Service Repair Manual
Models
329E L EXCAVATOR
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
1/12
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 329E L EXCAVATOR WJK Configuration: 329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly C7.1 Engines for Caterpillar Built Machines Media Number -KENR8881-05
Publication Date -01/11/2012
Date Updated -10/05/2016
i06954641
Inlet and Exhaust Valve Springs - Remove and Install SMCS - 1108-010
Removal Procedure Table 1 Required Tools Tool
Part Number
Part Description
Qty
9U-6193
Valve Spring Compressor
1
416-0288
Adapter
1
416-0292
Head
1
9U-6198
Crankshaft Turning Tool
1
9U-7336
Housing
1
5P-7305
Engine Turning Tool
1
A
B(1) B(2) (1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Start By: a. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove" for the correct procedure. Note: Either Tooling (B) can be used. Use the Tooling that is most suitable.
NOTICE Keep all parts clean from contaminants.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
2/12
Contaminants may cause rapid wear and shortened component life.
Note: The following procedure should be adopted to remove the valve springs when the cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves Remove and Install" for the procedure to remove the valve springs from a cylinder head that has been removed from the engine. Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed. Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder bore.
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force.
NOTICE Plug the apertures for the push rods in the cylinder head to prevent the entry of loose parts into the engine.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
Illustration 1
g02313393
1. Follow Step 1.a through Step 1.f to remove the harness assembly for the electronic unit injectors. a. Use a deep socket to remove connections (1) from electronic unit injectors (2). b. Cut cable straps (4) and remove the remaining sections of the cable straps from the cylinder head. c. Disconnect plug (6) from harness assembly (3). d. Remove bolt (5) from harness assembly (3). e. Withdraw harness assembly (3) from the cylinder head. f. Repeat Step 1.a through Step 2 to remove the remaining harness assemblies.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
Illustration 2
g01978814
NOTICE Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
2. Follow Step 2.a through Step 2.d to position the appropriate piston at top dead center.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
4/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
Illustration 3
5/12
g02202973
a. Install Tooling (A) in position on the cylinder head to compress a valve spring (10) for the appropriate cylinder. Note: Ensure that the electronic unit injector label code (12) is not damaged when Tooling (A) is compressed. b. Use Tooling (A) to compress valve spring (10) and open the valve slightly. Note: Do not compress the spring so that valve spring retainer (9) touches valve stem seal (11). c. Use Tooling (B) to rotate the crankshaft carefully, until the piston touches the valve. Note: Do not use excessive force to turn the crankshaft. The use of force can result in bent valve stems. d. Continue to rotate the crankshaft and gradually release the pressure on Tooling (A) until the piston is at the top dead center position. The valve is now held in a position that allows the valve spring to be safely removed. Note: Valve springs must be replaced in pairs for the inlet valve or the exhaust valve of each cylinder. If all valve springs require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 6, 2 with 5 and 3 with 4. Ensure that all the valve springs are installed before changing from one pair of cylinders to another pair of cylinders.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
6/12
NOTICE Do not turn the crankshaft while the valve springs are removed.
3. Apply sufficient pressure to Tooling (A) to allow removal of valve keepers (8). Note: Do not compress the spring so that valve spring retainer (9) touches valve stem seal (11). 4. Remove valve spring retainer (9). 5. Slowly release pressure on Tooling (A). 6. Remove valve spring retainer (9) and remove valve spring (10). 7. If necessary, remove valve stem seals (11). 8. Repeat Step 3 through Step 7 to remove the remaining valve springs from the appropriate cylinder. 9. Remove Tooling (A).
Installation Procedure Table 2 Required Tools Tool
A
B(1)
Part Number
Part Description
Qty
9U-6193
Valve Spring Compressor
1
416-0288
Adapter
1
416-0292
Head
1
9U-6198
Crankshaft Turning Tool
1
9U-7336
Housing
1
5P-7305
Engine Turning Tool
1
Torque Wrench
1
B(2) C
247-5377
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Note: Either Tooling (B) can be used. Use the Tooling that is most suitable.
NOTICE
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.
NOTICE Do not turn the crankshaft while the valve springs are removed.
NOTICE Plug the apertures for the push rods in the cylinder head to prevent the entry of loose parts into the engine
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
7/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
Illustration 4
8/12
g01978814
1. Inspect valve springs (10) for damage and for the correct length. Refer to Specifications, "Cylinder Head Valves" for more information. 2. If necessary, install a new valve stem seal (11) onto the valve guide. Note: The outer face of the valve guide must be clean and dry before installing the valve stem seal. 3. Install valve spring (10) onto the cylinder head. Position valve spring retainer (9) on valve spring (10).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
Illustration 5
9/12
g02202973
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment.
NOTICE Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
4. Install Tooling (A) in the appropriate position on the cylinder head to compress valve spring (10).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Eng...
10/12
Note: Ensure that the electronic unit injector label code (12) is not damaged when Tooling (A) is compressed. 5. Apply sufficient pressure to Tooling (A) to install valve keepers (8). Note: Do not compress the spring so that valve spring retainer (9) touches valve stem seal (11). 6. Install valve spring keepers (8). 7. Carefully release the pressure on Tooling (A). 8. Repeat Step 2 through Step 7 for the remaining valve springs.
The valve spring keepers can be thrown from the valve when the valve spring compressor is released. Ensure that the valve spring keepers are properly installed on the valve stem. To help prevent personal injury, keep away from the front of the valve spring keepers and valve springs during the installation of the valves.
9. Remove Tooling (A). Note: If all valve springs require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following cylinders. 1 and 6, 2 and 5 and 3 and 4. Remember that the crankshaft must not be turned while the valve springs are removed. Ensure that all the valve springs are installed before changing from one pair of cylinders to the other pair of cylinders. If all valve springs do not require replacement, the springs must be replaced in pairs.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Eng...
Illustration 6
11/12
g02313393
10. Follow Step 10.c through Step 10.f to install a new harness assembly (3) to electronic unit injectors (2). a. Position a new harness assembly (3) into the cylinder head. Note: Do not lubricate the O-ring seal. b. Push harness assembly (3) into the cylinder head. c. Install a new bolt (5) and tighten the bolt to a torque of 5.5 N¡m (49 lb in). d. Connect plug (6) to harness assembly (3). e. Use a deep socket to install connections (1) to electronic unit injectors (2). Use Tooling (C) to tighten the connections to a torque of 2.0 N¡m (18 lb in). f. Install the cable straps (4) in to the cylinder head. Note: Ensure that the assemblies of the cable straps are correctly installed into the cylinder head. g. Repeat Step 10.c through Step 10.f for the remaining harness assemblies. End By:
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Eng...
12/12
a. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install" for the correct procedure. Copyright 1993 - 2020 Caterpillar Inc.
Thu Mar 12 16:46:55 UTC+0800 2020
All Rights Reserved. Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
1/7
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 329E L EXCAVATOR WJK Configuration: 329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly C7.1 Engines for Caterpillar Built Machines Media Number -KENR8881-05
Publication Date -01/11/2012
Date Updated -10/05/2016
i03934146
Inlet and Exhaust Valves - Remove and Install SMCS - 1105-010
Removal Procedure Table 1 Required Tools Tool
Part Number
Part Description
Qty
9U-6195
Valve Spring Compressor
1
268-1969
Adapter
1
276-1221
Head
1
A
Start By: a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove" for the correct procedure.
NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.
1. Clean the bottom mating surface of the cylinder head. Check the depth of the valves below the face of the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder Head Valves" for the correct dimensions.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
2. Place a temporary identification mark on the heads of the valves in order to identify the correct position. Note: Inlet valves have a recess in the center of the head. 3. Use a suitable lifting device to position the cylinder head with the valve springs upward. The weight of the cylinder head is approximately 65 kg (143 lb). Note: Ensure that the cylinder head is kept on a clean, soft surface in order to prevent damage to the machined face.
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force.
Illustration 1
g01978994
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
2/7
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
3/7
4. Install Tooling (A) into position on the cylinder head in order to compress appropriate valve spring (3).
NOTICE Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
5. Apply sufficient pressure to Tooling (A) in order to remove valve keepers (1). Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal (4). 6. Slowly release the pressure on Tooling (A).
Illustration 2
g01978995
7. Place a temporary identification mark on valve spring (3) in order to identify the correct position. 8. Remove valve spring retainer (2). Remove valve spring (3). 9. Repeat Step 4 through Step 8 for the remaining valves.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
4/7
10. Remove Tooling (A). 11. Remove valve stem seals (4). 12. Use a suitable lifting device to turn over the cylinder head. 13. Place a temporary identification mark on valves (5). Remove valves (5) from the cylinder head.
Installation Procedure Table 2 Required Tools Tool
A
Part Number
Part Description
Qty
9U-6195
Valve Spring Compressor
1
268-1969
Adapter
1
276-1221
Head
1
NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.
Note: The valves have a hard surface finish. Grinding compound must not be used on the valves. Grinding compound will damage the hard surface finish of the valves. 1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant passages, and, all lubrication passages in the cylinder head are free from debris. Follow Step 1.a through Step 1.e in order to inspect the components of the cylinder head assembly. Replace any components that are worn or damaged. a. Inspect the cylinder head for wear and for damage. Refer to System Operation, Testing and Adjusting, "Cylinder Head Inspect" for the correct procedure. b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for more information. c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder Head Valves" and System Operation, Testing and Adjusting, "Valve Guide - Inspect" for more information. d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for more information.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
5/7
e. Inspect the valve springs for damage and for the correct length. Refer to Specifications, "Cylinder Head Valves " for more information.
Illustration 3
g01978995
2. Lubricate the stems of valves (5) with clean engine oil. Install valves (5) in the appropriate positions in the cylinder head. Check the depth of the valves below the face of the cylinder head. Refer to System Operation, Testing and Adjusting, "Valve Depth - Inspect" for more information. 3. Use a suitable lifting device to turn over the cylinder head. The weight of the cylinder head is approximately 65 kg (143 lb). Note: Ensure that all of the valves remain in place. 4. Install new valve stem seals (4) onto each of the valve guides. Note: The outer face of the valve guides must be clean and dry before installing valve stem seals (4). 5. Install valve spring (3) onto the cylinder head. Position valve spring retainer (2) on valve spring (3).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force.
Illustration 4
g01978994
6. Install Tooling (A) in the appropriate position on the cylinder head in order to compress valve spring (3).
NOTICE Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
7. Apply sufficient pressure to Tooling (A) in order to install valve keepers (1).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
6/7
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
7/7
Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal (4).
The valve spring keepers can be thrown from the valve when the valve spring compressor is released. Ensure that the valve spring keepers are properly installed on the valve stem. To help prevent personal injury, keep away from the front of the valve spring keepers and valve springs during the installation of the valves.
8. Carefully release the pressure on Tooling (A). 9. Repeat Step 5 through Step 8 for the remaining valves. 10. Remove Tooling (A) from the cylinder head. End By: a. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" for the correct procedure. Copyright 1993 - 2020 Caterpillar Inc.
Thu Mar 12 16:47:51 UTC+0800 2020
All Rights Reserved. Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
1/3
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 329E L EXCAVATOR WJK Configuration: 329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly C7.1 Engines for Caterpillar Built Machines Media Number -KENR8881-05
Publication Date -01/11/2012
Date Updated -10/05/2016
i03934079
Engine Oil Filter Base - Remove and Install SMCS - 1306-010
Removal Procedure Table 1 Required Tools Tool
Part Number
A
1U-8760
Part Description Chain Wrench
Qty 1
NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.
NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
Illustration 1
g01980935
1. Place a suitable container below engine oil filter (5) in order to catch any oil that might be spilled. 2. Use Tooling (A) to remove engine oil filter (5). Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure. 3. Remove bolts (3). Note: If bolts of different lengths are installed, identify the correct position of the bolts. 4. Remove engine oil filter base (4). 5. Remove gasket (6). 6. If necessary, remove plug (1) from engine oil filter base (4). Remove O-ring seal (2) from plug (1).
Installation Procedure NOTICE Keep all parts clean from contaminants.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
2/3
Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING
NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
3/3
Contaminants may cause rapid wear and shortened component life.
Illustration 2
g01980935
1. Clean engine oil filter base (4). Clean the gasket surfaces of the cylinder block or the engine oil cooler. 2. If necessary, install new O-ring seal (2) to plug (1). Install plugs (1) to engine oil filter base (4). Tighten the plug to a torque of 12 N¡m (106 lb in). 3. Install bolts (3) to engine oil filter base (4). 4. Install a gasket (6) onto bolts (3). Install the assembly of the engine oil filter base to the cylinder block or the engine oil cooler. 5. Tighten bolts (3) to a torque of 22 N¡m (195 lb in). 6. Install a new engine oil filter (5) and check the level of the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil Level - Check" for the correct procedure. Copyright 1993 - 2020 Caterpillar Inc.
Thu Mar 12 16:48:46 UTC+0800 2020
All Rights Reserved. Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
1/6
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 329E L EXCAVATOR WJK Configuration: 329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly C7.1 Engines for Caterpillar Built Machines Media Number -KENR8881-05
Publication Date -01/11/2012
Date Updated -10/05/2016
i03934080
Engine Oil Filter Base - Remove and Install - Engine Oil Filter Base with Adapter SMCS - 1306-010
Removal Procedure Start By: a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter Base - Removal and Install" for the correct procedure.
NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.
NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
329E & 329E L Excavators WJK00001-UP (MACHINE) POWERED BY C7.1 Engin...
Illustration 1
g02047393
Typical example
1. Remove bolts (1), bolts (2) and bolts (3). Note: Note the position of the bolts and the length of the bolts.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2020/3/12
2/6