anita
IP67 LED in grade uplight, recessed wall mount CSA listed wet label
ANI 2/11
52211_Anita.indd 1
8
2/7/11 12:56 PM
Design by Ares concept - technical manager: eng. Davide Cavalli
ANITA
2 | d e s i g n p l a n / A R E S
52211_Anita.indd 2
2/7/11 12:56 PM
Anita
IP67 CSA
• Description Recessed luminaire for outdoor installation on ground and wall. Configuration: extruded and turned anodized-
aluminium heat sink hosting the power led. Opal or transparent polycarbonate diffuser with silicone gasket and anodized aluminium cap or frame. The base of the luminaire is sealed with polyurethane resin. CSA Listed. complies with LM79 and LM80
• Versions available
The fixture must not be installed in hollow areas.
Diffuser and frame: - Semispherical opal polycarbonate diffuser. - Flat opal or transparent polycarbonate diffuser with anodized-aluminium frame. - Flat transparent polycarbonate diffuser with anodized aluminium cap for side-emission. Power supply: - Constant current 350mA feeding – constant voltage (12-24V DC) feeding on request.
• Light sources
1-led module 1W/constant current 350mA - cool white 6000°K, warm white 3000°K, blue 475nm Accessories on request: - Constant current 350mA power supply - Constant current 350mA dimmable power supply
An efficient drainage of water with a layer of gravel should be forseen - 8” deep.
• Dimensions
- Semispherical and side-emission: Ø 1.34” _ recessing depth including box for installation: 2.75” - Flat diffuser with frame: Ø 1.42” _ recessing depth including box for installation: 2.75” - Box for installation: Ø 2.75” _ recessing depth: 2.75”
Recessed wall fitting
• Technical features
Protection Rating: IP67 - In compliance with EN 60598-1 -
• Installation
Anita is equipped with a piece of bipolar cable (.75”) for an easy-to-make connection. The only connection allowed is “in series”. The only power supply allowed is a constant current I=350mA electronic power supply. The installation requires a dedicated box for installation. Accessory on request: box for installation
The fitting is equipped with 1 cable input
.8 anodized aluminium
The feeding power supply (I out 350 mA) for low voltage must be installed on remote position.
Maximum load (pedastrian traffic): 880 lbs
Protection against impact. IK 09 - 10,00 joule
d e s i g n p l a n / A R E S |
52211_Anita.indd 3
3
2/7/11 12:56 PM
ANITA ALUMINIUM FRAME
U1148772
1 COOL WHITE LED 1W 350mA
1X
1X
1X
U11414472
1 WARM WHITE LED 1W 350mA
opal diffuser
1X
1X
U11414572
1 BLUE LED 1W 350mA
1X
1X
U1148712
40° 1X
U11414412
1 WARM WHITE LED 1W 350mA
1X
NARROW BEAM 1X 10°
WIDE BEAM 1X
U11414512
1 BLUE LED 1W 350mA
1X
WIDE BEAM
1 COOL WHITE LED 1W 350mA
transparent diffuser diffusore trasparente
1X
40° 1X
1X
NARROW BEAM 10°
WIDE BEAM 1X
1X
40° 1X
NARROW BEAM 10°
U1148723
WIDE BEAM
1 COOL WHITE LED 1W 350mA
1X
1X
1X 40°
U11414423
1 WARM WHITE LED 1W 350mA
WIDE BEAM 1X
1X
1X
40°
U11414523
1 BLUE LED 1W 350mA
NARROW BEAM 10°
NARROW BEAM 10°
WIDE BEAM 1X
1X
1X
40°
NARROW BEAM 10°
4 | d e s i g n p l a n / A R E S
52211_Anita.indd 4
2/7/11 12:56 PM
ANITA U1148700
1 COOL WHITE LED 1W 350mA
1X
1X
1X
U11414400
1 WARM WHITE LED 1W 350mA
opal diffuser diffusore opale
1X
1X
1X
U11414500
1 BLUE LED 1W 350mA
1X
1X
1X
d e s i g n p l a n / A R E S |
52211_Anita.indd 5
5
2/7/11 12:56 PM
ANITA ALUMINIUM FRAME-SIDE EMISSION
U1148735
1 COOL WHITE LED 1W 350mA
1X
1X
1X
U11414435
1 WARM WHITE LED 1W 350mA
transparent diffuser
1X
1X
1X
U11414535
1 BLUE LED 1W 350mA
1X
1X
1X
U122
BOX FOR INSTALLATION ø2.64” x H2.75”
6 | d e s i g n p l a n / A R E S
52211_Anita.indd 6
2/7/11 12:56 PM
Power supplies Catalog number
Description
PPLT00109 PPLT00110 PPLT00208
120V 350mA 120-277V 350mA 120V 350mA
Capacity 1-8 FIXTURES NON DIMMABLE 4-12 FIXTURES NON DIMMABLE 3-12 FIXTURES TRIAC DIMMABLE
Note: Anita fixtures are constant current and must be wired in series.
d e s i g n p l a n / A R E S |
52211_Anita.indd 7
7
2/7/11 12:56 PM
79 Trenton Avenue • Frenchtown, NJ 08825 • Tel: (908) 996-7710 • Fax: (908) 996-7042 www.designplan.com The products shown in this catalog are designed and engineered by Willy Meyer + Sohn. They are assembled under license by Designplan Lighting, Inc.
52211_Anita.indd 8
2/7/11 12:56 PM