DUMPS BASE
EXAM DUMPS
HUAWEI H31-341
28% OFF Automatically For You HCIP-Transmission V2.0
1. Which of the following description of the ASON software structure is correct? (Multiple Choice) A. Intelligent optical network consists of three planes B. Management plane mainly refers to upper management such as network management C. Intelligent software main application management plane D. The transmission plane refers to the traditional transmission network. Answer: ABD
2. The transmission plane mainly performs functions such as optical signal transmission, multiplexing, configuration protection switching, and reconnection, and ensures the reliability of the transmitted optical signal. However, the exchange action of this layer is carried out under the influence of the management dry surface and the control plane. A. TRUE B. FALSE Answer: A
3. Which of the following are limitations of the alarm and performance analysis methods? (Multiple Choice) A. Field maintenance personnel cannot understand the current operating condition of the equipment. B. The network administrator cannot obtain the current notifications of the device, the alarm occurrence time, and the historical alarm of the device. C. When some faults occur, there may be no obvious alarms or performance events reported, and sometimes no alarms or performance events are found. D. In the case of complex networking, service, and fault information, many alarms and performance events may occur along with the occurrence of faults. Due to too many reports and performance events, maintenance personnel are unable to analyze. Answer: CD
4. Which of the following is the data that needs to be collected and saved in the event of a failure? (Multiple Choice) A. Equipment alarms and performance events B. Running status data of the NE and the board C. Operation log of the network management D. Configuration data of the NE and the board Answer: ABCD
5. After the signal of the standard Ethernet frame length of 64 Bytes is connected to the Ethernet board, if the QinQ function is enabled, what is the actual frame length of the signal inside the board? A. 64 Bytes B. 84 Bytes C. 68 Bytes D. 80 Bytes Answer: C
6. The length range of the DATA field in the Ethernet frame structure is (). A. 46-1500 bytes B. 46-1518 bytes C. 64-1518 bytes D. 64-1500 bytes Answer: A
7. Which of the following is a good way to avoid creating discrete paths? (Multiple Choice) A. The path with the protected route is to be broken or switched. Ensure that the configuration is complete and standardized. B. Try to use the path function to configure. C. Guide users to learn business configuration specifications. D. The service of the single-station configuration should perform path search on the network to ensure that the service configuration is complete and standardized. Answer: ABCD
8. Which of the following description of discrete services is correct? (Multiple Choice) A. For the cross-connections, after a path search, either a discrete service or forming a path with other cross-connections, which is impossible to be a discrete service, and forming a path with other cross-connections. B. Perform path search on the U2000 network management. Cross-connections that do not form a path are called high-bandwidth services. C. Discrete service management requires the U2000 license to have path management functions. D. A service is searched for a discrete service, indicating that the service is not working properly on the NE side. Answer: AC
9. Which step is more when the the single board replacement operation of main
control board single configuration than main control board double configuration? A. Download the original configuration data B. Ensure that the version of the host software is the same before and after the replacement. C. Consistency check of network management and network element data. D. Query the alarm of the board and confirm that the original alarm has been cleared. Answer: A
10. The main application scenarios for board compatible replacement are (). (Multiple Choice) A. Expanding the board B. Change the board ID C. Change the board IP D. Replacement board Answer: ABD
11. Which of the following operating modes does the AT8 board support? (Multiple Choice) A. Reverse 2E2M B. 2E2M C. 1E1M D. Reverse 1E1M Answer: ABC
12. Which of the following description of the extended ECC is correct? (Multiple Choice) A. Extended ECC recommends to use manual basis, which reduces mutual negotiation between network elements. B. The scale of the extended ECC network (the sum of the server and the client) must not exceed 8. C. Extended ECC is divided into automatic extended ECC and manual extended ECC. One network element can only support one mode at the same time. These two methods cannot be directly docked. D. In the automatic extended ECC mode, you need to connect the Ethernet ports of the two NEs with a direct-connected network cable (or a standard network cable through B), extend the ECC, and specify the server and client. Answer: ABC
13. Which of the following description of the principle of automatic protection
switching of the standard SSM protocol is correct? (Multiple Choice) A. The network element broadcasts the clock quality information of the synchronization source to the downlink site through the s1 byte. And reverse notice the uplink site by the S1 byte in the direction of the synchronization source that the clock quality from the local network element is "not available for synchronization". B. If there are multiple clock sources with the highest quality level, the network element selects the clock with the highest clock priority as the synchronization source. C. According to the clock source priority table, the network element first selects the clock with the highest quality level from the available clock sources as the synchronization source. D. The network element broadcasts the clock quality information and the clock source ID of the synchronization source to the downlink site through the S1 byte, and reverse notices the uplink site that the clock quality from the local network element is "not available for synchronization" by the S1 byte in the direction of the synchronization source. Answer: ABCD
14. Which of the following description of the evolutionist in the mainstream SDN model in the industry is correct? (Multiple Choice) A. Control flexibility is moderate and open is not complete B. Make full use of existing equipment and achieve fast C. Device programmable, open northbound API interface D. Try to preserve and reuse existing routing protocols and IP network technologies Answer: ABCD
15. Which of the following statement about the MPLS-TP OAM level is correct? A. Section is the service layer of the tunnel, Tunnel is the service layer of the PW, and PW is the service layer of the Service. B. Section is the service layer of PW, PW is the service layer of Tunnel, and Tunnel is the service layer of Service. C. Service is the service layer of the PW, PW is the service layer of the Tunnel, and Tunnel is the service layer of the Section. D. Tunnel is the service layer of PW, PW is the service layer of Service, and Service is the service layer of Section. Answer: A
16. Which of the following is the incorrect description of the internal port properties of the Ethernet board? A. For the ingress port for the Access attribute, if the input data carries the VLAN ID, discard.
B. For the inbound port of the Tag Aware attribute, if the input data carries the VLAN ID, transparently receive the data. C. For the ingress port of the Access attribute, if the input data does not carry the VLAN ID, it is directly transparent. D. For the ingress port of the Tag Aware attribute, if the input data does not carry the VLAN ID, discard. Answer: C
17. The steps that must be performed when configuring the Ethernet private line service carried by the PW are as follows: (Multiple Choice) A. Configure QoS B. Configure MPLS tunnel C. Configure port DCN D. Configure the UNI port Answer: BCD
18. MPLS APS is a network protection mechanism that implements service creation through the detection function of MPLS OAM. A. TRUE B. FALSE Answer: A
19. The E-Line service types supported by the MS-OTN packet device are: (Multiple Choice) A. E-Line service based on VL.AN B. E-Line service based on QinQ C. E-Line carried by PW D. Point-to-point transparent transmission of E-Line services Answer: ABCD
20. Which of the following are the components of general package format of PWE3? (Multiple Choice) A. Type B. CW (Control Word) C. MPLS label D. Payload Answer: BCD
GET FULL VERSION OF H31-341 DUMPS
Powered by TCPDF (www.tcpdf.org)