HP 54 (Energy) available to the rotor HP 60 (Power) available to the rotor HP 64 (Energy) max to hydraulic motor HP 79 (Power) max to hydraulic motor
GROUP
HYDRAULIC REACH MOWERS
ENERGY
A
Parallel arm geometry Electric Roll-over protection system SAB (option) Stiff pipes
Power slew 95°
Pressurized oil tank
Floating head system Flail head 1,25 m
Oil cooler in Alluminum with thermostat
“Overlap” spiral rotor with two spiral rows
Frame variable section
Automatic hydraulic block for transport
Electronic proportional controls 1st arm rectangular section (mm 120x180)
95°
Hydraulic break-back with accumulator controlled autoreset facility (SRA)
Piston hydraulic system in closed circuit (Power Version)
Min. tractor weight **
Min. tractor width **
Kg
m
TSH 600G
3600
2,30
TSH 650GZ
3600
2,30
HP Tractor
100
110
120
(**) for a better tractor stability it is recommend to use the universal axle bracket (cod. ARK 200) and relevant completing kit
Working positions (m) TSH 600G
TSH 650GZ
A
m
6,05
6,62
B
m
4,17
4,73
C
m
1,20
1,20
D
m
5,51
5,90
E
m
7,20
7,62
F
m
2,31
2,82
G
m
1,7
1,7
H
m
6,27
6,85
Technical data Model
TSH 600G Energy TSH 650GZ Energy TSH 650GZ Power
Max horizontal reach*
Weight
Oil
Telescopic extension
Rotor
P.t.o.
Flail head angle
m
Kg
l
m
rpm
MAX rpm
6,05
1.510
170
-
3.000
540
235°
6,62
1.670
170
0,60
3.000
540
235°
6,62
1.670
140
0,60
2.800
540
235°
(*) Reach measured from tractor centre line to head edge.
Equipped with:
Machines with Electric Proportional Controls “Advance Tronic” Model
Flail head TNS 125 (Energy version)
Flail head TNSC 125 (Power version)
TSH 600G Energy Advance Tronic with flail head TNS 125 m 1,25
Wire trap Rear roller Ø 140 mm Rotor balancing on side
TSH 650GZ Energy Advance Tronic with flail head TNS 125 m 1,25 TSH 650GZ Power Advance Tronic with flail head TNSC 125 m 1,25
flanges
Replaceable skids Piston hydraulic system in
Completing equipment to the base machine Code
Length cm
TK8005/06 OPT001121000 TSN5033 TGA5018 TGA5019 ARK200 –
(705-920) (340-460) (485-720) -
closed circuit (Power version)
Stabilizers to the tractor “Delta yoke” for stabilizers Stabilizers for “Delta yoke” Top link short Top link long Axle Brackets Axle Plates Kit (x ARK200)
Electronic proportional
controls “Advance Tronic”
Oil cooler in Alluminum with thermostat
Telescopic extension m 0,60 (TSH 650GZ)
Mechanic Roll-over protection system
Hydraulic break-back with
Option
accumulator controlled autoreset facility (SRA) – with electric disengagement (PSS), a maximum relief valve is available for arm protection
Code
TSB7032 –
Lift float (LFA electric) Electric roll-over protection system
Electric reversible rotor (DSR Electric)
Flail head
TNS 125
Floating head system Hydraulic Power slew 95° Bumpers with illumination
TNSC 125
Cutting width (m)
1,25
1,25
Rotor speed (rpm)
3000
2800
Blade tip speed (m/sec)
60
60
Flail head angle
235°
235°
Weight (kg)
290
315
system
TNS 125 (Energy) Motor with direct drive
TNSC 125 (Power) Side toothed belt drive
Front and rear abrasion
resistant guard for flail head
Oil and Pto shaft
Flails / TNS 125 - TNSC 125 Interchangeable on the same rotor Multiuse blades for: grass, shrubs, bushes, sticks, wood Ø 4 cm
“T” Hammer blades for wood Ø max 5 cm
Unidirectional blades Ø max 6 cm
Cod. 0901181
Cod. 0901141
Cod. 0901187
n° 52
n° 26
n° 26
Standard
FERRI srl - Via Govoni, 30 - 44034 Tamara (FE) Italy - Tel. +39 0532 866866 - Fax +39 0532 866851 - info@ferrisrl.it - www.ferrisrl.it Spare parts: Tel: +39 0532 866993 - Fax: +39 0532 867061 - e-mail: parts@ferrisrl.it After Sales Service: Tel: +39 0532 866991 - Fax: +39 0532 866851 - e-mail: service@ferrisrl.it
Warning IT IS RECOMMENDED that the connection between tractor and shredder and its setting up should be made with the Dealer according the instructions and warnings listed on our Use and Maintenance Manual. For further information please contact our after sales service.