Remote Power Panel L U T R O N
S P E C I F I C A T I O N
Job Name
S U B M I T T A L
HW-MA -8-120
Job Number
Location
Microprocessor Assembly
Model No. HW-MA-8-120
Specifications
Power Mounting Environmental Maximum Communication Capacity
Input Power: 120VAC, 60 Hz Inside HW-PNL8 32° - 104°F (0° - 40°C) 8 Remote Power Modules 48* HomeWorks Vareo dimmers and switches 8 GRAFIK Eye 3100 Preset Dimming Controls 15 GRAFIK Eye accessory controls 7 additional HW-MA-8-120 assemblies 1 RS-232 serial port * For every remote power module used, this number is reduced by four.
Diagnostic LEDs
Diagnostic Display
Local Control Communication Buses
1
2
3
4
5
6
7
8
9
IN
10 11 12
GRAFIK RPM Bus Eye Bus
OUT
123
SW1: Flash Security SW2: Vacation Mode SW2: 24 hr. or 7 day SW3: Enable RS-232 SW3: Feedback
1 2 3 4 C Pin 1, Activate Pin 1, Security Mode Pin 2, Activate Pin 2, Vacation Mode Pin 3, Enable Timeclock Pin 4, Lockout Manual Pin 4, Programming Pin C, Common
Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036, USA 9/96 P/N 362-937
RS-232 Port Pin 2, Transmit Pin 3, Receive Pin 5, Signal Ground
Inter Panel Link
Master Keypad Terminal
Master Keypad Terminal
Panel Address Dial
For additional submittal sheets, call our Hot Line and Fax-on-Demand Service at 1-800-523-9466, or visit Lutron’s Web site at http://www.lutron.com/resi
Overview of HomeWorks Integrated System Preferred Feed and Load Wiring Entry
Optional High Inductance Filter Choke Locations Terminal Blocks handle 8 Remote Power Modules (RPMs), with capacity of 4 Lighting Zones Per Module
RPM Module Locations (8 Maximum Per Panel)
To next panel (Max. 8 Panels)
Interpanel Link
HW-LVOC-8 Low Voltage Relay Card Location
Local Vareo Dimmers/Switches - 12 buses available, with capacity of 4 dimmers/switches per bus
Vareo controls can switch or dim zone lighting and override programmed settings (Typical of 12 buses)
Master Keypads - 32 keypads maximum with 16 unique addresses possible
Master keypads can select pre-programmed lighting scenes, control pathways of light, raise or lower lights, and activate motor driven accessories
GRAFIK Eye System - Up to 8 GRAFIK Eye 3100 series controls per panel, with a maximum of 15 accessory controls
HW-MA-8-120 Microprocessor Assembly Location Alternate Load Wiring Entries
Control Wiring Entry (Class 2)
Description The HomeWorks microprocessor assembly is the center of a HomeWorks system. It communicates with master keypads, Vareo dimmers and switches, GRAFIK Eye preset controls, and remote power modules to operate lights, relays, motors, shades, and other remotelycontrolled devices. The microprocessor assembly (HW-MA8-120) installs in the bottom of a remote power panel enclosure and includes a mounting bracket, power supply, and wiring harness for remote power modules. A maximum of eight microprocessor assemblies can be used in a HomeWorks system, with each assembly having its own unique address.
RS-232 Port An RS-232 port is included for two-way serial communication with a remote PC, providing an interface to/from AV equipment, security systems, HVAC systems, and home automation controls. All system programming can be saved as a file and uploaded through this port, using the Windows-based programming utility.
Time Clock Mode The HomeWorks microprocessor offers a time-of-day clock memory function, capable of storing and executing up to 10 individual events per day. These could be used to automatically turn groups of lights on and off, or operate audiovisual equipment, spas, fountains, or shades.
Security Mode Any lights and controlled devices in the system can be activated by an external security system to turn on and stay on, or flash on and off when an alarm occurs. This mode is activated through a dry contact closure on the microprocessor assembly.
Vacation Mode The HomeWorks microprocessor assembly constantly monitors and records daily lighting and device usage patterns. These patterns can be automatically repeated to simulate occupancy of the home. This mode is activated through a dry contact closure on the microprocessor assembly.
Warranty Lutron will, at its option, repair or replace any control that is defective in materials or manufacture within two years after the purchase. This warranty is in lieu of any other warranties, express or implied, and the implied warranty of merchantability is limited to two years from purchase. This warranty does not cover the cost of installation, removal or reinstallation, or damage resulting from misuse, abuse, or improper wiring or insulation. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty may last, so the above limitations and exclusions may not apply to you. Printed in U.S.A. Š 1996 Lutron Electronics Co., Inc.