FINAL DATA

2

Adhesive strength according to EN 1348

≥1,0 N/mm2

Adhesive strength after the heating action according to EN 1348

≥1,0 N/mm2

Adhesive strength after the immersion in water EN 1348

≥1,0 N/mm2

Adhesive strength after the thaw- freezing cycles according to EN 1348

≥1,0 N/mm2

PACKING White DW Marmoflex in sacks of 25 kg

35

01 ADHESIVE DW FLEXTERIOR

E

CONSUM C2 TE

3,5 to 2 5kg/m

Preservation Combustibility Water demand

Cement based adhesive without vertical splippery for the gres porcelain ceramic tiles, natural stones and mosaics on the floor and walls especially for exterior environments.

Technical Characteristics Cement based powder like adhesive, selected granulometry sand, synthetic resins and special additives.

Adhesive with content of special polymers, thixotropic, resistant to freezing and water resistant.

Without vertical slippery and long time spreading, ideal for the upside-down tiles flooring Ideal for the ceramics tiles flooring, porcelain, natural stones and granite in floors and walls in the exterior environments.

Based on EN12004; classified as an adhesive of C2TE category.

Technical Data ( at 23°C and 50% U.R) Form Powder Color Grey/white

36

Application temperature Pot life Open time Correction time Passing rate Final solidifying FINAL DATA: Deformation rate Adhesive strength according to EN 1348 Adhesive strength of heat action according to EN 1348 Adhesive strength after the water action according to EN 1348 Adhesive strength after the thaw-freezinf cycles according to EN 1348

12 months in original packing at a dry place Incombustible 7-8 l water in 25 kg DW Flexterior from +5°C to+35°C 3-4 hours ≥ 35 min ≥ 30 min After 24 hours after 14 days

Non deformable ≥1,0 N/mm2 ≥1,0 N/mm2 ≥1,0 N/mm2

≥1,0 N/mm2

PACKING DW Flexterior grey and white in sacks of 25 kg

www.dast.al

01

EUROPEAN RATE FOR TILES ADHESIVE ORDER ACCORDING TO EN 12004 Cement-based adhesive

C1

C1T

Cement -based adhesive, without sliding ability

C1E

Cement-based adhesive, with a prolonged opening time

C1TE

Cement-based adhesive and improved characteristics

C2

Cement-based adhesive, with improved characteristics and with a fast freezing

C2T

Cement-based adhesive, with improved characteristics and with rapid freezing

C2E

Cement-based adhesive, with improved characteristics and prolonged opening time Cement-based adhesive with improved characteristics, without sliding abilities and prolonged opening time.

C2TE

C2TE S1

Cement-based adhesive, with improved characterisctics, withour sliding abilities and prolonged opening time and high flexibility

C2F

Cement-based adhesive, with improved characteristics and fast freezing

TILE ADHESIVE TABLE

DW 2000

●

●

●

DW KLEBEMORTEL 2.5

●

○

●

●

●

○

DW 3000

●

○

●

●

●

●

●

DW URBAN 40

●

●

●

●

●

●

●

DW GRANDFIX

●

FUGA COLOR

○

FUGA COLOR + DW 17

●

MEGAFUGA

●

DW 3000 + FLEXIT

●

DW 1000 + DW 17

●

●

●

●

●

●

●

●

Natural stone

Non absorbing tiles

Façade coatings

Normal surfaces

Siperfaqe normale

Pools

○

○

○

○

●

●

●

○

●

●

Glass bricks

○

○

Marble

●

○

○

○

○

VETROSYSTEM

Balcony terraces

●

DW 1100

DW MARMOFLEX

Glass bricks

Marble

Natural stone

Exterior environments Bis sized Non absorbing tiles

PRODUKTET DW 1000

Non absorbing tiles

More appropriate

Simple ceramic tiles

●

Acidi resistant adhesive materi al

Appropriate

Deformable floors

○

Tile over tile

Recommended by DAST

Heating system floors

●

Bathrooms with humidity

Interior environments

●

●

●

●

●

●

●

●

○

●

○

●

●

○

○

●

○

●

●

●

●

●

●

●

●

●

●

○

●

○

●

○

●

●

●

●

●

●

●

●

○

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

○

● ●

●

● ○

● ●

●

●

37

POOL’S SYSTEM

EXTREME adhesiveness for any project you have

â– DW URBAN 40

POOL’S SYSTEM PRODUCT

PRODUCT’S DESCRIPTION Deformable cement based adhesive of high performance, with a long time spreading and zero vertical slippery, for thicknesses of 3 to 20 mm.

Technical Characteristics - Powder based adhesive for shims (up to 15mm) with excellent workability and adaption characteristics, with zero vertical slippery.

- DW Urban 40 solidifies without decreasing the thickness with a low immersion.

- Classification according to EN12004: Category C2TE. Classification according to 12002, category S1 (elastic adhesive with a deformation rate >4.5mm) - Consume: 3-5kg/m2 - Packing: DW Urban 40 grey and white in sacks of 25 kg.

Additive for the DW line adhesives and stucco (fugacolor, megafuga) for tiles.

Description - DW17 is polymer baed mixture which improves the adhesive qualities of stucco and tiles.

- It increases the adhesive ability with the support.

- It increases the force in bending and opression.

- It improves significantly the flexibility .

- It gives a high degree of water resistance to the product.

- It improves the chemical resistance against the atmospheric agents.

- It increases the resistance to erosion and rubbing.

- DW is diluted with the water where the tiles adhesive material or stucco material will be mixed. The mixture is done at ratios of 1:1 or 1:2 in the volume.

IZOELASTIC is a cement based two –componential elastic material, very resistant to water with pressure. It serves to make the hydro isolation of surfaces in contact with water and humidity. It is appropriate for building foundations, pools, terraces etc. Cement based two componential hydro isolator , chosen aggregates, special additives and synthetic polymers in water dispersion. By mixing a two components a soft mass is obtained which can be applied in vertical surfaces too with a thickness up to 1mm for each layer. Because of the high resins component and their qualities, the product guarantees an excellent adhesiveness in all the concrete surfaces, tiles and ceramics. After the solidifying it creates a hydro isolation layer and very elastic, resistant to aggressive atmospheric agents. The product is totally hydro isolator up to a positive compression of 7 atm according to 1048. Consume: 2-4kg/m2.

POOL’S SYSTEM PRODUCT

PRODUCT’S DESCRIPTION

Fugacolor is a cement based stucco with selected granulometry and a high resistance to water. It serves to fill fuges from 0-5 mm. This product is powder based cement, natural stone powder, selected granulometry, synthetic resins, hydrophobic additives and colouring pigments. Good Workability and spreading; Classification according to EN 13888. Category CG2 Packing: Fugacolor 0-5 mm cardboard box 4x5 kg.

Megafuga cement-based stucco, with high granulometry for filling fuges from 3-20 mm. Cement-based material in powder form with natural stone powder, synthetic resins special hydrophobic additives, colouring pigments with high resistance to alkalis and detergents. Resistant to light and is able to maintain its original colour. Classification according to EN 13888. Category CG2 Packing: 4x5 kg cardboard box.

01 ADHESIVE DW URBAN 40

E

CONSUM C2 TE S1

2

3-5 kg/m

Deformable cement based adhesive of high performance, with a long time spreading and zero vertical slippery, for thicknesses of 3 to 20 mm.

Technical Characteristics Powder based adhesive for shims (up to 15mm) with excellent workability and adaption characteristics, with zero vertical slippery.

DW Urban 40 solidifies without decreasing the thickness with a low immersion.

Classification according to EN12004: Category C2TE. Classification according to 12002, category S1 (elastic adhesive with a deformation rate >4.5mm) Application area Appropriate for the ceramic tiles flooring, gres porcelain, clinker, monocotto, bicotto, and natural stone on cement based walls and floors for interior and exterior environments characterized of high humidity rate, on irregular floors ( with a shim up to 20mm). For the ceramic tiles’ flooring on balconies and terraces, for flooring of the high traffic tiles, for flooring tiles over tiles, for the flooring of tiles on fountains and pools. In order to place tiles in unstable supports it has to be reinforced with the FLEXIT additive.

42

Elasticizing In order to floor tiles on the unstable surfaces , as a result of shrinkage and inflation or vibrations e.g. the prefabricated concrete plates, gypsum tiles or wood surfaces, metallic surfaces etc. It is appropriate that 25 kg tiles’ adhesive DW URBAN 40 be elasticized by adding 5-6kg Flexit ( read the technical data FLEXIT page 119) and the quantity of water according to the workability requirements.

The support preparation Cement based supports Traditional cement based supports must have a maturation time of 28 days at a temperature of 23°C and U.R.40%.

The support where the product will be applied must be clean, out of foreign substances such as paints, oils, varnishes, anti adhesive materials etc. The cleaning is done manually or mechanically. The support must be sprayed with water before applying the adhesive material in a such a way that it gives time to the frying period.

Flooring the tiles For a correct application of the DW Urban 40 initially apply a light layer of the adhesive with a slightly serrated comb and then apply the adhesive material with an appropriate serrated commodity for the required thickness of the layer, for the rigidity of the support and for the type of the tile that will be floored. After flooring the tile suppress it carefully in such a way that its back side be totally wetted. Special weather conditions such as strong wind, high temperatures or high water absorbing supports may significantly reduce the spreading and correction time in some minutes. In order to make this problem slight it is

www.dast.al

01

recommended to wet the support before applying the adhesive material. Check whether the adhesive material has formed a membrane before flooring the tile. In such a case spread again the adhesive in order to reactivate its adhesive power. Avoid totally the contact of water with the adhesive material which has formed a membrane as this may form an anti adhesive layer. In the outer walls and floors, especially in the cases when the back side of the tile is very much structured or is a clinker tile, terracotta etc. spread the adhesive material. At the same time in order to avoid the cavities at the back side of the tile, where water can penetrate or humidity may condensate, as this may cause the removal or breaking at freezing time.

Technical Data (at +23°C and 50% U.R.): Form

Powder

Color

Grey/white 12 months in a original packing at a dry place Incombustible 7.5-8 liter water for 25 kg DW Urban 40

Preservation Combustibility Water demond

1

2

Density of fresh mortar

1.6 gr/cm3

pH mixture

12

Application temperature

+50C to +350C

Open time

≥ 40 min

Correction time

≥ 30 min

Passing rate

after 24 hours

Pointing on walls

After 8 to 12 hours

Pointing on floors

after 24 to 36 hours

Final solidifying

14 days

final data

3

Deformation rate

High

Adhesive strength

≥ 1,9 N/mm2

Adhesive strength after the heat≥ 1,5 N/mm2 ing action Adhesive strength after immer≥ 2,1 N/ mm2 sion in water Adhesive strength after the ≥ 2,2 N/ mm2 thaw-freezing cycles Compression strength

≥ 15 N/mm2

Flexibility

≤ 5 mm

Packing DW Urban 40 grey and white in sacks of 25 kg

43

THERMO ISOLATION SYSTEM Energy saving, protection form moisture

■ CONEXION 77 ■ CONEXION 99

THERMO ISOLATION SYSTEM PRODUCT

PRODUCT’S DESCRIPTION

DW Conexion 77 serves for welding all the types of panels usually used for the realization of theromo isolating systems capote, such as polystyrene, polyurethane, graffiti, mineral fibers in brick walls, concrete or cement based mortar. DW Conexion 77 is a grey material prepared , of Portland cement based of high quality, carbonic sand stone of a selected granulametry, synthetic resins and special additives which improve the workability, adhesiveness in difficult surfaces and grow the level of the hydrophobicity of reinforced mortar against rain.

DW Conexion 99 serves for welding and then for flattening all the types of panels usually used for the realization of capote thermo isolating systems, such as polystyrene, polyurethane, stone wool, glass wool, graffiti, mineral fibers in brick walls, concrete or cement based mortar. DW Conexion 99 is a grey or white material prepared, of Portland cement based of high quality, carbonic sand stone of a selected granulometry, synthetic resins and special additives which improve the workability, adhesiveness in difficult surfaces and increase the level of the hydrophobic of reinforced mortar against rain. DW Conexion 99 is ideal for exterior facades and for interior environments. The flattening of the panels must be done two times by combining them putting the glass- fibers- based nets resistant against alkaline.

It is characterized of very good spreading and workability, very high coverage. It facilitates the application on exterior and interior surfaces filled with mortar and prepared traditional mortar.

Appropriate for the realization of the refinishes of the surfaces filled with traditional mortar or cement-limestone based prepared mortar. It can be covered in paint or with other mineral and synthetic nature coatings.

Liquid material of white colour, incombustible used to treat the flat surfaces which will alter be painted with paint or coated decoratively. It is used for interior and exterior environments. It can be easily applied with a roller or brush. It creates a very good isolation and connection of the treated surfaces with the decorative layer.

Tecnofix Liquid reduces significantly the absorbing ability of surfaces to water.

Before the final product is applied on the support wait for at least 12 hours for Tecnofix Liquid to get dry. It is packed in buckets of 5k and 20 kg.

Decorative coating made of marble sand, resistant to atmospheric agents of very good hydro isolation abilities. Because of the new formula it does not allow the dust and dirt to stay on wall by getting self cleaned very easy.

It allows the walls penetrability of vapour by forming a stable structure. It is characterized of a very good workability and spreading. The product is easy to apply.

THERMO ISOLATION SYSTEM PRODUCT

PRODUCT’S DESCRIPTION

The thermo isolation panels of this system have polysterene components. The polysterene, solid material in the form of foam is of EPS-F model (expanded polystyrene), 17-25 kg/mÂł, incombustible.

This type of polysterene can be easily carved by profiting very quick the desired shape and it offers optimum cost compared to the cost of other isolations.

They are necessary to fix the polysterene with the support. Their size must be 5 cm more than the thickness of the thermo isolation panel .

The UPA used in the thermo isolation system are of 2 types.

- Plastic UPA - Metallic UPA

The mesh is made of glass fibers; it is incombustible and provides connection between the adhesive material and thermo isolation panel for a maximal stability in the thermo isolation system. It is advisable that the optimum net for this system be 145gr/m2 or 160gr/m2 with a size of 4*4.5mm.

Schematic presentation of the thermo isolation system

Thermo isolation system Support: plaster, brick, concrete, stone Adhesives : Conexion 77 &Conexion 99 Polisterol: EPS-F Upa: plastic or metallic Adhesives: Conexion 77 & Conexion 99 glass fiber nets

Tecnofix liquid

Decortex Fino Classic

01 ADHESIVE DW CONEXION 77

E

CONSUM C2 S1

3.5 - 42 kg/m

Powder type adhesive material reinforced in fibers for the realization of the thermo isolation ETICS DW Conexion 77 serves for welding all the types of panels usually used for the realization of theromo isolating systems capote, such as polystyrene, polyurethane, graffiti, mineral fibers in brick walls, concrete or cement based mortar. DW Conexion 77 is a grey material prepared , of Portland cement based of high quality, carbonic sand stone of a selected granulametry, synthetic resins and special additives which improve the workability, adhesiveness in difficult surfaces and grow the level of the hydrophobicity of reinforced mortar against rain.

The preparation of the surfaces The supports must be compact, seasoned, without broken oils, paints or removing parts. It is to verify that bricks be sewn well and do not have parts that can break. If there is, remove these parts and repair the mortar surface. The walls coated with grout should be scratched to verify if the surface below it is painted with old paints not well welded or detachable parts. Dusty surfaces should be treated with TECNOFIX liner LIQUID. The superficial cracks can be caulked with DW Conexion 77, whereas the deep structural cracks must be treated in a way to eliminate the causes and not repeat them again. In case when the surface is not totally flat or straight it is to flatten it or straighten it by using Tecnofix.

48

Welding (sticking) It is necessary to fix metal profiles leveled holder before you start soldering the panels, in order to have a more regular placement. For applications on irregular surfaces, such as unplastered brick wall, the adhesive material is applied by trowel locating it as a line bar on the sides of the panel and some points in its center (or forming an X in the center of the panel) with shims in order to compensate the disparities. For applications in flat surface is advisable to open the adhesive throughout the surface of the panel via a serrated commodity (from 8 to 10 mm). It is to take care that the covered surface from the adhesive material be at least 40% of the total surface of the panel.

The panels should be put horizontally upside-down. It is to be careful in joining the panels in a way that no empty space or disparity is left. Then it is proceed with the mechanical fixation with upa (for usual panels 50x100 cm it is recommended to have 8 sticking points for a square meter).

www.dast.al

01

TECHNICAL DATA (AT 23 C AND 50% U.R) 0

Form

Powder

Color

Grey

Granulometry

≤ 0.7 mm

Water demand

23%(± 1%)

Mixture ph

>12

Pot life

4 hours

Application temperature

+50C to +350C

Consume for mm thickness

1.4 kg/m2

Preservation

12 months in original packing in a dry place

FINAL DATA Humidity resistance rate

Good

Time resistance

Good

Deformation rate

Average

Adhesive strength after immer≥ 1.0N/mm2 sion in water

1

2

Adhesive strength after heat ac≥ 1.0N/mm2 tion Adhesive strength in concrete

≥ 2,0 N/mm2

Compression strength

≥ 9,0 N/mm2

Flexibility

≤ 5 mm

Flexural resistance

≥ 4,0 N/mm2

The data are at a temperature of (23 ±20C) and (50 ±5)% relative humidity. Lower temperatures prolong the maturation and solidifying time.

3.5 - 4 kg/m2 for application in points.

4 – 5 kg/m2 for application with a serrated commodity.

Packing In sacks with a weight of 25 kg in pallets of 1200kg.

3

49

01 ADHESIVE DW CONEXION 99

E

CONSUM C2 S1

2

/m

3,4-5 kg

Powder type adhesive material reinforced in fibers for the realization of the thermo isolation ETICS DW Conexion 99 serves for welding and then for flattening all the types of panels usually used for the realization of capote thermo isolating systems, such as polystyrene, polyurethane, stone wool, glass wool, graffiti, mineral fibers in brick walls, concrete or cement based mortar. DW Conexion 99 is a grey or white material prepared, of Portland cement based of high quality, carbonic sand stone of a selected granulometry, synthetic resins and special additives which improve the workability, adhesiveness in difficult surfaces and increase the level of the hydrophobicity of reinforced mortar against rain. DW Conexion 99 is ideal for exterior facades and for interior environments.

The flattening of the panels must be done two times by combining them putting the glass- fibers- based nets resistant against alkaline.

The preparation of the surfaces The supports must be compact, seasoned and stable, without broken oils, paints or removable parts. It is to verify that bricks be sewn well and do not have parts that can break.

If there is, remove these parts and repair the surface with mortar. The walls coated with grout should be scratched to verify if the surface below it is painted with old paints not well welded or detachable parts. Dusty surfaces should

50

be treated with primer TECNOFIX. The superficial cracks can be caulked with DW Conexion 99, whereas the deep structural cracks must be treated in a way to eliminate the causes and not repeat them again.

Welding (sticking) It is necessary to fix metal profiles leveled holder before you start soldering the panels, in order to have a more regular placement. For applications on irregular surfaces, such as unplastered brick wall, the adhesive material is applied by a trowel locating it as a line bar on the sides of the panel and some points in its center (or forming an X in the center of the panel) with shims in order to compensate the disparities. For applications in flat surface is advisable to open the adhesive throughout the surface of the panel via a serrated commodity (from 8 to 10 mm). It is to take care that the covered surface from the adhesive material be at least 40% of the total surface of the panel.

The panels should be put horizontally upside-down. It is to be careful in joining the panels in a way that no empty space or disparity is left. Then it is to proceed with the mechanical fixation with upa (for usual panels 50x100 cm it is recommended to have 8 sticking points for a square meter).

www.dast.al

01

TECHNICAL DATA (AT 23 C AND 50% U.R) 0

Form

Powder

Color

Grey/white

Specific weight

1.4kg/dm3

Granulometry

≤ 1-1.2mm

technical characteristics Water demand

23% (± 1%)

Mixture pH

>12

Pot life

4 hours

Application temperature

50C to350C

Consume for mm thickness

1.4 kg/m2

final data: Humidity Resistance

Very good

Time resistance

Very good

Deformation

Average

1

2

Adhesive strength on concrete

≥ 2 N/mm2

Adhesive strength after the action of heat

≥ 1,0 N/mm2

Adhesive strength after the immersion in water

≥ 1,0 N/mm2

Compression strength

≥ 12 N/mm2

Flexural strength

≥ 7 N/mm2

Flexibility

≤ 5 mm

The data are at a temperature of (23 ±20C) and (50 ±5)% relative humidity. Lower temperatures prolong the maturation and solidifying time.

As adhesive 3.5 deri 4 kg/m2 for application in points.

4 – 5 kg/m2 for application with a serrated commodity.

As a leveller 1.4 kg/m2 per mm applied shims

3

Packing In sacks with a weight of 25 kg in pallets, euro palets of 1200kg.

51

GROUTS FOR JOINTS

â– FUGACOLOR

â–

Cement based grouts for joints with selected granulometry and high stability against water; it serves for filling the joints from 0 to 5 mm.

Cement based grouts, with selected granulometry and high stability against water; it serves for filling the joints from 3 to 20 mm.

MEGAFUGA

02 GROUTS FOR JOINTS FUGACOLOR 0-5

E

CONSUM CG2

2

/m

0.2-1 kg

Cement based grouts for joints with selected granulometry and high stability against water; it serves for filling the joints from 0 to 5 mm.

Technical Characteristics Cement based material in the form of powder, with a natural stone powder with a selected granulometry, synthetic resins, hydrophobic additives and coloring pigments.

• Very good workability and spreading • It can be easily cleaned • It leaves a polished surface at the end.

• Waterproof material • High resistance to bases (alkalis) and detergents • Resistant to erosion (corrosion) • Resistant to UV rays.

• It prevents the efflorescent process.

• Available in 24 colors.

• According to the classification EN 13888, belonging to the category CG2.

Area of use Fugacolor 0-5 mm can be used in these cases as follows: Fuges caulking between porous ceramic tiles, monocotto, bicotto, gres porcelain and natural stone with a space of 0-5mm.

For the floor’s caulking and exterior coatings, when an

54

increase of the impenetrability , elasticity and mechanical power, for vibration surfaces, for surfaces with shrinkage and inflation (terraces, heating system floors, pools, fountains etc), stucco Fugacolor must be reinforced with 500gr additive DW 17 diluted with 700-1000 ml water for an amount of 5 kg Fugacolor.

Important notes Do not use it for fuges bigger than those recommended.

Application Method By using Fugacolor 0-5mm the space between tiles can be easily filled by using a rubber trowel. The removal of the remaining mass must be done with a wet sponge at the moment when the Fugacolor has achieved stability, the required consistency (a consistency which are achieved in 1020 minutes after the application of the Fugacolor 0-5mm).

The final cleaning of the tiles is done with a dry textile. The final cleaning can be done even after a day when the material is somehow solidified, and in this case an appropriate textile is chosen for cleaning.

TECHNICAL DATA AT 230C AND 50% U.R Form Powder Color

24 colors (see the table of colors)

Preservation

12 months in original packing at a dry place

Combustibility

Incombustibile

Water demand Consistency of mixture

1-1.5 L for 5 kg Fugacolor 7-7.5 L for 25 Fugacolor Fluid and liquid mixture www.dast.al

02 Density of mixture

2 gr/cm

Mixture pH

12

Pot life

2 hours

Applicaition temperature

+50C to +350C

3

TABLE OF FUGACOLOR AND MEGAFUGA 04 Grey 10 Cement grey

Final data Stability to humidity

Good

05 Light grey

Stability to solvents and fats

Good

Stability to acids

Good

Compression strength

≥ 25 N/mm2

Flexural strength

≥ 8 N/mm2

15 Manhattan grey 03 Pearl grey 02 Black

Passing rate

after 24 hours

Pointing on walls

After 8 to 12 hours

Pointing on floors

After 24 to 36 hours

Fuges cleaning

after 10 – 15 minutes

01 White 09 Bahama beige 12 Caramel

Final data with the DW 17 Resistance Humidity

Very good

Ewsistance to solvents and fats

Very good

Resistance to acids

Very good

Compression strength

≥ 32 N/mm2

Flexural strength

≥ 15 N/mm2

Absorbing (water absorbing) after 4 hours according to(EN 13888)

< 0.2 g/m2

35 Anemone 16 Light ohrid colour 14 Cotto 06 Light brown 20 Maroon 08 Brown

coverage Tiles size (cm)

31 Ceramic

Fuges width 2 mm

3 mm

2 x 2 x 0,3

1.3

1.5

10 x 10 x 0,6

0.4

0.6

15 x 15 x 0,7

0.3

0.45

20 x 20 x 0,7

0.24

0.35

0.48

0.58

20 x 30 x 0,7

0.2

0.3

0.4

0.48

30 x 30 x 0,8

0.19

0.28

0.26

0.45

Packing Fugacolor 0-5 mm cardboard box 4*5 kg Fugacolor 0-5 mm cardboard box 10*2 kg

4 mm

5 mm

07 Red brown

0.8

1

34 Mint

0.62

0.77

32 Cypress 19 Krokus 30 Mykonos blue 36 Violet 17 Red 33 E verdhë

55

02 GROUTS FOR JOINTS MEGAFUGA 3-20

E

CONSUM CG2

2

/m

0.2-2 kg

Cement based grouts, with selected granulometry and high stability against water; it serves for filling the joints from 3 to 20 mm Technical Characteristics Cement based powder like material, natural stone powder, synthetic resins, special hydrophobic additives , colouring pigments with high resistant to alkali and detergents. It is resistant to light and it has the ability to preserve its original colour. Based on the classification EN 13888 it belongs to the CG2 class.

It is characterized of: Very good workability and spreading Easy to clean It provides a smooth surface Water resistant High resistance to bases (alkali) and detergents Resistant to erosion Resistant to UV rays It prevents the process of fluorescence Available in 24 colours Specifications Stuccos used for filling the fuges on the floor and walls with the size of 3-20mm must be plastered with resistant to water cement based Megafuga type fillers (with an absorbing of water less than 2 according to the rate EN 13888).

56

Field of Use Megafuga 3-20 mm is used in the following cases: Fugeâ&#x20AC;&#x2122;s plastering between porous ceramic tiles, monocotto, bicotto, gres porcelain and natural stone at a space of 3-20mm. For the plastering of the floors and the exterior coatings when an increase of the impenetrability, elasticity and mechanical force, for surfaces with vibration, for surfaces with inflation and shrinkage ( terraces, heated floors, pools, fountains etc). Stucco Megafuga must be reinforced with 500 gr. Additive DW17 diluted with 700-1000ml water for a package of 5kg Fugacolor.

Important Notes It must not be used for the filling of the fuges bigger than those recommended.

Recommendations Not recommended to plaster floors or walls whose supports are still wet, because a wet surface can cause the formation fluorescence in fuges. This is stimulated from the migration of the soluble salts from inside to the surface, which brings a non homogenous spreading in the

www.dast.al

colour of the fuges. The phenomena of the fluorescence can be present in cases when the floors of the basements storeys are not well isolated. In such cases spots or small cracks are formed in the filler’s colours. Be careful regarding the water to use in the mixture even a small tolerance enables the phenomena of fluorescence and changes in the colour of the stucco.

02

Method of preparation Pour 1-1.5 L water and 5kg of Megafuga. Mix with an electric mixer of a small number of rotations until a homogenous mass is obtained. It is recommended that the mass be left in peace for about 5 minutes and mix again before applying the product.

When reinforcing the Fugacolor with the additive DW 17, initially dilute 500 gr DW17 in a container of 700-1000ml water and then pour the Fugacolor powder which we mix it the same way as above.

Technical Data (at 230C and 50% U.R) Form

Granular powder

Color

See colour table, available in 24 colours

Preservation

12 months in an original packing at a dry place

Combustibility

Incombustible

Water demand

1-1,5 liter water for 5 kg Megafuga 3-20 mm

Mixture density

2 gr/cm3

Mixture pH

12

Consistence

Liquid paste

Application temperature

+50C to +350C

Pot life

2 hours

Passing rate

After 24 hours

Pointing on walls

After 8 to 12 hours

Pointing on floors

After 24 to 36 hours

Final Data Resistance to humidity

Very good

Resistance to solvents and oils

Very good

Compression strength

≥ 30 N/mm2

Flexural strength

≥ 10 N/mm2

Grouts preparation The surface covered in tiles and the space between them must be totally clean before applying the product. If the tile’s flooring has been done with an adhesive, the fuges fillings on walls must be done after 4-8 hours. Fuge’s fillings on floors must be done after 24-36 hours. If the tile’s flooring is done with traditional mortar, it is recommended that on walls it should be done after 2-3 days, fuge’s fillings on the floor is recommended to be done after 8-10 days.

Method of Application Spaces between tiles can be easily covered with Megafuga 3-20mm by using a rubber spatula. It is recommended to use a container out of which we can pour the thin prepared stucco without the need to misuse it when filling fuges over than 5mm on the floors.

Removing the remaining mass with a wet sponge at the moment that Megafuga has achieved the required stability which is obtained10-15 minutes after the product’s application.

Packing cardboard box 4*5kg

57

MORTARS ■ FIBREN GP-70 ■ YTONG PUTZ+ ■ MORTAR FOR PLASTERING ■ MORTAR FOR MASONRY ■ GIPSPUTZ

03 MORTARS FIBREN GP-70

EN 1504-3

Multifunctional material Description FIBREN GP-70 is a cement based product, hydraulic limestone, specific additives and synthetic fibber which are used to make the mortar more solidified and maximal resistance. This product is used as an attaching material for the preparation of traditional mortar, facades restoration and damaged colon’s fixing. Its characteristics allow the usage in preparatory machineries and mortar pumping. It is a product appropriate fore interior and exterior environments. It is recommended to work at temperatures between +5°C up to +35°C.

In the case of direct usage mix it with water with an electric mixer with slow rotations (200-300 rot/min) until a homogenous mass is formed. Then the mixture is left 5 minutes to rest and after a final mixture it is ready to use.

In the case when it is used as an attaching material for the traditional mortar it is necessary to mix it with river sand or with carbonate sand. For this purpose it is necessary that 1 m3 sand be mixed with 10 sacks of FIBREN GP-70.

Method of usage It is an easy to use product. It can have a direct usage when we doing repairs and filling damaged concrete colons as well as when it is used for facades’ restorations.

When using it as an attaching material for the preparation of the traditional mortar mix it with sand.

60

www.dast.al

03

Technical Data (at 23 C and 50% U.R) 0

Form

Powder

Color

Grey

Preservation

12 months from the production date

Consistence

Liquid paste

Workability time

60 min

Thickness when it is used 3-4 mm as a colon resotorator Density of fresh mortar

2,2 g/cm3

Water amount

According to the purpose of usage

1

Final data Adhesive strength after 28 days

≥ 3.5 N/mm2

Compression strength After 7 days

≥ 65 N/mm2

After 28 days

≥ 95 N/mm2

Flexural strength

2

After 7 days

≥ 10 N/mm2

After 28 days

≥ 15 N/mm2

3

61

03 MORTARS YTONG PUTZ +

E

CONSUM EN 998-1

2

/m

13-18 kg

Foundation mortar for plastering for walls with bricks Mixture preparation Mix 25kg of plastering mortar powder by using a commodAAC in interior and exterior environments. ity or mechanically with a chopper. When the product is applied with a chopper be careful for the mixture consistTechnical characteristics: Cement based powder material , llimestone, carbonic ency and do not mix it with other materials. Protect the stone sand with selected granulometry, synthetic resins bricks and mortar (especially during the work interruption) from rain. and special additives.

Very good workability Vertical appearance Very good adhesiveness on walls Application Area • It can be used with a machinery or manually for plas tering the walls with AAC blocks in interior and exterior environments.

• The product can be applied with a machinery or manu ally. During the product’s application the temperature of the support and the environmental temperature must not be from +5°C to +35°C. • The support preparation • The support where the material will be applied must be dry, clean, consistent, absorbing, stable. It must not have foreign remaining such as oils, varnishes, petrol etc.

62

www.dast.al

03 Techincal Data (at 230C and 50% U.R) Form

Powder

Color

Grey

Preservation

12 months in original packing at a dry place

Combustibility

Incombustible

Water demand

6.5-7litre water for 25kg for masonry mortar

Density of fresh mortar

1.9 gr/cm3

Consistence

Tyxotopic

Application temperature

from +50C to +350C

Pot life

3-4 hours

Workability time

30 min

Maximum thickness for a layer

1 cm

Solidifying start

385 min

1 Final Data Flexural strength

â&#x2030;Ľ 2 N/mm2

Compression strength

â&#x2030;Ľ 12 N/mm2

Resistance to salts

Good

PACKING YTONG PUTZ+ 25 kg

2

63

03 MORTARS MORTAR FOR PLASTERING

E

CONSUM

2

EN 998-1

15 kg/m

per 1 cm s thicknes

Foundation filling material for brick or block wall for interior or exterior environment.

Technical Characteristics Cement, limestone, stone sand based powder material with selected granulometry, synthetic resins and special additives.

It is characterized of a very good workability High mechanical resistance Without vertical slippery Adhesive ability in walls and ceilings Application Area It can be used as basic mortar for plastering all kinds of supports such as brick walls, blocks etc. The product is applied with a machinery or by hand. During the application of the product the temperature of the support of the environment must not be from +5°C up to +35°C. Preparation of the Support The support where the product will be applied must be dry, clean, consistent, absorbing, stable. It must not have foreign remaining such as oils, varnishes, petrol etc. The support where the material will be applied must not have such phenomena like fluorescence.

64

The preparation of the mixture Mix 25kg of Filling Mortar powder with 6.5-7liter of water through an electric mixer or manually, until there is obtained a mass for the required workability. It can be elaborated with a pump.

Product’s Application Method The product is applied manually, with a trowel or mechanically with a pump. When the product is applied with a pump it is to take care about the elaboration consistency.

Do not mix with other materials except of Latex. In cases of longer pauses, the mixer must left empty and clean. The fresh mortar must be elaborated within 2 hours. Protect the mortar and bricks (especially during the interruption of the work) from rain. In case of high temperatures it is recommended that the mortar be wet before it is dried so that it does not lose water.

Reinforcement with Latex The mortar can be reinforced with the additive Latex in order to improve the adhesiveness, impenetrability, elasticity, mechaninal force etc. The mixing raito is 1:5 in water. (see the technical data LATEX page 120.)

www.dast.al

03

Technical Data (at 23 C and 50% U.R) 0

Form

Powder

Color

Grey

Preservation

12 months in an original packing at a dry place

Combustibility

Incombustible

Water demand

6-6.5 liter water for 25 kg for masonry mortar

Density of fresh mortar

1.9 gr/cm3

Mixture consistency

Tyxotopic

Application temperature

+50C to +350C

Pot life

3-4 hours

Workability time

30 min

Maximum thickness for each application

1.5 cm

Compression resistance 7 days

? ≥ 3.5 N/mm2

Thermo transmission according to EN 1745

0,28 W/mK

1

Solidifying start

385 min

Compression resistance 7-days

≥ 3.5 N/mm2

Compression resistance 28 -days

≥ 12 N/mm2

Resistance to salts

Good

Consume 15 kg/m2 for cm thickness Packing

Mortar for plastering in sacks of 25 kg in silos

2

65

03 MORTARS MORTAR FOR MASONRY

E

CONSUM EN 998-1

200-2530 kg/m

Material for bricks adhesiveness of bricks on wall in interior and exterior environments Technical Characteristics Cement based adhesive material in powder form, limestone, sand stone, with big selected granulometry, synthetic resins and special additive.

It is characterized of a very good workability Easily applicable and workable.

It creates a very good adhesion with the support.

Application Area It is used for the adhesion of bricks and blocks on walls in all the types of the supports. The product is applied with a machinery and by hand. During the application the temperature of the support and the environments’ temperature must be from +5°C up to +35°C. The preparation of the support The support where the material is applied must be dry, clean, consistent, absorbing, stable. It must not have foreign remaining such as oils, varnishes etc. It is not allowed to apply the product on a frozen support ( frozen bricks).

66

When the support (bricks) are dry and characterized of an ability of high water absorbing in such cases it is suggested to spray the support with water before applying the product.

The preparation of the mixture Mix 25kg by pouring it in water manually or mechanically, until there creates a mass with the required workability.

Product’s Application Method The product is applied manually with a commodity mechanically with a machinery. When the product is applied with a machinery take care about the consistency do not mix it with other materials. It is suggested the control of the consistency of the mortar elaboration for each filling of the crane bucket. In case of long pauses, the mixer must be left empty and clean. The fresh mortar must be elaborated within 2 hours. Protect the bricks and mortar (especially during work interruption) from rain.

www.dast.al

03

Technical Data (at 23 C and 50% U.R) 0

Form

Powder

Color

Grey

Preservation

12 months in original packing at a dry place

Combustibility

Incombustible

Water demand

6-6.5 liter water for 25 kg masonry mortar

Density of fresh mortar

1.85 gr/cm3

Application temperature

+50C up to +350C

Duration of the mixture

3-4 hours

Workability time

30 min

1 Final Data Compression strength

â&#x2030;Ľ 15 N/mm2

Flexural strength

â&#x2030;Ľ 3.5 N/mm2

Packing Mortar for masonry in sacks of 25 kg and in silos.

2

67

03 MORTARS GIPSPUTZ

E

CONSUM 2

EN 13279

13 kg/m

per 1 cm s thicknes

Gypsum based basic filling mortar with polymers and special additives containing for brick or block walls for interior environments.

Technical Characteristics It a powder like, gypsum based material, hydrated limestone, selected granulometry , synthetic resins and special additives for application in interior environments.

Without vertical slippery Very good workability Very good adhesiveness for walls and ceilings High mechanical resistance In conformation with EN 998-1 Application area It can be used with a pump or by hand as a basic mortar for the brick or block wallâ&#x20AC;&#x2122;s plastering for interior environments. It enables at the same time the realization of fillings and refinishes without the need for a second application.

mix again before use. The mixture can be done through a pump which applies the product.

The Supportâ&#x20AC;&#x2122;s Preparation The support where the product will be applied must be leveled and out of foreign substances such as fats, varnishes, paints etc.

Method of Application The product is applied manually with a commodity or mechanically by making use of a pump. When the product is applied by making use of a pump it is to be careful with the consistency of the processing. Do not mix it with other materials.

The Preparation of the Mixture Mix 25kg Gipsputz with 7-8liter water by making use of an electric mixer with a low number of rotations until a homogenous mass is obtained. It is recommended that the obtained mass be left to rest for about 10 minutes and

68

www.dast.al

03

Technical Data (at 23 C and 50% U.R) 0

Form

Powder

Color

White

Preservation

12 months in original pasking at a dry place

Density of fresh mortar

1000 kg/m3

Thermalconduction according to EN 1745

0,28 W/mK

Flexion resistance according to EN 1015-11

4,0 N/mm2

Processing time

130 min after pouring the mortar

Waiting time for filling

max 20 min

Environment and surface Temperature

Voer +50C to +350C

Average thickness

12 mm

Minimal thickness

7 mm

Application Area It can be used with a pump or by hand as a basic mortar for the plastering of brick or block walls for interior environments It enables at the same time the realization of fillings and refinishes without the need for a second application.

The support must be treated with Gips Primer.

Packing: Gipsputz in saks of 25kg and in sillos.

69

REFINISHES

■ FINO CLASSIC ■ BONIFIN

■ ACRYL SPACHTEL ■ SPATORELLA

■ SPATORELLA GIPS

04 REFINISHES FINO CLASSIC

E

CONSUM EN 998-1

2

/m

2-2.5 kg

It is a powder form material produced based on HTT technology (Hörman Transpirance Tecnology) which prevents the creation of moisture and it allows the cement based wall transpiration, hydrated limestone, carbonate stone sand and selected granulometry marble, sysnthetic resins and special additives.

Technical Characteristics It is characterized of very good spreading and workability, very high coverage (10-12m2 / 25kg sack).

It facilitates the application on exterior and interior surfaces filled with mortar and prepared traditional mortar.

Applicable up to a thickness of 3mm.

Application area Appropriate for the realization of the refinishes of the surfaces filled with traditional mortar or cement-limestone based prepared mortar. It can be covered in paint or with other mineral and synthetic nature coatings.

Important Data Do not add other components such as cement, limestone etc in the given product.

Do not apply it on surfaces which have been previously painted.

Do not apply on plastic surfaces or coatings.

Do not apply it on surfaces thicker that 3mm.

72

Do not add water after the composition is prepared.

Apply it at a temperature from +5°c to +35°C. Do not apply it at places with ceramic coating.

Do not apply it on gypsum based surfaces.

Do not apply it on easily breakable or destroyed surfaces.

The preparation of the support The surface or support where the FINO CLASSIC will be put must be leveled and stable. Unleveled surfaces of more than 3mm must be leveled before applying the product.

Preparation Method of the Mixture Pout 7.5-8 liter of water and 25kg Fino Classic in a container. Mix them with an electric mixer at slow rotations until the mass becomes homogenous. In order to stimulate the mixture characteristics and in order to have a best result it is recommended to leave the mixture at rest for 10 minutes and mix it again before usage.

Product’s method of Application The material must be spread with a metallic commodity by ensuring thus a uniform layer in the whole surface. The second application of the material must be applied 30 minutes after the first application.

After obtaining the necessary evaporation for about 15 minutes at temperature of 23 °C the surface must be rubbed with a sand paper. The environment temperature significantly affects at the time of product’s workability.

The lower the temperature the longer the duration time of the workability.

Cleaning method Hands and tools must be cleaned until the product is still liquid. www.dast.al

04

Technical Data (at 23 C and 50% U.R) 0

Water demand

7. 5-8liter water for white/grey 25 kg Fino

Pot life

3-4 hours

Application temperature

from +50C to +350C

Mixture pH

12

Application’s thickness

2 mm

Waiting time for the second application

30-40 min

Waiting time until the rubbing period

15-20 min

Waiting time for the surface painting

3-4 weeks

Form

Powder

Color

Grey/white

Preservation

12 months in original packing at a dry place

Combustibility

Incombustible

1

2

FINAL DATA Compression strength after 28 days

≥ 5 Nmm2

Flexural strength after 28 days

≥ 2.5 Nmm2

consume

1.2 kg/m2 for 1 mm thickness

Packing

Fino Classic Grey and White in sacks of 25 kg

3

73

04 REFINISHES BONIFIN

E

CONSUM EN 998-1

2

/m

2.5-3 kg

Material in powder form based on cement, hydrated lime, carbonate sand with selected granulometry, synthetic resins and special additives.

Technical Characteristics It is characterized of openness and very good workability which facilitates the application on the outer and interior surface filled with both traditional mortar and prepared mortar.

It is applicable in a thickness up to 3mm.

Areas of application It is suitable for the implementation of ceiling finishes of surfaces filled with traditional stucco or mortar prepared with lime-cement base. It can be covered in paint or other mineral or synthetic based covers.

Important data It is prohibited to add other components such as cement, lime etc in the given product.

It must not be applied in surfaces which have been painted before.

It must not be applied in plastic surfaces or covers.

It must not be applied in surfaces with a disparity of more than 3mm.

74

Water must not be added after the content is prepared.

The application temperature must be +5°C to +35°C. It must not be applied in surfaces which are covered in ceramics.

It must not be applied in gypsum-based surfaces.

It must not be applied in fragile or destroyed surfaces.

Preparation of the support The surface or the support where the grout will be placed must be leveled and stable. Surfaces with a thickness of more than 3mm must be leveled before applying the product.

Mixing preparation method Pour 7.5-8 liters of water in a container and 25kg of BONIFIN. Mix it with an electric mixture with a slow number of rotations until it becomes homogenous. It is recommended that the mixture be left in serenity for about 10 minutes and before using mix it once again in order to stimulate the mixing characteristics and have the best possible results.

Product application method The material must be spread with a metallic commodity thus enabling a uniform layer all over the surface. The second application must be applied 30 minutes after the first one. When it is dried in 15 minutes time at a temperature of 23°C the surface must be rubbed with a trowel. The environment temperature significantly affects the time of workability of the product. The lower the temperature is, the longer the workability time is.

www.dast.al

04

Technical data(in +23°C and 50% U.R.) Water demand

7. 5-8 liter of waters for 25 kg BONIFIN

Pot Life

2-3 hours

Application Temperature

+50C to +350C

pH of mixture

12

Thickness for layer

2mm

Time for second layer

30-40 min

Waiting time to rubbing

15-20 min

Waiting time for the surface painting

3-4 weeks

Form

Powder

Color

Grey/white

Preservation

12 months in original packing

Combustibility

Incombustible

1

Final Results Compressive strength after 28 days

≥ 3 Nmm2

Flexture strength after 28 days

≥ 1.5 Nmm2

Consume Packing

1.5 kg/ m2 for 1 mm thickness Grey and white in sacks of 25 kg

2

3

75

04 REFINISHES ACRYL SPACHTEL

E

CONSUM EN 998-1

2

1 kg/m

Stucco based on nanotechnology applications to realize smooth ceiling finishes in exterior and interior environments. technical characteristics Stucco consisting of white cement, hydrated lime, white marble powder, resin and special additives.

Based on nanotechnology application Used in interior and exterior environments It is possible that it gets a thickness of 0-3 mm anytime it is applied It is easily scoured with a sandpaper and provides a ceiling finishes strong and highly polished It is in conformity with the rate EN 998-1

The preparation of the support The supports which are characterized of the elevation of more than 3mm must be leveled in advance before applying the putty.

Product’s application method Product spreads on the surface through a smooth spatula to ensure a spread and complete coverage of the surface.

The product is applied two times with a thickness of 3mm.

The second time is applied after the surface is dried in 2-3 hours after the first application at a temperature of 23°C. Product Cleaning Work tools and hands’ cleaning should be done when the product is completely dried.

Application areas For the stucco of walls and ceilings filled with traditional mortar or mortar prepared with lime-based cement.

For the stucco of the concrete surfaces.

For the creation of the polished smooth finishes in interior and exterior environments.

76

www.dast.al

04

Technical data (in +23째C and 50% U.R.)

Form

Powder

Color

White

Preservation

12 months in original packing in a dry place

Combustibility

Incombustible

Water Demand

4.5-5 liters water for 15 kg Acryl Spachtel

Pot Life

4-5 hours

pH of mixing

12

Temperature of application

+50C to +350C

Maximal thickness for 1 mm layer Time for second layer

after 60-90 min

Standby for rubbing

24 hours

Standby for painting

3-4 weeks

1

Consume

1kg/ m2

Packing

Acryl spachtel white in sacks of 15 kg

2

3

77

04 REFINISHES SPATORELLA

E

CONSUM EN 998-1

2

1 kg/m

Plastering Stucco for realizing smooth ceiling finishes.

Technical features Plastering stucco consisting of white cement, hydrated lime, white marble powder, resins and special additives.

Characterized by a workability and easy opening and without vertical slippery which facilitates application through vertical surface.

Used for interior and exterior environments Allows a thickness of 1 to 3 mm for each hand. easily scoured with sandpaper and gives a smooth ceiling finishes.

It is in conformity with EN 998-1 rate Scope of use For walls plastering and ceilings filled with traditional mortar or mortar prepared with lime-based cement.

Concrete surfaces plastering.

Plastering of gypsum card walls and ceilings.

Important notes Do not add other components such as cement or lime in a given product.

Do not apply the product on painted surfaces.

Do not apply the product on supports coated with plastic.

Should not be applied in a thickness greater than 5 mm.

78

Do not add water to the composition after it has been prepared.

Should be applied at temperatures from +50 C to +350 C Reinforcement with LATEX To improve adhesiveness ,water resistant, plasticity, elasticity, mechanical strength, etc..the spatula can be reinforced with the additive LATEX. Mixing ratio is 1:5 in water. (see technical tab latex fq.120) Mixture Preparation Mix 15 kg putty plaster with 4.5-5 litre of water with electrical mixing with a small number of rotations until you get a homogeneous mass.

It is recommended that the obtained mass be left in peace for about 5 minutes and mix again before use.

The preparation of the Support The supports characterized of a interchanges bigger than 3mm must be levelled in advance before applying the stucco. The support where the product will be applied must be free of foreign materials such as fats, varnishes, paints etc. The support must be wet with water before applying the product.

www.dast.al

04

Product’s Application Method Spread the product on a surface with a smooth spatula to provide a complete spreading and covering of the surface.

The product is applied up to a thickness of 3 mm from one to two applications.

Cleaning The cleaning of the working tools and hands must be done during the time when the product is totally dried.

Technical Data (at 230C and 50% U.R) Form

Powder

Color

White

Preservation

12 months in original packing at a dry place

Combustibility

Incombustible

Water demand

4.5-5 litre water for 15 kg Spaturela

Powder density

1.6 gr/cm3

Mixture pH

12

1

2

3

Pot life

3-4 hours

Temperature of application

+50C to +350C

Maximum thicknes for a layer

1mm

Waiting time for the application of the second layer

After 60-90 min

Waiting time for rubbing

24 hours

Waiting time for painting

3-4 weeks

Final Data Compression strength after 28 days

≥ 4,5 N/mm2

Flexural strength after 28 days

≥ 1,7 N/mm2

Adhesive strength in concrete

≥ 0,5 N/mm2

Consume

1 kg/ m2 per mm thicknes

Packing

Spatorella sacks of 15 kg

79

04 REFINISHES SPATORELLA GIPS

E

CONSUM EN 998-1

2

0.3 kg/m

Stucco which serves for fuges fillings between the panels of gypsum card.

Technical Characteristics Gypsum based stucco, composed of hydrated limestone, marble powder with selected granulometry and special additives.

Gypsum based stucco which is used with the covering bars for the plastering of fuges between gypsum card tiles, for the plastering of fuges and cracking with unfinished concrete surfaces with or without porosity.

It is used for the realization of the refinishes in gypsum based supports and gypsum panels.

It is characterized of a very good workability, easy spreading and non-slippery, which makes easier the application in vertical surfaces.

For interior environments.

It can be very easily ribbed with sand paper.

In conformity with EN 132791

80

Technical Data (at 230C and 50% U.R) Form

Powder

Color

White

Preservation

12 months in original packing at a dry place

Combustibility

Incombustible

Water demand

7.5-8 liter water for 25 kg Spatorella Gips

Pot life

1.5-2 hours

Mixture pH

12

Application temperature

from +50C to+350C

Maximum thickness in a layer

1 mm

Waiting time for rubbing

After 24 hours

Waiting time for painting

After 3-4 weeks

www.dast.al

04 Final Data Compression strength according to EN 1015-11

≥ 3,5 N/mm2

Flexural strength according to EN 1015-11

≥ 1.9 N/mm2

Adhesive strength in gypsum according to EN 1015-12

≥ 0.5 N/mm2

1

Application Area It is used together with covering bars for the plastering of fuges between gypsum card tiles, for the plastering of cracking with finished concrete surfaces.

Plastering of concrete surfaces with or without porosity.

PACKING Spatorella Gypsum in sacks of 15kg and 5 kg.

2

81

DECORATIVE COATINGS

■ GRAFIATO ACRYL ■ DECORTEX

■ GRAFIATO ■ DECORTEX MINERAL

05 DECORATIVE COATINGS GRAFIATO ACRYL

EN 998-1

Decorating coating ready for use serving for the treatment of the facades and interior surfaces It an ecologically tested product. Produced based on the HTT technology (Hörman Transpirant Tecnology) which enables the wall’s ventilation and preventing the mold.

Because of the formula containing synthetic fibers and special additives. This product does not allow the cracking and does not allow the dirtiniess to unify with it, thus it gets self cleaned.

General characteristics It allows the penetrability of vapor in walls.

It forms a stable structure It closes the cracking of the cement-limestone plastering It shapes a beautiful and protective structure against the atmospheric agents.

It is characterized of a very good workability and spreading It is characterized of a long working time In conformity with EN998-1 Easy to apply product Application Area The support where GRAFIATO ACRYL will be applied must be cleaned in advance from dust as well the oil, petrol remaining, varnishes, wax and anti adhesive materials. The

84

cleaning of oils, varnishes, wax or anti adhesive materials is realized mechanically or manually. Before applying GRAFIATO ACRYL the support must be flattened and leveled Tecnofix. The supports must be flat and mechanically stable according to the purpose of use.

Product’s application method The product is ready for use. The application of the product may be realized manually by making use of a trowel. Immediately after applying the product on the support, it has to be flattened with a plastic commodity and work on it horizontally, vertically or circular according to the aesthetic effect one desires. The workability depends on the absorbing ability of the support as well as on the environment temperature.

Important Data Be careful that the environment temperature is not higher that +5°C during the application of the product.

The product after application must be sprayed with water in order to avoid water loss when there are high temperatures.

Avoid contacting the product with the face while applying www.dast.al

05

the product. The product is classified as irritating while in contact with the face.

Consume Structure

Consume Granular structure 1.5 mm 2.5 kg/m Line structure 2.0 mm 2.8 kg/m Line Structure 3.2 mm 3.9 kg/m Technical Data (at 230C and 50% U.R) Form

Paste

Color

White

Preservation

12 months in original packing at a dry place

Combustibility

Incombustible

Humidity resistance

Good

Mixture pH

12

Application Temperature

+50C to +350C

The structure it creates

1.5 mm full 2 mm with lines 3.2 mm with lines

Workability time

20 min at 200C

1

Density

1,85 kg/lit

Compression strenght

≥ 8,0 N/mm2

Flexural strenght

≥ 3,5 N/mm2

Adhesive strenght

≥ 1,0 N/mm2

Packing Grafiato Acryl plastic buckett 25 kg

2

3

85

05 DECORATIVE COATINGS DECORTEX

Decoration coating for interior and exterior Decorative coating used for the treatment of facades and interior surfaces.

It is an ecologically product. It is produced based on the HTT technology (Hรถrman Transpirant Tecnology) which enables the wall ventilation and prevents mold. This product does not allow cracks and does not allow dirt unify with it thus it is easy to clean.

Decortex has the following characteristics: It realizes a complete water isolation in conformity with Din 18550 Allows the permeability of the wall against vapor.

It forms a stable structure.

It closes the cement-limestone based plaster cracking.

It shapes a beautiful and protective structure against atmospheric agents.

It is characterized of a very good spreading and workability.

It characterized of a long period of work (it does not dry easily).

It is suitable for a thickness of 1.5mm, 2mm, 3.2mm.

It is an easy to apply product.

Areas of application The product is suitable for the decorative coating creation

86

of very good waterproofing, adhesive and elastic qualities.

It can be used for the creation of decoration coating in surfaces filled with cement mortar or basic thermo isolation mortar which are previously flattened with Tecnofx or Conexion 77 or 99 in the systems of thermo isolation after having been treated with Tecnofix Liquid.

The preparation of the support The support where Decortex will be applied must be clean of dusts and oil remaining, oils and varnishes, wax and anti-adhesive materials. The cleaning of the oils, varnishes, wax or the anti-adhesive materials is done mechanically or manually. Before applying the Decortex the support must be leveled with the dry liner Tecnofix. The supports must be flat and mechanically stable .

The method of mixture preparation The product is mixed until a homogenous easy to apply mass is formed. The mixture may be done with an electric mixer with a slow number of rotations. It is necessary that the mixture be totally clean of any pigment remaining in order to avoid any change in the product obtained. The product application can be done manually by using a commodity and is worked in horizontal, vertical or circular direction according to the aesthetic effect which is aimed to achieve.

The workability depends on the environment temperature. www.dast.al

05 Important Data During the application note that the environment temperature be higher than 5°C. While applying the product it is to be careful and avoid the face contact with the product.

The product is classified as irritating when in contact with one’s face.

STRUCTURE CONSUME Granular structure 1.5mm 2.4kg/m Lining structure 2.0mm 2.8kg/m Lining structure 3.2mm 3.9 kg/m Technical Data (at 230C and 50% U.R) Form

Paste

Color

White

Preservation

12 months in original packing in a dry place

Combustibility

Incombustible

Humidity resistance

Good

pH of mixture

12

Application Temperature

+50C to +350C

Structure

1.5 mm complete 2 mm in stripes 3.2 mm in stripes

Open Time

20 min at 200C

Density

1,85 kg/lit

Compression Strength

≥ 10 N/mm2

Flexibility Strength

≥ 5,0 N/mm2

Adhesive Strength

≥ 1,0 N/mm2

Packing Decortex plastic bucket 25 kg

87

05 DECORATIVE COATINGS GRAFIATO

EN 998-1

Decorating coating for interior and exterior usage It is a white cement, marble stones with selected granulomtry, synthetic resins and hydrophobic powder based material. Decorating material for interior and exterior usage.

GRAFIATO is characterized of the following qualities: • It realizes a full isolation against water in conformity with Din 18550 • It allows the penetrability of vapor in walls.

• It forms a stable structure • It closes the cracking of the cement-limestone plastering • It shapes a beautiful and protective structure against the atmospheric agents.

• It is characterized of a very good workability and spreading • It is characterized of a long working time (does not dry) • Appropriate for a thickness of 1mm, 2mm, 3mm.

• Easy to apply product Application Area It is appropriate for the creation of the decorative coating with very good hydro isolation qualities, adhesive and elastic. It is used for the creation of the decorative coating on surfaces filled with cement mortar and basic thermo isolation mortar which are flattened in advance with Tecnofix or

88

Conexion 77 & 99 in the thermo isolation systems after it is treated with Tecnofix Liquid.

The Support Preparation The support where GRAFIATO will be applied must be in advance cleaned and out of dust as well as out of petrol, oil, varnishes, wax and other anti adhesive materials. The cleaning of petrol, oil, varnishes, wax and other anti adhesive materials is realized mechanically or manually. Before applying GRAFIATO the support must be flattened and leveled with Tecnofix. The supports must be flat and mechanically stable according to the purpose of use.

Method of applying the product The product in the form of powder is mixed with clean water until a homogenous mass is formed and it is easily applicable. The mixture can be done with an electric mixer with slow rotations, it is to take that the mixer be totally clean of different pigment remaining in order to prevent any change in the formed product. The application of the product can be done manually by using a commodity. Immediately after the application of the product on the support which is flattened with a plastic commodity and worked horizontally, vertically or circular according to the aesthetic effect one wants. The workability depends on the absorbing ability of the support as well as on the environment temperature. www.dast.al

05

Important Data During the application of the product it is to take care that the temperature of the environment be higher that 5°C. in the case of the high temperatures the product after the application must be sprayed with water in order to avoid water loss.

During the application of the product be careful in avoiding the face contact with the product. It is classified as an irritating product when in contact with the face.

CONSUME Grafiato 1mm covers up to 12 m2 Grafiato 2mm covers up to 8 m2 Grafiato 3mm covers up to 7 m2 TECHNICAL DATA Form

Powder

Color

White

Preservation

12months in original packing at a dry place

Combustibility

Incombustible

Water demand

7-8 liter water for 25 kg

1

Humidity resistance

Good

Mixture pH

12

Application temperature

+50C to +350C

The structure it creates

1 mm complete 2 mm with lines 3 mm with lines

2

Workability time

20 min at 200 C

Density of fresh mortar

1,85 kg/lit

Density of dry mortar

1,6 kg/lit

Compression Strength

≥ 7,0 N/mm2

Flexibility Strength

≥ 2,5 N/mm2

Adhesive Strength

≥ 1,0 N/mm2

Packing Grafiato 1.0, 2.0, 3.0 in sacks of 25 kg

3

89

05 DECORATIVE COATINGS DECORTEX MINERAL

EN 998-1

DECORTEX MINERAL HTT TEC Decorative coating used for the treatment of facades and interior surfaces.

It is an ecologically product. It is produced based on the HTT technology (HĂśrman Transpirant Tecnology) which enables the wall ventilation and prevents mold. Thanks to its new formula and special additives this product does not allow the dust and dirt thus it is easy to clean.

Decortex has the following characteristics: High elasticity and good adhesiveness with the sub layer.

Allows the permeability of the wall against moisture.

The workability time is long.

It forms a stable structure.

It closes the cement-limestone based plaster cracking.

It shapes a beautiful and protective structure against atmospheric agents.

It is characterized of a very good spreading and workability.

It characterized of a long period of work.

It is in conformity with EN 988-1.

It is an easy to apply product.

Areas of application The product is suitable for the decorative coating creation

90

of very good waterproofing, adhesive and elastic qualities.

It can be used for the creation of decoration coating in surfaces filled with cement mortar or basic thermo isolation mortar which are previously flattened with Tecnofx or Conexion 77 or 99 in the systems of thermo isolation after having been treated with Tecnofix Liquid.

Preparation of the support The support where Decortex will be applied must be clean of dusts and oil remaining, oils and varnishes, wax and anti-adhesive materials. The cleaning of the oils, varnishes, wax or the anti-adhesive materials is done mechanically or manually. Before applying the Decortex the support must be leveled with the dry liner Tecnofix. The supports must be flat and mechanically stable according to the purpose of use.

Method of mixture preparation Pour 7.5-8 liters of water in a container and 25kg Decortex. Mix it with an electric mixer with a small number of rotations until the mass becomes homogenous. It is recommended that the mixture be left in serenity for about 10 minutes and before using mix it once again in order to stimulate the mixing characteristics and have the best possible results.

Product application method The product is ready to use. The productâ&#x20AC;&#x2122;s application can be done manually by making use of a commodity. Immewww.dast.al

05

diately after the product’s application in the support its flattening is done by a plastic commodity and is worked in horizontal, vertical or circular direction according to the aesthetic effect which is aimed to achieve. The workability depends on the support’s absorbing ability as well as on the environment temperature.

Important Data During the application of the product it is take care that the environment temperature be between +5°C to 35°C. In case of high temperature presence the product must be sprayed in water in order to avoid water loss.

While applying the product it is necessary to be careful to avoid the face contact with the product. This product is classified as irritating in case of having a contact with one’s face.

CONSUME Decortex Decortex Decortex

1mm covers up to 12 m2.

2mm covers up to 8 m2 3.2mm covers up to 6 m2.

1

2

Technical Data Form

Powder

Color

White

Preservation

12 months in original packing in a dry place.

Combustibility

Incombustible

Water Demand

7-8 liter of water per 25 kg

Humidity Resistance

Very good

Mixture pH

12

Application Temperature

+50C to +350C

Structure

1 mm complete 2 mm stripped 3,2 mm stripped

3

Open time

30 min in 200 C

Density of fresh mortar

1,85 kg/lit

Density of dried mortar

1,6 kg/lit

Pressure Strength

≥9,0 N/mm2

Flexibility Strength

≥3,5 N/mm2

Adhesive Strength

≥1,0 N/mm2

Packing Decortex mineral in 25 kg sacks.

91

WATERPROOF COATINGS

■ IZOELASTIC LIQUID ■ DW IZOL

■ IZOBAND ■ IZOELASTIC

■ IZOFLEX ■ MONOFLEX

■ IZOTRATE ■ MONOLIT

06 WATERPROOF COATINGS IZOELASTIC LIQUID

E

CONSUM

0.8-1 2 kg / m

Elastomeric Hydro isolator Description IZOELASTIC LIQUID is a hydro isolator painting material for terraces, composed of high elastomeric resins.

It offers a high hydro isolation and elasticizing.

It is characterized of very good adhesive abilities in all cement based surfaces as well as those made of wood or metal bricks and over any other hydro isolation material.

Usage possibility on unleveled layers.

It provides high elasticizing by avoiding the creation of the cracking which may take place with time.

The white color of the hydro isolator during summer helps lowering the temperature. It is hermetic but it allows the penetrability from the vapor.

Application Area IZOELASTIC LIQUID is used as a hydro isolator in terraces, balconies, walls, and at places with humidity.

It is easily applied by creating thus a hydro isolation membrane with a high elasticity and mechanical resistance without causing cracking or shrinkage. It is easily applicable in difficult angles, joints of different materials which create fuges etc. IZOELASTIC LIQUID is not recommended to be used for the hydro isolation of underground basements.

94

Technical Data Type: acrylic polymer in dispersion Viscosity: 20000 ¹ 2000 mPa.s 23°C Density: 1,25-1,30 kg/lit Stretching up to the dettachment + 500% Hidroisolation 7 ATM according DcIN 1048 Application Method/ Consume The surface where the material will be applied must be clean of dust, oils etc. in order to obtain a very good hydro isolation it is recommended that the surface be hydro isolated with IZOELASTIC LIQUID be treated in advance with the liner HIDROPRIMER (consume 200-300 g/m2).

Apply IZOELASTIC LIQUID two times with a brush or a roller, after the applied liner is dried totally in advance on the surface to be hydro isolized. The consume is aproximately 0.8-1kg/ m2 depending on the surface to be hydro isolated.

The second application must be applied only after the liner is totally dried. Pay attention that the second application is done in a cross shape over the first application. The places which are characterized of cracking it is recommended that the hydro isolator be reinforced from the net application with glass fibers with a density of 65-125g, which is applied immediately after the first application of the hydro isolators. Then apply over the net in one or two applicawww.dast.al

06

tions of other hydro isolators.

In the cases when the surface that will be hydro isolated is characterized of common cracking it is recommended that the glass fiber net be applied in the whole surface which will be hydro isolated. In this case of consume of IZOELASTIC LIQUID is 1.5-2kg /m2 . make sure that the net placed on the surface which will be hydro isolated must not create shrinkage but be put correctly over the surface.

Local Isolation of the Cracking Apply the liner HIDRO PRIMER in the damaged surface and at a radius of 10 cm along the cracking. Apply the first application of IZOELASTIC LIQUID after the liner is dried by adding then the reinforcing glass fiber net. Then over a net apply two other times IZOELASTIC LIQUID.

1 PACKING IZOELASTIC LIQUID is packed in plastic buckets of 4kg and 20 kg.

WARNING! It is recommended that the product be protected of freezing and exposure to the sun. The temperature during the application must be from +5°C up to +30°C.

Trajtimi me HYDRO PRIMER

2

3

Vendosja e bandave elastike nëpër kënde.

350C 50 C

95

06 WATERPROOF COATINGS DW IZOL

E

CONSUM

2

1kg/m

Waterproofing elastic liquid

Description DW IZOL is a ready for use product which can be applied with brush or roller. After drying it forms a very elastic membrane which is not penetrable from water and it allows its vaporisation.

Area of application DW IZOl is ideal for the hydro isolation of surfaces, such as balconies, bathrooms, etc before flooring the ceramic tiles.

It is appropriate for all floor or wall surfaces constructed with concrete, gypsum tiles etc. This product may be applied in all the surfaces where there is water pressure.

Technical Data Color Density Viscosity Minimal application temperature Drying time Time of moving Hydro isolation Setting the tiles adhesive

Grey 1.58 Kg/Lit 50 000 mPa.s

Method of use The support must be clean, out of grease, dust or oils.

The broken parts must be mended before application. The support is to be treated with Hidro Primer with a mass of about 200-300 g/m2 depending on the absorbing capability of the support, before applying the DW IZOL. Application DW IZOL is applied by making use of a brush or roller in two layers after the layer of HYDRO PRIMER is totally dried. The second layer must be applied after the first layer is dried. The hydro isolating membrane of DW IZOL must be reinforced in the corners of the floor and in the spaces of the fuges by using a net of 65 g/m2 fibreglass type. The working tools must be cleaned while the DW IZOL is still not dried. The ceramic tiles flooring must be done by using an adhesive with elastic qualities or by using FLEXIT as an elasticizer for the adhesive material.

Preservation 18 months from the day of production in preserved in the original packing and protected of freezing and direct exposure to the sun.

+ 5oC 6 hours to 20oC after 6 hours at 20oC 7 ATM according to DIN 1048 After about 6 hours 20oC

350C

96

50C

www.dast.al

06 PRODUCT

PRODUCT’S DISCRIPTIONS

IZOBAND S10 Isolation bar for corners formed from the wall and the floor

IZOBAND EX 90 Hydro isolation element to cover the corners of the wall

IZOBAND IN 90 Isolation bar for corners formed from the wall and the floor

TABLE OF WATERPROOF COATINGS

●

●

● ● ●

●

●

●

○

IZOELASTIC LIQUID IZOFLEX DW IZOL MONOFLEX

IZOTRATE

○

●

●

●

○

○

●

● ● ●

●

○

○

○

MONOLIT

IZOBAND

● ● ●

Wall surfaces

●

Objetc foundations

●

Pools, fountains

●

Balconies

IZOELASTIC

Terraces in use

PRODUKTET

Terraces not in use

More appropriate

Floors and walls which absorb humidity from froundations

●

Basements

Appropriate

Exterior environments

Water reservoirs

○

Interior environments

Tile over tile

Recommended by DAST

Bathroms and environments with humidity

●

○

○ ○ ○

○

○

● ●

○

○

○

○

○

○ 97

06 WATERPROOF COATINGS IZOELASTIC

E

CONSUM EN 1504-2

2

2-4 kg/m

Cement based two componential elastic material, highly resistant against the positive and negative pressure of the water. It serves for the creation of the hydro isolation of surfaces in common contact with water and humidity. It is appropriate for building foundations, pools, terraces etc.

Technical Characteristics Cement based two componential hydro isolator of chosen aggregates, special additives and synthetic polymers in water dispersion. By mixing two components, a soft mass which can be applied in vertical surfaces is obtained with a thickness of up to 2mm for a layer. Because of the high containing of the synthetic resins and their qualities, the product guarantees an excellent adhesiveness in all the concrete, brick and ceramic (unprepared) surfaces. After the solidifying it creates a hydro isolating and flexible layer, resistant to the aggressive atmospheric agents. The product is totally hydro isolator up to a positive compression of 1.5 atm.

Application Area The hydro isolation membranes flooring before placing the tiles for interior and exterior environments.

Flexible protection and water and humidity resistance for concrete surfaces and plasters.

Hydro isolation coatings and concrete surface protection,

98

subject to chemical aggression, as anti freezing salts, sulphate etc.

Flexible and hydro isolating leveling of the cracked plasters.

The bigger the water pressure the thicker the application of the product must be.

Flexible leveling of the concrete structures with thin sections, subject to damages because of weighs (eg. Prefabricated structures) Hydro isolation of pools with matured concrete ( over 6 months) Important notes Use Izoband bar in fuges between floors and walls.

Use Izoband bar for the hydro isolation of wide fuges.

Do not apply IZOELASTIC for the repairing with big thickness (over 2mm for each layer).

Do not apply IZOELAST at temperatures lower than +5째C or bigger than +30째C. Do not mix IZOELASTIC with other materials (cement, aggregates or water).

Protect it from rain or accidental water during the first 2428 hours after the application.

In the cases when it is applied on the existing floors and walls coated in ceramics, clinker, terracotta etc. make sure that the tiles be fixed good in the support and clean of fats, wax, oils or paints which may reduce the adhesive power.

The supports which will be hydro isolated must have appropriate inclination.

On terraces and big roofs built with materials which preserve argyle or plastics define discharge points positioned according to the present humidity (every 20 m2).

The surface which will be treated must be totally clean and stable: use water pump for the cleaning with pressure.

www.dast.al

06

Area of Application The material’s application can be done with a brush or a roller in some applications depending on the protection from water to be provided. The material must be applied 1mm for each layer. The following layer is applied after the first layer is applied. After applying the material protect it from high temperatures, rain etc. IZOELASTIC needs a reinforcement my covering the surfaces with a net bar with fibers 10 cm the joining corners between the walls and floors or in surfaces with a lot of oppression and micro cracking etc. and in case the surface has a lot of damages that it will be covered totally with a glass fiber net from 65125 gr/m2 . The net can be used for pools or terraces too.

Technical Data (at 23°C and 50% U.R) A

B

Form

Powder

Liquid

Color

Grey

White

Volumme mass

1.5 gr/cm3

1.1 gr/cm3

Dry remaining

100%

25%

Combustibility

Incombustible

The color of the mixture

Grey

Mixture ratio

2,5

Method of application

Paintable with a brush

Working time

≥ 90 min

Volume mass of the mixture

1.7 gr/ cm3

Application temperature

from +80C to +300C

Maximal thickness for each application

1 mm

Time between applications

4-5 hours

Time for tile’s flooring

24 hours

Preservation

12 months

1

The placing of tiles on the izoelastic membrane In terraces: after the application of IZOELASTIC wait for at least 24 hours for the maturation ( under best conditions).

Put the tiles by using DW KLEBEMORTEL 2.5 ose DW 3000. Fill the fuges with Fugacolor 0-5. The wide fuges must be filled with MEGAFUGA 3-20. It would be good to reinforce Fugacolor or MEGAFUGA with DW. In pools: after the application of IZOELASTIC wait 2 days for maturation (at best conditions). Install the ceramic tiles by using DW URBAN 40. Fill the fuges with MEGAFUGA 3-20 or reinforced FUGA-COLOR 0-5 with DW 17. The pool may be filled 28 days after the tiles’ flooring.

Foundatoins: the foundation holes can be filled minimum 4

days after the applicaiotn of IZOELASTIC. FINAL DATA Adhesive strength in concrete After 7 days +230C and 50% U.R

≥ 1,0 N/mm2

After 28 days + 230C and 50% U.R

≥ 1,5 N/mm2

Stretching

> 40%

Resistance in positive pressure

7 atm according DIN 1048

Resistance in negative pressure

≥ 4 atm according DIN 1048

Penetrability

Impenetrable

PACKING IZOELASTIC (A+B), in sacks of 25 Kg bottles of 10 kg.

300C 80C

99

06 WATERPROOF COATINGS IZOFLEX

E

CONSUM EN 1504-2

2

2-4 kg/m

Hydro isolated Cement based two componential material, elastic with protection function for pools, terraces, foundations and basements.

Technical Characteristics Cement based two componential hydro isolators, selected granulometry solid materials, and synthetic polymers in water dispersion. By mixing two components a mass that can be applied even in vertical surfaces can be obtained, with a thickness up to 1mm for a layer.

Technical Characteristics Cement based two componential hydro isolator of chosen aggregates, special additives and synthetic polymers in water dispersion. By mixing two components, a soft mass which can be applied in vertical surfaces is obtained with a thickness of up to 1mm for a layer. Because of the high containing of the synthetic resins and their qualities, the product guarantees an excellent adhesiveness in all the concrete, brick and ceramic (unprepared) surfaces. After the solidifying it creates a hydro isolating and flexible layer, resistant to atmospheric agents.

Application Area The hydro isolation membranes flooring before placing the tiles for interior and exterior environments.

Flexible protection and water and humidity resistance for concrete surfaces and plasters.

100

Hydro isolation coatings and concrete surface protection, subject to chemical aggression, as anti freezing salts, sulphate etc.

Elastic and hydro isolating leveling of the cracked plasters.

The bigger the water pressure, the thicker the application of the product must be.

Flexible leveling of the concrete structures with thin sections, subject to damages because of weighs (eg. Prefabricated structures) Appropriate for the hydro isolation of surfaces subject to vibrations and different deformations.

Hydro isolation of pools with matured concrete ( over 6 months) Important notes Use Izoband bar in fuges between floors and walls.

Use Izoband bar for the hydro isolation of wide fuges.

Do not apply IZOELASTIC for the repairing with big thickness (over 1mm for each layer).

Do not apply IZOELAST at temperatures lower than +5째C or bigger than +30째C. Do not mix IZOELASTIC with other materials (cement, aggregates or water).

Protect it from rain or accidental water during the first 2428 hours after the application.

During the hot season avoid exposing the material (powder and liquid) to the sun before use.

In the cases when it is applied on the existing floors and walls coated in ceramics, clinker, terracotta etc. make sure that the tiles be fixed good in the support and clean of fats, wax, oils or paints which may reduce the adhesive power.

The supports which will be hydro isolated must have appropriate inclination. www.dast.al

06

On terraces and big roofs built with materials which preserve argyle or plastics define discharge points positioned according to the present humidity (every 20 m2).

The surface which will be treated must be totally clean and stable: use pressure water pump or just rubber for the cleaning.

Area of Application The material’s application can be done with a brush or a roller in some applications depending on the protection from water to be provided. The material must be applied 1mm for each layer. The following layer is applied after the first layer is applied. After applying the material protect it from high temperatures, rain etc. IZOFLEX needs a reinforcement my covering the surfaces with a net bar with fibers 10 cm the joining corners between the walls and floors or in surfaces with a lot of oppression and micro cracking etc. and in case the surface has a lot of damages that it will be covered totally with a glass fiber net from 65-125 gr/ m2 . The net can be used for pools or terraces too.

Rules about implementation after application After the application under high temperatures or strong winds it is recommended to protect the surface from the vapor by using a wet cover.

Technical Data (at 23°C and 50% U.R) A

B

Form

Powder

Liquid

Color

Grey

White

Volumme mass

1.5 gr/cm3

1.1 gr/cm3

Dry remaining

100%

25%

Combustibility

Incombustible

The color of the mixture

Grey

Mixture ratio

3.1kg

Method of application

Paintable with a brush

Working time

≥ 75 min

Volume mass of the mixture

1.7 gr/ cm

Application temperature

from +80C to +300C

Maximal thickness for each application

1 mm

Time between applications

4-5 hours

Time for tile’s flooring

24 hours

Preservation

12 months

1kg

The placing of tiles on the izoelastic membrane In terraces: after the application of IZOFLEX wait for at least 24 hours for the maturation ( under best conditions).

Put the tiles by using DW KLEBEMORTEL 2.5 ose DW 3000. Fill the fuges with Fugacolor 0-5. The wide fuges must be filled with MEGAFUGA 3-20. It would be good to reinforce Fugacolor or MEGAFUGA with DW 17.

In pools: after the application of IZOflex wait 2 days for maturation (at best conditions). Install the ceramic tiles by using DW URBAN 40. Fill the fuges with MEGAFUGA 3-20 or reinforced FUGA-COLOR 0-5 with DW 17. The pool may be filled 28 days after the tiles’ flooring.

Foundatoins: the foundation holes can be filled minimum 4 days after the applicaiotn of IZOEFLEX. FINAL DATA Adhesive strength in concrete

3

After 7 days +230C and 50% U.R

0,7 N/mm2

After 28 days + 230C and 50% ≥ 1,0 N/mm2 U.R Stretching > 20% 7 atm according DIN Resistance in positive pressure 1048 ≥ 4 atm according Resistance in negative pressure DIN 1048 Penetrability Impenetrable Packing IZOFLEX (A+B), in sacks of 25 Kg bottles of 8 kg.

IZOFLEX (A+B), in sacks of 13 Kg and bottles of 4 kg.

300C

80C

101

06 WATERPROOF COATINGS MONOFLEX

E

CONSUM EN 1504-2

2

2-3 kg/m

Flexible hydro isolator material mono componential with good hydro isolation and protective abilities.

Technical Characteristics Mono componential cement based powder material with selected granulometry, synthetic resins and special additives with hydrophobic qualities. The material can be mixed with water by forming a liquid and homogenous mixture.

It is easily applicable with a spatula or brush. It has good adhesive abilities because of the high number of the resins it s has.

Important Data Do not use for the hydro isolation of the plastic surfaces, wooden, plasterboard or painted walls.

Do not add other components such as cement, limestone etc. in the mixture.

Do not apply in surfaces which have stagnant water.

Do not use the product to solve interior condensation problems . use the respective product for this.

Reinforce the product with the additive FLEXIT in case you want a bigger elasticity.

Application Field Laying the hydro isolation membranes before applying the interior and exterior tiles. Use it for the hydro isolation of the interior and exterior underground walls, water tanks,

102

toilets, terraces, balconies and fountains. Flexible protection and resistant to water and humidity for the concrete surfaces and plasters. Hydro isolation and elastic levelling for the cracked plasters.

Mixture of the Preparation The material is mixed with an amount of water depending on the application form. If the hydro isolator is applied with a spatula one must mix 6-7liter. In case the product is applied with a brush mix 7-8liter water for each 25kg of the product. Mix the composition with a mixer with slow rotations until a homogenous composition is formed. The mixture is left 10 minutes to rest. It is recommended to mix the composition before use.

Preparation of the Support Cement floors in balconies, terraces, toilets etc.

The surface to be isolated must have an appropriate inclination and must not have cavities (cavities must be covered with Filling Mortar to reinforce with additive LATEX after wetting with water). If there are wire or steel remaining which come out from the depth of the concrete or wall then they must be cut at a depth of 2-4 cm and then cover the hole as described above. The surface to be treated www.dast.al

06

must be totally clean, resistant and stable. Wet the surface of the work before treating it with MONOFLEX. For the isolation of basements in old buildings, remove any existing plastering up to a height of 30 cm over the level of the humidity and then proceed as above. It is recommended to reinforce the mortar of the plastering with the additive LATEX. It is recommended to reinforce with LATEX wherever there is necessity to make a flat surface.

Productâ&#x20AC;&#x2122;s Application Method The hydro isolator is applied with a spatula or a brush depending on the thickness of the surface to be hydro isolated. The application with the spatula is done 2-3 times but it is important that when it is applied the first time be left for 5-6 hours depending on the environment temperature. It is important that the first layer be totally dry before applying the other layers of the hydro isolator. Pay attention to the first layer of the application of the hydro isolator by making possible that it is covered carefully all the surface to be hydro isolated.

Final Data

Technical Data

Adhesive strength in concrete

â&#x2030;Ľ1,0 N/mm2

Resistance to humidity

Very good

Incombustible

Resistance to amortization

Very good

12 months in original packing at a dry place

Penetrability

Impenetrable

Form

Powder

Color

Grey

Mixture density

1.30 gr/cm3

Combustibility Preservation

PACKING

Water demond With spatula

6-7 L water for 25 kg Monoflex

With brush

7-8 L water for 25 kg Monoflex

Mixture pH

12

Pot life

3-4 hours

Application time between two layers

After 4 hours at 23 0 C

max thickness per layer

1 mm

Resistace in positive pressure

7 atm according to DIN 1048

Monoflex in sacks of 25 kg

300C 80C

103

06 WATERPROOF COATINGS MONOLIT

E

CONSUM EN 1504-2

2

3-4kg/m

Description Mono componential hydro isolator cement based mortar which offers good isolating qualities to humidity and protects the concrete from carbonizing. It is appropriate to use for the hydro isolation of the water deposits, basements.

Easy to apply and low application cost and it does not have irritating effect for the reinforced concrete in steel.

Application Area The hydro isolation from humidity of the concrete surfaces and walls. Appropriate for the hydro isolation of the water deposits, basements, underground environments etc. appropriate for the interior hydro isolation for the underground areas such as basements as it resists to high pressure because of the very strong connection it creates with the support.

olit will be applied, initially close them and then apply the product.

If there are wires in the surface where the product will be applied they must be cut from 2 to 4 cm and after closing the hole created apply the product.

Application Ad gradually MONOLIT in the required water amount at a continuous mixture until an appropriate viscose mass to apply with a brush is created. The surface where the product will be applied must be totally dry and there should be no humidity. There are applied two or more layers of the product depending on the environment where it will be applied. Each layer must not be more than 1mm thick in order to avoid the cracking and the following layer is applied after the previous is totally dry.

Preparation Method The surface must be clean, out of dust fats and any other dirt.

If there is cracking or breakings in the surface where Mon-

104

www.dast.al

06

Technical Data Form

Powder

Color

Grey

Mixture density

1.30 gr/cm3

Combustibility

Incombustible

Water demand With a spatula

6-7 L water for 25 kg Monolit

With a brush

7-8 L water for 25 kg Monolit

Mixture pH

12

Pot life

3-4 hours

Application time between 2 layers

after 4 hours at 23 0 C

Maximum thickness for each layer

1 mm

Resistance in positive pressure

7 atm according to DIN 1048

1

2

Final Data Adhesive strength in concrete

â&#x2030;Ľ 2 N/mm2

Resitance to humidity

Very good

Resistance to amortization

Very good

Penetrability

Impenetrable

PACKING Monoliti is packed in sacks of 25 kg.

Preservation 12 months from the date of production if preserved in an original packing and protected from freezing and direct sun exposure.

3

350C 50 C

105

06 WATERPROOF COATINGS IZOTRATE

E

CONSUM EN 1504-2

2

/m

0.75 kg

IZOTRATE is a cement based mortar which can be applied with a brush. It contains active chemicals which when in contact with humidity and limestone hydroxide it reacts by forming insolvent crystals. These crystals block the capillary and the cracking caused inside by the shrinkage and inflation of the concrete, preventing the water absorbing.

IZOTRATE offers a number of advantages such as: It is always active protecting permanently the construction against water.

It creates e perfect connection with the concrete by giving to it the desired qualities.

It is capable of closing the cracking up to 400 micron , even in case they are present after application.

In the cases of concrete surface’s damages or of the hydro isolation surface there is no effect on the construction hydro isolation.

It protects the reinforced constructions with steel from the corredation .

It is used to hydro isolate the water tanks or surfaces which are in direct contact with water.

It does not affect the chemical processes of other elements present in the concrete.

It is easily used at a low cost.

This product is classified as a concrete protection layer.

Application Area Concrete surface’s hydro isolation in the cases when

106

humidity is present and in the cases of water pressure.

IZOTRATE is appropriate for the basement’s hydro isolation, septic water tanks as well as mainly of the foundations.

The Support’s Preparation Te support must be clean, out of powder and oil layer’s presence. For very smooth surfaces it is necessary to treat in advance with water with pressure to make it rough.

When there is water presence it is necessary to initially isolate it. When there are obvious cracking in the concrete surfaces, it is necessary to initially close it and clean the surface. If there are pieces of wires in the applicable surface they must be cut to a depth of 2 to 4 cm and after the obtained hole is closed the product can be applied.

Application IZOTRATE is gradually floored at the required water amount by consistently mixing until there is a viscose mass appropriate to apply with a brush. The surface where it can be applied must be a bit wet but it must not have accumulated water. The product must be applied in two layers which must not be more than 1mm thick in order to avoid the possible cracking. After finishing the application the surface must be sprayed with water for following 2-3 days in a such a way that the hydro isolating layer remains a bit wet which gradually reinforces the qualities. Spraying with water the surfaces must be done gradually after the moment that IZOTRATE has started the reinforcement. This is done on the purpose to avoid the damages. The surface is usually sprayed with water 2-3 times a day. The final surface must be protected of rain and freezing. www.dast.al

06 Technical Data Form

Powder

Color

Grey

Mixture density

1.3 gr/cm3

Combustibility

Incombustible

izotrate

Water demand With a spatula

6-7 L water for 25 kg Monolit

With a brush

7-8 L water for 25 kg Monolit

pH of mixture

12

Pot life

3-4 hours

Application time between two layers

after 1.5 hours at 23 0 C

Maximum thickness For each application Resistance at a positive pressure

1 mm 7 atm according to DIN 1048

1

Final Data Adhesive strength in concrete

â&#x2030;Ľ 3 N/mm2

Humidity resistance

Very good

Resistance to amortization

Very good

Penetrability

Impenetrable

CONSUME It is consumed approximately 0.75 Kg/m2 for each layer .

2

PACKING Izotrate is packed in sacks of 25 Kg. Preservation and durability 12 months from the production day if kept at the original packing and protected of freezing and direct sun exposure.

350C

50 C

107

PRIMERS

■ TECNOFIX ■ TECNOFIX LIQUID

■ DW PRIMER ■ HYDRO PRIMER

■ BETON CONTACT ■ GIPS PRIMER

07 PRIMERS TECNOFIX

E

CONSUM EN 998-1

2

1.5 kg/m

Flattening material for surfaces to be coated with decorative coating • It is powder like cement based material, limestone, sand with selected granulometry, hydrophobic synthetic resins and special additives.

• It is characterized of very good spreading and workability which makes easier the product’s application in the sup ports filled with traditional mortar of prepared one.

• The long time of workability, very good adhesiveness with the support and very good flattening of the surface.

• It creates a very good hydro isolation of the surface where it will be placed and this makes easier the a pplication of the decorative coatings.

• It creates a good connection between the basic mortar and the decorative coating.

• Applicable to thicknesses up to 3 mm.

Application Area It is used to flatten and hydro isolate the surfaces which will be coated with decorative coatings (Grafiato or Decortex) in interior and exterior environments. It is applied in traditional mortar based supports or prepared with limestone and cement. The surface where the product is applied can be covered in decorative coatings of mineral or synthetic nature.

110

Important Data • Do not lay other components such as cement, limestone etc in the given product.

• Do not apply on previously painted surfaces.

• Do not apply on plastic surfaces or coatings.

• Do not apply on surfaces with a thickness bigger that 3 mm.

• Do not add water after the composition is prepared.

• Do not use it to level the tiles.

• Apply it at temperatures from +5°C to +35°C. • Do not apply it where there are ceramic coatings. Do not apply it on gypsum based surfaces.

• Do not apply on surfaces which are easy to break or de stroy.

The preparation of the support The support where Tecnofix will be places must be levelled and stable. The surfaces with a thickness of more than 3mm must be levelled in advance before applying the product.

Product’s Application Method The material must be spread with a mechanical spatula in a way to provide a uniform spread in the whole surface.

The second application must be applied 30 minutes after the first one. The environment’s temperature significantly www.dast.al

07

affects the product’s workability time. The lower the temperature the longer the workability time.

Reinforcement with Latex In order to improve the adhesiveness, water impenetrability, plasticity, elasticity, mechanical strength etc, technofix can be reinforced with the Latex additive. The mixture ratio is 1:5 in water (see technical data LATEX).

Cleaning The working tools and hads must be cleaned until the product is not totally dry.

Technical Data (at 230C and 50% U.R) Form

Powder

Color

White

Preservation

12 months in the original packing at a dry place

Combustibility Water demand

Incombustible 7.5-8 liter water for 25 kg Tecnofix

Density of fresh mortar

1.82 gr/cm3

pH mixture

12

Temperature application

+50C to +350C

1

2

Final Data Pot life

3-4 hours

Temperature of application

+50C to +350C

Mixture ph

12

Application thickness

1,5-2 mm

Waiting time for the second application

4-6 hours

Compression strength

≥ 15,0 N/mm2

Flexural strength

≥ 3,5 N/mm2

Resistance to humidity

Good

PACKING: Tecnofix in sacks of 25 kg CONSUME: 1.5 kg/ m2 for 1 mm thickness

3

111

07 PRIMERS TECNOFIX LIQUID

E

CONSUM

0.2-0.225 kg/m

Technical Characteristics • Acrylic based liquid material, resistant to alkali • Treating the surfaces with TEcnofix Liquid enables very good workability as well as obvuious easiness in working the decorative layers.

• It creates isolation and a very good connection of surfaces treated with the decorative layer.

• Easy for use white liner • All the technical characteristics for the decorative coatings that will be used are closely connected to the qualities of the liner that will be applied in advance.

• Tecnofix LIQUID reduces significantly the absorbing ability of the surface to the water.

• It uniforms the absorbing level of the surface where it will be applied.

Product’s characteristics Adhesive qualities It reduces the absorbing quality of the support It neutralizes the pH value.

It does not contain solvent Application Area It is used as a liner of surfaces that later will be painted or coated with refinishes (Bonifin, Fino, Classic etc.) or decorative coatings (Graffiaot, Decortex etc.)

The preparation of the support

112

The support where Tecnofix Liquid is appied initially must be dry and clean of dust and remaining of oil, varnishes, wax and anti adhesive materials. Ht cleaning of oils, varnishes, wax or anti adhesive materials is done mechanically or manually.

The preparation of the product The products after being shaken manually in a bucket is ready for use. It can be diluted up to 100% with water.

Method of Application The product is applied with a brush in a uniform way in the whole surface. Wait at least for 12 hours for Tecnofix Liquid to dry (depending on the temperature) before applying the final product on the support.the low temperatures and the presence of humidity increase significantly the drying time of the product. Do not apply it at temperatures lower than +5°C and higher than +35°C.

www.dast.al

07

Technical Data (at 23 C and 50% U.R) 0

Form

Powder

Color

White

Preservation

12 months in original packing at a dry place

Combustibility

Incombustible

Density

1,2 gr/cm3

Consume

0,2-0,25 Kg/cm3

Mixture pH

7Âą1

Application temperature

+50C to +350C

consume : 0.2-0.25 kg/m2 Packing : plastic buckets 5 kg dhe 20 kg

350C

50 C

113

07 PRIMERS DW PRIMER

E

CONSUM .3 0.2-0 2 kg/m

DW PRIMER is an acrylic resin based liner which is used to provide the desired qualities for the support before applying the cement based tiles adhesive material.

Area of application DW PRIMER may be applied as a first layer in many supports such as in old tiles, polished surfaces, natural stones, cemented floor surfaces, wood and metal.

Guidelines for the preparation Support: the surface where you will DW Primer be applied should be free of moisture, dust and without parts painted with oil.

APPLICATION: DW Primer is ready for use. It is applied directly to the support by means of a roller or brush. The tile’s adhesive can be applied after an hour and as long as DW Primer sticks.

Consume 200 – 300 g/m2 according to the absorbing ability of the support

Packing DW PRIMER is packaged in bottles of 1kg, 5kg, and 10kg.

Preservation The duration of the product is 18 months from the date of production and is kept in the original packing and is protected of freezing and direct sun exposure.

Notes The environmental temperature during the application must be between +5°C and 35°C. The maximal allowed time after the application is 12 hours. If this time is surpassed then it is necessary a new layer before the application of the adhesive material for the tiles.

DW Primer is necessary for flooring tiles over tiles.

350C

114

50C

www.dast.al

07 HYDRO PRIMER

E

CONSUM .3 0.2-0 2 kg/m

Elastomeric Primer for supports where the hydro isolations will be applied.

Polymer in water dispersion which is applied on porous surfaces by significantly increasing the adhesiveness between elastomeric based hydro isolations and the support.

HYDRO PRIMER has a penetrating ability in all the surfaces pores where the hydro isolator will be applied by improving and increasing the adhesive ability between the hydro isolators and the surface which will be hydro isolated.

Application Area Hydro Primer is a ready for use primer which reinforces significantly the adhesiveness of the hydro isolators on layers with concrete, mortar, plaster, panel and gypsum containing.

Application-Consume The surfaces which will be treated with the primer must be totally dry and clean of dust. It is recommended to mix before application. It is easily applicable with a brush or

roller on surfaces before applying the elastomeric hydro isolators.

Packing The product is packed in bottles of 1kg, 5kg and 10kg.

Preservation The product can be preserved for 18 months in the original packing and at a dry place at temperatures from +5째C up to +35째C. Avoid exposing the product at low temperatures(freezing) as well as at high temperatures.

Warning!

It is recommended to apply the product at temperatures +5째C to +35째C.

350C

50 C

115

07 PRIMERS BETON CONTACT

E

CONSUM

0.2-0252 kg/m

Primer used for the treatment of smooth concrete surfaces inside and outside Technical characteristics It is an acrylic resin-based liquid material that is used to treat smooth concrete surfaces.

It provides a very good connection between the concrete and refill layers such as mortar, grout, stucco, waterproofing layers, etc.

By using this material it is possible to eliminate the need of using sprays for the cement in the smooth concrete surfaces.

The treatment of the surfaces with BETON CONTACT provides a very good workability and apparent ease in the application of other layers.

The product is ready to use.

It uniforms the absorbing rate of surface where it will be applied.

Product characteristics Adhesive abilities It lowers the water absorbing ability of the support It neutralizes the ph value It does not contain solvents Areas of use It is used in treating the concrete smooth surfaces which will later be filled in filling mortar, grout etc.

Used as insulating, fixing surfaces will then be painted or worn with other layers of mortar, grout, etc.

Preparation of support The support where BETON CONTACT will be applied must be dry and clean of any dust and of remains of oil, varnishes, wax or anti-adhesive material. The cleaning of the support is done manually or mechanically.

Preparation of product The product must be mixed manually in a bucket and after this it is ready to use and if it is necessary the product may be diluted with water up to 100%.

Product’s application method The product is applied by use of a brush or roller in a uniform manner all over the surface. It is obligatory to wait at least 12 hours for the BETON CONTACT to get dry, varying on the temperature before applying the following product in the support. The low temperature as well as the presence of humidity significantly increase drying time. The product should not be applied if the support’s temperature is lower than +50° C, and we must ensure that it will not get wet up to 24 hours after application.

Final Data Form

Liquid

Color

Amber

Preservation

12 months in original packing in a dry place

Combustibility

Incombustible

Application temperature

+50C to +350C

Density

1.3 kg/l 350C

116

50 C

www.dast.al

07 GIPS PRIMER

E

CONSUM 0.3-0.52 kg/m

Liquid liner for walls which will be covered in gipsputz Gips Primer is a acrylic resin based water disperser, with high resistance to alkali, used for interior environments surfaces. It reduces the supports’ absorbing ability and the combustibility danger. The mass is mixed with water depending on the support ( at ratios: 1:1 up to 1:3).

Technical Characteristics For the uniform of the porosity in high absorbing surfaces.

For interior environments High resistance to alkali The mixing ratio with the water: at ratios: 1:1 up to 1:3 It can be applied with a roller or a brush Color: yellow

cleaning net or with solvents.

Before starting covering with Giptputz, the surfaces must be dry. At any case it is needed to have a drying time of at least 6 hours.

Technical Data Density

1.3 kg/l

Form

Liquid

Consume

0,3-0,5 kg/m2

Preservation

From +5°C to +25°C in a an original packing for 12 months

Application Gips Primer must be mixed with clean water at a 1:1 ratio with weak absorbing, up to the ratio 1:3 in surfaces of high absorbing (Gips Primer- Water). It can be applied with a brush consistently on the surface. The surface’s temperature which will be painted and the temperature of the air must be under +5°C. Important notes After use, the working tool must be cleaned with clean water. The dirt because of Gips Primer, sprayings etc are recommended to be cleaned until they are fresh. The dry material can be removed little by little with water and a 350C

50 C

117

ADDITIVES

■ DW 17 ■ FLEXIT

■ LATEX ■ PLASTOLIT

08 ADDITIVES DW 17

Additive for the DW line adhesives and stuc- Fugacolor and Megafuga must be mixed with DW17 when applying them in walls or floors co (fugacolor, megafuga) for tiles. with humidity which are exposed to atmospheric abrasive agents, moisture, high temperature, Description DW17 is an acrylic based mixture which im- mold etc. in such cases DW17 gives the product proves the adhesive qualities of stucco and tiles. a high resistance and sustainability in time.

It increases the adhesive ability with the support.

It increases the force in bending and repression. Technical Data Color white It improves significantly the flexibility .

It gives a high degree of water resistance to the Density 0.99-1.01 kg/lit product.

It improves the chemical resistance against the atmospheric agents.

Preparation method and consume DW 17 is diluted in the water where the tile adAreas of application hesive or the putty plate will be mixed. Mixing is DW17 is used as a reinforcing additive for the ad- done in the ratios 1:1 or 1:2 in volume. hesives and stuccos for tiles in the cases when high water resistant level is required and in the Preservation cases when higher mechanical power against 18 months from the date of production if kept the chemical agents is required. It is recom- in the original packing, closed, in a temperature mended that the fillers for anti fungus tile grout. between +5 째C and +35째C. it has to be protected from the direct exposure to the sun and frosts.

120

www.dast.al

08 FLEXIT

It is a product made of elastomer which is used as an additive in adhesive materials and in cement based mortars, as well as in mono componential hydro isolators giving them the following characteristics: • High flexibility • Waterproofing • Improved adhesive ability Application area Flexit is used as an elasticizer in the following cases: In the mono componential hydro isolators applicable with a brush (Monoflex), in the cases when the surfaces where it will be applied shows breakings or cracks.

In the tiles’ adhesives of (DW) for the tiles flooring over surfaces characterized of cracks, breakings as well as in the cases when they are exposed to vibrations and shrinkage-inflations.

Appropriate for the tiles and panels’ sticking of the polysterol on the metal, wood, and supports of high deformation rate.

Flexit is recommended to be used as an elasticizer in all the cement based products.

Technical characteristics Type: acrylic polymer in water dispersion Color: white Viscosity: 500±20mPa.s23°C Density: 1.03 kg/lit METHOD OF USAGE AND CONSUME

Preparation of the surface The surface where the adhesive material will be applied must be clean, out of oils or dust; it is recommended to be as flat as possible. In case they’re not so they can be leveled but always taking care to avoid water accumulation.

The elasticizing of adhesive material for tiles Full elasticizing For (25kg) DW (tiles adhesive material) mix with 6 kg FLEXIT (if necessary it can be added an amount of 1-2 lt water) by mixing continuously until a homogenous mixture is formed.

Partial elasticizing For (25 kg) DW is mixed with 3-4 kg Flexit together with an amount of water (approximately 3-4kg) by continuously mixing it until a homogenous mixture is obtained.

Porous surfaces such as concrete, gypsum etc can be treated in advance with a mixture of Flexit/water at a ratio 1:2 . The drying time for the mortars and adhesive material which are mixed with Flexit is twice as big compared to the adhesive and mortars which are not mixed with Flexit.

There are cases when the drying time can last more than 3 days.

Preservation and temperature application The product can be preserved for 18 months in an original packing even in dry places at temperatures from 5°C to 35°C. It is to avoid the exposure of the product to low temperature (freezing) as well as to high temperatures.

121

08 ADDITIVES LATEX

Latex is an additive for the improvement of cement based mortars.

Desription Latex is a synthetic polymer, for the improvement of cement based mortars and concrete layers.

The preparation of the support The supports where the product will be applied must be clean of any dust, fats, oils, stucco remaining, paints etc.

The use of Latex • Joining layer between old concrete and new concrete or mortar.

• For the improvement of cement and limestone based mortar and refinishes.

• It increases the adhesiveness of mortars and impenetra bility from water.

• It is used for cement based hydro isolation mortars ena bling resistance to hydro static pressure.

• It is used for the improvement of mortar’s resistance of the foundations.

• It improves significantly the adhesiveness ability of koll rave and refinishes.

• It protects the concrete surfaces from dehydration.

• The use of latex increases significantly the mechanical resistance, elasticity and impenetrability from water of the cement based construction buildings.

Application LATEX is mixed with the water and the mixing ratio depends on the characteristics we want to obtain from the mortar and the adhesives for tiles. The ratio mixture of Latex with water must not be lower than 1:5. If this ratio is very low then there will be no improvement and reinforcement of mortar’s qualities and cement based adhesives.

For the preparation of the concrete and traditional mortar, initially pour Latex and later cement and sands avoiding the creation of granular materials. Its use increases significantly the product’s workability and the drying time. All cement based mortars which can be mixed with LATEX are characterized of higher adhesiveness and elasticity than mortars which are not accompanied from LATEX.

122

www.dast.al

08 PLASTOLIT

GĂŤlqere

Mortar Plasticiser Description Plastolit is a liquid product which gives plasticity, connection strength and all other limestone advantages to the cement based mortar. It is the idealist layer for the production of the construction mortar, plaster, poor layers etc. It is added in the water which is poured to the mortar and because of the plasticity the water amount is lower.

Preparation Reduce the water amount by replacing limestone with Plastolit.

Wall mortar and poor layers: 50g Plastolit for 25 kg of cement (0.2%) For the preparation of 1 m3 mortar it is necessary to have: 225kg cement; 0.90m3 sand; Plastolit 450g.

For the preparation of mortar for plastering: 75 g PLASTOLIT for 25 Kg cement (0.3%).

For the preparation of 1 m3 mortar it is necessary to have: 0.84 m3 sand; 750g Plastolit.

production if kept in original packing and not opened at temperatures between 5°C and 35°C. Protect it from exposure in sun and freezing.

Plastolit has a better workability when mixed with selected granulometry sand. The added dose (more than 0.4 % of the cement weight) will reduce the consolidation of the mortar.

Packing: in plastic carriers, 5kg and 10 kg.

Warning!

Plastolit can be used within 18 months from the date of

123

LEVELLING COMPOUNDS

■ TECNOFLOR ■ FLATEX

09 LEVELLING COMPOUNDS TECNOFLOOR

E

CONSUM

² 1.4 kg/m m per 1m ss thickne

Do not use it in gypsum or anhydride supports.

Auto leveller with quick drying time for shims Do not use it on prefabricated concrete elements up tot 10 mm.

Do not use it on metallic surfaces Do not use on structures subject to strong moveTechnical Characteri stics ments Cement based powder form product and sand with selected granulometry, synthetic resins and The preparation of the mixture additives which fasten significantly the solidify- Mix 25 kg Tecofloor powder with 6-6. 5 litre waing process. ter by using an electric mixer with 500 rotations Self levelling effect offering good workability and per minute until a homogenous mass is obtained. laying and flat smooth surface Then leave the mixture for 5 minutes to rest and It is shaped in a uniform way in a few hours with- mix again before use. The obtained mass is ready out causing shrinkage. for use in about 45-60 minutes.

Resistant to compression and erosion The Preparation of the Support For interior environments The supports must be flat and stable, mechaniApplication Area The cement floors levelling up to 10 mm thickness.

The levelling before placing the ceramic tiles, natural stone, wood parquet, pvc, carpet etc.

Important Notes 126

cally and dimensionally resistant according to the purpose of use; it must be clean of small pieces, oils, varnishes, wax and anti adhesive materials.

The cleaning of oils, varnishes, wax and anti adhesive materials must be done manually or mechanically.

www.dast.al

09

Technical Data Form

Powder

Colour

Grey

Preservation

12 months in original packing at a dry place

Density of fresh mortar

1.4 gr/cm3

Combustibility

Incombustible

Water demand

6-6,5 liter water for 25 kg Tecnoflor

Pot life

45-60 min

Mixture consistency

Very liquid, self leveler

Workability time

15-20 min

Applicaiotn temperature

from+5°C to +35°C

Passing rate

after 4-5 hours

Time needed for flooring the surface

≥ 2 days

Time needed for flooring the tiles

after 5 days

1

2

Final data Compression strength after 3 days

≥ 15 N mm2

Compression strength after 7 days

≥ 22 N/ mm2

Compression strength after 28 days

≥ 32 N/ mm2

Compression strength after 3 days

≥ 4.5 N mm2

Flexural strength after 7 days

≥ 7,0 N/mm2

Flexural strength after 28 days

≥ 9,0 N/mm2

Resistance to erosion

≥ 0.7 N/ mm2

Brinell resistance

≥ 75 N/ mm2

PACKING TECNO FLOOR packed in sacks of 25 Kg.

350C 50C

127

09 LEVELLING COMPOUNDS FLATEX

E

CONSUM

2

3-5 kg/m

Cement based leveling mortar for interior and exterior environments Technical Characteristics Cement based mortar, selected granulomtry sand and modified polymers It serves for the creation of a flat layer for the application of the of the hydro isolators and adhesive materials.

Application area It is used for the leveling of interior and exterior environments such as pool’s leveling before hydro isolation and other environments before applying the tiles’ adhesives.

During the product’s application the environment’s temperature must be +5°C up to 35°C.

128

Supports’ preparation The support where the material must be applied must be dry, clean, consistent, absorbing, stable. It must not have foreign remaining such as oils, varnishes, oils etc.

Product’s application method The product must be applied manually with a commodity.

When the product is applied with a pump it is to be careful for the consistency of the elaboration and do not mix it with other materials.

www.dast.al

09 Technical Data(at 23°C and 50% U.R) Form

Powder

Color

Grey

Preservation

12 months in an original packing at a dry place

Combustibility

Incombustibility

Density of fresh mortar

1.4 kg/dm3

Application temperature

from+5°C to +35°C

Spreading time

>30 min

Support’s temperature

from+5°C to +25°C

Passing rate

after 4-5 hours

Necessary time to flooring the surface

≥ 2 days

1

Final Data Flexural strength (after 28 days) according EN 1015-11

> 4 N/mm2

Compression strength (after 28 days) according EN 1015-11

> 35 N/mm2

Packing FLATEX is packed in sacks of 25 Kg.

2

350C 50C

129

EXTRA PRODUCTS SILICONS

PRODUCT’S DESCRIPTION D-433 It is a one component silicone based adhesive which has good adhesive ability and waterproofing.

Mainly used in environments with a lot of moisture.

UMEI SUM ONS K CON 280

ml

Product characteristics Easy to use and does not require mixing with other products. Can be opened easily with a silicone application pistol. Due to the characteristics of strength and flexibility it can absorb movement deriving from where the equipment is applied to ensure consistency over time. Being a product resistant to variable temperatures it has no limitations to the application, which means that it can be applied during any season of the year.

Due to the very good waterproof properties and due to additives against mould this product is recommended to be used for hydro isolation in environments where there is a lot of moisture, such as the plumbing equipment in bathrooms. In addition to the aforementioned advantages this product is resistant against UV rays and chemicals.This product can be applied horizontally and vertically as it has the quality of not hanging out.

D-212 Acrylic silicon for general use with very good adhesive and isolating qualities.

This product is appropriate for the isolation and the filling of the joining between walls, windows, PVC tubes as well as for different cracking. The adhesive material forms a very flexible isolating layer after the application.

MEI NSSUUM ON KO C 460

g

MEI UM KCOONNSSU 270

ml

MEI NSSUUM

ON KO C

280

ml

Product’s qualities • Appropriate for filling and isolating most of the construction products such as plaster, concrete, bricks etc.

• Excellent adhesive qualities on porous surfaces without using any primer as well as hydro isolator which can be easily coloured.

• The product is available in white and transparent colour.

D-1500 Acetic silicon with a mono component, with very good adhesive qualities, especially construction materials, resistant to atmospheric agents and impenetrable to water. The silicon D-1500 is used for the adhesiveness and isolation of the joints and spaces of windows; for interior and exterior use.

Product’s qualities • Easy to apply product in ceramic, porcelain supports as well as in porous supports.

• For interior and exterior use • Available in white and transparent colour.

• Before applying the product the support must be cleaned of foreign materials such as paints, oils etc.

D-601 Mono componential neutral adhesive with very good adhesive qualities, resistant to atmospheric agents and impenetrable from water. The support where the product will be applied must be clean, without powder or oils. For a very good application of the silicon, put an adhesive bar in the outer part of the support and after the application of the product and its complete solidifying remove it again.

The silicon D-601 can be applied on all the supports made of construction materials such as: aluminium, bricks, concrete, plastic net, ceramics etc. It serves for the adhesiveness and isolation between the joints of windows and doors.

Qualities of the product: • The silicone D-601 is a product with excellent adhesive abilities on all construction materials as well as on metallic surfaces.

• Easily applicable with very good hydro isolation and resistant to high temperatures.

• The product is available in white and transparent colour.

EXTRA PRODUCTS FOAM

PRODUCT’S DESCRIPTION D-22 It is a mono componential polyurethane isolator foam for general use with very good acoustic and thermo isolation qualities. The foam D-22 is used for isolation between doors, windows’ cases, for the fillings and isolation of spaces for the passing of the tubes, installations and electrical equipments. It has very good adhesive and isolation qualities on all construction materials.

I NSSUUMME

KOON C

750

ml

Product’s qualities • Excellent adhesive qualities on supports such as concrete, plaster, concrete blocks, PVC, glass, wood and aluminium.

• Temperature of application 5°C-35°C. • Optimum temperature of application : 18°C-25°C .

• A product of economic cost. It does not suffer shrinkage after the application.

Warning!

The Foam D-22 is recommended to be preserved 12 months after the date of production at the temperature of 25°C in a fresh ventilated place and without freezing.

EXTRA PRODUCTS PRODUCT’S DESCRIPTION

MESH

DF 90 Code Weigh for each item (g/m2)

Raw material Final product

Resins content Stretching resistance (N/50mm2) Stretching resistance after 28 days in solvent 5% NaOH

In width In width In width In width

Width Length Packing

D-90-5*5mm1.0m*50m=50m2 73±5 90±5 18±2% ≥800 ≥800 ≥50% ≥50% 100cm 50m 4 rolle/cardboard

DF 110 Code Weigh for each item (g/m2)

Raw material Final product

Resins content Stretching resistance (N/50mm2) Stretching resistance after 28 days in solvent 5% NaOH

In width In width In width In width

Width Length Packing

D-110-2.5*2.5mm1.0m*50m=50m2 91±6 110±8 18±2% ≥1300 ≥950 ≥50% ≥50% 100cm 50m 4 rolle/cardboard

DF 125 Code Weigh for each item (g/m2)

Raw material Final product

Resins content Stretching resistance (N/50mm2) Stretching resistance after 28 days in solvent 5% NaOH Width Length Packing

In width In width In width In width

D-125-5*5mm1.0m*50m=50m2 115±9 125±10 16±2% ≥ 1300 ≥ 1750 ≥ 50% ≥ 50% 100cm 50m 4 rolle/cardboard

EXTRA PRODUCTS MESH

PRODUCT’S DESCRIPTION DF 145 Code Weigh for each item (g/m2)

Raw material Final product

Resins content Stretching resistance (N/50mm2) Stretching resistance after 28 days in solvent 5% NaOH

In width In width In width In width

Width Length Packing

D-145-5*5mm 1.0m*50m=50m2 124±9 145±10 16±2% ≥ 1300 ≥ 1750 ≥ 50% ≥ 50% 100cm 50m 4 rolle/cardboard

DF 160 Code Weigh for each item (g/m2)

Raw material Final product

Resins content Stretching resistance (N/50mm2) Stretching resistance after 28 days in solvent 5% NaOH Width Length Packing

In width In width In width In width

D-160-5*5mm 1.0m*50m=50m2 130±9 160±12 16±2% ≥1550 ≥1650 ≥50% ≥50% 100cm 50m 4 rolle / cardboard

NOTE

www.dast.al

NOTE

www.dast.al

NOTE

www.dast.al

Autostrada Tirane -Durres Km 30, Albania Tel: +355 52 25 25 25 Fax: +355 52 25 25 26 e-mail: info@dast.al www.dast.al