IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
ACS88FP Issue 0110
ASHCOMBE SUMMER HOUSE Thank you for choosing this garden product manufactured by the UK's largest manufacturer of timber garden products. In order to gain the most benefit from it, please note the following: - If there are any technical queries with the product, please contact our customer help line on 0844 248 9853 between the hours of 8.30 am and 5.00 pm Monday to Friday. - Please ensure that you thoroughly check all component parts for quantity and quality before you commence building the product. If there are any missing parts, please contact the help line as shown immediately. The manufacturer cannot be held liable for damaged items once any part of the product has been fitted or altered in any way (e.g. Painted) - Timber is a natural material. It will shrink and swell as a result of varying moisture content. - Please keep all plastic bags and small parts away from children in order to reduce the risk of suffocation. - This product must be built on a solid level base. - The roof of this building is not a load bearing structure.
JE
Recommended Tools (not supplied)
POZI DRIVE SCREWDRIVER
DRILL
SHARP KNIFE TO CUT ROOF FELT
Important : Assembly of this product requires two people.
MUST PRE DRILL
TAPE MEASURE
SPIRIT LEVEL
HAMMER
Component List
SHLHA (LEFT HAND APEX) X2
SHRHA (RIGHT HAND APEX) X2
SHTRUSS (TRUSS) X 2
SHPP4 (PLAIN PANEL) X 2
SHWP2 (WINDOW PANEL) X 3
SHPP2 (PLAIN PANEL) X3
SHDP6 (DOOR PANEL) X 1
SHPP6 (LARGE PLAIN PANEL) X 1
SH88FL (FLOOR) X 2
88mm
487mm
1219mm
1300mm
Felt
1219889PLY (1219 x 88 x 9mm PLYWOOD) X2 1267mm
1219mm
HM121121100A1 (121 x 12 x 1100mm BOARD) X2
553mm
780mm
Felt x 3 (85060)
900mm
400mm
SUMHDRV2LHMDTR (MORTICED DOOR) X 1 SUMHDRV2RHDTR ( DOOR) X 1
Fixing Pack x 1 (ACS88FP)
SANW780400 (DOOR GLAZE) X4
SANW1345550 (WINDOW GLAZE) X3
12195539PLY (1219 x 553 x 9mm PLYWOOD) X2
13009009PLY (1300 x 900 x 9mm PLYWOOD) X8
Forest Garden Ltd, Units 291 & 296 Hartlebury Trading Estate, Hartlebury, Worcestershire, DY10 4JB
HM121122095A1 (121 x 12 x 2095mm BOARD) X2
STRIPS 14 x
= 56121945PARDTR
56x12x1945mm
2x
= 56120590PARDTR
56x12x590mm
4x
= 56121595PARA1DTR
3x
= 69120554PARDTR
4x
= 85121312PARDTR
85x12x1312mm
4x
= 85121945PARDTR
85x12x1945mm
4x
= 85121802PARA1DTR
1x
= 45121116DTR
1x
= 56121775PARDTR
1
56x12x1595mm ANGLED 69x12x554mm
2 x (floor sections)
85x12x1802mm ANGLED BARGE BOARD
45x12x1116mm 56x12x1775mm
2 BEADING 2x
= 15121116DTR
15x12x1116mm
= 15121749DTR
15x12x1749mm
2x
8x
= 15150405SA2DTR
15x15x405mm
12 x
= 15150554SA2DTR
15x15x554mm
8x
= 15150784SA2DTR
15x15x784mm
12 x
= 15151349SA2DTR
15x15x1349mm
3
Place the sections on to the floor as illustrated. Fix them to each other using 3 x 50mm screws for each panel.
BATTEN 8x
= 45280850PAR 45x28x850mm
8x
= 45281151PAR
45x28x1151mm
4x
= 45281300PAR
45x28x1300mm
Fix the doors into the door panel using 2 x hinge for each door. Secure using 30mm screws. 24 x 30mm screws 4 x hinge
30 x 50mm screws
4 ACS88FP Fixing Pack 8mm Tacks Qty 250
50mm screw Qty 70
Z’Plate Qty 16 Handle set Qty 1
Hinge Qty 4
30mm screw Qty 24
25mm screw Qty 148
Lock Qty1
25mm glazing pins Qty 156
30mm nail Qty 98
Cabin Hook Qty 2 Barrel Bolt Qty 2
Once all the panels are secured to each other and positioned squarely on the floor, secure them to the floor using 16 x 50mm screws.
Fix the left and right apex’s to each other using 2x50mm screws. Repeat the step on the truss sections. 6 x50mm screws
5
56121945PARDTR Corner Place the Strips on the corners of the building as shown. Make sure each strip is flush and secure into position using 3 x 30mm nails for each .
Board HM121122095A1
85121945PARDTR
36x 30mm nails
1152 mm
8
Board HM121121100A1
14 x Cover Strips 56121945PARDTR
6
4 x Corner Strips 85121945PARDTR
Fix the HM angled boards to the assembled truss as shown. Make sure these are flush and secure in place using 2 x 30mm nails for each batten they cross. 28x30mm nails
Place the Cover Strips over the joins of the panels. Make sure each strip is flush and secure into position using 3 x 30mm nails.
Place the completed gables onto the end of the building making sure the overhang is correct. Secure to the top of the panels using 4 x 50mm screws. Position the completed truss as illustrated, 1152mm away from the gables, on to the building. Fix in place by screwing up through the building frame work using 2 x 50mm screws for each end. 12x50mm screws
18x 30mm nails
m 88vemrhang O
7 BATTEN 45281151PAR
Using the Z’ plates provided, secure one to each end of the battens. Position these as shown and fix to the gable and truss using the reverse of the Z’ plate. 32x25mm screws 16 x Z’ plates
Place the strips over the joins of the gables to the side panels. Make sure each strip is flush and secure into position using 3 x 30mm nails. 2 x 30mm nails for the smaller strip 16 x 30mm nails
9 STRIP 56120590PARDTR
STRIP 56121595PARA1DTR
Z’ plate
12 14 PLY 13009009PLY
Place each of the large sheets of Ply board on to the building as shown. Screw each board into position, making sure that the screws locate in to the battens underneath.
10 Fix the 1116mm strip at the bottom of the door way so it is flush on all sides. Fix using 3 x 25mm screws.
The boards must overhang to the dimension shown in the boxes below.
45121116DTR
3 x 25mm screws
40x25mm screws
68mm 56mm Side view
11
Front view
13
Fix each batten to the under side of the Ply board by screwing through the board into the battens using 2 x 25mm screws for each. Make sure the battens are flush on all sides.
PLY 13009009PLY
24x25mm screws 45280850PAR
Place the two 553mm pieces of Ply board up against the underside of the Trusses and Gables. Fix each board into place by screwing at both ends using a single 25mm screw. Repeat the step for the back of the building with the 88mm pieces of Ply board. 8 x 25mm screws
45281300PAR
BACK
16
14
Fix 554mm boards at the bottom of the window. Make sure that they are flush and in line with the cover strips. Secure each in place using 2 x 25mm screws 6 x 25mm screws
69120554PARDTR
17
250 x 8mm felt tacks
Place the smaller glazing in to the doors . Place the beading against the glaze as shown making sure it is flush and secure each piece using the glazing pins provided. Use 24 x glazing pins for each door.
GLAZE 780 x 400
Cut the rolls of felt into equal lengths and place them as shown making sure each layer overlaps the next by at least 50mm. Fix the felt in place using the felt tacks provided, spaced out 150mm apart.
Protect glazing when fixing the beading 48 x 25mm glazing pins
BEADING FOR THE DOORS
15150405SA2DTR X 8 15150784SA2DTR X 8
85121312PARDTR
18 85121802PARA1DTR
85121312PARDTR
Fix the barge boards in place using 4 x 25mm screws for each making sure that you screw into the battens and not the Ply board. Trim off any excess felt that sticks out. 32 x 25mm screws
Fix the shaped beading inside the window panel as shown. Make sure there is a gap away from the edge of the sill. Fix the beading in place using 25mm glazing pins. Place the glazing inside this and repeat the step with the remaining beading from the inside, sandwiching the glazing in between. Protect glazing when fixing the beading 84 x 25mm glazing pins
GLAZE 1345 X 550
17 15
BEADING FOR THE WINDOWS
15150554SA2DTR X 12 15151349SA2DTR X 12
19
21
Position the Barrel Bolt at the top and bottom of the door, so that the bar locates over the beading correctly. Fix in place using the screws provided.
Fix the door beading around the entrance of the door making sure that it is all flush with the inside of the framework. 24 x 25mm glazing pins
20a
20
Make sure the position of the catch plate lines up correctly with the lock on the opposite door. Place one screw in the top and pencil around the gap. Take the plate off and chisel out the recess. Fix the plate into position using the screws provided.
20
Place the lock into the recess on the door. Insert the spindle and make sure it lines up correctly before fixing the lock in place using the screws provided.
22
Place the handles against the door, again making sure that it is all lined up, and secure using the screws provided.
Place the 56x12x1775mm strip over the front of the doors so that it covers the join between them. Make sure it is flush at the top and bottom and secure to the right hand door using 3x25mm screws. 3x25mm Screws
23 Catch can be changed by pulling it and twisting
Open the door to the desired position when secured. Mark the positions and fix the Hook and Eye in place using the screws provided.