IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY Issue 0110
LARKSWOOD SUMMER HOUSE Thank you for choosing this garden product manufactured by the UK's largest manufacturer of timber garden products. In order to gain the most benefit from it, please note the following: - If there are any technical queries with the product, please contact our customer help line on 0844 248 9853 between the hours of 8.30 am and 5.00 pm Monday to Friday. - Please ensure that you thoroughly check all component parts for quantity and quality before you commence building the product. If there are any missing parts, please contact the help line as shown immediately. The manufacturer cannot be held liable for damaged items once any part of the product has been fitted or altered in any way (e.g. Painted) - Timber is a natural material. It will shrink and swell as a result of varying moisture content. - Please keep all plastic bags and small parts away from children in order to reduce the risk of suffocation. - This product must be built on a solid level base. - This building is not a load bearing structure.
JE
Recommended Tools (not supplied)
DRILL
POZI DRIVE SCREWDRIVER
SHARP KNIFE TO CUT ROOF FELT
Important : Assembly of this product requires two people.
MUST PRE DRILL
TAPE MEASURE
HAMMER
SPIRIT LEVEL
Component List
SHLHA (LEFT HAND APEX) X2
SHRHA (RIGHT HAND APEX) X2
SHTRUSS (TRUSS) X 4
SHPP4 (PLAIN PANEL) X 2
SHWP2 (WINDOW PANEL) X 6
SHDP6 (DOOR PANEL) X 1
SHPP6 (LARGE PLAIN PANEL) X 1
550mm
SHPP2 (PLAIN PANEL) X2
SH108FL (FLOOR) X 2 70701906PARDTR (70 x 70 x 1906mm POST) X2 1072mm
1072mm
SUMHDRV2LHMDTR (MORTICED DOOR) X 1 SUMHDRV2RHDTR ( DOOR) X 1
Fixing Pack x 1 (LKSFP)
1345mm
88mm
SANW780400 (DOOR GLAZE) X4
SANW1345550 (WINDOW GLAZE) X6
988mm
988889PLY (988 x 88 x 9mm PLYWOOD) X2
553mm 900mm
1072889PLY (1072 x 88 x 9mm PLYWOOD) X1
780mm
Shingles x 7 (ERSGPKGRN)
988mm
1072mm 553mm
88mm
400mm
10725539PLY (1072 x 553 x 9mm PLYWOOD) X1
HM121121100A1 (121 x 12 x 1100mm BOARD) X4
10729009PLY (1072 x 900 x 9mm PLYWOOD) X 12
9885539PLY (988 x 553 x 9mm PLYWOOD) X 2
HM121122095A1 (121 x 12 x 2095mm BOARD) X4
Forest Garden Ltd, Units 291 & 296 Hartlebury Trading Estate, Hartlebury, Worcestershire, DY10 4JB
STRIPS 16 x
= 56121945PARDTR
56x12x1945mm
2x
= 56120590PARDTR
56x12x590mm
4x
= 56121595PARA1DTR
6x
= 69120554PARDTR
4x
= 85121620PARDTR
= 85121945PARDTR
85x12x1945mm
6x
= 70150900PARDTR
70x15x900mm
4x
= 85121802PARA1DTR = 45121116DTR
1x
85x12x1802mm ANGLED BARGE BOARD
45x12x1116mm
= 56121775PARDTR
BEADING 2x 2x 8x 24 x 8x 24 x
= 15150405SA2DTR 15x15x405mm = 15150554SA2DTR 15x15x554mm = 15150784SA2DTR 15x15x784mm = 15151349SA2DTR 15x15x1349mm
BOARD 5x
= PATDB1PTR
5x
= 15121116DTR
56x12x1775mm
15x15x1116mm = 15121749DTR
2 15x15x1749mm
DECK BOARD PROFILE
DECK BOARD
3
= 120280704PTR 120x28x704mm DECK BOARD
5x
= 120280620PTR 120x28x620mm DECK BOARD
4x
= 70280535PARA1DTR 70x28x535mm ANGLED
2x
= 70280535NPARDTR 120x28x820mm NOTCHED
Place the sections on to the floor as illustrated. Fix them to each other using 3 x 50mm screws for each panel.
BATTEN 8x
2 x (floor sections)
85x12x1620mm BARGE BOARD
4x
1x
1
56x12x2151mm ANGLED 69x12x554mm
= 45280850PAR 45x28x850mm
8x
= 45280920PAR 45x28x920mm
4x
= 45281027PAR
LKSFP Fixing Pack
13mm Tacks Qty 300
24 x 30mm screws 4 x Hurling Hinge
36 x 50mm screws
45x28x1027mm
= 45281072PAR
6x
Fix the doors into the door panel using 2 x hinge for each door. Secure using 30mm screws.
45x28x1072mm
Z’Plate Qty 24
Handle set Qty 1
4 Lock Qty1
70mm screw Qty 4
Corner Brace Qty 6
Hurlinge Hinge Qty 4
Cabin Hook Qty 2 50mm screw Qty 146 30mm screw Qty 63 25mm screw Qty 195
25mm glazing pins Qty 240 30mm nail Qty 132
Casement stay Qty 2 Barrel Bolt Qty 2
Once all the panels are secured to each other and positioned squarely on the floor, secure them to the floor using 18 x 50mm screws.
Fix the left and right gable to each other using 2x50mm screws. Repeat the step on the Trusses 8 x50mm screws
5
56121945PARDTR Corner Place the Strips on the corners of the building as shown. Make sure each strip is flush and secure into position using 3 x 30mm nails for each .
Board HM121122095A1
921 m
85121945PARDTR
m
36x 30mm nails
8
Board HM121121100A1
You will need to trim the Strips for the front of the building to allow for the positioning of the deck
6 Fix the HM angled boards to the assembled Trusses as shown. Make sure these are flush and secure in place using 2 x 30mm nails for each batten they cross. 56x30mm nails
16 x Cover Strips 56121945PARDTR 4 x Corner Strips 85121945PARDTR
A
Place the Cover Strips over the joins of the panels. Make sure each strip is flush and secure into position using 3 x 30mm nails.
B
Place the completed gables on to the end of the building making sure the overhang is correct. Secure to the top of the panels using 4 x 50mm screws. Position the trusses as illustrated, 921mm from the gables, on to the building. Fix in place by screwing up through the building frame work using 2 x 50mm screws for each end. 16x50mm screws
24x 30mm nails
m 88vemrhang O
9
7 Using the Z’ plates provided, secure one to each end of the battens. Position these as shown and fix to the Gable and Truss using the reverse of the Z’ plate. 48x25mm screws 24 x Z’ plates
BATTEN 45280920PAR
BATTEN 45281072PAR
BATTEN 45280920PAR Z’ plate
Place the strips over the joins of the trusses to the side panels. Make sure each strip is flush and secure into position using 3 x 30mm nails. 2 x 30mm nails for the small strip 16 x 30mm nails
STRIP 56120590PARDTR
STRIP 56121595PARA1DTR
10a
Position the 5x600mm deck boards as shown. Place the remaining deck boards on top of these to the pattern below and secure at each end using 2 x 50mm screws.
Using the Rail as a guide, position the post on the deck so that it is underneath the Gable. Use 2x70mm screws to screw down through the gable into the post. Place a corner brace against the inside of the post at the base and secure it to the post and the deck using 4 x 30mm screws.
12
Make sure each row has a 5mm gap between them. 60 x 50mm screws
10
730mm
528mm
2xCorner Brace 8x30mm screw 4x70mm screw
5mm gap RAIL 70280535NPARDTR
Fix the 1116mm strip at the bottom of the door way so it is flush on all sides and does not create a trip hazard. Fix using 3 x 30mm screws.
POST 70701906PARDTR Deck Pattern
3 x 30mm screws
13 11 PLY 9885539PLY
PLY 10725539PLY
Use a 900mm board as a guide and fix the 535mm angled boards at the top and bottom. Secure using a corner brace, fixed to the angled boards and the building using 4 x 30mm screws for each. Secure the other end of the angled board to the post using a 1 x 50mm screw. 4xCorner Brace 16x30mm screw 4x50mm screw
PLY 9885539PLY
A
13a
13b
Fix the 900mm boards to the angle boards, spaced out evenly, using 1x30mm screw each end. 12x30mm screw
Place the three 553mm pieces of Plyboard up against the underside of the Trusses and Gables. Fix each board into place by screwing at both ends using a single 25mm screw. Repeat the step for the back of the building with the 88mm pieces of Plyboard. 12 x 25mm screws
Place the rail on top of the angled board and fix in place using 2x50mm screws. 4x50mm screw
14
16
PLY 10729009PLY
Place each of the large sheets of Ply Board on to the building as shown. Screw each board into position, making sure that the screws locate in to the battens underneath.
Place the first layer of shingles in reverse and fold it over the edge. Fix these in place using the tacks, spaced approximately 150mm apart. Place the remaining layers so that they overlap as shown.
The boards must overhang to the dimension shown in the boxes below. 60x25mm screws
16a
68mm 56mm Side view
Front view
To cover the apex you will need to cut some of the shingles into there individual squares. Place these across the apex so they overlap each other 50mm. Secure using the tacks provided.
Fix each batten to the under side of the Ply Board by screwing through the board into the battens using 2 x 25mm screws for each. Make sure the battens are flush on all sides.
15 45280850PAR
28x25mm screws
17 85121620PARDTR
452801072PAR
85121802PARA1DTR 85121620PARDTR
Fix the barge boards in place using 4 x 25mm screws for each making sure that you screw into the battens and not the Plyboard. 32 x 25mm screws
18
Fix 554mm boards at the bottom of the window. Make sure that they are flush and in line with the cover strips. Secure each in place using 2 x 25mm screws 12 x 25mm screws
69120554PARDTR
GLAZE 1345 X 550
20
Fix the shaped beading inside the window panel as shown. Make sure there is a gap away from the edge of the sill. Fix the beading in place using 25mm glazing pins. Place the glazing inside this and repeat the step with the remaining beading from the inside, sandwiching the glazing in between. Protect glazing when fixing the beading 168 x 25mm Glazing Pins
BEADING FOR THE WINDOWS
15150554SA2DTR X 24 15151349SA2DTR X 24
19
GLAZE 780 x 400
Place the smaller glazing in to the doors . Place the beading against the glaze as shown making sure it is flush and secure each piece using the glazing pins provided. Use 24 x Glazing pins for each door. Protect glazing when fixing the beading 48 x 25mm Glazing Pins
Position the Barrel Bolt at the top and bottom of the door, so that the bar locates over the beading correctly. Fix in place using the screws provided.
21
22 BEADING FOR THE DOORS
15150405SA2DTR X 8 15150784SA2DTR X 8
Fix the square door beading around the entrance of the door making sure that it is all flush with the inside of the framework. 24 x 25mm Glazing pins
23
25
Place the lock into the recess on the door. Insert the spindle and make sure it is lined up correctly before fixing the lock in place using the screws provided. Place the handles against the door, again making sure that it is all lined up and secure using the screws provided.
56121775PARDTR
Place the 56x12x1775mm strip over the front of the doors so that it covers the join between them. Make sure it is flush at the top and bottom and secure to the left hand door using 3x25mm screws.
Catch can be changed by pulling it in and twisting
3x25mm Screws
24
26
Open the door to the desired position when secured. Mark the positions and fix the Hook and Eye in place using the screws provided. Make sure the position of the catch plate lines up correctly with the lock on the opposite door. Place one screw in the top and pencil round the gap. Take the plate off and chisel out the recess. Fix the plate into position using the screws provided.