HP 35 available to the rotor HP 45 max to hydraulic motor
T500G GROUP
HYDRAULIC REACH MOWERS
SMART
A
Parallel arm geometry Drop forged joint brackets for arms linkage
Independent hydraulic system Polypropylene oil tank
Floating head system
Reversible rotor by cable
Cast iron hydraulic rotor pump group 3 Adjustable rear roller
Hydraulic break-back on power slew ram with max relief valves
Cast iron engine with gear installation
Cast iron hydraulic rotor pump group 3
Cable controls
Electric Proportional Controls with rotor start and stop by electric switch
Boxed rotating bracket
new
60
70
80
T500G Smart Farm
Min. tractor weight
Min. tractor width
Kg
m
2500
1,90
F
Working positions (m) T500G Smart Farm
Developed in collaboration with:
m
5,00
B
m
3,06
C
m
1,46
D
m
3,62
E
m
4,84
F
m
2,15
G
m
1,69
H
m
4,77
H
The polypropylene oil tank is separated from the frame and allows it to be isolated from any structural stress. Fully recyclable.
A
E
Hydraulic breakaway on power slew ram with max. relief valve (safeguards arm in case of obstacles)
HP Tractor
D
90째
C G B
A
Technical data Model
T500G Smart Farm
Max horizontal reach*
Weight
Oil
Rotor
Pto
m
Kg
l
Rpm
MAX Rpm
5,00
860
120
3.100
540
Flail head angle
235°
* Reach measured from tractor centre line to head edge.
Machines with cable controls “Classic”
Equipped with:
Model
Flail head
T500G Smart Farm with flail head TI120 m 1,20
Floating Head system
Machines with electro-hydraulic proportional control “EP-Tronic”
The polypropylene oil tank, fully recyclable
Model
Boxed rotating bracket
T500G Smart Farm EPTronic with flail head TI120 m 1,20
Hydraulic breakaway on power slew ram with max. relief valve (safeguards arm in case of obstacles)
Completing equipment to the base machine WARNING: due to the high offset loads on the linkages it is necessary to fit two stabilizers Code
Lenght
TST5017
(640-890)
Stabilizers to the tractor “Delta yoke” for stabilizers
0PT001121000 TGA4611
(640-890)
Stabilizers for “Delta yoke”
TGA5014
(340-460)
Top link stabilizer
Mechanic roll-over protection system (SAB) Block valve on slew ram (better stability and safety in transfer) Totally Independent hydraulic system Cast iron hydraulic rotor pump group 3
Option
Cast iron hydraulic motor
Code
TM46002
Oil cooler with thermostat
Reversible rotor by cable
TM46003
Lift float (LFA mechanic)
TM46008
Bumpers with illumination system
Front and rear abrasion resistant guard for flail head
Flail head
TI 120
Width (m)
1,20
Rotor speed (rpm)
3100
Blade tip speed (m/sec)
60
Flail head angle
235°
Weight (Kg)
210
Oil and PTO shaft
TI 120
Flails TI 120 Interchangeable on the same rotor Multi-use blades for: grass, shrubs, bushes, sticks, wood
Spoon blade for: grass, shrubs, bushes, sticks, wood
“T” Hammer for woods
Ø max 3 cm
Ø max 2 cm
Ø max 4 cm
Warning Cod. 0901146
Cod. 0901164
Cod. 0901147
n° 44
n° 22
n° 22
Standard
FERRI srl - Via Govoni, 30 - 44034 Tamara (FE) Italy - Tel. +39 0532 866866 - Fax +39 0532 866851 - info@ferrisrl.it - www.ferrisrl.it Spare parts: Tel: +39 0532 866993 - Fax: +39 0532 867061 - e-mail: parts@ferrisrl.it After Sales Service: Tel: +39 0532 866991 - Fax: +39 0532 866851 - e-mail: service@ferrisrl.it
IT IS RECOMMENDED that the connection between tractor and shredder and its setting up should be made with the Dealer according the instructions and warnings listed on our Use and Maintenance Manual. For further information please contact our after sales service.