Fans Technical Catalogue
General data Labeling Labelling a fan as either ErP2013 or ErP2015 compliant indicates that it is compliant with the minimum requirements set forth in the respective Commission Regulation EU No 327/2011. The actual energy efficiency level of the fan used for the ErP rating is noted as nstat A. In order to comply with the requirements set forth in the ErP regulation, this energy efficiency level has to reach a specific minimum value (target energy level). The efficiency grade N is a parameter used in the calculation of the target energy efficiency as defined in Annex II of Commission Regulation EU No. 327/2011. Any and all data pertaining to ErP refer to measurement data established using the Hidria standard full bell mouth, and is based on a drawing and measurement table without guard grille. Actual efficiency level for every and each particular fan are published at Hidria web site www.hidria.com.
Aerodynamics and Acoustics Measurement method The ‘characteristic curve’ diagram shows the pressure increase Δps in Pa as a function of the volume flow rate qV in m3/h. The specified performance data meets the requirements according to accuracy class 3, compliant with DIN 24 166, and applies to the rated data and air performance curves at the rated voltage, air density of 1,2 kg/ m3 and at 20°C ambient temperature. The continuous line in the characteristic map represents the optimum reliable operating range for axial fans.
2
Fan test-bench The fan characteristic curves are determined on a combined ventilation and sound reverberant room test-bench. The characteristic curves are measured in compliance with DIN EN ISO 5801. The sound power levels are measured in reverberant room in compliance with DIN EN ISO 3743. The fan is attached to the measuring chamber with free (air) intake and (air) outlet (installation type A in compliance with DIN EN ISO 5801). Unless otherwise indicated, this catalogue specifies the intake side A-evaluated sound power levels LWA. The standard measurements are carried out without the need for additional parts, e.g. guard grille. The A-weighted sound power level is the standard variable used to assess the sound characteristics of technical equipment. General notes The information and data contained in this catalogue were composed to the best of our ability and do not absolve the user from its duty to verify the suitability of the products with respect to its intended application. Hidria reserves the right to make design changes, which are used for continuous performance and/or safety improvement.
02. AC Axial fans – Sickled blades
26
06. Accessories
134
Accessories
124
07. Connection diagrams
142
Connection diagramS
05. AC Radial fans Backward curved blades
74
AC axial fans Paddle blades
04. AC Axial fans – Paddle blades
60
AC radial fans backward curved blades
03. AC Axial fans – Plastic blades
Connecting diagram 0301-1-0034 MOTOR
GREEN/YELLOW BLACK
W1
GREY
U2
BROWN
L1
U1
ORANGE
TB
L2
V1
RED
TB
L3
V2
BLUE
W2
WHITE
TK
WHITE
TK
CONTROL UNIT
CONNECTION OPTIONS: L1 L2 L3 PE Protection device TK , TK
U1 V1 W1 PE U1 V1 W1 PE
TK , TK
Join together [U2.V2,W2] [U1,W2]; [V1,U2]; [W1,V2]
Winding connection STAR (Y) high voltage (STANDARD) DELTA (Δ)low voltage
* CHANGING OF ROTATION DIRECTION BY INTERCHANGING OF 2 PHASES! * TEMPERATURE MONITORS (TK) BUILT IN TO THE WINDING SERVE AS MOTOR CUT-OUT SWITCH AND MUST BE CONNECTED TO THE OUTSIDE CONTROL UNIT!
EC axial fans
04
AC axial fans Sickled blades
01. EC Axial fans
AC axial fans Plastic blades
Page
3
01 EC Axial fans
4
AC axial fans Paddle blades
AC axial fans Plastic blades
AC axial fans Sickled blades
EC axial fans
EC Axial fans
AC radial fans backward curved blades
EC Axial fans
Connection diagramS
Accessories
XXX Arciis erchic temolor empeles nam, quo tectorehenem fuga. Nam as simagniscia aut repelist quam sa que occae. Nemporionse volum none sam, sequae natur sus etur, nihil ipis aut es seque nations ecescit voluptatent ma nos aut ex et volorepedis et aut ut lamus et porem escit, earum.
5
EC Axial fans
EC Axial fans ■■ Electrical connection and motor The three-phase or single phase EC (Electronically Commutated) external rotor permanent magnet integrated into the fan hub meets the requirements for circulating electric machines according to EN 60335-2-80:2003. The rated voltage for a three-phase power supply is 400 V and for single-phase it is 230 V. The EC motors are suitable for power network with single phase voltage range 200.277 V 50/60 Hz or three-phase 380-480V 50/60Hz. Refer to the data sheet of each fan for the details.
■■ Motor connection Mains connection is made via terminal box or outgoing connection cable as shown in dimensional drawings. The standard version of an EC fan has: • • • • •
1 or 3 phase line, N – neutral, G- ground, analog input (0-10 V or PWM), SELV power supply 10 VDC (max. 30 mA), • Tach out or error out signal (programmable), Reference control signal is optional when build in PID controller is required.
■■ Terminal box and connection cable Terminal boxes are made of shock-proof and weather-resistant plastics. Heat and UV resistant halogen-free hose cables are used, marked by a color code or connection designations as labeled on to terminal block. The cable construction complies with VDE 0282 Part 804 and is suitable for operating voltages of up to 400 V for single phase products and 690 V for tri phase products.
■■ Speed controls Hidria EC fans are made with integrated electronic variable speed drive (VSD). Speed variation can be made by speed input signal 0V to 10 VDC, 4-20 mA or Pulse 6
Width Modulated(PWM) frequency signal. Please read EC fan safety, installation and maintenance instructions prior any of these actions is to be taken.
condensation drain hole must be open when the fan is installed with the rotor at the bottom. With horizontal mounting position condensate can escape via the gap between stator and rotor. Fans suitable
■■ Installation and usage information
for installation with rotor at the top (connection box or cables at the bottom) or at any other angle are available only on request.
For the installation, maintenance and safe usage of EC axial fans, please refer to user manual.
■■ Materials and corrosion protection Hidria EC Axial fan impellers are made of high-performance PA composite material or steel. The impeller is pressed onto the rotor. The stator flange is made of hi-pressure die-casted seawater resistant aluminum alloy. Rotors and fan nozzles are made of steel sheet and coated to meet resistance to corrosion as set by ISO 12944-2 class C3 (medium). Additional coating on request and at supplementary cost. The wire protection grilles have a weather resistant plastic coating.
Operating mode Continuous operation (S1). Use speed control input signal when On/Off cycling of EC fan is required. Power supply cycling is allowed only at certain conditions. See EC fan User Manual.
Resistance to water, dust and moisture Majority of axial fans are resistant to presence of water, dust and moisture as defined by class IP44 or IP 54 (IEC 60529, IEC60034, IEC60335).
Ambient conditions If not instructed differently the fans can be subjected to the following conditions:
■■ Operating conditions and product life
• Placed outdoors (rain, snow, UV radiation). • Working ambient temperatures between -25°C and +65°C. • Storage temperatures -40°C to +80°C.
Safety
Product life
The fans may only be operated when they are installed as intended and when safety is ensured by safety equipment according to DIN EN 294 resp. ISO13852 (DIN EN ISO 12100) or by other protection measures.
Safety approvals Depending on the product, Hidria fans comply with the one or more of the following standards: EN 60335-1, EN 61800-5-1 and EN 60034-1. All EC fans can be supplied with CE approvals. UL/ CSA, CCC and/or GOST approvals on request. All EC fans meet requirements of EU Directives ROHS 2002/95/EC and REACH 1907/2006/EC.
Condensation drain holes EC fans are intended to be installed with rotor in horizontal position or with rotor at the bottom of the fan (connection box or cables on the top). The lower of the
By utilizing lifetime maintenance free bearings, our EC axial fans are maintenance free for the entire life time of approximately 30-40.000 hours for standard applications and environmental conditions. Contact protection The preferred “protective construction” used on axial fans is a guard grille. Depending on the airflow direction, the guard grille is located on the intake or pressure side of the fan. The “Accessories” section contains separate guard grilles, which can be positioned on the pressure or intake side of the fan as required and depending on the installation situation, to meet the safety requirements set out in DIN EN ISO 13857, defining safety distance requirements to prevent upper limbs from getting into hazardous areas. The guard grille results in a resistance to the conveyed airflow, which manifests itself in the pressure loss.
EC Axial fans
AC axial fans Sickled blades
EC axial fans
Axial fans with electronically comutated (EC) motors Stamped metal blades (type 30H)
AC axial fans Plastic blades
Diameters: 300-350 mm
Plastic blades (type AP, LP)
AC axial fans Paddle blades
Diameters: 400-500 mm
Plastic blades (type LP)
AC radial fans backward curved blades
Diameters: 560-630 mm
Example of type key:
R10R-40APS-ES50B-02A01 R10 External rotor motor type (R09, R10) R Acessory type (E ‒ without guard grill, R ‒ with guard grill, P ‒ with guard grill and wall plate) 40 Fan diameter x 10 (exact diameters are stated in drawings)
Accessories
AP Type of blabes (30H, AP, LP) S Airflow direction (S ‒ sucking, B ‒ blowing) E Fan motor type (E ‒ fan with electronically comutated motor and integrated VSD) S Electrical connection (S ‒ single phase) 50 Motor stack height
Connection diagramS
B Type of connecting (B ‒ connection box with terminal block, C ‒ cable) 02 Version of motor construction A Version of electronical controller 01 Settings of electronical controller
7
EC Axial fans
Diameter:
300 mm
R09_-3030H_-ES25C-01A04
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230V
Nominal voltage range
230 V
Frequency
50-60Hz
Input power
80 W
Input current
0.64 A
Nominal speed
1650 RPM
Min. ambient temperature
-25 째C
Protection class
IP44
Insulation class
130
ErP data according to EU regulation 327/2011: Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
General notes Connection diagram: Accessories Compliant to standards
Page 144 Page 134 Page 6
Dimensions and fan ordering information Airflow direction - sucking
8
Type: R09R-3030HS-ES25C-01A04 Code: 0309-4-2003 Weight: 3.3kg
Type: R09P-3030HS-ES25C-01A04 Code: On request Weight:
120
Aerodynamic characteristic:
100
• measured in full bell mouth without guard grill • instalation category A according to ISO 5801
4
7 11
2
500
10 13
1000
9
5
1500
1
2000
2500
qv [m³/h]
U [V]
f [Hz]
n [RPM]
qv [m³/h]
psF [Pa]
Pe [W]
I [A]
LwA out [dB (A)]
Ta max [°C]
1
230
50
1650
2160
0
60
0.50
68
65
2
230
50
1650
1940
30
72
0.59
68
65
3
230
50
1650
1720
60
80
0.64
66
65
4
230
50
1650
1480
90
85
0.69
66
65
5
230
50
1400
1833
0
40
0.34
64
65
6
230
50
1400
1646
22
47
0.39
64
65
7
230
50
1400
1459
43
50
0.41
61
65
8
230
50
1400
1256
65
54
0.44
62
65
9
230
50
1150
1505
0
24
0.21
60
65
10
230
50
1150
1352
15
28
0.24
59
65
11
230
50
1150
1199
29
31
0.26
56
65
12
230
50
1150
1032
44
32
0.27
57
65
13
230
50
900
1178
0
14
0.13
54
65
14
230
50
900
1058
9
15
0.14
53
65
15
230
50
900
938
18
17
0.15
50
65
16
230
50
900
807
27
18
0.16
49
65
Airflow direction - blowing
Type: R09R-3030HB-ES25C-01A04 Code: On request Weight:
Definition of symbols U [V] f [Hz] n [RPM] qv [m³/h] psF [Pa] Pe [W] I [A] LwA [dB (A)] Ta max [ºC]
Supply voltage Frequency Fan speed Air flow Pressure drop Power input Current Sound power level A weighted Max. ambient temperature
AC axial fans Plastic blades
14
0
The values given may vary according to actual installation in the unit.
6
15
AC axial fans Paddle blades
20
AC radial fans backward curved blades
16
AC axial fans Sickled blades
12
40
• measured on pressure side 1m from fan mounted in full bell mouth without guard grill • measured according to ISO 3741
3
Type: R09P-3030HB-ES25C-01A04 Code: On request Weight:
Accessories
60
0
Sound power level:
8
Connection diagramS
psF [Pa]
80
EC axial fans
EC Axial fans
9
EC Axial fans
Diameter:
315 mm
R09_-3130H_-ES25C-01A04
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230V
Nominal voltage range
230 V
Frequency
50-60Hz
Input power
120 W
Input current
1.0 A
Nominal speed
1650 RPM
Min. ambient temperature
-25 째C
Protection class
IP44
Insulation class
130
ErP data according to EU regulation 327/2011: Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
General notes Connection diagram: Accessories Compliant to standards
Page 144 Page 134 Page 6
Dimensions and fan ordering information Airflow direction - sucking
10
Type: R09R-3130HS-ES25C-01A04 Code: 0309-4-2002 Weight: 3.3kg
Type: R09P-3130HS-ES25C-01A04 Code: On request Weight:
Aerodynamic characteristic: 120 100
• measured in full bell mouth without guard grill • instalation category A according to ISO 5801
4
80
7 11
2 10
1000
1500 qv [m³/h]
psF [Pa]
1
2000
Pe [W]
2500
I [A]
3000
U [V]
f [Hz]
n [RPM]
qv [m³/h]
LwA out [dB (A)]
Ta max [°C]
1
230
50
1650
2570
0
84
0.69
66
65
2
230
50
1650
2390
30
99
0.80
65
65
3
230
50
1650
2150
65
112
0.88
64
65
4
230
50
1650
1820
100
123
0.96
64
65
5
230
50
1400
2181
0
53
0.46
62
65
6
230
50
1400
2028
22
66
0.52
61
65
7
230
50
1400
1824
47
71
0.57
60
65
8
230
50
1400
1544
72
77
0.63
60
65
9
230
50
1150
1791
0
31
0.27
57
65
10
230
50
1150
1666
15
37
0.32
56
65
11
230
50
1150
1498
32
41
0.34
55
65
12
230
50
1150
1268
49
45
0.37
55
65
13
230
50
900
1402
0
18
0.16
51
65
14
230
50
900
1304
9
20
0.17
50
65
15
230
50
900
1173
19
23
0.20
49
65
16
230
50
900
993
30
24
0.20
49
65
Airflow direction - blowing
Type: R09R-3130HB-ES25C-01A04 Code: On request Weight:
Definition of symbols U [V] f [Hz] n [RPM] qv [m³/h] psF [Pa] Pe [W] I [A] LwA [dB (A)] Ta max [ºC]
Supply voltage Frequency Fan speed Air flow Pressure drop Power input Current Sound power level A weighted Max. ambient temperature
AC axial fans Plastic blades
500
5
9
AC axial fans Paddle blades
14 13
0
The values given may vary according to actual installation in the unit.
6
AC radial fans backward curved blades
15
Type: R09P-3130HB-ES25C-01A04 Code: On request Weight:
Accessories
20
Connection diagramS
psF [Pa]
12
40
0
• measured on pressure side 1m from fan mounted in full bell mouth without guard grill • measured according to ISO 3741
3
60
AC axial fans Sickled blades
Sound power level:
8
16
EC axial fans
EC Axial fans
11
EC Axial fans
Diameter:
330 mm
R09_-3330H_-ES25C-01A06
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Nominal voltage range
230 V
Frequency
50-60 Hz
Input power
120 W
Input current
0.90 A
Nominal speed
1550 RPM
Min. ambient temperature
-25 째C
Protection class
IP44
Insulation class
130
ErP data according to EU regulation 327/2010: Overall efficiency Measurement category Compliant to
Efficiency category Efficiency grade N Variable speed drive Power input Air flow Pressure drop Rotational speed Specific ratio
General notes Connection diagram: Accessories Compliant to standards
46.4 % A static 58.2 INTEGRATED 136 W 1854 m3/h 111 Pa 1556 RPM 1.00
Page 144 Page 134 Page 6
Dimensions and fan ordering information Airflow direction - sucking
12
Type: R09R-3330HS-ES25C-01A06 Code: 0309-4-2001 Weight: 3.5kg
Airflow direction - sucking
Type: R09P-3330HS-ES25C-01A06 Code: On request Weight:
120
Aerodynamic characteristic:
100
• measured in full bell mouth without guard grill • instalation category A according to ISO 5801
4
80
7
40 11
2 6
1500 qv [m³/h]
psF [Pa]
2000
Pe [W]
1
2500
I [A]
3000
U [V]
f [Hz]
n [RPM]
qv [m³/h]
LwA out [dB (A)]
Ta max [°C]
1
230
50
1550
2800
0
83
0.68
70
65
2
230
50
1550
2610
30
98
0.80
68
65
3
230
50
1550
2355
60
116
0.94
66
65
4
230
50
1550
2050
90
123
0.99
66
65
5
230
50
1350
2439
0
53
0.49
66
65
6
230
50
1350
2273
23
68
0.56
64
65
7
230
50
1350
2051
46
76
0.64
63
65
8
230
50
1350
1785
68
81
0.66
62
65
9
230
50
1150
2077
0
38
0.32
62
65
10
230
50
1150
1936
17
44
0.37
60
65
11
230
50
1150
1747
33
47
0.41
59
65
12
230
50
1150
1521
50
53
0.43
58
65
13
230
50
950
1716
0
21
0.19
57
65
14
230
50
950
1600
11
26
0.23
55
65
15
230
50
950
1443
23
28
0.24
54
65
16
230
50
950
1256
34
32
0.27
53
65
Airflow direction - blowing
Type: R09R-3330HB-ES25C-01A06 Code: On request Weight:
Definition of symbols U [V] f [Hz] n [RPM] qv [m³/h] psF [Pa] Pe [W] I [A] LwA [dB (A)] Ta max [ºC]
Supply voltage Frequency Fan speed Air flow Pressure drop Power input Current Sound power level A weighted Max. ambient temperature
AC axial fans Plastic blades
1000
5
AC axial fans Paddle blades
500
9
AC radial fans backward curved blades
13
0
The values given may vary according to actual installation in the unit.
10
14
Type: R09P-3330HB-ES25C-01A06 Code: On request Weight:
Accessories
15
20
Connection diagramS
psF [Pa]
12
0
• measured on pressure side 1m from fan mounted in full bell mouth without guard grill • measured according to ISO 3741
3
AC axial fans Sickled blades
Sound power level:
8
60
16
EC axial fans
EC Axial fans
13
EC Axial fans
Diameter:
350 mm
R09_-3530H_-ES25C-01A01
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Nominal voltage range
230 V
Frequency
50-60 Hz
Input power
125 W
Input current
0.98 A
Nominal speed
1400 RPM
Min. ambient temperature
-25 째C
Protection class
IP44
Insulation class
130
ErP data according to EU regulation 327/2010: Overall efficiency Measurement category Compliant to
Efficiency category Efficiency grade N Variable speed drive Power input Air flow Pressure drop Rotational speed Specific ratio
General notes Connection diagram: Accessories Compliant to standards
46.7 % A static 58.7 INTEGRATED 127 W 1860 m3/h 103 Pa 1393 RPM 1.00
Page 144 Page 134 Page 6
Dimensions and fan ordering information Airflow direction - sucking
14
Type: R09R-3530HS-ES25C-01A01 Code: 0309-4-2000 Weight: 3.6 kg
Airflow direction - sucking
Type: R09P-3530HS-ES25C-01A01 Code: On request Weight:
120
Aerodynamic characteristic:
100
• measured in full bell mouth without guard grill • instalation category A according to ISO 5801
4
80
12
• measured on pressure side 1m from fan mounted in full bell mouth without guard grill • measured according to ISO 3741
7
40 11
16
2
1000
1500 qv [m³/h]
U [V]
f [Hz]
n [RPM]
qv [m³/h]
1
230
50
1400
2890
2
230
50
1400
2650
3
230
50
1400
2220
4
230
50
1400
5
230
50
1200
psF [Pa]
9
1
5
2000
2500
3000
Pe [W]
I [A]
LwA out [dB (A)]
Ta max [°C]
0
84
0.66
70
65
30
103
0.79
67
65
65
109
0.88
65
65
1830
100
132
1.02
67
55
2477
0
56
0.45
66
65
6
230
50
1200
2271
22
67
0.53
63
65
7
230
50
1200
1903
48
76
0.60
62
65
8
230
50
1200
1569
73
88
0.68
63
65
9
230
50
1000
2064
0
35
0.28
62
65
10
230
50
1000
1893
15
40
0.35
58
65
11
230
50
1000
1586
33
44
0.37
56
65
12
230
50
1000
1307
51
52
0.42
58
65
13
230
50
800
1651
0
20
0.16
55
65
14
230
50
800
1514
10
23
0.19
52
65
15
230
50
800
1269
21
24
0.22
50
65
16
230
50
800
1046
33
29
0.24
52
65
Airflow direction - blowing
Type: R09R-3530HB-ES25C-01A01 Code: 0309-4-2021 Weight: 3.6 kg
Definition of symbols U [V] f [Hz] n [RPM] qv [m³/h] psF [Pa] Pe [W] I [A] LwA [dB (A)] Ta max [ºC]
Airflow direction - blowing
Supply voltage Frequency Fan speed Air flow Pressure drop Power input Current Sound power level A weighted Max. ambient temperature
AC axial fans Plastic blades
500
13
AC axial fans Paddle blades
0
10
AC radial fans backward curved blades
14
0
The values given may vary according to actual installation in the unit.
6
Type: R09P-3530HB-ES25C-01A01 Code: On request Weight:
Accessories
15
20
AC axial fans Sickled blades
Sound power level:
3
60
Connection diagramS
psF [Pa]
8
EC axial fans
EC Axial fans
15
EC Axial fans
Diameter:
400 mm
R10_-40AP_-ES50B-02A01
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Nominal voltage range
200-240 V
Frequency
50-60 Hz
Input power
320 W
Input current
2.15 A
Nominal speed
1520 RPM
Min. ambient temperature
-25 째C
Protection class
IP54
Insulation class
130
ErP data according to EU regulation 327/2010: Overall efficiency Measurement category Compliant to
Efficiency category Efficiency grade N Variable speed drive Power input Air flow Pressure drop Rotational speed Specific ratio
General notes Connection diagram: Accessories Compliant to standards
43.1 % A static 52.4 INTEGRATED 342 W 3069 m3/h 161 Pa 1504 RPM 1.00
Page 144 Page 134 Page 6
Dimensions and fan ordering information Airflow direction - sucking
16
Type: R10R-40APS-ES50B-02A01 Code: 0310-4-0000 Weight: 5.0 kg
Airflow direction - sucking
Type: R10P-40APS-ES50B-02A01 Code: 0310-4-0025 Weight: 7.5 kg
Aerodynamic characteristic:
180
• measured in full bell mouth without guard grill • instalation category A according to ISO 5801
160 4
120
6
13
0
1000
2000
3000 qv [m³/h]
U [V]
f [Hz]
n [RPM]
qv [m³/h]
1
230
50
1520
2
230
50
1520
3
230
50
4
230
5
230
6 7
The values given may vary according to actual installation in the unit.
10
14
9
5
4000
psF [Pa]
Pe [W]
5200
0
4770
50
1520
4150
50
1520
50
1300
230
50
230
50
8
230
1
5000
6000
I [A]
LwA out [dB (A)]
Ta max [°C]
289
1.91
74
65
316
2.05
72
65
100
323
2.10
69
65
3400
140
325
2.13
70
65
4447
0
181
1.21
70
65
1300
4080
37
201
1.33
68
65
1300
3549
73
211
1.40
65
65
50
1300
2908
102
213
1.42
65
65
9
230
50
1100
3763
0
113
0.79
66
65
10
230
50
1100
3452
26
126
0.87
64
65
11
230
50
1100
3003
52
130
0.90
61
65
12
230
50
1100
2461
73
135
0.93
60
65
13
230
50
900
3079
0
68
0.49
60
65
14
230
50
900
2824
18
71
0.52
59
65
15
230
50
900
2457
35
76
0.55
56
65
16
230
50
900
2013
49
75
0.54
55
65
Airflow direction - blowing
Type: R10R-40APB-ES50B-02A01 Code: 0310-4-0026 Weight: 5.0 kg
AC axial fans Sickled blades
2
15
20 0
11
16
Definition of symbols U [V] f [Hz] n [RPM] qv [m³/h] psF [Pa] Pe [W] I [A] LwA [dB (A)] Ta max [ºC]
Airflow direction - blowing
Supply voltage Frequency Fan speed Air flow Pressure drop Power input Current Sound power level A weighted Max. ambient temperature
AC axial fans Plastic blades
60 40
• measured on pressure side 1m from fan mounted in full bell mouth without guard grill • measured according to ISO 3741
7
AC axial fans Paddle blades
12
AC radial fans backward curved blades
psF [Pa]
80
Sound power level:
3
Type: R10P-40APB-ES50B-02A01 Code: 0310-4-0027 Weight: 7.5 kg
Accessories
8
100
Connection diagramS
140
EC axial fans
EC Axial fans
17
EC Axial fans
Diameter:
450 mm
R10_-45AP_-ES50B-04A05
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Nominal voltage range
200-240 V
Frequency
50-60 Hz
Input power
300 W
Input current
2.05 A
Nominal speed
1280 RPM
Min. ambient temperature
-25 째C
Protection class
IP54
Insulation class
130
ErP data according to EU regulation 327/2010: Overall efficiency Measurement category Compliant to
Efficiency category Efficiency grade N Variable speed drive Power input Air flow Pressure drop Rotational speed Specific ratio
General notes Connection diagram: Accessories Compliant to standards
43.2 % A static 52.5 INTEGRATED 345 W 3966 m3/h 127 Pa 1287 RPM 1.00
Page 144 Page 134 Page 6
Dimensions and fan ordering information Airflow direction - sucking
18
Type: R10R-45APS-ES50B-04A05 Code: 0310-4-0018 Weight: 5.3 kg
Airflow direction - sucking
Type: R10P-45APS-ES50B-04A05 Code: 0310-4-0028 Weight: 7.8 kg
150
Aerodynamic characteristic:
125
• measured in full bell mouth without guard grill • instalation category A according to ISO 5801
4
100
12
• measured on pressure side 1m from fan mounted in full bell mouth without guard grill • measured according to ISO 3741
7
50 11
1000
2000
3000
U [V]
f [Hz]
n [RPM]
qv [m³/h]
1
230
50
1280
2
230
50
1280
3
230
50
4
230
5
230
6 7
13
5
9
4000 qv [m³/h]
5000
1
6000
7000
psF [Pa]
Pe [W]
I [A]
LwA out [dB (A)]
Ta max [°C]
6210
0
251
1.67
69
60
5670
40
287
1.88
68
60
1280
4930
80
303
2.00
67
60
50
1280
3890
120
321
2.07
68
60
50
1100
5337
0
163
1.10
65
60
230
50
1100
4873
30
183
1.22
63
60
230
50
1100
4237
59
200
1.32
63
60
8
230
50
1100
3343
89
209
1.38
64
60
9
230
50
900
4366
0
92.4
0.66
60
60
10
230
50
900
3987
20
103
0.73
59
60
11
230
50
900
3466
40
113
0.79
58
60
12
230
50
900
2735
59
115
0.81
59
60
13
230
50
700
3396
0
47
0.37
54
60
14
230
50
700
3101
12
52
0.40
53
60
15
230
50
700
2696
24
56
0.43
52
60
16
230
50
700
2127
36
57
0.43
52
60
Airflow direction - blowing
Type: R10R-45APB-ES50B-04A05 Code: 0310-4-0029 Weight: 5.3 kg
Definition of symbols U [V] f [Hz] n [RPM] qv [m³/h] psF [Pa] Pe [W] I [A] LwA [dB (A)] Ta max [ºC]
Airflow direction - blowing
Supply voltage Frequency Fan speed Air flow Pressure drop Power input Current Sound power level A weighted Max. ambient temperature
AC axial fans Plastic blades
0
The values given may vary according to actual installation in the unit.
10
AC axial fans Paddle blades
15 14
0
2 6
AC radial fans backward curved blades
25
Type: R10P-45APB-ES50B-04A05 Code: 0310-4-0030 Weight: 7.8 kg
Accessories
16
Connection diagramS
psF [Pa]
3
AC axial fans Sickled blades
Sound power level:
8
75
EC axial fans
EC Axial fans
19
EC Axial fans
Diameter:
500 mm
R10_-50LP_-ES50B-04A05
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Nominal voltage range
200-240 V
Frequency
50-60 Hz
Input power
300 W
Input current
2.05 A
Nominal speed
1280 RPM
Min. ambient temperature
-25 째C
Protection class
IP54
Insulation class
130
ErP data according to EU regulation 327/2010: Overall efficiency Measurement category Compliant to
Efficiency category Efficiency grade N Variable speed drive Power input Air flow Pressure drop Rotational speed Specific ratio
General notes Connection diagram: Accessories Compliant to standards
49.4 % A static 58.7 INTEGRATED 340 W 4750 m3/h 121 Pa 1278 RPM 1.00
Page 144 Page 134 Page 6
Dimensions and fan ordering information Airflow direction - sucking
20
Type: R10R-50LPS-ES50B-04A05 Code: 0310-4-0022 Weight: 5.8 kg
Airflow direction - sucking
Type: R10P-50LPS-ES50B-04A05 Code: 0310-4-0009 Weight: 11.3 kg
Aerodynamic characteristic:
140
• measured in full bell mouth without guard grill • instalation category A according to ISO 5801
120 4
100
11
2
3000
U [V]
f [Hz]
n [RPM]
qv [m³/h]
1
230
50
1280
2
230
50
1280
3
230
50
4
230
5
230
6 7
4000 qv [m³/h]
1
5
5000
6000
7000
psF [Pa]
Pe [W]
I [A]
LwA out [dB (A)]
Ta max [°C]
6330
0
206
1.39
70
65
5910
35
245
1.64
70
65
1280
5330
75
296
1.97
70
65
50
1280
4580
110
326
2.16
73
65
50
1100
5440
0
135
0.94
66
65
230
50
1100
5100
26
165
1.13
67
65
230
50
1100
4570
55
195
1.33
66
65
8
230
50
1100
3940
81
212
1.42
69
65
9
230
50
900
4450
0
81
0.59
61
65
10
230
50
900
4160
17
92
0.66
61
65
11
230
50
900
3750
37
110
0.78
60
65
12
230
50
900
3220
54
122
0.85
63
65
13
230
50
700
3470
0
43
0.34
55
65
14
230
50
700
3230
10
49
0.38
54
65
15
230
50
700
2910
22
56
0.42
54
65
16
230
50
700
2500
33
64
0.47
57
65
Airflow direction - blowing
Type: R10R-50LPB-ES50B-04A05 Code: 0310-4-0023 Weight: 5.8 kg
Definition of symbols U [V] f [Hz] n [RPM] qv [m³/h] psF [Pa] Pe [W] I [A] LwA [dB (A)] Ta max [ºC]
Airflow direction - blowing
Supply voltage Frequency Fan speed Air flow Pressure drop Power input Current Sound power level A weighted Max. ambient temperature
AC axial fans Plastic blades
2000
9
AC axial fans Paddle blades
1000
10
AC radial fans backward curved blades
14 13
0
The values given may vary according to actual installation in the unit.
6
15
Type: R10P-50LPB-ES50B-04A05 Code: 0310-4-0024 Weight: 11.3 kg
Accessories
16
20 0
7
12
40
• measured on pressure side 1m from fan mounted in full bell mouth without guard grill • measured according to ISO 3741
Connection diagramS
psF [Pa]
60
Sound power level:
3
AC axial fans Sickled blades
8
80
EC axial fans
EC Axial fans
21
EC Axial fans
Diameter:
560 mm
R10_-56LP_-ES50B-04A10
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Nominal voltage range
200-240 V
Frequency
50-60 Hz
Input power
240 W
Input current
1.68 A
Nominal speed
950 RPM
Min. ambient temperature
-25 째C
Protection class
IP54
Insulation class
130
ErP data according to EU regulation 327/2010: Overall efficiency Measurement category Compliant to
Efficiency category Efficiency grade N Variable speed drive Power input Air flow Pressure drop Rotational speed Specific ratio
General notes Connection diagram: Accessories Compliant to standards
45.0 % A static 54.9 INTEGRATED 280 W 5269 m3/h 80 Pa 953 RPM 1.00
Page 144 Page 134 Page 6
Dimensions and fan ordering information Airflow direction - sucking
22
Type: R10R-56LPS-ES50B-04A10 Code: 0310-4-0031 Weight: 6.0 kg
Airflow direction - sucking
Type: R10P-56LPS-ES50B-04A10 Code: 0310-4-0020 Weight: 13.7 kg
120
Aerodynamic characteristic:
100
• measured in full bell mouth without guard grill • instalation category A according to ISO 5801
4
11
U [V]
f [Hz]
n [RPM]
qv [m³/h]
1
230
50
950
2
230
50
950
3
230
50
4
230
5
230
6 7
4000 qv [m³/h]
5000
6000
1
7000
8000
psF [Pa]
Pe [W]
I [A]
LwA out [dB (A)]
Ta max [°C]
7560
0
188
1.28
70
65
6840
30
219
1.48
69
65
950
5900
60
251
1.68
66
65
50
950
4500
90
272
1.82
66
65
50
800
6366
0
113
0.80
66
65
230
50
800
5760
21
134
0.93
65
65
230
50
800
4968
43
151
1.04
62
65
8
230
50
800
3789
64
162
1.11
62
65
9
230
50
650
5173
0
62
0.47
61
65
10
230
50
650
4680
14
74
0.54
60
65
11
230
50
650
4037
28
82
0.60
57
65
12
230
50
650
3079
42
88
0.64
56
65
13
230
50
500
3979
0
31
0.26
54
65
14
230
50
500
3600
8
36
0.29
53
65
15
230
50
500
3105
17
41
0.32
51
65
16
230
50
500
2368
25
44
0.35
49
65
Airflow direction - blowing
Type: R10R-56LPB-ES50B-04A10 Code: 0310-4-0032 Weight: 6.0 kg
Definition of symbols U [V] f [Hz] n [RPM] qv [m³/h] psF [Pa] Pe [W] I [A] LwA [dB (A)] Ta max [ºC]
Airflow direction - blowing
Supply voltage Frequency Fan speed Air flow Pressure drop Power input Current Sound power level A weighted Max. ambient temperature
AC axial fans Plastic blades
3000
5
AC axial fans Paddle blades
2000
9
13
AC radial fans backward curved blades
14
1000
The values given may vary according to actual installation in the unit.
10
Type: R10P-56LPB-ES50B-04A10 Code: 0310-4-0033 Weight: 13.7 kg
Accessories
15
0
2 6
AC axial fans Sickled blades
7
16
20
• measured on pressure side 1m from fan mounted in full bell mouth without guard grill • measured according to ISO 3741
3
12
40
0
Sound power level:
8
60
Connection diagramS
psF [Pa]
80
EC axial fans
EC Axial fans
23
EC Axial fans
Diameter:
630 mm
R10_-63LP_-ES50B-03A11
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Nominal voltage range
200-240 V
Frequency
50-60 Hz
Input power
250 W
Input current
1.65 A
Nominal speed
770 RPM
Min. ambient temperature
-25 째C
Protection class
IP54
Insulation class
130
ErP data according to EU regulation 327/2010: Overall efficiency Measurement category Compliant to
Efficiency category Efficiency grade N Variable speed drive Power input Air flow Pressure drop Rotational speed Specific ratio
General notes Connection diagram: Accessories Compliant to standards
40.4 % A static 50.3 INTEGRATED 270 W 5787 m3/h 62 Pa 760 RPM 1.00
Page 144 Page 134 Page 6
Dimensions and fan ordering information Airflow direction - sucking
24
Type: R10R-63LPS-ES50B-03A11 Code: 0310-4-0013 Weight: 6.4 kg
Airflow direction - sucking
Type: R10P-63LPS-ES50B-03A11 Code: 0310-4-0010 Weight: 15.2 kg
Aerodynamic characteristic:
100
4
11
2 6
0
13
0
2000
4000
U [V]
f [Hz]
n [RPM]
qv [m³/h]
1
230
50
770
2
230
50
770
3
230
50
4
230
5
230
6 7
The values given may vary according to actual installation in the unit.
10
14
9
6000 qv [m³/h]
5
1
8000
10000
psF [Pa]
Pe [W]
I [A]
LwA out [dB (A)]
Ta max [°C]
8930
0
201
1.36
67
65
7850
30
240
1.61
65
65
770
6350
55
266
1.78
64
50
50
770
4400
80
274
1.82
71
65
50
650
7530
0
115
0.81
62
65
230
50
650
6640
21
136
0.95
60
65
230
50
650
5370
39
155
1.06
60
65
8
230
50
650
3730
57
146
1.02
67
65
9
230
50
550
6350
0
71
0.53
57
65
10
230
50
550
5600
15
82
0.60
56
65
11
230
50
550
4550
28
94
0.68
56
65
12
230
50
550
3170
41
89
0.65
62
65
13
230
50
450
5200
0
40
0.31
51
65
14
230
50
450
4590
10
46
0.35
51
65
15
230
50
450
3700
19
52
0.40
51
65
16
230
50
450
2600
27
50
0.39
57
65
Airflow direction - blowing
Type: R10R-63LPB-ES50B-03A11 Code: 0310-4-0034 Weight: 6.4 kg
Definition of symbols U [V] f [Hz] n [RPM] qv [m³/h] psF [Pa] Pe [W] I [A] LwA [dB (A)] Ta max [ºC]
Airflow direction - blowing
Supply voltage Frequency Fan speed Air flow Pressure drop Power input Current Sound power level A weighted Max. ambient temperature
AC axial fans Plastic blades
15
AC axial fans Sickled blades
7
16
20
• measured on pressure side 1m from fan mounted in full bell mouth without guard grill • measured according to ISO 3741
AC axial fans Paddle blades
12
40
Sound power level:
3
AC radial fans backward curved blades
psF [Pa]
8
Type: R10P-63LPB-ES50B-03A11 Code: 0310-4-0035 Weight: 15.2 kg
Accessories
60
Connection diagramS
80
• measured in full bell mouth without guard grill • instalation category A according to ISO 5801
EC axial fans
EC Axial fans
25
02 AC Axial fans Sickled blades
26
AC axial fans Plastic blades
AC axial fans Sickled blades
EC axial fans
AC Axial fans Sickled blades
AC radial fans backward curved blades
AC axial fans Paddle blades
AC Axial fans Sickled blades
Connection diagram
Accessories
XXX Arciis erchic temolor empeles nam, quo tectorehenem fuga. Nam as simagniscia aut repelist quam sa que occae. Nemporionse volum none sam, sequae natur sus etur, nihil ipis aut es seque nations ecescit voluptatent ma nos aut ex et volorepedis et aut ut lamus et porem escit, earum.
27
AC Axial fans Sickled blades
AC axial & radial fans ■■ Electrical connection and motor
and maintenance instructions of used VSD when applied to Hidria fans.
AC Axial and radial fans are driven by single phase or three-phase AC (Alternating Current) external rotor induction motors. The motors are integrated into the fan hub.
■■ Installation and usage information
The rated voltage for a three-phase power supply is 400 V and for single-phase AC motors it is 230 V. The single phase or three-phase AC motors are suitable for 400 V ±10 % or 230 V ± 10 %, as well as 50/60 Hz. All other voltage types are available as customized solutions.
■■ Motor connection Mains connection is made via terminal box or outgoing connection cable as shown in dimensional drawings.
■■ Terminal box and connection cable Terminal boxes are made of shock-proof and weather-resistant plastics. Heat and UV resistant halogen-free hose cables are used, marked by a color code or connection designations as labeled on to terminal block. The cable construction complies with VDE 0282 Part 804 and is suitable for operating voltages of up to 400 V for single phase products and 690 V for tri phase products.
■■ Speed controls Hidria AC fans are suitable for operation with or without one of the Variable Speed Drive (VSD) units such as frequency converter, triac controller, soft start or autotransformer. When VSD is in use, special caution need to be taken to verify that temperature rise is in line with motor insulation class (B or H) limits and that EMC requirements of final appliance are meet. It is recommended to use Sine Wave Filter attached between frequency converter and AC fan in order to assure the best acoustic and lifetime performance of the fan. Please follow the safety, installation
28
For the installation, maintenance and safe usage of AC axial fans, please refer to user manual.
lower of the condensation drain hole must be open when the fan is installed with the rotor at the bottom. With horizontal mounting position condensate can escape via the gap between stator and rotor. Installation with rotor at the top (connection box or cables at the bottom) is available only on request.
Operating mode Continuous operation (S1).
■■ Materials and corrosion protection Hidria AC Axial fan impellers are made of high-performance PA composite material, aluminum or steel. The impeller is pressed onto the rotor. Some axial fans have stamped steel or aluminum panel blades. This type of blades are riveted or screwed onto the rotors of the external rotor motor. The rotor and stator flange are made of hi-pressure die-casted seawater resistant aluminum alloys. The fan nozzles are made of steel sheet and coated to meet resistance to corrosion as set by ISO 12944-2 class C3 (medium). Additional coating on request and at supplementary cost. The wire protection grills have a weather resistant plastic coating.
■■ Operating conditions and product life Safety The fans may only be operated when they are installed as intended and when safety is ensured by safety equipment according to DIN EN 294 resp. ISO13852 (DIN EN ISO 12100) or by other protection measures.
Safety approvals Depending on the product, Hidria fans comply with the one or more of the following standards: EN 60335-1, EN 61800-5-1 and EN 60034-1. The majority of the fans can be supplied in CE, UL/CSA, CCC and/or GOST approved design.
Condensation drain holes Axial and radial fans are intended to be installed with rotor in horizontal position or with rotor at the bottom of the fan (connection box or cables on the top). The
Resistance to water, dust and moisture Majority of axial fans are resistant to presence of water, dust and moisture as defined by class IP44 or IP 54 (IEC 60529, IEC60034, IEC60335).
Ambient conditions If not instructed differently the fans can be subjected to the following conditions: • Placed outdoors (rain, snow, UV radiation). • Working ambient temperatures between -30°C and +70°C. • Storage temperatures -40°C to +80°C.
Product life By utilizing lifetime maintenance free bearings, our axial fans are maintenance free for the entire life time of approximately 30-40.000 hours for standard applications and environmental conditions. Contact protection The preferred “protective construction” used on axial fans is a guard grille. Depending on the airflow direction, the guard grille is located on the intake or pressure side of the fan. The “Accessories” section contains separate guard grilles, which can be positioned on the pressure or intake side of the fan as required and depending on the installation situation, to meet the safety requirements set out in DIN EN ISO 13857, defining safety distance requirements to prevent upper limbs from getting into hazardous areas. The guard grille results in a resistance to the conveyed airflow, which manifests itself in the pressure loss.
AC Axial fans Sickled blades
AC axial fans Sickled blades
EC axial fans
Axial fans with induction (AC) motors and sickled blades Stamped steel blades (type 18H, 30H)
AC axial fans Plastic blades
Diameters: 300-350 mm
Stamped aluminium blades (type 30H)
AC axial fans Paddle blades
Diameters: 450-630 mm
Die-cast aluminium blades (30H)
AC radial fans backward curved blades
Diameters: 630-800 mm
Example of type key:
R13R-5630HA-6T2-7008 R13 External rotor motor type (R09, R13)
Accessories
R Acessory type (E ‒ without guard grill, R ‒ with guard grill, P ‒ with guard grill and wall plate) 56 Fan diameter x 10 (exact diameters are stated in drawings) 30H Type of blabes (18H, 30H) A Airflow direction (A ‒ sucking, P ‒ blowing)
Connection diagram
6 Number of motor poles T Number of phases (M ‒ single phase, T ‒ three phase) 2 Number of motor speed 70 Motor steck height 08 Version of electrical construction
29
AC Axial fans Sickled blades
300 mm
Diameter:
R09_-3018H_-2M-4248
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
140/190 W
Rated current
0.62/0.83 A
Rated speed
2590/2700 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
55/40 °C
Sound power level A weighted
83/87 dB (A)
Condensator
5 μF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
Compliant to
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Sucking Blowing
Overall efficiency
Type
Code
R09R-3018HA-2M-4248 R09R-3018HP-2M-4248
0309-4-1093 0309-4-1094
Weight (kg)
3.5
29.0 %
Measurement category
A
Efficiency category
static
Efficiency grade N
40.2
Variable speed drive
NO
Power input
169 W
Air flow 61
1553 m³/h
Pressure drop
44 3
118 Pa
Speed
2585 RPM
Specific ratio
1.00
6,5
300 316 360 376
Aerodynamic characteristic 50Hz
60Hz
ErP Data
150 125
psF [Pa]
100
155
75 50 25
Fan with plate Airflow Direction
Type
Sucking
R09P-3018HA-2M-4248
On request
Blowing
R09P-3018HP-2M-4248
On request
Code
Weight (kg)
Type
Code
Sucking
R09E-3018HA-2M-4248
On request
Blowing
R09E-3018HP-2M-4248
On request
30
0
500
1000
1500
2000
2500
3000
3500
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
Fan without guard grill Airflow Direction
0
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0043 0301-1-0044
Page 145 Page 134 Page 28
R09_-3030H_-4M-2543
300 mm
Diameter:
EC axial fans
AC Axial fans Sickled blades
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V 50/60 Hz
Rated power input
AC axial fans Sickled blades
Frequency
65/90 W
Rated current
0.30/0.40 A
Rated speed
1400/1500 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70 °C 66/71 dB (A)
Condensator
2 μF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Aerodynamic characteristic 50Hz
60Hz
Type
Code
Sucking R09R-3030HA-4M-2543
0309-4-1112
Blowing
0309-4-1050
R09R-3030HP-4M-2543
Weight (kg) AC axial fans Paddle blades
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
3.0
75 61
31
AC radial fans backward curved blades
45 30
0
300 316 360 376
15
0
500
1000
1500 qv [m³/h]
2000
6,5
psF [Pa]
60
2500
Fan characteristic measured in full bell mouth with guard grill Accessories
142
Fan with plate Type
Code
Sucking
R09P-3030HA-4M-2543
0309-4-1025
Blowing
R09P-3030HP-4M-2543
0309-4-1078
Weight (kg)
4.5
Connection diagram
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Fan without guard grill 0301-1-0043 0301-1-0044
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R09E-3030HA-4M-2543
On request
Blowing
R09E-3030HP-4M-2543
On request
Weight (kg)
31
AC Axial fans Sickled blades
300 mm
Diameter:
R09_-3030H_-4T-2545
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400/230 V
Frequency
50/60 Hz
Rated power input
75/80 W
Rated current
0.20/0.35/0.17/0.30 A
Rated speed
1370/1550 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
55 °C
Sound power level A weighted
67/72 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011: Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Fan with guard grill Airflow Direction
Type
Code
Sucking
R09R-3030HA-4T-2545
0309-4-1038
Blowing
R09R-3030HP-4T-2545
On request
Weight (kg)
Aerodynamic characteristic
3.0
50Hz
60Hz
75 60
31
psF [Pa]
61
45 30
6,5
300 316 360 376
15 0
0
500
1000 1500 qv [m³/h]
2000
2500
Fan characteristic measured in full bell mouth with guard grill
142
Fan with plate Airflow Direction
Type
Code
Sucking
R09P-3030HA-4T-2545
On request
Blowing
R09P-3030HP-4T-2545
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R09E-3030HA-4T-2545
On request
Blowing
R09E-3030HP-4T-2545
On request
32
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0049 0301-1-0049
Page 146 Page 134 Page 28
R09_-3130H_-4M-3509
315 mm
Diameter:
EC axial fans
AC Axial fans Sickled blades
Nominal data according to standard EN 60335: Phase
1~ 230 V
Frequency
50/60 Hz
Rated power input
90/120 W
Rated current
0.40/0.55 A
Rated speed
1350/1500 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70/60 °C 68/72 dB (A)
Condensator
3 μF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
AC axial fans Sickled blades
Nominal voltage
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Aerodynamic characteristic 50Hz
60Hz
Type
Code
Sucking
R09R-3130HA-4M-3509
0309-4-1002
Blowing
R09R-3130HP-4M-3509
On request
Weight (kg) AC axial fans Paddle blades
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
3.3
75 75
29
AC radial fans backward curved blades
45 30
0
312 356 400 416
15
0
500
1000
1500
2000
2500
6,5
psF [Pa]
60
3000
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill
Accessories
155
Fan with plate Type
Code
Sucking
R09P-3130HA-4M-3509
0309-4-1015
Blowing
R09P-3130HP-4M-3509
On request
Weight (kg)
4.5
Connection diagram
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Fan without guard grill 0301-1-0043 0301-1-0044
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R09E-3130HA-4M-3509
On request
Blowing
R09E-3130HP-4M-3509
On request
Weight (kg)
33
AC Axial fans Sickled blades
315 mm
Diameter:
R09_-3130H_-4T-3524
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400/230 V
Frequency
50/60 Hz
Rated power input
100/120 W
Rated current
0.23/0.41/0.22/0.39 A
Rated speed
1340/1490 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
55 °C
Sound power level A weighted
69/73 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011: Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Fan with guard grill Airflow Direction
Type
Code
Sucking
R09R-3130HA-4T-3524
0309-4-1039
Blowing
R09R-3130HP-4T-3524
On request
Weight (kg)
Aerodynamic characteristic
3.4
50Hz
60Hz
75 60
29
psF [Pa]
75
45 30
6,5
312 356 400 416
15 0
0
500
1000
1500
2000
2500
3000
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill
155
Fan with plate Airflow Direction
Type
Code
Sucking
R09P-3130HA-4T-3524
On request
Blowing
R09P-3130HP-4T-3524
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R09E-3130HA-4T-3524
On request
Blowing
R09E-3130HP-4T-3524
On request
34
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0049 0301-1-0049
Page 146 Page 134 Page 28
R09_-3330H_-4M-3542
330 mm
Diameter:
EC axial fans
AC Axial fans Sickled blades
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V 50/60 Hz
Rated power input
130/170 W
Rated current
0.55/0.75 A
Rated speed
1350/1500 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
55 °C 70/74 dB (A)
Condensator
4 μF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
AC axial fans Sickled blades
Frequency
ErP data according to EU regulation 327/2011:
Fan with guard grill
25.9 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
37.8
Sucking R09R-3330HA-4M-3542
Variable speed drive
NO
Blowing
Power input
133 W
Air flow
Type
Code
R09R-3330HP-4M-3542
0309-4-1001 On request
Weight (kg) AC axial fans Paddle blades
Overall efficiency
3.4
1800 m³/h
Pressure drop
72 Pa
Speed
75
33
1350 RPM 1.00
AC radial fans backward curved blades
Specific ratio
60Hz
ErP Data
330 356 400 416
50Hz
6,5
Aerodynamic characteristic 90 75
45
158
Accessories
psF [Pa]
60
30 15 0
500
1000
1500
2000
2500
3000
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R09P-3330HA-4M-3542
On request
Blowing
R09P-3330HP-4M-3542
On request
Weight (kg)
Connection diagram
0
Fan with plate
Fan without guard grill 0301-1-0043 0301-1-0044
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R09E-3330HA-4M-3542
On request
Blowing
R09E-3330HP-4M-3542
On request
Weight (kg)
35
AC Axial fans Sickled blades
350 mm
Diameter:
R09_-3530H_-4M-4237
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
130/165 W
Rated current
0.60/0.72 A
Rated speed
1290/1380 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
60 °C
Sound power level A weighted
72/75 dB (A)
Condensator
4 μF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
Compliant to
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Sucking Blowing
Overall efficiency
Type
Code
R09R-3530HA-4M-4237 R09R-3530HP-4M-4237
0309-4-1000 0309-4-1032
Weight (kg)
3.7
29.0 %
Measurement category
A
Efficiency category
static
Efficiency grade N
40.7
Variable speed drive
NO
Power input
140 W
Air flow 84
1975 m³/h
Pressure drop
29
79 Pa
Speed
1333 RPM
Specific ratio
1.00
6,5
350 376 442 460
Aerodynamic characteristic 50Hz
60Hz
ErP Data
2000
3000
90 75
psF [Pa]
60 162
45 30 15
Fan with plate Airflow Direction
Type
Code
Sucking
R09P-3530HA-4M-4237
0309-4-1013
Blowing
R09P-3530HP-4M-4237
0309-4-1122
Weight (kg)
6.2
Fan without guard grill Airflow Direction
Type
Code
Sucking
R09E-3530HA-4M-4237
On request
Blowing
R09E-3530HP-4M-4237
On request
36
Weight (kg)
0
0
1000
4000
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0043 0301-1-0044
Page 145 Page 134 Page 28
R09_-3530H_-4T-4258
350 mm
Diameter:
EC axial fans
AC Axial fans Sickled blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400/230 V 50/60 Hz 135/170 W
Rated current
0.30/0.53/0.30/0.53 A
Rated speed
1330/1460 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
65/70 °C
Sound power level A weighted
72/75 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Compliant to
29.5 %
Measurement category
Fan with guard grill
A
Efficiency category
static
Efficiency grade N
41.2
Airflow Direction
NO
Sucking
R09R-3530HA-4T-4258
0309-4-1023
141 W
Blowing
R09R-3530HP-4T-4258
0309-4-1048
Variable speed drive Power input Air flow
2107 m³/h
Pressure drop
Type
Code
Weight (kg) AC axial fans Paddle blades
Overall efficiency
AC axial fans Plastic blades
Rated power input
AC axial fans Sickled blades
Frequency
3.7
74 Pa
Speed
1332 RPM
84
29
1.00 AC radial fans backward curved blades
Specific ratio
Aerodynamic characteristic 60Hz
ErP Data 350 376 442 460
6,5
50Hz 90 75
45 30
162
Accessories
psF [Pa]
60
15 0
1000
2000
3000
4000
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Fan with plate Airflow Direction
Type
Code
Sucking
R09P-3530HA-4T-4258
On request
Blowing
R09P-3530HP-4T-4258
On request
Weight (kg)
Connection diagram
0
Fan without guard grill 0301-1-0049 0301-1-0049
Page 146 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R09E-3530HA-4T-4258
On request
Blowing
R09E-3530HP-4T-4258
On request
Weight (kg)
37
AC Axial fans Sickled blades
450 mm
Diameter:
R13_-4530H_-4M-5066
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50 Hz
Rated power input
400 W
Rated current
1.80 A
Rated speed
1400 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
60 °C
Sound power level A weighted
72 dB (A)
Condensator
10 μF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Overall efficiency
Type
Code
Sucking R13R-4530HA-4M-5066 Blowing
R13R-4530HP-4M-5066
0313-4-1082 On request
Weight (kg)
10.0
27.5 %
Measurement category
A
Efficiency category
static
Efficiency grade N
36.1
Variable speed drive
NO
Power input
442 W
Air flow 96
4695 m³/h
Pressure drop
67 31
93 Pa
Speed
1370 RPM
Specific ratio
1.00
9,5
445 479 515 543
Aerodynamic characteristic 50Hz
ErP Data
150 125
psF [Pa]
100 198
75 50 25
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-4530HA-4M-5066
On request
Blowing
R13P-4530HP-4M-5066
On request
Weight (kg)
Type
Code
Sucking
R13E-4530HA-4M-5066
On request
Blowing
R13E-4530HP-4M-5066
On request
38
0
2000
4000
6000
8000
qv [m³/h] Fan characteristic measured in short bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
Fan without guard grill Airflow Direction
0
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
R13_-4530H_-4T2-5059
450 mm
Diameter:
EC axial fans
AC Axial fans Sickled blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V 50 Hz
Speed
AC axial fans Sickled blades
Frequency
high/low
Rated power input
465/330 W
Rated current
0.95/0.50 A
Rated speed
1400/1260 RPM
Min. ambient temperature
-30 °C 70 °C
Sound power level A weighted
73/69 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Max. ambient temperature
ErP data according to EU regulation 327/2011:
Fan with guard grill
29.3 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
37.5
Variable speed drive
NO
Power input
500 W
Air flow
Type
Code
Sucking
R13R-4530HA-4T2-5059
0313-4-1152
Blowing
R13R-4530HP-4T2-5059
On request
Weight (kg) AC axial fans Paddle blades
Overall efficiency
11.0
4631 m³/h
Pressure drop
118 Pa
Speed
71
1372 RPM 1.00
AC radial fans backward curved blades
Specific ratio
120 83
Aerodynamic characteristic Low Speed
ErP Data
445 465 485
High Speed 150 125
75
198
Accessories
psF [Pa]
100
50 25 0
2000
4000
6000
8000
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R13P-4530HA-4T2-5059
On request
Blowing
R13P-4530HP-4T2-5059
On request
Weight (kg)
Connection diagram
0
Fan with plate
Fan without guard grill 0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-4530HA-4T2-5059
On request
Blowing
R13E-4530HP-4T2-5059
On request
Weight (kg)
39
AC Axial fans Sickled blades
450 mm
Diameter:
R13_-4530H_-6T2-5065
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
170/105 W
Rated current
0.70/0.23 A
Rated speed
940/840 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
67/62 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
Aerodynamic characteristic
Fan with guard grill Airflow Direction
Code
Sucking
R13R-4530HA-6T2-5065
0313-4-1072
Blowing
R13R-4530HA-6T2-5065
On request
High Speed
Weight (kg)
60
11.0
120 83
Low Speed
70
50 psF [Pa]
Type
71
70 °C
Sound power level A weighted
40 30 20 10 0
0
1000
2000
3000
4000
5000
6000
445 465 485
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill
198
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-4530HA-6T2-5065
0313-4-1071
Blowing
R13P-4530HA-6T2-5065
On request
Weight (kg)
16.5
Fan without guard grill Airflow Direction
Type
Code
Sucking
R13E-4530HA-6T2-5065
0313-4-1062
Blowing
R13E-4530HA-6T2-5065
On request
40
Weight (kg)
8.1
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
R13_-5030H_-4M-7075
500 mm
Diameter:
EC axial fans
AC Axial fans Sickled blades
Nominal data according to standard EN 60335: Phase
1~ 230 V
Frequency
50 Hz
Rated power input
780 W
Rated current
3.50 A
Rated speed
1370 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
60 °C 76 dB (A)
Condensator
16 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
AC axial fans Sickled blades
Nominal voltage
ErP data according to EU regulation 327/2011:
Fan with guard grill
29.4 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
36.4 NO
Variable speed drive Power input
771 W
Air flow
Type
Code
Sucking
R13R-5030HA-4M-7075
0313-4-1081
Blowing
R13R-5030HP-4M-7075
On request
Weight (kg) AC axial fans Paddle blades
Overall efficiency
13.1
6829 m³/h
Pressure drop
125 Pa
Speed
71
1336 RPM
140
1.00
AC radial fans backward curved blades
Specific ratio
88
50Hz
497 520 540
Aerodynamic characteristic ErP Data
160 140 120
80
218
Accessories
psF [Pa]
100
60 40
Fan with plate
0
0
2000
4000
6000
8000
10000
qv [m³/h] Fan characteristic measured in short bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R13P-5030HA-4M-7075
0313-4-1120
Blowing
R13P-5030HP-4M-7075
On request
Weight (kg)
18.6
Connection diagram
20
Fan without guard grill 0301-1-0035 0301-1-0029
Page 146 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-5030HA-4M-7075
0313-4-1121
Blowing
R13E-5030HP-4M-7075
On request
Weight (kg)
10.7
41
AC Axial fans Sickled blades
500 mm
Diameter:
R13_-5030H_-4T2-7063
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
800/540 W
Rated current
1.90/0.95 A
Rated speed
1390/1200 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
45 °C
Sound power level A weighted
76/72 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Sucking Blowing
Type
R13R-5030HA-4T2-7063 R13R-5030HP-4T2-7063
Overall efficiency Code
0313-4-1038 On request
Weight (kg)
12.5
31.0 %
Measurement category
A
Efficiency category
static
Efficiency grade N
37.8
Variable speed drive
NO
Power input
828 W
Air flow 71
88
6489 m³/h
Pressure drop
140
150 Pa
Speed
1369 RPM
Specific ratio
1.00
497 520 540
Aerodynamic characteristic High Speed
Low Speed
ErP Data
120 100
psF [Pa]
80 218
60 40 20
Fan with plate Airflow Direction
Type
Sucking
R13P-5030HA-4T2-7063
0313-4-1028
Blowing
R13P-5030HP-4T2-7063
On request
Code
Weight (kg)
18.0
Fan without guard grill Airflow Direction
Type
Code
Sucking
R13E-5030HA-4T2-7063
0313-4-1068
Blowing
R13E-5030HP-4T2-7063
On request
42
Weight (kg)
10.1
0
0
2000
4000
6000
8000
10000
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
R13_-5030H_-6M-5072
500 mm
Diameter:
EC axial fans
AC Axial fans Sickled blades
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V 50/60 Hz
Rated power input
245/320 W
Rated current
1.10/1.35 A
Rated speed
900/1030 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
60 °C 72/76 dB (A)
Condensator
8 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
AC axial fans Sickled blades
Frequency
Aerodynamic characteristic
Fan with guard grill 60Hz
Airflow Direction
psF [Pa]
80
Type
Code
Sucking
R13R-5030HA-6M-5072
0313-4-1083
Blowing
R13R-5030HP-6M-5072
On request
Weight (kg) AC axial fans Paddle blades
50Hz 100
10.3
60 40
71
120 88
0
0
2000
4000
6000
AC radial fans backward curved blades
20
8000 497 520 540
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill
Accessories
198
Fan with plate Type
Code
Sucking
R13P-5030HA-6M-5072
0313-4-1105
Blowing
R13P-5030HP-6M-5072
On request
Weight (kg)
15.8
Connection diagram
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Fan without guard grill 0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-5030HA-6M-5072
0313-4-1104
Blowing
R13E-5030HP-6M-5072
On request
Weight (kg)
7.9
43
AC Axial fans Sickled blades
500 mm
Diameter:
R13_-5030H_-6M-5071
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
280/370 W
Rated current
1.20/1.50 A
Rated speed
890/1000 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
55 °C
Sound power level A weighted
terminal box
Insulation class
155
Protection class
IP54
Code
Sucking
R13R-5030HA-6M-5071
0313-4-1080
Blowing
R13R-5030HP-6M-5071
On request
50Hz
Weight (kg)
100
10.5
80
psF [Pa]
Type
71
8 µF/450 V
Connection
Aerodynamic characteristic
Fan with guard grill Airflow Direction
75/78 dB (A)
Condensator
120 88
60Hz
60 40 20 0
0
2000
4000
6000
8000
497 520 540
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill
198
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-5030HA-6M-5071
0309-4-1102
Blowing
R13P-5030HP-6M-5071
On request
Weight (kg)
16.0
Fan without guard grill Airflow Direction
Type
Code
Sucking
R13E-5030HA-6M-5071
0313-4-1101
Blowing
R13E-5030HP-6M-5071
On request
44
Weight (kg)
8.0
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
R13_-5030H_-6T2-5068
500 mm
Diameter:
EC axial fans
AC Axial fans Sickled blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V 50 Hz
Speed
AC axial fans Sickled blades
Frequency
high/low
Rated power input
210/150 W
Rated current
0.60/0.27 A
Rated speed
960/880 RPM
Min. ambient temperature
-30 °C 60 °C
Sound power level A weighted
72/70 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Max. ambient temperature
Aerodynamic characteristic
Fan with guard grill Low Speed
Airflow Direction
psF [Pa]
80
Type
Code
Sucking
R13R-5030HA-6T2-5068
0313-4-1089
Blowing
R13R-5030HP-6T2-5068
On request
Weight (kg) AC axial fans Paddle blades
High Speed 100
10.3
60 40
71
120 88
0
0
1000
2000
3000
4000
5000
6000
AC radial fans backward curved blades
20
7000 497 520 540
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill
Accessories
198
Fan with plate Type
Code
Sucking
R13P-5030HA-6T2-5068
0313-4-1090
Blowing
R13P-5030HP-6T2-5068
On request
Weight (kg)
15.8
Connection diagram
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Fan without guard grill 0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-5030HA-6T2-5068
0313-4-1088
Blowing
R13E-5030HP-6T2-5068
On request
Weight (kg)
7.9
45
AC Axial fans Sickled blades
500 mm
Diameter:
R13_-5030H_-6T2-5065
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
255/175 W
Rated current
0.67/0.31 A
Rated speed
960/870 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
65 °C
Sound power level A weighted
73/71 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Sucking Blowing
Type
R13R-5030HA-6T2-5065 R13R-5030HP-6T2-5065
Overall efficiency Code
0303-4-1086 On request
Weight (kg)
10.5
27.3 %
Measurement category
A
Efficiency category
static
Efficiency grade N
37.1
Variable speed drive
NO
Power input
285 W
Air flow 71
4335 m³/h
Pressure drop
120 88
67 Pa
Speed
939 RPM
Specific ratio
1.00
Aerodynamic characteristic 497 520 540
High Speed
Low Speed
ErP Data
100
psF [Pa]
75
198
50
25
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-5030HA-6T2-5065
0313-4-1087
Blowing
R13P-5030HP-6T2-5065
On request
Weight (kg)
16.0
Fan without guard grill Airflow Direction
Type
Code
Sucking
R13E-5030HA-6T2-5065
0313-4-1063
Blowing
R13E-5030HP-6T2-5065
On request
46
Weight (kg)
8.0
0
0
1000
2000
3000
4000
5000
6000
7000
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
R13_-5630H_-6M-7036
560 mm
Diameter:
EC axial fans
AC Axial fans Sickled blades
Nominal data according to standard EN 60335: Phase
1~ 230 V
Frequency
50 Hz
Rated power input
420 W
Rated current
1.90 A
Rated speed
865 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
55 °C
Sound power level A weighted
AC axial fans Sickled blades
Nominal voltage
76 dB (A) 12.5 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Condensator
Aerodynamic characteristic
Fan with guard grill Airflow Direction
100
Sucking R13R-5630HA-6M-7036
80
psF [Pa]
Type
Blowing
R13R-5630HP-6M-7036
Code
0313-4-1007 On request
Weight (kg) AC axial fans Paddle blades
50Hz
13.3
60 40
71
140 93
0
0
2000
4000
6000
8000
AC radial fans backward curved blades
20
10000 552 579 601
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill
Accessories
218
Fan with plate Type
Code
Sucking
R13P-5630HA-6M-7036
0309-4-1031
Blowing
R13P-5630HP-6M-7036
On request
Weight (kg)
21.0
Connection diagram
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Fan without guard grill 0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-5630HA-6M-7036
0313-4-1066
Blowing
R13E-5630HP-6M-7036
On request
Weight (kg)
10.5
47
AC Axial fans Sickled blades
560 mm
Diameter:
R13_-5630H_-6T2-7008
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
380/250 W
Rated current
0.85/0.44 A
Rated speed
910/760 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
Compliant to
Fan with guard grill Airflow Direction
Sucking Blowing
Type
R13R-5630HA-6T2-7008 R13R-5630HP-6T2-7008
70 °C
Sound power level A weighted
76/71 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011: Overall efficiency
Code
0313-4-1011 On request
Weight (kg)
13.3
31.4 %
Measurement category
A
Efficiency category
static
Efficiency grade N
40.2
Variable speed drive
NO
Power input
411 W
Air flow 71
5423 m³/h
Pressure drop
140 93
90 Pa
Speed
920 RPM
Specific ratio
1.00
Aerodynamic characteristic 552 579 601
High speed
Low speed
ErP Data
100
psF [Pa]
75
218
50
25
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-5630HA-6T2-7008
0313-4-1015
Blowing
R13P-5630HP-6T2-7008
On request
Weight (kg)
21.0
Fan without guard grill Airflow Direction
Type
Code
Sucking
R13E-5630HA-6T2-7008
0313-4-1045
Blowing
R13E-5630HP-6T2-7008
On request
48
Weight (kg)
10.5
0
0
2000
4000
6000
8000
10000
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
R13_-6330H_-6M-X055
630 mm
Diameter:
EC axial fans
AC Axial fans Sickled blades
Nominal data according to standard EN 60335: Phase
1~ 230 V
Frequency
50 Hz
Rated power input
680 W
Rated current
3.10 A
Rated speed
890 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
50 °C 77 dB (A)
Condensator
18 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
AC axial fans Sickled blades
Nominal voltage
Aerodynamic characteristic
Fan with guard grill
120
Airflow Direction
100
psF [Pa]
80
Type
Code
Sucking
R13R-6330HA-6M-X055
0313-4-1005
Blowing
R13R-6330HP-6M-X055
On request
Weight (kg) AC axial fans Paddle blades
50Hz
17.0
60 55
40
109
186
0
0
2000
4000
6000
8000
10000
AC radial fans backward curved blades
20 12000 627 654 674
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill
Accessories
248
Fan with plate Type
Code
Sucking
R13P-6330HA-6M-X055
0309-4-1031
Blowing
R13P-6330HP-6M-X055
On request
Weight (kg)
24.7
Connection diagram
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Fan without guard grill 0301-1-0035 0301-1-0029
Page 146 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-6330HA-6M-X055
0313-4-1061
Blowing
R13E-6330HP-6M-X055
On request
Weight (kg)
14.2
49
AC Axial fans Sickled blades
630 mm
Diameter:
R13_-6330H_-6T2-7042
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
600/380 W
Rated current
1.25/0.65 A
Rated speed
870/640 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
40 °C
Sound power level A weighted
77/73 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Sucking Blowing
Type
R13R-6330HA-6T2-7042 R13R-6330HP-6T2-7042
Overall efficiency Code
0313-4-1000 On request
Weight (kg)
14.5
31.8 %
Measurement category
A
Efficiency category
static
Efficiency grade N
39.2
Variable speed drive
NO
Power input
680 W
Air flow 55
7593 m³/h
Pressure drop
156 109
107 Pa
Speed
877 RPM
Specific ratio
1.00
Aerodynamic characteristic 627 654 676
High speed
Low speed
ErP Data
120 100
psF [Pa]
80 218
60 40 20
Fan with plate Airflow Direction
Type
Sucking
R13P-6330HA-6T2-7042
0313-4-1013
Blowing
R13P-6330HP-6T2-7042
On request
Code
Weight (kg)
23.3
Fan without guard grill Airflow Direction
Type
Code
Sucking
R13E-6330HA-6T2-7042
0313-4-1042
Blowing
R13E-6330HP-6T2-7042
On request
50
Weight (kg)
10.8
0
0
2000
4000
6000
8000
10000
12000
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
R13_-6330H_-8T2-7038
630 mm
Diameter:
EC axial fans
AC Axial fans Sickled blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V 50 Hz
Speed
AC axial fans Sickled blades
Frequency
high/low
Rated power input
280/175 W
Rated current
0.68/0.30 A
Rated speed
650/510 RPM
Min. ambient temperature
-30 °C 70 °C
Sound power level A weighted
71/66 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Max. ambient temperature
Aerodynamic characteristic
Fan with guard grill Low speed
Airflow Direction
70 60
Type
Code
Sucking
R13R-6330HA-8T2-7038
0313-4-1023
Blowing
R13R-6330HP-8T2-7038
On request
Weight (kg) AC axial fans Paddle blades
psF [Pa]
High speed 80
14.5
50 40 55
30
156 109
AC radial fans backward curved blades
20 10 0
0
2000
4000
6000
8000
10000 627 654 676
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill
Accessories
218
Fan with plate Type
Code
Sucking
R13P-6330HA-8T2-7038
0313-4-1030
Blowing
R13P-6330HP-8T2-7038
On request
Weight (kg)
23.3
Connection diagram
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Fan without guard grill 0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-6330HA-8T2-7038
0313-4-1043
Blowing
R13E-6330HP-8T2-7038
On request
Weight (kg)
10.8
51
AC Axial fans Sickled blades
630 mm
Diameter:
R13_-6330H_-12T2-7051
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
112/58 W
Rated current
0.33/0.13 A
Rated speed
430/330 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70 °C
Sound power level A weighted
63/53 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Fan with guard grill Airflow Direction
Type
Code
Sucking
R13R-6330HA-12T2-7051
0313-4-1041
Blowing
R13R-6330HP-12T2-7051
On request
Weight (kg)
Aerodynamic characteristic High speed
Low speed
35
14.5
30 25
156 109
psF [Pa]
55
20 15 10 5
627 654 676
0
0
1000
2000
3000
4000
5000
6000
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill
218
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-6330HA-12T2-7051
0313-4-1037
Blowing
R13P-6330HP-12T2-7051
On request
Weight (kg)
23.3
Fan without guard grill Airflow Direction
Type
Code
Sucking
R13E-6330HA-12T2-7051
0313-4-1044
Blowing
R13E-6330HP-12T2-7051
On request
52
Weight (kg)
10.8
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
R18_-6330H_-4T2-X003
630 mm
Diameter:
EC axial fans
AC Axial fans Sickled blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V 50 Hz
Speed
AC axial fans Sickled blades
Frequency
high/low
Rated power input
2350/1360 W
Rated current
4.65/2.75 A
Rated speed
1360/1000 RPM
Min. ambient temperature
-30 °C 50 °C
Sound power level A weighted
89/83 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Max. ambient temperature
Aerodynamic characteristic Low speed
250 200
Airflow Direction
Type
Code
Weight (kg)
Sucking
R18R-6330HA-4T2-X003
0318-4-1014
30.5
AC axial fans Paddle blades
Fan with guard grill
High speed
psF [Pa]
150 100
98
175 113
0
0
4000
8000
12000
16000
AC radial fans backward curved blades
50
20000 624 659 697
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill
Accessories
273
General notes Connection diagram Accessories Compliant to standards
Airflow Direction
Type
Code
Weight (kg)
Sucking
R18P-6330HA-4T2-X003
0318-4-0020
39.0
Connection diagram
Fan with plate
Fan without guard grill 0301-1-0031
Page 147 Page 134 Page 28
Airflow Direction
Type
Code
Weight (kg)
Sucking
R18E-6330HA-4T2-X003
0318-4-0010
26.0 53
AC Axial fans Sickled blades
710 mm
Diameter:
R18_-7130H_-6T2-7502
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
990/650 W
Rated current
1.90/1.20 A
Rated speed
870/620 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70 °C
Sound power level A weighted
78/74 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Sucking
Type
R18R-7130HA-6T2-7502
Overall efficiency Code
0318-4-0007
Weight (kg)
27.2
29.8 %
Measurement category
A
Efficiency category
static
Efficiency grade N
36.1
Variable speed drive
NO
Power input
998 W
Air flow 94
12977 m³/h
Pressure drop
147 118
86 Pa
Speed
888 RPM
Specific ratio
1.00
Aerodynamic characteristic 702 730 772
High speed
Low speed
120 100
psF [Pa]
80
241
60 40 20 0
Fan with plate
4000
8000
12000
16000
20000
qv [m³/h]
Airflow Direction
Type
Code
Weight (kg)
Sucking
R18P-7130HA-6T2-7502
0318-4-0003
34.9
Fan without guard grill Airflow Direction
Type
Code
Weight (kg)
Sucking
R18E-7130HA-6T2-7502
0318-4-0016
22.0
54
0
Fan characteristic measured in full bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram Accessories Compliant to standards
0301-1-0031
Page 147 Page 134 Page 28
R18_-8030H_-6T2-X004
800 mm
Diameter:
EC axial fans
AC Axial fans Sickled blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V 50 Hz
Speed
AC axial fans Sickled blades
Frequency
high/low
Rated power input
1560/1050 W
Rated current
3.50/2.00 A
Rated speed
900/700 RPM
Min. ambient temperature
-30 °C 60 °C
Sound power level A weighted
82/77 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Max. ambient temperature
ErP data according to EU regulation 327/2011:
Fan with guard grill
31.6 %
Measurement category
A
Efficiency category
static
Airflow Direction
Type
Code
Weight (kg)
Efficiency grade N
36.5
Sucking
R18R-8030HA-6T2-X004
0318-4-0026
32.8
Variable speed drive
AC axial fans Paddle blades
Overall efficiency
NO
Power input
1716 W
Air flow
17772 m³/h
Pressure drop
114 Pa
Speed
99
912 RPM 1.00
AC radial fans backward curved blades
Specific ratio
175 120
Aerodynamic characteristic Low speed
785 816 860
High speed 200
100 274
Accessories
psF [Pa]
150
50
0
5000
10000 15000 qv [m³/h]
20000
25000
Fan characteristic measured in full bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram Accessories Compliant to standards
Fan with plate Airflow Direction
Type
Code
Weight (kg)
Sucking
R18P-8030HA-6T2-X004
0318-4-0028
45.7
Connection diagram
0
Fan without guard grill 0301-1-0031
Page 147 Page 134 Page 28
Airflow Direction
Type
Code
Weight (kg)
Sucking
R18E-8030HA-6T2-X004
0318-4-0029
27.0 55
AC Axial fans Sickled blades
800 mm
Diameter:
R18_-8030H_-6T2-X001
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
2000/1050 W
Rated current
4.0/2.3 A
Rated speed
890/630 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
50 °C
Sound power level A weighted
81/75 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Sucking
Type
R18R-8030HA-6T2-X001
Overall efficiency Code
0318-4-0005
Weight (kg)
34.8
31.7 %
Measurement category
A
Efficiency category
static
Efficiency grade N
36.1
Variable speed drive
NO
Power input
2032 W
Air flow 99
18059 m³/h
Pressure drop
175 120
129 Pa
Speed
890 RPM
Specific ratio
1.00
Aerodynamic characteristic 785 821 860
High speed
Low speed
ErP Data
180 160 140 psF [Pa]
120
274
100 80 60 40 20 0
Fan with plate
5000
10000
15000
20000
25000
30000
qv [m³/h]
Airflow Direction
Type
Code
Weight (kg)
Sucking
R18P-8030HA-6T2-X001
0318-4-0001
47.7
Fan without guard grill Airflow Direction
Type
Code
Weight (kg)
Sucking
R18E-8030HA-6T2-X001
0318-4-0009
29.0
56
0
Fan characteristic measured in full bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram Accessories Compliant to standards
0301-1-0031
Page 147 Page 134 Page 28
R18_-8030H_-8T2-X000
800 mm
Diameter:
EC axial fans
AC Axial fans Sickled blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V 50 Hz
Speed
AC axial fans Sickled blades
Frequency
high/low
Rated power input
920/600 W
Rated current
2.3/1.15 A
Rated speed
680/560 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
60 °C
Sound power level A weighted
77/69.5 dB (A) terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Connection
ErP data according to EU regulation 327/2011:
Fan with guard grill
30.8 %
Measurement category
A
Efficiency category
static
Airflow Direction
Type
Code
Weight (kg)
Efficiency grade N
37.2
Sucking
R18R-8030HA-8T2-X000
0318-4-0004
34.8
Variable speed drive
NO
Power input
AC axial fans Paddle blades
Overall efficiency
984 W
Air flow
12343 m³/h
Pressure drop
92 Pa
Speed
99
687 RPM 1.00
AC radial fans backward curved blades
Specific ratio
175 120
Aerodynamic characteristic Low speed
ErP Data
785 821 860
High speed 120 105 90
60 274
45
Accessories
psF [Pa]
75
30 15 0
5000
10000
15000
20000
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram Accessories Compliant to standards
Fan with plate Airflow Direction
Type
Code
Weight (kg)
Sucking
R18P-8030HA-8T2-X000
0318-4-0000
47.7
Connection diagram
0
Fan without guard grill 0301-1-0031
Page 147 Page 134 Page 28
Airflow Direction
Type
Code
Weight (kg)
Sucking
R18E-8030HA-8T2-X000
0318-4-0008
29.0 57
AC Axial fans Sickled blades
800 mm
Diameter:
R18_-8030H_-12T2-7505
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
330/170 W
Rated current
1.20/0.50 A
Rated speed
450/320 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
Type
66/58 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
Aerodynamic characteristic
Fan with guard grill Airflow Direction
70 °C
Sound power level A weighted
Code
Sucking R18R-8030HA-12T2-7505 0318-4-0017
High speed
Weight (kg)
40
34.8
35
Low speed
30
99
psF [Pa]
25 147 120
20 15 10 5 0
0
3000
6000
9000
12000
15000
785 816 860
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill
246
Fan with plate Airflow Direction
Type
Code
Sucking R18P-8030HA-12T2-7505 0318-4-0032
Weight (kg)
47.7
Fan without guard grill Airflow Direction
Type
Code
Sucking R18E-8030HA-12T2-7505 0318-4-0033 58
Weight (kg)
29.0
General notes Connection diagram Accessories Compliant to standards
0301-1-0031
Page 147 Page 134 Page 28
Connection diagram
Accessories
AC radial fans backward curved blades
AC axial fans Paddle blades
AC axial fans Plastic blades
AC axial fans Sickled blades
EC axial fans
AC Axial fans Sickled blades
59
03 AC Axial fans Plastic blades
60
AC axial fans Paddle blades
AC axial fans Plastic blades
AC axial fans Sickled blades
EC axial fans
AC Axial fans Plastic blades
AC radial fans backward curved blades
AC Axial fans Plastic blades
Connection diagramS
Accessories
XXX Arciis erchic temolor empeles nam, quo tectorehenem fuga. Nam as simagniscia aut repelist quam sa que occae. Nemporionse volum none sam, sequae natur sus etur, nihil ipis aut es seque nations ecescit voluptatent ma nos aut ex et volorepedis et aut ut lamus et porem escit, earum.
61
AC Axial fans Plastic blades
62
AC Axial fans Plastic blades
AC axial fans Sickled blades
EC axial fans
Axial fans with induction (AC) motors and plastic blades Plastic blades (SP)
AC axial fans Plastic blades
Diameter: 300 mm
Plastic blades (AP)
AC axial fans Paddle blades
Diameters: 400 – 450 mm
Plastic blades (SP, LP)
AC radial fans backward curved blades
Diameters: 400 – 450 mm
Example of type key:
R11R-45SPS-4T2-5745 R11 External rotor motor type (R09, R11)
Accessories
R Acessory type (E ‒ without guard grill, R ‒ with guard grill, P ‒ with guard grill and wall plate) 45 Fan diameter x 10 (exact diameters are stated in drawings) SP Type of blabes (AP, KP, LP, SP) S Airflow direction (S ‒ sucking, B ‒ blowing)
Connection diagramS
4 Number of motor poles T Number of phases (M ‒ single phase, T ‒ three phase) 2 Number of motor speed 57 Motor steck height 45 Version of electrical construction
63
AC Axial fans Plastic blades
300 mm
Diameter:
R09_-30SP_-4M-2543
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
65/90 W
Rated current
0.30/0.40 A
Rated speed
1400/1500 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70 °C
Sound power level A weighted
65/70 dB (A)
Condensator
2 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Type
Code
Sucking
R09R-30SPS-4M-2543
0309-4-1091
Blowing
R09R-30SPB-4M-2543
0309-4-1092
Weight (kg)
3.0
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Aerodynamic characteristic 50 Hz
60 Hz
75 72
35
60
6,5
300 323 360 380
psF [Pa]
45 30 15 0
0
500
1000
1500
2000
2500
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill 138
Fan with plate Airflow Direction
Type
Code
Sucking
R09P-30SPS-4M-2543
On request
Blowing
R09P-30SPB-4M-2543
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R09E-30SPS-4M-2543
On request
Blowing
R09E-30SPB-4M-2543
On request
64
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0043 0301-1-0044
Page 145 Page 134 Page 28
R11_-35KP_-4M-3808
350 mm
Diameter:
EC axial fans
AC Axial fans Plastic blades
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V 50/60 Hz
Rated power input
110/145 W
Rated current
0.45/0.65 A
Rated speed
1360/1490 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
55 °C 65/69 dB (A)
Condensator
4 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
AC axial fans Sickled blades
Frequency
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Aerodynamic characteristic 50 Hz
60 Hz
Type
Code
Sucking
R11R-35KPA-4M-3808
0311-4-0243
Blowing
R11R-35KPP-4M-3808
On request
Weight (kg) AC axial fans Paddle blades
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
5.5
75 60
84
52 22
AC radial fans backward curved blades
30
0
350 376 442 458
15
0
500
1000
1500
2000
2500
3000
6,5
psF [Pa]
45
3500
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill
Accessories
190
Fan with plate Type
Code
Sucking
R11P-35KPA-4M-3808
On request
Blowing
R11P-35KPP-4M-3808
On request
Weight (kg)
Fan without guard grill 0301-1-0043 0301-1-0044
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R11E-35KPA-4M-3808
On request
Blowing
R11E-35KPP-4M-3808
On request
Weight (kg)
65
Connection diagramS
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
AC Axial fans Plastic blades
360 mm
Diameter:
R09_-36LP_-6M-4249
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
65/70 W
Rated current
0.30/0.32 A
Rated speed
830/900 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
60 °C
Sound power level A weighted
52 / 55 dB (A)
Condensator
1.5 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Type
Code
Weight (kg)
Sucking
R09R-36LPS-6M-4249
0309-4-0436
3.8
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Aerodynamic characteristic 50 Hz
60 Hz
40 88
90
20
10
9
360 437 490 510
psF [Pa]
30
0
0
500
1000
1500
2000
2500
qv [m³/h] Fan characteristic measured in full bell mouth with guard grill 189
Fan with plate Airflow Direction
Type
Code
Sucking
R09P-36LPS-6M-4249
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R09E-36LPS-6M-4249
On request
66
Weight (kg)
General notes Connection diagram Accessories Compliant to standards
0301-1-0044
Page 145 Page 134 Page 28
R11_-40LP_-4M-5150
400 mm
Diameter:
EC axial fans
AC Axial fans Plastic blades
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Rated current
0.85/1.10 A
Rated speed
1310/1450 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
60 °C
Sound power level A weighted
73/76 dB (A)
Condensator
6.3 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54 Compliant to
ErP data according to EU regulation 327/2011: Overall efficiency
Fan with guard grill
30.9 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
41.5
Sucking
R11R-40LPS-4M-5150
0311-4-0313
Variable speed drive
NO
Blowing
R11R-40LPB-4M-5150
0311-4-0342
Power input
AC axial fans Plastic blades
190/260 W
AC axial fans Sickled blades
50/60 Hz
Rated power input
208 W
Type
Code
Weight (kg) AC axial fans Paddle blades
Frequency
6.0
2800 m3/h
Air flow Pressure drop
86 Pa
Speed
105
1314 RPM 1.00
AC radial fans backward curved blades
Specific ratio
41 8
60 Hz
ErP Data
395 420 470 490
50 Hz 100
9,5
Aerodynamic characteristic
80
psF [Pa]
60
20
Fan with plate 0
1000
2000
3000
4000
5000
qv [m³/h] Fan characteristic measured in short bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R11P-40LPS-4M-5150
On request
Blowing
R11P-35KPP-4M-3808
On request
Weight (kg) Connection diagramS
0
Accessories
200
40
Fan without guard grill 0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
Airflow Direction
Type
Sucking
R11P-40LPB-4M-5150
On request
Blowing
R11E-40LPB-4M-5150
On request
Code
Weight (kg)
67
AC Axial fans Plastic blades
400 mm
Diameter:
R11_-40LP_-6M-3806
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
85/110 W
Rated current
0.38/0.48 A
Rated speed
870/980 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
60 °C
Sound power level A weighted Condensator
3.15 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Type
Code
Sucking
R11R-40LPS-6M-3806
On request
Blowing
R11R-40LPB-6M-3806
On request
Weight (kg)
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Aerodynamic characteristic 50 Hz
60 Hz
40 31 7
30
20
10
9,5
395 420 470 490
psF [Pa]
105
0
0
500
1000
1500
2000
2500
3000
3500
qv [m³/h] Fan characteristic measured in short bell mouth with guard grill 190
Fan with plate Airflow Direction
Type
Code
Sucking
R11P-40LPS-6M-3806
On request
Blowing
R11P-40LPB-6M-3806
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R11P-40LPS-6M-3806
On request
Blowing
R09E-30SPB-4M-2543
On request
68
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0043 0301-1-0044
Page 145 Page 134 Page 28
R11_-42LP_-4M-5150
420 mm
Diameter:
EC axial fans
AC Axial fans Plastic blades
Nominal data according to standard EN 60335: Phase
1~ 230 V
Frequency
50 Hz
Rated power input
220 W
Rated current
1.00 A
Rated speed
1280 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
60 °C 76 dB (A)
Condensator
6.3 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
AC axial fans Sickled blades
Nominal voltage
ErP data according to EU regulation 327/2011:
Fan with guard grill
28.9 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
39.2 NO
Variable speed drive Power input
231 W
Type
Code
Sucking
R11R-42LPS-4M-5150
0311-4-0312
Blowing
R11R-42LPB-4M-5150
0311-4-0310
Weight (kg) AC axial fans Paddle blades
Overall efficiency
6.1
2948 m3/h
Air flow Pressure drop
84 Pa
Speed
100
46 13
1259 RPM 1.00
AC radial fans backward curved blades
Specific ratio
ErP Data
415 458 502 522
50 Hz 90
9,5
Aerodynamic characteristic
75
200
30 15 0
Accessories
45
Fan with plate 0
1500
3000
4500
6000
qv [m³/h] Fan characteristic measured in short bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R11P-42LPS-4M-5150
On request
Blowing
R11P-42LPB-4M-5150
On request
Weight (kg)
Fan without guard grill 0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R11E-42LPS-4M-5150
On request
Blowing
R11E-42LPB-4M-5150
On request
Weight (kg)
69
Connection diagramS
psF [Pa]
60
AC Axial fans Plastic blades
420 mm
Diameter:
R11_-42AP_-6M-5758
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
120/165 W
Rated current
0.52/0.72 A
Rated speed
880/900 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70/55 °C
Sound power level A weighted Condensator
3.15 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Type
Code
Sucking
R11R-42APS-6M-5758
0311-4-0462
Blowing
R11R-42APB-6M-5758
On request
Weight (kg)
6.8
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Aerodynamic characteristic 50 Hz
60 Hz
150 125
62 36
psF [Pa]
89
75
9,5
417 435 483 507
50 25 0
0
500
1000
1500
2000
2500
3000
3500
qv [m³/h] Fan characteristic measured in short bell mouth with guard grill 204
Fan with plate Airflow Direction
Type
Code
Sucking
R11P-42APS-6M-5758
On request
Blowing
R11P-42APB-6M-5758
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R11E-42APS-6M-5758
On request
Blowing
R11E-42APB-6M-5758
On request
70
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
R11_-45LP_-4M-5150
EC axial fans
AC Axial fans Plastic blades
450 mm
Diameter:
Nominal data according to standard EN 60335: Phase
1~ 230 V
Frequency
50 Hz
Rated power input
240 W
Rated current
1.10 A
Rated speed
1230 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
50 °C 78 dB (A)
Condensator
6.3 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
AC axial fans Sickled blades
Nominal voltage
ErP data according to EU regulation 327/2011:
Fan with guard grill
26.6 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
36.6
Sucking
R11R-45LPS-4M-5150
0311-4-0314
NO
Blowing
R11R-45LPB-4M-5150
0311-4-0343
Variable speed drive Power input
258 W
Type
Code
Weight (kg) AC axial fans Paddle blades
Overall efficiency
6.4
3416 m3/h
Air flow Pressure drop
76 Pa
Speed
89
1207 RPM
57
1.00
AC radial fans backward curved blades
Specific ratio
24
ErP Data
445 480 520 540
50 Hz
9,5
Aerodynamic characteristic 90 75
45
200
Accessories
psF [Pa]
60
30 15
0
1500
3000
4500
6000
qv [m³/h] Fan characteristic measured in short bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R11P-45LPS-4M-5150
On request
Blowing
R11P-45LPB-4M-5150
On request
Weight (kg) Connection diagramS
0
Fan with plate
Fan without guard grill 0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R11E-45LPS-4M-5150
On request
Blowing
R11E-45LPB-4M-5150
On request
Weight (kg)
71
AC Axial fans Plastic blades
450 mm
Diameter:
R11_-45LP_-6M-5105
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
125/165 W
Rated current
0.55/0.70 A
Rated speed
890/1000 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
50 °C
Sound power level A weighted
5 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
Aerodynamic characteristic
Fan with guard grill Airflow Direction
Code
Sucking
R11R-45LPS-6M-5105
0311-4-0300
Blowing
R11R-45LPB-6M-5105
On request
50 Hz
Weight (kg)
24
60 Hz
60 50
6.4
40 psF [Pa]
Type
89
76/70 dB (A)
Condensator
57
30 20 10 0
0
1000
2000
4000
5000
qv [m³/h]
9,5
445 480 520 540
3000
Fan characteristic measured in short bell mouth with guard grill ErP characteristic measured in full bell mouth without guard grill
200
Fan with plate Airflow Direction
Type
Code
Sucking
R11P-45LPS-6M-5105
On request
Blowing
R11P-45LPB-6M-5105
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R11E-45LPS-6M-5105
On request
Blowing
R11E-45LPB-6M-5105
On request
72
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
R11_-45SP_-6M-5761
450 mm
Diameter:
EC axial fans
AC Axial fans Plastic blades
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V 115/150 W
Rated current
0.50/0.65 A
Rated speed
800/880 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
65 °C
Sound power level A weighted
83/87 dB (A)
Condensator
3.15 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Sickled blades
50/60 Hz
Rated power input
AC axial fans Plastic blades
Frequency
ErP data according to EU regulation 327/2011:
Fan with guard grill Type
Code
Sucking
R11R-45SPS-6M-5761
0311-4-0403
Blowing
R11R-45SPB-6M-5761
On request
89
Aerodynamic characteristic 50 Hz
Weight (kg) AC axial fans Paddle blades
Airflow Direction
62 36
AC radial fans backward curved blades
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
60 Hz
445 480 520 540
40
9,5
50
psF [Pa]
30 20 10
1000
2000
3000
4000
5000
qv [m³/h]
Fan with plate
Fan characteristic measured in short bell mouth with guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Accessories
0
Airflow Direction
Type
Code
Sucking
R11P-45SPS-6M-5761
On request
Blowing
R11P-45SPB-6M-5761
On request
Weight (kg) Connection diagramS
0
204
Fan without guard grill 0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R11E-45SPS-6M-5761
On request
Blowing
R11E-45SPB-6M-5761
On request
Weight (kg)
73
04 AC Axial fans Paddle blades
74
AC axial fans Paddle blades
AC axial fans Plastic blades
AC axial fans Sickled blades
EC axial fans
AC Axial fans Paddle blades
AC radial fans backward curved blades
AC Axial fans Paddle blades
Connection diagramS
Accessories
XXX Arciis erchic temolor empeles nam, quo tectorehenem fuga. Nam as simagniscia aut repelist quam sa que occae. Nemporionse volum none sam, sequae natur sus etur, nihil ipis aut es seque nations ecescit voluptatent ma nos aut ex et volorepedis et aut ut lamus et porem escit, earum.
75
AC Axial fans Paddle blades
76
AC Axial fans Paddle blades
AC axial fans Sickled blades
EC axial fans
Axial fans with induction (AC) motors and paddle blades Stamped steel blades (type 25 °)
AC axial fans Plastic blades
Diameters: 200-250 mm
Stamped steel blades (type 28 °, 30 °, 32 °)
AC axial fans Paddle blades
Diameters: 250-350 mm
Stamped aluminium blades (type 25 °, 30 °, 35 °)
AC radial fans backward curved blades
Diameters: 400-630 mm
Example of type key:
R11R-4030A-4T2-3830 R11 External rotor motor type (R09, R11, R13)
Accessories
R Acessory type (E ‒ without guard grill, R ‒ with guard grill, P ‒ with guard grill and wall plate) 40 Fan diameter x 10 (exact diameters are stated in drawings) 30 Type of blabes (25 °, 30 °, 35 °) A Airflow direction (A ‒ sucking, P ‒ blowing)
Connection diagramS
4 Number of motor poles T Number of phases (M ‒ single phase, T ‒ three phase) 2 Number of motor speed 38 Motor steck height 30 Version of electrical construction
77
AC Axial fans Paddle blades
200 mm
Diameter:
R09_-2025_-2M-1511
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
45/55 W
Rated current
0.21/0.24 A
Rated speed
2580/2850 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70 °C
Sound power level A weighted
66/69 dB (A)
Condensator
1.5 µF/450 V
Connection
cable
Insulation class
155
Protection class
IP44
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Fan with guard grill Airflow Direction
Type
Code
Sucking
R09R-2025M-2M-1511
0309-4-0190
Blowing
R09R-2025M-2M-1511
0309-4-0214
Weight (kg)
Aerodynamic characteristic 50 Hz
60 Hz
90
1.6
75 60 14
32
psF [Pa]
45
45 30 15
197 230 260 274 6,5
0
0
200
400 600 qv [m³/h]
800
1000
500 85
Fan characteristic measured in full bell mouth with guard grill
77
Fan with plate Airflow Direction
Type
Code
Sucking
R09P-2025M-2M-1511
On request
Blowing
R09P-2025M-2M-1511
0309-4-0171
Weight (kg)
2.3
Fan without guard grill Airflow Direction
Type
Code
Sucking
R09E-2025M-2M-1511
On request
Blowing
R09E-2025M-2M-1511
On request
78
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0026 0301-1-0042
Page 145 Page 134 Page 28
R09_-2025_-4M-2516
250 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V 50/60 Hz
Rated power input
AC axial fans Sickled blades
Frequency
30/38 W
Rated current
0.14/0.17 A
Rated speed
1430/1680 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
65 °C 52/54 dB (A)
Condensator
1.5 µF/450 V
Connection
cable
Insulation class
155
Protection class
IP44
AC axial fans Plastic blades
Sound power level A weighted
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Fan with guard grill 50 Hz
60 Hz
50
Airflow Direction
Type
Sucking
R09R-2025M-4M-2516
0309-4-0211
Blowing
R09R-2025M-4M-2516
0309-4-0261
Code
Weight (kg) AC axial fans Paddle blades
Aerodynamic characteristic
3.4
30
45
14
42
20
AC radial fans backward curved blades
psF [Pa]
40
0
0
100
200 300 qv [m³/h]
400
197 230 260 274 6,5
10
500
500 85
Fan characteristic measured in full bell mouth with guard grill
Accessories
87
Fan with plate Type
Code
Sucking
R09P-2025A-4M-2516
On request
Blowing
R09P-2025P-4M-2516
On request
Weight (kg) Connection diagramS
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Fan without guard grill 0301-1-0026 0301-1-0002
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R09E-2025A-4M-2516
On request
Blowing
R09E-2025P-4M-2516
On request
Weight (kg)
79
AC Axial fans Paddle blades
250 mm
Diameter:
R09_-2525_-2M-3539
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
95/130 W
Rated current
0.44/0.58 A
Rated speed
2700/2950 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
65 °C
Sound power level A weighted
72/73 dB (A)
Condensator
2 µF/450 V
Connection
cable
Insulation class
155
Protection class
IP44
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Fan with guard grill Airflow Direction
Type
Code
Sucking
R09R-2525A-2M-3539
0309-4-0198
Blowing
R09R-2525P-2M-3539
On request
Weight (kg)
2.5
Aerodynamic characteristic 50 Hz
60 Hz
120 100 80
17
52
psF [Pa]
45
60 40
0
6,5
249 269 300 314
20
0
500
1000
1500
2000
qv [m³/h]
500 85
Fan characteristic measured in full bell mouth with guard grill
97
Fan with plate Airflow Direction
Type
Code
Sucking
R09P-2525A-2M-3539
On request
Blowing
R09P-2525P-2M-3539
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R09E-2525A-2M-3539
On request
Blowing
R09E-2525P-2M-3539
On request
80
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0026 0301-1-0002
Page 145 Page 134 Page 28
R09_-2525_-4M-2516
250 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V 50/60 Hz
Rated power input
AC axial fans Sickled blades
Frequency
35/44 W
Rated current
0.16/0.18 A
Rated speed
1430/1680 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70 °C 59/61 dB (A)
Condensator
1.5 µF/450 V
Connection
cable
Insulation class
155
Protection class
IP44
AC axial fans Plastic blades
Sound power level A weighted
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Fan with guard grill 50 Hz
Airflow Direction
60 Hz
60
Type
Code
Sucking
R09R-2525A-4M-2516
0309-4-0199
Blowing
R09R-2525P-4M-2516
0309-4-0217
Weight (kg) AC axial fans Paddle blades
Aerodynamic characteristic
2.1
45
30
11
42
AC radial fans backward curved blades
psF [Pa]
45
0
200
400 600 qv [m³/h]
800
1000
6,5
0
249 269 300 314
15
500 85
Fan characteristic measured in full bell mouth with guard grill
Accessories
87
Fan with plate Type
Code
Sucking
R09P-2525A-4M-2516
On request
Blowing
R09P-2525P-4M-2516
On request
Weight (kg) Connection diagramS
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Fan without guard grill 0301-1-0026 0301-1-0002
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R09E-2525A-4M-2516
On request
Blowing
R09E-2525P-4M-2516
On request
Weight (kg)
81
AC Axial fans Paddle blades
250 mm
Diameter:
R09_-2525_-6M-2515
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
36/41 W
Rated current
0.16/0.18 A
Rated speed
980/1160 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
55 °C
Sound power level A weighted
44/45 dB (A)
Condensator
1.5 µF/450 V
Connection
cable
Insulation class
155
Protection class
IP44
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Fan with guard grill Airflow Direction
Type
Code
Sucking
R09R-2525A-6M-2515
0309-4-0191
Blowing
R09R-2525P-6M-2515
0309-4-0218
Weight (kg)
Aerodynamic characteristic 50 Hz
60 Hz
40
2.1
30 11
42
psF [Pa]
45
20
0
6,5
249 269 300 314
10
0
200
400 qv [m³/h]
600
800
500 85
Fan characteristic measured in full bell mouth with guard grill
87
Fan with plate Airflow Direction
Type
Code
Sucking
R09P-2525A-6M-2515
On request
Blowing
R09P-2525P-6M-2515
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R09E-2525A-6M-2515
On request
Blowing
R09E-2525P-6M-2515
On request
82
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0026 0301-1-0002
Page 145 Page 134 Page 28
R09_-2528_-4M-2516
200 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V 50/60 Hz 40/52 W
Rated current
0.17/0.22 A
Rated speed
1360/1550 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70 °C
Sound power level A weighted
60/63 dB (A)
Condensator
1.5 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Rated power input
AC axial fans Sickled blades
Frequency
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Fan with guard grill 50 Hz
Airflow Direction
60 Hz
50
Type
Code
Sucking
R09R-2528A-4M-2516
0309-4-0213
Blowing
R09R-2528P-4M-2516
0309-4-0215
Weight (kg) AC axial fans Paddle blades
Aerodynamic characteristic
1.9
30
45
42 24
20
AC radial fans backward curved blades
psF [Pa]
40
0
200
400
600 800 qv [m³/h]
1000
1200
1400
6,5
0
249 269 300 314
10
Fan characteristic measured in short bell mouth with guard grill
Accessories
138
Fan with plate Type
Code
Sucking
R09P-2528A-4M-2516
On request
Blowing
R09P-2528P-4M-2516
On request
Weight (kg) Connection diagramS
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Fan without guard grill 0301-1-0026 0301-1-0002
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R09E-2528A-4M-2516
On request
Blowing
R09E-2528P-4M-2516
On request
Weight (kg)
83
AC Axial fans Paddle blades
300 mm
Diameter:
R09_-3028_-4M-3509
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
74/92 W
Rated current
0.34/0.4 A
Rated speed
1330/1470 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
50 °C
Sound power level A weighted
67/70 dB (A)
Condensator
2.5 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Fan with guard grill Airflow Direction
Type
Code
Sucking
R09R-3028A-4M-3509
0309-4-0100
Blowing
R09R-3028P-4M-3509
0309-4-0121
Weight (kg)
Aerodynamic characteristic 50 Hz
60 Hz
60
3.4
50 40 55 36
psF [Pa]
43
30 20
0
6,5
300 316 360 376
10
0
500
1000 1500 qv [m³/h]
2000
2500
Fan characteristic measured in short bell mouth with guard grill
148
Fan with plate Airflow Direction
Type
Code
Sucking
R09P-3028A-4M-3509
On request
Blowing
R09P-3028P-4M-3509
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R09E-3028A-4M-3509
On request
Blowing
R09E-3028P-4M-3509
On request
84
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0026 0301-1-0002
Page 145 Page 134 Page 28
R09_-3028_-4T-2513
300 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400/230 V 50/60 Hz
Rated power input
AC axial fans Sickled blades
Frequency
72/81 W 0,18/0,16/0,31/0,28 A
Rated speed
1300/1440 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
50 °C
Sound power level A weighted
66/69 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Rated current
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Fan with guard grill
50 Hz
Airflow Direction
60 Hz
60 50
Type
Code
Sucking
R09R-3028A-4T-2513
0309-4-0059
Blowing
R09R-3028P-4T-2513
0309-4-0035
Weight (kg) AC axial fans Paddle blades
Aerodynamic characteristic
3.0
psF [Pa]
40 30
45 36
43
AC radial fans backward curved blades
20
0
500
1000 1500 qv [m³/h]
2000
2500 300 316 360 376
0
6,5
10
Fan characteristic measured in short bell mouth with guard grill
Accessories
138
Fan with plate Type
Code
Sucking
R09P-3028A-4T-2513
On request
Blowing
R09P-3028P-4T-2513
On request
Weight (kg) Connection diagramS
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Fan without guard grill 0301-1-0049 0301-1-0049
Page 146 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R09E-3028A-4T-2513
On request
Blowing
R09E-3028P-4T-2513
On request
Weight (kg)
85
AC Axial fans Paddle blades
315 mm
Diameter:
R09_-3132_-4M-3509
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
68/117 W
Rated current
0.38/0.51 A
Rated speed
1340/1490 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
55/45 °C
Sound power level A weighted
68/72 dB (A)
Condensator
3.15 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Fan with guard grill Airflow Direction
Type
Code
Sucking
R09R-3132A-4M-3509
0309-4-0048
Blowing
R09R-3132P-4M-3509
0309-4-0075
Weight (kg)
Aerodynamic characteristic 50 Hz
60 Hz
70
3.5
60 50
33 24
psF [Pa]
65
40 30 20
0
6,5
312 336 380 398
10 0
500
1000 1500 qv [m³/h]
2000
2500
Fan characteristic measured in short bell mouth with guard grill
148
Fan with plate Airflow Direction
Type
Code
Sucking
R09P-3132A-4M-3509
On request
Blowing
R09P-3132P-4M-3509
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R09E-3132A-4M-3509
On request
Blowing
R09E-3132P-4M-3509
On request
86
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0026 0301-1-0002
Page 145 Page 134 Page 28
R09_-3132_-4T-3524
315 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
3~ 400/230 V
Frequency
50/60 Hz
Rated power input
80/102 W 0,20/0,34/0,19/0,33 A
Rated speed
1350/1500 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
65 °C
Sound power level A weighted
68/72 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Rated current
AC axial fans Sickled blades
Nominal voltage
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Fan with guard grill
50 Hz
Airflow Direction
60 Hz
70 60
Type
Code
Sucking
R09R-3132A-4T-3524
0309-4-0130
Blowing
R09R-3132P-4T-3524
0309-4-0091
Weight (kg) AC axial fans Paddle blades
Aerodynamic characteristic
4.0
psF [Pa]
50 40 65
30
33 24
AC radial fans backward curved blades
20
0
500
1000 1500 qv [m³/h]
2000
2500 312 336 380 398
0
6,5
10
Fan characteristic measured in short bell mouth with guard grill
Accessories
148
Fan with plate Type
Code
Sucking
R09P-3132A-4T-3524
On request
Blowing
R09P-3132P-4T-3524
On request
Weight (kg) Connection diagramS
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Fan without guard grill 0301-1-0049 0301-1-0049
Page 146 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R09E-3132A-4T-3524
On request
Blowing
R09E-3132P-4T-3524
On request
Weight (kg)
87
AC Axial fans Paddle blades
330 mm
Diameter:
R09_-3332_-4M-4240
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
130/170 W
Rated current
0.58/0.78 A
Rated speed
1330/1480 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
55 °C
Sound power level A weighted
70/72 dB (A)
Condensator
4 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Sucking Blowing
Overall efficiency
Type
Code
R09R-3332A-4M-4240 R09R-3332P-4M-4240
0309-4-0264 0309-4-0265
Weight (kg)
3.5
25.2 %
Measurement category
A
Efficiency category
static
Efficiency grade N
36.9
Variable speed drive
NO
Power input
143 W
Air flow 80
1478 m³/h
Pressure drop
31
91 Pa
Speed
1300 RPM
Specific ratio
1.00
6,5
330 356 415 432
Aerodynamic characteristic 50 Hz
60 Hz
ErP Data
75
psF [Pa]
60
155
Airflow Direction
Type
Sucking
R09P-3332A-4M-4240
On request
Blowing
R09P-3332P-4M-4240
On request
Code
Weight (kg)
Type
Code
Sucking
R09E-3332A-4M-4240
On request
Blowing
R09E-3332P-4M-4240
On request
0
0
500
1000
1500
2000
2500
3000
qv [m³/h] Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
Fan without guard grill
88
30 15
Fan with plate
Airflow Direction
45
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0043 0301-1-0044
Page 145 Page 134 Page 28
R09_-3532_-4M-4237
350 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V 50/60 Hz
Rated power input
130/165 W
Rated current
0.58/0.72 A
Rated speed
1280/1350 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70/65 °C 71/73 dB (A)
Condensator
4 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
AC axial fans Sickled blades
Frequency
ErP data according to EU regulation 327/2011:
Fan with guard grill
26.2 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
37.7
Sucking
R09R-3532A-4M-4237
0309-4-0108
Variable speed drive
NO
Blowing
R09R-3532P-4M-4237
0309-4-0221
Power input
149 W
Air flow
Type
Code
Weight (kg) AC axial fans Paddle blades
Overall efficiency
4.0
1889 m³/h
Pressure drop
78 Pa
Speed
61
44 37
1285 RPM 1.00
AC radial fans backward curved blades
Specific ratio
60 Hz
ErP Data
353 376 442 460
50 Hz 100
6,5
Aerodynamic characteristic
60 40 20 0
Accessories
155
Fan with plate 0
500
1000
1500 2000 qv [m³/h]
2500
3000
3500
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R09P-3532A-4M-4237
On request
Blowing
R09P-3532P-4M-4237
On request
Weight (kg) Connection diagramS
psF [Pa]
80
Fan without guard grill 0301-1-0043 0301-1-0044
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R09E-3532A-4M-4237
On request
Blowing
R09E-3532P-4M-4237
On request
Weight (kg)
89
AC Axial fans Paddle blades
350 mm
Diameter:
R09_-3532_-4T-4203
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400/230 V
Frequency
50/60 Hz
Rated power input
135/175 W
Rated current
0,31/0,54/0,32/0,55 A
Rated speed
1340/1460 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
40/55 °C
Sound power level A weighted
72/75 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011: Overall efficiency
Fan with guard grill Airflow Direction
Type
Sucking
Code
R09R-3532A-4T-4203
Blowing
25.4 %
Measurement category
R09R-3532P-4T-4203
0309-4-0222 0309-4-0223
Weight (kg)
4.0
A
Efficiency category
static
Efficiency grade N
36.6
Variable speed drive
NO
Power input
168 W
Air flow
2051 m³/h
Pressure drop 61
78 Pa
Speed
44 37
1327 RPM
Specific ratio
1.00
Aerodynamic characteristic 6,5
353 376 442 460
50 Hz
60 Hz
ErP Data
100
psF [Pa]
80 60 40
155
20
Fan with plate
0
Airflow Direction
Type
Code
Sucking
R09P-3532A-4T-4203
On request
Blowing
R09P-3532P-4T-4203
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R09E-3532A-4T-4203
On request
Blowing
R09E-3532P-4T-4203
On request
90
Weight (kg)
0
500
1000
1500 2000 qv [m³/h]
2500
3000
3500
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0049 0301-1-0049
Page 146 Page 134 Page 28
R11_-3530_-4M-3852
350 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V 50/60 Hz
Rated power input
175/210 W
Rated current
0.8/1.15 A
Rated speed
1410/1570 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
60/50 °C
AC axial fans Sickled blades
Frequency
Condensator
4 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
Compliant to
ErP data according to EU regulation 327/2011:
Fan with guard grill
29.0 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
40.2
Sucking
R11R-3530A-4M-3852
0311-4-0297
NO
Blowing
R11R-3530P-4M-3852
0311-4-0404
Variable speed drive Power input
170 W
Air flow
Type
Code
Weight (kg) AC axial fans Paddle blades
Overall efficiency
6.0
2012 m³/h
Pressure drop
93 Pa
Speed
84
1411 RPM 1.00
AC radial fans backward curved blades
Specific ratio
51 21
60 Hz
ErP Data
350 376 442 458
50 Hz 125
6,5
Aerodynamic characteristic
75
25 0
Accessories
188
50
Fan with plate 0
1000
2000 qv [m³/h]
3000
4000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R11P-3530A-4M-3852
On request
Blowing
R11P-3530P-4M-3852
On request
Weight (kg) Connection diagramS
psF [Pa]
100
Fan without guard grill 0301-1-0043 0301-1-0044
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R11E-3530A-4M-3852
On request
Blowing
R11E-3530P-4M-3852
On request
Weight (kg)
91
AC Axial fans Paddle blades
400 mm
Diameter:
R11_-4025_-4M-5137
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
170/205 W
Rated current
0.82/0.89 A
Rated speed
1370/1570 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70/65 °C
Sound power level A weighted
71/74 dB (A)
Condensator
6.3 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
Compliant to
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Overall efficiency
Type
Sucking
Code
R11R-4025A-4M-5137
Blowing
R11R-4025P-4M-5137
0311-4-0194 0311-4-0195
Weight (kg)
6.1
33.3 %
Measurement category
A
Efficiency category
static
Efficiency grade N
43.8
Variable speed drive
NO
Power input
219 W
Air flow
2552 m³/h
Pressure drop 84
25
62
109 Pa
Speed
1404 RPM
Specific ratio
1.00
9,5
Aerodynamic characteristic 395 423 455 476
50 Hz
60 Hz
ErP Data
90 75
psF [Pa]
60 200
45 30 15
Fan with plate Airflow Direction
Type
Code
Sucking
R11P-4025A-4M-5137
On request
Blowing
R11P-4025P-4M-5137
On request
Weight (kg)
Type
Code
Sucking
R11E-4025A-4M-5137
On request
Blowing
R11E-4025P-4M-5137
On request
92
0
1000
2000 3000 qv [m³/h]
4000
5000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
Fan without guard grill Airflow Direction
0
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
R11_-4030_-4M-5137
400 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V 200/265 W
Rated current
0.9/1.15 A
Rated speed
1345/1500 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
65/45 °C
Sound power level A weighted
72/76 dB (A)
Condensator
6.3 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Sickled blades
50/60 Hz
Rated power input
AC axial fans Plastic blades
Frequency
Compliant to
ErP data according to EU regulation 327/2011:
Fan with guard grill
32.1 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
42.5
Sucking
R11R-4030A-4M-5137
0311-4-0192
Variable speed drive
NO
Blowing
R11R-4030P-4M-5137
0311-4-0193
Power input
228 W
Air flow
Type
Code
Weight (kg) AC axial fans Paddle blades
Overall efficiency
6.1
3121 m³/h
Pressure drop
88 Pa
Speed
84
1375 RPM 1.00
AC radial fans backward curved blades
Specific ratio
62 31
60 Hz
ErP Data
395 423 455 476
50 Hz 90
9,5
Aerodynamic characteristic
75
45
200
Accessories
psF [Pa]
60
30 15
0
1000
2000 3000 qv [m³/h]
4000
5000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R11P-4030A-4M-5137
On request
Blowing
R11P-4030P-4M-5137
On request
Weight (kg) Connection diagramS
0
Fan with plate
Fan without guard grill 0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R11E-4030A-4M-5137
On request
Blowing
R11E-4030P-4M-5137
On request
Weight (kg)
93
AC Axial fans Paddle blades
400 mm
Diameter:
R11_-4035_-4M-5715
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50 Hz
Rated power input
245 W
Rated current
1.15 A
Rated speed
1320 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
50 °C
Sound power level A weighted
73 dB (A)
Condensator
6.3 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Sucking Blowing
Overall efficiency
Type
Code
R11R-4035A-4M-5715 R11R-4035P-4M-5715
0311-4-0028 0311-4-0047
Weight (kg)
6.3
26.5 %
Measurement category
A
Efficiency category
static
Efficiency grade N
36.2
Variable speed drive
NO
Power input
293 W
Air flow
3243 m³/h
Pressure drop 84
69 48
89 Pa
Speed
1324 RPM
Specific ratio
1.00
9,5
Aerodynamic characteristic 395 423 455 476
50 Hz
ErP Data
70 60
psF [Pa]
50
206
40 30 20 10
Fan with plate Airflow Direction
Type
Code
Sucking
R11P-4035A-4M-5715
On request
Blowing
R11P-4035P-4M-5715
On request
Weight (kg)
Type
Code
Sucking
R11E-4035A-4M-5715
On request
Blowing
R11E-4035P-4M-5715
On request
94
0
1000
2000 3000 qv [m³/h]
4000
5000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
Fan without guard grill Airflow Direction
0
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
R11_-4030_-4T2-3830
400 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V 50 Hz
Speed
AC axial fans Sickled blades
Frequency
high/low
Rated power input
195/130 W
Rated current
0.34/0.21 A
Rated speed
1320/1000 RPM
Min. ambient temperature
-30 °C 70/70 °C
Sound power level A weighted
73/66 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Max. ambient temperature
Compliant to
ErP data according to EU regulation 327/2011:
Fan with guard grill
31.3 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
41.8
Variable speed drive
NO
Power input
218 W
Air flow
Type
Code
Sucking
R11R-4030A-4T2-3830
0311-4-0034
Blowing
R11R-4030P-4T2-3830
0311-4-0042
Weight (kg) AC axial fans Paddle blades
Overall efficiency
5.7
2840 m³/h
Pressure drop
90 Pa
Speed
84
1332 RPM 1.00
AC radial fans backward curved blades
Specific ratio
50 42
Low speed
ErP Data
395 423 455 476
High speed 70
9,5
Aerodynamic characteristic
60
40 187
30
Accessories
psF [Pa]
50
20 10
Fan with plate 0
1000
2000 3000 qv [m³/h]
4000
5000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R11P-4030A-4T2-3830
On request
Blowing
R11P-4030P-4T2-3830
On request
Weight (kg) Connection diagramS
0
Fan without guard grill 0301-1-0048 0301-1-0048
Page 146 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R11E-4030A-4T2-3830
On request
Blowing
R11E-4030P-4T2-3830
On request
Weight (kg)
95
AC Axial fans Paddle blades
400 mm
Diameter:
R11_-4035_-4T2-5745
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
260/190 W
Rated current
0,60/0,30 A
Rated speed
1380/1160 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70/70 °C
Sound power level A weighted
75/71 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Sucking Blowing
Overall efficiency
Type
Code
R11R-4035A-4T2-5745 R11R-4035P-4T2-5745
0311-1-0159 0311-4-0049
Weight (kg)
6.3
29.1 %
Measurement category
A
Efficiency category
static
Efficiency grade N
38.8
Variable speed drive
NO
Power input
289 W
Air flow
3585 m³/h
Pressure drop 84
69 48
87 Pa
Speed
1382 RPM
Specific ratio
1.00
9,5
Aerodynamic characteristic 395 423 455 476
High speed
Low speed
ErP Data
80
psF [Pa]
60
206
40
20
Fan with plate Airflow Direction
Type
Code
Sucking
R11P-4035A-4T2-5745
On request
Blowing
R11P-4035P-4T2-5745
On request
Weight (kg)
Type
Code
Sucking
R11E-4035A-4T2-5745
On request
Blowing
R11E-4035P-4T2-5745
On request
96
0
1000
2000
3000 qv [m³/h]
4000
5000
6000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
Fan without guard grill Airflow Direction
0
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0048 0301-1-0048
Page 146 Page 134 Page 28
R11_-4225_-4M-5715
420 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V 235/320 W
Rated current
1,15/1,40 A
Rated speed
1400/1600 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
50/65 °C
Sound power level A weighted
70/73 dB (A)
Condensator
6.3 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Sickled blades
50/60 Hz
Rated power input
AC axial fans Plastic blades
Frequency
Compliant to
ErP data according to EU regulation 327/2011:
Fan with guard grill
31.0 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
41.2
Sucking
R11R-4225A-4M-5715
0311-4-0265
Variable speed drive
NO
Blowing
R11R-4225P-4M-5715
0311-4-0266
Power input
243 W
Air flow
Type
Code
Weight (kg) AC axial fans Paddle blades
Overall efficiency
6.3
3106 m³/h
Pressure drop
92 Pa
Speed
89
1372 RPM
63
1.00
AC radial fans backward curved blades
Specific ratio
31
60 Hz
ErP Data
418 455 490 520
50 Hz 80
9,5
Aerodynamic characteristic
40 206
Accessories
psF [Pa]
60
20
Fan with plate 0
1000
2000
3000 qv [m³/h]
4000
5000
6000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R11P-4225A-4M-5715
On request
Blowing
R11P-4225P-4M-5715
On request
Weight (kg) Connection diagramS
0
Fan without guard grill 0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R11E-4225A-4M-5715
On request
Blowing
R11E-4225P-4M-5715
On request
Weight (kg)
97
AC Axial fans Paddle blades
450 mm
Diameter:
R11_-4525_-4M-5765
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
260/370 W
Rated current
1.13/1.63 A
Rated speed
1310/1420 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
65/50 °C
Sound power level A weighted
72/75 dB (A)
Condensator
10 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
Compliant to
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Sucking Blowing
Overall efficiency
Type
Code
R11R-4525A-4M-5765 R11R-4525P-4M-5765
0311-4-0441 0311-4-0458
Weight (kg)
6.3
31.6 %
Measurement category
A
Efficiency category
static
Efficiency grade N
41.5
Variable speed drive
NO
Power input
275 W
Air flow 89
3501 m³/h
Pressure drop
63 31
92 Pa
Speed
1309 RPM
Specific ratio
1.00
50 Hz
9,5
445 480 520 540
Aerodynamic characteristic 60 Hz
ErP Data
100
psF [Pa]
80
206
Airflow Direction
Type
Code
Sucking
R11P-4525A-4M-5765
On request
Blowing
R11P-4525P-4M-5765
On request
Weight (kg)
Type
Code
Sucking
R11E-4525A-4M-5765
On request
Blowing
R11E-4525P-4M-5765
On request
0
0
1000
2000
3000 qv [m³/h]
4000
5000
6000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
Fan without guard grill
98
40 20
Fan with plate
Airflow Direction
60
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
R11_-4530_-4M-5749
450 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
1~ 230 V
Frequency
50 Hz
Rated power input
310 W
Rated current
1.4 A
Rated speed
1270 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
55 °C 74 dB (A)
Condensator
10 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
AC axial fans Sickled blades
Nominal voltage
ErP data according to EU regulation 327/2011:
Fan with guard grill
29.4 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
38.8 NO
Variable speed drive Power input
324 W
Air flow
Type
Code
Sucking
R11R-4530A-4M-5749
0311-4-0240
Blowing
R11R-4530P-4M-5749
0311-4-0270
Weight (kg) AC axial fans Paddle blades
Overall efficiency
6.3
3965 m³/h
Pressure drop
91 Pa
Speed
89
1291 RPM 1.00
AC radial fans backward curved blades
Specific ratio
63 37
ErP Data
445 480 520 540
50 Hz 100
9,5
Aerodynamic characteristic
60
20 0
Accessories
206
40
Fan with plate 0
1000
2000
3000 qv [m³/h]
4000
5000
6000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R11P-4530A-4M-5749
On request
Blowing
R11P-4530P-4M-5749
On request
Weight (kg) Connection diagramS
psF [Pa]
80
Fan without guard grill 0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R11E-4530A-4M-5749
On request
Blowing
R11E-4530P-4M-5749
On request
Weight (kg)
99
AC Axial fans Paddle blades
450 mm
Diameter:
R11_-4525_-4T-5136
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400/230
Frequency
50/60 Hz
Rated power input
230/310 W
Rated current
0,55/0,95/0,55/0,95 A
Rated speed
1335/1430 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70/70 °C
Sound power level A weighted
75/72 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Compliant to
Overall efficiency
Fan with guard grill Airflow Direction
Type
Sucking
Code
R11R-4525A-4T-5136
Blowing
33.7 %
Measurement category
R11R-4525P-4T-5136
0311-4-0117 0311-4-0082
Weight (kg)
6.3
A
Efficiency category
static
Efficiency grade N
43.5
Variable speed drive
NO
Power input
283 W
Air flow
3672 m³/h
Pressure drop 73
45
98 Pa
Speed
83
1358 RPM
Specific ratio
1.00
Aerodynamic characteristic 10
445 480 520 540
50 Hz
60 Hz
ErP Data
90 75
psF [Pa]
60 45 30
200
15
Fan with plate
0
Airflow Direction
Type
Code
Sucking
R11P-4525A-4T-5136
On request
Blowing
R11P-4525P-4T-5136
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R11E-4525A-4T-5136
On request
Blowing
R11E-4525P-4T-5136
On request
100
Weight (kg)
0
1000
2000
3000 qv [m³/h]
4000
5000
6000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0049 0301-1-0049
Page 146 Page 134 Page 28
R13_-4525_-4M-5009
450 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V 50/60 Hz
Rated power input
AC axial fans Sickled blades
Frequency
310/460 W
Rated current
1,4/2,0 A
Rated speed
1410/1630 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70/65 °C 8 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
74/79 dB (A)
Condensator
Compliant to
ErP data according to EU regulation 327/2011: Overall efficiency
Fan with guard grill
33.2 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
42.3
Variable speed drive
NO
Power input
365 W
Air flow
Type
Code
Sucking
R13R-4525A-4M-5009
0313-4-0003
Blowing
R13R-4525P-4M-5009
0313-4-0082
Weight (kg)
10.0
3703 m³/h
Pressure drop
124 Pa
Speed
96
1390 RPM
67 36
1.00
AC radial fans backward curved blades
Specific ratio
ErP Data
445 479 515 543
60 Hz
150
9,5
Aerodynamic characteristic 50 Hz
AC axial fans Paddle blades
Sound power level A weighted
125
75
Accessories
198
50 25 0
Fan with plate 0
1000
2000
3000 4000 qv [m³/h]
5000
6000
7000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R13P-4525A-4M-5009
On request
Blowing
R13P-4525P-4M-5009
On request
Weight (kg)
Fan without guard grill 0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-4525A-4M-5009
On request
Blowing
R13E-4525P-4M-5009
On request
Weight (kg)
101
Connection diagramS
psF [Pa]
100
AC Axial fans Paddle blades
450 mm
Diameter:
R13_-4530_-4M-7039
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
375/570 W
Rated current
1.7/2.5 A
Rated speed
1390/1570 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70/55 °C
Sound power level A weighted
76/81 dB (A)
Condensator
10 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
Compliant to
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Overall efficiency
Type
Sucking
Code
R13R-4530A-4M-7039
Blowing
R13R-4530P-4M-7039
0313-4-0178 0313-4-0166
Weight (kg)
12.1
32.5 %
Measurement category
A
Efficiency category
static
Efficiency grade N
41.2
Variable speed drive
NO
Power input
427 W
Air flow 96
44
4111 m³/h
Pressure drop
87
127 Pa
Speed
1377 RPM
Specific ratio
1.00
9,5
Aerodynamic characteristic 445 479 515 543
50 Hz
60 Hz
ErP Data
150 125
psF [Pa]
100
218
75 50 25
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-4530A-4M-7039
On request
Blowing
R13P-4530P-4M-7039
On request
Weight (kg)
Type
Code
Sucking
R13E-4530A-4M-7039
On request
Blowing
R13E-4530P-4M-7039
On request
102
0
1000
2000
3000 4000 qv [m³/h]
5000
6000
7000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
Fan without guard grill Airflow Direction
0
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0035 0301-1-0029
Page 146 Page 134 Page 28
R13_-4525_-4T-3529
450 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400/230 V 50/60 Hz 290/410 W
Rated current
0,81/1,40/0,81/1,40 A
Rated speed
1350/1530 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
40/65 °C
Sound power level A weighted
72/78 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Compliant to
33.0 %
Measurement category
Fan with guard grill
A
Efficiency category
static
Efficiency grade N
42.3
Airflow Direction
NO
Sucking
R13R-4525A-4T-3529
0313-4-0138
344 W
Blowing
R13R-4525P-4T-3529
0313-4-0059
Variable speed drive Power input Air flow
3489 m³/h
Code
Weight (kg)
8.4
123 Pa
Speed
1366 RPM
Specific ratio
96
1.00
52 36
AC radial fans backward curved blades
Pressure drop
Type
AC axial fans Paddle blades
Overall efficiency
AC axial fans Plastic blades
Rated power input
AC axial fans Sickled blades
Frequency
Aerodynamic characteristic 60 Hz
ErP Data 445 479 515 543
9,5
50 Hz 120 100
60 40
Accessories
183
20 0
0
1000
2000
3000 4000 qv [m³/h]
5000
6000
7000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-4525A-4T-3529
On request
Blowing
R13P-4525P-4T-3529
On request
Weight (kg)
Fan without guard grill 0301-1-0034 0301-1-0034
Page 147 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-4525A-4T-3529
On request
Blowing
R13E-4525P-4T-3529
On request
Weight (kg)
103
Connection diagramS
psF [Pa]
80
AC Axial fans Paddle blades
450 mm
Diameter:
R13_-4530_-4T2-3567
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
360/230 W
Rated current
0,70/0.39 A
Rated speed
1350/1100 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70 °C
Sound power level A weighted
78/71 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
Compliant to
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Sucking Blowing
Overall efficiency
Type
R13R-4530A-4T2-3567 R13R-4530P-4T2-3567
Code
0313-4-0291 On request
Weight (kg)
8.4
32.0 %
Measurement category
A
Efficiency category
static
Efficiency grade N
41.0
Variable speed drive
NO
Power input
384 W
Air flow 96
3904 m³/h
Pressure drop
52 44
116 Pa
Speed
1294 RPM
Specific ratio
1.00
9,5
445 479 515 543
Aerodynamic characteristic High speed
Low speed
ErP Data
105 90
psF [Pa]
75
183
60 45 30 15
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-4530A-4T2-3567
On request
Blowing
R13P-4530P-4T2-3567
On request
Weight (kg)
Type
Code
Sucking
R13E-4530A-4T2-3567
On request
Blowing
R13E-4530P-4T2-3567
On request
104
0
1000
2000
3000 4000 qv [m³/h]
5000
6000
7000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
Fan without guard grill Airflow Direction
0
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
R13_-4535_-4T2-5004
450 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V 50 Hz
Speed
AC axial fans Sickled blades
Frequency
high/low
Rated power input
465/330 W
Rated current
0.95/0.55 A
Rated speed
1360/1100 RPM
Min. ambient temperature
-30 °C 60 °C 80/73 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
ErP data according to EU regulation 327/2011: Overall efficiency
Fan with guard grill
28.6 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
36.8
Sucking
R13R-4535A-4T2-5004
0313-4-0004
NO
Blowing
R13R-4535P-4T2-5004
0313-4-0002
Variable speed drive Power input
509 W
Air flow
Type
Code
Weight (kg)
10.0
4820 m³/h
Pressure drop
114 Pa
Speed
96
1339 RPM
67 53
1.00
AC radial fans backward curved blades
Specific ratio
ErP Data
445 479 515 543
Low speed
9,5
Aerodynamic characteristic High speed 105 90 75 60 45
Accessories
198
30 15 0
Fan with plate 0
2000
4000 qv [m³/h]
6000
8000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R13P-4535A-4T2-5004
On request
Blowing
R13P-4535P-4T2-5004
On request
Weight (kg)
Fan without guard grill 0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-4535A-4T2-5004
On request
Blowing
R13E-4535P-4T2-5004
On request
Weight (kg)
105
Connection diagramS
psF [Pa]
AC axial fans Paddle blades
Max. ambient temperature
AC Axial fans Paddle blades
450 mm
Diameter:
R13_-4535_-6M-5027
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
195/240 W
Rated current
1,0/1.05 A
Rated speed
910/1040 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
50/50 °C
Sound power level A weighted
69/73 dB (A)
Condensator
6.3 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
Aerodynamic characteristic
Fan with guard grill Airflow Direction
Type
Code
R13R-4535A-6M-5027
0313-4-045
Blowing
R13R-4535P-6M-5027
0313-4-0201
50 Hz
Weight (kg)
60 Hz
60 50
10.0
40 psF [Pa]
Sucking
96
50/60 Hz
Rated power input
67 53
30 20 10
0
1000
2000
445 479 515 543
9,5
0
3000 qv [m³/h]
4000
5000
6000
Fan characteristic measured in short bell mouth with guard grill
198
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-4535A-6M-5027
On request
Blowing
R13P-4535P-6M-5027
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R13E-4535A-6M-5027
On request
Blowing
R13E-4535P-6M-5027
On request
106
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
R13_-4530_-6T2-3525
450 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V 50 Hz
Speed
AC axial fans Sickled blades
Frequency
high/low
Rated power input
120/85 W
Rated current
0,28/0,14 A
Rated speed
915/770 RPM
Min. ambient temperature
-30 °C 70/70 °C
Sound power level A weighted
68/63 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Max. ambient temperature
Compliant to
ErP data according to EU regulation 327/2011:
Fan with guard grill
28.5 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
40.1 NO
Variable speed drive Power input
146 W
Air flow
Type
Code
Sucking
R13R-4530A-6T2-3525
0313-4-0037
Blowing
R13R-4530P-6T2-3525
0313-4-0112
Weight (kg) AC axial fans Paddle blades
Overall efficiency
8.4
2851 m³/h
Pressure drop
54 Pa
Speed
96
909 RPM 1.00
AC radial fans backward curved blades
Specific ratio
52 44
Low speed
ErP Data
445 479 515 543
High speed 60
9,5
Aerodynamic characteristic
50
30 Accessories
183
20 10 0
Fan with plate 0
1000
2000
3000
4000
5000
qv [m³/h] Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R13P-4530A-6T2-3525
On request
Blowing
R13P-4530P-6T2-3525
On request
Weight (kg)
Fan without guard grill 0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-4530A-6T2-3525
On request
Blowing
R13E-4530P-6T2-3525
On request
Weight (kg)
107
Connection diagramS
psF [Pa]
40
AC Axial fans Paddle blades
450 mm
Diameter:
R13_-4535_-6T2-3526
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
160/110 W
Rated current
0.37/0.19 A
Rated speed
915/765 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70/70 °C
Sound power level A weighted
69/64 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Sucking Blowing
Overall efficiency
Type
R13R-4535A-6T2-3526 R13R-4535P-6T2-3526
Code
0313-4-0143 On request
Weight (kg)
8.4
25.7 %
Measurement category
A
Efficiency category
static
Efficiency grade N
36.5
Variable speed drive
NO
Power input
196 W
Air flow
3032 m³/h
Pressure drop 96
53
63 Pa
Speed
906 RPM
Specific ratio
1.00
9,5
Aerodynamic characteristic 445 479 515 543
High speed
Low speed
ErP Data
60 50
psF [Pa]
40 184
30 20 10
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-4535A-6T2-3526
On request
Blowing
R13P-4535P-6T2-3526
On request
Weight (kg)
Type
Code
Sucking
R13E-4535A-6T2-3526
On request
Blowing
R13E-4535P-6T2-3526
On request
108
0
1000
2000 3000 qv [m³/h]
4000
5000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
Fan without guard grill Airflow Direction
0
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
R13_-5025_-4M-5009
500 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
1~ 230 V
Frequency
50 Hz
Rated power input
440 W
Rated current
2,0 A
Rated speed
1340 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70 °C 8 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
78 dB (A)
Condensator
Compliant to
ErP data according to EU regulation 327/2011: Overall efficiency
Fan with guard grill
32.6 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
40.9
Sucking
R13R-5025A-4M-5009
0313-4-0073
NO
Blowing
R13R-5025P-4M-5009
0313-4-0222
Variable speed drive Power input
488 W
Air flow
Type
Code
Weight (kg)
10.4
4844 m³/h
Pressure drop
122 Pa
Speed
96
67 36
1309 RPM 1.00
AC radial fans backward curved blades
Specific ratio
497 522 565 589
ErP Data
105
9,5
Aerodynamic characteristic 50 Hz 90 75 60 45
Accessories
198
30 15 0
Fan with plate 0
2000
4000 qv [m³/h]
6000
8000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R13P-5025A-4M-5009
On request
Blowing
R13P-5025P-4M-5009
On request
Weight (kg)
Fan without guard grill 0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-5025A-4M-5009
On request
Blowing
R13E-5025P-4M-5009
On request
Weight (kg)
109
Connection diagramS
psF [Pa]
AC axial fans Paddle blades
Sound power level A weighted
AC axial fans Sickled blades
Nominal voltage
AC Axial fans Paddle blades
500 mm
Diameter:
R13_-5030_-4M-7012
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50 Hz
Rated power input
550 W
Rated current
2.5 A
Rated speed
1300 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70 °C
Sound power level A weighted
82 dB (A)
Condensator
10 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Overall efficiency
Type
Sucking
R13R-5030A-4M-7012
Blowing
R13R-5030P-4M-7012
Code
0313-4-0011 0313-4-0062
Weight (kg)
12.5
29.1 %
Measurement category
A
Efficiency category
static
Efficiency grade N
36.8
Variable speed drive
NO
Power input
599 W
Air flow 96
44
5724 m³/h
Pressure drop
87
114 Pa
Speed
1273 RPM
Specific ratio
1.00
9,5
497 522 565 589
Aerodynamic characteristic 50 Hz
ErP Data
120 100
psF [Pa]
80
218
60 40 20
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-5030A-4M-7012
On request
Blowing
R13P-5030P-4M-7012
On request
Weight (kg)
Type
Code
Sucking
R13E-5030A-4M-7012
On request
Blowing
R13E-5030P-4M-7012
On request
110
0
2000
4000
6000 qv [m³/h]
8000
10000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
Fan without guard grill Airflow Direction
0
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
R13_-5025_-4T2-5004
500 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V 50 Hz
Speed
AC axial fans Sickled blades
Frequency
high/low
Rated power input
455/325 W
Rated current
0.95/0.53 A
Rated speed
1380/1150 RPM
Min. ambient temperature
-30 °C 78/74 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
50/50 °C
Sound power level A weighted
Compliant to
ErP data according to EU regulation 327/2011: Overall efficiency
Fan with guard grill
33.5 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
41.9
Sucking
R13R-5025A-4T2-5004
0313-4-0137
Variable speed drive
NO
Blowing
R13R-5025P-4T2-5004
0313-4-0158
Power input
470 W
Air flow
Type
Code
Weight (kg)
10.4
4894 m³/h
Pressure drop
120 Pa
Speed
96
67 36
1368 RPM 1.00
AC radial fans backward curved blades
Specific ratio
ErP Data
497 522 565 589
Low speed
105
9,5
Aerodynamic characteristic High speed 90 75 60 45
Accessories
198
30 15 0
Fan with plate 0
2000
4000 qv [m³/h]
6000
8000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R13P-5025A-4T2-5004
On request
Blowing
R13P-5025P-4T2-5004
On request
Weight (kg)
Fan without guard grill 0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-5025A-4T2-5004
On request
Blowing
R13E-5025P-4T2-5004
On request
Weight (kg)
111
Connection diagramS
psF [Pa]
AC axial fans Paddle blades
Max. ambient temperature
AC Axial fans Paddle blades
500 mm
Diameter:
R13_-5030_-4T2-7002
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
560/410 W
Rated current
1.25/0,70 A
Rated speed
1380/1170 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70/70 °C
Sound power level A weighted
81/75 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
Compliant to
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Overall efficiency
Type
Sucking
R13R-5030A-4T2-7002
Blowing
R13R-5030P-4T2-7002
Code
0313-4-0006 0313-4-0097
Weight (kg)
12.5
33.6 %
Measurement category
A
Efficiency category
static
Efficiency grade N
41.1
Variable speed drive
NO
Power input
647 W
Air flow 96
44
5759 m³/h
Pressure drop
87
141 Pa
Speed
1365 RPM
Specific ratio
1.00
9,5
497 522 565 589
Aerodynamic characteristic High speed
Low speed
ErP Data
150 125
psF [Pa]
100
218
75 50 25
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-5030A-4T2-7002
On request
Blowing
R13P-5030P-4T2-7002
On request
Weight (kg)
Type
Code
Sucking
R13E-5030A-4T2-7002
On request
Blowing
R13E-5030P-4T2-7002
On request
112
0
2000
4000
6000 qv [m³/h]
8000
10000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
Fan without guard grill Airflow Direction
0
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
R13_-5035_-4T2-7002
500 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V 50 Hz
Speed
AC axial fans Sickled blades
Frequency
high/low
Rated power input
695/480 W
Rated current
1,30/0.78 A
Rated speed
1340/1070 RPM
Min. ambient temperature
-30 °C 81/75 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
60/60 °C
Sound power level A weighted
ErP data according to EU regulation 327/2011: Overall efficiency
Fan with guard grill
29.1 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
36.1 NO
Variable speed drive Power input
769 W
Air flow
Type
Code
Sucking
R13R-5035A-4T2-7002
0313-4-0005
Blowing
R13R-5035P-4T2-7002
0313-4-0249
Weight (kg)
12.5
6442 m³/h
Pressure drop
131 Pa
Speed
96
87 53
1324 RPM 1.00
AC radial fans backward curved blades
Specific ratio
ErP Data
497 522 565 589
Low speed
150
9,5
Aerodynamic characteristic High speed
AC axial fans Paddle blades
Max. ambient temperature
125
75
25 0
Accessories
218
50
Fan with plate 0
2000
4000
6000
8000
10000
qv [m³/h] Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R13P-5035A-4T2-7002
On request
Blowing
R13P-5035P-4T2-7002
On request
Weight (kg)
Fan without guard grill 0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-5035A-4T2-7002
On request
Blowing
R13E-5035P-4T2-7002
On request
Weight (kg)
113
Connection diagramS
psF [Pa]
100
AC Axial fans Paddle blades
500 mm
Diameter:
R13_-5025_-6M-7099
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50/60 Hz
Rated power input
230/300 W
Rated current
1,00/1.42 A
Rated speed
925/1050 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70/70 °C
Sound power level A weighted
79/82 dB (A)
Condensator
10 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
Compliant to
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Overall efficiency
Type
Sucking
R13R-5025A-6M-7099
Blowing
R13R-5025P-6M-7099
Code
0313-4-0425 On request
Weight (kg)
14.0
29.9 %
Measurement category
A
Efficiency category
static
Efficiency grade N
40.3
Variable speed drive
NO
Power input
229 W
Air flow 96
3681 m³/h
Pressure drop
87 27
70 Pa
Speed
924 RPM
Specific ratio
1.00
9,5
497 522 565 589
Aerodynamic characteristic 50 Hz
60 Hz
ErP Data
90 75
psF [Pa]
60
218
45 30 15
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-5025A-6M-7099
On request
Blowing
R13P-5025P-6M-7099
On request
Weight (kg)
Type
Code
Sucking
R13E-5025A-6M-7099
On request
Blowing
R13E-5025P-6M-7099
On request
114
0
1000
2000
3000 qv [m³/h]
4000
5000
6000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
Fan without guard grill Airflow Direction
0
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
R13_-5035_-6T2-5016
500 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V 50 Hz
Speed
AC axial fans Sickled blades
Frequency
high/low
Rated power input
250/185 W
Rated current
0.65/0.32 A
Rated speed
930/800 RPM
Min. ambient temperature
-30 °C 65/65 °C 73/67 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
ErP data according to EU regulation 327/2011: Overall efficiency
Fan with guard grill
26.4 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
36.0
Sucking
R13R-5035A-6T2-5016
0313-4-0127
NO
Blowing
R13R-5035P-6T2-5016
0313-4-0089
Variable speed drive Power input
306 W
Air flow
Type
Code
Weight (kg)
10.4
4378 m³/h
Pressure drop
68 Pa
Speed
96
930 RPM
67 53
1.00
AC radial fans backward curved blades
Specific ratio
ErP Data
497 522 565 589
Low speed
9,5
Aerodynamic characteristic High speed
AC axial fans Paddle blades
Max. ambient temperature
90 75
45 Accessories
198
30 15 0
Fan with plate 0
2000
4000
6000
8000
qv [m³/h] Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R13P-5035A-6T2-5016
On request
Blowing
R13P-5035P-6T2-5016
On request
Weight (kg)
Fan without guard grill 0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-5035A-6T2-5016
On request
Blowing
R13E-5035P-6T2-5016
On request
Weight (kg)
115
Connection diagramS
psF [Pa]
60
AC Axial fans Paddle blades
560 mm
Diameter:
R13_-5625_-4T2-7002
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
670/450 W
Rated current
1,30/0.73 A
Rated speed
1360/1130 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
65/65 °C
Sound power level A weighted
83/76 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
Compliant to
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Type
Sucking
R13R-5625A-4T2-7002
Blowing
R13R-5625P-4T2-7002
Overall efficiency Code
0313-4-0001 0313-4-0052
Weight (kg)
14.0
36.7 %
Measurement category
A
Efficiency category
static
Efficiency grade N
44.1
Variable speed drive
NO
Power input
682 W
Air flow 98
31
7223 m³/h
Pressure drop
82
130 Pa
Speed
1343 RPM
Specific ratio
1.00
10,5
552 644 700 727
Aerodynamic characteristic High speed
Low speed
ErP Data
140 120
psF [Pa]
100
218
80 60 40 20
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-5625A-4T2-7002
On request
Blowing
R13P-5625P-4T2-7002
On request
Weight (kg)
Type
Code
Sucking
R13E-5625A-4T2-7002
On request
Blowing
R13E-5625P-4T2-7002
On request
116
0
2000
4000 6000 qv [m³/h]
8000
10000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
Fan without guard grill Airflow Direction
0
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
R13_-5625_-6M-X093
560 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
1~ 230 V
Frequency
50 Hz
Rated power input
330 W
Rated current
1.5 A
Rated speed
845 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70 °C 6.3 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
73 dB (A)
Condensator
Compliant to
ErP data according to EU regulation 327/2011: Overall efficiency
Fan with guard grill
32.7 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
42.5
Variable speed drive
NO
Power input
282 W
Air flow
Type
Code
Sucking
R13R-5625A-6M-X093
0313-4-0415
Blowing
R13R-5625P-6M-X093
On request
Weight (kg)
16.0
4468 m³/h
Pressure drop
77 Pa
Speed
98
891 RPM
112
1.00
AC radial fans backward curved blades
Specific ratio
22
ErP Data
552 644 700 727
50 Hz
10,5
Aerodynamic characteristic 90
AC axial fans Paddle blades
Sound power level A weighted
AC axial fans Sickled blades
Nominal voltage
75
45
15 0
Accessories
248
30
Fan with plate 0
2000
4000 qv [m³/h]
6000
8000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R13P-5625A-6M-X093
On request
Blowing
R13P-5625P-6M-X093
On request
Weight (kg)
Fan without guard grill 0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-5625A-6M-X093
On request
Blowing
R13E-5625P-6M-X093
On request
Weight (kg)
117
Connection diagramS
psF [Pa]
60
AC Axial fans Paddle blades
560 mm
Diameter:
R13_-5630_-6T2-5016
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V
Frequency
50 Hz
Speed
high/low
Rated power input
305/210 W
Rated current
0,70/0.36 A
Rated speed
920/780 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
60/60 °C
Sound power level A weighted
72/68 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Sucking Blowing
Type
R13R-5630A-6T2-5016 R13R-5630P-6T2-5016
Overall efficiency Code
0313-4-0029 0313-4-0080
Weight (kg)
11.9
30.1 %
Measurement category
A
Efficiency category
static
Efficiency grade N
39.3
Variable speed drive
NO
Power input
355 W
Air flow 98
5219 m³/h
Pressure drop
62 39
77 Pa
Speed
908 RPM
Specific ratio
1.00
10,5
552 644 700 727
Aerodynamic characteristic High speed
Low speed
ErP Data
70 60
psF [Pa]
50
198
40 30 20 10
Fan with plate Airflow Direction
Type
Sucking
R13P-5630A-6T2-5016
On request
Blowing
R13P-5630P-6T2-5016
On request
Code
Weight (kg)
Type
Code
Sucking
R13E-5630A-6T2-5016
On request
Blowing
R13E-5630P-6T2-5016
On request
118
0
2000
4000
6000
8000
10000
qv [m³/h] Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
Fan without guard grill Airflow Direction
0
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
R13_-5635_-6T2-7021
560 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V 50 Hz
Speed
AC axial fans Sickled blades
Frequency
high/low
Rated power input
345/215 W
Rated current
0.63/0.36 A
Rated speed
870/660 RPM
Min. ambient temperature
-30 °C 74/67 dB (A)
Connection
terminal box 155
Protection class
IP54
Aerodynamic characteristic
psF [Pa]
High speed
Fan with guard grill
Low speed
70
Airflow Direction
60 50
Type
Code
Sucking
R13R-5635A-6T2-7021
0313-4-0065
Blowing
R13R-5635P-6T2-7021
0313-4-0079
Weight (kg)
14.0
40 30
98
82 48
20
2000
4000
6000
8000
Fan characteristic measured in short bell mouth with guard grill
Accessories
552 644 700 727
qv [m³/h]
10,5
0
AC radial fans backward curved blades
10 0
218
Fan with plate
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R13P-5635A-6T2-7021
On request
Blowing
R13P-5635P-6T2-7021
On request
Weight (kg)
Fan without guard grill 0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
Airflow Direction
AC axial fans Paddle blades
Insulation class
AC axial fans Plastic blades
70/70 °C
Sound power level A weighted
Type
Code
Sucking
R13E-5635A-6T2-7021
On request
Blowing
R13E-5635P-6T2-7021
On request
Weight (kg)
119
Connection diagramS
Max. ambient temperature
AC Axial fans Paddle blades
630 mm
Diameter:
R13_-6325_-6M-7019
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50 Hz
Rated power input
400 W
Rated current
1.8 A
Rated speed
925 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
50 °C
Sound power level A weighted
70 dB (A)
Condensator
12.5 µF/450 V
Connection
terminal box
Insulation class
155
Protection class
IP54
ErP data according to EU regulation 327/2011:
Fan with guard grill Airflow Direction
Overall efficiency
Type
Sucking
R13R-6325A-6M-7019
Blowing
R13R-6325P-6M-7019
Code
0313-4-0091 0313-4-0105
Weight (kg)
14.6
29.7 %
Measurement category
A
Efficiency category
static
Efficiency grade N
38.3
Variable speed drive
NO
Power input
434 W
Air flow 96
36
6714 m³/h
Pressure drop
87
73 Pa
Speed
879 RPM
Specific ratio
1.00
50 Hz
10
627 689 750 784
Aerodynamic characteristic ErP Data
90 75
psF [Pa]
60
218
45 30 15
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-6325A-6M-7019
On request
Blowing
R13P-6325P-6M-7019
On request
Weight (kg)
Type
Code
Sucking
R13E-6325A-6M-7019
On request
Blowing
R13E-6325P-6M-7019
On request
120
0
2000
4000 6000 qv [m³/h]
8000
10000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
Fan without guard grill Airflow Direction
0
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
R13_-6330_-6T2-7021
630 mm
Diameter:
EC axial fans
AC Axial fans Paddle blades
Nominal data according to standard EN 60335: Phase
3~
Nominal voltage
400 V 50 Hz
Speed
AC axial fans Sickled blades
Frequency
high/low
Rated power input
390/225 W
Rated current
0,70/0.38 A
Rated speed
840/590 RPM
Min. ambient temperature
-30 °C 70/70 °C 78/69 dB (A)
Connection
terminal box
Insulation class
155
Protection class
IP54
AC axial fans Plastic blades
Sound power level A weighted
ErP data according to EU regulation 327/2011: Overall efficiency
Fan with guard grill
28.0 %
Measurement category
A
Efficiency category
static
Airflow Direction
Efficiency grade N
36.5 NO
Variable speed drive Power input
459 W
Air flow
Type
Code
Sucking
R13R-6330A-6T2-7021
0313-4-0050
Blowing
R13R-6330P-6T2-7021
0313-4-0048
Weight (kg)
14.6
7573 m³/h
Pressure drop
63 Pa
Speed
96
830 RPM
87 44
1.00
AC radial fans backward curved blades
Specific ratio
ErP Data
627 689 750 784
Low speed
70
10
Aerodynamic characteristic High speed 60 50 40 30
Accessories
218
20 10 0
Fan with plate 0
2000
4000
6000 qv [m³/h]
8000
10000
12000
Fan characteristic measured in short bell mouth with guard grillErP characteristic measured in full bell mouth without guard grill
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
Airflow Direction
Type
Code
Sucking
R13P-6330A-6T2-7021
On request
Blowing
R13P-6330P-6T2-7021
On request
Weight (kg)
Fan without guard grill 0301-1-0033 0301-1-0033
Page 147 Page 134 Page 28
Airflow Direction
Type
Code
Sucking
R13E-6330A-6T2-7021
On request
Blowing
R13E-6330P-6T2-7021
On request
Weight (kg)
121
Connection diagramS
psF [Pa]
AC axial fans Paddle blades
Max. ambient temperature
AC Axial fans Paddle blades
630 mm
Diameter:
R13_-6335_-8M-7049
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50 Hz
Rated power input
265 W
Rated current
1.2 A
Rated speed
610 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
70 °C
Sound power level A weighted
Type
Code
Connection
terminal box
Insulation class
155
Protection class
IP54
R13R-6335A-8M-7049
0313-4-0231
Blowing
R13R-6335P-8M-7049
0313-4-0234
50 Hz
Weight (kg)
40
14.6
30 psF [Pa]
Sucking
96
8 µF/450 V
Aerodynamic characteristic
Fan with guard grill Airflow Direction
70 dB (A)
Condensator
87 53
20
10
0
2000
10
627 689 750 784
0
4000 qv [m³/h]
6000
8000
Fan characteristic measured in short bell mouth with guard grill
218
Fan with plate Airflow Direction
Type
Code
Sucking
R13P-6335A-8M-7049
On request
Blowing
R13P-6335P-8M-7049
On request
Weight (kg)
Fan without guard grill Airflow Direction
Type
Code
Sucking
R13E-6335A-8M-7049
On request
Blowing
R13E-6335P-8M-7049
On request
122
Weight (kg)
General notes Connection diagram: Sucking Blowing Accessories Compliant to standards
0301-1-0044 0301-1-0043
Page 145 Page 134 Page 28
Connection diagramS
Accessories
AC radial fans backward curved blades
AC axial fans Paddle blades
AC axial fans Plastic blades
AC axial fans Sickled blades
EC axial fans
AC Axial fans Paddle blades
123
05 AC Radial fans Backward curved blades
124
AC axial fans Paddle blades
AC axial fans Plastic blades
AC axial fans Sickled blades
EC axial fans
AC Radial fans Backward curved blades
AC radial fans backward curved blades
AC Radial fans Backward curved blades
Connection diagramS
Accessories
XXX Arciis erchic temolor empeles nam, quo tectorehenem fuga. Nam as simagniscia aut repelist quam sa que occae. Nemporionse volum none sam, sequae natur sus etur, nihil ipis aut es seque nations ecescit voluptatent ma nos aut ex et volorepedis et aut ut lamus et porem escit, earum.
125
AC Radial fans Backward curved blades
126
AC Radial fans Backward curved blades
AC axial fans Sickled blades
EC axial fans
Radial fans with induction (AC) motors Plastic wheels
AC axial fans Plastic blades
Diameter: 190 mm
Steel wheels
AC axial fans Paddle blades
Diameters: 220-250 mm
Steel impellers
AC radial fans backward curved blades
Diameters: 150-180 mm
Example of type key:
R09T-1945D-2M2-1511 R09 External rotor motor type (R09)
Accessories
T Blade type (T ‒ backward curved, C ‒ forward curved) 19 Fan diameter x 10 (exact diameters are stated in drawings) 45 Balde width D Direction of rotation
Connection diagramS
2 Number of motor poles M Number of phases (M ‒ single phase, T ‒ three phase) 2 Number of motor speed 15 Motor steck height 11 Version of electrical construction
127
Diameter: Diameter:
190 mm
AC Radial fans Backward curved blades
R09_-1945D-2M-1511 Nominal data according to standard EN 60335: Phase
1~ 230 V
Nominal voltage
50/60 Hz
Frequency Rated power input
190 mm
Diameter:
Rated current
50/63 W
R09_-1945D-2M-1511
0,21/0,27 A
2400/2530 RPM
Rated speed Min. ambient temperature Nominal data according to standard EN 60335: Max. ambient temperature Phase Sound power level A weighted Nominal voltage Condensator Frequency Connection Rated power input Insulation class Rated current Protection Rated speedclass
-30 °C 50/50 °C 1~ 60/62 dB (A) 230 V 2 µF/450 V 50/60 Hz cable 50/63 W 155 0.21/0.27 A IP44 RPM 2400/2530
Min. ambient temperature
-30 °C
Max. temperatureto EU regulation 327/2011: 50/50 °C ErPambient data according Sound level A weighted Is notpower subject to the EU regulation 327/2011 Condensator Power input lower than 125 W
60/62 dB (A) 2 μF/450 V
Connection
Code
Type R09T-1945D-2M-1511
Weight [kg]
0309-4-0190
1,4
cable
Insulation class
155
Protection class
IP44
ErP data according to EU regulation 327/2011:
Type
Code
Weight (kg)
R09T-1945D-2M-1511
0309-4-0079
1.4
Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
50 Hz
60 Hz
400 350 300
60 46
psF [Pa]
12
250 200 150
134 190
100 50 0
100
200 300 qv [m³/h]
400
500
500 85
0
70
4xM4/90°
General notes: Connection diagram:
General notes Connection diagram: 128
0301-1-0002
0301-1-0002
Page ???
Page 145
R09_-2250D-2M-3510 Phase
1~
Nominal voltage
230 V
Frequency
50 Hz 98 W
R09_-2250D-2M-3510
2450 RPM
Rated speed
-30 °C
Min. ambient temperature
50 °C 1~ 70 dB (A) 230 V 3,15 µF/450 V 50 Hz cable 98 W 155 0.42 A IP44RPM 2450
Min. ambient temperature Max. ErPambient datatemperature according
-30 °C °C to EU regulation 50 327/2011:
Sound power level A weighted Is not subject to the EU regulation 327/2011 Condensator Power input lower than 125 W Connection
70 dB (A) 3.15 μF/450 V cable
Insulation class
155
Protection class
IP44
ErP data according to EU regulation 327/2011: Is not subject to the EU regulation 327/2011. Power input lower than 125 W. Type
Code
Weight (kg)
R09T-2250D-2M-3510
0309-4-0066
2.5
50 Hz 600 500 52
76
AC radial fans backward curved blades
15
400 psF [Pa]
300
153 227
200 100 0
0
200
400 600 qv [m³/h]
800
1000 500 85
4xM4/90°
Accessories
90
General notes: Connection diagram:
General notes Connection diagram:
0301-1-0002
Page ??? Connection diagramS
2,5
AC axial fans Sickled blades
Nominal data according to standard EN 60335: Max. ambient temperature Phase Sound power level A weighted Nominal voltage Condensator Frequency Connection Rated power input Insulation class Rated current Protection Rated speedclass
ght [kg]
225 mm
Diameter:
0,42 A
AC axial fans Plastic blades
Rated power input Rated current
EC axial fans
AC Radial fans Backward curved blades
Nominal data according to standard EN 60335:
AC axial fans Paddle blades
5 mm
0301-1-0002
Page 145 129
Diameter: Diameter:
250 mm
AC Radial fans Backward curved blades
R09_-2540D-2M-3510 Nominal data according to standard EN 60335: Phase Nominal voltage
230 V
Frequency
50 Hz
Rated power input
250 mm
Diameter:
1~
Rated current
120 W
R09_-2540D-2M-3510
0,52 A
2350 RPM
Rated speed
-30 °C
Min. ambient temperature Nominal data according to standard EN 60335: Max. ambient temperature Phase Sound power level A weighted Nominal voltage Condensator Frequency Connection Rated power input Insulation class Rated current Protection Rated speedclass
50 °C 1~(A) 72 dB
230 V 4 µF/450 V 50 Hz cable 120 W 155 0.52 A IP44 2350 RPM
Min. ambient temperature
-30 °C
Max. ambient temperature
50 °C
Sound power level A weighted
Code
Type R09T-2540D-2M-3510
Weight [kg]
0309-4-0025
2,6
Type
Code
Weight (kg)
R09T-2540D-2M-3510
0309-4-0025
2.6
72 dB (A)
Condensator
4 μF/450 V
Connection
cable
Insulation class
155
Protection class
IP44
50 Hz 600 500 42
69
400 psF [Pa]
15
300 200
172 250
100
0
200
400
600 qv [m³/h]
800
1000
1200
600 85
0
90
4xM4/90°
General notes: Connection diagram:
General notes Connection diagram: 130
0301-1-0002
0301-1-0002
Page ???
Page 145
R09_-2540D-4M-2502 AC Radial fans Backward curved blades
Nominal data according to standard EN 60335: Phase
1~ 230 V
Nominal voltage
43/50 W
R09_-2540D-4M-2502
1380/1600 RPM
Rated speed
-30 °C
Min. ambient temperature Nominal data according to standard EN 60335: Max. ambient temperature Phase Sound power level A weighted Nominal voltage Condensator Frequency Connection Rated power input Insulation class Rated current Protection Rated speedclass
45/50 °C 65/681~dB (A)
230 V 1,5 µF/450 V 50/60 Hz cable 43/50 W 155 0.20/0.21 A IP44 RPM 1380/1600
Min. ambient temperature
-30 °C
ErP datatemperature according Max. ambient
Sound level A weighted Is notpower subject to the EU regulation 327/2011
65/68 dB (A)
Condensator Power input lower than 125 W Connection
1.5 μF/450 V
Insulation class
155
Protection class
IP44
AC axial fans Plastic blades
cable
ErP data according to EU regulation 327/2011: Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
50 Hz
Type
Code
Weight (kg)
R09T-2540D-4M-2502
0309-4-0065
2.1
60 Hz
250 200 150
42
69
AC radial fans backward curved blades
15
100
0
172 250
50
0
200
400
600
800
qv [m³/h]
600 85
4xM4/90°
Accessories
80
General notes: Connection diagram:
General notes Connection diagram:
0301-1-0002
Page ??? Connection diagramS
2,1
to EU regulation 327/2011: 45/50 °C
psF [Pa]
ight [kg]
250 mm
Diameter:
0,20/0,21 A
AC axial fans Sickled blades
Rated power input Rated current
EC axial fans
50/60 Hz
Frequency
AC axial fans Paddle blades
0 mm
0301-1-0002
Page 145 131
AC Radial fans Backward curved blades
150 mm
Diameter:
R09X-2M-1533
Nominal data according to standard EN 60335: Phase
1~
Nominal voltage
230 V
Frequency
50 Hz
Rated power input
28 W
Rated current
0.12 A
Rated speed
2500 RPM
Condensator
1 ÎźF/450 V
Connection
cable
Insulation class
155
Protection class
IP44
ErP data according to EU regulation 327/2011: Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
Code
Weight (kg)
R09X-2M-1533
0309-4-0155
1.9
158,5
87
92
150
29 20,5
Type
4x 4,4/90Ëš on
165,4 157,5
General notes Connection diagram: 132
0301-1-0026
Page 145
R09X-2M-2514
180 mm
Diameter:
EC axial fans
AC Radial fans Backward curved blades
Nominal data according to standard EN 60335:
50 Hz
Rated power input
80 W
Rated current
0.36 A
Rated speed
2450 RPM
Condensator
2.5 ÎźF/450 V
Connection
cable
Insulation class
155
Protection class
IP44 AC axial fans Plastic blades
Frequency
ErP data according to EU regulation 327/2011: Is not subject to the EU regulation 327/2011. Power input lower than 125 W.
48 33
Type
Code
Weight (kg)
R09X-2M-1533
0309-4-0304
2.0
98
20
196
92
4
180
AC axial fans Paddle blades
230 V AC axial fans Sickled blades
1~
Nominal voltage
200 190
General notes Connection diagram:
Connection diagramS
Accessories
4x 4,5/90Ëš on
AC radial fans backward curved blades
Phase
0301-1-0002
Page 145 133
06 Accessories
134
AC axial fans Paddle blades
AC axial fans Plastic blades
AC axial fans Sickled blades
EC axial fans
Accessories
AC radial fans backward curved blades
Accessories
Connection diagramS
Accessories
XXX Arciis erchic temolor empeles nam, quo tectorehenem fuga. Nam as simagniscia aut repelist quam sa que occae. Nemporionse volum none sam, sequae natur sus etur, nihil ipis aut es seque nations ecescit voluptatent ma nos aut ex et volorepedis et aut ut lamus et porem escit, earum.
135
Accessories
Accessories Main dimensions - Basket girlls Type 1 Fan dia
Motor type
A
B
C
D
E
∅F
G
H
Code
450
EC10
515
9
164
ø 6,5
534
475
47
82
0300-1-3349
450
EC10
515
9
164
ø 6,5
534
475
68
103
0300-1-3388
500
EC10
565
ø 11
164
ø 6,5
590
522
56
93
0300-1-3348
560
EC10
700
ø 11
164
ø 6,5
725
645
62
99
0300-1-3409
630
EC10
750
ø 11
164
ø 6,5
775
695
81
118
0300-1-3347
630
EC10
750
ø 11
164
ø 6,5
775
695
48
85
0300-1-3386
450
R13
515
ø 9,5
115
ø7
543
479
70
96
0300-1-3001
500
R13
565
ø 9,5
115
ø7
589
522
70
96
0300-1-3004
560
R13
700
ø 10,5
115
ø7
727
644
71.5
97.5
0300-1-3003
630
R13
750
ø 10,5
115
ø 10,5
784
690
70
96
0300-1-3006
Main dimensions - Basket girlls Type 2 Fan dia
Motor type
A
B
C
D
E
∅F
G
H
Code
250
EC09
300
6.5
125
4.5
314
269
37
45
0300-1-3218
300
EC09
360
6.5
125
4.5
376
316
53
61
0300-1-3217
330 / 315
EC09
400
6.5
125
4.5
416
356
67
75
0300-1-3215
350
EC09
442
6.5
125
4.5
460
376
76
84
0300-1-3198
200
R09
260
6.5
58
6.5
274
230
37
45
0300-1-3103
250
R09
300
6.5
58
6.5
314
269
37
45
0300-1-3104
300
R09
360
6.5
58
6.5
376
316
35
43
0300-1-3009
315
R09
375
6.5
58
6.5
393
336
57
65
0300-1-3022
350
R09
422
6.5
58
6.5
440
376
53
61
0300-1-3008
350
R11
442
6.5
90
6.5
485
376
53
61
0300-1-3027
400
R11
455
ø 9,5
90
ø 6,5
476
422
76
84
0300-1-3026
450
R11
520
10
90
10
540
480
55
73
0300-1-3000
Basket grills Type 1
Notes: Surface black painted RAL9005 136
Basket grills Type 2
Main dimensions - Basket girlls Type 3 Fan dia
Motor type
A
B
C
D
E
F
G
H
Code
500
EC10
519
ø 11
164
ø 6,5
537
511
1
50
0300-1-3381
560
EC10
578
ø 11
164
ø 6,5
596
570
6
66
0300-1-3398
630
EC10
654
ø7
164
ø 6,5
676
646
6
66
0300-1-3382
560
R13
579
ø7
115
ø7
601
571
17
94
0300-1-3089
630
R13
654
ø7
115
ø7
676
646
1
79
0300-1-3087
AC axial fans Sickled blades
EC axial fans
Accessories
Motor type
A
B
C
D
E
F
G
H
Code
710
R18
731
7,5 x 14,5
182
ø 11
777
715
32
112
0300-1-3077
800
R18
816
7,5 x 15,5
182
ø 11
816
795
30
112
0300-1-3072
Basket grills Type 4
Connection diagramS
Accessories
Basket grills Type 3
AC radial fans backward curved blades
AC axial fans Paddle blades
Fan dia
AC axial fans Plastic blades
Main dimensions - Basket girlls Type 4
Notes: Surface black painted RAL9005 137
Accessories
Main dimensions - Basket grills Type 5 Fan dia
Motor type
A
B
C
D
E
∅F
G
H
Code
300
R09
360
6.5
58
4.5
376
330
0
27
0300-1-3195
315
R09
375
6.5
58
4.5
392
344
0
27
0300-1-3194
330
R09
408
6.5
58
4.5
424
376
0
27
0300-1-3193
350
R09
422
6.5
58
4.5
438
376
0
27
0300-1-3192
400
EC10
455
9
164
ø 6,5
474
416
43
78
0300-1-3377
400
EC10
455
9
164
ø 6,5
474
416
68
103
0300-1-3369
420
EC10
483
9
164
ø 6,5
502
434
45
80
0300-1-3376
420
EC10
483
9
164
ø 6,5
502
434
68
103
0300-1-3389
400 / 420
EC10
502
9
164
ø 6,5
521
461
23
58
0300-1-3390
400 /420
EC10
502
9
164
ø 6,5
521
461
-7
28
0300-1-3385
450
EC10
560
9
164
ø 6,5
579
521
-7
28
0300-1-3383
450
EC10
560
9
164
ø 6,5
579
521
19
54
0300-1-3393
500
EC10
565
ø 11
164
ø 6,5
590
522
56
93
0300-1-3387
500
EC10
615
ø 11
164
ø 6,5
640
570
2
38
0300-1-3392
560
EC10
658
ø 11
164
ø 6,5
683
613
-6
30
0300-1-3408
630
EC10
720
ø 11
164
ø 6,5
745
675
-6
30
0300-1-3391
E
Main dimensions - Flat girlls Fan dia
Motor type
A
B
C
D
200
R09
250
6
58
4.5
314
0300-1-3094
250
R09
300
6
58
4.5
264
0300-1-3095
400
R11
467
6.5
90
6.5
490
0300-1-3128
450
R11
520
6.5
90
6.5
538
0300-1-3030
500
R11
565
9.5
90
6.5
586
0300-1-3031
560
R11
625
9.5
90
9.5
644
0300-1-3032
Basket grills Type 5
Notes: Surface black painted RAL9005 138
Flat grills
Code
Accessories
Airflow direction
A
B
∅C
∅D
∅E
qF
G
H
∅I
J
Code
300
sucking
360
M6
307
310
337
430
380
45
11
15
0300-6-7122
300
blowing
360
M6
307
310
337
430
380
45
11
15
0300-4-7073
315
sucking
375
M6
319
322
349
430
380
45
11
15
0300-6-7120
315
blowing
375
M6
319
322
349
430
380
45
11
15
0300-6-7075
330
sucking
400
M6
337
340
367
485
435
45
11
15
0300-6-7118
330
blowing
400
M6
337
340
367
485
435
45
11
15
0300-6-7104
350
sucking
422
M6
360
363
390
485
435
45
11
15
0300-6-7116
350
blowing
422
M6
360
363
390
485
435
45
11
15
0300-6-7077
400
sucking
455
M8
403
406
433
540
490
45
11
15
0300-6-7114
400
blowing
455
M8
403
406
433
540
490
45
11
15
0300-6-7079
420
sucking
483
M8
426
429
460
575
535
45
11
15
0300-6-7086
420
blowing
483
M8
426
429
460
575
535
45
11
15
0300-6-7087
450
sucking
515
M8
452
455
482
575
535
45
11
15
0300-6-7112
blowing
515
M8
452
455
482
575
535
45
11
15
0300-6-7069
sucking
565
M8
504
507
534
655
615
45
11
15
0300-6-7110
500
blowing
565
M8
504
507
534
655
615
45
11
15
0300-6-7081
560
sucking
700
M8
560
563
590
725
675
45
11
15
0300-6-7108
560
blowing
700
M8
560
563
590
725
675
45
11
15
0300-6-7083
630
sucking
750
M8
635
638
675
805
750
60
11
15
0300-6-7106
630
blowing
750
M8
635
638
675
805
750
60
11
15
0300-6-7071
AC radial fans backward curved blades
450 500
AC axial fans Plastic blades
Fan dia
AC axial fans Paddle blades
Main dimensions - Square short wall plates
AC axial fans Sickled blades
EC axial fans
Wall plates
Connection diagramS
Accessories
Square short wall plate
139
Accessories
Main dimensions - Square long wall plates Fan dia
Airflow direction
A
B
∅C
∅D
∅E
qF
G
H
∅I
J
Code
500
sucking
615
M8
504
518
585
656
615
118
11
16
0300-6-7089
560
sucking
658
M8
560
577
630
725
675
135
11
16
0300-6-7095
630
sucking
720
M8
634
653
695
805
750
150
11
20
0300-6-7091
710
sucking
/
/
711
729
790
850
810
167
14.5
20
0300-6-7085
800
sucking
/
/
797
815
915
970
910
210
14.5
17
0300-6-7068
∅D
∅E
∅F
G
H
∅I
J
Code
Square long wall plate
Main dimensions - Round long wall plates 1 Fan dia
Airflow direction
A
∅C
200
blowing
250
4.3
203
206
233
280
250
61
6.4
6.5
0300-6-7102
250
blowing
300
4.3
253
256
287
330
300
65
6.4
7.5
0300-6-7103
Round long wall plate Type 1
Notes: Surface black painted RAL9005 140
B
Main dimensions - Round long wall plates 2 Fan dia
Airflow direction
A
B
∅C
∅D
∅E
qF
G
H
∅I
J
Code
300
sucking
361
M6
306
326
397
/
380
80
9
11
0300-4-7144
315
sucking
375.5
M6
317
347
397
/
380.5
74
9
11
0300-6-7146
330
sucking
408
M6
336
369
440
/
404
80
9
9
0300-6-7148
350
sucking
422
M6
358
388
460
/
442
80
9
12
0300-6-7150
400
sucking
502
M6
400
419
528
/
504
96
9
12
0300-6-7166
420
sucking
502
M8
426
447
544
/
520
96
9
12
0300-6-7168
450
sucking
560
M8
454
465
607
/
578
100
9
14
0300-6-7170
Connection diagramS
Accessories
AC radial fans backward curved blades
AC axial fans Paddle blades
AC axial fans Plastic blades
Round long wall plate Type 2
AC axial fans Sickled blades
EC axial fans
Accessories
Notes: Surface black painted RAL9005 141
07 Connection diagrams
142
AC axial fans Paddle blades
AC axial fans Plastic blades
AC axial fans Sickled blades
EC axial fans
Connection diagrams
AC radial fans backward curved blades
Connection diagrams
Connection diagramS
Accessories
XXX Arciis erchic temolor empeles nam, quo tectorehenem fuga. Nam as simagniscia aut repelist quam sa que occae. Nemporionse volum none sam, sequae natur sus etur, nihil ipis aut es seque nations ecescit voluptatent ma nos aut ex et volorepedis et aut ut lamus et porem escit, earum.
143
Connection diagrams
Connection diagrams ■■ CConnection diagrams 0302-1-0000 Connecting diagram 0302-1-0000
EMI
BROWN BLUE
L
H-BUS
max 30mA
WHITE
BLACK
10k
R
or PWM
0-20mA
TACH GND
100k
GREY
CONTROL OPTIONS
0-10V
BLUE
+10VDC
PE
communication
470
• Dangeorus voltages, capacitor discharge time 5min!
N
GREEN/YELLOW
YELLOW
WARNING: WARNING: • Before box opening connection switch off - Before opening connection switch off electricbox power! electric power! - Dangeorus voltages, capacitor discharge time 5min!
TERMINAL BLOCK
CONTROL CABLE
PWM
Max. speed
analog input 0-10V
senzor (Variable resistance)
potentiometer
500
POWER CABLE
senzor
MOTOR FAN
0-20mA 0-20mA
PWM frequency input 1-10kHz
analog input 0-20mA
■■ Connection diagrams 0302-1-0100 Connecting diagram 0302-1-0100 POWER CABLE
Alarm relay NC
WHITE WHITE
EMI
BLACK BLUE
L N
H-BUS
max 30mA
RED
+10VDC
CONTROL OPTIONS 10k
R
0-10V or PWM
BLACK
0-20mA
PWM
senzor
470
CONTROL CABLE
GND
100k
PE
communication
BLUE
144
electric power! • Dangeorus voltages, capacitor discharge time 5min!
TK
GREEN/YELLOW
YELLOW
WARNING: WARNING: - Before opening connection box switch off electric power! • capacitor Before opening connection box switch off - Dangeorus voltages, discharge time 5min!
TK
Max. speed
analog input 0-10V
senzor (Variable resistance)
potentiometer
PWM frequency input 1-10kHz
500
MOTOR FAN
0-20mA 0-20mA
analog input 0-20mA
Connection diagrams
Conecting diagram 0301-1-0002
MOTOR
MODRA-BLUE
TP
PE
U2L (black)
N U1 (blue)
PE PE (ye/gr)
Join together
Join
[CA1,U2] together [CA2,Z2]
Protection device
Winding conection
Protection
Winding
Internally split phase device Permanent conection connected capacitor motor
U2 U1 PE [CA1, U2] Internally (black) (blue) (ye/gr) [CA2, Z2] connected
MOTOR
CA2
RJAVA - BROWN
AC axial fans Plastic blades
N
Permanent split phase capacitor motor
■■ Connection diagrams 0301-1-0044 Connecting diagram 0301-1-0044
CA1
MOTOR
Z1
BROWN ČRNA - BLACK
MODRA - BLUE
TP
RU/ZE-YE/GR
CW from cable side
N
PE
Join together
BLACK
L
U2
N
U1
TB
BLUE GREEN/YELLOW
L N PE
PE
PE
Protection device
Winding connection
Permanent split Winding U2 U1N PE PE [CA1,U2]Join InternalProtection L phase capacitor together conection (black) (blue) (ye/gr) [CA2,Z1] connected device motor Permanent U2 U1 PE [CA1, U2] Internally split phase (black) (blue) (ye/gr) [CA2, Z2] connected capacitor motor
Connection diagramS
cable side
L
AC axial fans Paddle blades
L
PE
PE
PE
Connecting diagram 0301-1-0026
CW from Rotation
N
GREEN/YELLOW
■■ Connection diagrams 0301-1-0026
Rotation
L
Z2
CCW from cable side
TB
BLUE
U1 U2
CCW from Rotation cable side
BLACK
N
U1
RU/ZE-YE/GR
Rotation
L
U2
U1 U2
ČRNA-BLACK
Z2
BROWN
AC axial fans Sickled blades
Z2
AC radial fans backward curved blades
RJAVA-BROWN
Connecting diagram 0301-1-0043
CA1
CA2
Accessories
MOTOR
■■ Connection diagrams 0301-1-0043
EC axial fans
■■ Connection diagrams 0301-1-0002
145
Connection diagrams ■■ Connection diagrams 0301-1-0029 Connecting diagram 0301-1-0029
MOTOR
CA1
■■ Connection diagrams 0301-1-0048 Connecting diagram 0301-1-0048 MOTOR
CA2
GREEN/YELLOW BLACK
U1 U2 Z1 Z2
ORANGE BLACK BLUE BROWN
TK TK
WHITE WHITE
TB
GREY BLUE RED
N
BROWN
L
ORANGE WHITE
CONTROL UNIT
TB
GREEN/YELLOW
WHITE
W1
L3
V2 V1
L2
U2 U1
L1
W2 TK TK
CONTROL UNIT
CONNECTION OPTIONS:
Connection options: L1 L2 L3 PE Protection
CONNECTION OPTIONS:
Rotation L1 N options: PE Protection Connection device CW from U1 U2 PE TK , TK cable side Rotation L1 N PE
Join together [CA1,U1]; Protection [CA2,Z2]; device [U2,Z1]
Winding connection 1.ph motor with Join capacitor and Winding together thermal contacts. connection
CW * TEMPERATURE MONITORS (TK) BUILT IN TO THE[CA1, U1] from WINDING SERVE AND U1 AS U2MOTOR PECUT-OUT TK,SWITCH TK [CA2, Z2] cable BE CONNECTED TO THE OUTSIDE CONTROL UNIT! MUST [U2, Z1] side
1.ph motor with capacitor and thermal contacts.
* Temperature monitors (TK) built in to the winding serve as motor cut-out switch and must be connected to the outside control unit!
■■ Connection diagrams 0301-1-0035 Connecting diagram 0301-1-0035
MOTOR
CA1
Join Winding device together connection Protection DELTA Join Winding U1L1 V1 W1 TK , TK PE [U1,W2]; (Δ)L2 PE L3 device hightogether connection [V1,U2]; speed [W1,V2] (STANDARD) [U1,W2]; DELTA (Δ) U1 V1 W1 PE TK , TK [U2.V2,W2] (Y) U1 V1 W1 PE TK, TK STAR [V1,U2]; high speed low speed [W1,V2] (STANDARD) * CHANGING OF ROTATION DIRECTION STAR (Y) BY OF 2 PHASES! U1INTERCHANGING V1 W1 PE TK, TK [U2,V2,W2]; * WITHOUT BRIDGES low speed WHEN USING SPEED-CHANGE OVER SWITCH! * TEMPERATURE MONITORS (TK) by BUILT IN TO THE of 2 phases! * Changing of rotation direction interchanging WINDING SERVE AS MOTOR CUT-OUT SWITCH AND * MUST Without bridges when using speed-change over switch! BE CONNECTED TO THE OUTSIDE CONTROL UNIT! * Temperature monitors (tk) built in to the winding serve as motor cut-out switch and must be connected to the outside control unit!
■■ Connection diagrams 0301-1-0049 Connecting diagram 0301-1-0049
CA2
MOTOR
GREEN/YELLOW BLACK
U1 U2 Z1 Z2
ORANGE BLACK BLUE BROWN
TK TK
WHITE WHITE
TB
GREY BLUE RED
N
BROWN
L
ORANGE
TB
GREEN/YELLOW
Protection Connection options: device CCW from U1 U2 PE TK , TK cable side
Rotation
L1
L1
N
PE
N
PE
Join together [U1,Z1]; [U2,CA1]; Protection [Z2,CA2] device
Winding connection 1.ph motor with Join capacitor and Winding thermal contacts. connection together
CCW * TEMPERATURE MONITORS (TK) BUILT IN TO THE [U1, Z1] WINDING SERVE AS MOTOR CUT-OUT SWITCH AND from U1 U2 TO THE PE OUTSIDE TK, TK [U2,UNIT! CA1] MUST BE CONNECTED CONTROL cable side
[Z2, CA2]
1.ph motor with capacitor and thermal contacts.
* Temperature monitors (TK) built in to the winding serve as motor cut-out switch and must be connected to the outside control unit!
146
WHITE
L3
V2 V1
L2
U2 U1
L1
W2 TK TK
CONTROL UNIT
CONNECTION OPTIONS:
CONNECTION OPTIONS: Rotation
WHITE
CONTROL UNIT
W1
L1 L2 L3 PE options: Protection Connection
Join Winding device together connection U1 V1 W1 PE TK , TK [U2.V2,W2] (Y) Protection STARJoin L1 L2 L3 PE voltage device hightogether (STANDARD) U1 V1 W1 PE TK , TK [U1,W2]; DELTA (Δ)U1 V1 W1 PE [V1,U2]; TK, TK low [U2,V2,W2] voltage [W1,V2]
* CHANGING OF ROTATION DIRECTION BY U1INTERCHANGING V1 W1OF 2 PHASES! PE TK, TK
[U1,W2]; [V1,U2]; [W1,V2]
Winding connection STAR (Y) high voltage (STANDARD) DELTA (Δ) low voltage
* TEMPERATURE MONITORS (TK) BUILT IN TO THE WINDING SERVE AS MOTOR CUT-OUT SWITCH AND * MUST Changing of rotation direction by interchanging of 2UNIT! phases! BE CONNECTED TO THE OUTSIDE CONTROL * Temperature monitors (tk) built in to the winding serve as motor cut-out switch and must be connected to the outside control unit!
Connection diagrams
Connecting diagram 0301-1-0031 MOTOR
BLACK GREY BLUE RED BROWN ORANGE TB TB
WHITE WHITE
W1
GREEN/YELLOW W1
L3
V2
L1
TK
CONNECTION OPTIONS: Connection options: L1 L2 L3 PE Protection L1 L2 L3devicePE U1 V1 W1 PE TK , TK
Join Protection together device [U1,W2]; [V1,U2]; [W1,V2] U1 V1 W1 PE TK, TK U1 V1 W1 PE TK , TK [U2.V2,W2]
CONTROL UNIT
Winding connection DELTA (Δ) high speed (STANDARD) STAR (Y) low speed
U1 V1OF ROTATION W1 PE TK, TK [U2,V2,W2]; * CHANGING DIRECTION BY INTERCHANGING OF 2 PHASES! * WITHOUT BRIDGES * WHEN Changing of rotation direction byOVER interchanging USING SPEED-CHANGE SWITCH! of 2 phases! * TEMPERATURE BUILT IN TOover THEswitch! * Without bridgesMONITORS when using(TK) speed-change SERVE AS MOTOR CUT-OUT SWITCH * WINDING Temperature monitors (tk) built in to the windingAND serve as motor cut-out switch and MUST BE connected CONNECTED TO THE OUTSIDE UNIT! must be to the outside controlCONTROL unit!
TK
TK
TP
TK
CONNECTION OPTIONS: L1 L2 L3 PE Protection Join Connection options: device together U1 V1 W1 PE TK , TK [U1,W2]; Protection L1 L2 L3 PE [V1,U2]; device [W1,V2] U1 V1 W1 PE TK , TK [U2.V2,W2] U1
V1
W1
L1
W2
TK
TP
Winding Join connection together DELTA (Δ)high speed [U1,W2]; (STANDARD) [V1,U2]; STAR (Y) low[W1,V2] speed
U1
W2
W2
L2
U2
U1
U1 TK
V1
U2
U2
L3
V2
V1
L2
V1
W1
V2
AC axial fans Sickled blades
GREEN/YELLOW
PE
PROTECTION DEVICE
Winding connection DELTAJoin () hightogether speed (STANDARD) [U1,W2]; STAR (Y) speed TK, TK low[V1,U2];
Winding connection DELTA (Δ) high speed (STANDARD)
[W1,V2] * CHANGING OF ROTATION DIRECTION BY INTERCHANGING OF 2 PHASES! STAR (Y) * U1 WITHOUTV1 BRIDGES W1 PE TK, TK [U2,V2,W2]; low speed WHEN USING SPEED-CHANGE OVER SWITCH! * Thermal contacts rating: AC 250V, 2.5A at cos =1.0, * 1.6A Changing by interchanging at cosof rotation =0.6,direction temperature sensing. of 2 phases! * Without bridges when using speed-change over switch! * Thermal contacts rating: AC 250V, 2.5A at cos ∅=1.0, 1.6A at cos ∅=0.6, temperature sensing.
AC axial fans Plastic blades
MOTOR
EC axial fans
■■ Connection diagrams 0301-1-0031
Connecting diagram 0301-1-0033
AC axial fans Paddle blades
■■ Connection diagrams 0301-1-0033
■■ Connection diagrams 0301-1-0034 MOTOR
AC radial fans backward curved blades
Connecting diagram 0301-1-0034
GREEN/YELLOW
GREY BLUE RED BROWN ORANGE TB TB
WHITE WHITE
W1
L3
V2 V1
L2
U2 U1
L1
W2 TK TK
CONTROL UNIT
Accessories
BLACK
CONNECTION OPTIONS: L1 L2 L3 PE Protection
Join Winding together connection U1 V1 W1 PE TK , TK [U2.V2,W2] STAR (Y) Protection high voltage Join L1 L2 L3 PE device (STANDARD) together U1 V1 W1 PE TK , TK [U1,W2]; DELTA (Δ)[V1,U2]; low voltage U1 V1 W1 PE [W1,V2] TK, TK [U2,V2,W2]
Connection options: device
Winding connection Connection diagramS
STAR (Y) high voltage (STANDARD)
* CHANGING OF ROTATION DIRECTION [U1,W2]; BY INTERCHANGING OF 2 PHASES! DELTA (Δ) U1 V1 W1 PE TK, TK [V1,U2]; low voltage * TEMPERATURE MONITORS (TK) BUILT IN TO THE [W1,V2] WINDING SERVE AS MOTOR CUT-OUT SWITCH AND BE CONNECTED TO THE OUTSIDE CONTROL * MUST Changing of rotation direction by interchanging of UNIT! 2 phases! * Temperature monitors (tk) built in to the winding serve as motor cut-out switch and must be connected to the outside control unit! 147
148
149
150
Sales and distribution: BENELUX ECR-Nederland BV Collseweg 26, 5674 TR Nuenen Postbus 16, 5670 AA Nuenen Nederland T: +31 (0)40 299 06 00 E: verkoop@ecr-nederland.nl www.ecr.nederland.nl
MIDDLE EAST Refrigeration Equipment / Panicker PO Box 3943 Dubai T: +971 4 2222349 E: sales@panickerholdings.com www.wearehvac.com
BULGARIA NOVOTECHPROM OOD 6000 Stara Zagora Kv. Industrialen Kaloianovsko shose str., 16 Bulgaria T: +359 42 603 309 E: ntp@novotechprom.com www.novotechprom.com
Ebrahim Al-Jassim Sons Trading Co., Ltd. PO Box.102, King Kaled St. DAMMAM-31411 Saudi Arabia T: +966 13 8332109 Extn. 111 E: mejassim@al-jassim.com SOUTHEAST ASIA Unite Access Company Limited 219/2 Asoke Towers Sukhumvit 21 (Soi Asoke), Khlongtoey Nua, Wattana Bangkok 10110 Thailand T: +66 2 1209622 E: hidria@hidria-thailand.com
Hidria Rotomatika d. o. o. Spodnja Kanomlja 23 5281 Spodnja Idrija, Slovenia T: +386 5 3756 000 E: sales.fans@hidria.com www.hidria.com
FINLAND and ESTONIA REFAIR OY Atomitie 1 FIN-00370 Helsinki Finland T: +358 9 5657780 E: info@refair.fi www.refair.fi GERMANY Sales office: Helmut Muehlenhoff Taubenstr. 18 85591 Vaterstetten T: +49(0)81069958944 E: helmut.muehlenhoff@tonline.de
ITALY SI.VEN Components s.r.l. Via P. Gorini 44 26900 Lodi Italy T: +39 0371428249 E: si.ven@tiscali.it KOREA DaeSung MAREF CO.,LTD 851-8, Hwasan-ri Ujeong-eup Hwaseong city Gyeonggi-do, Korea T: +82 31 421 8883 E: dsc@dsmaref.com RUSSIA Representative office Hidria Moscow Srednyaya Pereyaslavskaya str. 14 build 1, office 15-16 RU-129110 Moscow Rusija T: +7 (495) 974 1713 F: +7 (495) 974 1713 E: hidria.moscow@hidria.com www.hidria.com SLOVENIJA EMPOR Leskoškova 9a 1000 Ljubljana T: +386 1 5203820 E: empor@empor.si www.empor.si
SERBIA FRIGO RADAK COMPANY D.O.O. Đurđevdanska 20 11000 Beograd Serbia T: +381 11 3945577 M: +381 63 318539 SWEDEN and denmark NORDICOLD AB Datavägen 16, 43632 askim Sweden T: +46 31680440 E: info@nordicold.se www.nordicold.se USA Hidria USA Inc. 202 Beechtree Business Park Greenville, SC 29605 T: +1 864 331 0177 E: sarah.davis@ht-usa.com TURKEY FRIGOTERM Sog.Cih.San. ve Tic. A.S. Tarlabasi Caddesi No. 110, 80080 Beyoglu - Istanbul Turkey T: +90(0)2122371929 E: international@frigoterm.tr
Issue 03/14
Australia and New Zealand KCK Corporation Pty 84 Nortgate Drive, Thomastown, Vic 3074 Australia T: +61 3 94642066 F: +61 3 94642077 E: sales@hidria.com.au