DynaScan DS0706 Quickstart by DynaScan Technology, Inc.

Ver.1

DS0706B/L Quick Start Guide

1 Hardware Quick Start 1.1 Power Input and Consumption 1.1.1 Power Control Box for 110V The 110V (100~120V) Power input consists of two

N (Black)

L (RED)

cables. AC3 cable has three lines, (L/N and

Ground (Green)

ground). AC1 and 2 are for Air Con. and Inverter. AC1 consists of red line and black line. AC2 consists of white line and green line.

AS for the detail of the cable, please refer to the table as below. AC1

AC2

AC3

Line Number 2

Descriptions Line (Red)

Line (White)

Line (Red)

Neutral (Green)

Neutral (Black)

Ground (Green) Requirement

5A@ 110VAC( (Max.) 15A@ 110VAC( (Max.)

19A @ 110VAC( (Max.)

AC1&2 AC3

Ver.1

DS0706B/L Quick Start Guide

1.1.2 Power Control Box for 220V L (RED)

N (Black) Ground (Green)

The 220V (200~240V) Power Control box has one AC power cable. The requirement is 19A (Peak). Please connect the Power cable with the 3Poles NFB (300V, 25A) in the Switchboard of the Building. Please follow the instruction to setup your power cable as below.

Ver.1

DS0706B/L Quick Start Guide

1.2 Power Switches Location 1.2.1 DS0706L (With Light Box) Power Switches in the base The Main Power switch is on the base of the display

After you remove the base cover, you will see the Control Box power switch (1), Light Box power switch (2) and Timer (3), The Control Box power switch controls the power of the Power control Box.

Remove the four screws on the both side of base

Light Box

Control Box

Ver.1

DS0706B/L Quick Start Guide

The Power Switches of Power Control Box Open the Light Box Shield First. To remove it, you

As for the white backboard, open the locks on the top

need to open the locks with the enclosed key, and

and bottom sides to open it.

open the shield. Open the locks of Light Box

Open the locks

After opening the white backboard, you will see switches of the Power Control Box

Ver.1

DS0706B/L Quick Start Guide

1.2.2 DS0706B (Without Light Box) Power Switches in the base The Main Power switch is on the base of the display.

After you remove the base cover, you will see the Control Box power button (1), The Control Box power button controls the power of the Power control Box.

Remove the four screws on the both side of base 1

Remove the two screws on the both side of AC Power Box

Control Box

Ver.1

DS0706B/L Quick Start Guide

Open the case door with the key and release the locks on the case. Open the Control box door by releasing the locks.

After opening the door, you will see the Power Control box and IPC Panel.

Power Control box

for 110V

for 220V

Ver.1

DS0706B/L Quick Start Guide

1.3 IPC Installation Please install: 1. Dummy VGA Monitor 2. Audio Cable as the diagram. 2. Audio Cable z Output the audio of Capture card to PC z Please Connect the Audio Out and Line In as it shows Mouse Keyboard

Line In Line Out Mic In

8 in 1 Card Reader

Tuner In, AV In, Audio In, S-Video In, Audio Out Power Button PowerSwitch, Switch,Rest Reset Button

USB

COM2 COM1

RJ-45 DVI Out

Power USB

VGA Out

Speaker (R) Speaker (L) Volume External Audio In External Enable Switch

1. Dummy VGA Monitor z Please Refer to the Appendix for more Info

Use the NTSC/Pal switch connector for the Capture Card if needed.

Ver.1

DS0706B/L Quick Start Guide

1.4 Display Operation 1.4.1 Display on / off Manually Power ON/OFF Steps of Base Side

On the top side, there are three (110V) / two (220V) power

The Panel contains power buttons, breakers

buttons as below.

Steps

1. Power：

1. Turn ON/OFF the display. Please turn ON/OFF

110V：Control LED ON/OFF. 220V：Control LED & Motor ON/OFF.

the Control Box power switch (1). 2. Turn ON/OFF the Light Box (2).(DS0706L only)

2. Air Conditioner：Control Air Conditioner ON/OFF. 3. Inverter(110V only)：Control Motor ON/OFF.

Power ON/OFF Steps for Control Box 2

The Panel contains Power button, circuit breaker 1. Turn ON/OFF the display. Please turn ON/OFF the Circuit

Light Box

Control Box

Breaker

Power switch. 2. Turn ON/OFF the Inverter. (110V only) 3. Turn ON/OFF the Air Conditioner. Please turn them ON always, and turn ON/OFF the display with the Control Box power switch as above. (Base side)

Ver.1

DS0706B/L Quick Start Guide

Turn on: Turn on the main power switch (Control Box) then IPC will power on. Turn off: Turn off the power switch of the IPC. NOTE: If the operating system crashes, please press reset button to restart the IPC and then press power switch again.

1.4.2 Display on / off Automatically You can preset on and off for the display and IPC at a certain time through the software application. When the preset time is up, the display will be powered on automatically, and the IPC will be triggered to power itself on too. If you have preset the item of startup in the software application, the content of the assigned schedule or external multimedia device will be played automatically. (Refer to the software manual for details) NOTE: The main power switch must be always on.

Ver.1

DS0706B/L Quick Start Guide

1.4.3 IPC Operation You can use LCM panel to operate the IPC without keyboard and mouse. Display

Power Indicator

Basic Operation： ENTER：Enter the selected item or save the setting ESC：Go back or Cancel the setting Up/Down： Move the Cursor（>）or

Command Buttons

Change the settings

1.4.4 Put / Change Contents Insert Flash Media card* 1 ,such as MS/MS PRO, SmartMedia, CF/MicroDrive and SD/MMC, into 8-in-1 Card Reader for content playing.

Not include a Flash Media card.

Ver.1

DS0706B/L Quick Start Guide

Steps

1. Save contents to a Flash Media card. (Media files must put in the root directory when you use LCM playing.) 2. Insert media card into the 8-in-1 Card Reader. 3. Choose the control item “Player Control”.

4. Choose the sub-menu “File Source”.

5. Select “All Content” to play the all media.

NOTE: 1.Refer to P.22~23 “Operation Tree of the IPC LCM” for more menu items, please. 2. For more instruction of IPC, please refer to the IPC User Manual.

Ver.1

DS0706B/L Quick Start Guide

1.4.5 Spin Speed Setting The spin speed of the display images. The more “X” is the faster it spins. Steps 1.

Choose the control item “Monitor System”.

Press Up to increase, or Down to decrease. “Fixed” means to stop spinning.

NOTE: 1.Refer to P.22~23 “Operation Tree of the IPC LCM” for more menu items, please. 2. For more instruction of IPC, please refer to the IPC User Manual.

Ver.1

DS0706B/L Quick Start Guide

2 Function / Maintenance Introduction 2.1 AP3 Quick Operation 2.1.1 Start Program To activate AP3, click “START/Programs/ DynaScan AP3/DSPlayer to Start. Normally, the AP3 is running if PC power on when your computers are from DynaScan. Double click and AP3 will be restored.

2.1.2 Main Menu and Functions of Buttons Four Sections on Main Menu Section 1. Those buttons are the main Menu of AP3 Section 2. Video Play control: This part is the control bar for controlling the playing item Section 3. Function operation area. Section 4. Display monitor system.

Ver.1

DS0706B/L Quick Start Guide

2.1.3 Schedule Editing To setup the background sequence file,

Click

Set the Media type as Sequence File

Set the Media type as Sequence File.

Click

Drag the editing file as following picture.

Drag the file to the box as following picture.

Select the media file you need.

Save the sequence editing file.

Drag the file to the box and editing schedule.

to select path and select the file you need.

to select schedule editing.

Ver.1

DS0706B/L Quick Start Guide

2.1.4 Edit Layout Presetting Layout AP3 provides seven layout settings. Click the layout you want, AP3 will load the layout into the editing section and you can start to edit. The Preset layouts are undeletable.

Content Setting There is no content for newly made layout frames. If you do not assign any content to one frame, it will display a black ground when playing. Click

Start Run button to summon the Startup Run Setup window, and then assign

the content and the description of this content. The content with parameters to adjust will show the

button

beside description, and you can click it to setup.

Ver.1

DS0706B/L Quick Start Guide

Ver.1

DS0706B/L Quick Start Guide

2.1.5 Image Spin Speed Select the spin speed of the image(s) on the display screen. It is a drop-down list, and the options cannot be changed, 8 Sec, 16 Sec, -- to 120 Sec. The 8 Sec. means the drum image takes 8 seconds to rotate a round. The default setting is “Fixed”. This means that image(s) is displayed on the screen in a fixed position. You can choose any of them to fit your needs.

Ver.1

DS0706B/L Quick Start Guide

2.2 Move the Machine If you want to move the machine, we suggest that you dissemble the display with the machine and move them separately, or contact the local dealer or DynaScan Technicians to provide professional support. For display moving, we suggest that you use lifting devices. To lift the display, you need to install the eyebolt on the top cover and use the lifting device. Caution: Please make sure that you fasten the eyebolt firmly, or the eyebolt may not carry the display weight and the display will fall down.

For the light-box, please move it carefully to prevent from tilting.

Ver.1

DS0706B/L Quick Start Guide

2.3 Ground Mounting For Safety Reason, you must do the ground mounting to fasten the display onto the ground. Step1. Drive the four anchors into the ground with the drawing shown below. The Minimum depth of hole for an anchor is 95 mm. Note: Please Ensure that the tension strength of each foundation screw with concrete ground mount surface is no less than 585kg. The ground mounted work must be done by civil engineering specialists. After the work is complete, we advise that the reliability of it be checked and approved by authorities concerned in your area for safety purpose. The Ground must be concrete base. Concrete base 250.0

(minimum ψ850

250.0

254.0

3 1 Anchorψ22mm 153mm ANCHOR( 8"*22"L)

195.0

254.0

Back side

75.0

Front side .0 ψ62

Foundation screws 3/

( 4 -10 UNC *4)

Location of Power cord

Ver.1

DS0706B/L Quick Start Guide

Foundation screws 3/

55mm

Note: For the ground is not concrete base, we suggest you can use this kind of foundation screw. (4 -10 UNC)

Step2. Move the display to the preferred place and use the nuts to fix it. Tighten the M16*60 screws to fix the ground-fixing block with the display. The positions are shown below.

Notation: 1. Every foundation screw should have 1 washer & 2 nuts.

0706 machine

4-Screws (M16*60) [provided by Dynascan ] 0706 fix blocks x 4

[provided by Dynascan]

foundation screws & nuts

Ver.1

DS0706B/L Quick Start Guide

3 Reference 3.1 Specifications Model

DS0706L

DS0706B Lamp

LED Type

2.0mm x 2.0mm

Pitch (H x V) Resolution

1092x 304 x 1 screen

Brightness

> 5000 cd/㎡

Color

16.7 millions > 5000 : 1

Contrast Ratio

50” Diagonal x 2

Screen Size (Diagonal)

1.09 m x 0.61 m x 2

Total Display Area (W x H) Viewing Angle(H x V)

>170o x 60 o

Display Area (D x H)

Φ0.70 m x 0.61 m

Φ0.82m x 2.74m

Φ0.82m x 2.03m

470Kg

350Kg

100~120 VAC, 50/60 Hz, 1Φ (110V), 50A or 200~240 VAC, 50/60 Hz, 1Φ (220V),25A Red: 660nm Green: 525nm Blue: 470nm From -20 o to 40 o C 21

Ver.1

DS0706B/L Quick Start Guide

3.2 Operation Tree of the IPC LCM Main Menu

Menu Level 1

Menu Level 2

Menu Level 3

Main Menu

Menu Level 1

Monitor System

Spin Speed Power On Power Off Adj Dis Forward Adj Dis Reverse Temperature Power / Motor System Run Time System Alarm Virtual Enc. Brightness LEDM ON/OFF

Play All Close Select Frame

Player Control

Media File Picture File One File -------------- Sequence File Schedule File File Source --------Layout File All Media All Picture All Content SVideo Video Source ------- AV Tuner Channel Play Pause Play Operator ------- Stop Next Prev. Volume One Two Layout ---------------- Clone Two Clone Three CF/MicroDrive SD/MMC Content Device ----- MS/MSPro SmartMedia Hard Disk

Menu Level 2

Menu Level 3

Ver.1

DS0706B/L Quick Start Guide

Main Menu

Menu Level 1

Menu Level 2

Menu Level 3

Main Menu

OS Protect Clock Country Code Tuner ----------------

Network --------------

Auto Run -----------Option Setting Watchdog------------

Window Adjust -----

Display Setting -----Video Out -------------

Input Type -----------

Cable Antenna

Input Pin DHCP Enable IP Address Subnet Mask Default Gateway Set Cancel Host Name Startup Startup Time Shutdown Shutdown Time Reboot Reboot Time Watchdog Watchdog Timer Left Pos. Top Pos Width Height Brightness Contrast Gamma DVI VGA

Test Pattern

Menu Level 1

Menu Level 2

Menu Level 3

White Red Green Pure Color ---------- Blue No Red No Green No Blue White Red Green Level Color ---------- Blue No Red No Green No Blue

Back Light CF/Micro Drive SD/MMC MS/MSPRO Smart Media Stable Embedded OS------Unstable Update Program----

NOTE: For more instruction of IPC, Please refer to the IPC User Manual.

Ver.1

DS0706B/L Quick Start Guide

3.3 AP3 Default Settings Click

to start option settings. Default settings are shown below.

Setting Function \ Model

DS0706L

DS0706B

Remark

Items Select Model

DS0706

Default setting.

VMR9_WL

Default setting.

Screen Type

Screen2

Default setting.

Auto Startup

Enable

Accelerator

Biling Record Enable Startup Computer ID

User Define

Activate the function to keep the log. It needs to reopen AP3 to enable the setting.

User Define

To set a computer ID number for Biling Record for easy maintenance.

Disable

It's necessary to check it when you'd like to display a upside down content. Select VMR9_RL as accelerator and close it. Reopen AP3 to enable the setting.

Setting VMR9_RL Frame Reversal

To auto activate AP3 when the computer starts.

Content in Sequence Preload

User Define

Content in Schedule Preload

User Define

Sequence in Schedule Preload

User Define

To shorten the blank interval between clips. It only supports Media File, Capture & Picture. Accelerator VMR9 _ WL supports this function. To shorten the blank interval between clips. It only supports Media File, Capture & Picture. To shorten the blank interval between clips. It only supports Media File, Capture & Picture.

Ver.1

DS0706B/L Quick Start Guide

Setting Function \ Model

DS0706L

DS0706B

Remark

Items Serial Port Protocol Ver.

COM3 Auto

Select Monitor System connection port. Default setting is COM3. Select a correct monitor system edition. Default setting is Auto. Forward: Move the screen clockwise.

Display Adjust

User Define

Reverse: Move the screen counterclockwise. Save: Save the setting. Forcefully turn ON or OFF the display power. After Power off, you can’t power on the display until six minutes later.

Monitor

This is for the safety reason. However you can power on the display System

Power Control Enable

Enable

before the countdown is due by pressing the “Force Power On”. Warning: “Force Power On” may cause damage to the display. Please don’t press the button unless you are sure that the display is completely stop operating. Check the checkbox to enable the setting. When the IPC is turned off

Outside Power Off Enable

Disable

by any way except the shutdown time, such as pressing the Power button. IPC will shut the display as well.

NOTE: For more instruction of AP3, please refer to the AP3 Software Manual.

Ver.1

DS0706B/L Quick Start Guide

3.4 Legal Notices In te lle ctu al property; limited license to users T he ha rdwa re and so ftwa re o f our pr oduc ts a re pro tec te d b y c op yr ig h t, tr ademark , pa ten t, a nd /o r o the r in te llec tu al pro per ty laws , a nd a n y un au th or ized use o f the s oftwa re , tra de marks co ntaining h ere in ma y vio la te s uch laws and the so ftwa re lic ense a gre eme n t. Excep t as e x press l y p r o v ide d he r e in , D yna Sc an a nd i ts s upp l iers d o no t gra n t an y e xp r ess or i mp l ied r ig hts to use an y p roduc t r e la te d h ardw are a nd so ftwar e. D yn a Scan is re g istered tr ad ema rk o f D yna Sca n Tech nolog y C orp . in R .O .C an d \or other co un tr ies . Micr oso ft is re g istered tr ad ema rk o f Mic roso ft Cor p . Mo on ligh t is r eg is tere d t r a de mark o f Moo n li gh t c or d les s L td . I B M is re g istered tr ad ema rk o f IBM Co rpor a tion . O ther tra de marks ar e tra demarks o f the ir r espec tive owne rs . D is c la i me r Sp eci fica tio ns and information contained herein are furnished for informational use only. Revisions are periodically made to the information herein; these revisions will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time and are subject to change without notice, and should not be construed as a commitment made by DynaScan. This manual could include mistyping or typographical errors. DynaScan assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. E x c lus i on o f D a ma ges : D yn a Sc a n Tec h n o lo g y C o r p o r a t ion â&#x20AC;&#x2122;s l ia b i l i t y i s lim i ted t o t h e c o s t o f r e pair o r r e p la ce me n t o f the pr oduc t. D yn a Sc an Tec hno lo g y C o r por a ti on s ha ll no t b e l ia bl e for : 1 . Da ma ges to o ther prop er ty c ause d b y a n y d e fec t in the pr oduc t, d amages bas ed up on inco n ven ienc e , loss of us e o f the pr oduc t, loss o f time , loss o f p ro fits , loss o f b usiness o p p o r tu n i t y, l o s s o f g o o d w i l l , i n ter fe r e n c e w it h b u s in e s s r e l a ti o n s h ips , o r o th e r c o mm erc ia l l os s , e v en i f ad v is e d o f t he p os s i b il i t y o f s uc h da mag es . 2 . An y other d amages , wh e the r inc ide ntal, co nseq uen tia l o r o th erw ise . 3 . A n y c la im a ga ins t th e c us t ome r b y an y o t he r par t y. Copyright ÂŠ 2007 DynaScan Technology Corp.

Ver.1

DS0706B/L Quick Start Guide

3.5 Disposal Notices Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new one, the retailer is legally obligated to take back your old appliances for disposal at least for free of charge.

MEMO