MATT SATIN FINISH
RESIN FOR BLOCKS Polyurethane block sealer & sand binders
ROLL ON PROTECTION
Cementone Resin for Blocks is a one coat polyurethane sand binder and sealer for use on concrete block paving. Resin for Blocks impregnates the blocks and the jointing sand. When dry, the sand and the blocks are permanently bonded together to ensure the sand is not washed out of the joints and the paving is sealed from weed growth, efflorescence and stains. Ideal for natural look tumbled blocks.
JET WASH NO LOSS OF JOINTING SAND PREPARATION
• Only one coat is required.
Existing Drives
• Coat perimeter of area to be sealed up to the first joint line with a 10 cm (4”) paint brush.
• Paving must be clean and free of dust, weeds, algae, stains and efflorescence. • Jet washing is recommended.
• Binds sand and blocks together • Eliminates grass and weed growth in joints
Superior protection for drives, paths & patios
• Prevents re-occurrence of efflorescence • Jet wash without loss of sand • 1 coat system
Binds blocks and sand together permanently To bind sand and seal blocks for domestic paths, drives and patios • Concrete block paving
• Allow 2 weeks after cleaning to ensure efflorescence does not re-appear.
• Ensure the drive is clean and free of dust and any surface weakness such as efflorescence.
• Apply at a rate of 2 m2/litre to ensure good penetration. • Do not press too heavily on the roller. • Do not allow the sealer to pool. • If it is necessary to take a break, always stop along a joint line to avoid striping. • Leave sealed area to dry. This is usually about 2-6 hours for foot traffic and 24-48 hours for vehicles.
• For best results clean the blocks with Cementone Brick & Patio Cleaner to remove efflorescence; then wash down thoroughly with clean water.
SPECIFICATION
• Allow 8 weeks after cleaning to ensure efflorescence does not re-appear.
COLOURS:
Transparent, light straw.
Final Preparation
APPLICATION TEMPERATURE:
50 - 250C.
• Before applying the sealer, ensure there is no sand on the face or on the bevelled edges of the blocks.
DRYING TIMES:
2-6 hours approx. for foot traffic. 24-48 hours approx. for vehicular traffic.
• Protect adjacent surfaces, ponds and plants from splashing.
COVERAGE:
2 m2/litre.
HOW DOES IT WORK?
APPLICATION
SIZES:
5 litre, 25 litre.
Cementone Resin for Blocks impregnates the blocks and jointing sand to seal. It is absorbed into the sand to bond the grains together and to the blocks. This provides permanent, weatherproof and flexible joints.
• Resin for blocks should only be applied when the temperature is between 50 and 300C.
• Clay block paving
Prevents re-occurrence of efflorescence ROLL-ON BINDER
Available in Wet Look & Matt Satin 5L & 25L
• Replace or clean any badly stained blocks and treat efflorescence with Cementone Brick & Patio Cleaner.
New Drives USES
Eliminates grass and weed growth
• This may remove some of the jointing sand which must be replaced on the day the sealer is applied.
• Apply the resin with a watering can with a rose. Then coat the blocks using a short pile roller or squeegee, working diagonally across the joints from side to side, to prevent damage to the sand.
Traditionally, just kiln dried sand is brushed into the joints between blocks. In time, weeds and ants nests appear to spoil its appearance. Jet washing also blasts the sand out of the joints. Cementone Resin for Blocks prevents these problems and allows you to offer a superior, low maintenance path, drive or patio that has no weeds and is jet washable.
• On the day of sealing, ensure the paving is thoroughly dry (no rain for 48 hours). Brush fresh kiln dried sand into the joints with a soft broom.
• Wear protective gloves, clothing and goggles.
LIMITATIONS: NOT FOR INTERIOR USE due to lingering solvent odour. DO NOT USE around swimming pools.
1 Matt Satin resin protective top coat 2 Impregnation into block.
1 2 3
JET WASH - NO LOSS OF SAND
3 Fully absorbed into sand, bonding the grains together and to the blocks.
Cementone is a Registered Trade Mark of Bostik Limited Common Road, Stafford ST16 3EH. Tel: 01785 272764 Fax: 01785 272614 www.bostik.co.uk Evode Industries Limited., Newtown, Swords, Co. Dublin, Ireland. Tel: 01 862 4900 Fax: 01 840 2186
Ensure the surface is sound, clean and dry. Treat oil stains and efflorescence.
Brush fresh kiln dried sand into the joints.
Using a paint brush, coat perimeter blocks up to the first joint line.
Coat blocks using a short pile roller or squeegee.
WET LOOK FINISH
RESIN FOR BLOCKS Polyurethane block sealer & sand binders
ULTIMATE PROTECTION
Cementone Resin for Blocks is a polyurethane sealer and sand binder for use on concrete block paving. Resin for Blocks impregnates the blocks and the jointing sand. When dry, the sand and the blocks are permanently bonded together to ensure the sand is not washed out of the joints and the paving is sealed from weed growth, efflorescence and stains.
NO STAINING NOTHING GETS THROUGH PREPARATION
1st Coat
Existing Drives
• Coat perimeter of area to be sealed up to the first joint line with a 10 cm (4”) paint brush.
• Paving must be clean and free of dust, weeds, algae, stains and efflorescence. • Jet washing is recommended. • This may remove some of the jointing sand which must be replaced on the day the sealer is applied.
• Apply at a rate of 3 m2/litre to ensure good penetration.
• Replace or clean any badly stained blocks and treat efflorescence with Cementone Brick & Patio Cleaner.
• Do not allow the sealer to pool.
• Jet wash without loss of sand • Prevents re-occurrence of efflorescence
• Allow 2 weeks after cleaning to ensure efflorescence does not re-appear.
• Permanently binds blocks and sand together • Prevents oil staining
Superior protection for drives, paths & patios
• Eliminates grass and weed growth
Binds blocks and sand together permanently Jet wash - no loss of sand Eliminates grass and weed growth Prevents re-occurrence of efflorescence Available in Wet Look & Matt Satin 5L & 25L
• Coat the blocks using a short pile roller. Work diagonally across the joints from side to side.
• 2 coat system
• To seal blocks and sand together for domestic drives, paths and patios
• Ensure the drive is clean and free of dust and any surface weakness such as efflorescence.
• To seal concrete block pavers
• For best results clean the blocks with Cementone Brick & Patio Cleaner to remove efflorescence; then wash down thoroughly with clean water.
ROLL-ON AND FORGET
• Allow 8 weeks after cleaning to ensure efflorescence does not re-appear.
Traditionally, just kiln dried sand is brushed into the joints between blocks. Over time, weeds and ants nests appear and oil can stain the blocks, spoiling the appearance. Jet washing also blasts the sand out of the joints requiring the labour of brushing in new sand. Cementone Resin for Blocks overcomes these problems and allows you to offer your customers a superior, low maintenance path, drive or patio because there are no weeds and it is jet washable. HOW DOES IT WORK?
• If it is necessary to take a break, always stop along a joint line to avoid striping. 2nd Coat
New Drives
USES
• Do not press too heavily on the roller.
• Apply second coat after 3-4 hours, preferably on the same day but no longer than 24 hours. • Work at right angles to the first coat and apply an even coat at 6 m2/litre. • Leave sealed area to dry. This is usually about 4-6 hours for foot traffic and 24-48 hours for vehicles. SPECIFICATION
Final Preparation • On the day of sealing, ensure the paving is thoroughly dry (no rain for 48 hours). Brush fresh kiln dried sand into the joints with a soft broom. • Before applying the sealer, ensure there is no sand on the face or on the bevelled edges of the blocks.
COLOURS:
Transparent, light straw.
APPLICATION TEMPERATURE:
50 - 250C.
DRYING TIMES:
2-6 hours approx. for foot traffic. 24-48 hours approx. for vehicular traffic.
COVERAGE:
First coat: 3 m2/litre. Second coat: 6 m2/litre.
SIZES:
5 litre, 25 litre.
• Protect adjacent surfaces, ponds and plants from splashing. APPLICATION
Cementone Resin for Blocks impregnates the blocks and provides a protective armour to the top of the blocks. This prevents oil and grease from penetrating into the blocks to leave ugly stains. Cementone Resin for Blocks is also absorbed into the sand bonding the grains together and to the blocks to provide permanent weatherproof and flexible joints.
• Resin for blocks should only be applied when the temperature is between 50 and 300C. • Wear protective gloves, clothing and goggles. • 2 coat system for maximum protection and enhanced appearance.
LIMITATIONS: NOT FOR INTERIOR USE due to lingering solvent odour. DO NOT USE around swimming pools. USE FOR CONCRETE PAVING BLOCKS ONLY. *No more oil stains Wet Look finish only
1 Wet Look resin 2 top coats for protection. 2 Impregnation into block.
1 2 3
NO MORE OIL STAINS*
3 Fully absorbed into sand, bonding the grains together and to the blocks.
Cementone is a Registered Trade Mark of Bostik Limited Common Road, Stafford ST16 3EH. Tel: 01785 272764 Fax: 01785 272614 www.bostik.co.uk Evode Industries Limited., Newtown, Swords, Co. Dublin, Ireland. Tel: 01 862 4900 Fax: 01 840 2186
Ensure the surface is sound, clean and dry. Treat oil stains and efflorescence.
Brush fresh kiln dried sand into the joints.
Using a paint brush, coat perimeter blocks up to the first joint line.
Coat blocks using a short pile roller.