HKH Light duty metal anchors Hollow deck anchor Anchor version
Benefits
HKH (M6-M10)
- Anchor for suspended ceilings and overhead support applications - Channel installation - Optical setting control
Base material
Load condition
Prestressed hollow core slabs
Fire resistance
Other information
Corrosion resistance
Sprinkler approved
Approvals / certificates Description Allgemeine bauaufsichtliche Zulassung (national approval in Germany for a single point fastening) a) Fire test report Assessment report (fire) Sprinkler a)
1
Authority / Laboratory
No. / date of issue
DIBt, Berlin
Z-21.1-1722 / 2011-10-31
IBMB, Braunschweig warringtonfire VdS, Cologne
UB 3606 / 8892 / 2002-07-22 WF 327804/A / 2013-07-10 G 4961028 / 2006-09-05
All data given in this section according DIBt Z-21.1-1722, issue 2011-10-31.
Updated: Feb-18
Basic loading data All data in this section applies to: Correct setting (See setting instruction) No edge distance and spacing influence Hollow decks where bH ≤ 4,2. bst Hollow decks, classification ≥ C 45/55 Concrete fcc≥50 N/mm2
Recommended loads Anchor size M6 M8 M10 M6 Cavity to surface thickness db [mm] > 25 For a single anchor [kN] Tension Frec 0,7 0,7 0,9 0,9 For a group of two anchors with a spacing s ≥ 100 mm and 200 mm [kN] spacing s ≥ 100 mm 0,9 0,9 1,2 1,2 Tension Frec [kN] spacing s ≥ 200 mm 1,1 1,1 1,5 1,5 For a group of four anchors with a spacing s ≥ 100 mm and 200 mm spacing s ≥ 100/100 mm [kN] 1,2 1,2 1,6 1,6 [kN] Tension Frec spacing s ≥ 100/200 mm 1,5 1,5 2,0 2,0 spacing s ≥ 200/200 mm [kN] 1,9 1,9 2,5 2,5
M8 > 30
M10
M6
M8 > 40
M10
0,9
1,2
2,0
2,0
3,0
1,2 1,5
1,6 2,0
2,5 3,3
2,5 3,3
4,0 5,0
1,6 2,0 2,5
2,1 2,6 3,3
3,5 4,4 5,5
3,5 4,4 5,5
5,3 6,6 8,3
The given loads are valid for tension load, shear load and all load directions.
Materials Mechanical properties Anchor size Nominal tensile strength
fuk
Admissible bending resistance
Material quality Part All parts
[N/mm²] [Nm]
M6 800 700 7,0 4,9
M8 500 700 10,7 12,1
M10 500 700 21,4 24,1
M6 < 10 0 10 9,8 86
M8 < 10 0 10 11,8 88 55
M10 < 10 0 10 13,8 93
Material HKH (Carbon steel) HKH (Stainless steel)
Anchor dimension Anchor size Thickness of fixture Length of the spacer sleeve Length of the part of the sleeve Anchor diameter Length of the bolt Length of the part of the sleeve
Updated: Feb-18
Carbon steel Stainless steel Carbon steel Stainless steel
Galvanised to min. 5 µm Stainless steel A4
tfix l1 lh1 d l lh
[mm] [mm] [mm] [mm] [mm] [mm]
2
Setting information Setting details Anchor size Diameter of clearance hole in the fixture Embedment depth for HKH Torque moment Width across
df ≤ hs Tinst SW
[mm] [mm] [Nm] [mm]
Installation equipment Anchor size Drill bit Rotary hammer Setting tools Machine setting tool
M6 12 5 10
M8 14 55 to 65 10 13
Edge distance a)
c≥ cmin ≥
[mm] [mm]
M8 150 100
Spacing between outer anchors of neighbouring fixation
a≥
[mm]
300
3
20 17
M6 M8 M10 TE-CX-10 TE-CX-12 TE-CX-14 TE 6A, TE 6C, TE 6S, TE 15, TE 15-C, TE 18-M Torque wrench available
Setting parameters Anchor size
a)
M10 16
M6
M10
For edge distance < 150 mm the recommended load has to be reduced with F=0,75. Frec.
Updated: Feb-18
Setting instruction *For detailed information on installation see instruction for use given with the package of the product. Setting instruction 1. Drill the hole 2. Insert the anchor 3. Setting mark must be visible
Updated: Feb-18
4