©
New Company, New Name... Same Quality and Design for Over 30 Years!
©
SNOWBLOWERS by TEAMCO, INC. www.teamcoinc.com
Power Through The Snow! Teamco snowblowers achieve high efficiency with great durability and less plugging due to the single stage design using 2 fans and a large 12” x 12” discharge throat for each fan. Many foreign objects maybe buried under the snow such as rocks, tires, cement blocks and chains. We do not recommend blowing these objects, however, since they are hidden under the snow they are subject to being struck by the snowblower. The Snowblast is designed to take such abuse without doing a large amount of damage to the snowblower. The Snowblast “A” series, depending on model, uses 6, 8 or 9 fan paddles in place of 4 on each fan for greater efficiency and smoother operation.
© ©
www.teamcoinc.com 605-498-0610
Shown with optional Hydraulic Spout Cappers and Side Extensions
Standard Equipment and Specifications Model:
8600A
9600A
10800A
12900A
Cutting Width 96” (8 ft.) 108” (9 ft.) 120” (10 ft.) 144” (12 ft.) Cutting Height 48” (4 ft.) 60” (5 ft.) 66” (5-1/2 ft.) 78” (6-1/2 ft.) Operating Horsepower 90-180 hp 120-275 hp 200-375 hp 250-425 hp Fan Shaft and Bearings 2-1/4” 2-7/16” 3” 3-7/16” Drive Chain 80 80-2 80-3 80-4 Drive Chain System Oil Bath Oil Bath Oil Bath Oil Bath Fan Backs 3/8” 3/8” 3/8” 3/8” Fan Paddles 3/8” 3/8” 3/8” 3/8” Paddles per Fan 6 6 8 9 Fan Liner 1/4” 1/4” 1/4” 1/4” Snowblower Housing 7 Ga. 7 Ga. 7 Ga. 7 Ga. Number of Spouts 2 2 2 2 Spout Backs 7 Ga. 7 Ga. 7 Ga. 7 Ga. Spout Sides 10 Ga. 10 Ga. 10 Ga. 10 Ga. Hitch (CAT) II/III II/III III/IV/IVN III/IV/IVN Weight (Approx.) 3300 lbs. 4300 lbs. 6100 lbs. 7900 lbs. Note: SNOWBLAST by Teamco reserves the right to change the above specifications at its own discretion.
There Is No Better Built Snowblower on the Market! Backed by a 2 Year Limited Warranty! The fan takes both cylindrical and thrust pressures from the snow as it progresses through the snow. Thrust pressures are transmitted through the fan and shaft
into a 4 bolt piloted flange bearing and then into an oil bath housing designed to absorb cylindrical and thrust pressure into the 3 pt. hitch of the snowblower. On most typical snowblower shaft and bearing designs a 2 bolt pillow block has to accept all the thrust and torque, thus resulting in the 2 bolts and the base of the block to accept all forces. Teamco “A” series snowblowers incorporates a 4 bolt piloted flange bearing. In this manner, as you can see in this illustration, the bearing is held into place by 4 bolts for thrust pressures and accurate holes accept the piloted portion of the bearing so that all cylindrical pressures are directly supported by the steel housing and oil reservoir that is mounted directly onto the bottom arms of the snowblower, thus resulting in all the
Available in a wide variety of sizes and models with horsepower requirements from 90-425 HP.
thrust and cylindrical pressures being transmitted to the ideal point of the snowblower, which is the hitch where the stresses are transmitted to the tractor.
Engineering Is The Difference Engineering quality is what the Teamco Snowblast “A” series snowblowers is all about. Teamco’s superior engineering and design means less trouble and breakdowns for you. Take a close look at the above illustration. Here we are illustrating how a shaft, out of alignment, can cause excessive loss of life on expensive component parts. Teamco aligns bearings and shafts so they are parallel. By having the shafts in accurate alignment all chains and sprockets run in alignment; 1. Creating equal side pressure on side links of roller chain and rollers, 2. Preventing excessive wear on sprockets and 3. Incorporating oil on the roller chain and sprockets further enhances the life of chain and sprockets. The big difference is that on most snowblowers, chains are open to snow conditions which are very abrasive on roller chains, so by enclosing
the chain in a concealed reservoir and bathing the roller chain, it will multiply the life of the chain considerably. Review these points before you purchase
a snowblower and see if any other snowblower compares with the quality and workmanship of the Teamco Snowblast “A” series.
A. Exaggerated view showing shaft in misalignment. B. Note stresses on both links of roller chain. Perfect alignment of shafts assuring long sprocket and chain life. 1. Chains in oil bath reservoir 2. Fan shafts and sprockets in true alignment 3. Long sprocket life 4. Long roller chain life 5. 4 bolt piloted flange bearings 6. Force being directed through bearings and housing into frame of snowblower and 3 pt. hitch 7. Quick hitch adaptable 8. Heavy duty hitch design 9. Heavy duty frame 10. Heavy fan liners 11. 7 ga. or 3/16” spout backs 12. 10 ga. or 1/8” spout sides 13. 16 spout hold-downs with 2 bearings on each hold-down 14. Approximately 180º spout rotation 15. Workmanship 16. Bolt-on Cutting Edge (Standard) 17. Adjustable Skid Shoes (Standard) 18. Side Extension Ready (Standard) 19. Cylinder and Hoses for spout rotation (Standard) ©
Manufacturer of
©
Snowblowers
Teamco is your OEM supplier and manufacture of Wildcat® snowblower parts.
Tel: 605-498-0610 • Fax: 605-498-0609 27065 Kerslake Pl. , Tea, SD 57064 www.teamcoinc.com
Truck loading and self-powered commercial units also available.