Service Manual Clarion Pu-2610a-a -b Car Stereo Player by www.heydownloads.com

Clarion Co., Ltd.

Published by Service Dept. 298-6157-00 Jan.2005

50 Kamitoda, Toda-shi, Saitama 335-8511 Japan Service Dept.: 5-66 Azuma , Kitamoto-shi, Saitama 364-0007 Japan Tel: +81-48-541-2335 / 2432 FAX: +81-48-541-2703

Printed in Japan

Service Manual LAND ROVER Genuine 6 Disc CD Changer Model

PU-2610A-A (Genuine No. XQE500201) (Serial No.0000001 - 0017803)

Model

PU-2610A-B (Genuine No. XQE500202) (Serial No.0017804 or later)

SPECIFICATIONS

CAUTIONS

Optical power output: BUS system: Power supply voltage: Ground: Current consumption: Dimensions(mm): Weight:

Use of controls,adjustment or performance of procedures other than those specified herein,may result in hazardous radiation exposure. The COMPACT DISC player should not be adjusted or repaired by anyone except properly qualified service personnel.

-10 to -1.5dBm MOST BUS 13.5V DC Negative 5A 225(W) x 63(H) x 197.5(D) 1.8kg

This appliance contains a laser system and is classified as a "CLASS 1 LASER PRODUCT". In case of any trouble with this player, please contact your nearest"AUTHORIZED service station". To prevent direct exposure to the laser beam, do not to open the enclosure.

COMPONENTS PU-2610A-A / A-B 1. 2.

Main unit CD magazine

----------CAA-397-700

1 1

NOTES *

THIS PRODUCTION COMPLIES WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE.

The differences between "PU-2610A-A" and "PU-2610AB" are a SETPLATE and a FLASH ROM(IC102) of Main PWB(B2) section. The same parts are used except it.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMUFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCR THAT MAY CAUSE UNDESIRED OPERATION. PART No. 285-1939-00

* *

We cannot supply PWB with component parts in principle. When a circuit on PWB has failure , please repair it by component parts base. Parts which are not mentioned in service manual are not supplied. Specifications and design are subject to change without notice for further improvement. This unit is used special adjustment jig for measuring.

-1-

L AND PART HW : 10

ROV E R

NO. 12V

SW :

GR OU N D

SERIAL

NO.

Manufacturers part no.

e 1 3 0 219 74 EMC TYPE

542420

PU- 2 6 1 0 A CL

Sc r a p p e d MANUFACTURED DATE

S ER I A L

i f

NO.

d r o p p e d CLASS 1 LASER PRODUCT

ASSEMBLED IN CHAINA

PU-2610A

In case that main unit is transported for repair, the lock pin (335-0594-21 x 3pcs) must be set to fix the mechanism assy. (Please insert and turn the lock pins.) Bottom view

Lock pin 355-0594-21

The locking state with the lock pins.

To engineers in charge of repair or inspection of our products. Before repair or inspection, make sure to follow the instructions so that customers and Engineers in charge of repair or inspection can avoid suffering any risk or injury. 1. Use specified parts. The system uses parts with special safety features against fire and voltage. Use only parts with equivalent characteristics when replacing them. The use of unspecified parts shall be regarded as remodeling for which we shall not be liable. The onus of product liability (PL) shall not be our responsibility in cases where an accident or failure is as a result of unspecified parts being used. 2. Place the parts and wiring back in their original positions after replacement or re-wiring. For proper circuit construction, use of insulation tubes, bonding, gaps to PWB, etc, is involved. The wiring connection and routing to the PWB are specially planned using clamps to keep away from heated and high voltage parts. Ensure that they are placed back in their original positions after repair or inspection. If extended damage is caused due to negligence during repair, the legal responsibility shall be with the repairing company. 3. Check for safety after repair. Check that the screws, parts and wires are put back securely in their original position after repair. Ensure for safety reasons there is no possibility of secondary ploblems around the repaired spots. If extended damage is caused due to negligence of repair, the legal responsibility shall be with the repairing company. 4. Caution in removal and making wiring connection to the parts for the automobile. Disconnect the battery terminal after turning the ignition key off. If wrong wiring connections are made with the battery connected, a short circuit and/or fire may occur. If extensive damage is caused due to negligence of repair, the legal responsibility shall be with the repairing company. PU-2610A

5. Cautions regarding chips. Do not reuse removed chips even when no abnormality is observed in their appearance. Always replace them with new ones. (The chip parts include resistors, capacitors, diodes, transistors, etc). The negative pole of tantalum capacitors is highly susceptible to heat, so use special care when replacing them and check the operation afterwards. 6. Cautions in handling flexible PWB Before working with a soldering iron, make sure that the iron tip temperature is around 270 . Take care not to apply the iron tip repeatedly(more than three times)to the same patterns. Also take care not to apply the tip with force. 7. Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit. 8. Cautions in checking that the optical pickup lights up. The laser is focused on the disc reflection surface through the lens of the optical pickup. When checking that the laser optical diode lights up, keep your eyes more than 30cms away from the lens. Prolonged viewing of the laser within 30cms may damage your eyesight. 9. Cautions in handling the optical pickup The laser diode of the optical pickup can be damaged by electrostatic charge caused by your clothes and body. Make sure to avoid electrostatic charges on your clothes or body, or discharge static electricity before handling the optical pickup. 9-1. Laser diode The laser diode terminals are shorted for transportation in order to prevent electrostatic damage. After replacement, open the shorted circuit. When removing the pickup from the mechanism, short the terminals by soldering them to prevent this damage. 9-2. Actuator The actuator has a powerful magnetic circuit. If a magnetic material is put close to it. Its characteristics will change. Ensure that no foreign substances enter through the ventilation slots in the cover. 9-3. Cleaning the lens Dust on the optical lens affects performance. To clean the lens, apply a small amount of isopropyl alcohol to lens paper and wipe the lens gently.

-2-

-3-

UP/DOWN MOTOR

LED

12/8-DISC SENSOR

D 3.3V MUTE

RESET WAKE MAGAZINE SW S2

SRQ SYS 9V

POSITION SW HLZ00110676 S1

IC204 MICOM M30624FGAGP

V-BUS

IC102 FLASH ROM MBM29DL800B

DISC NO. TR GP1394 IC3

VDD 5V

PON1 MOST ON

SYS 5V

GAIN WAKE UP INT PON1 MOST ON RESET 7V_DET INT THERMISTER AD +B_DET INT +B_DET AD

IC5 B/U DETECT CIRCUIT

IC203 SYS5V BA05ST

IC103 DECODE LV139APWR

IC105 FLIP FLOP LV74APWR

IC104 SDRAM K4S641632E-TCL60

IC205 TEMP SENSOR LM20BIM7

IC101 DECODE LV139APWR

RMCK-SW MOST-STATUS MOST-RST MOST-CS MOST-ERROR MOST-TXD MOST-CLOCK MOST-RXD INT INT AINT INT

D 3.3V

CLK input 12.288MHz

SPDIF Fs=48kHz

SN74HCT08PW IC207

MSI SERIAL

EJECT SW SKHLLD S3

16MHz

IC201 EEPROM BR93L56RFVM

IC4 CD3.3V REG BA033SFP

UDCCW UDCW LDCW LDCCW DR MUTE

CS MSO SERIAL SCK SERIAL

HOLDER-IN SW

LOAD-END SW

/PON2 PON2

RESET WAKE TC74LCX07FT IC206

CCS CMSI SERIAL CSCK SERIAL

MOTOR DRIVER

IC106 DSP TMS320DA140

CSRQ

LOADING MOTOR

BD7961FM

SFSY(INT) SBSY(INT) IPF(INT) MBOV

SIGNAL

BUS0 BUS1 BUS2 BUS3 BUCK /CCE /RST

BUS

LRCK BCLKI DATA

AUDIO DATA(3)

CMSO SERIAL

LOADING FPC

IC2

SERVO DRIVER

IC107 DSP 1.6V

IC1 RF DSP & DAC TC94A15F

16.934MHz

A 3.3V

LIMIT SW

SLED MOTOR

SPDL MOTOR

DRIVE FPC

CP-51

PICK UP

DRIVE UNIT

CHANGER MECHANISM

MAIN PWB

PON1

SYS 9V

IC101 Tri-State Buffer

MOST ON

J101

M-D-GND SPDIF M-D-GND MO-STATUS MO-RESET MO-CS MO-ERROR MO-CLK MO-INT MO-RX MO-TX MO-AINT D-3.3V RMCK-SW GAIN-CON WAKE-UP VDD +B-DETECT TEMP_C RESET P-ON1 MOST_ON S-9V B/U GND M-D-GND RMCK M-D-GND

MOST CONNECTOR

P501

42:RX 3:TX

23:STATUS 31:RST 32:CS 37:ERROR 38:SDIN(RXD) 39:SCL 40:SDA(TXD) 41:INT 43:AINT

IC201 MOST-BUS TRANCEIVER OS8104

4:RMCK

15:SPDIF

12.288MHz

IC403 B/U DETECT

IC601 BA05ST MOST5V

IC301 SYS9V BA09ST

IC401 RESET IC

IC402 VDD 5V TDA3664

B/U 12V(J501)

TX RX WAKE GAIN

CONNECTOR PWB

Battery Gnd MOST-Tx MOST-Rx

BLOCK DIAGRAM

PU-2610A

pin 33: TESTR

EXPLANATION OF IC 051-5410-18

S-80820CNMC-8BF Precision Vlotage Down Detector 2.0V OUTPUT 1

5 N.C.

VDD GND

4 N.C.

Terminal description pin 1: OUTPUT pin 2: VDD pin 3: GND pin 4: NC pin 5: NC

051-5806-00

051-5831-90

2 3

: N channel open drain output, negative logic. : Positive supply voltage, negative logic input. : Ground. : Not in use. : Not in use.

GP1S94

Photo-interrupter 2

LM20BIM7

2.4V, 10ÎźA,

Temperature Sensor

The LM20 is a precision analog output CMOS integratedcircuit temperature sensor that operates over a -55 degree C to +130 degree C temperature range. Positive Supply Voltage 4 Ground 5

051-6399-00

TC94A15F

Terminal Description pin 1: IPF OUT pin 2: SB OK O pin 3: CLOCKIO pin 4: VDD pin 5: VSS pin 6: DATA pin 7: SF SY O pin 8: SB SY O pin 9: HSO pin 10: UHSO pin 11: AR SEL IN pin 12: AWRC pin 13: P VDD pin 14: PDO pin pin pin pin

15: TMAX S 16: TMAX 17: LPF N 18: LPF OUT

pin pin pin pin pin pin pin

19: P Vref 20: VCO FILTER 21: VCO Ref 22: DTC N 23: DTC P 24: PLL VSS 25: SLCO

pin pin pin pin

26: RF IN 27: RF RP 28: RF EQ OUT 29: A VDD

pin 30: RES IN pin 31: Vref OUT pin 32: VMDIR

PU-2610A

3 Sensed Voltage output 2 Ground 1 N.C.

CD IC

: O : IP flag output. : O : Sub code Q data CRCC OK signal output. :I/O: The clock pulse input/output for the sub code reading. : - : Positive supply voltage. : - : Negative supply voltage. : O : DATA : O : Playback frame synchronous signal output. : O : Sub code block synchronous signal output. : O : The play speed flag output. : O : The play speed flag output. : IN : Fix to the high level. : O : The control signal output for the active wide range VCO. : - : PLL positive supply voltage. : O : Phase difference signal output of EFMPLCK. : O : T max judgment output. : O : T max judgment output. : IN : Inverted input of LPF for PLL. : O : The output terminal for the Low Pass Filter. : - : PLL reference voltage. : O : Loop filter for VCO. : IN : VCO reference voltage input. : O : For the analog slicer. : O : For the analog slicer. : - : PLL ground. : O : Output of internal DAC for data slice level generation. : IN : RF signal input. : IN : RF ripple input. : O : The output of the RF equalizer. : - : Positive supply voltage for the Analog section. : - : For reference current setting. : O : The reference voltage output. : O : The reference voltage output.

pin pin pin pin pin

34: INVSEL 35: AGCI 36: RF DCI 37: RF OUT 38: PN SEL

pin pin pin pin pin pin pin pin pin pin pin pin pin pin pin pin

39: EQ SET 40: RF VDD 41: LDO 42: MDI 43: RF VSS 44: FNI 2 45: FNI 1 46: FPI 2 47: FPI 1 48: TPI 49: TNI 50: FTEO 51: RF ZI 52: A VSS 53: RF RP 54: RF DC

pin pin pin pin pin

55: FEI 56: SBAD 57: TEI 58: TE Z IN 59: A VDD

pin pin pin pin pin pin pin pin pin pin pin pin pin pin pin pin pin pin pin

60: FOO 61: TRO 62: Vref 63: FMO 64: DMO 65: IO2A 66: IO3A 67: MONIT 68: FG IN 69: VSS 70: VDD 71: TESIN 72: X VSS 73: X IN 74: X O 75: X VDD 76: D VSS 77: RO 78: D VDD

pin pin pin pin pin pin pin pin pin pin pin pin pin pin

79: D Vref 80: LO 81: D VSS 82: Z DET O 83: VSS 84: BUS 0 85: BUS 1 86: BUS 2 87: BUS 3 88: BU CK IN 89: CCEI 90: RSTI 91: VDD 92: EMPHI/FAO

pin 93: BCKI/FBO pin 94: AIN/FCO pin 95: LRCKI/FDO pin 96: EMPHO pin 97: B CK O pin 98: A OUT pin 99: LR CK O pin100: D OUT

-4-

: O : The compensation terminal for RFEQO offset. : IN : MDI polarity selection. : IN : The input terminal of RF AGC amplifier. : IN : The input terminal for RF peak detection. : O : RF signal output. : IN : The transistor type selection input for laser diode driver. L=NPN, H=PNP. : O : The equalizer setting terminal. : - : RF power supply. : O : The laser diode drive output. : IN : Monitor photo diode signal input. : - : RF ground. : IN : Main beam signal input. : IN : Main beam signal input. : IN : Main beam signal input. : IN : Main beam signal input. : IN : Sub beam signal input. : IN : Sub beam signal input. : O : For test. : IN : RF ripple zero cross signal input. : - : Analog ground. : O : RF ripple signal output. : O : RF peak detection signal output. (hologram suitable) : O : Focus error signal output. : O : Sub beam add signal output. : O : Tracking error signal output. : IN : Tracking error signal inpur for zero cross. : - : Positive supply voltage for the Analog section. : O : Focus equalizer output. : O : Tracking equalizer output. : O : Reference voltage output. : O : Field equalizer output / Speed error output. : O : Disk equalizer output. :I/O: General input/output. :I/O: General input/output. : O : Internal DSP signal monitor. : IN : FG input for the spindle CAV servo. : - : Negative supply voltage. : - : Positive supply voltage. : IN : For test. : - : Master clock analog ground. : IN : Crystal connection. : O : Crystal connection. : - : Clock power supply. : - : Digital ground. : O : Right channel data output for 1-bit DAC. : - : Positive supply voltage for the digital section. : O : Digital reference voltage. : O : Left channel data output for 1-bit DAC. : - : Digital ground. : O : 1bit DAC zero flag output. : - : Negative supply voltage. :I/O: CD IC Data input / output. :I/O: CD IC Data input / output. :I/O: CD IC Data input / output. :I/O: CD IC Data input / output. : IN : CD IC Data clock input. : IN : Chip enable input. : IN : Reset signal input. : - : Positive supply voltage. :I/O: Emphasis input for 1-bit DAC / Flag A output. :I/O: Bit clock input for 1-bit DAC / Flag B output. :I/O: Audio input for 1-bit DAC / Flag C output. :I/O: LR clock input for 1-bit DAC / Flag D output. : O : Emphasis flag output. H=Emphasis ON. : O : Bit clock output. : O : Audio signal output. : O : LR clock output. : O : Serial data output.

051-6632-08

OS8104 MOST(Media Oriented Systems Transport) Network transceiver device

Terminal Description pin 1: PAR SRC : IN : Parallel source data port select input. pin 2: P Address Sel 0: IN : Parallel address select input. pin 3: MOST TX : O : MOST transmitter output. pin 4: RM CK : O : Recovered master clock output. pin 5: D VDD : - : Positive supply voltage for the digital section. pin 6: D GND : - : Digital ground. pin 7: RAED : IN : Read enable input. pin 8: WRITE : IN : Write enable input. pin 9: D 0 / SX 0 :I/O: Parallel data i/o, Source Port data output. pin 10: D 1 / SX 2 :I/O: Parallel data i/o, Source Port data output. pin 11: P Address Sel 1: IN : Parallel address select input. pin 12: D 2 / SX 3 :I/O: Parallel data i/o, Source Port data output. pin 13: FSY :I/O: Frame sync i/o. pin 14: SCK/SRC FLOW:I/O: Serial clock i/o, Parallel data FIFO flow control output. pin 15: D 3 / SR 0 :I/O: Parallel data i/o, Source Port data input. pin 16: D 4 / SR 2 :I/O: Parallel data i/o, Source Port data input. pin 17: D 5 / SR 3 :I/O: Parallel data i/o, Source Port data input. pin 18: P VDD : - : Periphery power supply. pin 19: P GND : - : Periphery power ground. pin 20: XT I : IN : Oscillation terminal. pin 21: XT O : O : Oscillation terminal. pin 22: WAKEUP : O : Zero-Power mode wakeup time control. pin 23: STATUS : O : Power mode status. pin 24: R TIMER : IN : Wakeup timer resistor input. pin 25: Vref : - : Reference voltage. pin 26: FLT : IN : PLL loop filter input. pin 27: A GND : - : Analog ground. pin 28: A GND : - : Analog ground. pin 29: A VDD : - : Analog power supply. pin 30: A VDD : - : Analog power supply. pin 31: RESET : IN : Reset signal input. pin 32: AD 1 / CS IN : IN : Address input for IIC mode, Chip select input in SPI mode. pin 33: CP FLOW : O : Control port flow control indicator output. pin 34: ASYNC : IN : Asynchronous mode configuration pin. pin 35: D 6 / SR 1 :I/O: Parallel data i/o, Source Port data input. pin 36: D 7 / SX 1 :I/O: Parallel data i/o, Source Port data output. pin 37: ERROR : O : Error indicator output. pin 38: AD 0 / SD IN : IN : Address input for IIC mode, Serial data input in SPI mode. pin 39: SCL :I/O: IIC/SPI clock. pin 40: SDA / SD OUT :I/O: IIC data i/o, SPI data output. pin 41: INT :I/O: Control message and power-on interrupt pin. pin 42: MOST RX : IN : MOST receiver input. pin 43: A INT : O : Asynchronous message interrupt. pin 44: PAR CP : IN : Parallel control port select input.

051-6700-00

TMS320DA140PGE160

Terminal Description pin 1: VSS pin 2: Memo Addrss pin 3: VSS pin 4: VDD pin 5: Memo Addrss pin 6: C RESET pin 7: Memo Addrss pin 8: Memo Addrss pin 9: Memo Addrss pin 10: Memo Addrss pin 11: Memo Addrss pin 12: VDD pin 13: NU pin 14: VSS pin 15: VSS pin 16: VDD pin 17: NU pin 18: NU

Digital Signal Processor

: - : Negative supply voltage. 22: O : Control signal output for Memory IC. : - : Negative supply voltage. : - : Positive supply voltage. 10: O : Address output to Memory IC. : O : Reset pulse output to CD IC. 11: O : Address output to Memory IC. 12: O : Address output to Memory IC. 13: O : Address output to Memory IC. 14: O : Address output to Memory IC. 15: O : Address output to Memory IC. : - : Positive supply voltage. : IN : Not in use. : - : Negative supply voltage. : - : Negative supply voltage. : - : Positive supply voltage. : IN : Not in use. : IN : Not in use.

-5-

pin pin pin pin pin pin pin pin pin pin pin pin pin pin pin pin pin pin

19: READY 20: PS 21: NU 22: NU 23: WRITE ENBL 24: M STRB 25: NU 26: NU 27: LD CONT 28: NU 29: NU 30: NU 31: CS 32: NU 33: VDD 34: VSS 35: V BUS WUP 36: C BUS CE/TRB

: IN : The ready signal input. : O : Control signal output for Memory IC. : O : Not in use. : O : Not in use. : O : The write enable signal output. : O : Control signal output for Memory IC. : O : Not in use. : O : Not in use. : O : The loading control signal output. : O : Not in use. : O : Not in use. : IN : Not in use. : IN : The chip select command input. : - : Not in use. : - : Positive supply voltage. : - : Negative supply voltage. : IN : V BUS WUP input. :I/O: Data bus chip enable signal output to CD IC. Or mechanism sensor signal input. pin 37: VSS : - : Negative supply voltage. pin 38: C BUS CK/TRA :I/O: Data bus clock pulse output to CD IC. Or mechanism sensor signal input. pin 39: NU : IN : Not in use. pin 40: VSS : - : Negative supply voltage. pin 41: C BCK : IN : Bit clock pulse input from CD IC. pin 42: NU : O : Not in use. pin 43: C LRCK : IN : LR clock pulse input from CD IC. pin 44: NU : O : Not in use. pin 45: C SD : IN : Serial data input from CD IC. pin 46: NU : IN : Not in use. pin 47: MS SI : IN : Serial data input from Master Computer. pin 48: C DAC BCK : O : Bit clock output for the internal DAC of CD IC. pin 49: MS SCK : IN : Serial clock input from Master Computer. pin 50: VSS : - : Negative supply voltage. pin 51: NU : O : Not in use. pin 52: VDD : - : Positive supply voltage. pin 53: C DAC LRCK : O : LR clock output for the internal DAC of CD IC. pin 54: MS CS : IN : Chip select input from Master Computer. pin 55: NU : O : Not in use. pin 56: VDD : - : Positive supply voltage. pin 57: VSS : - : Negative supply voltage. pin 58: C BUS 0 :I/O: Data bus for CD IC. pin 59: C DAC SD : O : Serial data output for the internal DAC of CD IC. pin 60: MS SO : O : Serial data output to Master Computer. pin 61: NU : O : Not in use. pin 62: NU : IN : Not in use. pin 63: NU : IN : Not in use. pin 64: WUP : IN : V BUS WUP. pin 65: SBSY : IN : Sub code block synchronous signal detection input. pin 66: C BMOVF : IN : Buffer memory over flag input from CD IC. pin 67: SCK : IN : The clock pulse input. pin 68: VDD : - : Positive supply voltage. pin 69: C BUS 1 :I/O: Data bus for CD IC. pin 70: VSS : - : Negative supply voltage. pin 71: LIMIT : IN : Inside limit switch signal input for the pickup. pin 72: VSS : - : Negative supply voltage. pin 73: C PF/ CHUCK : IN : C2 correction data input from CD IC. Or chucking signal input from the mechanism. pin 74: LD MUTE : O : Muting signal output to the CD mechanism. pin 75: VDD : - : Positive supply voltage. pin 76: VSS : - : Negative supply voltage. pin 77: Clock Mode 1 : IN : Clock mode selection. pin 78: Clock Mode 2 : IN : Clock mode selection. pin 79: Clock Mode 3 : IN : Clock mode selection. pin 80: NU : IN : Not in use. pin 81: C BUS 2 :I/O: Data bus for CD IC. pin 82: NU : O : Not in use. pin 83: NU : IN : Not in use. pin 84: NU : O : Not in use. pin 85: NU : O : Not in use. pin 86: NU : IN : Not in use.

PU-2610A

SN74LVC139APWR Dual 2-line to 4-line Decoders/Demultiplexers

1 G_ 1A 1B 1 Y 0_ 1 Y 1_ 1 Y 2_ 1 Y 3_ GND

1 2 3 4 5 6 7 8

16 15 14 13 12 11 10 9

Logic

051-7518-18

Logic

pin 87: NU : IN : Not in use. pin 88: NU : IN : Not in use. pin 89: NU : IN : Not in use. pin 90: VSS : - : Negative supply voltage. pin 91: VDD : - : Positive supply voltage. pin 92: NU : IN : Not in use. pin 93: VSS : - : Negative supply voltage. pin 94: CLK OUT : O : Clock pulse output. pin 95: C BUS 3 :I/O: Data bus for CD IC. pin 96: NU : O : Not in use. pin 97: SYS CLK : IN : 16.92MHz pin 98: RESET : IN : Reset signal input. pin 99: Memo Data 0 :I/O: Parallel data input/output for Memory IC. pin100: Memo Data 1 :I/O: Parallel data input/output for Memory IC. pin101: Memo Data 2 :I/O: Parallel data input/output for Memory IC. pin102: Memo Data 3 :I/O: Parallel data input/output for Memory IC. pin103: Memo Data 4 :I/O: Parallel data input/output for Memory IC. pin104: Memo Data 5 :I/O: Parallel data input/output for Memory IC. pin105: Memo Addrss 16: O : Address output to Memory IC. pin106: VSS : - : Negative supply voltage. pin107: Memo Addrss 17: O : Address output to Memory IC. pin108: Memo Addrss 18: O : Address output to Memory IC. pin109: Memo Addrss 19: O : Address output to Memory IC. pin110: Memo Addrss 20: O : Address output to Memory IC. pin111: VSS : - : Negative supply voltage. pin112: VDD : - : Positive supply voltage. pin113: Memo Data 6 :I/O: Parallel data input/output for Memory IC. pin114: Memo Data 7 :I/O: Parallel data input/output for Memory IC. pin115: Memo Data 8 :I/O: Parallel data input/output for Memory IC. pin116: Memo Data 9 :I/O: Parallel data input/output for Memory IC. pin117: Memo Data 10 :I/O: Parallel data input/output for Memory IC. pin118: Memo Data 11 :I/O: Parallel data input/output for Memory IC. pin119: Memo Data 12 :I/O: Parallel data input/output for Memory IC. pin120: CN VCC : IN : Connect to VCC. pin121: Memo Data 13 :I/O: Parallel data input/output for Memory IC. pin122: Memo Data 14 :I/O: Parallel data input/output for Memory IC. pin123: Memo Data 15 :I/O: Parallel data input/output for Memory IC. pin124: SRQ : O : V BUS SRQ output. pin125: VDD : - : Positive supply voltage. pin126: VSS : - : Negative supply voltage. pin127: NU : IN : Not in use. pin128: VSS : - : Negative supply voltage. pin129: NU : IN : Not in use. pin130: VDD : - : Positive supply voltage. pin131: Memo Addrss 0: O : Address output to Memory IC. pin132: Memo Addrss 1: O : Address output to Memory IC. pin133: Memo Addrss 2: O : Address output to Memory IC. pin134: Memo Addrss 3: O : Address output to Memory IC. pin135: SYS POWER : O : System power supply control signal output. pin136: Memo Addrss 4: O : Address output to Memory IC. pin137: Memo Addrss 5: O : Address output to Memory IC. pin138: Memo Addrss 6: O : Address output to Memory IC. pin139: Memo Addrss 7: O : Address output to Memory IC. pin140: Memo Addrss 8: O : Address output to Memory IC. pin141: Memo Addrss 9: O : Address output to Memory IC. pin142: VDD : - : Positive supply voltage. pin143: Memo Addrss 21: O : Control signal output for Memory IC. pin144: VSS : - : Negative supply voltage.

VCC 2 G_ 2A 2B 2 Y 0_ 2 Y 1_ 2 Y 2_ 2 Y 3_

Truth Table G_

Y 0_

Y 1_

Y 2_

Y 3_

don't care

051-9402-78

BR93L56RFVM-W

Terminal Description pin 1: CS pin 2: S CLCK pin 3: S DI pin 4: S DO pin 5: GND pin 6: NU pin 7: NU pin 8: VCC

-6-

128 x 16bit EEPROM

CS 1 S CLCK 2

8 VCC 7 NU

S DI 3 S DO 4

6 NU 5 GND

: IN : The chip select command input. : IN : Serial clock input. : IN : Serial data input. : O : Serial data output. : - : Ground. : - : Not in use. : - : Not in use. : - : Positive supply voltage.

EXPLODED VIEW / PARTS LIST Main section 17

23 20

24 21 16

29 25

28 12 3 11 14

2 6

7 27

1-1

13 10

1-3 1-2 1

4 5 25

NO. 1

PART NO.

DESCRIPTION

Q'TY

NO.

PART NO.

DESCRIPTION

Q'TY

940-7993-20 ESCUTCHEON-ASSY

622-1545-20 FL PIN R

1-1

320-0591-24 DUSTPROOF-CVR

622-1546-20 FL PIN L

1-2

320-0592-24 DUSTPROOF-CVR

629-0080-00 DAMPER

1-3

370-9610-23 ESCUTCHEON

750-3459-21 FL-SPRING R

-----------

750-3460-21 FL-SPRING L

310-1757-10 UPPER CASE

-----------

311-1856-10 LOWER CASE

074-1293-01 OUTLET SOCKET

347-7216-00 PROTECTOR

074-1294-00 OUTLET SOCKET

371-5693-22 TRIM PLATE

331-3386-00 TR-HOLDER

382-6254-20 BUTTON

345-5193-00 ABSORPTION SHEET

620-0996-21 DAMPER PLATE R

313-1859-00 HEAT SINK

620-0997-20 DAMPER PLATE F

331-3404-01 CONN-BRKT

039-2152-01 FPC(WITHOUT COMPONENT)

CD CHANG-MECHANISM (028520)

-7-

CONNECTOR PWB

PU-2610A

NO.

DESCRIPTION

Q'TY

NO.

714-2608-81 MACHINE SCREW(M2.6 x 8)

PART NO.

746-0767-00 SPECIAL WASHER

DESCRIPTION

Q'TY 2

716-1494-00 IT SCREW(M2.6 x 6)

285-1939-00 GUIDE LABEL

716-1716-00 SCREW(M2 x 2.5)

716-3486-00 SPECIAL SCREW

286-6306-01 SETPLATE(PU2610AA) 286-6306-02 SETPLATE(PU2610AB)

Note)Only setplates differ in Main section. The model name is specified in the description.

CD changer mechanism section 55 10

36 A7

B7 B6

B10

34 D1

N1 A11

E1 E

A10

A14

1 2 3

4 5 6

A14

A13

A12

A10

62 A5

2 3

4 5 6

51 65 45 65

A9 A13

54 57

A12

NO.

PART NO.

A11

Q'TY

NO.

966-0582-23 DRIVE-P-ASSY

966-0583-20 DISC HOLD-ASSY

966-0591-21 REAR PANEL-ASSY

966-0584-23 CLAMP-P-ASSY F

966-0592-20 UP-PLATE-ASSY

966-0585-22 CAM GEAR-ASSY

966-0593-20 UD-GEAR-P-ASSY

966-0586-22 MOTOR-P-ASSY

966-0594-24 V-CHASSIS-ASSY

966-0588-23 HOLDER-L-ASSY

966-0454-00 SH-RACK-ASSY

966-0589-24 L-UPPER-P-ASSY

966-0623-23 L-LOWER-P-ASSY

PU-2610A

DESCRIPTION

-8-

PART NO.

DESCRIPTION

966-0590-20 MG-LO-P-ASSY

Q'TY 1

29 O1

F2 F1

66 G1 G1

55 G2

41 60

48 J2

J1 J3

5 K3

PART NO.

DESCRIPTION

43 57 20

61 58 37

13 15 P1

NO.

57 39 25 56 40

H2 M2

57 Q1

64 71

P1 K1

N1 J4 N2

55 K3

65 65 49 E1 L1

24 17

26 I1

O1 G2

Q'TY

NO.

969-0066-30 PICK UP-ASSY

620-1020-21 SLIDE PLATE F

-----------

620-1031-22 LOADING ARM

MAIN PWB

PART NO.

DESCRIPTION

Q'TY

001-0563-00 LED

620-1034-24 SIDE PANEL

013-7413-50 DETECTOR SWITCH

621-0587-21 SCREW HOLD BASE

SMA-180-100 MOTOR-ASSY(UP/DOWN)

801-4912-60 VINYL-COAT-WIRE(BRN)

SMA-181-100 MOTOR-ASSY(SLED)

621-0589-20 SECOND GEAR

SMA-179-100 MOTOR-ASSY(SPINDLE)

621-0590-20 LS GEAR

039-1949-21 DRIVE FPC (WITHOUT COMPONENT)

621-0591-20 PICK UP GUIDE

039-1950-21 LOADING FPC (WITHOUT COMPONENT)

621-0592-21 LS-HOLDER

621-0593-21 LS GUIDE

060-0252-01 PHOTO-TR

802-4906-60 VINYL-COAT-WIRE(RED)

620-0999-21 LS-SPRING

621-0423-00 V-GEAR A

620-1575-22 SWITCH PLATE

621-0630-22 HOLDER-G-RAIL R

620-1007-23 CLAMP PLATE M

621-0631-21 HOLDER-G-RAIL L

620-1008-24 CLAMP PLATE R

621-0703-20 L-GEAR A

620-1009-22 CLAMPER PLATE

621-0633-20 L-GEAR B

620-1016-20 GAP PLATE R

805-4912-60 VINYL-COAT-WIRE(GRN)

620-1017-20 GAP PLATE F

621-0635-20 V-HELICAL GEAR

620-1018-20 MG EJECT PLATE

621-0636-21 CLAMPER RING

620-1019-20 SLIDE PLATE R

624-3022-00 LEAD SCREW

-9-

PU-2610A

NO.

Q'TY

NO.

629-0061-00 GEAR DAMPER

PART NO.

DESCRIPTION

PART NO.

745-0789-01 DRIVE WASHER

DESCRIPTION

Q'TY 2

716-0484-00 SCREW(M2 x 2.5)

746-0761-00 WASHER

716-0675-00 SCREW(M2 x 5.5)

750-3461-21 DISC-H-SPRING

716-1716-00 SCREW(M2 x 3)

750-3462-21 GAP SPRING

716-3469-00 SCREW(M1.7 x 4)

750-3463-20 MG LOCK SPRING

735-2006-11 D-SEMS-SCREW(M2 x 6)

750-3464-20 MG EJECT SPRING

739-1722-17 SCREW(M1.7 x 2.2)

750-3492-22 CLAMPER SPRING

739-2022-17 SCREW(M2 x 2.2)

716-1799-10 SPECIAL SCREW(M2 x 2.5)

743-1500-10 E-RING

800-4906-60 VINYL-COAT-WIRE(BLK)

743-2000-10 E-RING

SMA-188-100 MOTOR-ASSY(LOADING)

ELECTRICAL PARTS LIST Connector PWB(B1) section REF No. C101 C102 C201 C202 C203 C204 C205 C206 C207 C208 C209 C210 C211 C212 C213 C301 C302 C303 C401 C403 C404 C405 C406 C408 C409 C410 C501 C502 C503 C504 C505 C506 C507

PART No. 168-1042-78 045-1011-50 163-1063-35 168-1042-78 168-1042-78 163-1063-35 168-1042-78 168-1042-78 163-1063-35 168-1042-78 045-2201-50 045-2201-50 168-1042-78 168-1022-55 168-1042-78 178-3342-78 163-2273-25 168-1042-78 168-2245-79 163-2273-25 046-1032-78 042-0427-94 046-1032-78 046-1032-78 046-1022-58 163-4763-35 189-3383-42 043-0499-51 163-1073-15 168-1042-78 163-1073-15 168-1042-78 172-1031-11

DESCRIPTION 16V 0.1uF 100pF 16V10uF 16V 0.1uF 16V 0.1uF 16V10uF 16V 0.1uF 16V 0.1uF 16V10uF 16V 0.1uF 22pF 22pF 16V 0.1uF 1000pF 16V 0.1uF 0.33uF 10V 220uF 16V 0.1uF 0.22uF 10V 220uF 0.01uF 16V47uF TAN 0.01uF 0.01uF 1000pF 16V47uF 25V3300uF 0.1uF 6.3V100uF 16V 0.1uF 6.3V100uF 16V 0.1uF 0.01uF

REF No. C508 C509 C510 C511 C512 C513 C601 C602 C603 C604 C605 D401 D501 IC101 IC201 IC301 IC401 IC402 IC403 IC601 J101 J501 L101 L201 L501 L502 P501 Q101 Q501 Q502 R101 R102 R103

PART No. 166-1021-56 045-1011-50 168-1042-78 045-1011-50 168-1042-78 043-0546-50 178-3342-78 163-2273-25 168-1042-78 042-0423-97 042-0403-57 001-2403-90 001-2015-00 051-6919-08 051-6632-08 051-3289-00 051-1556-09 051-3298-90 051-1556-09 051-3260-00 074-1189-90 074-1293-01 010-3110-50 010-2285-64 010-2285-64 010-2285-64 074-1294-00 192-2712-00 125-2004-92 125-0002-92 033-4731-15 033-1031-15 033-1031-15

DESCRIPTION 1000pF 100pF 16V 0.1uF 100pF 16V 0.1uF 0.1uF 0.33uF 10V 220uF 16V 0.1uF 16V10uF 35V 10uF M1F60 RL253 NJU6391PE-TE1 OS8104 BA09ST S-80840CNUA-B8Z TDA3664/N1 S-80840CNUA-B8Z BA05ST 40P 4P BK1608LM252 BLM11A102SPB BLM11A102SPB BLM11A102SPB 8P 2SC2712 RN1402 RN2402 1/10W 47k ohm 1/10W 10k ohm 1/10W 10k ohm

CD changer mechanism section Main PWB(B2) section REF No. C1 C2 C3 C4 C5 C6 C8 C10 C11 C12 C13 C14 C15 C16

PART No. 046-4722-58 168-1042-78 046-1032-78 168-1042-78 168-1042-78 046-1032-78 168-1042-78 168-1042-78 163-1073-35 168-4732-78 168-4732-78 168-1042-78 178-1052-78 045-4701-50

PU-2610A

DESCRIPTION 4700pF 16V 0.1uF 0.01uF 16V 0.1uF 16V 0.1uF 0.01uF 16V 0.1uF 16V 0.1uF 16V100uF 0.047uF 0.047uF 16V 0.1uF 1uF 47pF

REF No. R104 R201 R202 R203 R204 R205 R206 R207 R208 R209 R401 R402 R403 R404 R405 R406 R501 R502 R503 R504 R505 T501 TM101 TM102 TM103 TM201 TM202 TM203 TM204 TR501 X201 PWB

PART No. 033-4711-15 033-4721-15 033-1011-15 033-4721-15 033-1511-15 033-1011-15 033-2221-15 033-3941-15 033-1031-15 033-0000-05 033-2241-15 033-0000-05 033-2241-15 116-2291-15 033-2241-15 033-5641-15 033-3331-15 033-3331-15 033-1511-15 033-1031-15 033-0000-05 009-9006-20 073-0762-90 073-0762-90 073-0762-90 073-0766-90 073-0766-90 073-0766-90 073-0766-90 010-3401-90 061-1080-00 039-2419-01

DESCRIPTION 1/10W 470 ohm 1/10W 4.7k ohm 1/10W 100 ohm 1/10W 4.7k ohm 1/10W 150 ohm 1/10W 100 ohm 1/10W 2.2k ohm 1/10W 390k ohm 1/10W 10k ohm 1/10W 0 ohm 1/10W 220k ohm 1/10W 0 ohm 1/10W 220k ohm 1/4W 2.2 ohm 1/10W 220k ohm 1/10W 560k ohm 1/10W 33k ohm 1/10W 33k ohm 1/10W 150 ohm 1/10W 10k ohm 1/10W 0 ohm CHOKE TERMINAL TERMINAL TERMINAL TERMINAL TERMINAL TERMINAL TERMINAL SBS9080-509T 12.288MHz PWB(WITHOUT COMPONENT)

Note)Some parts depend on each model. The model name is specified in the description. REF No. C17 C18 C19 C20 C21 C22 C23 C24 C27 C30 C31 C32 C33 C34

PART No. 046-1032-78 045-4701-50 046-4712-58 168-1042-78 046-1532-78 168-1042-78 046-6822-58 046-1032-78 046-3332-78 046-4722-58 046-1522-58 168-1042-78 046-1532-78 168-1042-78

DESCRIPTION 0.01uF 47pF 470pF 16V 0.1uF 0.015uF 16V 0.1uF 6800pF 0.01uF 0.033uF 4700pF 1500pF 16V 0.1uF 0.015uF 16V 0.1uF

- 10 -

REF No. C35 C36 C37 C38 C39 C40 C41 C42 C43 C44 C45 C46 C48 C51

PART No. 168-1042-78 163-4763-15 178-1052-78 045-6801-50 168-1042-78 168-1042-78 046-6812-58 178-1052-78 163-4763-15 168-1042-78 163-1073-15 163-1073-15 168-1042-78 046-1032-78

DESCRIPTION 16V 0.1uF 6.3V47uF 1uF 68pF 16V 0.1uF 16V 0.1uF 680pF 1uF 6.3V47uF 16V 0.1uF 6.3V100uF 6.3V100uF 16V 0.1uF 0.01uF

REF No. C52 C53 C54 C56 C57 C58 C59 C101 C102 C103 C104 C105 C106 C107 C108 C109 C110 C111 C112 C113 C114 C115 C116 C117 C118 C119 C120 C121 C122 C124 C125 C126 C127 C128 C130 C201 C202 C203 C204 C207 C208 C209 C210 C211 C212 C213 C215 C218 C219 C220 C221 C222 C223 CCT1 CCT2 CCT4 CCT5 CCT102 D1 D202 IC1 IC2 IC3 IC4 IC5 IC11 IC101

PART No. 046-1032-78 046-1032-78 046-1032-78 178-1052-78 178-1052-78 163-4763-15 042-0416-57 168-1042-78 168-1042-78 168-1042-78 168-1042-78 168-1032-55 168-1042-78 046-1032-78 163-4763-15 178-1052-78 046-1032-78 168-1042-78 168-1042-78 168-1042-78 046-1032-78 042-0416-57 046-1032-78 168-1042-78 045-1201-50 046-1032-78 046-1032-78 168-1042-78 046-1032-78 168-1032-55 046-1032-78 168-1032-55 168-1042-78 042-0416-52 042-0416-52 168-1042-78 163-4763-35 046-1032-78 168-1042-78 178-1052-78 178-1052-78 046-1032-78 168-1042-78 168-1042-78 168-1042-78 168-1042-78 163-4763-15 178-3342-78 163-4763-15 046-1032-78 042-0416-57 042-0423-97 163-3363-25 050-0140-68 050-0140-63 050-0140-54 050-0140-54 050-0140-63 001-0367-91 001-0367-91 051-6399-00 051-6060-08 051-5806-00 051-3293-90 051-5410-18 051-7221-58 051-7518-18

DESCRIPTION REF No. 0.01uF IC102 0.01uF 0.01uF 1uF 1uF IC103 6.3V47uF IC104 10V47uF M TAN IC105 16V 0.1uF IC106 16V 0.1uF IC107 16V 0.1uF IC201 16V 0.1uF IC203 0.01uF IC204 16V 0.1uF IC205 0.01uF IC206 6.3V47uF IC207 1uF J1 0.01uF J2 16V 0.1uF J3 16V 0.1uF J4 16V 0.1uF J5 0.01uF L1 10V47uF M TAN L2 0.01uF L3 16V 0.1uF L4 12pF L5 0.01uF L6 0.01uF L7 16V 0.1uF L8 0.01uF L9 0.01uF L10 0.01uF L11 0.01uF L12 16V 0.1uF L13 10V10uF M TAN L14 10V10uF M TAN L15 16V 0.1uF L101 16V47uF L102 0.01uF L103 16V 0.1uF L104 1uF L105 1uF L106 0.01uF L301 16V 0.1uF Q1 16V 0.1uF Q4 16V 0.1uF Q203 16V 0.1uF Q204 6.3V47uF R1 0.33uF R2 6.3V47uF R3 0.01uF R4 10V47uF M TAN R5 16V10uF R7 10V33uF R8 1/32W 3.3k ohm x4J R9 1/32W 47k ohm x4J R10 1/32W 1k ohm x4J R11 1/32W 1k ohm x4J R12 1/32W 47k ohm x4J R13 1SS226 R14 1SS226 R15 TC94A15F R16 BD7961FM-E2 R17 GP1S94 R18 BA033SFP-E2 R19 S-80820CNMC-8BF R20 SN74AHC1G04HDCKR R21 SN74LVC139APWR R22

PART No. DESCRIPTION REF No. R27 052-5063-00 MBM29DL800BA90PFTN(PU2610AA) R101 R102 052-5063-01 MBM29DL800BA90PFTN(PU2610AB) R103 051-7518-18 SN74LVC139APWR R104 R105 051-9330-00 K4S641632F-TC60 R107 051-7203-48 SN74LV74APW 051-6700-00 TMS320DA140PGE160 R108 R109 051-3315-90 TPS76316DBVR 051-9402-78 BR93L56RFVM-WE2 R110 R111 051-3260-00 BA05ST R112 052-0311-00 M30624FGAGP R113 051-5831-90 LM20BIM7 R114 051-7511-38 TC74LCX07FTEL R115 051-7239-38 SN74AHCT08PWR R116 074-1138-65 15P R117 074-1158-56 6P R118 074-1158-58 8P R119 074-1205-90 40P R120 074-1313-68 18P R121 010-3105-62 MMZ1608S1 R122 010-3105-62 MMZ1608S1 R123 010-3105-62 MMZ1608S1 R124 010-3300-50 MZA2010D330 R125 010-3300-50 MZA2010D330 R126 010-3300-50 MZA2010D330 R127 010-3300-50 MZA2010D330 R206 010-3300-50 MZA2010D330 R207 010-3300-50 MZA2010D330 R208 010-3300-50 MZA2010D330 R209 010-3300-50 MZA2010D330 R210 010-3300-50 MZA2010D330 R211 010-3300-50 MZA2010D330 R212 010-3300-50 MZA2010D330 R213 010-3105-62 MMZ1608S1 R214 010-3104-50 MPZ1608S3 R215 010-3104-50 MPZ1608S3 R216 010-3104-53 MPZ1608S2 R217 010-3104-53 MPZ1608S2 R218 010-3105-69 MMZ1608D800B R219 010-3105-69 MMZ1608D800B R220 010-3104-53 MPZ1608S2 R221 131-1188-50 2SB1188PQR R222 125-2004-91 RN1401 R223 131-1188-50 2SB1188PQR R224 125-2004-92 RN1402 R225 033-1021-15 1/10W 1k ohm R226 033-1021-15 1/10W 1k ohm R227 033-6811-15 1/10W 680 ohm R236 033-1051-15 1/10W 1M ohm R238 033-0000-05 1/10W 0 ohm R239 033-5621-15 1/10W 5.6k ohm R240 033-4731-15 1/10W 47k ohm R241 033-3341-15 1/10W 330k ohm R242 033-2231-15 1/10W 22k ohm R400 033-2231-15 1/10W 22k ohm R401 117-1001-15 1/8W 10 ohm S1 033-1031-15 1/10W 10k ohm S2 033-1031-15 1/10W 10k ohm S3 033-1531-15 1/10W 15k ohm X2 033-2231-15 1/10W 22k ohm X202 033-2211-15 1/10W 220 ohm Z101 117-2711-15 1/8W 270 ohm PWB 033-1031-15 1/10W 10k ohm 033-2721-15 1/10W 2.7k ohm 033-3331-15 1/10W 33k ohm 033-1031-15 1/10W 10k ohm

- 11 -

PART No. 033-1021-15 033-1031-15 033-1041-15 033-1021-15 033-1021-15 033-4731-15 033-4731-15 033-1041-15 033-4721-15 033-4721-15 033-4731-15 033-1021-15 033-1021-15 033-1021-15 033-4731-15 033-4731-15 033-1031-15 033-2211-15 033-1031-15 033-1021-15 033-4731-15 033-4701-15 033-4701-15 033-4701-15 033-4701-15 033-4701-15 033-4701-15 033-4721-15 033-4721-15 033-1011-15 033-1011-15 033-4731-15 117-2711-15 033-1041-15 033-4731-15 033-4731-15 033-4721-15 119-4741-15 033-4711-15 119-2231-15 033-4731-15 033-4731-15 033-1041-15 033-4711-15 033-4711-15 033-4711-15 033-4711-15 033-4711-15 033-4731-15 119-4711-15 119-1811-15 032-0140-18 032-0140-17 119-4741-15 119-2241-15 116-0000-05 117-0000-05 013-7404-50 013-7404-50 013-6100-10 060-1535-90 060-1542-90 060-8048-00 039-2420-01

DESCRIPTION 1/10W 1k ohm 1/10W 10k ohm 1/10W 100k ohm 1/10W 1k ohm 1/10W 1k ohm 1/10W 47k ohm 1/10W 47k ohm 1/10W 100k ohm 1/10W 4.7k ohm 1/10W 4.7k ohm 1/10W 47k ohm 1/10W 1k ohm 1/10W 1k ohm 1/10W 1k ohm 1/10W 47k ohm 1/10W 47k ohm 1/10W 10k ohm 1/10W 220 ohm 1/10W 10k ohm 1/10W 1k ohm 1/10W 47k ohm 1/10W 47 ohm 1/10W 47 ohm 1/10W 47 ohm 1/10W 47 ohm 1/10W 47 ohm 1/10W 47 ohm 1/10W 4.7k ohm 1/10W 4.7k ohm 1/10W 100 ohm 1/10W 100 ohm 1/10W 47k ohm 1/8W 270 ohm 1/10W 100k ohm 1/10W 47k ohm 1/10W 47k ohm 1/10W 4.7k ohm 1/10W 470k ohm 1/10W 470 ohm 1/10W 22k ohm 1/10W 47k ohm 1/10W 47k ohm 1/10W 100k ohm 1/10W 470 ohm 1/10W 470 ohm 1/10W 470 ohm 1/10W 470 ohm 1/10W 470 ohm 1/10W 47k ohm 1/10W 470 ohm 1/10W 180 ohm 1/10W 680k ohm 1/10W 270k ohm 1/10W 470k ohm 1/10W 220k ohm 1/4W 0 ohm 1/8W 0 ohm JW DETECTOR SW DETECTOR SW SKHLLD 16.934MHz 16MHz NOISE SHEET PWB(WITHOUT COMPONENT)

PU-2610A

Loading FPC(B3) section REF No. D501 Q501 S501

PART No. 001-0563-00 060-0252-01 013-7413-50

DESCRIPTION LED PT4850F DETECTOR SW

REF No. PART No. DESCRIPTION S502 013-7413-50 DETECTOR SW FPC 039-1950-21 FPC(WITHOUT COMPONENT)

Drive FPC(B4) section REF No. PART No. DESCRIPTION S503 013-7413-50 DETECTOR SW FPC 039-1949-21 FPC(WITHOUT COMPONENT)

PU-2610A

- 12 -