5. Bargeboards and finials Position bargeboards at the front so that the top edge is flush with the roof line and the two boards meet evenly in the middle secure each board using 4 x 40mm and 1 x 70mm screws. Screw through the pre-drilled holes, using the diagram below for the positions of the 70mm screws. Attach a finial centrally over the join between the bargeboards use 2 x 40mm screws. In the same way fit two bargeboards and a finial to the back of the arbour.
English SS307
Britannia Arbour Assembly Instructions Before assembly
40mm
• We recommend that time is taken to
read the instructions before starting assembly, then follow the easy step by step guide.The instruction sheet is only a guide to the assembly. Certain items may not be shown to scale. • Check all components prior to assembly • This product should be assembled by no less than two people. • Never attempt to erect the assembly in high winds.
70mm
40mm
40mm
70mm
40mm
x2 70mm
Recommended tools for assembly
• Power drill/screwdriver • Cross head screwdriver bit
40mm
Safety information
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY When the side tables are put in the raised position, ensure they are locked in place by turning the turn buttons. When used as a Barbecue Station, the barbecue should not be left unattended. Periodically check all fastenings for tightness For domestic use only
If in doubt of any aspect regarding the assembly, use or safety of your arbour please contact us :
No. 1 2 3 4 5 6 7 8 9 10 11
Components Left upright Right upright Seat Seat back Back panel Top rail Roof panel Gusset Roof coverstrip Bargeboard Finial
Qty. 1 1 1 1 1 1 2 2 1 4 2
No. 12 13 14 15
Fixing kit 90mm screws 70mm screws 50mm screws 40mm screws
Qty. 2 12 5 40
8 9
6 10
11
7 5
4
1
Help Line (Normal Office Hours) 01829 261 121 ROWLINSON GARDEN PRODUCTS LIMITED Green Lane Wardle Nr. Nantwich Cheshire CW5 6BN
We constantly improve the quality of our products, occasionally the components may differ from the components shown and are only correct at time of printing. We reserve the right to change the specification of our products without prior notice.
2013 © Rowlinson Garden Products Ltd
3
2
1. Seat to upright
3. Back panel
Position the seat between the two upright so it rests on the seat support rail. Have the seat as far forward as possible so that the rebates in the front corners of the seat fit around the front legs of the upright. Secure the seat in place using 2 x 70mm screws per upright. Screw up through the pre-drilled holes in the seat support rail into the frame of the seat.
Position the back panel between the upright behind the seat. Ensure the panel is level with the top of the two upright and secure using 4 x 50mm screws. Screw through the pre-drilled holes in the panel into the leg of the upright. Using 1 x 50mm screw, screw through the pre-drilled hole in the back panel into the middle support of the seat back. Place the top rail on top of the back panel as shown below. Ensure the top rail is sitting centrally and secure down using 4 x 35mm screws through the pre-drilled holes.
35mm
50mm
50mm
Seat support rail
600mm
4. Roof assembly 70mm 70mm
Seat front corner rebates
2. Seat back
Join the two halves of the roof together using the two gussets. Position the gussets on the inside of the roof bearers. Secure each gusset in place using 6 x 40mm screws. Place the roof coverstrip on top of the ridge and screw down at each end using 2 x 40mm screws. Screw through the pre-drilled holes in the coverstrip into the roof panels. Lift the roof onto the upright. Ensure the rebates in the roof rafters rest on the upright and that the roof sits flush with upright at the front and rear. Secure each front corner in place using 1 x 90mm screws. Screw up through the pre-drilled holes in the upright into roof panels.
Place the seat back so that the bottom rail of the seat back is up against the back rail of the seat. From the back screw through the pre-drilled holes in rail of the seat back into the seat using 4 x 70mm screws
roof bearer
40mm
View of gusset fitted inside the roof.
40mm 40mm
Bottom rail of seat back. Back rail of seat.
90mm
70mm