X-FCP DATA SHEET
Checker plate fastening system
April 2021
X-FCP
X-FCP Checker plate fastening system Product data Dimensions X-FCP-R 5/10
1
Material specifications See fastener selection for more details.
X-FCP-F 5/10
1
Recommended fastening tools
• See fastener program in the next pages.
HILTI
1
HILTI
2
10
2
1,25
10 o 45
o 45
Approvals LR: X-FCP ABS, LR: X-FCP-R ABS: X-FCP-F • N ot all information presented in this product data sheet might be subject to approval / certificate content. Please refer to approval / certificate for further information.
X-CRM8-15-12 FP10 Ø8 [0.315"]
X-ST-GR M8/5 P8
ɿ8
o 10
9 12 [0.354"] [0.472"] 25 [0.894"]
9
Lg
12.5
12.5 25
[0.315"]
30
Ø8
X-ST-GR M8/10 P8
X-CRM8-9-12 FP10
X-CRM8-15-12 P8 M8 o 4
ૃ
.
o8
M8
ૃ 14 12 [0.551"] [0.472"] 30 [1.181"]
04/2021
X-CRM8-9-12 P8 M8 ɿ4
M8 o 4
M8
X-FCP Sealing ring
www.hilti.group
Lg
12.5 30
2
X-FCP Application Checker plate
Application areas for X-FCP system X-FCP-R • Marine, offshore, petrochemical, caloric (coal, oil) power plants, etc. • Not for use in automobile tunnels, swimming pools or similar environments. X-FCP-F • Indoors, mildly corrosive environment, or for limited lifetime use. • Not for use in marine atmosphere or in heavily polluted environment. Sealing ring • Drip-through of water/oil needs to be prevented. Performance data Recommended resistance under tension load Nrec = 1.8 [kN]
• Limited by the strength of the X-CRM8 and X-ST-GR threaded stud. • Recommended loads are valid for fastenings of steel and aluminium with 20 mm pre-drilling. • X-FCP-F and X-FCP-R are not intended for shear loading. Application recommendation Fastened material thickness
X-CRM8 , X-ST-GR
Thickness of checker plates: tI ≅ 5.0–13.0 mm
tII
Base material thickness
Steel thickness: tII ≥ 6 mm
3 04/2021 www.hilti.group
X-FCP Fastener positioning in base material X-CRM8, X-ST-GR c
c
s
s
Edge distances: c ≥ 15 mm Spacing: s ≥ 15 mm
Application limits for X-CRM8 DX 76, DX 76 PTR Steel thickness, tII [mm]
20
tII ≥ 6 mm
18 16
2
14 12 10
1
① Fastener: X-CRM8-__-12 FP10 / Tool type: DX 76 (impact) ② Fastener: X-CRM8-__-12 FP10 / Tool type: DX 76 (co-acting)
8 6
S235Jxx S275Jxx
S355Jxx 450 500 550 600 650 Steel strength, Rm [N/mm2]
400
700
DX 6, DX 5, DX 460 Steel thickness, tII [mm]
20
tII ≥ 6 mm
18 16
2
14 12 10
1
① Fastener: Tool type: ② Fastener: Tool type:
X-CRM8-__-12 P8 / DX 6, DX 5 (impact), DX 460 X-CRM8-__-12 P8 / DX 5 (co-acting), DX 460
8 6
400
S235Jxx S275Jxx
S355Jxx 450 500 550 600 650 Steel strength, Rm [N/mm2]
700
• For co-acting operation push the fastener all the way back against the piston with a ramrod.
04/2021
www.hilti.group
4
X-FCP Application limits for X-ST-GR Tool type: DX 6, DX 5, DX 460
Tool type: DX 76 PTR
6WHHO WKLFNQHVV W,, >PP@
6WHHO WKLFNQHVV W,, >PP@
6WHHO VWUHQJWK 5P >1 PP @
6WHHO VWUHQJWK 5P >1 PP @
System recommendation • For more details, please refer to the chapter Accessories and consumables compatibility in the Direct Fastening Technology Manual (DFTM).
Threaded studs
13 16
Checker plate thickness Tools 9–13 mm DX 6, DX 5, DX 460, DX 76, DX 76 PTR 5– 8 mm DX 6, DX 5, DX 460, DX 76, DX 76 PTR 9–13 mm DX 6, DX 5, DX 460, DX 76 PTR 5– 8 mm DX 6, DX 5, DX 460, DX 76 PTR
11
5
Designation X-CRM8-15-12 X-CRM8-9-12 X-ST-GR M8/10 P8 X-ST-GR M8/5 P8
Cartridge selection and tool energy setting • Fastener setting information (e.g. cartridge recommendation, tool power level adjustment, base material properties and fastend material p roperties) and installation information (e.g. quality assurance) are part of the corresponding product data sheet for fastener. • Tool power level adjustment by setting tests on site. • Start tool energy selection with lowest recommended tool power level. • Correct according requirement from chapter quality assurance.
5 04/2021 www.hilti.group
X-FCP Material specification and coatings X-FCP-R system
Material designation Coating
① Disk X5CrNiMo17122 none
② Screw X2CrNiMo17132 none
③ Sealing ring Neoprene, black
① Disk ST2K40 BK Duplex
② Screw 9SMnPb28 K Duplex
③ Sealing ring Neoprene, black
X-FCP-F system Material designation Coating
• D uplex: 480 h Salt spray test per DIN 50021 and 10 cycles Kesternich test per DIN 50018/2.0 (comparable to 45 µm HDG steel).
X-ST-GR Shank P558 (CrMnMo ally) none
Threaded sleeve A4 (AISI316) none
Material designation
Shank Stainless steel wire, CR 500 (A4 / AISI316)
Coating
none
Threaded sleeve X2CrNiMo17132 X5CrNiMo17122+2H (A4 / AISI316) none
Material designation Coating X-CRM8
04/2021
www.hilti.group
6
X-FCP Quality assurance Fastening inspection X-CRM8-9-12
X-CRM8-15-12
hNVS = 12.0–15.0 mm
hNVS = 17.0–20.0 mm
X-ST-GR
X-ST-GR M8/5 P8, hNVS = 12.0–15.0 mm X-ST-GR M8/10 P8, hNVS = 17.0–20.0 mm
Installation Plates must be pre-drilled or pre-punched
Tighten the disk
o 18-20 mm
Tightening tool: • Screwdriver with torque release coupling (TRC) • S-NSX 2.8 x 15 bit
SB 12
25
mm
25
mm
Tightening torque Trec = 5–8 Nm
T = 5 - 8 Nm
Hilti Torque Screwdriver setting SF 120-A TRC 5.5–7 SF 150-A TRC 8–9
Hilti Torque tool X-BT 1/4” 7 04/2021 www.hilti.group
X-FCP Fastener program
Item no. and description Designation X-FCP-R X-FCP-F
04/2021
Item no. 308860 308859
Description Checker plate Checker plate
www.hilti.group
8