®
BERTI Macchine agricole S.p.A. Via Musi, 1/A - 3 37042 CALDIERO (VERONA) - ITALIA Tel. +39.045.6139711 - Fax +39.045.6150251 info@bertima.it - www.bertima.it
Mod. MINI/SB: technical specs and description. To fit 1,5 – 2 Tons excavators. Suited to shred grass and green bushes up to Ø 2 cm. Hydraulic mulcher, Mod. MINI/SB 50 : Working width: Weight: Hydraulic Motor: Flow rate required at motor: Operating pressure required:
50 cm; 105 Kg (without mount hitch); Gear type (9 cc); 14-15 lit/ min; 170 – 180 bar;
The MINI/SB range is standard equipped with: self-levelling support for mount hitch; under-plate for mount hitch; electronically balanced rotor with “Y” blades; rear roller; V-belts transmission to the rotor; gear type hydraulic motor with hoses (pressure, return, drain); exclusive block of valves “BERTI FLUID BOX” (see below for futher details)
DATA OF OPERATING MACHINE (Excavator / Back-hoe / etc.) – please fill all below boxes BRAND:
MODEL:
POWER HP:
TRACKED:
WHEELED:
……………………………
…………………….………..
………….……
………….……
………….……
MEASURES FOR MOUNT HITCH (Optional) - please fill below with measures & specs requested X (mm) ………………………………………..……………… If possible, please choose among these: 105; 130; Y (mm) …………………………
Y X
Z (mm) …………………...…
The excavator is equipped with quick hitch
YES
NOT
GREASE NIPPLES ON PINS
YES
NOT
Z Z
BERTI do not manufacture counter-plates for commercial quick hitches HYDRAULIC CIRCUITS IN THE OPERATING MACHINE HYDR. PRIORITY CIRCUIT (*) present in the excavator?
YES
NOT
(* ) It is intended an additional and independent hydraulic circuit in the excavator, which permits to supply constant oil flows values even when operating pressure values are different and even when the operating machine (excavator) is moving itself. In no manner can this supplementary circuit be supplied nor installed by BERTI.
Hydr. CIRCUIT (open) for DEMOLITION HAMMER present in the excavator?
YES
NOT
Hydr. CIRCUIT (close) for DEMOLITION CRUSHER/SHEAR present in the excavator?
YES
NOT
“BERTI FLUID-BOX” This exclusive block of valves makes possible to the user to work with the Berti mulcher at the best of performance, by using the hydraulic circuit of the demolition hammer. The appropriate setting of the hydraulic circuit in the operating machine, must be done by qualified technicians and authorized by the original manufacturer (see also the chapter “SETTING OF FLUID BOX” that follows). BERTI is not responsible for the correct settings in the operating machine !! 1
®
BERTI Macchine agricole S.p.A. Via Musi, 1/A - 3 37042 CALDIERO (VERONA) - ITALIA Tel. +39.045.6139711 - Fax +39.045.6150251 info@bertima.it - www.bertima.it
Mod. MINI/SB: technical specs and description. To fit 1,5 – 2 Tons excavators. Suited to shred grass and green bushes up to Ø 2 cm. SETTINGS OF “BERTI FLUID-BOX” (made in factory): The Fluid Box of the hydraulic mulcher MINI/SB can be set up at the input “P” up to the following max. values (pressures and flow rates): Flow rate (max.) Lit/min
Pressure (max) BAR
Please mark below as desired
20
200
STANDARD**
YES (….)
NOT (…)
35
200
ON REQUEST
YES (…)
NOT (…)
**In the case you do not specify your choice in the above table, the setting of the Fluid Box will be according to the STANDARD values
CORRECT Hydr. SYSTEM
1. Hydraulic Motor, gear type 2.
Return Line, from motor to the Fluid Box (max 15 bar for uni-directional geared motor)
3. BERTI Fluid Box 4. Return Line (T), free flow to the tank of the excavator 5. Oil Pressure Line, from the excavator to the Fluid Box (P) 6 Tank of excavator Drain Line, free flow, to the tank of the excavator. 7. The hose (7) must fish direct into the tank and under the oil surface!! Max pressure in the line must not exceed the value of 2 BAR. 8. Oil Pressure Line, from Fluid Box to the motor
HOSES On the hydraulic mulcher MINI/SB there are three hoses of length of 200 cm from Fluid Box to the excavator: - Oil Pressure Line (item 5 on the drawing) Hose R2 c/w female fitting 1/2” - Return Line free flow into the tank (4) Hose R2 c/w female fitting 1/2” - Drain Line free under oil level (7) Hose R1 c/w female fitting 1/4” All three hoses should reach approx. 60–70 cm from the bottom of the arm. It is a good practice to fit hydraulic cocks at the end of the hoses, in order to limit leakages during the phases of connecting / disconnecting of the hoses. SAFETY The machine is manufactured according to the “CE Directives and Safety Standards”.
2
®
BERTI Macchine agricole S.p.A. Via Musi, 1/A - 3 37042 CALDIERO (VERONA) - ITALIA Tel. +39.045.6139711 - Fax +39.045.6150251 info@bertima.it - www.bertima.it
Mod. MINI/SB: technical specs and description. To fit 1,5 – 2 Tons excavators. Suited to shred grass and green bushes up to Ø 2 cm. CONTACT DETAILS OF THE CLIENT
Company / Client: ………………………………………………………………………………………………………… Address: …………………………………………………………………………………………………………………… Tel.: ………………………………………………….…… Fax: …………………………………………………….….. Contact Person: ……………………………………………………………………………………………………….... Date of compilation: ……………………………
Stamp & Signature: ....…………………………………………..
3