MITUS 212FSA
APPLICATIONS Permanent installations in: Theatres, Concert Halls, Clubs, Places of Worship, Conference Rooms, Indoor Sports, Arenas & Stadiums Sound reinforcement for live events: Touring, Bands, Orchestras
FEATURES 15mm / 0.59" birch plywood enclosure Class D amplifier delivering 1200W RMS 320mm/2x12" B&C neodymium magnet with 75mm/3" coil Frequency response 45Hz - 120Hz DSP on board with 8 presets Input panel with XLR «in&link», volume preset, delay, phase, GND lift switch SPL capability 138dB Wide range of hardware accessories for flying and ground stacked configurations Completely Manufactured in Italy
PRODUCT DESCRIPTION The FBT MITUS 212FSA powered subwoofer meet the following performance criteria: frequency response of 45Hz to 120Hz, peak output of 138dB half-space. The FBT MITUS 212FSA is a vented band-pass design incorporating 2x12" B&C neodymium magnet high excursion woofers with 3" voice coil. The modularity of the FBT MITUS 212FSA makes it extremely flexible for a wide range of applications, from a small system to an elaborate line array system consisting of up to 12 MITUS 206LA cabinets along with multiple FBT MITUS 212FSA subs for large concert events. The FBT MITUS 212FSA provides a DSP with 8 presets cardioid and infra configurations, delay. The control panel provides XLR «in&link», volume, preset, delay, phase 0°-180°, ground lift switch. The MITUS 212FSA feature Baltic birch plywood construction covered in a scratch resistant black paint with a M20 top-mounted stand adapter.
ELECTRICAL PERFORMANCE Built in amplifier
*
Maximum SPL ( continuous / peak )
AC Power requirement
**
PHYSICAL vented band pass
2 x 12" - 3" coil
cont.: 800W RMS
XLR with loop
max.: 1200W RMS
22.6" x 16.5" x 26"
peak.: 2400W
574 x 420 x 660mm
45Hz - 120Hz
30.9" x 20.47" x 27.95"
134dB / 138dB
785 x 520 x 710mm
omnidirectional
80.5 lbs / 36.5 kg
preset dependant
90.4 lbs x 41 kg
640 VA
birch plywood
CONT.: 500mS, rms power on nominal speaker impedance MAX.: 2mS burst, rms power on nominal speaker impedance MAX PEAK: based on max peak output voltage and nominal speaker impedance CONT. SPL: half space, based on continuous power amp rating and LF transducer average sensitivity data, 125mS time average PEAK SPL: half space, based on max peak power amp rating and system peak sensitivity, 10mS time average
MITUS 212FSA
AMPLIFIER MODULE
DIAGRAMS
The FBT MITUS 212FSA provides a high efficiency class D power amplifier module with switching power supply enclosed in a die-cast aluminium chassis. This provides maximum protection of the electronics from dust or dirt, prevents air loss through the input control panel that can cause fastidious noise, and it maximizes heat dissipation avoiding the use of a fan to cool the circuitry.
FREQUENCY RESPONSE 110
dB SPL
105 100 95 90 85 80 75 70 65 60 55 50 10 Hz
20
50
100
200
500
1k
CONNECTION PANEL DO NOT EXCEED RATED MAX CURRENT DRAW FROM AC LOOP OUTPUT CONNECTOR
AC INPUT 220-230Vac 50/60Hz 2.8A max
212 FSA ACTIVE SUBWOOFER
1
1- HUNG 2- HUNG PUNCH 3- HUNG with INFRA 4- GROUND 5- GROUND PUNCH 6- GROUND with INFRA 7- GND CARDIOID FRONT 8- GND CARDIOID REAR 0
MADE IN ITALY
1.5
2
2.5
0.5
3
0
3.5 mt.
DELAY 4
5
3
6 7
2 1
8
+6dB
0 0
AC LOOP OUT 220-230Vac 50/60Hz 16.8A max
POWER CONSUMPTION: 640W
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK NEVER EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE
LEVEL
PRESET OFF
GND LIFT
ON
ON
0! 180! PEAK
IN
All MITUS accessories are specifically rated in agreement with structural computati ons. Never use other accessories when assembling the cabinets than the ones provided by FBT: FBT will decline responsibility over the entire MITUS accessories range if any component is purchased from a different supplier.
DIMENSION DRAWING
380 mm/15.1 inch
574 mm/22.6 inch
660 mm/26 inch
660 mm/26 inch
PHASE LMT PRT
LINK
MITUS 212FSA
ACCESSORIES
MT J206 Joint bar MITUS 212FSA with 206LA
MT F212 Flying bar MITUS 212FSA
RECOMMENDED CONFIGURATIONS MT F212
MITUS 206LA MITUS 212FSA MT S206 MT J206
MITUS 206LA MTS 212 FSA
MITUS 206L_FLYING
EASE FOCUS FBT will place at disposal a software called MITUS 206L_FLYING wich helps calculating the safety factor of the weakest point of MITUS 206LA MITUS 212FSA unit suspension system according to the used configuration and a software called EASE FOCUS that permits an accurate simulation of the mechanical and acoustic bahaviour of the MITUS series line array system.