24 hrs / 7 days
Important Wiring Information Trim or strip wallbox wires to the length indicated by the strip gauge on the back of the switch. Use the same procedure to wire the new switch as was used with the old switch (see step 4 and below).
• Turn power OFF at circuit breaker (or remove fuse).
120 V~ 60 Hz 15 A
Removing Wallplate and Switch.
OR
Danger: Verify power to switch is OFF before proceeding.
5
Wiring the Switch..
Identifying Type of Circuit.
• Connect the bare copper or green ground wire to the green ground wire on the switch (see Important Note 4). • Connect one of the insulated wires removed from the switch to either of the screws (or pushin terminals) on the switch. • Connect the other insulated wire removed from the switch to the other screw (or push-in terminal) on the switch. • Note: If a single-pole switch is to be replaced with a 3-way switch, the screw on the opposite side of the different colored screw is not used. Tighten it securely and follow instructions for “SinglePole Wiring”.
Single-pole circuit: Insulated wires connected to two screws of the same color. Replace with a single-pole or 3-way switch. Follow wiring “Single-Pole Wiring” when completing step 5.
Ground (bare copper or green wire)
OR
Ground (bare copper or green wire) Tag
3-way circuit: Insulated wires connected to three screws. One of these wires is connected to a screw of a different-color. Tag this wire to identify it when wiring. Replace with a 3-way switch. Follow wiring “3-Way Wiring” when completing step 5.
Different-colored screw (COMMON)
Middle control has two side sections removed.
Ground (Green) wire
Reference Wiring Diagram Ground
Live 120 V~ 60 Hz
Important Note: The wall switch may have two wires attached to the same screw (see illustrations below for examples). Tape these two wires together before disconnecting. When wiring, connect wires to the new switch the same way they were connected to the old switch.
4
• Turn power ON at circuit breaker (or replace fuse).
Single-Pole Switch Light
Neutral
One continuous wire to the screw.
5b - 3-Way Wiring
Disconnecting Switch Wires.
Limited Warranty (Valid only in U.S.A., Canada, Puerto Rico, and the Caribbean.)
Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A. Made and printed in U.S.A. 7/07 P/N 030-948 Rev. A
Turning Power ON.
OR One wire in the backwired hole and one to the screw.
Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after purchase. For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO ONE YEAR FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty may last, so the above limitations may not apply to you. This product may be covered under the following U.S. patent: 7,105,763; and corresponding patents of other countries. U.S. and other patents pending. Lutron is a registered trademark and Ceana and Fassada are trademarks of Lutron Electronics Co., Inc. NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. © 2007 Lutron Electronics Co., Inc.
7
ON
Multigang Installations
Each control has inside section removed.
Align switch and tighten screws clockwise.
5a - Single-Pole Wiring
3
When combining controls in a wallbox, remove all inner side sections prior to wiring (see below). Use pliers to bend side section up and down until it breaks off. Repeat for each side section to be removed. Note: No derating is required if ganged.
Caution: Do not overtighten mounting screws. In a multigang installation, tightening can make it difficult to install the wallplate.
Screw Terminals: Tighten securely. Screw terminals are for use with solid copper wires only. For aluminum wires, consult an electrician. DO NOT use stranded or twisted wires.
• Remove the wallplate and switch mounting screws. • Carefully remove switch from wall (do not remove wires). Turn screws to loosen.
Turn screws clockwise to start.
030-948
1. When no “grounding means” exist within the wallbox then the NEC® 2005, Article 404-9 allows a switch without a grounding connection to be installed as a replacement, as long as a plastic, noncombustible wallplate is used. For this type of installation, cap or remove the green ground wire on the switch and use an appropriate wallplate such as Lutron’s FassadaTM series wallplates. 2. Connect only # 12 AWG or # 14 AWG gauge copper or copper clad wire to switch. See device for strip length. 3. Install in accordance with all national and local electrical codes. 4. DO NOT use CeanaTM switches for compact Fluorescent (Energy Saver) lamps. 5. Clean unit with a soft damp cloth only. Do not use any chemical cleaners.
• Form wires carefully into the wallbox, mount and align switch. • Install wallplate.
030-948
2
Please read before installing
Mounting Switch to Wallbox.
OFF OFF OFF
Important Notes
6
Push-in Terminals: Insert wires fully. Push-in terminals are for use with #14 AWG solid copper wires only. For aluminum wires, consult an electrician. DO NOT use stranded or twisted wires.
1/2 in (13 mm)
OFF OFF OFF
ON ON
ON
Purchase Lutron wallplate separately.
www.lutron.com
ON
120 V~ 60 Hz 15 A
3-way Switch CN-3PS
1-800-523-9466
Installation 1 Turning Power OFF.
Single-Pole Switch CN-1PS
Lutron Technical Support Center
ON
English
Differentcolored screw
Tag Ground (Green wire)
Screw Terminals: Turn screws counterclockwise to loosen.
OR
Push-in Terminals: Insert screwdriver and pull wire out.
Reference Wiring Diagram Ground
Ground
Live 120 V~ 60 Hz
3-Way Switch
3-Way Switch Light
Neutral
• Connect the green or bare copper ground wire to the green ground wire on the switch (see Important Note 4). • Connect the tagged wire removed from the switch to the different-colored screw (or push-in terminal) on the switch. • Connect one of the remaining wires removed from the switch to either of the remaining screws (or push-in terminal) on the switch. • Connect the last wire removed from the switch to the remaining screw (or push-in terminal) on the switch.
?
Technical Assistance If you have questions concerning the installation or operation of this product, call the Lutron Technical Support Center. Please provide exact model number when calling. U.S.A. and Canada (24 hrs/7days) 1-800-523-9466 Other countries 8am – 8pm ET +1-610-282-3800
Fax +1-610-282-6311 http://www.lutron.com
Información Importante sobre Cableado
2
1. Cuando dentro de la caja de empotrar no hay “medios de conexión a tierra” el Artículo 404-9 de NEC® 2005 permite la instalación de un interruptor sin conexión a tierra como reemplazo, siempre y cuando se utilice una placa de pared plástica e incombustible. Para efectuar este tipo de instalación tape o retire el cable verde de conexión a tierra del interruptor y use una placa de pared adecuada como las de la serie FassadaTM de Lutron. 2. Conecte al interruptor solamente cables de cobre o recubiertos de cobre # 12 AWG o # 14 AWG. Vea el dispositivo para establecer la longitud adecuada de la parte descubierta del cable. 3. La instalación se debe realizar de acuerdo con todos los códigos eléctricos nacionales y locales. 4. NO USE interruptores CeanaTM para lámparas Fluorescentes compactas (de Ahorro de Energía). 5. Limpie la unidad con un trapo húmedo solamente. No utilice productos químicos.
Instalaciones con Varios Componentes
Remoción de la placa de pared y el interruptor.
3
Peligro: Compruebe que la alimentación a los interruptores esté desconectada antes de proseguir.
Al combinar controles en una caja de empotrar, extraiga todas las secciones laterales interiores antes de cablear (vea debajo). Utilice pinzas para doblar cada sección lateral hacia arriba y hacia abajo hasta que se quiebren. Repita el proceso para cada sección a remover. Nota: No se requiere reducción de potencia nominal si es agrupado.
O
Tierra (cable de cobre raso o verde) Identificación Tornillo de distinto color (Común)
A cada control se le ha quitado la sección interior
Al control del medio se le han quitado las secciones laterales
Circuito DE 3 POSICIONES: Cables aislados conectados a tres tornillos. Uno de estos cables está conectado a un tornillo de un color diferente. Marque este cable para identificarlo al cablear. Reemplácelo con un interruptor de 3 posiciones. Siga el cableado “Cableado de 3 posiciones” al completar el Paso 5.
Nota Importante: Su interruptor de pared puede tener dos cables conectados al mismo tornillo (vea los ejemplos ilustrados a continuación). Una ambos cables con cinta adhesiva antes de desconectarlos. Cuando realice el cableado, conecte los cables al nuevo Interruptor de la misma forma que estaban conectados al interruptor que se reemplaza.
Un cable continuo al tornillo.
Un cable en el orificio con cableado posterior y uno al tornillo.
Garantía Limitada (Válido solamente en los E.U.A., Canadá, Puerto Rico y el Caribe.) Lutron, a discreción propia, reparará o reemplazará las unidades con fallas en sus materiales o fabricación dentro del año posterior a la compra de las mismas. Para obtener el servicio de garantía, remita la unidad al lugar donde la adquirió o envíela a Lutron, 7200 Suter Rd., Coopersburg, PA 18036-1299, con servicio postal prepago. ESTA GARANTÍA REEMPLAZA A TODA OTRA GARANTÍA EXPRESA Y LA GARANTÍA IMPLÍCITA DE COMERCIABILIDAD ESTÁ LIMITADA A UN AÑO DESDE LA FECHA DE COMPRA. ESTA GARANTÍA NO CUBRE EL COSTO DE INSTALACIÓN, DE REMOCIÓN NI DE REINSTALACIÓN, NI LOS DAÑOS PROVOCADOS POR USO INCORRECTO O ABUSO NI LOS DAÑOS RESULTANTES DE UN CABLEADO O UNA INSTALACIÓN INCORRECTOS. ESTA GARANTÍA NO CUBRE DAÑOS INCIDENTALES O INDIRECTOS. LA RESPONSABILIDAD DE LUTRON ANTE UNA DEMANDA POR DAÑOS CAUSADOS POR O RELACIONADOS CON LA FABRICACIÓN, VENTA, INSTALACIÓN, ENTREGA O USO DE LA UNIDAD NO EXCEDERÁ EN NINGÚN CASO EL PRECIO DE COMPRA DE LA UNIDAD. La presente garantía le otorga derechos legales específicos y usted puede tener otros derechos que varían según el estado. Algunos estados no admiten la exclusión o limitación de los daños incidentales o indirectos, ni las limitaciones en la duración de las garantías implícitas, de modo que las limitaciones anteriores pueden no ser aplicables en su caso. Este producto puede estar cubierto por las siguientes patentes de E.U.A.: 7,105,763; y correspondientes patentes extranjeras. Patentes pendientes de E.U.A., y extranjeras. Lutron es una marca registrada y Ceana y Fassada son marcas registradas de Lutron Electronics Co., Inc. NEC es una marca comercial registrada de la National Fire Protection Association, Quincy, Massachussets. © 2007 Lutron Electronics Co., Inc. Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 E.U.A. Hecho e impreso en los E.U.A. 7/07 P/N 030-948 Rev. A
4
Desconexión de los cables del interruptor.
Bornes de tornillo: Gire los tornillos en sentido contrario a las agujas del reloj para aflojar.
O
Bornes a presión: Introduzca el destornillador y extraiga el cable.
Cuidado: No ajuste demasiado los tornillos de montaje. En una instalación de dispositivos múltiples esto puede dificultar la instalación de la placa de pared.
Alinee el interruptor y ajuste los tornillos en sentido horario.
Cableado del interruptor..
7
5a – Cableado Unipolar
Circuito UNIPOLAR: Los cables aislados conectados a dos tornillos del mismo color. Reemplace con un interruptor unipolar o de 3 posiciones. Siga el cableado "Cableado Unipolar" al completar el Paso 5.
Tierra (cable de cobre raso o verde)
Gire los tornillos en sentido horario para comenzar.
O
5
Identificación del tipo de circuito.
• Coloque los cables cuidadosamente en la caja de empotrar, monte y alinee el interruptor. • Instale la placa de pared
Borneras a presión: Inserte los cables completamente. Las borneras a presión sólo se utilizan solamente con cables de cobre sólido #14 AWG. Para cables de aluminio, consulte un electricista. NO utilice cable retorcido ni trenzado.
Bornes de Tornillo: Ajústelos en forma segura. Los bornes de tornillo deben usarse solamente con cable de cobre sólido. Para cable de aluminio, consulte a un electricista. NO use cable cortado o retorcido.
• Retire la placa de pared y los tornillos de montaje del interruptor. • Retire el interruptor de la pared con cuidado (no saque los cables). Afloje los tornillos.
Montaje del interruptor en la caja de empotrar.
Encendido. • Encienda desde el cortacircuito (o vuelva a colocar el fusible).
• Conecte el cable a tierra verde o de cobre sin aislamiento al cable a tierra verde del interruptor (vea la Nota Importante 4). • Conecte uno de los cables aislados extraídos del interruptor a uno de los tornillos (o bornes a presión) en el interruptor. • Conecte el cable aisaldo restante extraído del interruptor al otro Tierra tornillo (o borne a presión) en el Cable (verde) interruptor. • Nota: Si usted está Diagrama de Referencia de Cableado reemplazando un interruptor Tierra unipolar con un interruptor de 3 posiciones, el tornillo en el lado opuesto del tornillo de color Vivo diferente, no va a ser utilizado. 120 V~ Ajústelo en forma segura y siga 60 Hz Interruptor de las instrucciones para cableado Polo Sencillo unipolar. Luz
OFF OFF OFF
OFF OFF OFF
ON ON
ON
Adquiera la placa de pared Lutron por separado.
13 mm (1/2 in)
6
ON
120 V~ 60 Hz 15 A
Por favor lea antes de instalar
www.lutron.com
Recorte o pele los cables de la caja de empotrar en el indicado en el reverso del interruptor. Utilice el mismo procedimiento que utilizó con el antiguo interruptor para cablear su nuevo interruptor (vea Paso 4 y debajo).
• Desconecte la alimentación en el cortacircuito (o quite el fusible).
Notas importantes
24 horas / 7 días
ON
120 V~ 60 Hz 15 A
Interruptor de 3 vías CN-3PS
1-800-523-9466
Instalación 1 Apagado.
Interruptor de Polo Sencillo CN-1PS
Centro de Soporte Técnico de Lutron
ON
Español
Neutro
O
5b - Cableado de 3 vías • Conecte el cable a tierra verde o de cobre sin aislamiento al cable a tierra verde en el interruptor (vea la Nota Importante 4). • Conecte el cable Rotulado que se removió del interruptor al tornillo de color diferente (o borne a presión) en el interruptor. Tornillo de Identificación • Conecte uno de los cables distinto color restantes extraídos del Cable a tierra interruptor a uno de los tornillos (Verde) restantes (o bornes a presión) en el interruptor. Diagrama de Referencia de Cableado • Conecte el último cable extraído Tierra Tierra del interruptor al tornillo restante (o borne a presión) en el interruptor. Vivo 120 V~ 60 Hz
Interruptor de 3 Posiciones
Interruptor de 3 Posiciones Luz
Neutro
?
Asistencia Técnica Si usted tiene alguna duda con respecto a la instalación o al funcionamiento de este producto, comuníquese con el Centro de Soporte Técnico de Lutron. Por favor, indique el modelo exacto al llamar. E.U.A. y Canadá (24 horas/7 días a la semana) 1-800-523-9466 Otros países 8 a.m. – 8 p.m. (Hora del Este) +1-610-282-3800
Fax +1-610-282-6311 http://www.lutron.com