KS Installation & Maintenance Guide by Franke South Africa

FRANKE Kitchen Systems Installation & Maintenance Guide

recommend that all installations and maintenance be carried out by registered * Franke professionals.

INDEX How to install INSET SINKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 How to install UNDERMOUNT SINKS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 How to install DROP-ON SINKS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 How to install SINK MIXERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Fault Finding - SINK MIXER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 How to change a SINK MIXER CARTRIDGE . . . . . . . . . . . . . . . . . . . . . . . 14 - Boston Swivel - Razzo Swivel - Flair Swivel - Billy Joystick Professional / Swivel - Enix Square Swivel - Highrise Swivel - Cascade Professional / Prep Bowl - Projectline Single Lever / Wall Mounted

15 17 19 21 22 25 27 29

Sink Mixers - SPARES MATRIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 How to install a WASTE DISPOSER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 How to install a WASTE DISPOSER AIR SWITCH. . . . . . . . . . . . . . . . . . 34 How to install a SPAZI F1 SINGLE BOWL. . . . . . . . . . . . . . . . . . . . . . . . . . 35 How to install a SPAZI F2 DOUBLE BOWL. . . . . . . . . . . . . . . . . . . . . . . . . 39 How to install a SPAZI F3 TRIPLE BOWL . . . . . . . . . . . . . . . . . . . . . . . . . . 43 How to install a WASHTROUGH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

How to install INSET SINKS For installation of Inset sinks into MDF type work tops

Trace the cut out template onto the work top. The template is included in the packaging as a perforated tear out.

Drill holes into work top at each corner of the marked area to allow for easy cutting of the MDF.

Follow the lines of the template and cut worktop with a jigsaw.

To ensure that the worktop is water resistant, seal inside edge of cut out with a resin and hardener compound.

Allow to dry until the compound forms a silicone like surface on the cut area to prevent swelling of the MDF in the event of water seepage.

Fix clips to sink. Ensure there are a minimum of 4 clips on either length side of the sink.

How to install INSET SINKS

9. Place sink onto work top.

10.

11.

12.

Remove screws from each clip so that the sink will fit perfectly into the cut out. These screws will then be re-attached to the sink clip, working from the underside of the work top.

Generously apply silicone onto folded edge of sink and along the edge of the cut out. Silicone acts as glue and further prevents water seeping underneath the work top.

Attach screws to clips and tighten to its maximum tension. The tightening ensures that the sink is pulled down firmly onto the work top preventing the sink from lifting at the edges and bowing.

Silicone Sealant

Wipe away oozing silicone from the work top and smooth out edges.

Resin & Hardener

Allow to set for 24 hours.

Pencil

Silicone Sealant

Jigsaw

Resin & Hardener

Flashlight

Drill - 9mm or larger bit

Paint Brush

Nut Driver - 9mm (3/8â&#x20AC;?)

Tape Measure

Screwdriver - shank at least 152mm (6â&#x20AC;?)

How to install INSET SINKS For installation of Inset sinks into Granite / Marble type work tops

polish Trace template on 2. inside edgeCut ofandgranite 1. granite slab as per slab to smooth out the edges. template provided on the (Optional)

packaging or programme specifications into CNC system.

Mark out the position 3. of each of the sink clip lugs on the under side of your

Using a Diamond Disk, cut a 60mm groove, 4. 2-3mm deep along marked

line.

work top, off set buy 12mm of the cutout.

Remove screws from each clip so that the sink will fit perfectly into the cut out. These screws will then be re-attached to the sink clip, working from the underside of the work top.

Fix clips to sink. Ensure there are a minimum of 4 clips on either length side of the sink.

How to install INSET SINKS

8. Place sink onto work top.

10.

11.

12.

Generously apply silicone onto folded edge of sink and along the edge of the cut out. Silicone acts as glue and further prevents water seeping underneath the work top.

Attach screws to clips. Ensure that the clips are lined up with the already cut grooves.

Tighten the screws to their maximum tension. The tightening ensures that the sink is pulled down firmly onto the work top preventing the sink from lifting at the edges and bowing.

Silicone Sealant

Wipe away oozing silicone from the work top and smooth out edges.

Allow to set for 24 hours.

Pencil / Marker

Silicone Sealant

Flashlight

Angle Grinder & Diamond Disk

Tape Measure

Screwdriver - shank at least 152mm (6â&#x20AC;?)

How to install UNDERMOUNT SINKS

Trace template on Cut and polish inside 1. 2. granite slab as per edge of granite slab to template provided on the smooth out the edges. packaging or programme specifications into CNC system.

To centralise the sink over the cut out area, 3. mark each corner of the sink

Make centred markings 4. along each edge of the sink, offset by 10mm

onto the granite slab.

Drill a 8mm hole on Insert a Plastic M6 5. each centred marking, 6. Socket into each drilled 12mm 15mm deep hole and tap them into to (depending on thickness of the granite.

place.

Apply silicone onto Position the 7. under side of granite 8. undermount sink onto slab along the edge of the cut granite slab. out.

How to install UNDERMOUNT SINKS

Remove excess Fit clamps on to each 10. silicone from the 9. edge of the sink, inside edge of the sink / fastening them to the Plastic granite.

M6 Sockets.

Silicone Sealant

24 hours for 11. Allow the silicone to dry.

Pencil

Silicone Sealant

G-Clamps

Nut Driver - 9mm (3/8â&#x20AC;?)

Flashlight

Screwdriver - shank at least 152mm (6â&#x20AC;?)

Tape Measure

How to install DROP-ON SINKS

Trim cleat to allow for easy installation.

Place sink cupboard top.

TRIMMING: Inside of the carcass is trimmed to allow for tap hole installation if mixer is mounted on sink.

CLEATS: Place cleats that are cut to size on the inside edge of the sink apron. The cleats allow for the sink to be easily installed onto the cupboard.

unto

Silicone Sealant

FIXING SCREWS: Use fixing screws, attach sink to cupboard top. These screws attach through the edge of the cupboard to the cleat fixing sink firmly onto cupboard top.

Pencil

Silicone Sealant

Jigsaw

Drill - 9mm or larger bit

Flashlight

Nut Driver - 9mm (3/8â&#x20AC;?)

G-Clamps

Screwdriver - shank at least 152mm (6â&#x20AC;?)

Tape Measure

How to install SINK MIXERS * It is recommended that sink mixers be installed by a registered plumber

Ceramic disc cartridges mix best where the water pressure does not exceed 400kPa. Always plumb hot water to the left hand side and cold water to the right hand side. Ensure that the water system is balanced.

Turn off the water supply before commencing installation

Basic components are: Mixer, two flexible hoses (blue for cold and red for hot water), circular rubber gasket, fixing plate, plastic brace (when applicable), back nut & metal brace

Fix flexible hoses to the mixer by screwing flexible hoses to the base of the mixer. Note: Check that the “O” ring at the top end of each flexible hose is in position. If there is no “O” ring present the tap will leak. (flexible hoses can be screwed in by hand)

With the front of the mixer facing you, attach the hot (red) flexible water hose on the left of the brass rod and the cold (blue) flexible hose to the right.

Slip the circular rubber gasket over the flexible hoses which will sit at the base of the mixer.

Feed the flexible hoses through punched tap hole and lower the mixer onto the tap landing of the sink.

How to install SINK MIXERS

Slip 2nd rubber gasket and plastic tap brace respectively over flexible hoses from the underside of the sink.

fasten.

Slip metal brace over brass threaded rod and

(If and when supplied)

Tighten nut onto brass rod on the underside of sink until maximum tension is reached. The mixer should be firm on the sink.

11.

Remove aerator.

13.

Turn off main water supply & reinstall

aerator.

10.

Flush out the pipe then connect flexible hoses to plumbers piping.

12.

Turn on main water supply & open tap to flush any possible debris from the system.

Flashlight

Adjustable Wrenches

Pipe Wrench

Nut Driver - 9mm (3/8â&#x20AC;?)

Fault Finding - SINK MIXER Complaint Water is leaking (dripping) through the outlet

Water is leaking from the body of the Mixer

Insufficient hot / cold water from the Mixer

Cause

Damaged or dirty Cartridge

Solution Clean the Cartridge Replace the Cartridge

Cartridge “O” Ring damaged

Replace Cartridge “O” Ring

Cartridge not sitting securely

Reposition and secure the Cartridge

Loose Cartridge Retaining Nut

Tighten the Cartridge Retaining Nut

Dirt in the Regulating Valve

Clean the Regulating Valve

Dirt in the Mixer or Aerator

Clean the Mixer and Aerator

How to change a SINK MIXER CARTRIDGE

* It is recommended that sink mixer cartridges be changed by a registered plumber NOTE:- All the following service operations can be performed without removing the tap from its installation mountings. CAUTION:- Before servicing or repairing any part of a tap ISOLATE all water supplies to the tap to prevent damage to property from flooding or injury by scalding with hot water to bodily parts.

CARTRIDGE: Features: • • • • •

Noise suppressor of 17-18 decibels Anti-scold set for standard operation can be reset. (Refer to registered plumber). Endurance test of 70,000 cycles, complieswith EN 814 International Standards Reduced flow rate for green rating Suitable for balanced water pressure of 200 - 600kPa

Adjustable Wrenches

Small Flat Screwdriver

10 mm Allen Key

36mm Tube Spanner

2.5 mm Allen Key Small Phillips Screwdriver

How to change a SINK MIXER CARTRIDGE - Boston Swivel * Turn off the water supply before commencing installation

Use a small flat screw driver to remove the hot and cold indicator from its hole in the Tap Handle.

(The force required to do this will depend on the age of the Tap and the amount of contamination between the threads of the Cartridge Chamber Cover and the Cartridge Retaining Nut.)

(The force required to do this will depend on the age of the Tap and the amount of contamination between the threads of the Tap Body and the Cartridge Retaining Nut.)

Insert a 2.5mm Allan Key through the hole in Tap Handle and into the Grub Screw and loosen (turn anti-clockwise) one turn to release Tap Handle.

Firmly grip the Cartridge Cover between fingers and thumb and rotate anticlockwise to loosen and remove the cover.

Pull the Tap Handle off the Cartridge.

Hold the Tap Body firmly with one hand and using a suitable 35mm spanner, rotate the Cartridge Retaining Nut anticlockwise until it is completely free of the Tap Body.

How to change a SINK MIXER CARTRIDGE - Boston Swivel

After removing the Cartridge Retaining Nut, pull the Cartridge out of the Tap Body by pulling on the Shaft.

Before inserting the new Cartridge into the Tap Body, align the Cartridge Locating Studs with the Cartridge Locating Stud Holes in the Tap Body. This will help to locate the Cartridge correctly when it is fully inserted into the Tap Body.

The use of a pair of pliers may be necessary to help pull the Cartridge out of the Tap Body depending on the amount of grip that you can generate with your fingers.

Fully insert the Cartridge into the Tap Body and firmly push it in. Hold the Cartridge as shown above and try to rotate the Cartridge to ensure that the cartridge cannot turn. Once the Cartridge is correctly located re-assemble the Tap in the reverse order.

How to change a SINK MIXER CARTRIDGE - Razzo Swivel * Turn off the water supply before commencing installation

Using a small flat screw driver, pop the Plastic Cap from its hole under the Tap Handle

Insert a 2.5mm Allan Key through the hole under the Tap Handle and into the Grub Screw and loosen (turn anti-clockwise) one turn to release Tap Handle.

Firmly grip the Cartridge Cover between fingers and thumb and rotate anticlockwise to loosen and remove the cover.

The force required to do this will depend on the age of the Tap and the amount of contamination between the threads of the Cartridge Chamber Cover and the Cartridge Retaining Nut.

Pull the Tap Handle off the Cartridge.

Hold the Tap Body firmly with one hand and using a suitable 35mm spanner, rotate the Cartridge Retaining Nut anti-clockwise until it is completely free of the Tap Body. The force required to do this will depend on the age of the Tap and the amount of contamination between the threads of the Tap Body and the Cartridge Retaining Nut.

How to change a SINK MIXER CARTRIDGE - Razzo Swivel

After removing the Cartridge Retaining Nut, pull the Cartridge out of the Tap Body by pulling on the Shaft.

The use of a pair of pliers may be necessary to help pull the Cartridge out of the Tap Body depending on the amount of grip that you can generate with your fingers.

How to change a SINK MIXER CARTRIDGE - Flair Swivel * Turn off the water supply before commencing installation

Insert a 2.5mm Allan Key into the Grub Screw under the Tap Handle and loosen (turn anti-clockwise) one turn to release Tap Handle.

Pull the Tap Handle off the Cartridge.

Hold the Tap Body firmly with one hand and using a suitable 35mm spanner, rotate the Cartridge Retaining Nut anticlockwise until it is completely free of the Tap Body.

The force required to do this will depend on the age of the Tap and the amount of contamination between the threads of the Tap Body and the Cartridge Retaining Nut.

Remove the Chrome Disc from the Cartridge.

After removing the Cartridge Retaining Nut, pull the Cartridge out of the Tap Body by pulling on the Shaft. The use of a pair of pliers may be necessary to help pull the Cartridge out of the Tap Body depending on the amount of grip that you can generate with your fingers.

How to change a SINK MIXER CARTRIDGE - Flair Swivel

How to change a SINK MIXER CARTRIDGE - Billy Joystick Professional / Swivel * Turn off the water supply before commencing installation

Loosen the Grub Screw in the Tap Handle with a 2mm Allan Key

Remove the Handle Assembly Spring from the Cartridge.

Hold the Tap Body firmly with one hand and using a suitable 35mm spanner, rotate the Cartridge Retaining Nut anticlockwise until it is completely free of the Tap Body.

The force required to do this will depend on the age of the Tap and the amount of contamination between the threads of the Tap Body and the Cartridge Retaining Nut.

Using a small flat screw driver gently lift up the Cartridge Cover and pull off by hand.

How to change a SINK MIXER CARTRIDGE - Billy Joystick Professional / Swivel

Fully insert the Cartridge into the Tap Body and firmly push down. Hold the Cartridge and try to rotate the Cartridge to ensure that the cartridge cannot turn. Once the Cartridge is correctly located reassemble the Tap in the reverse order.

When re-fitting the Cartridge Cover ensure that the opening on the Cartridge Cover is perfectly aligned to the same profile on the Cartridge for correct operating range.

Re-fit the Handle Assembly complete with the Plastic Scuff Eliminating Ring fitted inside with the thick edge down.

Note: Make sure that the slot in the Cartridge Operating Shaft is inline with the Grub Screw before fitting the Handle onto the Cartridge and tightening the Grub Screw.

How to change a SINK MIXER CARTRIDGE - Enix Square Swivel * Turn off the water supply before commencing installation

Using a small flat screw driver or knife, pop the Plastic Cap from its hole under the Tap Handle

Insert a 2.5mm Allan Key through the hole under Tap Handle and into the Grub Screw and loosen (turn anticlockwise) one turn to release Tap Handle.

Firmly grip the Cartridge between fingers and thumb and rotate anti-clockwise to loosen and remove the cover.

The force required to do this will depend on the age of the Tap and the amount of contamination between the threads of the Cartridge Chamber Cover and the Cartridge Retaining Nut.

Pull the Tap Handle off the Cartridge.

Hold the Tap Body firmly with one hand and using a suitable 35mm spanner, rotate the Cartridge Retaining Nut anticlockwise until it is completely free of the Tap Body. The force required to do this will depend on the age of the Tap and the amount of contamination between the threads of the Tap Body and the Cartridge Retaining Nut.

How to change a SINK MIXER CARTRIDGE - Enix Square Swivel

After removing the Cartridge Retaining Nut, pull the Cartridge out of the Tap Body by pulling on the Shaft.

The use of a pair of pliers may be necessary to help pull the Cartridge out of the Tap Body depending on the amount of grip that you can generate with your fingers.

How to change a SINK MIXER CARTRIDGE - Highrise Swivel * Turn off the water supply before commencing installation

Use a small flat screw driver to remove the hot and cold indicator from its hole in the Tap Handle.

Insert a 2.5mm Allan Key through the hole in Tap Handle and into the Grub Screw and loosen (turn anti-clockwise) one turn to release Tap Handle.

Firmly grip the Cartridge Cover between fingers and thumb and rotate anticlockwise to loosen and remove the cover.

The force required to do this will depend on the age of the Tap and the amount of contamination between the threads of the Cartridge Chamber Cover and the Cartridge Retaining Nut.

Pull the Tap Handle off the Cartridge.

How to change a SINK MIXER CARTRIDGE - Highrise Swivel

After removing the Cartridge Retaining Nut, pull the Cartridge out of the Tap Body by pulling on the Shaft.

The use of a pair of pliers may be necessary to help pull the Cartridge out of the Tap Body depending on the amount of grip that you can generate with your fingers.

How to change a SINK MIXER CARTRIDGE - Cascade Professional / Prep Bowl * Turn off the water supply before commencing installation

Use a small flat screw driver to remove the hot and cold indicator from its hole in the Tap Handle.

Insert a 2.5mm Allan Key through the hole in the Tap Handle and into the Grub Screw and turn anti-clockwise once to release the Tap Handle.

Firmly grip the Cartridge Chamber Cover between fingers and thumb and rotate anti-clockwise to loosen and remove the cover.

The force required to do this will depend on the age of the Tap and the amount of contamination between the threads of the Cartridge Chamber Cover and the Cartridge Retaining Nut.

Pull the Tap Handle off the Cartridge.

Hold the Tap Body firmly with one hand and using a 35mm spanner, rotate the Cartridge Retaining Nut anticlockwise until it is free of the Tap Body. The force required to do this will depend on the age of the Tap and the amount of contamination between the threads of the Tap Body and the Cartridge Retaining Nut.

How to change a SINK MIXER CARTRIDGE - Cascade Professional / Prep Bowl

After removing the Cartridge Retaining Nut, pull the Cartridge out of the Tap Body by pulling on the Shaft.

The use of a pair of pliers may be necessary depending on the amount of grip that you can generate with your fingers.

Before inserting the new Cartridge into the Tap Body, align the Cartridge Locating Studs with the Cartridge Locating Stud Holes in the Tap Body.

How to change a SINK MIXER CARTRIDGE - Projectline Single Lever / Wall Mounted * Turn off the water supply before commencing installation

Use a small flat screw driver to remove the hot and cold indicator from its hole in the Tap Handle.

Insert a 2.5mm Allan Key through the hole in the Tap Handle and into the Grub Screw and turn anti-clockwise once to release the Tap Handle.

Firmly grip the Cartridge Chamber Cover between fingers and thumb and rotate anti-clockwise to loosen and remove the cover.

The force required to do this will depend on the age of the Tap and the amount of contamination between the threads of the Cartridge Chamber Cover and the Cartridge Retaining Nut.

Pull the Tap Handle off the Cartridge.

How to change a SINK MIXER CARTRIDGE - Projectline Single Lever / Wall Mounted

After removing the Cartridge Retaining Nut, pull the Cartridge out of the Tap Body by pulling on the Shaft.

The use of a pair of pliers may be necessary depending on the amount of grip that you can generate with your fingers.

Before inserting the new Cartridge into the Tap Body, align the Cartridge Locating Studs with the Cartridge Locating Stud Holes in the Tap Body.

Sink Mixer - Spares Matrix

How to install a WASTE DISPOSER * It is recommended that the waste disposer be installed by a registered plumber

Remove sink flange from waste disposal unit by loosening and unclipping the hinged clip.

Place the sink flange rubber gasket over the sink flangeâ&#x20AC;&#x2122;s threaded ring.

Insert the flange and rubber gasket into the sink waste outlet from inside the sink bowl.

Place the sink flange fibre gasket and metal ring over the sink flangeâ&#x20AC;&#x2122;s threaded ring.

Attach the mounting ring from the underside of the sink and tighten with one hand while using the other hand to press down on the sink flange.

Hand tighten as tight as possible until maximum tension is reached.

Now tighten the three screws in the mounting ring, with a Phillips Screw Driver, to lock it in place.

Remove the Waste Pipe Flange and screws with the supplied Allen Key.

How to install a WASTE DISPOSER

10.

11.

12.

13.

14.

Insert the Waste Pipe into the Waste Outlet, ensuring that the Waste Pipe is pointing downwards at 90 degrees.

Slide the Waste Pipe Flange onto the Waste Pipe.

Fix the Waste Pipe Flange to the Waste Disposer by replacing the screws.

Before mounting the food disposer, ensure that the rubber splash guard is in place.

Using two hands push the disposer upwards so that the inner groove on the splash guard locks onto the sink flange.

Place the hinged clamp around the splash guard and lock in place.

* Hint â&#x20AC;&#x201C; use cooking oil to lubricate the inner rim of the splash guard.

15.

Now that the disposer is engaged it will hang freely. Connect the Waste Pipe to the Spazi Plumbing Kit ensuring the Trap is below the Waste Disposer connection point.

Phillipâ&#x20AC;&#x2122;s Screw Driver Allen Key (supplied)

Flashlight

How to install a WASTE DISPOSER AIR SWITCH Purpose: The air switch allows for easy operation of the waste disposal unit. It eliminates the inconvenience of one from accessing the disposal unit from inside the cupboard to switch it on.

Insert the clear flexi pipe to the base of the air switch.

Insert the free end of the clear flexi through the pre punched 30mm tap hole in the sink.

Thread back nut over flexi pipe on the underside of the sink and screw onto back end of air switch to secure against sink.

The free end of the flex pipe is pushed on to the side of the electrical box.

Turn on the electricity.

Operate the switch by pushing down the button.

Flashlight Pipe Wrench Adjustable Wrenches

How to install a SPAZI F1 SINGLE BOWL

Spazi F1 Assembly Parts 1 2 3 4 2 3

Trap Assembly 3 2

7 8

Horizontal Pipes 2 11

2 3

Vertical Pipes

How to install a SPAZI F1 SINGLE BOWL No.

Qty Included

Part

Dome Pipe Cover

Hand Tightening Joint

Green Compression Ring

“L” Shaped Pipe

Trap

Horizontal Pipe

Rubber Gasket

Fixed Hand Tightening Joint

Green Auxiliary Connection

Vertical Pipe

Green End Cap

INCLUDED : 50mm - 40mm Female Adapter For use where a 50mm Plumbed Drain Pipe is used.

Marking Pen

Hack Saw

Tape Measure

Flashlight

How to install a SPAZI F1 SINGLE BOWL * 1. 2. 3. 4. 5. 6. 7. 8.

It is recommended that waste fittings be installed by a registered plumber Place a Hand Tightening Joint {2} and Green Compression Ring {3} on the “L” Shaped Pipe {4}. ush the “L” Shaped Piped {4} into the short end of the Trap {5}, as far as it will P go, and turn the Hand Tightening Joint {2} on to the thread. Measure and cut the plumbed drain pipe to the minimum length of 70mm. (This length is just a guide - measure the pipe in relation to the position of the Spazi kit from the wall) Place the Dome Pipe Cover {1}, a Hand Tightening Joint {2} and Green Compression Ring {3} on the Plumbed Waste Pipe. Push the Plumbed Waste Pipe into the “L” Shaped Pipe, as far as it will go, and turn the Hand Tightening Joint onto the thread. Place a Hand Tighening Joint {2} and Green Compression Ring {3} on the Horizontal Pipe {6}. Place the Rubber Gasket {7} inside the Fixed Hand Tightening Joint {8} of the Horizontal Pipe and turn the Fixed Hand Tightening Joint on to the thread of the waste fitting. Place a Hand Tighening Joint {2} and Green Compression Ring {3} on the Vertical Pipe {10}. Insert the Green Auxiliary Connection {9} into Hand Tightening Joint {2} and connect to the top of the Vertical Pipe. * When connecting a washing machine / dish washer, trim the Green Auxiliary Connection {9} before connecting the outlet pipe. (NOTE: If neither a washine machine nor dish washer are being connected, the Green Auxiliary Connection {9} must be replace with a Green End Cap {11})

9. 10. 11. 12. 13. 14. 15. 16. 17.

Push the Vertical Pipe onto the Horizontal Pipe and line the Vertical Pipe up with the Trap. Using the marking pen, mark the required length of the Vertical Pipe to fully interlock with the Trap. Remove the Vertical Pipe from the Horizontal Pipe and cut it to the required length with the hack saw. Push the Vertical Pipe into the Trap, as far as it will go, and turn the Hand Tightening Joint onto the thread. Line the Horizontal Pipe up with the Vertical Pipe. Using the marking pen, mark the required length of the Horizontal Pipe to fully interlock with the Vertical Pipe. Disconnect the Horizontal Pipes from the Waste Fitting and cut it to the required length with the hack saw. Push the Horizontal Pipe onto the Vertical Pipe, as far as it will go, and turn the Hand Tightening Joint onto the thread. Ensure the Rubber Gasket is inside the Fixed Hand Tightening Joint of the Horizontal Pipe and turn the Fixed Hand Tightening Joint on to the thread of the waste fitting. Once the installtion is complete, check all the connections for leaks.

4 min

70m

4 2 3

Sink

Waste Fitting

2 9 Sink

10 2 3

Sink

2 3

How to install a SPAZI F2 DOUBLE BOWL

Spazi F2 Assembly Parts 1

6 7 4

8 1

1 9

1 4

Manifold Assembly 4 1

11 12

Horizontal Pipes

1 4

Vertical Pipes

How to install a SPAZI F2 DOUBLE BOWL No.

Qty Included

Part

Hand Tightening Joint

Green Auxiliary Elbow Connection

Manifold

Green Compression Ring

Trap

Green End Cap

Green Auxiliary Connection

Dome Pipe Cover

“L” Shaped Pipe

Horizontal Pipe

Rubber Gasket

Fixed Hand Tightening Joint

Vertical Pipe

INCLUDED : 50mm - 40mm Female Adapter For use where a 50mm Plumbed Drain Pipe is used.

Marking Pen

Hack Saw

Tape Measure

Flashlight

How to install a SPAZI F2 DOUBLE BOWL * 1. 2. 3. 4. 5. 6. 7. 8.

It is recommended that waste fittings be installed by a registered plumber Place a Hand Tighening Joint {1} and Green Compression Ring {4} on the base of the Manifold {3}. Place a Hand Tightening Joint {1} and Green Compression Ring {4} on the “L” Shaped Pipe {9}. Push the base of the Manifold {3} into the long side of the Trap {5}, as far as it will go, and turn the Hand Tightening Joint {1} on to the thread. ush the “L” Shaped Piped {9} into the short end of the Trap {5}, as far as it will P go, and turn the Hand Tightening Joint {1} on to the thread. Measure and cut the plumbed drain pipe to the minimum length of 70mm. (This length is just a guide - measure the pipe in relation to the position of the Spazi kit from the wall) Place the Dome Pipe Cover {8}, a Hand Tightening Joint {1} and Green Compression Ring {4} on the Plumbed Waste Pipe. Push the Plumbed Waste Pipe into the “L” Shaped Pipe, as far as it will go, and turn the Hand Tightening Joint onto the thread. Insert the Green Auxiliary Elbow Connection {2}, Green Auxiliary Connect {7} and Green End Cap {6} into Hand Tightening Joints {1} and connect to the two (2) side opening and centre opening of the Manifold. * When connecting a washing machine / dish washer, trim the Green Auxiliary Elbow Connection {2} before connecting the outlet pipe. (NOTE: If neither a washine machine nor dish washer are being connected, the Green Auxiliary Elbow Connection {2} must be replace with a Green End Cap {6})

9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21.

Place a Hand Tighening Joint {1} and Green Compression Ring {4} on the Horizontal Pipe {10}. Place the Rubber Gasket {11} inside the Fixed Hand Tightening Joint {12} of the Horizontal Pipe and turn the Fixed Hand Tightening Joint on to the thread of the waste fitting. Place a Hand Tighening Joint {1} and Green Compression Ring {4} on the Vertical Pipe {13}. Push the Vertical Pipe onto the Horizontal Pipe and line the Vertical Pipe up with the Manifold Assembly. Using the marking pen, mark the required length of the Vertical Pipe to fully interlock with the Manifold. Remove the Vertical Pipe from the Horizontal Pipe and cut it to the required length with the hack saw. Push the Vertical Pipe into the Manifold, as far as it will go, and turn the Hand Tightening Joint onto the thread. Line the Horizontal Pipe up with the Vertical Pipe. Using the marking pen, mark the required length of the Horizontal Pipe to fully interlock with the Vertical Pipe. Disconnect the Horizontal Pipe from the Waste Fitting and cut it to the required length with the hack saw. Push the Horizontal Pipe onto the Vertical Pipe, as far as it will go, and turn the Hand Tightening Joint onto the thread. Ensure the Rubber Gasket is inside the Fixed Hand Tightening Joint of the Horizontal Pipe and turn the Fixed Hand Tightening Joint on to the thread of the waste fitting. Repeat steps 9 - 19 for the remaining waste outlets / Waste Fittings. Once the installtion is complete, check all the connections for leaks.

min

70m

6 1

Sink

Waste Fitting

Sink

1 4

Sink

How to install a SPAZI F3 TRIPLE BOWL

Spazi F3 Assembly Parts 1 2 7 4

8 1 1 9

1 4

Manifold Assembly 4 1

11 12

Horizontal Pipes

1 4

Vertical Pipes

How to install a SPAZI F3 TRIPLE BOWL No.

Qty Included

Part

Hand Tightening Joint

Green Auxiliary Elbow Connection

Manifold

Green Compression Ring

Trap

Green End Cap

Green Auxiliary Connection

Dome Pipe Cover

“L” Shaped Pipe

Horizontal Pipe

Rubber Gasket

Fixed Hand Tightening Joint

Vertical Pipe

INCLUDED : 50mm - 40mm Female Adapter For use where a 50mm Plumbed Drain Pipe is used.

Marking Pen

Hack Saw

Tape Measure

Flashlight

How to install a SPAZI F3 TRIPLE BOWL * 1. 2. 3. 4. 5. 6. 7. 8.

9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21.

min

70m

2 1

Sink

Waste Fitting

Sink

1 4

Sink

How to install a WASHTROUGH

+- 600

600

Insert the M8 bolt shafts into each hole.

Hand tighten the top bolts into place.

Determine the position of the Washtrough from the floor. Using a spirit level, draw a line above the wash trough. (600mm appart and recommended height of +-600mm)

With the brackets in position, mark the hole positions through the brackets holes, on to the wall.

Remove the brackets and drill the holes for the bolt shaft where the brackets marking were made. (The hole diameter is dependant on the bolts used)

Align the brackets on the wall and insert the top bolts on each bracket.

How to install a WASHTROUGH

10.

11.

12.

Tilt the brackets inwards and remove the double sided tape.

Push the brackets outwards so that the double sided tape sticks to the inside of the apron of the Washtrough.

Drop the Washtrough onto the brackets.

Place the remaining bolts into the brackets.

Tighten all the bolts into place with a spanner, securing the Washtough to the wall.

plumbed.

The Washtrough is now ready to be

Pencil

Adjustable Wrenches

Hammer

Drill - 9mm or larger bit

Tape Measure

Screw Driver - shank at least 152mm (6â&#x20AC;?)

CLEANING AND MAINTENANCE

Inox Cream 250g Tube Cleans, Shines, Polishes And Revitalises Stainless Steel.

Product Code: 1120047 CLEANING PROCEDURE Clean the Stainless Steel as often as experience dictates (i.e. when noticeably dull or dirty) and use the simplest cleaning procedure that will effectively “do the job”. -- Stainless Steel reacts best to clean water or mild detergent solution, applied with a soft cloth or sponge, rinsed well and wiped dry. -- Routine, simple, gentle and inexpensive cleaning will retain both the corrosion resistance and appearance of Stainless Steel through years of exposure and use. Occasionally a small amount of Inox Creme may be used on a soft, damp cloth with the detergent solution to remove stubborn dirt or slight incipient stains. Rub gently. CLEANING DO’S -- Employ regular routine cleaning rather than an occasional aggressive single cleaning. -- Only use propriety brands of cleaners that state “SUITABLE FOR STAINLESS STEEL”, such as Inox Creme -- Always rinse and dry as the final step in a cleaning procedure. CLEANING DON’TS Do not use coarse abrasive powders. Do not use metallic scourers or brushes with metal bristles. Do not use the so termed “silver cleaners”. Do not use acids (except nitric acid in specific instances).

-----

STORAGE OF PRODUCTS Product research has proven that certain household products which may be stored underneath a sink, can lead to damage of the sink’s base. Chlorine is the major culprit and can be found in: chlorine for swimming pools; household bleach; bathroom cleaning products such as toilet cleaners, mildew treatments and tile cleaners; kitchen cleaning products - especially liquid cleaners; powders for dishwashers and laundry detergents. Preserve the life and beauty of your sink by storing these products away from the sink area in a well ventilated cupboard that is preferably child-proof.

Page 37

Warranties STAINLESS STEEL DOMESTIC KITCHEN SINKS: 25 years against corrosion from date of purchase (*except SA94 sink). STAINLESS STEEL SA94 SINK: 24 months against manufacturing defects. ACCESSORIES (Waste Fittings, Cutting boards, Baskets etc): 12 months against manufacturing defects. WASTE DISPOSERS: 12 months against manufacturing defects. KITCHENETTES: 12 months against manufacturing defects. KITCHEN SINK MIXERS: Body â&#x20AC;&#x201C; 5 years against manufacturing defects; Cartridge - 24 months against manufacturing defects. ECONOMY WASH TROUGH AND ECONOMY PREPARATION BOWL: 12 months against manufacturing defects. Find our full Franke Kitchen Systems Warranty Policy on our Kitchen Systems website www.franke.co.za under Support.

25 YEAR WARRANTY ON STAINLESS STEEL DOMESTIC SINKS

0861 372 653 (Option 2 for Warranty, then option 2 again for Kitchen Systems) KS-aftersales.za@franke.com 50

FRANKE KITCHEN SYSTEMS (PTY) LTD CALL CENTRE Tel 0861 372 653 Fax 0866 592 073 callcenter.fsa@franke.com www.franke.co.za

DURBAN 1194 South Coast Road, Mobeni, Durban, 4092. South Africa Tel +27 31 450 6300 Fax +27 31 450 6304

GAUTENG 77 Roan Crescent, Sage Corporate Park North, Old Johannesburg Road, Midrand, 1682 South Africa

CAPE TOWN Unit 1, Gold Street, Northgate Business Park, Northgate Estate, Cape Town, 7405 South Africa

DISCLAIMER The information and dates supplied in this brochure are based on the information believed to be reliable, however are not binding and inaccuracies may occur. Franke reserves the right to change Specification and design at any time without notice. ÂŠ 2015 by Franke Kitchen Systems (Pty) Ltd. All rights reserved under the Copyright Act of 1987 with the amendments. Reproduction of any of the content, full or partial, is allowed only with prior written approval of Franke Kitchen Systems (Pty) Ltd. No reasonable requests will be refused provided the conditions as laid out are met.