ejotherm STR U 2G

Universal screw-in anchor for countersunk and surface fixed installation

• Approved for all building material categories (A, B, C, D, E)

• Countersunk installation - EJOT STR principle with ejotherm STR cap for homogeneous surfaces and even rendering - quick and easy without milling dust • Up to 40% faster installation

• Reduced thermal bridges (0.001 W/K)

• Surface fixed installation using ejotherm STR plugs • Shortest embedment depths, highest loads for maximum safety and economic anchor usage

• Permanent contact pressure

• Pre-mounted screw for quick installation

• 100 % setting control: the countersunk installation of the washer indicates safe anchorage

Notes on ejotherm STR U:

Universal screw-in anchor ejotherm STR U (first generation) is still available in the lengths 115 to 295 mm.

Technical data

Anchor nominal diameter Washer diameter Drill hole depth, countersunk installation h1 ≥ Drill hole depth, surface fixed installation h2 ≥ Embedment depth hef ≥ Screw drive

Point thermal transmission countersunk installation 8 mm 60 mm 50 mm (90 mm) 35 mm (75 mm) 25 mm (65 mm) TORX T30

0.001 W/K

Point thermal transmission surface fixed installation

Use categories acc. to ETA* German DIBt Approval European Technical Approval 0.002 W/K

A, B, C, D, E Z-21.2-1769 ETA-04/0023

Values in parentheses: anchoring in aerated concrete (use category E) *Specification according to ÖNORM B 6124 for concrete, solid brick and vertical brick

Building materials, sorted according to use categories and design loads

For calculation of design loads the national safety factors have to be included (e.g., Germany: 3). Please observe the approval.

Minimum requirements on the raw density and compression strength of stone according to the approval.

Application matrix for the use categories A to D, embedment depth = 25 mm

1) Sample setting is required for perforated block

2) Drilling-out is necessary: use a drill with

Ø 10 mm, drill 40 mm deep into the tolerance layer

3) Only surface fixed

Application matrix with use category E, embedment depth = 65 mm

2) Drilling-out is necessary: use a drill with

Ø 10 mm, drill 40 mm deep into the tolerance layer

3) Only surface fixed

Characteristic loads

A Normal weight concrete C 12/15 acc. to EN 206-1 A Normal weight concrete C 16/20 - C 50/60 acc. to EN 206-1 A Pre-cast concrete panel C 16/20 - C 50/60 B Clay bricks (Mz) acc. to EN 771-1 / DIN 105 B Solid lime sandstone (KS) acc. to EN 771-2 / DIN EN 106 B Solid masonry of lightweight concrete (V) acc. to EN 771-3 / DIN 18152 C Vertically perforated clay bricks (Hlz) acc. to EN 771-1 / DIN 105 C Vertically cored reference bricks (Hlz) acc. to ÖNORM B 6124 C Sand-lime perforated bricks (KSL) acc. to EN 771-2 / DIN EN 106 C Lightweight concrete hollow blocks (HbL) acc. to EN 771-3 / DIN 18151 D Lightweight aggregate concrete (LAC) acc. to EN 771-4 E Autoclaved aerated concrete (AAC 4 - AAC 7) acc. to EN 771-4

1.5 kN 1.5 kN 1.5 kN 1.5 kN 1.5 kN 0.6 kN 1.2 kN 0.75 kN 1.5 kN 0.6 kN 0.9 kN 0.75 kN

Insulation thickness

To allow for differences in thicknesses of build up (adhesive and existing render)

(mm) 10 30 50 70 90 100

60 1151), 3) 1153) 1353)

1552), 3)

80 115 135 155 1752), 3)

1952), 3)

100 135 155 175 195 2152), 3)

2352), 3)

120 155 175 195 215 235 255 140 175 195 215 235 255 2753) 160 195 215 235 255 275 295 180 215 235 255 275 295 315 200 235 255 275 295 315 335 220 255 275 295 315 335 355 240 275 295 315 335 355 375 260 295 315 335 355 375 395 280 315 335 355 375 395 415 300 335 355 375 395 415 435 320 355 375 395 415 435 455 340 375 395 415 435 455 360 395 415 435 455 380 415 435 455 400 435 455 420 455

Insulation thickness

To allow for differences in thicknesses of build up (adhesive and existing render)

(mm) 10 30 50 60 1353) 1552), 3) 80 155 1752), 3) 1952), 3)

100 175 195 2152), 3) 120 195 215 235 140 215 235 255 160 235 255 275 180 255 275 295 200 275 295 315 220 295 315 335 240 315 335 355 260 335 355 375 280 355 375 395 300 375 395 415 320 395 415 435 340 415 435 455 360 435 455 380 455

ejotherm STR installation

Countersunk installation using EJOT STR principle with ejotherm STR cap

1

Surface fixed installation with ejotherm STR plug

1

2

3 2

3

4 4

5

6 5

6

Installation animation EJOT STR principle

ejotherm STR accessories

A broad range of accessories is available for the ejotherm STR U 2G product group

STR caps and plugs Page 24

Combi washer Page 33 STR-tool 2GS and accessories Page 25 and 73

STR renovation cutter Page 27 and 75 VT 2G combi washer Page 16

Product range

Product name and length (mm) ejotherm STR U 2G 115 ejotherm STR U 2G 135 ejotherm STR U 2G 155 ejotherm STR U 2G 175 ejotherm STR U 2G 195 ejotherm STR U 2G 215 ejotherm STR U 2G 235 ejotherm STR U 2G 255 ejotherm STR U 2G 275 ejotherm STR U 2G 295 ejotherm STR U 2G 315 ejotherm STR U 2G 335 ejotherm STR U 2G 355 ejotherm STR U 2G 375 ejotherm STR U 2G 395 ejotherm STR U 2G 415 ejotherm STR U 2G 435 ejotherm STR U 2G 455 Article number 8719 115 400 8719 135 400 8719 155 400 8719 175 400 8719 195 400 8719 215 400 8719 235 400 8719 255 400 8719 275 400 8719 295 400 8719 315 400 8719 335 400 8719 355 400 8719 375 400 8719 395 400 8719 415 400 8719 435 400 8719 455 400

Note: Always use in combination with the ejotherm STR caps or plugs. Packaging unit (pcs) 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 Palett unit (pcs) 5,000 4,000 4,000 3,000 3,000 3,000 2,000 2,000 2,000 2,000 2,000 2,000 1,600 1,600 1,600 1,600 1,600 1,600