HWV-KP5, -KP10, -KP15,
Master Keypad L U T R O N
S P E C I F I C A T I O N
S U B M I T T A L
Job Name
Job Number
Location
Area Controlled
Model No. HWV-KP5, -KP10, -KP15
Color
❏ WHite ❏ BRown
HWV-KP5
❏ BEige ❏ IVory ❏ GRay ❏ BLack ❏ TauPe ❏ Dusty Rose
HWV-KP10
Architectural Style Keypads HWV-KP15
Scene/Monitor Indicator LEDs
Scene/Monitor Indicator LEDs
Scene/Monitor Indicator LEDs
Scene or Zone Buttons
Scene or Zone Buttons
Scene or Zone Buttons
All Off/Lower All On/Raise
All Off/Lower All On/Raise
All Off/Lower All On/Raise
Master Keypad Installation Address switches 1-4
1234
MUX MUX +15V COM
Class 2 wiring connections to other keypads or HomeWorks panel A
Dimensions Inches mm A 2.75 070 B 4.64 116 C 0.32 008 D 0.84 021
B
C
D
Specifications
Power Terminals Mounting Environmental Design System Capacity
1.Turn power off. Strip 1/2” (12mm) insulation from wires in wallbox. Connect pair for low-voltage power to terminals 1 and 2. Connect twisted pair for data link to 3 and 4. 2. ADDRESS: Set first 4 switches with unit’s unique address (see back of this sheet). 3. MOUNT: Push all wires in wallbox and mount as shown. Restore power.
Operating voltage: Class 2, 15 VDC. Capacity: (4) #18 AWG (1.0 mm2). 1- or 2-gang U.S. wallbox. 32°-104°F (0°-40°C). Faceplates: Molded plastic (8 color options shown above). 32 master keypads max. per panel with 16 unique addresses. Data link: 1000’ (300 m) maximum.
Function
Pre-Wiring
These keypads allow users to remotely access button functions to: • turn individual scenes/zones on • or off. • turn selected scenes/zones on • or off as a group. • raise or lower selected scenes/ • zones as a group • monitor lights in different areas.
1. Mount wallbox. 2. Pull cable(s) from HomeWorks panel or other master keypad location. Use one pair #18 for power and one pair twisted and shielded #18 #22 for data. All wiring is Class 2.
Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036, USA 9/96 P/N 362-822
For additional submittal sheets, call our Hot Line and Fax-on-Demand Service at 1-800-523-9466, or visit Lutron’s Web site at http://www.lutron.com/resi
Control Mounting Screws Faceplate
Wallbox Control
Programming
Master keypads are programmed with Lutron’s Windows-based programming utility. Simple programming can be done manually from keypads.
Note: Remote power modules can only be assigned to master keypads by using the Windows programming utility.
Overview of HomeWorks Integrated System Preferred Feed and Load Wiring Entry
Local Vareo Dimmers/Switches - 12 buses available, with capacity of 4 dimmers/switches per bus
Optional High Inductance Filter Choke Locations
Vareo controls can switch or dim zone lighting and override programmed settings
Terminal Blocks handle 8 Remote Power Modules (RPMs), with capacity of 4 Lighting Zones Per Module Master Keypads - 32 keypads maximum with 16 unique addresses possible
RPM Module Locations (8 Maximum Per Panel)
To next panel (Max. 8 Panels)
Master keypads can select pre-programmed lighting scenes, control pathways of light, raise or lower lights, and activate motor driven accessories
Interpanel Link
GRAFIK Eye System - Up to 8 GRAFIK Eye 3100 series controls per panel, with a maximum of 15 accessory controls
HW-LVOC-8 Low Voltage Relay Card Location HW-MA-8-120 Microprocessor Assembly Location Alternate Load Wiring Entries
Control Wiring Entry (Class 2)
Setting a Master Keypad’s Unique Address
Each master keypad requires a unique system address (1-16). This identifies the keypad and enables it to communicate with the remote power panel. To create a keypad’s address, set switches 1 through 4 on the back of the keypad as shown on the right. Document your assignments by noting which master keypad corresponds to each address selected.
For this address
For this address
Set switches like this
Set switches like this
1 2 3 4
1 2 3 4
1
9
2
10
3
11
4
12
5
13
6
14
7
15
8
16 This switch is in the up position This switch is in the down position
Warranty Lutron will, at its option, repair or replace any control that is defective in materials or manufacture within two years after the purchase. This warranty is in lieu of any other warranties, express or implied, and the implied warranty of merchantability is limited to two years from purchase. This warranty does not cover the cost of installation, removal or reinstallation, or damage resulting from misuse, abuse, or improper wiring or insulation. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty may last, so the above limitations and exclusions may not apply to you. Printed in U.S.A. © 1996 Lutron Electronics Co., Inc.