X Series Centaurs In-grade ETL Listed Wet Label IP68
CX 2/14 79 Trenton Avenue Frenchtown, NJ 08825
www.designplan.com
Tel: (908) 996-7710 Fax: (908) 996-7042
C1X
In-Ground LED Fixture
IP68
Series C1X
Lamp L-LED
. Cast stainless steel body 304 alloy . 1W Cree XPE LED . On-board electronics for 24V DC and 0-10V dimming . Unique “bottle cap” threaded lens frame . No screws to lose . Lens frame turned from solid stainless steel . 0.400” thick tempered glass lens . Walkover, drive over rated for 11,000 lbs at 30 mph . Cast stainless steel 304 alloy junction box . Silicone rubber anti siphon outlet box gasket . Remote power supply . Unit can be through wired for daisy chaining . Class II, not suitable for fountain or pool use. . Requires remote 24V Dc power supply . Available in RGB with remote DMX controller
Wattage 1L-1x1W 3000K LED 3L-1x1W 5000K LED
Body 4-Fully recessed w/cond. entries
listed wet label IP68
Color Temp. SS-Stainles Steel
Note: Other color available
Optic Ballast 0- None X-120vAC-24vDC 1- 6 Degree Spot Remote Driver 2- 25 Degree Flood
Note: LED Optics are for use with 'T' clear glass lens. They are not intended for 'K' or 'G' Lenes
Lens Options 0-None T-CLR. Temp Glass K-Internally Ceramic Coated Tempered Glass G-Frosted Toughened Glass
Note: On board 0-10v Dimming
Power Supplies SERIES
C1X
DRIVER PART #
PPLT00155 PPLT00157 PPLT00158
Designplan Lighting
DESCRIPTION
120VAC-24VDC 30W 120VAC-24VDC 60W 120VAC-24VDC 100W
WATTAGE
1W 24vDC w/ integral 0-10v dim 1W 24vDC w/ integral 0-10v dim 1W 24vDC w/ integral 0-10v dim
UNITS POWERED
SPECIAL DETAILS
1 to 24 1 to 48 1 to 80
parallel parallel parallel
Staten Island 911 Memorial
Lighting Consultant: Fisher, Marantz, Stone
Fixture: C1X
Designplan Lighting
. Cast stainless steel body 304 alloy . 1W Cree XPE LED . On board electronics for 24V DC and 0-10V Dimming . Unique “bottle cap” threaded lens frame . No screws to lose . Lens frame turned from solid stainless steel . 0.400” thick tempered glass lens . Walkover, drive over rated for 11,000 lbs at 30 mph . Cast stainless steel 304 alloy junction box . Silicone rubber anti siphon outlet box gasket . Remote power supply . Unit can be through wired for daisy chaining . Class II, not suitable for fountain or pool use. . Requires remote 24V Dc power supply . Available in RGB with remote DMX controller listed wet label IP68
C2X
In-Ground 24V Dimmable LED Fixture
IP68 Remote Driver Series C2X
Lamp L-LED
Wattage Body 1L-1x1W 3000K LED 4-Fully recessed 2L-1x1W 4000K LED w/cond. entries 4L-1x3W 3000K LED 5L-1x3W 4000K LED Note: Other colors available on request
Finish SS-Stainless Steel
Optic 0- None 1- 10 Degree Narrow 2- 21 Degree Medium 3- 39 Degree Wide 4- 10x44 Degree Elliptical Note: LED Optics are for use with 'T' clear glass lens. They are not intended for 'K' or 'G' Lenes
Ballast X-Remote 24vDC Transformer Required
Lens T-Clear Temp Glass K-Internally Ceramic Coated G-Frosted Tempered Glass
Options 0-None
Note: On board 0-10v Dimming
Power Supplies C2X 1 LED/UNIT
PPLT00155
120VAC-24VDC 30W
PPLT00157
120VAC-24VDC 60W
PPLT00158
120VAC-24VDC 100W
Designplan Lighting
1W 24vDC w/ integral 0-10v dim 3w 24vDC w/ integral 0-10v dim 1W 24vDC w/ integral 0-10v dim 3w 24vDC w/ integral 0-10v dim 1W 24vDC w/ integral 0-10v dim 3w 24vDC w/ integral 0-10v dim
1 to 10 1 to 6 1 to 19 1 to 13 1 to 32 1 to 22
parallel parallel parallel parallel parallel parallel
. Cast stainless steel body 304 alloy . 3x 3W Cree XPE LED . On board electronics for 24V DC and 0-10V dimming . Unique “bottle cap” threaded lens frame . No screws to lose . Lens frame turned from solid stainless steel . 0.400” thick tempered glass lens . Walkover, drive over rated for 11,000 lbs at 30 mph . Cast stainless steel 304 alloy junction box . Silicone rubber anti siphon outlet box gasket . Remote power supply . Unit can be through wired for daisy chaining . Class II . Requires remote power supply listed wet label IP68
C4X
In-Ground 24V Dimmable LED IP68 Remote Driver Series C4X
Lamp L-LED
Wattage 1R-3x1W White 3000K 2R-3x1W White 4000K 3R-3x3W White 3000K 4R-3x3W White 4000K
Body 4-Fully recessed w/cond. entries
Finish SS-Stainless Steel
Other colors available upon request
Optic 0- None 1- Narrow (6°) 3- Wide (25°) 4- Elliptical (6°x25°)
Ballast Q-Remote 24vDC Driver Required (Int. 0-10V Dim.)
Remote Driver to be ordered separately
Lens T-Clear Temp Glass J-Flash White BTM & Non-Skid Top Pattern K-Flash White BTM & Clear Top G-Internally Frosted Toughened Glass Q-Non-Skid Top Patterned Tempered Glass
Options 0-None
Power Supplies C4X 3 LED'S PER UNIT
PPLT00155
120VAC-24VDC 30W
PPLT00157
120VAC-24VDC 60W
PPLT00158
120VAC-24VDC 100W
1W 24vDC w/ integral 0-10v dim 3w 24vDC w/ integral 0-10v dim 1W 24vDC w/ integral 0-10v dim 3w 24vDC w/ integral 0-10v dim 1W 24vDC w/ integral 0-10v dim 3w 24vDC w/ integral 0-10v dim
1 to 6 1 to 2 1 to 13 1 to 5 1 to 22 1 to 8
parallel parallel parallel parallel parallel parallel
Designplan Lighting
. Cast stainless steel body 304 alloy . Cree MCE LED . On board 24vDC with DMX interface individually controlled . Unique “bottle cap” threaded lens frame . No screws to lose . Lens frame turned from solid stainless steel . 0.400” thick tempered glass lens . Walkover, drive over rated for 11,000 lbs at 30 mph . Cast stainless steel 304 alloy junction box . Silicone rubber anti siphon outlet box gasket . Remote power supply . Unit can be through wired for daisy chaining . Class II, not suitable for fountain or pool use . Available anti slip dot pattern glass lens . DMX channels are not field addressable without specialized equipment. If addresses are not specified, the fixture will default to address 1 (1-red, 2-green, 3-blue, 4-white). listed wet label IP68
C4C
In-Ground LED Fixture
IP68 Remote Integral Driver Series C4C
Lamp L-LED
Wattage 3K-5W RGBW LED 4K-5W Dynamic White
Body 4-Fully recessed w/cond. entries
Finish SS-Stainless Steel
PPLT00155 PPLT00157 PPLT00158
Designplan Lighting
Options 0-None
Remote Power Supply.
Power Supplies C4C 1 CREE MCE per unit
Lens Ballast T-Clear Temp Glass X-Remote 24vDC Power Supply Req'd J-Flash White BTM & (INT DMX INTERFACE) Non-Skid Top Pattern K-Flash White BTM & Clear Top Note: Integral 24vDC Driver G-Internally Frosted Board along with individually Toughened Glass controlled DMX interface Q-Non-Skid Top Patterned To be used with Tempered Glass
Optic 0- None 1- Narrow (10°) 2- Med (30°)
120VAC-24VDC30W 120VAC-24VDC 60W 120VAC-24VDC 100W
4.6w 24vDC w/ int. DMX interface 4.6w 24vDC w/ int. DMX interface 4.6w 24vDC w/ int. DMX interface
1 to 4 1 to 9 1 to 16
parallel parallel Parallel
. Cast stainless steel body 304 alloy . 6x 1W Cree XPE LED . Integral power supply for 120V non-dimming . Available in MR16 12V DC halogen with integral power supply . Unique “bottle cap” threaded lens frame . No screws to lose . Lens frame turned from solid stainless steel . 0.400” thick tempered glass lens . Walkover, drive over rated for 11,000 lbs at 30 mph . Cast stainless steel 304 alloy junction box . Silicone rubber anti siphon outlet box gasket . Remote power supply . Unit can be through wired for daisy chaining . Class I . Available anti slip dot pattern glass lens
C7X
In-Ground Fixture Flat Trim IP68
Series C7X
Lamp 6-Halogen L-LED 9-HID
Wattage 14-37W MR16 NSP10 15-37W MR16 NSP25 16-37W MR16 FL40 1F-1Wx6 Ring 3K White LED AM-1Wx6 Ring 5K White LED 2F-1Wx6 Ring Red LED 3F-1Wx6 Ring Blue LED 4F-1Wx6 Ring Green LED 5F-1Wx6 Ring Cyan LED 6F-1Wx6 Ring Amber LED AG-20W MH GE MR16 Spot 3000K AH-20W MH GE MR16 Flood 3000K
Body 4-Fully recessed w/cond. entries
listed wet label IP68
Finish SS-Stainless Steel
Note: MR16 Lamps mounted to adjustable swivel bracket tilt max 15° off vertical.
Grill 1- STD
Ballast T-120V-12V Elect. Integral Trans. J-277V-12V Elect. Integral Trans. C-120V-277V Elect. Integral Trans.
Lens G-Internally Frosted Toughened Glass U-Non Skid Temp Glass T-Clear Temp Glass
Options 0-None
Note: Halogen is either T or J. LED is always C and comes standard with 0-10V dimming. HID metal halide is always C.
Designplan Lighting
. Cast stainless steel body 304 alloy . Xicato 1300lm LED module with integral driver for 120-277V w/ 0-10V Dimming or . 20W MR16 MH adjustable with integral ballast . Unique “bottle cap” threaded lens frame . No screws to lose . Lens frame turned from solid stainless steel . 0.400” thick tempered glass lens . Walkover, drive over rated for 11,000 lbs at 30 mph . Unit can be through wired for daisy chaining . Class I . Available anti slip dot pattern glass lens listed wet label IP68
CDX
In-Ground Fixture
Flat Trim IP68 Series CDX
Lamp 9-HID L-LED
Wattage AG-20W MH GE MR16 Spot 3000K AH-20W MH GE MR16 Flood 3000K FB-39W MH GE MR16 Spot 3000K FC-39W MH GE MR16 Flood 3000K EX-1300lm Xicato 3000K EY-1300lm Xicato 3500K EZ-1300lm Xicato 4000K AG, AH, FB, FC HID Only EX, EY, EZ LED Only
Designplan Lighting
Body 4-Fully recessed w/cond. entries
Finish SS-Stainless Steel
Grill 1- STD
Ballast C-120-277V Integral Electronic L-120-277V w/ Integral 0-10V Dimming Ballast 'C' HID Only Ballast 'L' LED Only
Lens T-Clear Temp Glass Q-Non Skid Temp Glass Patterened
Options 0-None W-Linear Spread Q-Honeycomb Louver S-Solite Lens B-Special Lens (see drawing) Note: Options added to rubber holder.
Drawings C1X
C2X
Designplan Lighting
Drawings C4X
C4C
Designplan Lighting
Drawings C7X
CDX - LED
Designplan Lighting
General Installation Instructions 11/2/07
FAILURE TO FOLLOW THESE INSTRUCTIONS WILL VOID WARRANTY RISK OF ELECTRICAL SHOCK. THIS EQUIPMENT IS TO BE INSTALLED BY A QUALIFIED ELECTRICIAN ONLY. MAKE CERTAIN ELECTRICAL SUPPLY CIRCUIT IS DE-ENERGIZED BEFORE BEGINNING INSTALLATION. CHECK FIXTURE LABEL FOR CORRECT VOLTAGE. READ ALL INSTRUCTIONS CAREFULLY. LOCATION This model is designed for concrete pour installation. The upper edge of the housing must be flush with the prepared surface into which it is recessed. Do not install fixture in a manner that creates a pocket where water can sit on top of fixture. Not suitable for use in places where the luminaire is likely to be exposed to a horizontal stress load caused by braking, acceleration or change of direction. INSTALLATION 1. Lighting fixture comes fully assembled. Note: When not working on fixture replace trim ring for site safety and to protect fixture components from moisture and damage. Keep each trim ring with the original body it was supplied on. Note: Use care to protect O-ring on trim ring. Do not remove, loosen, cut, deform or otherwise disturb O -ring. Keep Oring clean and dry. 2. Set fixture in desired location. Position the fixture in such a manner that the conduit/cable is not stressed at the entry point to the light fixture. 3. The foundation on which the luminaire is to be installed must correspond to the maximum permissible pressure load of the luminaire. Suitable drainage must also be provided. Level the body in two horizontal planes using the three leveling tabs around outer body. The upper edge of the housing must be flush with the prepared surface into which it is recessed. UNDER NO CIRCUMSTANCES MAY IT BE LOWER! 4. Unthread lens assembly from body with tool provided. Ensure that all internal surfaces of the fixture are kept completely dry during installation. Pry out the accessory gasket by using a screw driver. Carefully by hand remove reflector. 5. Connect incoming leads to quick disconnect plug. GREEN WIRE TO “GROUND”, CONNECT BLACK FIXTURE TO BLACK BUIDLING WIRE AND CONNECT WHITE FIXTURE WIRE TO WHITE BUILDING WIRE. Replace tray, lamp, and reflector. Make sure that no wires have been damaged. 6. If using conduit entries, the entries must be sealed with “Dap Heavy Duty Kwik Foam” (not provided). The foam should be sprayed from inside the fixture up into the conduit. Failure by the contractor to use the DAP product could cause a void in the warranty. Replace tray with lamping. If not using through wiring, plug second conduit entry with 3/4" conduit plug. Please make sure wet label requirements are meet. 7. Install lamp and adjust if necessary. Tighten all screws to assure the lamp will not shift after aiming is acquired. Replace reflector and accessory gasket. 8. Place lens frame over fixture ensuring that there is no foreign matter between the lens frame and the body. Start the lamp and bring luminaire to operating temperature (20 to 30min.), this will evaporate the moisture content of air to be trapped. Once operating temperature has been reached, carefully thread the trim assembly to body with tool provided.
DESIGNPLAN LIGHTING, INC., 79 TRENTON AVE, FRENCHTOWN, NJ 08825 T. 908-996-7710 F. 908-996-7042 79 Trenton Avenue Frenchtown, NJ 08825
www.designplan.com
Tel: (908) 996-7710 Fax: (908) 996-7042