HALE HAMILTON
®
Clean Gas Products
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
Clean Gas Products HP - High Purity & UHP - Ultra High Purity HP50, HP/UHP100T, HP/UHP1100, HP/UHP1400, Regulators HP/UHP1550, UHP1600 & HP/UHP1700 CFPR & CFPM High Flow Regulators HP/UHP3600 Diaphragm Stop Valves HP2000 Series Sealed Spindle Stop Valves CFASV Bellows Stop Valves HP/UHP10 Non-return Valves CFRVS & CFLRV Relief Valves UHP30 Vacuum Generator Panels
We design, machine, build and test all our products on one site in Uxbridge. If you don’t see what you want in our standard ranges, contact us and we’ll do our best to meet your needs.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
HP/UHP
®
Spring-Loaded Regulator
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company Description HP (High Purity) and UHP (Ultra High Purity) products are for service where the product must be kept free of contamination. The design is kept simple to minimise “dead” areas where contaminants might collect. Elastomers are not used and polymers are carefully selected for suitability. UHP uses the same design as HP but the parts are machined to a better surface finish to improve cleanliness. The valve is assembled in a clean room and is Helium leak tested by mass spectrometer. HP/UHP products may be used on reactive, corrosive and/or toxic products. Special materials are available for resistance to particularly aggressive chemicals. We offer a range of spring-loaded regulators that provide a flow of gas at controlled pressure. The outlet pressure is set by turning the control knob. The process fluid is isolated from the spring compartment by a metal diaphragm. The range of outlet pressure is set by the diameter of the diaphragm and the strength of the spring. The outlet pressure is substantially unaffected by flow rate but it does drop slightly as the inlet pressure is increased. A back pressure variant is available. This controls the inlet pressure by venting pressure to the outlet if the inlet pressure exceeds the set value.
Standard Types
Build Standards (UHP only)
• •
•
• • • • •
HP50 – back pressure regulator HP/UHP100T – forward pressure regulator with tied diaphragm for low pressure HP/UHP1100 – high flow forward pressure regulator HP/UHP1400 - forward pressure regulator for low absolute pressure HP/UHP1550 - low flow forward pressure regulator UHP1600 – forward pressure regulator with no valve lift spring HP/UHP1700 – two stage forward pressure regulator
• • • •
•
Built to ultra high purity standards in a dedicated clean room facility. Ra 10 to 15 micro inch finish on wetted surfaces. Final assembly and testing is carried out under class 10 conditions. Each valve is tested for leakage using a mass spectrometer. Leak rate is less than 10-9 mbar l/s of Helium, inboard, outboard and across seat. No lubrication is used in the flow path and the seat materials are chosen for minimal gas absorption.
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
HP/UHP
®
Spring-Loaded Regulator
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company Standard Specification • •
Ports: 1/4” NPT female for HP, 1/4” Cajon VCR fittings on welded stubs for UHP (except where stated otherwise) Temperature range: -40 to +100°C
Options • • • • • • •
See next page for specification of individual types
• • • •
Ports: alternative port configurations can be supplied including additional ports for gauges and relief valves. Materials: suitable combinations of materials can be supplied for various applications such as Oxygen service or semiconductor manufacturing. Mounting: all types have threaded mounting holes in the base but an optional threaded bonnet is available for panel mounting. The standard control knob may be replaced by a lever or by a locking cap. A maximum outlet pressure limit stop is fitted as standard but a minimum outlet pressure limit stop is available as an option Steam heated and explosion proof electrically heated variants are available. Certification: variants are available approved for use with Oxygen, for medical Oxygen service or for ATEX service. Some variants have passed adiabatic shock (BAM) tests.
Panel Mounting and Locked Output Pressure
• • • • • • • • • • • •
Alternative materials can be supplied
Body: Stainless Steel or Brass Valve: Stainless Steel, Monel or Hastelloy Valve Seat: PCTFE Diaphragm: Stainless Steel (PTFE coating optional) or Hastelloy
Ordering Information
Please contact us for details
Locked Outlet Cap (Option)
Standard Materials
Please supply the following information when ordering
Cleanliness level Inlet Pressure Outlet pressure range Forward or back pressure Flow medium Tied diaphragm (where available) Control knob or locked output (state required outlet pressure) Panel mounting required Internal limit stops – state maximum pressure Port configuration Operating and storage temperature ranges Certification and QA requirements
Lever Control and Outlet Limit Stops
Panel Mounting (Option)
Operating Lever (Option) Maximum Limit Stop (Standard) Minimum Limit Stop (Option)
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
HP50 Back Pressure Regulator
HP/UHP Spring-Loaded Regulator Typical Dimensions Ø54
Specification
Ø32 13 (200)
123
Inlet Pressure bar (psi)
•
Maximum inlet pressure: 17bar (250psi) Outlet pressure ranges: 0 to 2 bar (0 to 30psi), 0 to 7 bar (0 to 100psi), 0 to 17 bar (0 to 250psi) Flow factor (Cv): 0.12
HP50
11 (160)
Increasing Flow
8.2 (120)
Decreasing Flow
5.5 (80)
0
2
4
6
8
17
• •
in mm except where shown otherwise
10
Flow l/min
Ø45
HP/UHP100T
Typical Dimensions
in mm except where shown otherwise
Specification • • •
Maximum inlet pressure: 207bar (3000psi) Outlet pressure ranges: 0 to 1.7 bar (0 to 25psi), 0 to 3.4 bar (0 to 50psi), 0 to 7 bar (0 to 100psi), 0 to 10 bar (0 to 150psi) Flow factor (Cv): 0.16 Inlet Pressure 2000psi 1000psi 500psi 200psi
136
HP100T
Ø70
6.9 (100)
5.5 (80)
18
Outlet Pressure bar (psi)
6.2 (90)
3.5 (50)
Ø51
2.7 (40) 2.0 (30) 1.4 (20) 0.7 (10) 0
40
80
120 160 Flow l/min
200
240
280
320
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
HP/UHP Spring-Loaded Regulator
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
HP/UHP1100 High Flow
Typical Dimensions
in mm except where shown otherwise
Specification
• • • •
Maximum inlet pressure: 310bar (4500psi) Outlet pressure ranges: 0 to 0.7 bar (0 to 10psi), 0 to 1.7 bar (0 to 25psi), 0 to 3.4 bar (0 to 50psi), 0 to 7 bar (0 to 100psi), 0 to 14 bar (0 to 200psi), 0 to 20 bar (0 to 290psi) Flow factor (Cv): 0.2 Process Ports: 3/8” NPT female for HP, 1/2” Cajon VCR fittings on welded stubs for UHP Pressure Variation** %: 0.6 Tied diaphragm option available HP1100
Ø66
Ø42 186
• •
Inlet Pressure 500psi 300psi 200psi
26
6.9 (100)
Outlet Pressure bar (psi)
6.2 (90)
Ø56
5.5 (80) 3.5 (50) 2.7 (40) 2.0 (30) 1.4 (20) 0.7 (10) 0
40
80
120 160 Flow l/min
200
240
280
320
** Pressure variation is the RISE in outlet pressure for a DROP in inlet pressure
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
HP/UHP1400 Absolute Pressure
HP/UHP Spring-Loaded Regulator Typical Dimensions
in mm except where shown otherwise
Specification Ø54
Ø32
Inlet Pressure
127
This regulator is for use at vacuum and low positive pressure. It includes an internal spring to compensate for ambient pressure. • Maximum inlet pressure: 10barg (150psig) • Outlet pressure range: 0.07 to 2.1 bar (1 to 30psi) absolute • Flow factor (Cv): 0.3 120psi 70psi 25psi
HP1400
19
Outlet Pressure bar (psi)
1.1 (16) 0.96 (14)
Ø58
0.83 (12) 0.69 (10) 0.55 (8) 0.41 (6) 0.27 (4) 0.14 (2) 0
14
28
42
56
71
85
100 114 128 156
Flow l/min
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
HP/UHP1550 Low Flow
HP/UHP Spring-Loaded Regulator Typical Dimensions
in mm except where shown otherwise
Specification • • • • •
Maximum inlet pressure: 376bar (5450psi) Outlet pressure ranges: 0 to 2 bar (0 to 30psi), 0 to 5 bar (0 to 75psi), 0 to 7 bar (0 to 100psi), 0 to 10 bar (0 to 150psi), 0 to 20 bar (0 to 290psi) Flow factor (Cv): 0.09 Pressure Variation** %: 0.8 Tied diaphragm option available
Ø54
Inlet Pressure
130
250 bar 100 bar 40 bar
HP1550
10 (145)
8 (116)
17
Outlet Pressure bar (psi)
9 (131)
7 (101) 6 (87)
Ø48
5 (72.5) 4 (58) 3 (43.5) 2 (29) 1 (14.5) 0
100
200
300
400
500
600
Flow l/min
** Pressure variation is the RISE in outlet pressure for a DROP in inlet pressure
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
HP/UHP Spring-Loaded Regulator
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
UHP1600 “Springless”
Typical Dimensions
in mm except where shown otherwise
Specification Ø54
120
This regulator has no spring in the process flow to eliminate the possibility of contamination from the spring. The diaphragm acts as the valve lifting spring. Because of this the diaphragm is tied to the valve mechanism. This type is only offered as ultra high purity. • Maximum inlet pressure: 218bar (3161psi) • Outlet pressure ranges: 0 to 2 bar (0 to 30psi), 0 to 7 bar (0 to 100psi), 0 to 17 bar (0 to 250psi) • Flow factor (Cv): 0.09 Inlet Pressure
17
2000psi 1000psi 500psi
HP1600
13.8 (200)
Ø46
12.4 (180)
Outlet Pressure bar (psi)
11.0 (160) 9.6 (140) 8.3 (120) 6.9 (100) 5.5 (80) 4.1 (60) 2.7 (40) 1.4 (20) 0
40
80
120 160 Flow l/min
200
240
280
320
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
HP/UHP1700 Two Stage
HP/UHP Spring-Loaded Regulator Typical Dimensions
in mm except where shown otherwise
Specification Ø54
Ø32
160
This regulator incorporates two stages of regulation in a common body. This significantly reduces the effect of changes in inlet pressure on the outlet pressure. It also reduces the cooling effect of large pressure drops. • Maximum inlet pressure: 376bar (5450psi) • Outlet pressure ranges: 0 to 2 bar (0 to 30psi), 0 to 5 bar (0 to 75psi), 0 to 10 bar (0 to 150psi) • Flow factor (Cv): 0.065 • Pressure Variation** %: 0.0064 • Tied diaphragm option available Inlet Pressure
HP1700
350 to 3000
Ø45
6.9 (100)
5.5 (80)
58
Outlet Pressure bar (psi)
6.2 (90)
4.8 (70)
Ø32
4.1 (60) 3.5 (50) 2.7 (40) 2 (30) 1.4 (20) 0.7 (10) 0
20
40
60
80
100
120
Flow l/min
** Pressure variation is the RISE in outlet pressure for a DROP in inlet pressure
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
UHP High Flow
®
Spring-Loaded Regulator
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company Description UHP (Ultra High Purity) products are for service where the product must be kept free of contamination. Elastomers and polymers are carefully selected for suitability. Parts are machined to a high surface finish to improve cleanliness. The valve is assembled in a clean room and is Helium leak tested by mass spectrometer. UHP products may be used on reactive, corrosive and/or toxic products. Special materials are available for resistance to particularly aggressive chemicals. We offer a range of spring-loaded regulators that provide a flow of gas at controlled pressure. The outlet pressure is set by turning the control knob. The process fluid is isolated from the spring compartment by a piston. The range of outlet pressure is set by the diameter of the piston and the strength of the spring. The outlet pressure is substantially unaffected by flow rate but it does drop slightly as the inlet pressure is increased. A back pressure variant is available. This controls the inlet pressure by venting pressure to the outlet if the inlet pressure exceeds the set value.
Options • • • •
Ports: alternative port configurations can be supplied including additional ports for gauges and relief valves. Materials: suitable combinations of materials can be supplied for various applications such as Oxygen service or semiconductor manufacturing. The standard control knob may be replaced by a locking cap. Certification: variants are available approved for use with Oxygen or for ATEX service.
Standard Specification • • •
Please contact us for details
See next page for specification of individual types
Process Ports: 1/2” Cajon VCR fittings on welded stubs Gauge Ports: 1/4” Cajon VCR compatible female Temperature range: -10 to +100°C
Build Standards • • •
•
Built to ultra high purity standards in a dedicated clean room facility. Ra 10 to 15 micro inch finish on wetted surfaces. Final assembly and testing is carried out under class 10 conditions. Each valve is tested for leakage using a mass spectrometer.
Standard Materials • • • •
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Alternative materials can be supplied
Body: Stainless Steel Valve: Stainless Steel Valve Seat: PCTFE O rings: Viton
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
UHP High Flow
®
Spring-Loaded Regulator
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company Please supply the following information when ordering
Ordering Information • • • • • • •
Inlet Pressure Outlet pressure range Forward or back pressure Flow medium Control knob or locked output (state required outlet pressure) Port configuration Operating and storage temperature ranges
•
Certification and QA requirements
CFPR1 Forward Pressure CFPM1 & 2 Back Pressure
Locked Output Pressure Locked Outlet Cap (Option)
Typical Dimensions
in mm except where shown otherwise
Specification CFPR1
CFPM1
CFPM2
Max. inlet pressure
320bar (4640psi)
320bar (4640psi)
25bar (360psi)
Outlet pressure ranges bar
0 to 25 0 to 100 70 to 280
0 to 10 0 to 100 100 to 250
0.5 to 2.5
Outlet pressure ranges psi
0 to 360 0 to 1450 1015 to 4060
0 to 145 0 to 1450 1450 to 3625
7 to 36
Weight: 5.5kg
231
•
Ø83
CFPR1 248 (3600)
193 (2800) 166 (2400) 138 (2000)
65
Outlet Pressure bar(psi)
221 (3200)
110 (1600) 83 (1200)
Ø95
55 (800) 28 (400) 0
5.6 (5600)
11.3 17.0 22.7 28.3 (11300) (17000) (22700) (28300) Flow nM3(l)/min
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
HP/UHP
®
Diaphragm Stop Valves
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company Description HP (High Purity) and UHP (Ultra High Purity) products are for service where the product must be kept free of contamination. The design is kept simple to minimise “dead” areas where contaminants might collect. Elastomers and polymers are carefully selected for suitability. UHP uses a similar design to HP but the parts are machined to a better surface finish to improve cleanliness. The valve is assembled in a clean room and is Helium leak tested by mass spectrometer. HP/UHP products may be used on reactive, corrosive and/or toxic products. Special materials are available for resistance to particularly aggressive chemicals. We offer a range of stop valves in which a non-tied diaphragm isolates the operating mechanism from the process fluids. The HP/UHP 3600 series is operated by a quarter turn lever or a pneumatic actuator which may be normally closed or normally open.
Construction
Build Standards (UHP only)
•
•
• •
The diaphragm is of one-piece non-welded construction for greater integrity and improved fatigue life. It acts directly on the seat to close the valve to minimise dead space and wetted area. The valve seat is mechanically supported and retained to minimise deformation under load and seat lift under reverse flow conditions. To prevent the shedding of particulate contamination, there are no sliding, rotating or rubbing components in the flow path.
• • • •
•
Standard Materials
Built to ultra high purity standards in a dedicated clean room facility. Ra 10 to 15 micro inch finish on wetted surfaces. Final assembly and testing is carried out under class 10 conditions. Each valve is tested for leakage using a mass spectrometer. Leak rate is less than 10-9 mbar l/s of Helium, inboard, outboard and across seat. No lubrication is used in the flow path and the seat materials are chosen for minimal gas absorption.
Alternative materials can be supplied
• Body: Stainless Steel, Monel or Brass • Valve: Stainless Steel or Brass
• Seat: PCTFE • Diaphragm: Hastelloy
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
HP/UHP
®
Diaphragm Stop Valves
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company Options • • •
Please contact us for details
Ports: alternative port configurations can be supplied. Materials: suitable combinations of materials can be supplied for various applications such as Oxygen service or semiconductor manufacturing. Certification: variants are available approved for use with Oxygen, for medical Oxygen service or for ATEX service.
HP/UHP 3600 series
Please supply the following information when ordering
Ordering Information • • • • • • • •
Cleanliness level Valve size Actuator required: normally open or normally closed Maximum working pressure Flow medium Port configuration Operating and storage temperature ranges Certification and QA requirements in mm except where shown otherwise
Typical Dimensions
Specification
28
Fixed male VCR
11
• •
Nominal Bore: 5mm Maximum working pressure: 241bar (3500psi) Flow factor (Cv): 0.2 Ports: 1/4” NPT female for HP, 1/4” Cajon VCR compatible male or female, fixed or swivel, or 1/4” stub tube for welding for UHP (alternative ports can be supplied) Weight: 0.35kg Temperature range: -40 to +100°C (extended temperature range versions can be supplied)
55
• • • •
28 59
Fixed female VCR
43
Stub Tubes
45
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
HP/UHP 3600A series Actuated
HP/UHP Diaphragm Stop Valves Typical Dimensions
Specification
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Actuator Port
Ø49 118
Normally closed and normally open actuated variants of the HP/UHP 3600 series are available. The normally closed actuator (LA5) is opened by a low-pressure pneumatic piston and closed by a spring. The normally open actuator (LA4) is closed by a lowpressure pneumatic piston and opened by a spring. The operating force is magnified by an internal hydraulic system. The specifications of the valve are the same as for the manual variant. • Actuator body material: Aluminium alloy • Actuator port: 1/8” NPT • Actuator pressure: 5 bar (75psi) nominal, 7 bar (100 psi) maximum • Weight: approx 0.7kg
in mm except where shown otherwise
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
HP Stop Valves
®
Sealed Spindle
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company Description HP (High Purity) products are for service where the product must be kept free of contamination. The design is kept simple to minimise “dead” areas where contaminants might collect. Elastomers are not used and polymers are carefully selected for suitability. HP products may be used on reactive, corrosive and/or toxic products. Special materials are available for resistance to particularly aggressive chemicals. We offer a range of stop valves in which the metal valve spindle seats directly on a seating face in the valve body. O-rings with back-up rings prevent leakage along the spindle. HP2200 valves have a partially balanced spindle to reduce the load applied by the process pressure. This means that handwheel torque is low even at the maximum operating pressure of the valve and a relatively small actuator can be used. Pneumatically actuated variants are available. Some variants of these valves have passed adiabatic shock tests at the independent test houses BAM and CTE to qualify them for use with Oxygen.
Standard Materials
Alternative materials can be supplied
• Body: Stainless Steel, Monel or Brass • Valve: Stainless Steel or Brass
• O rings: Viton or EPDM • Back up rings: PTFE or Nylon
Options
Ordering Information
• • • • •
Please contact us for details
Ports: alternative port configurations can be supplied. Materials: suitable combinations of materials can be supplied for various applications such as Oxygen service or semiconductor manufacturing. The control knob for HP2000 and 2100 is available in metal or plastic in two styles. A metal handwheel with a locking mechanism is also available. Certification: variants are available approved for use with Oxygen, for medical Oxygen service or for ATEX service. Some variants have passed adiabatic shock (BAM) tests.
• • • • • • • • •
Please supply the following information when ordering
Valve size Actuator required Type of control knob required Locking required Maximum working pressure Flow medium Port configuration Operating and storage temperature ranges Certification and QA requirements
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
HP2000 Stop Valve (4mm)
HP Stop Valves Sealed Spindle
Specification • • •
Control Knob available in Aluminium Alloy or Plastic
Nominal Bore: 4mm Maximum working pressure: 400bar (5800psi) Inlet & outlet Ports: 1/4” NPT female (alternative ports can be supplied) Temperature range: -20 to +150°C (extended temperature range versions can be supplied)
Ø72
12
89
•
in mm except where shown otherwise
Typical Dimensions
Ø57
HP2000 Alternative Handwheels
in mm except where shown otherwise
Typical Dimensions
Optional Locking Aluminium Alloy Handwheel Ø89 Alternative Plastic Handwheel
Ø57
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
12
12
103
104
Ø64
Ø57
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
HP2000A Normally Closed Actuated Valve
®
HP Stop Valves Sealed Spindle
in mm except where shown otherwise
Typical Dimensions
Specification
Ø115
146
The normally closed actuated variant of HP2000 is opened by a low-pressure pneumatic piston and closed by a spring. The specifications of the valve are the same as for the manual variant. • Actuator port: G1/8 • Actuator pressure: 7 bar (100 psi)
60
Actuator Port
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
HP2100 Stop Valve (8mm)
HP Stop Valves Sealed Spindle
Control Knob available in Aluminium Alloy or Plastic
Specification • • •
Nominal Bore: 8mm Maximum working pressure: 400bar (5800psi) Inlet & outlet Ports: 1/2” NPT female (alternative ports can be supplied) Temperature range: -20 to +150°C (extended temperature range versions can be supplied)
Ø97
22
131
•
in mm except where shown otherwise
Typical Dimensions
Ø83
HP2100A Normally Closed Actuated Valve
Typical Dimensions
Specification
in mm except where shown otherwise
Ø148
236
The normally closed actuated variant of HP2100 is opened by a low-pressure pneumatic piston and closed by a spring. The specifications of the valve are the same as for the manual variant. • Actuator port: G1/8 • Actuator pressure: 7 bar (100 psi)
94
Actuator Port
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
HP2200 Stop Valve (12.5mm)
HP Stop Valves Sealed Spindle in mm except where shown otherwise
Typical Dimensions
Specification
20
•
Nominal Bore: 12.5mm Maximum working pressure: 400bar (5800psi) Inlet & outlet Ports: 1/2” NPT female (alternative ports can be supplied) Temperature range: -20 to +150°C (extended temperature range versions can be supplied)
232
• • •
Ø102 177
HP2200A Normally Closed Actuated Valve
in mm except where shown otherwise
Typical Dimensions
Specification
Ø179
The normally closed actuated variant of HP2200 is opened by a low-pressure pneumatic piston and closed by a spring. The specifications of the valve are the same as for the manual variant. • Actuator port: G1/8 • Actuator pressure: 7 bar (100 psi)
133
303
Actuator Port
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
UHP Bellows Stop Valve
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company Description UHP (Ultra High Purity) products are for service where the product must be kept free of contamination. Elastomers and polymers are carefully selected for suitability. Parts are machined to a high surface finish to improve cleanliness. The valve is assembled in a clean room and is Helium leak tested by mass spectrometer. UHP products may be used on reactive, corrosive and/or toxic products. Special materials are available for resistance to particularly aggressive chemicals. CFASV is an actuated stop valve in which a long stroke bellows isolates the operating mechanism from the process fluids. The valve is sealed by a polymer seat. CFASV is intended for vacuum purging of empty gas cylinders. The valve can withstand the rated pressure of a full cylinder on the inlet but will not open unless the inlet pressure is below a safe value. To prevent the shedding of particulate contamination, there are no sliding, rotating or rubbing components in the flow path. A test port is provided to detect and contain leakage across the bellows.
Build Standards • • • •
Built to ultra high purity standards in a dedicated • clean room facility. Ra 10 to 15 micro inch finish on wetted surfaces. • Final assembly and testing is carried out under class 10 conditions. No lubrication is used in the flow path and the seat materials are chosen for minimal gas absorption.
Standard Materials • Body: Stainless Steel • Valve: Stainless Steel
Each valve is tested for leakage using a mass spectrometer. Leak rate is less than 10-7 mbar l/s of Helium, across seat, less than 10-8 mbar l/s of Helium, outboard, less than 10-9 mbar l/s of Helium, inboard.
Alternative materials can be supplied
• Seat: PCTFE • Bellows: Stainless Steel
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
UHP Bellows Stop Valve
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company Options • • •
Ordering Information
Please contact us for details
Ports: alternative port configurations can be supplied. Materials: suitable combinations of materials can be supplied for various applications such as Oxygen service or semiconductor manufacturing. Certification: variants are available approved for use with Oxygen, for medical Oxygen service or for ATEX service.
• • • • • •
Please supply the following information when ordering
Valve size Maximum working pressure Flow medium Port configuration Operating and storage temperature ranges Certification and QA requirements
CFASV •
Specification • • • • •
Nominal Bore: 20mm Maximum inlet pressure – valve closed: 250bar (3625psi) Working inlet pressure range: vacuum to 1.9barg (28psig) – valve will not open at higher pressures Actuator pressure 3bar (44psi) Flow factor (Cv): 9
Typical Dimensions
Inlet Port: 1/2” Cajon VCR compatible female swivel, or stub tube for welding • Outlet Port: stub tube for welding • Actuator port: 1/8” NPT female • Test port: 1/8” NPT female with 1/4” Cajon VCR compatible male adaptor (alternative ports and various sizes of stub tube can be supplied) • Temperature range: -10 to +30°C
in mm except where shown otherwise Ø52
162
175
Actuator Port
Test Port
125
Outlet
62
Inlet 36
Ø74
66 147
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
HP/UHP
®
Non-Return Valve
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company Description HP (High Purity) and UHP (Ultra High Purity) products are for service where the product must be kept free of contamination. The design is kept simple to minimise “dead” areas where contaminants might collect. Elastomers and polymers are carefully selected for suitability. UHP uses a similar design to HP but the parts are machined to a better surface finish to improve cleanliness. The valve is assembled in a clean room and is Helium leak tested by mass spectrometer. HP/UHP products may be used on reactive, corrosive and/or toxic products. Special materials are available for resistance to particularly aggressive chemicals. We offer a range of spring-loaded, non-return or check valves. They are suitable for use with gases or liquids to prevent reverse flow in high-pressure lines. The valves are sealed by an elastomer O ring. The main closing force is provided by the process pressure. The spring ensures that the valve will close at any orientation. The opening (cracking) pressure can be selected by specifying the strength of the closing spring. The internal design of the valve ensures that there is minimal restriction to flow.
Options • • •
Please contact us for details
Ports: alternative port configurations can be supplied. Materials: suitable combinations of materials can be supplied for various applications such as Oxygen service or semiconductor manufacturing. Certification: variants are available approved for use with Oxygen, for medical Oxygen service or for ATEX service.
Build Standards (UHP only) • • • • •
•
Built to ultra high purity standards in a dedicated clean room facility. Ra 10 to 15 micro inch finish on wetted surfaces. Final assembly and testing is carried out under class 10 conditions. Each valve is tested for leakage using a mass spectrometer. Leak rate is less than 10-9 mbar l/s of Helium, inboard, outboard and across seat. No lubrication is used in the flow path and the seat materials are chosen for minimal gas absorption.
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
HP/UHP
®
Non-Return Valve
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company Standard Specification • •
See next page for specification of individual types
Temperature range: -23 to +205°C for Viton seals, -20 to +100°C for Nitrile seals Maximum inlet pressure: 376bar (5450psi)
Ordering Information • • • • • •
•
HP10
Please supply the following information when ordering
Valve size Lift pressure Maximum working pressure Flow medium Port configuration Operating and storage temperature ranges Certification and QA requirements in mm except where shown otherwise
Typical Dimensions
Specification • • • •
Standard Materials • • • •
19 A/F
Ports: 1/4” NPT male or female in any combination Cracking pressures: 0.2 bar (0.3psi), 0.07 bar (1psi), 0.7 bar (10psi), 1.7 bar (25psi), 3.5 bar (50psi), 7 bar (100psi) Flow factor (Cv): 0.45 Weight: 100gm
72
Alternative materials can be supplied
Body: Stainless Steel or Brass Spring: Stainless Steel or Inconel O ring: Viton, Nitrile or Kalrez Guide Ring: PTCFE or Nylon
UHP10
19 A/F
Typical Dimensions
in mm except where shown otherwise
Specification • • • •
Ports: 1/4” Cajon VCR compatible male or female in any combination Cracking pressures: 0.07 bar (1psi), 0.7 bar (10psi), 1.7 bar (25psi) Flow factor (Cv): 0.3 Weight: 70gm
Standard Materials • • • •
17 A/F
56
Alternative materials can be supplied
Body: Stainless Steel or Monel Spring: Stainless Steel or Inconel O ring: Viton, Nitrile, Kalrez or EPR Gasket: PTFE
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
17 A/F
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
UHP Relief Valve
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company Description UHP (Ultra High Purity) products are for service where the product must be kept free of contamination. Elastomers and polymers are carefully selected for suitability. Parts are machined to a high surface finish to improve cleanliness. The valve is assembled in a clean room and is Helium leak tested by mass spectrometer. UHP products may be used on reactive, corrosive and/or toxic products. Special materials are available for resistance to particularly aggressive chemicals. We offer a range of differential relief valves. The valve is operated by an internal piston or diaphragm that is larger than the flow area. The process pressure acts on the difference in these areas (hence “differential”). This means that the spring can be small for high pressures. It also means the valve snaps open to full bore because as soon as the valve starts to open the process pressure acts on the full piston area. Each valve is adjustable within a range of pressures. The range depends on the size of the piston or diaphragm and the strength of the spring.
Options • • •
Ports: alternative port configurations can be supplied. Materials: suitable combinations of materials can be supplied for various applications such as Oxygen service or semiconductor manufacturing. Certification: variants are available approved for use with Oxygen, for ATEX service or as “Safety Accessories” to PED Category 4.
Ordering Information • • • •
Please contact us for details
Build Standards • • •
•
Built to ultra high purity standards in a dedicated clean room facility. Ra 10 to 15 micro inch finish on wetted surfaces. Final assembly and testing is carried out under class 10 conditions. Each valve is tested for leakage using a mass spectrometer.
Please supply the following information when ordering
Relief pressure range Relief set pressure – we can supply valves pre-set to your required pressure Wire locking required (please state set pressure) Flow medium
• •
•
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Port configuration Operating and storage temperature ranges Certification and QA requirements
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
UHP Relief Valve
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
CFRVS High Pressure
in mm except where shown otherwise
Typical Dimensions
Specification
Ø30
•
Pressure ranges:
• • • • •
Nominal bore: 10mm Inlet Port: 1/2” Cajon VCR male Exhaust Port: 1/2” NPT female Weight: 0.5kg Temperature range: -10 to +100°C
Standard Materials
158
36 square Inlet
Alternative materials can be supplied
Body: Stainless Steel Spring Housing: Gunmetal Valve: Stainless Steel Valve Seat: Polyurethane ULON O rings: Viton Back up rings: PTFE
48
• • • • • •
2 to 12 bar (30 to 175 psi), 5 to 30 bar (70 to 430 psi), 17 to 120 bar (250 to 1750 psi), 120 to 320 bar (1750 to 4650 psi)
38 Exhaust
CFLRV Low Pressure
Typical Dimensions
Specification •
Pressure ranges:
• • • • •
Nominal bore: 6mm Inlet Port: 1/4” Cajon VCR male Exhaust Port: 3/8” NPT female Weight: 0.5kg Temperature range: -10 to +100°C
• • •
Ø60
Alternative materials can be supplied
Body: Stainless Steel Spring Housing: Aluminium Alloy Diaphragm: Viton
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
121
0.5 to 2 bar (7 to 30 psi), 2 to 5.5 bar (30 to 80 psi)
Exhaust 32
Standard Materials
in mm except where shown otherwise
Inlet
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
UHP Vacuum Generator
®
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company Description UHP (Ultra High Purity) products are for service where the product must be kept free of contamination. Elastomers and polymers are carefully selected for suitability. Parts are machined to a high surface finish to improve cleanliness. The valve is assembled in a clean room and is Helium leak tested by mass spectrometer. UHP products may be used on reactive, corrosive and/or toxic products. Special materials are available for resistance to particularly aggressive chemicals. The UHP30 vacuum generator uses an ejector mechanism in which a flow of gas creates a vacuum. There are no seals and no moving parts. The body is machined from a single part so there are no leak paths. The vacuum generator is rated to withstand the rated pressure of a full gas cylinder.
Options • • •
Ports: alternative port configurations can be supplied including additional ports for gauges and relief valves. Materials: suitable combinations of materials can be supplied for various applications such as Oxygen service or semiconductor manufacturing. Certification: variants are available approved for use with Oxygen or for ATEX service.
Ordering Information • • • • •
Please contact us for details
Please supply the following information when ordering
Inlet Pressure Flow medium Port configuration Operating and storage temperature ranges Certification and QA requirements
Build Standards • • •
•
Built to ultra high purity standards in a dedicated clean room facility. Ra 10 to 15 micro inch finish on wetted surfaces. Final assembly and testing is carried out under class 10 conditions. Each valve is tested for leakage using a mass spectrometer.
Standard Materials
Alternative materials can be supplied
• Body: Stainless Steel or Monel • Internal jets: Stainless Steel or Monel
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
UHP Vacuum Generator
®
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
UHP30
Typical Dimensions
in mm except where shown otherwise
Specification Maximum pressure: 372bar (5400psi) Recommended inlet pressure: 4bar (60psi) Inlet and vacuum ports: 1/4” Cajon VCR compatible male Outlet port: 1/2” Cajon VCR compatible male Temperature range: -40 to +300°C Weight: 135gm
• • •
51 24 Vacuum
Outlet
33
• • •
Inlet
Typical Performance Characteristics 12
30
Vacuum inch Hg
25 20 15 10 5 0
10
20
30
40
50
60
70
24
Flow l/min Outlet restriction must be less than the equivalent of a 6.3mm ID tube of 300mm length
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
Excellence in Pressure & Flow Control
Clean Gas Panels
A CIRCOR International, Inc. Company Description Clean gas panels consist of one or more of our High Purity regulators mounted on a panel with gauges and stop valves. The configurations shown here use the HP1550 regulator and offer flow rates of about 150 l/min at 10bar. Similar configurations can be supplied using our HP1100 to give higher flow or our two stage HP1700 to give better accuracy. For more details of the flow characteristics please see our Clean gas regulators data sheet. We can supply systems with appropriately rated pressure gauges and relief valves to operate at different inlet and outlet pressures from those shown below. Standard Configurations The configurations shown in detail on the following pages are available as standard items: • Type 2 Regulator Station • Type 5 Regulator Station • ACU1550 Auto Changeover Unit Other configurations can be designed as required. Please contact us for details.
Standard Specification
Standard Materials
• •
•
Nominal Bore: 6mm Temperature range: -20 to +70°C
Options • • •
Please contact us for details
Ports: alternative port configurations can be supplied Materials: suitable combinations of materials can be supplied for various applications. Bottle connections: we can supply metal tube or flexible hose connections terminated with any industry standard connector
Valve bodies and panel: Stainless Steel
Ordering Information • • • • • • •
Alternative materials can be supplied
Please supply the following information when ordering
Panel Configuration Inlet Pressure Outlet pressure range Flow medium Port configuration Operating and storage temperature ranges Certification and QA requirements
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
Clean Gas Panels
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
Type 2 Regulator Station Specification Single stage regulator station with stop valve to vent the inlet, stop valve to isolate the outlet, pressure gauges on inlet and outlet and a relief valve to prevent over pressure. • Inlet pressure: 200bar (2900psi). Alternative inlet pressures up to 376bar can be supplied. • Outlet pressure: 0 to 10bar (0 to 145psi) Alternative outlet pressure ranges can be supplied - see the data sheet for HP1550 • Weight: approx. 3kg
170
Typical Dimensions
Typical P & ID Inlet Pressure Gauge
Outlet Pressure Gauge
Vent/ Purge
Outlet Controller
Outlet Stop Valve Relief Valve
Vent Stop Valve Inlet
in mm except where shown otherwise
Outlet Inlet
Vent/ Purge
260
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
200
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
Excellence in Pressure & Flow Control
Clean Gas Panels
A CIRCOR International, Inc. Company
Type 5 Regulator Station Specification Single stage regulator station with stop valve to isolate the inlet outlet and a pressure gauge on the outlet. • Inlet pressure: 376bar (5450psi). • Outlet pressure: 0 to 5bar (0 to 73psi) Alternative outlet pressure ranges can be supplied - see the data sheet for HP1550 • Weight: approx. 2kg
Typical Dimensions
Typical P & ID Outlet Pressure Gauge Inlet Outlet Controller
Inlet Stop Valve
Outlet
in mm except where shown otherwise
200
Inlet
Outlet Outlet
130
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
140
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10
HALE HAMILTON
®
Clean Gas Panels
Excellence in Pressure & Flow Control
A CIRCOR International, Inc. Company
ACU1550 Auto Changeover Unit Specification Two stage regulator system in which the first stage automatically accepts gas supply from the cylinder storage bank with the highest pressure. The bank priority is controlled by a lever connected to both first stage regulators. Pressure gauges and stop valves are fitted to control and monitor the flow. • Inlet pressure: 200bar (2900psi). Alternative inlet pressures up to 376bar can be supplied. • Outlet pressure: 0 to 5bar (0 to 73psi) Alternative outlet pressure ranges can be supplied - see the data sheet for HP1550 • Weight: approx. 10kg Typical Dimensions
Typical P & ID Outlet Relief Valve
Outlet Pressure Gauge
Outlet Controller
Inlet Controller Inlet Pressure Gauge
Inlet Controller Inlet Pressure Gauge
Non Return Valve Inlet Stop Valve From Bank B
From Bank A
in mm except where shown otherwise
190
320
252
Outlet
From Bank A
In addition to our standard product range, we have an extensive range of special designs and offer a custom build service. Contact our Sales office if you don’t see what you want in our catalogue. The information contained within this catalogue is for reference purposes only and is subject to change. When selecting a product, the total system design must be considered to ensure safe, trouble free performance. Component function, material compatibility, adequate ratings, proper installation, operation and maintenance are the responsibility of the system designer and user.
From Bank B
Hale Hamilton (Valves) Ltd Cowley Road, Uxbridge, UB8 2AF, UK Tel: 01895 236 525 www.halehamilton.com Sep 10